ipcop viking howto 02
TRANSCRIPT
-
7/29/2019 IPCop Viking Howto 02
1/11
IPCop / Viking PCI ADSL2+ Modem
PPPoE HOWTO
Author : Guy Ellis
Version : 0.2
Last Modified : 7/Nov/2008
-
7/29/2019 IPCop Viking Howto 02
2/11
Section 1 Initial IPCop Configuration
Firstly run setup on the IPCop console, or via SSH. Select the Networking option
Then select Network Configuration type
-
7/29/2019 IPCop Viking Howto 02
3/11
Set the configuration to Green + Red
Then from the Drivers and card assignment menu, select OK to change the settings
-
7/29/2019 IPCop Viking Howto 02
4/11
Select Probe
And assign to RED..
-
7/29/2019 IPCop Viking Howto 02
5/11
When complete select OK
Next select Address settings
-
7/29/2019 IPCop Viking Howto 02
6/11
Select the RED interface
And configure as shown
IMPORTANT : You must start with a Static setting to first configure the modem.After modem configuration is complete, then you must reconfigure for PPPoE or PPTP.
The initial configuration of IPCop is now complete, so exit the setup program.
-
7/29/2019 IPCop Viking Howto 02
7/11
Section 2 Modem CLI Configuration for PPPoE
The recommended modem configuration for PPPoE is bridged. In this case the modemsimply bridges the Ethernet packets to/from the ADSL line. Once bridging is configured on themodem, then IPCop is configured for PPPoE.
Using a telnet client on another machine on the green network, telnet to 192.168.1.1.The modem CLI (Command Line Interface) should appear
At the login prompt, login as admin / admin
Login: adminPassword: admin
Login successful
Next type the following commands to configure the modem
ip delete interface ipwan
bridge add interface br0
bridge attach br0 ethernet
rfc1483 add transport tr1 a1 8 35 llc bridged **{note the VPI, VCI values vary from country to country. 8, 35 as shown is for Australia. Forother countries refer to Appendix A}
bridge add interface br1
bridge attach br1 tr1
system config save
-
7/29/2019 IPCop Viking Howto 02
8/11
Section 3 IPCop configuration for PPPoE
Now that the modem has been configured, the last step is to configure IPCop for PPPoE.Run setup again from the IPCop console, or via SSH. Select the Networking option
Next select Address settings
-
7/29/2019 IPCop Viking Howto 02
9/11
Select the RED interface
And configure for PPPoE as shown
Select OK and exit setup.
-
7/29/2019 IPCop Viking Howto 02
10/11
Finally the IPCop dialup must be configured. From the IPCop web interface select NETWORK| DIALUP
Important settings :(i) Idle timeout = 0 (disabled)(ii) Connect on IPCop restart(iii) Reconnection = Persistant(iv) PPPoE plugin(v) Username is your username assigned by the ISP (normally the same as the email
address for that account)(vi) Password is your ISP/Connection password(vii) DNS = Automatic
Once PPPoE is configured, select save then return to the SYSTEM | HOME page and selectdial.
-
7/29/2019 IPCop Viking Howto 02
11/11
Appendix A - ADSL Protocols and PVCs(Vpi / Vci)
Country Provider ATMProtocol
VPI VCI
.au Telstra PPPoE, PPPoA 8 35
.au Nextep Bridged EthRFC1483.
1 32
Austria AON PPPoA 8 48.be Belgacom PPPoE
or Bridged Eth.RFC1483
8 35
.bh Batelco PPPoA 8 35
.es Routed IPRFC1483
8 32
.ch Sunrise andBluewin
PPPoE 8 35
.fr Wannadoo PPPoA orPPPoE
8 35
.nl PPPoA 8 48
.nz NZ Telecom PPPoA 0 100
.pt Portugal Telecom PPPoEor Bridged Eth.
RFC1483
0 35
.uk British Telecom PPPoA 0 38USA Bell South
Earthlink
PPPoA
PPPoE
8
0
35
35