irdeto ca satellite receiver - home2ushome2us.com/b2c/media/smp6200 user manual.pdf2 digital...

DIGITAL SET-TOP-BOX

Irdeto CA Satellite Receiver

SMP-6200

USER’S MANUAL

Digital Satellite Receiver SMP-6200

Table of Contents 1. PRE-INSTALLATION CHECKUP 3 2. SAFETY WARNINGS 4 3. CONNECTIONS 6 4. REMOTE CONTROL 8 4.1 Remote Control Unit 9 5. MENU INSTRUCTION 10 5.1 Main Menu 10 5.1.1 TV Guide 11

5.1.2 Radio Guide 11 5.1.3 Installation 12 5.1.3.1 Installation 12

5.1.3.1.1 Antenna Setting 13 5.1.3.1.2 Auto Searching 17

5.1.3.1.3 Manual Searching 18 5.1.3.1.4 Factory Default 24 5.1.4 Channel Management 24 5.1.4.1 Favorite/Lock Channel 25 5.1.4.2 Edit Channel 25 5.1.4.2.1 Move 26

5.1.4.2.2 Delete 26 5.1.4.2.3 Rename 27

5.1.4.3 Delete TP 27 5.1.5 System Setting 28 5.1.5.1 Time Setting 28

5.1.5.2 A/V Output 28 5.1.5.3 Parental Control 29 5.1.5.4 Timer 31 5.1.5.5 Power up Channel 31

5.1.6 System Information 32 5.1.6.1 CA Status 32 5.1.6.2 IRD Status 33

5.1.6.3 Load Status 33 5.1.6.4 Mail Message 34

5.1.6.5 Announcement 34 5.1.6.6 Upgrade software 34

6. SPECIFICATIONS 35 6.1 Compliance 35 6.2 Major Features 35

2 Digital Satellite Receiver SMP-6200 1. PRE-INSTALLATION CHECKUP Please check the following items after opening the package: digital satellite receiver, remote control, battery, A/V cable, RF cable, and user’s manual. Please keep the packing box, packing materials, and plastic bag in safe place for repackaging in the future.

3 Digital Satellite Receiver SMP-6200 2. SAFETY WARNINGS

The normal operating temperature of the digital satellite receiver is between 0ºC and 40ºC.

Please prevent the receiver from operating in dusty conditions.

The receiver shall be operated in ventilated environment away from heat sources.

Do not open or disassemble the outer chassis in order to avoid the danger of electric shock and damaging to the receiver. Opening the chassis will also void the warranty.

4 Digital Satellite Receiver SMP-6200

The satellite antenna that is connected to the receiver shall be equipped with anti-shock device from lightning.

When the receiver is inoperative, please consult the Customer Support.

5 Digital Satellite Receiver SMP-6200 3. CONNECTIONS Please refer to Figure 1 and Figure 2 for the following instructions. Connect the LNB cable from the dish antenna to the LNB IN connector on the back of the digital satellite receiver. Use the RCA audio/video cables to connect the Audio Left, Audio Right, and Video Output to the corresponding connectors on TV.

Figure 1 Front Panel POWER/ESC To switch between standby and power-on states.

To adjust the volume output of the receiver when receiving TV programs, or change parameters within the menu.

When receiving TV programs, pressing these keys switches to the next higher or lower numbered

program, or to move the scroll bar up or down on the menu. MENU To bring up the main menu, or exit from menu or submenu. SELECT To enter the next lower level submenu or to confirm the parameter value entered.


Figure 2 Rear Panel LNB OUT Satellite signal loop through terminal LNB IN Satellite signal input terminal from LNB RS-232 RS-232 serial port S-VIDEO Connect to S-VIDEO Jack of the TV or VCR VIDEO (Yellow) Line signal output of video AUDIO (White) Line signal output of left audio channel AUDIO (Red) Line signal output of right audio channel DIGITAL AUDIO Connect to digital amplifier RF OUT RF signal output to TV PAL CH21-69 NTSC CH3-4 RF IN RF signal input from ANT or CATV system AC 90-240V AC power cord 50Hz/60Hz POWER Receiver power switch

7 Digital Satellite Receiver SMP-6200 4. REMOTE CONTROL

KEY FUNCTION

POWER Turns power ON/OFF of the receiver.

MAIL Directly goes into mail screen.

TV/AV Switch output between TV, AV and VCR.

TV/RADIO Switches between TV and Radio mode.

0~9 Enters number of the required menu item or selects a channel number to watch.

SIGNAL Displays the signal strength and quality information.

FAVLIST Displays the favorite channel list.

FAV+ / FAV- Moves up/down in the favorite channel list.

TIMER Calls up Timer Recording Table.

EPG Calls up the EPG (Electronic Program Guide).

AUD Selects the audio input mode.

INFO Displays the selected channel information in TV guide screen or radio guide screen.

PRV Returns to the previous channel.

R/L Selects the different audio output modes.

EXIT Exits from current menu/submenu.

MENU Presses this key one time to run menu on screen and calls command box.

OK Executes the selected item in the menu screen, or enters the desired value in any input mode.

CH+, CH- These keys are used to switch to the next higher or lower program, or to move the scroll bar up or down in the menu.

VOL+, VOL- These keys are used to adjust the volume output level of the receiver, or to select the next available parameters within the menu.

MUTE This key is used to toggle in or out of muting mode.

Figure 3 Remote Control

TELETEXT Display teletext, if there is teletext information in stream.

8

Digital Satellite Receiver SMP-6200 4.1 Remote Control Unit Please refer to the following diagram (Figure 4) when using the remote control. The maximum distance for usage is 10 meters (30 feet) with look angle 60 degrees. Please aim the infrared transmitter in the front of the remote control to the front panel of the receiver.

Figure 4 Remote Control Unit Range

9

Digital Satellite Receiver SMP-6200 5. MENU INSTRUCTION 5.1 Main Menu The contents of main menu are as follows:

Main Menu

Installation

Channel Management

System Setting

System Information

Move Select Exit OK EXIT

Installation Installation is used to search for new services or to edit existing ones. It can also be used to load the default setup of the receiver. Channel Management This is used to edit the downloaded channels, to set the favorite channels and to lock channels. User can also delete the stored TP. System Settings The system settings provide a convenient way of selecting different power-up channels, adjusting the time and A/V output mode, and adjusting parental control rating. System Information System information provides all information regarding the receiver, including CA, loader, mail message, announcement, and all details of the upgraded software.

10

Digital Satellite Receiver SMP-6200 5.1.1 TV Guide This shows the list of TV program, press OK button can enter to TV guide.

You can select one of the TV programs (event name) by pressing / keys follow with pressing the OK key. You can press the Info button to show the channel information.

8. Suroyo TV 7. CMC 6. HRT 5. CGNTV 4. Planeta TV 3. VPTV 2. TV TWRAM

1. Lawyers TV

Main Menu TV Guide

5.1.2 Radio Guide This shows the list of Radio program, press TV/Radio key to change the options between

“TV guide” and “Radio Guide” in TV guide screen.

You can access one of the Radio programs (event name) by pressing / keys follow with pressing the OK key. You can press the Info button to show the channel information.

2. Radio 2 3. Radio 3 4. Radio 4 5. Radio 5 6. Radio 6 7. Radio 7 8. Radio 8

1. Radio 1

Main Menu Radio Guide

11 Digital Satellite Receiver SMP-6200 5.1.3 Installation Installation is used to search for new services or edit existing ones. It can also be used to load the default setup of the receiver. To enter this menu, you have to input the PIN Code first. The default PIN Code is 0000.

Main Menu

Installation

Channel Management

System Setting

System Information

xx

Please Input Your Password

Message Box

Move Select Exit

OK EXIT

5.1.3.1 Installation This menu provides all the settings for customizing. There are two ways in searching new services, auto search and manual search. Resetting to default setup is also set in this menu.

Installation Main Menu

Antenna Setting Auto Search

Manual Search Factory Default


12 Digital Satellite Receiver SMP-6200 5.1.3.1.1 Antenna Setting

You can select the Antenna and LNB settings for service searching, as well as the settings of 22KHz tone and DiSEqC switch and dish options. There are 32 possible antenna settings. The values set in this menu are available for selection in other Service Searching Menus. LNB type has two options to switch to, normal and universal. If normal is selected, there will be only one Freq available. If universal is selected, there will be two frequencies provided to be selected, i.e., LNBF Freq low and LNB Freq High.

Antenna Setting Installation Main Menu

● Antenna AMC-4

● LNB Type Normal

● Frequency 12120

● LNB Power ON ● 22KHz AUTO ● DiSEqC OFF ● Dish FIXED

● Save ● Auto Search Move OK OK

● Save & Exit

Select Exit EXIT

Press / keys to choose between the following items, press / to change its value. Press OK to show all available options.

Antenna It shows the satellite name. User can select the satellite name by pressing / keys. The total

number is 32.


LNB Type There is two options to be selected from: normal and universal. Press / keys to switch between

the options. If normal is selected, the figure is as above, if the universal is selected, the figure is as following:


● Antenna AMC-4 ● LNB Type Universal ● LNB Freq Low 9750

● LNB Freq High 10600 ● LNB Power ON ● 22KHz AUTO ● DiSEqC OFF ● Dish FIXED

● Save ● Auto Search Move OK

● Save & Exit

Select Exit

OK

EXIT

14 Digital Satellite Receiver SMP-6200 Frequency When the LNB Frequency is single, press OK to display the list of Frequency, then press / keys

to select. User can always select “user defined” to add a new Frequency.


● Antenna AMC-4

1. 5150 2. 9750 3. 10600 4. 10700 5. 10750 6. 11200

3. 10600

● LNB Type Normal

● Frequency 12120

● LNB Power ON

● 22KHz ON

● DiSEqC OFF

● Dish FIXED


● Save & Exit

Select Exit EXIT

LNB Power Press / keys to switch the LNB Power between ON and OFF. 22KHz When LNB type is set to normal, 22KHz has two different options: ON and OFF. When LNB type is

set to universal, 22KHz will be auto selected. Press / keys to change between the options. Set OFF to select dual-LNB or set ON to select two antennas connected to a 22KHz tone switch.

DiSEqC According to the option and position of DiSEqC switch, you can select from A to D of DiSEqC and turn it OFF.

Dish Press / keys to switch between the options fixed and motor. Setting to fixed, the dish can not be

moved. Setting to motor, the dish will be movable. Help Menu Press / keys to select between the following items, press / or input 0~9 to change its value:

press OK to show all available options. Press Red key on remote to save the settings. The saved message will be displayed. After saving, this menu will remain the same.



● Antenna AMC-4

● LNB Type Normal

● Frequency

● LNB Power

● 22KHz

● DiSEqC

11300

13/18V

AUTO

OFF

Saving data, Please wait…

Message Box

● Dish FIXED


● Save & Exit

Select Exit EXIT

Press Blue key on remote, the setting will be saved and meanwhile it returns to the previous menu. Press Green key on remote, it will directly get into auto search menu.

16 Digital Satellite Receiver SMP-6200 5.1.3.1.2 Auto Searching To enter this menu, user can press OK key from the installation screen. There are two bars on the bottom to indicate the signal strength and quality. The bars in green color show the signal is in good condition. This menu will automatically search for the existing channels by the frequencies.

Auto Search Installation Main Menu

● Satellite AMC-4 ● Frequency 12120 ● Scan mode All

● Start Scan Move OK OK

● Antenna Setup Select Exit EXIT

Satellite It shows the satellite name. User can select the satellite name by pressing / keys. The total number is 32. Press OK key to show all satellite lists.

Frequency It shows the frequency of the transponder user selected. The corresponding symbol rate and polarization that have been confirmed. Press OK to display the list of existing frequencies.

Scan Mode It shows two scan modes in this entry by pressing / key. Set scan mode to all, all the channels in the transponder you selected will be download if the signal is locked. Set scan mode to FTA, only free-to-air channels can be downloaded.

Help Menu Press / keys to select between the following items, press / or input 0~9 to change its value: press OK to show all available options.

Press Red key on remote to get into search menu. Press Blue key on remote to return to antenna setting menu.

17 Digital Satellite Receiver SMP-6200 5.1.3.1.3 Manual Searching

After setting the search parameters like frequency, symbol rate etc, you can find the services in the transponder you selected. There are two bars on the bottom to indicate the signal strength and quality. The bars in red color show the signal is in good conditions.

Manual Search Installation Main Menu

● Satellite AMC-4 ● Frequency 12120 ● Symbol Rate 30000

● Polarization V 60%

76%

● Start Scan ● Edit TP Move OK

● Antenna Setup

● Scan Mode All

● Network Search Off

● PID Search Off

Strength

Quality

OK

Select Exit EXIT

You can press / keys to select between the following items, press / key or 0…9 to change its value.

18 Digital Satellite Receiver SMP-6200 Satellite It shows the satellite name. User can select the satellite name by pressing / keys. The total

number is 32. Press OK key to show all satellite lists.


● Satellite AMC-4

Galaxy 16 IA 5 Galaxy 3C IA 6

AMC-1

2. 9750 AMC-4 ● Frequency 12120

● Symbol Rate 30000

● Polarization V

● Scan Mode All

● Network Search Off ● PID Search Off

60% Strength

76% Quality

● Start Scan ● Edit TP Move OK OK

● Antenna Setup

Select Exit EXIT

19 Digital Satellite Receiver SMP-6200 Frequency It shows the frequency of the transponder user selected. Press OK to display the list of existing

frequencies. If the frequency exists in the list, the corresponding symbol rate and polarization are also confirmed.


● Satellite AMC-4

● Frequency 12120

2. 3706 3. 3760 4. 3840 5. 3860 6. 3880

1. 4000 1. 4000

● Symbol Rate 30000

● Polarization V

● Scan Mode All ● Network Search Off ● PID Search Off

60% Strength

76% Quality


● Antenna Setup

Select Exit EXIT

When user selects new TP stored on the bottom of the list, user can input the frequency by using digital keys from 0 to 9; furthermore, the symbol rate and polarization also need to be input by user. User can set the polarization of the transponder to Horizontal or Vertical. In horizontal case, the 18V and in vertical case, the 13V are output through LNB line.



● Satellite AMC-4

● Frequency

● Symbol Rate

● Polarization V

● Scan Mode All

● Network Search Off ● PID Search Off

60% Strength

76% Quality


● Antenna Setup

Select Exit EXIT

Scan Mode There are two scan modes in this entry, select by pressing / key. If scan mode is set to ‘All’, all

the channels in the transponder that are selected will be downloaded when the signal is locked. If scan mode is set to ‘FTA’, only free-to-air channels will be downloaded.

Network Search Press / key to select either ON or OFF. When ‘ON’ is selected, pressing the Red key will bring the menu to TP search menu and all the channels in the network table will be downloaded.

PID Search In PID search mode (ON), user is provided with the searching of a specified services by inputting it’s a/V/PCR PID’s. When ‘ON’ is set and ‘OK’ is pressed, user will be able to search by PID menu. User can set the PID information in services searching. The PID is in decimal value. Press the keys 0…9 to enter the value. The meanings of these items are explained in Manual Searching menu except for: PCR PID This is used to set PCR PID of certain service. V PID This is used to set Video PID of certain service. A PID This is used to set Audio PID of certain service.



AMC-4 ● Satellite ● Frequency 12120 ● Symbol Rate 30000

● Polarization V ● PID Search On

● Video PID

● Audio PID

● PCR PID

0% Strength

0% Quality


● Antenna Setup

Select Exit

EXIT

After setting these values, press Red key to perform service searching or press MENU key to exit.

22 Digital Satellite Receiver SMP-6200 TP Scan Menu


TV Radio

12120 V 30000 Ksps

60%

76%

Move Select Exit

2. TV TWRAM 3. VPTV 4. Planeta TV 5. CGNTV

1. 1. Lawyers TV

Strength

Quality

OK EXIT

Start Scan Press Red key to get into TP Scan menu. Antenna Setup Press Blue key to return to antenna setting menu. Edit TP Press Green key to edit the current TP parameter. After setting these values, press Red key to perform service searching or press MENU key to exit.

23 Digital Satellite Receiver SMP-6200 5.1.3.1.4 Factory Default When you select YES, the system setup and channel data will be changed to the default values. All the service information manually entered by user will be lost! To exit, select NO or press MENU key.

Factory Default Installation Main Menu

Left/Right Save Exit

This will turn STB into factory default status. Do you still want to proceed?

●YES ●NO

Message Box

OK EXIT

5.1.4 Channel Management This menu gives user the options to mark Favorite / Lock their TV and Radio channels. User can Rename, Delete, Move and Edit an existing service. Besides services, all existing TP can also be deleted.

Channel Management Main Menu

Favorite/Lock Channel Edit Channel

Delete TP

Move Select Exit

OK EXIT

24 Digital Satellite Receiver SMP-6200 5.1.4.1 Favorite/Lock Channel This menu allows users to mark favorite/lock the existing channels.

1. Press OK key to enter the favorite/lock menu 2. Press / key to select a channel. 3. Press Yellow key to mark favorite for channel you selected. 4. Press Blue key to lock the channel you selected. 5. Press TV/RADIO key to switch the channel list between TV and Radio. 6. Press Exit key to exit this menu. Upon exiting, a message box will be displayed.

Favorite/Lock Channel Channel Management Main Menu

2. TV TWRAM 3. VPTV 4. Planeta TV 5. CGNTV 6. HRT 7. CMC 8. Suroyo TV

1. Lawyers TV

● Favorite Move

● Lock Exit EXIT

5.1.4.2 Edit Channel This menu allows users to Move, Delete and Rename TV services.

Edit Channel Channel Management Main Menu

Move

Delete

Rename


25 Digital Satellite Receiver SMP-6200 5.1.4.2.1 Move 1. Press / key to select a channel that you would like to move.

2. Press OK key to confirm. The color of this service will become grey. 3. Press the / key to move the highlighted channel to a new position. 4. Press the OK key to confirm. There will be a message box indicating ‘Yes’ or ‘No’ selections. Press YES to final confirm or press NO to cancel.

Move Edit Channel Channel Management Main Menu


1. Lawyers TV

Move Left/Right Exit Move/Confirm

EXIT

OK

5.1.4.2.2 Delete User can delete unwanted channels by: 1. Press / key to select a channel that you would like to delete. 2. Press OK key, a message box will appear. 3. Select ‘No’ to cancel or ‘Yes’ to confirm.

Delete Edit Channel Channel Management Main Menu


1. Lawyers TV

Move Left/Right Exit EXIT

OK to delete

OK

26 Digital Satellite Receiver SMP-6200 5.1.4.2.3 Rename 1. Press / key to move to the service.

2. Press OK key, the ‘Rename’ box will appear. 3. Press / or / key to select the desired character. 4. Press key to select OK key. 5. Press OK key to confirm or MENU key to discard the changes and exit.

Move Left/Right Exit OK to rename

5.1.4.3 Delete TP 1. Press / key to move to the satellite you want to select in satellite list.

2. Press / or key to select the TP you want to delete. 3. Press / key to move to the TP you want to select in transponder list. 4. Press OK key, a confirmation message box will appear.

5. Select YES to delete or NO to cancel.

Main Menu Channel Management Edit Channel

1. 745 XING KONG 2. 715 Ph’x Movies 3. 721 Movies Int’l 4. u itl T t.S bt e es 5. STAR Movies Int’l 6. 726 Ph’x Info 7. 739 Movi s Int’l e8. 7 es 43 Phoenix Chin16. 604 Channel [V] In

Rename

EXIT

OK

OK Exit11.748 Star World Asi

Main Menu Channel Management Delete TP

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L b c D

v w

X

N O P Q R S T U V W h i j k l m n o p q . + - $ @ ! <

X Y Z a r s t u

M e f g y z

Move Left/Right Exit OK to delete

Galaxy 16 IA 5 Galaxy 3C IA 6 Galaxy 11 AMC3

AMC-4

EXIT

OK

1. 12120 2. 12120 3. 12120

Satellite Transponder

27 Digital Satellite Receiver SMP-6200 5.1.5 System Setting 5.1.5.1 Time Setting Time Zone Set the local time zone offset of GMT from –12 to +12.

Summer Time Set it to ON or OFF. ‘ON’ means summer time function works. Year/Month/Day/Hour. This option is only provided to show the current time. It is not

changeable by user.

Time Setting System Setting Main Menu

● Time Zone GMT ● Summer Time OFF ● Year 2006 ● Month 1

● Day 5

● Hour 03:21

Left/Right Save Exit OK EXIT

5.1.5.2 A/V Output

A/V Output System Setting Main Menu

● Menu Language English ● Brightness 64

● Color 48

● TV Screen 4:3

● TV Type AUTO

● Volume Control OFF

● Transparent 10%

● RF Tuner NTSC

● RF Channel 38 ● SCART Format SVIDEO

Move Left/Right Exit EXIT

Save

OK

28 Digital Satellite Receiver SMP-6200 Menu Language User can select the menu language, such as English, Chinese, etc. Brightness User can select the brightness value. Color User can select the color value. TV Screen User can set the screen aspect ratio of TV (4:3,4:3panscan, 4:3LB, 16:9, or 16:9pillar) TV Type User can set the video output mode to Auto, NTSC or PAL. Volume Control User can set the volume control mode to ON or OFF. If ON is set, the volume is not

adjustable, if OFF is set, the volume is adjustable. Transparent User can adjust transparent to any status from 0% to 100%. RF Tuner User can select RF output mode of NTSC, PAL_DK, PAL_BG, PAL_I if RF is enabled. RF Channel User can select the RF output channel from 21 to 69. SCART Format User can set scart output format Press OK key to save the changed settings or press EXIT to cancel. 5.1.5.3 Parental Control To enter this menu, the current password is required. The default password is “0000”.

Move Select Exit

EXITOK

Please Input Your Password

Message Box

Time Setting

System Setting Main Menu

29 Digital Satellite Receiver SMP-6200 Parental Control User can press / key to switch select parental control option among UNBLOCK, 10,13,

16, 18 and ALL_BLOCK.

Move Left/Right Exit Save

UNLOCK If set to ‘UNBlock’, all the channels are viewable no matter the selected channel is

categorized by age 10/13/16/18. If set to ‘10/13/16/18’, only users whose age is equal to or more than the channel’s defined can view the particular channel.

ALL_BLOCK If set to ‘All_Block’, all the channels are not viewable until a correct pin code is keyed in by

user. New Pin Code To change the Pin Code, input new Pin code (four digits) Confirm Password Confirm the new pin code if it is same with new pin code. After all changed settings are finished, press OK key to save.

UNBlock ● Parental Control

Parental Control System Setting

● Confirm Password

EXIT

OK

● New Password

Main Menu

30 Digital Satellite Receiver SMP-6200 5.1.5.4 Timer This menu provides the users to record the programs they want to view.

01/05 THU 06:08 am Timer Lock . On

No. DAY START END CHANNEL DEST 01 WED 08 : 19 am 08 : 30 am 19,775 Mo TV 02 WED 03 : 36 am 03 : 38 am 2,715 Ph’ TV 03 M-F 03 : 38 am 03 : 41 am 3,721 Mov TV 04 WED 03 : 41 am 03 : 44 am 1,749 Sta TV 05 OFF 06 : 07 am 06 : 08 am TV 06 OFF 06 : 07 am 06 : 08 am TV 07 OFF 06 : 07 am 06 : 08 am TV

● Erase All Timers Move Save

● Timer Lock Exit EPG

The record event can be captured from the EPG event by pressing the EPG key from EPG MENU or users can input it manually.

1. Press RED key to erase all timers 2. Press BLUE key to lock the timer, every timer event can be run as scheduled correctly. 3. Press BLUE key twice to unlock the timer, if the timer lock is set to off, then all the timers will not work. 4. Press / key to move the event up/down or change the time values. 5. Press OK key to save the timer recording event and exit this menu. 6. Press EPG key to enter into EPG MENU. 7. Press EXIT directly to cancel the settings and exit this menu. Settings will not be saved.

5.1.5.5 Power up Channel This is to set the selected channel to be the power up channel.

Move Left/Right Exit TV/Radio Switch

Main Menu System Setting Timer

OK

OK

Main Menu System Setting Power Up Channel


OFF

EXIT

OK

EPG


1. Press / key to select the channel you want. 2. Press OK key to confirm this channel to be the power up channel, a confirmation message box will appear. 3. Select Yes to save or No to cancel. 4. Press TV/RADIO key to switch the channel list between TV and Radio.

5.1.6 System Information This menu provides the system information, including CA status, IRD status, Loader status, Mail Information, Announcement and Software Upgrade.

Move Select Exit

5.1.6.1 CA Status To view the status of CA system.

CA Module: Softcell: 2.26B SmartCard: Number: No Card Type: 0xffff Version: NONE State: 0xffff Transport Stream Information: TS1: EMM PID 0x1fff Service Information: E00 Service not scrambled Service Handle 1: 0x0000 Globe Service State: 0x000 Component Stream State: 00 00 00 Monitoring: EMM: 00 00 00 00 00 00 00 ECM: 00 00 00 00 00 00 00 00 00 00 00 00 Nationality:

Exit

Main Menu System Information

OK EXIT

Loader Status

CA Status

IRD Status

Announcement

Mail Information

Software Upgrade

Main Menu System Information CA Status

EXIT

32 Digital Satellite Receiver SMP-6200 5.1.6.2 IRD Status To view the system status.

IRD Smart Card 12121212 No Card IRD: 55 .5 .55 Firmware: None CA Module: Softcell: 2.26B Loader: 3.4 -1:0:27 OK L-17 OpenTV SW: None App SW: 2.0 Driver SW: v1.3 IRD SW: 8.16SMD5 Build Date: Jan 5 2006

Exit

5.1.6.3 Load Status To view the status of loader.

IRD Ser No.: 12121212 Loader Ver: 3.4 Manu Code: 55 H/W Ver: 5 Loader Seq: 17 Sig Ver: 27 Variant: 55 Key SysID: -1 Key Status: OK Key Ver: 0 Random No: 34343434 CRC Part: 30 Bin2IRD Ver: 3.1 m Bin2IRD Ser: 0001 Sign Date: 05/01/2006 Dload Date: 05/01/2006 Sign Time: 13:34:55 Image Size: 1214508 Dload Time: 13:35:15 Dload Dur: 00:02:43

Exit

Main Menu System Information IRD Status

EXIT

Main Menu System Information Loader Status

EXIT

33 Digital Satellite Receiver SMP-6200 5.1.6.4 Mail Information To view the mail content sent from head-end.

1. Press / key to wrap the mail. 2. Press Exit key to exit this menu. 3. Press Erase key to clear all the emails.

Page Exit ● Erase

5.1.6.5 Announcement To view the announcement content sent from head-end.

1. Press / key to wrap the announcement 2. Press Exit key to exit this menu. 3. Press Erase key to clear all announcements.

Page Exit ● Erase

5.1.6.6 Upgrade Software To download the new software from current satellite service. After pressing the “OK” key to download, the message shall be displayed on the screen. If any downloading service is found, the receiver will restart to download the new software. Note: Don’t power off the receiver or disconnect the satellite signal during software downloading process.

Main Menu System Information Mail Information

EXIT

Mail Message

This stream is scrambled. Num [1/8] Date

Main Menu System Information Announcement

Announcement

Softcell: ver 2.26B-Demux(SW CA). Complied Aug 10 2005 16:49:00

EXIT

34

Digital Satellite Receiver SMP-6200 6. SPECIFICATIONS

6.1 Compliance

This Digital Satellite Receiver meets the DVB-S/MPEG-2 standards for the reception of free-to-air digital satellite broadcast. It is compatible for SCPC/MCPC, C band, and Ku band signals. The menu of this receiver is designed such that the customer may set or change the channel frequency, symbol rate. This receiver can provide you with rich and abundant digital satellite TV programs.

6.2 Major Features - MPEG-2 (MP@ML) and DVB-S compatible - Enhanced OSD (On Screen Display) screen font - Storages of up to 3,000 channel data, 2,000 TV programs, and 1,000 radio programs - EPG (Electronic Program Guide) capability - The volume is adjustable - High-resolution picture quality and high fidelity stereo output - SAP (Second Audio Program) stereo capable - Capable of setting PID code to receive specified programs - Signal strength and quality display for convenient dish installation and/or adjustment - Software download capability via RS-232 port (optional) - Embedded Irdeto conditional access with smart card reader

Standards MPEG-2 DVB-S Tuner QPSK Symbol Rate 2 ~ 45 MSps Input Frequency Range 950 ~ 2150 MHz Input Signal Range -65 ~ -25 dBm Input Signal Terminal F-type Video Decoder Format MPEG-1, MPEG-2 Video Output Format PAL/NTSC (Automatic switching) Video Output Aspect Ratio 4:3, 16:9 and 4:3LB Video Output Resolution PAL (720x576), NTSC (720x480) Audio Decoder Format MPEG-1, MPEG-2 Audio Output Mode Single, Dual and Stereo Audio/Video Output Connectors 1 x RCA A/V LNB Polarization Voltage 13/18 Volts with Short-Circuit Protection LNB 22KHz Control ON / OFF, AUTO DiSEqC Version 1.2 Input Voltage 90-240 Volts, 50/60 Hz Power Consumption 30 Watts Dimensions 300mm (W) x 237mm (D) x 58mm (H)

35

DIGITAL SET-TOP-BOX

COPYRIGHT Home2US Communications, Inc.

irdeto ca satellite receiver - home2ushome2us.com/b2c/media/smp6200 user manual.pdf2 digital...

Documents