ip conf param

WCDMA RAN and I-HSPA, Rel. RU30, Operating Documentation, Issue 07

IP Configuration Plan Interface Parameters

DN70257257

Issue 04FApproval Date 2011-11-25

Confidential

2 DN70257257Issue 04F


Id:0900d805809140a9Confidential

The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation.

The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given "as is" and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document.

Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTA-TION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDI-RECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT.

This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws.

The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG.

Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only.

Copyright © Nokia Siemens Networks 2011. All rights reserved

f Important Notice on Product SafetyThis product may present safety risks due to laser, electricity, heat, and other sources of danger.

Only trained and qualified personnel may install, operate, maintain or otherwise handle this product and only after having carefully read the safety information applicable to this product.

The safety information is provided in the Safety Information section in the “Legal, Safety and Environmental Information” part of this document or documentation set.

The same text in German:

f Wichtiger Hinweis zur Produktsicherheit Von diesem Produkt können Gefahren durch Laser, Elektrizität, Hitzeentwicklung oder andere Gefahrenquellen ausgehen.

Installation, Betrieb, Wartung und sonstige Handhabung des Produktes darf nur durch geschultes und qualifiziertes Personal unter Beachtung der anwendbaren Sicherheits-anforderungen erfolgen.

Die Sicherheitsanforderungen finden Sie unter „Sicherheitshinweise“ im Teil „Legal, Safety and Environmental Information“ dieses Dokuments oder dieses Dokumentations-satzes.

DN70257257 3



Table of contentsThis document has 216 pages.

1 Summary of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141.1 New Parameters in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Issue 04F141.2 Changed parameters in . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Issue 04F141.3 Removed Parameters in . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Issue 04F141.3.1 IBFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141.3.1.1 profileType (BFD Profile Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141.3.1.2 holdupTime (Holdup Time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141.3.2 IPRO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141.3.2.1 phbeBE (PHB BE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2 Introduction to IP configuration plan interface parameters . . . . . . . . . . 152.1 How to read parameter tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3 IAIF Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173.1 atmIfId (ATM interface id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173.2 atmIfNetId (IP over ATM interface id) . . . . . . . . . . . . . . . . . . . . . . . . . . 183.3 encapsulationMethod (Encapsulation method) . . . . . . . . . . . . . . . . . . . 193.4 type (Type). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193.5 usage (Usage) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203.6 vci (VCI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213.7 vpi (VPI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

4 IBFD Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244.1 alarmEnabled (Alarm enabled flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244.2 bfdEnabled (Bfd enabled flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244.3 bfdId (BFD session id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254.4 dstIp (Destination IP address) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264.5 ipbrId (Ip based route Id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274.6 profileId (Profile identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284.7 sessionType (Session Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294.8 srcIp (Source IP address) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

5 IBFP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315.1 desiredMinTx (Min transmission interval) . . . . . . . . . . . . . . . . . . . . . . . 315.2 detectMult (Detection multiplier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315.3 dscp (DSCP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325.4 profileId (IBFP identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335.5 profileName (Multi-Hop BFD Profile Name). . . . . . . . . . . . . . . . . . . . . . 345.6 requiredMinRx (Required minimum reception interval) . . . . . . . . . . . . . 35

6 IDNS Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 376.1 cache (Resolver Cache) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 376.2 iDNSId (DNS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386.3 localDomain (Local domain name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386.4 roundRobin (Round robin) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396.5 serverIPAddr (Server IP address list) . . . . . . . . . . . . . . . . . . . . . . . . . . 406.6 addrValue (Address value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

4 DN70257257



6.7 addrVer (IP address version for server IP address) . . . . . . . . . . . . . . . . 426.8 sortList (Network sortlist) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 436.9 addrValue (Address value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 446.10 netmask (Netmask). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

7 IDSP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 467.1 dscpProfileName (DSCP to PHB mapping ProfileName) . . . . . . . . . . . . 467.2 idspId (DSCP to PHB mapping profile Identifier) . . . . . . . . . . . . . . . . . . 477.3 profileList (Profile list) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 477.4 dscpNumber (Dscp Value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 487.5 phb (PHB value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

8 IEIF Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 518.1 IPV4Addr (IPv4 address list). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 518.2 addrTypeIPV4 (Address type IPv4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 518.3 addrValueIPV4 (IP address IPv4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 528.4 destAddrIPV4 (Destination address IPv4) . . . . . . . . . . . . . . . . . . . . . . . 538.5 netmask (Netmask). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 548.6 administrativeState (Administrative state). . . . . . . . . . . . . . . . . . . . . . . . 558.7 ethIfNetId (Ethernet Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . 568.8 ifType (Interface type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 578.9 mtu (Maximum Transfer Unit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

9 IGIF Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 609.1 RncEthernetBw (EthernetBw) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 609.2 ethInterfaceRate (Ethernet interface rate) . . . . . . . . . . . . . . . . . . . . . . . 609.3 igifId (Ethernet Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

10 IICP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6310.1 echoReplyTmout (Timeout for echo reply re-ceiving) . . . . . . . . . . . . . . . 6310.2 echoReqPeriod (Period for echo request packet sending) . . . . . . . . . . . 6310.3 maxLostPkt (maxLostPkt) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6410.4 payloadLength (payloadLength) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6510.5 profileId (IICP identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

11 IOAM Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6811.1 InstanceID (Ethernet OAM Instance ID) . . . . . . . . . . . . . . . . . . . . . . . . . 6811.2 activeMode (Link OAM working Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . 6911.3 adminState (Link OAM Administration State ) . . . . . . . . . . . . . . . . . . . 6911.4 almClrTimer (Link OAM Critical Event Alarm Clearance Timer) . . . . . . . 7011.5 efEvtThd (Link OAM Error Frame Event Threshold) . . . . . . . . . . . . . . . . 7111.6 efEvtWnd (Link OAM Error Frame Event Window). . . . . . . . . . . . . . . . . 7211.7 efSecThd (Link OAM Error Frame Seconds Threshold) . . . . . . . . . . . . . 7311.8 efSecWnd (Link OAM Error Frame Seconds Window) . . . . . . . . . . . . . . 7411.9 lostTimer (Ethernet OAM Link Timeout) . . . . . . . . . . . . . . . . . . . . . . . . . 7511.10 lpDuration (Link OAM Loopback Duration Time) . . . . . . . . . . . . . . . . . . 7611.11 lpLostTimer (Link OAM Loopback Timeout) . . . . . . . . . . . . . . . . . . . . . . 7711.12 lpPktRate (Link OAM Loopback Packet Rate) . . . . . . . . . . . . . . . . . . . . 7811.13 lpPktSize (Link OAM Loopback Packet Size ) . . . . . . . . . . . . . . . . . . . . 7911.14 pduTimer (Link OAM PDU Timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

DN70257257 5



11.15 templateID (Template ID). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

12 IOAMT Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8312.1 almClrTimer (Link OAM Critical Event Alarm Clearance Timer) . . . . . . 8312.2 efEvtThd (Link OAM Error Frame Event Threshold) . . . . . . . . . . . . . . . 8312.3 efEvtWnd (Link OAM Error Frame Event Window) . . . . . . . . . . . . . . . . 8412.4 efSecThd (Link OAM Error Frame Seconds Threshold ) . . . . . . . . . . . . 8512.5 efSecWnd (Link OAM Error Frame Seconds Window) . . . . . . . . . . . . . 8612.6 lostTimer (Ethernet OAM Link Timeout) . . . . . . . . . . . . . . . . . . . . . . . . 8712.7 lpDuration (Link OAM Loopback Duration Time) . . . . . . . . . . . . . . . . . . 8812.8 lpLostTimer (Link OAM Loopback Timeout) . . . . . . . . . . . . . . . . . . . . . 8912.9 lpPktRate (Link OAM Loopback Packet Rate) . . . . . . . . . . . . . . . . . . . . 9012.10 lpPktSize (Link OAM Loopback Packet Size) . . . . . . . . . . . . . . . . . . . . 9012.11 pduTimer (Link OAM PDU Timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9112.12 templateID (Template ID). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9212.13 templateName (Ethernet OAM Template Name). . . . . . . . . . . . . . . . . . 93

13 IOPF Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9513.1 iopfId (IOPF Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9513.2 rfc1583comp (RFC1583 Compatibility) . . . . . . . . . . . . . . . . . . . . . . . . . 9513.3 routeId (Router Id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9613.4 spfDelay (SPF Delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9713.5 spfHoldtime (SPF Holdtime) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

14 IPBR Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10014.1 committedBW (Committed BW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10014.2 committedDcnBW (Committed DCN BW). . . . . . . . . . . . . . . . . . . . . . 10014.3 committedSigBW (Committed signal BW ) . . . . . . . . . . . . . . . . . . . . . 10114.4 ifcFlag (IP IFC Flag). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10214.5 ipBasedRouteName (IP based route name) . . . . . . . . . . . . . . . . . . . . 10314.6 ipbrId (IP based route id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10414.7 localMuxUDPPort (IP multiplexing local UDP port) . . . . . . . . . . . . . . . 10514.8 maxMuxPackets (IP multiplexing max packets). . . . . . . . . . . . . . . . . . 10614.9 ratio (Ratio ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10614.10 remoteMuxUDPPort (IP multiplexing remote UDP port) . . . . . . . . . . . 10714.11 routeBW (Route bandwidth). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10814.12 udpMuxDSCP (IP multiplexing DSCP value). . . . . . . . . . . . . . . . . . . . 10914.13 udpMuxEnabled (IP multiplexing flag) . . . . . . . . . . . . . . . . . . . . . . . . . 110

15 IPHB Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11115.1 phbId (PHB profile Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11115.2 phbProfileName (PHB profile name) . . . . . . . . . . . . . . . . . . . . . . . . . . 11215.3 profileList (PHB Profile List) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11215.4 expWeig (Exponential weight factor) . . . . . . . . . . . . . . . . . . . . . . . . . . 11315.5 length (Queue length) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11415.6 maxDrop (Max drop value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11515.7 maxThreshold (Max threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11615.8 minThreshold (Min threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11715.9 phb (PHB value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118

6 DN70257257



15.10 quePriority (Queue priority). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11915.11 queWeight (Queue weight) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11915.12 schedule (Queue schedule) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12015.13 vlanPri (Vlan priority). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

16 IPNO Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12316.1 IPForwardingIPV4 (IP Forwarding flag) . . . . . . . . . . . . . . . . . . . . . . . . 12316.2 defaultTTL (Default TTL). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12416.3 hostName (Host name). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12416.4 ipNodeId (IP Node Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12516.5 subnetsAreLocal (Subnets are local) . . . . . . . . . . . . . . . . . . . . . . . . . . 126

17 IPRO Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12817.1 ipBasedRoute (IP based route Entries) . . . . . . . . . . . . . . . . . . . . . . . . 12817.2 addrValueIPV4 (IP address ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12917.3 ipBasedRouteId (IP based route id) . . . . . . . . . . . . . . . . . . . . . . . . . . . 12917.4 phbAF1 (PHB AF1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13017.5 phbAF2 (PHB AF2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13117.6 phbAF3 (PHB AF3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13317.7 phbAF4 (PHB AF4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13417.8 phbEF (PHB EF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13517.9 iproId (network interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13617.10 iproListMode (IP Based Route id list update mode) . . . . . . . . . . . . . . . 137

18 IPRT Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14018.1 ipRoutingTableId (IP Routing Table Identifier) . . . . . . . . . . . . . . . . . . . 14018.2 iprtListMode (IP static route list update mode) . . . . . . . . . . . . . . . . . . . 14118.3 routeEntriesIPV4 (Route Entries for IPv4) . . . . . . . . . . . . . . . . . . . . . . 14218.4 bfdId (BFD session ID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14318.5 destIPAddrIPV4 (Destination IPv4 address) . . . . . . . . . . . . . . . . . . . . . 14418.6 gatewayIPV4 (Gateway IPv4 address) . . . . . . . . . . . . . . . . . . . . . . . . . 14518.7 netmask (Netmask). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14618.8 preference (Preference) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14718.9 routeType (Route type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14718.10 srcIPAddrIPV4 (Source IPv4 address) . . . . . . . . . . . . . . . . . . . . . . . . . 148

19 IQOS Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15019.1 dspmProfileId (DSPM profile id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15019.2 dspmProfileName (DSPM profile name). . . . . . . . . . . . . . . . . . . . . . . . 15019.3 iqosId (Qos interface) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15119.4 phbProfileId (PHB profile id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15219.5 phbProfileName (PHB profile name). . . . . . . . . . . . . . . . . . . . . . . . . . . 15319.6 status (Status) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154

20 ISBFP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15620.1 desiredMinTx (Min transmission interval) . . . . . . . . . . . . . . . . . . . . . . . 15620.2 detectMult (Detection multiplier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15620.3 dscp (DSCP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15720.4 holdupTime (Holdup Time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15820.5 profileId (ISBFP identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159

DN70257257 7



20.6 profileName (Single-hop BFD Profile Name) . . . . . . . . . . . . . . . . . . . . 16020.7 requiredMinRx (Required minimum reception interval) . . . . . . . . . . . . 161

21 ISPF Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16221.1 areaId (Area Identification) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16221.2 interfaceEntries (Interface Entries) . . . . . . . . . . . . . . . . . . . . . . . . . . . 16221.3 cost (Cost) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16321.4 deadInterval (Dead Interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16421.5 helloInterval (Hello Interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16521.6 interfaceName (Interface Name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16621.7 passive (Passive). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16721.8 password (Password) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16821.9 priority (Priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16921.10 type (Type). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17021.11 ispfId (ISPF Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17121.12 networkPrefixEntries (Network Prefix Entries) . . . . . . . . . . . . . . . . . . . 17121.13 maskLength (Mask Length) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17221.14 networkPrefix (Network Prefix) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17321.15 restriction (Restriction) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17421.16 networkStubEntries (Network Stub Entries). . . . . . . . . . . . . . . . . . . . . 17521.17 cost (Cost) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17621.18 stubNetwork (Stub Network) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17721.19 stubPrefixLength (stub netmask ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17721.20 routeCost (Route Cost) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17821.21 stubArea (Stub Area) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17921.22 stubbyArea (Stubby Area) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18021.23 virLinkEntries (Virtual Link Entries) . . . . . . . . . . . . . . . . . . . . . . . . . . . 18121.24 deadInterval (Dead Interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18221.25 helloInterval (Hello Interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18321.26 password (Password) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18421.27 remoteRouteId (Remote Route Id). . . . . . . . . . . . . . . . . . . . . . . . . . . . 18421.28 type (type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185

22 ISPRT Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18722.1 interfaceEntries (Interface Entries) . . . . . . . . . . . . . . . . . . . . . . . . . . . 18722.2 ifName (Interface Name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18722.3 metric (Metric) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18822.4 isprtId (ISPRT identifier). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18922.5 redistAllEntries (Redistribute Entries) . . . . . . . . . . . . . . . . . . . . . . . . . 19022.6 metric (Metric) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19122.7 type (Type). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19122.8 routeEntries (Route Entries) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19222.9 destIPAddrIPV4 (DestIPAddrIPV4) . . . . . . . . . . . . . . . . . . . . . . . . . . . 19322.10 gatewayIPV4 (GatewayIPV4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19422.11 metric (Metric) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19522.12 netmask (Netmask) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196

23 ITRKGRP Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19723.1 trkGrpBoolVal (Network Status Tracker Group Operation Bool Value) 197

8 DN70257257



23.2 trkGrpId (Network Status Tracker Group ID) . . . . . . . . . . . . . . . . . . . . 19823.3 trkGrpOperation (Network Status Tracker Group Operation) . . . . . . . . 19923.4 trkGrpWeightVal (Network Status Tracker Group Operation Weight Value)

20023.5 trkType (Network Status Tracker Group Type) . . . . . . . . . . . . . . . . . . . 201

24 ITRKOBJ Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20224.1 trkObjName (Network Status Tracker Object Name) . . . . . . . . . . . . . . 20224.2 trkObjWeight (Network Status Tracker Object Weight). . . . . . . . . . . . . 203

25 IUBSNT Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20425.1 IPV4MaskLength (IPV4 mask length) . . . . . . . . . . . . . . . . . . . . . . . . . . 20425.2 IPV4SubnetAddress (IPV4 subnet address). . . . . . . . . . . . . . . . . . . . . 20425.3 assocMaxRetrans (Association max retrans) . . . . . . . . . . . . . . . . . . . . 20525.4 hbInterval (HB interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20625.5 iubsntId (Iubsnt Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20725.6 maxInitRetrans (MaxInitRetrans) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20825.7 pathMaxRetrans (PathMaxRetrans) . . . . . . . . . . . . . . . . . . . . . . . . . . . 20925.8 rtoInitial (RTO Initial) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20925.9 rtoMax (RTO Max) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21025.10 rtoMin (RTO Min) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21125.11 sackPeriod (sackPeriod) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21225.12 validCookieLife (Valid Cookie Life) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213

26 IVIF Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21426.1 parentInterface (Vlan physical Interface) . . . . . . . . . . . . . . . . . . . . . . . 21426.2 vid (Vlan id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21426.3 vlanIfId (Vlan Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215

DN70257257 9



List of tablesTable 1 How to read parameter tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Table 2 atmIfId (ATM interface id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Table 3 atmIfNetId (IP over ATM interface id) . . . . . . . . . . . . . . . . . . . . . . . . . . 18Table 4 encapsulationMethod (Encapsulation method) . . . . . . . . . . . . . . . . . . . 19Table 5 type (Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Table 6 usage (Usage) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Table 7 vci (VCI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Table 8 vpi (VPI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Table 9 alarmEnabled (Alarm enabled flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Table 10 bfdEnabled (Bfd enabled flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Table 11 bfdId (BFD session id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Table 12 dstIp (Destination IP address) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Table 13 ipbrId (Ip based route Id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Table 14 profileId (Profile identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Table 15 sessionType (Session Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Table 16 srcIp (Source IP address) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Table 17 desiredMinTx (Min transmission interval) . . . . . . . . . . . . . . . . . . . . . . 31Table 18 detectMult (Detection multiplier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Table 19 dscp (DSCP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Table 20 profileId (IBFP identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Table 21 profileName (Multi-Hop BFD Profile Name) . . . . . . . . . . . . . . . . . . . . . 34Table 22 requiredMinRx (Required minimum reception interval) . . . . . . . . . . . . . 35Table 23 cache (Resolver Cache) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Table 24 iDNSId (DNS Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Table 25 localDomain (Local domain name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Table 26 roundRobin (Round robin) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39Table 27 serverIPAddr (Server IP address list) . . . . . . . . . . . . . . . . . . . . . . . . . . 40Table 28 addrValue (Address value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41Table 29 addrVer (IP address version for server IP address) . . . . . . . . . . . . . . . 42Table 30 sortList (Network sortlist) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Table 31 addrValue (Address value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Table 32 netmask (Netmask) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Table 33 dscpProfileName (DSCP to PHB mapping ProfileName) . . . . . . . . . . . 46Table 34 idspId (DSCP to PHB mapping profile Identifier) . . . . . . . . . . . . . . . . . 47Table 35 profileList (Profile list) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47Table 36 dscpNumber (Dscp Value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Table 37 phb (PHB value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Table 38 IPV4Addr (IPv4 address list) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51Table 39 addrTypeIPV4 (Address type IPv4) . . . . . . . . . . . . . . . . . . . . . . . . . . . 51Table 40 addrValueIPV4 (IP address IPv4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Table 41 destAddrIPV4 (Destination address IPv4) . . . . . . . . . . . . . . . . . . . . . . 53Table 42 netmask (Netmask) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Table 43 administrativeState (Administrative state) . . . . . . . . . . . . . . . . . . . . . . . 55Table 44 ethIfNetId (Ethernet Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . 56Table 45 ifType (Interface type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

10 DN70257257



Table 46 mtu (Maximum Transfer Unit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58Table 47 RncEthernetBw (EthernetBw) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60Table 48 ethInterfaceRate (Ethernet interface rate) . . . . . . . . . . . . . . . . . . . . . . . 60Table 49 igifId (Ethernet Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61Table 50 echoReplyTmout (Timeout for echo reply re-ceiving) . . . . . . . . . . . . . . 63Table 51 echoReqPeriod (Period for echo request packet sending) . . . . . . . . . . 63Table 52 maxLostPkt (maxLostPkt) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64Table 53 payloadLength (payloadLength) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65Table 54 profileId (IICP identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66Table 55 InstanceID (Ethernet OAM Instance ID) . . . . . . . . . . . . . . . . . . . . . . . . 68Table 56 activeMode (Link OAM working Mode) . . . . . . . . . . . . . . . . . . . . . . . . . 69Table 57 adminState (Link OAM Administration State ) . . . . . . . . . . . . . . . . . . . 69Table 58 almClrTimer (Link OAM Critical Event Alarm Clearance Timer) . . . . . . 70Table 59 efEvtThd (Link OAM Error Frame Event Threshold) . . . . . . . . . . . . . . . 71Table 60 efEvtWnd (Link OAM Error Frame Event Window) . . . . . . . . . . . . . . . . 72Table 61 efSecThd (Link OAM Error Frame Seconds Threshold) . . . . . . . . . . . . 73Table 62 efSecWnd (Link OAM Error Frame Seconds Window) . . . . . . . . . . . . . 74Table 63 lostTimer (Ethernet OAM Link Timeout) . . . . . . . . . . . . . . . . . . . . . . . . 75Table 64 lpDuration (Link OAM Loopback Duration Time) . . . . . . . . . . . . . . . . . . 76Table 65 lpLostTimer (Link OAM Loopback Timeout) . . . . . . . . . . . . . . . . . . . . . 77Table 66 lpPktRate (Link OAM Loopback Packet Rate) . . . . . . . . . . . . . . . . . . . . 78Table 67 lpPktSize (Link OAM Loopback Packet Size ) . . . . . . . . . . . . . . . . . . . . 79Table 68 pduTimer (Link OAM PDU Timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80Table 69 templateID (Template ID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81Table 70 almClrTimer (Link OAM Critical Event Alarm Clearance Timer) . . . . . . 83Table 71 efEvtThd (Link OAM Error Frame Event Threshold) . . . . . . . . . . . . . . . 83Table 72 efEvtWnd (Link OAM Error Frame Event Window) . . . . . . . . . . . . . . . . 84Table 73 efSecThd (Link OAM Error Frame Seconds Threshold ) . . . . . . . . . . . . 85Table 74 efSecWnd (Link OAM Error Frame Seconds Window) . . . . . . . . . . . . . 86Table 75 lostTimer (Ethernet OAM Link Timeout) . . . . . . . . . . . . . . . . . . . . . . . . 87Table 76 lpDuration (Link OAM Loopback Duration Time) . . . . . . . . . . . . . . . . . . 88Table 77 lpLostTimer (Link OAM Loopback Timeout) . . . . . . . . . . . . . . . . . . . . . 89Table 78 lpPktRate (Link OAM Loopback Packet Rate) . . . . . . . . . . . . . . . . . . . . 90Table 79 lpPktSize (Link OAM Loopback Packet Size) . . . . . . . . . . . . . . . . . . . . 90Table 80 pduTimer (Link OAM PDU Timer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91Table 81 templateID (Template ID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92Table 82 templateName (Ethernet OAM Template Name) . . . . . . . . . . . . . . . . . . 93Table 83 iopfId (IOPF Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95Table 84 rfc1583comp (RFC1583 Compatibility) . . . . . . . . . . . . . . . . . . . . . . . . . 95Table 85 routeId (Router Id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96Table 86 spfDelay (SPF Delay) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97Table 87 spfHoldtime (SPF Holdtime) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98Table 88 committedBW (Committed BW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100Table 89 committedDcnBW (Committed DCN BW) . . . . . . . . . . . . . . . . . . . . . . 100Table 90 committedSigBW (Committed signal BW ) . . . . . . . . . . . . . . . . . . . . . 101Table 91 ifcFlag (IP IFC Flag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102Table 92 ipBasedRouteName (IP based route name) . . . . . . . . . . . . . . . . . . . . 103

DN70257257 11



Table 93 ipbrId (IP based route id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104Table 94 localMuxUDPPort (IP multiplexing local UDP port) . . . . . . . . . . . . . . . 105Table 95 maxMuxPackets (IP multiplexing max packets) . . . . . . . . . . . . . . . . . 106Table 96 ratio (Ratio ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106Table 97 remoteMuxUDPPort (IP multiplexing remote UDP port) . . . . . . . . . . . 107Table 98 routeBW (Route bandwidth) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108Table 99 udpMuxDSCP (IP multiplexing DSCP value) . . . . . . . . . . . . . . . . . . . 109Table 100 udpMuxEnabled (IP multiplexing flag) . . . . . . . . . . . . . . . . . . . . . . . . 110Table 101 phbId (PHB profile Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111Table 102 phbProfileName (PHB profile name) . . . . . . . . . . . . . . . . . . . . . . . . . . 112Table 103 profileList (PHB Profile List) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112Table 104 expWeig (Exponential weight factor) . . . . . . . . . . . . . . . . . . . . . . . . . 113Table 105 length (Queue length) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114Table 106 maxDrop (Max drop value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115Table 107 maxThreshold (Max threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116Table 108 minThreshold (Min threshold) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117Table 109 phb (PHB value) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118Table 110 quePriority (Queue priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119Table 111 queWeight (Queue weight) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119Table 112 schedule (Queue schedule) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120Table 113 vlanPri (Vlan priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121Table 114 IPForwardingIPV4 (IP Forwarding flag) . . . . . . . . . . . . . . . . . . . . . . . 123Table 115 defaultTTL (Default TTL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124Table 116 hostName (Host name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124Table 117 ipNodeId (IP Node Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125Table 118 subnetsAreLocal (Subnets are local) . . . . . . . . . . . . . . . . . . . . . . . . . 126Table 119 ipBasedRoute (IP based route Entries) . . . . . . . . . . . . . . . . . . . . . . . 128Table 120 addrValueIPV4 (IP address ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129Table 121 ipBasedRouteId (IP based route id) . . . . . . . . . . . . . . . . . . . . . . . . . . 129Table 122 phbAF1 (PHB AF1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130Table 123 phbAF2 (PHB AF2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131Table 124 phbAF3 (PHB AF3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133Table 125 phbAF4 (PHB AF4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134Table 126 phbEF (PHB EF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135Table 127 iproId (network interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . 136Table 128 iproListMode (IP Based Route id list update mode) . . . . . . . . . . . . . . 137Table 129 ipRoutingTableId (IP Routing Table Identifier) . . . . . . . . . . . . . . . . . . 140Table 130 iprtListMode (IP static route list update mode) . . . . . . . . . . . . . . . . . . 141Table 131 routeEntriesIPV4 (Route Entries for IPv4) . . . . . . . . . . . . . . . . . . . . . 142Table 132 bfdId (BFD session ID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143Table 133 destIPAddrIPV4 (Destination IPv4 address) . . . . . . . . . . . . . . . . . . . . 144Table 134 gatewayIPV4 (Gateway IPv4 address) . . . . . . . . . . . . . . . . . . . . . . . . 145Table 135 netmask (Netmask) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146Table 136 preference (Preference) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147Table 137 routeType (Route type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147Table 138 srcIPAddrIPV4 (Source IPv4 address) . . . . . . . . . . . . . . . . . . . . . . . . 148Table 139 dspmProfileId (DSPM profile id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150

12 DN70257257



Table 140 dspmProfileName (DSPM profile name) . . . . . . . . . . . . . . . . . . . . . . . 150Table 141 iqosId (Qos interface) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151Table 142 phbProfileId (PHB profile id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152Table 143 phbProfileName (PHB profile name) . . . . . . . . . . . . . . . . . . . . . . . . . . 153Table 144 status (Status) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154Table 145 desiredMinTx (Min transmission interval) . . . . . . . . . . . . . . . . . . . . . . 156Table 146 detectMult (Detection multiplier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156Table 147 dscp (DSCP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157Table 148 holdupTime (Holdup Time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158Table 149 profileId (ISBFP identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159Table 150 profileName (Single-hop BFD Profile Name) . . . . . . . . . . . . . . . . . . . . 160Table 151 requiredMinRx (Required minimum reception interval) . . . . . . . . . . . . 161Table 152 areaId (Area Identification) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162Table 153 interfaceEntries (Interface Entries) . . . . . . . . . . . . . . . . . . . . . . . . . . . 162Table 154 cost (Cost) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163Table 155 deadInterval (Dead Interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164Table 156 helloInterval (Hello Interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165Table 157 interfaceName (Interface Name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166Table 158 passive (Passive) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167Table 159 password (Password) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168Table 160 priority (Priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169Table 161 type (Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170Table 162 ispfId (ISPF Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171Table 163 networkPrefixEntries (Network Prefix Entries) . . . . . . . . . . . . . . . . . . . 171Table 164 maskLength (Mask Length) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172Table 165 networkPrefix (Network Prefix) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173Table 166 restriction (Restriction) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174Table 167 networkStubEntries (Network Stub Entries) . . . . . . . . . . . . . . . . . . . . . 175Table 168 cost (Cost) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176Table 169 stubNetwork (Stub Network) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177Table 170 stubPrefixLength (stub netmask ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177Table 171 routeCost (Route Cost) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178Table 172 stubArea (Stub Area) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179Table 173 stubbyArea (Stubby Area) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180Table 174 virLinkEntries (Virtual Link Entries) . . . . . . . . . . . . . . . . . . . . . . . . . . . 181Table 175 deadInterval (Dead Interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182Table 176 helloInterval (Hello Interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183Table 177 password (Password) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184Table 178 remoteRouteId (Remote Route Id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184Table 179 type (type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185Table 180 interfaceEntries (Interface Entries) . . . . . . . . . . . . . . . . . . . . . . . . . . . 187Table 181 ifName (Interface Name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187Table 182 metric (Metric) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188Table 183 isprtId (ISPRT identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189Table 184 redistAllEntries (Redistribute Entries) . . . . . . . . . . . . . . . . . . . . . . . . . 190Table 185 metric (Metric) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191Table 186 type (Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191

DN70257257 13



Table 187 routeEntries (Route Entries) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192Table 188 destIPAddrIPV4 (DestIPAddrIPV4) . . . . . . . . . . . . . . . . . . . . . . . . . . . 193Table 189 gatewayIPV4 (GatewayIPV4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194Table 190 metric (Metric) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195Table 191 netmask (Netmask) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196Table 192 trkGrpBoolVal (Network Status Tracker Group Operation Bool Value) 197Table 193 trkGrpId (Network Status Tracker Group ID) . . . . . . . . . . . . . . . . . . . 198Table 194 trkGrpOperation (Network Status Tracker Group Operation) . . . . . . . 199Table 195 trkGrpWeightVal (Network Status Tracker Group Operation Weight Value)

200Table 196 trkType (Network Status Tracker Group Type) . . . . . . . . . . . . . . . . . . 201Table 197 trkObjName (Network Status Tracker Object Name) . . . . . . . . . . . . . 202Table 198 trkObjWeight (Network Status Tracker Object Weight) . . . . . . . . . . . . 203Table 199 IPV4MaskLength (IPV4 mask length) . . . . . . . . . . . . . . . . . . . . . . . . . 204Table 200 IPV4SubnetAddress (IPV4 subnet address) . . . . . . . . . . . . . . . . . . . . 204Table 201 assocMaxRetrans (Association max retrans) . . . . . . . . . . . . . . . . . . . 205Table 202 hbInterval (HB interval) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206Table 203 iubsntId (Iubsnt Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207Table 204 maxInitRetrans (MaxInitRetrans) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208Table 205 pathMaxRetrans (PathMaxRetrans) . . . . . . . . . . . . . . . . . . . . . . . . . . 209Table 206 rtoInitial (RTO Initial) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209Table 207 rtoMax (RTO Max) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210Table 208 rtoMin (RTO Min) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211Table 209 sackPeriod (sackPeriod) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212Table 210 validCookieLife (Valid Cookie Life) . . . . . . . . . . . . . . . . . . . . . . . . . . . 213Table 211 parentInterface (Vlan physical Interface) . . . . . . . . . . . . . . . . . . . . . . 214Table 212 vid (Vlan id) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214Table 213 vlanIfId (Vlan Interface Identifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215

14 DN70257257


Id:0900d805808e2b75Confidential

Summary of changes

1 Summary of changesChanges between document issues are cumulative. Therefore, the latest document issue contains all changes made to previous issues.

Changes between Issue 04E (2011-09-16, RU30) and Issue 04F (2011-11-25, RU30).

1.1 New Parameters in Issue 04FThere are no new parameters.

1.2 Changed parameters in Issue 04FThere are no changed parameters.

1.3 Removed Parameters in Issue 04F

1.3.1 IBFP

1.3.1.1 profileType (BFD Profile Type)

1.3.1.2 holdupTime (Holdup Time)

1.3.2 IPRO

1.3.2.1 phbeBE (PHB BE)

DN70257257 15

IP Configuration Plan Interface Parameters Introduction to IP configuration plan interface parame-ters


2 Introduction to IP configuration plan inter-face parametersThe purpose of this document is to assist RNC and NetAct users to find IP configuration plan interface parameters, their meanings, specifications, and default values. The managed objects and parameters are represented in an alphabetical order.

The plan-based RNC IP configuration feature introduces the configuration management interface between the RNC and NetAct. The object model and the attributes applied in the plan interface follow the generic NWI3 presentation that is also used in other Nokia Siemens Networks RAN network elements.

2.1 How to read parameter tables

Entry Description

Parameter name The user interface name for the parameter

Abbreviated name The parameter name used in XML and CSV plan files

3GPP name The used parameter name in 3GPP specifications

Managed object The object for which the parameter is defined

Parameter group The functional group which the parameter belongs to

Category The parameters are classified into the following categories:

• Operation and Maintenance • Performance Management • Radio Resource Utilisation • Telecom • Transmission

Multiplicity The multiplicity of the parameter

Description Describes the purpose of the parameter and sometimes includes extra information on the parameter

Range The user interface value range for the parameter

Step The value by which the parameter value increases or decreases within the range

Unit The measurement unit in use for the range and step, for example,

s (seconds), min (minutes), h (hour), m (meters), km (kilometers),

dBm (decibelmeter), dB (decibel), bits (bit per second),

kbit/s (kilobits per second), % (percent), per mil (per mille), period;

if no unit indicator is given, it means that the value range has no measurement unit or the parameter has no step

Formula for getting internal value

The formula for calculating the system internal value which is used within the system

Default value Nokia Siemens Networks specified default value

Table 1 How to read parameter tables

16 DN70257257



Introduction to IP configuration plan interface parame-ters

Default value notes Additional information (if any) on the default value

Related functions Radio-network-related functions (in addition to the main function) of the parameter

System information Accurate System information block which parameters send to a mobile

Modification Requires object locking =The managed object must be locked by the user before the modification is possible.

Not modifiable =The parameter value can be modified only through recreation of the managed object.

Online = The parameter value can be changed without any disturbance to ongoing calls

Related parameters Other parameters that affect the parameter

Parameter relationship Dependencies between the parameter and the related parameters

Related features Features associated with the parameter

Interface Information on which interfaces the parameter is transferred

References References (if any) to 3GPP specifications

Entry Description

Table 1 How to read parameter tables (Cont.)

DN70257257 17

IP Configuration Plan Interface Parameters IAIF Parameters


3 IAIF Parameters

3.1 atmIfId (ATM interface id)

Parameter name ATM interface id

Abbreviated name atmIfId

3GPP name -

Managed Object IAIF

Parameter group -

Classification -

Multiplicity 1

Description This parameter identifies the associated ATM interface. The whole triplet ATM if, VPI, VCI needs to be given.

The related ATM layer object in RNC MML: VCLtp (ZLC)

The related ATM plan managed object: TCTT

The corresponding MML command group: ZQM, "ATM interface".

Range 1... 588

Step 1

Units -


internal_value = gui_value

Default value -

Default value notes Default value is not possible

Related functions -

Modification Not modifiable

Related parameters -

Parameter relationships -

Related options -

Feature dependencies -

Interfaces • RNC <-> RAC • RAC <-> RACApp

References -

Table 2 atmIfId (ATM interface id)

18 DN70257257



IAIF Parameters

3.2 atmIfNetId (IP over ATM interface id)

Parameter name IP over ATM interface id

Abbreviated name atmIfNetId

3GPP name -

Managed Object IAIF

Parameter group -

Classification -

Multiplicity 1

Description This parameter identifies the IP over ATM interface

in the system.

For OMU and GTPU, the interface id is AA0-AA511.

For ICSU, the interface id is AA0-AA449.

For NPS1(P), the interface id is IFAE0-IFAE1399.

The identifier is part of the distinguished

name and is formed in the following way:

NE-x/IPNO-unitType-unitIndex/IAIF-ifName. For

example: RNC-1/IPNO-OMU-0/IAIF-AA0.

The corresponding MML command: ZQMF,"IP interface".

Range 1...32

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 3 atmIfNetId (IP over ATM interface id)

DN70257257 19



3.3 encapsulationMethod (Encapsulation method)

3.4 type (Type)

Parameter name Encapsulation method

Abbreviated name encapsulationMethod

3GPP name -

Managed Object IAIF

Parameter group -

Classification -

Multiplicity 1

Description This parameter identifies the encapsulation method. The value is either LLC/SNAP or VCMUX.

The corresponding MML command group: ZQM, "encapsulation method".

Range LLC/SNAP (0), VCMUX (1)

Step -

Units -


gui ==> internal

LLC/SNAP ==> 0

VCMUX ==> 1

Default value LLC/SNAP (0)

Default value notes -

Related functions -




Related options -



References -

Table 4 encapsulationMethod (Encapsulation method)

Parameter name Type

Abbreviated name type

3GPP name -

Table 5 type (Type)

20 DN70257257



IAIF Parameters

3.5 usage (Usage)

Managed Object IAIF

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines whether IPoA is terminated to the logical or physical address type of the unit. The possible parameter value is "L" for logical address type only.

The corresponding MML command group: ZQM, "interface type".

Range Logical (1)

Step -

Units -


gui ==> internal

Logical ==> 1

Default value Logical (1)


Related functions -




Related options -



References -

Table 5 type (Type) (Cont.)

Parameter name Usage

Abbreviated name usage

3GPP name -

Managed Object IAIF

Parameter group -

Classification -

Multiplicity 1

Table 6 usage (Usage)

DN70257257 21



3.6 vci (VCI)

Description This parameter identifies the usage of the connection.

The value can be IPOAUD, IPOART,IPOAM,or IPCONN . This parameter identifies the usage of connection. The value can be IPOAUD, or IPOAM

for OMU, RSMU, ICSU and GTPU units, and the default value is IPOAM. For NPS1(P)

units, the value is IPCONN.

Note:

The value IPOART is available only if the feature

'Streaming packet switched QoS' is in use, otherwise

it is restricted.

The corresponding MML command group: ZQM,

"usage".

Range IPOAUD (0), IPOART (1), IPOAM (2), IPCONN (3)

Step -

Units -


gui ==> internal

IPOAUD ==> 0

IPOART ==> 1

IPOAM ==> 2

IPCONN ==> 3

Default value -

Default value notes IPCONN (3) is for NPS1(P),and IPOAM (2) is for other units.

Related functions -




Related options -



References -

Table 6 usage (Usage) (Cont.)

Parameter name VCI

Abbreviated name vci

Table 7 vci (VCI)

22 DN70257257



IAIF Parameters

3.7 vpi (VPI)

3GPP name -

Managed Object IAIF

Parameter group -

Classification -

Multiplicity 1

Description This parameter identifies the associated VCI within the VPI. The whole triplet ATM if, VPI, VCI needs to be given.

The related ATM layer object in RNC MML: VCLtp (ZLC command group).

The related ATM plan managed object: VCCT object id.

The corresponding MML command group: ZQM, "VCI number".

Range 1... 65535

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 7 vci (VCI) (Cont.)

Parameter name VPI

Abbreviated name vpi

3GPP name -

Managed Object IAIF

Parameter group -

Classification -

Table 8 vpi (VPI)

DN70257257 23



Multiplicity 1

Description This parameter identifies the associated VPI within the ATM interface. The whole triplet ATM if, VPI, VCI needs to be given.

The related ATM layer object in RNC MML: VPLtp (ZLC command group).

The related ATM plan managed object: VPTT object id.

The corresponding MML command group: ZQM, "VPI number".

Range 0... 4095

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 8 vpi (VPI) (Cont.)

24 DN70257257



IBFD Parameters

4 IBFD Parameters

4.1 alarmEnabled (Alarm enabled flag)

4.2 bfdEnabled (Bfd enabled flag)

Parameter name Alarm enabled flag

Abbreviated name alarmEnabled

3GPP name -

Managed Object IBFD

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines whether alarm reporting per BFD session is enabled or dis-abled.

The corresponding MML command group: ZYGS,"alarm".

Range Disable (0), Enable (1)

Step -

Units -


gui ==> internal

Disable ==> 0

Enable ==> 1

Default value Enable (1)


Related functions -

Modification On-Line



Related options -



References -

Table 9 alarmEnabled (Alarm enabled flag)

Parameter name Bfd enabled flag

Table 10 bfdEnabled (Bfd enabled flag)

DN70257257 25

IP Configuration Plan Interface Parameters IBFD Parameters


4.3 bfdId (BFD session id)

Abbreviated name bfdEnabled

3GPP name -

Managed Object IBFD

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines whether a BFD session is enabled or disabled. If it is dis-abled, the session remains in the "AdminDown" state until it is enabled again. It must be enabled for the Create operation if it exists in the download file.

The corresponding MML command group: ZYGS, "mode".


Step -

Units -


gui ==> internal

Disable ==> 0

Enable ==> 1



Related functions -




Related options -



References -

Table 10 bfdEnabled (Bfd enabled flag) (Cont.)

Parameter name BFD session id

Abbreviated name bfdId

3GPP name -

Managed Object IBFD

Parameter group -

Table 11 bfdId (BFD session id)

26 DN70257257



IBFD Parameters

4.4 dstIp (Destination IP address)

Classification -

Multiplicity 1

Description This parameter identifies the BFD session in the system. The identifier is part of the distinguished name and is formed in the following way: NE-x/IPNO-unitType-unit-Index/IBFD-bfdId. For example: RNC-02/IPNO-NPGEP-0/IBFD-1.

The corresponding MML command group: ZYGS,"session id".

Range 1... 3000

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 11 bfdId (BFD session id) (Cont.)

Parameter name Destination IP address

Abbreviated name dstIp

3GPP name -

Managed Object IBFD

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the destination IP address used for the BFD session. The address is specified in the conventional dot notation (#.#.#.#).

The corresponding MML command group: ZYGS,"remote IP address".

Range 7...15

Table 12 dstIp (Destination IP address)

DN70257257 27



4.5 ipbrId (Ip based route Id)

Step -

Units characters



Default value -

Default value notes default value is not possible

Related functions -




Related options -


Interfaces • RAC <-> RNC • RAC <-> RACApp

References -

Table 12 dstIp (Destination IP address) (Cont.)

Parameter name Ip based route Id

Abbreviated name ipbrId

3GPP name -

Managed Object IBFD

Parameter group -

Classification -

Multiplicity 1

Description This parameter identifies the IP based route to which the operator wants to asso-ciate the BFD session. The association is not mandatory but is needed to allow HSPA Transport Fallback basing on the BFD session status.

Range 0... 4095

Step 1

Units -



Default value 0

Default value notes 0 means undefined (no associated IPBR)

Table 13 ipbrId (Ip based route Id)

28 DN70257257



IBFD Parameters

4.6 profileId (Profile identifier)

Related functions -


Related parameters ipbrId of IPBR - The IP Based route must be created firstly.


Related options -



References -

Table 13 ipbrId (Ip based route Id) (Cont.)

Parameter name Profile identifier

Abbreviated name profileId

3GPP name -

Managed Object IBFD

Parameter group -

Classification -

Multiplicity 1

Description The profile identifier parameter is used to associate a BFD session to an existing BFD profile. The corresponding MML command group: ZYGS, "profile id".

Range 0... 7

Step 1

Units -



Default value 0


Related functions -




Related options -


Table 14 profileId (Profile identifier)

DN70257257 29



4.7 sessionType (Session Type)


References -

Table 14 profileId (Profile identifier) (Cont.)

Parameter name Session Type

Abbreviated name sessionType

3GPP name -

Managed Object IBFD

Parameter group -

Classification -

Multiplicity 1

Description The parameter defines the type of the BFD session. It can set values 0(BFD Multi-Hop Session), 1(ICMP Session) and 2(BFD Single-Hop Session).

The corresponding MML command:ZYGS

Range BFD MULTI-HOP (0), ICMP (1), BFD SINGLE-HOP (2)

Step -

Units -


gui ==> internal

BFD MULTI-HOP ==> 0

ICMP ==> 1

BFD SINGLE-HOP ==> 2

Default value BFD MULTI-HOP (0)


Related functions -




Related options -



References -

Table 15 sessionType (Session Type)

30 DN70257257



IBFD Parameters

4.8 srcIp (Source IP address)

Parameter name Source IP address

Abbreviated name srcIp

3GPP name -

Managed Object IBFD

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the source IP address used for the BFD session. The address is specified in the conventional dot notation (#.#.#.#).

The corresponding MML command group: ZYGS,"local IP address".

Range 7...15

Step -

Units characters



Default value -

Default value notes Default vlaue is not possible

Related functions -




Related options -



References -

Table 16 srcIp (Source IP address)

DN70257257 31

IP Configuration Plan Interface Parameters IBFP Parameters


5 IBFP Parameters

5.1 desiredMinTx (Min transmission interval)

5.2 detectMult (Detection multiplier)

Parameter name Min transmission interval

Abbreviated name desiredMinTx

3GPP name -

Managed Object IBFP

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the minimum interval between two transmitted control packets.

The corresponding MML command group:

For MHOP sessions, ZYGR,"minimum TX interval".

Range 500... 5000

Step 500

Units milliseconds



Default value 500


Related functions -




Related options -


Interfaces • RAC <-> RNC • RACApp <-> RAC

References -

Table 17 desiredMinTx (Min transmission interval)

Parameter name Detection multiplier

Table 18 detectMult (Detection multiplier)

32 DN70257257



IBFP Parameters

5.3 dscp (DSCP)

Abbreviated name detectMult

3GPP name -

Managed Object IBFP

Parameter group -

Classification -

Multiplicity 1

Description This parameter indicates the number of control packets that the RNC will lose

before the BFD session is declared down.

The corresponding MML command group: ZYGR, "detect multi".

Range 2... 10

Step 1

Units -



Default value 5


Related functions -




Related options -



References -

Table 18 detectMult (Detection multiplier) (Cont.)

Parameter name DSCP

Abbreviated name dscp

3GPP name -

Managed Object IBFP

Parameter group -

Classification -

Multiplicity 1

Table 19 dscp (DSCP)

DN70257257 33



5.4 profileId (IBFP identifier)

Description This parameter defines the DSCP value.

The corresponding MML command: ZYGR.

Range 0... 63

Step 1

Units -



Default value 34


Related functions -




Related options -



References -

Table 19 dscp (DSCP) (Cont.)

Parameter name IBFP identifier


3GPP name -

Managed Object IBFP

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the Multi-hop BFD profile in the system.

The default profile with the profile id "0" cannot be udpated or deleted.

It exists only in the upload file and is returned for planning purposes.

The identifier is part of

the distinguished name and it is formed in the following way: NE-x/IBFP-profileId. For example: RNC-02/IBFP-1.

The corresponding MML command group: ZYGR, "profile id".

Table 20 profileId (IBFP identifier)

34 DN70257257



IBFP Parameters

5.5 profileName (Multi-Hop BFD Profile Name)

Range 0... 7

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 20 profileId (IBFP identifier) (Cont.)

Parameter name Multi-Hop BFD Profile Name

Abbreviated name profileName

3GPP name -

Managed Object IBFP

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the name of the BFD profile.

The different profiles can use the same name.

MML command ZYGR is used in the Multi-Hop profile.

Range 1...10

Step -

Units characters



Default value UNDEFINED

Table 21 profileName (Multi-Hop BFD Profile Name)

DN70257257 35



5.6 requiredMinRx (Required minimum reception interval)


Related functions -




Related options -



References -

Table 21 profileName (Multi-Hop BFD Profile Name) (Cont.)

Parameter name Required minimum reception interval

Abbreviated name requiredMinRx

3GPP name -

Managed Object IBFP

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the minimum required interval between two received control packets.

The corresponding MML command group:

For MHOP sessions, ZYGR,"minimum RX interval".

Range 500... 5000

Step 500

Units milliseconds



Default value 500


Related functions -




Table 22 requiredMinRx (Required minimum reception interval)

36 DN70257257



IBFP Parameters

Related options -



References -

Table 22 requiredMinRx (Required minimum reception interval) (Cont.)

DN70257257 37

IP Configuration Plan Interface Parameters IDNS Parameters


6 IDNS Parameters

6.1 cache (Resolver Cache)

Parameter name Resolver Cache

Abbreviated name cache

3GPP name -

Managed Object IDNS

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines whether the cache is in use or not. If the parameter is given for the first time, the default value is "YES", otherwise the default value is the current value. The possible values to the parameter are:

YES = The resolver cache is in use.

NO = The resolver cache is not in use.

The corresponding MML command group: ZQRK, "resolver cache".

Range No (0), Yes (1)

Step -

Units -


gui ==> internal

No ==> 0

Yes ==> 1

Default value Yes (1)


Related functions -




Related options -



References -

Table 23 cache (Resolver Cache)

38 DN70257257



IDNS Parameters

6.2 iDNSId (DNS Identifier)

6.3 localDomain (Local domain name)

Parameter name DNS Identifier

Abbreviated name iDNSId

3GPP name -

Managed Object IDNS

Parameter group -

Classification -

Multiplicity 1

Description This parameter identifies the DNS entity related to the IPNO in the system. There is only one IDNS within the IPNO. The identifier is part of the distinguished name and it is formed in the following way: NE-x/IPNO-unitType-unitIndex/IDNS-1. For example: RNC-1/IPNO-OMU-0/IDNS-1.

The corresponding MML command group: ZQRK.

Range 1... 1

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 24 iDNSId (DNS Identifier)

Parameter name Local domain name

Abbreviated name localDomain

3GPP name -

Table 25 localDomain (Local domain name)

DN70257257 39



6.4 roundRobin (Round robin)

Managed Object IDNS

Parameter group -

Classification -

Multiplicity 1

Description The local domain name as a character string. The maximum length of the name is 100 characters. If you enter a full stop (".") as the value, no domain name is used. The default value is the current value.

The corresponding MML command group: ZQRK, "local domain name".

Range 1...100

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 25 localDomain (Local domain name) (Cont.)

Parameter name Round robin

Abbreviated name roundRobin

3GPP name -

Managed Object IDNS

Parameter group -

Classification -

Multiplicity 1

Table 26 roundRobin (Round robin)

40 DN70257257



IDNS Parameters

6.5 serverIPAddr (Server IP address list)

Description This parameter defines whether the round robin is in use or not. If the parameter is given for the first time, the default value is "YES", otherwise the default value is the current value. The possible values to the parameter are:

YES = The round robin is in use.

NO = The round robin is not in use.

The corresponding MML command group: ZQRK, "round robin".


Step -

Units -


gui ==> internal

No ==> 0

Yes ==> 1



Related functions -




Related options -



References -

Table 26 roundRobin (Round robin) (Cont.)

Parameter name Server IP address list

Abbreviated name serverIPAddr

3GPP name -

Managed Object IDNS

Parameter group -

Classification -

Multiplicity 3

Description Server IP address list. The corresponding MML command group: ZQRK, "pri-mary/secondary/third DNS server".

Table 27 serverIPAddr (Server IP address list)

DN70257257 41



6.6 addrValue (Address value)


-

Default value -


Related functions -

Child parameters • addrValue • addrVer




Related options -



References -

Table 27 serverIPAddr (Server IP address list) (Cont.)

Parameter name Address value

Abbreviated name addrValue

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description The IP address of the server. The address is specified in the conventional dot notation (#.#.#.#).

The corresponding MML command group: ZQRK, "primary/secondary/third DNS server".

Range 7...39

Step -

Units characters



Default value -


Table 28 addrValue (Address value)

42 DN70257257



IDNS Parameters

6.7 addrVer (IP address version for server IP address)

Related functions -




Related options -



References -

Table 28 addrValue (Address value) (Cont.)

Parameter name IP address version for server IP address

Abbreviated name addrVer

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description The IP address version for the server IP address. The corresponding MML command: ZQRK, "primary/secondary/third DNS server".

Range IPV4 (0)

Step -

Units -


gui ==> internal

IPV4 ==> 0

Default value IPV4 (0)


Related functions -




Related options -


Table 29 addrVer (IP address version for server IP address)

DN70257257 43



6.8 sortList (Network sortlist)


References -

Table 29 addrVer (IP address version for server IP address) (Cont.)

Parameter name Network sortlist

Abbreviated name sortList

3GPP name -

Managed Object IDNS

Parameter group -

Classification -

Multiplicity 10

Description The IP address of the sortlist. The address is specified in the conventional dot notation (#.#.#.#).

If you enter "0.0.0.0" as the value, there is no sortlist. The default value is the current value.

The corresponding MML command group: ZQRK, "sortlist".


-

Default value -


Related functions -

Child parameters • addrValue • netmask




Related options -



References -

Table 30 sortList (Network sortlist)

44 DN70257257



IDNS Parameters

6.9 addrValue (Address value)

6.10 netmask (Netmask)

Parameter name Address value

Abbreviated name addrValue

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description The IP address of the sortlist. The address is specified in the conventional dot notation (#.#.#.#).

If you enter '0.0.0.0' as the value, there is no sortlist. The default value is the current value.

The corresponding MML command group: ZQRK, "sortlist".

Range 7...39

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 31 addrValue (Address value)

Parameter name Netmask

Abbreviated name netmask

3GPP name -

Table 32 netmask (Netmask)

DN70257257 45



Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description Netmask for the sortlist address.

The corresponding MML command: ZQRK, "sortlist".

Range 7...39

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 32 netmask (Netmask) (Cont.)

46 DN70257257



IDSP Parameters

7 IDSP Parameters

7.1 dscpProfileName (DSCP to PHB mapping ProfileName)

Parameter name DSCP to PHB mapping ProfileName

Abbreviated name dscpProfileName

3GPP name -

Managed Object IDSP

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the DSCP to PHB mapping profile name.

The profile name 'DEFAULT' is the default profile and it cannot be updated or deleted. It exists only in the upload file for planning purposes.

The profile name is unique in the RNC.

The corresponding MML command group: ZQ8B, "profile name".

Range 1...20

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 33 dscpProfileName (DSCP to PHB mapping ProfileName)

DN70257257 47

IP Configuration Plan Interface Parameters IDSP Parameters


7.2 idspId (DSCP to PHB mapping profile Identifier)

7.3 profileList (Profile list)

Parameter name DSCP to PHB mapping profile Identifier

Abbreviated name idspId

3GPP name -

Managed Object IDSP

Parameter group -

Classification -

Multiplicity 1

Description This parameter identifies the DSCP to PHB mapping profile in the system.

The profile id 0 is the default profile and it cannot be updated or deleted. It exists only in the upload file for planning purposes.

The profile id is unique in the RNC.

The identifier is part of the distinguished name and it is formed in the following way:

NE-x/IDSP-dspId. For example: RNC-1/IDSP-1.

The corresponding MML command group: ZQ8B, "profile id".

Range 0... 10

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 34 idspId (DSCP to PHB mapping profile Identifier)

Parameter name Profile list

Table 35 profileList (Profile list)

48 DN70257257



IDSP Parameters

7.4 dscpNumber (Dscp Value)

Abbreviated name profileList

3GPP name -

Managed Object IDSP

Parameter group -

Classification -

Multiplicity 64

Description This parameter defines the DSCP to the PHB mapping profile.

There is one default profile for mapping the DSCP to PHB.

When you create another profile, you can input only some mapping items other than 64; for others, the mapping relationship in the default profile is used.


-

Default value -


Related functions -

Child parameters • dscpNumber • phb




Related options -



References -

Table 35 profileList (Profile list) (Cont.)

Parameter name Dscp Value

Abbreviated name dscpNumber

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Table 36 dscpNumber (Dscp Value)

DN70257257 49

IP Configuration Plan Interface Parameters IDSP Parameters


7.5 phb (PHB value)

Description This parameter defines the DSCP value which is used for mapping the PHB value.

The corresponding MML command group: ZQ8B.

Range 0... 63

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 36 dscpNumber (Dscp Value) (Cont.)

Parameter name PHB value

Abbreviated name phb

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the PHB value which used for the DSCP value mapping.

The corresponding MML command group: ZQ8B.

Range BE (0), EF (1), AF1 (21), AF2 (22), AF3 (23), AF4 (24)

Step -

Units -

Table 37 phb (PHB value)

50 DN70257257



IDSP Parameters


gui ==> internal

BE ==> 0

EF ==> 1

AF1 ==> 21

AF2 ==> 22

AF3 ==> 23

AF4 ==> 24

Default value -


Related functions -




Related options -



References -

Table 37 phb (PHB value) (Cont.)

DN70257257 51

IP Configuration Plan Interface Parameters IEIF Parameters


8 IEIF Parameters

8.1 IPV4Addr (IPv4 address list)

8.2 addrTypeIPV4 (Address type IPv4)

Parameter name IPv4 address list

Abbreviated name IPV4Addr

3GPP name -

Managed Object IEIF

Parameter group -

Classification -

Multiplicity 10

Description IPv4 address list. The corresponding MML command group: ZQRN.

One interface can support 10 physical IP addresses and/or 10 logical IP addresses.


-

Default value -


Related functions -

Child parameters • addrTypeIPV4 • addrValueIPV4 • destAddrIPV4 • netmask




Related options -



References -

Table 38 IPV4Addr (IPv4 address list)

Parameter name Address type IPv4

Abbreviated name addrTypeIPV4

Table 39 addrTypeIPV4 (Address type IPv4)

52 DN70257257



IEIF Parameters

8.3 addrValueIPV4 (IP address IPv4)

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description The logical or physical IP address for the network interface.

Logical IP address: This address belongs to the specified interface of the specified functional unit. The logical IP address follows the active unit. The logical IP address can be given to 2N and N+1 units. In N+1 units, you have to identify the unit type and the unit index. In 2N units, you only have to identify the unit type of the 2N unit; the unit index is not needed for DMX unit.

Physical IP address: This address is assigned to the specified computer unit per-manently. Note that with the physical IP address you have to identify both the unit type and the unit index. The physical IP address is not allowed in the 2N IP-NIU type units and EIPU units.

The corresponding MML command group: ZQRN

Range Physical (0), Logical (1)

Step -

Units -


gui ==> internal

Physical ==> 0

Logical ==> 1

Default value -

Default value notes Default value is based on the unit type and index.

Related functions -




Related options -



References -

Table 39 addrTypeIPV4 (Address type IPv4) (Cont.)

Parameter name IP address IPv4

Table 40 addrValueIPV4 (IP address IPv4)

DN70257257 53



8.4 destAddrIPV4 (Destination address IPv4)

Abbreviated name addrValueIPV4

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description IPv4 Address, 10 physical addresses and 10 logical addresses can be set for one interface.

The corresponding MML command group: ZQRN, "IP address".

Range 7...15

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 40 addrValueIPV4 (IP address IPv4) (Cont.)

Parameter name Destination address IPv4

Abbreviated name destAddrIPV4

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Table 41 destAddrIPV4 (Destination address IPv4)

54 DN70257257



IEIF Parameters


Description The IP address of the point-to-point link. This parameter can be given only if the interface type is 'AA', 'IFAI', or 'IFAE'. The corresponding MML command group: ZQRN, "destination IP address".The address is specified in the conventional dot notation (#.#.#.#). The range for each part of the address is from 0 to 255.

The corresponding MML command group: ZQRN, "destination IP address".

Range 7...15

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 41 destAddrIPV4 (Destination address IPv4) (Cont.)



3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description Netmask for the address.

The corresponding MML command group: ZQRN, "netmask".

Range 7...15

Step -

Units characters


DN70257257 55



8.6 administrativeState (Administrative state)



Default value -


Related functions -




Related options -



References -

Table 42 netmask (Netmask) (Cont.)

Parameter name Administrative state

Abbreviated name administrativeState

3GPP name -

Managed Object IEIF

Parameter group -

Classification -

Multiplicity 1

Description This parameter indicates the initial administrative state of the interface immediately after the configuration. If the interface is configured for the first time, the default value is "UP". If the state is omitted and the network interface has been configured before, the state does not change.

The corresponding MML command: ZQRN, "state".

Range UP (1), DOWN (3)

Step -

Units -


gui ==> internal

UP ==> 1

DOWN ==> 3

Default value UP (1)


Table 43 administrativeState (Administrative state)

56 DN70257257



IEIF Parameters

8.7 ethIfNetId (Ethernet Interface Identifier)

Related functions -




Related options -



References -

Table 43 administrativeState (Administrative state) (Cont.)

Parameter name Ethernet Interface Identifier

Abbreviated name ethIfNetId

3GPP name -

Managed Object IEIF

Parameter group -

Classification -

Multiplicity 1

Description This parameter identifies the network interface within the IP node entity in the system. The identifier is part of the distinguished name and it is formed in following way: NE-x/IPNO-unitType-unitIndex/IEIF-ifName. For example: RNC-1/IPNO-OMU-0/IEIF-EL0.

The name must start with 'AA' (external or internal IPoA interface), 'IFAE' (external IPOA interface), 'IFAI' (internal IPOA interface), 'EL'(ethernet interface), 'IFETH' and 'IFFGE' (ethernet interface), 'IFFE'and 'IFGE' (ethernet interface), 'LO' (Loop-back interface), or 'VL' (VLAN interface).

The corresponding MML command group: ZQRN, "interface name".

Range 3...8

Step -

Units characters



Default value -


Related functions -

Table 44 ethIfNetId (Ethernet Interface Identifier)

DN70257257 57



8.8 ifType (Interface type)




Related options -



References -

Table 44 ethIfNetId (Ethernet Interface Identifier) (Cont.)

Parameter name Interface type

Abbreviated name ifType

3GPP name -

Managed Object IEIF

Parameter group -

Classification -

Multiplicity 1

Description A numbered or unnumbered point to point interface type for the network interface. This parameter is only valid to ATM ('AA', 'IFAE' and 'IFAI') point to point inter-faces.If you want to change the point to point interface type, you have to remove the interface by using the command QRG and configure it as another point to point interface type.

The numbered interface has a unique IP address. This is the default value.

The unnumbered interface does not have a unique IP address, but it shares its IP address with the Ethernet interface's IP address.

The corresponding MML command group: ZQRN, "point to point interface type".

Range Unnumbered (0), Numbered (1)

Step -

Units -


gui ==> internal

Unnumbered ==> 0

Numbered ==> 1

Default value Numbered (1)


Related functions -

Table 45 ifType (Interface type)

58 DN70257257



IEIF Parameters

8.9 mtu (Maximum Transfer Unit)




Related options -



References -

Table 45 ifType (Interface type) (Cont.)

Parameter name Maximum Transfer Unit

Abbreviated name mtu

3GPP name -

Managed Object IEIF

Parameter group -

Classification -

Multiplicity 1

Description The maximum transmittable size of a single, complete IP data unit. You can give MTU only for some interfaces.

For LO of DMX units, the value is fixed to 33204.

For LO of chorus units (except NPGE and NPS1), the value is fixed to 16384.

For NPGE LO is 500-4500, and default value is 1500. For NPS1 LO is 500-9180, and default value is 9180.

The range of AA and IFAE is 500-9180, and default value is 9180.

The range of VL, IFGE and IFAI is 500-4500, and default value is 1500.

For EL, IFETH and IFFE, the value is fixed to 1500.

The corresponding MML command group: ZQRN, "MTU".

Range 1... 65535

Step 1

Units -



Default value 1500

Default value notes The default value is different based on the unit type and unit interface.

Related functions -

Table 46 mtu (Maximum Transfer Unit)

DN70257257 59






Related options -



References -

Table 46 mtu (Maximum Transfer Unit) (Cont.)

60 DN70257257



IGIF Parameters

9 IGIF Parameters

9.1 RncEthernetBw (EthernetBw)

9.2 ethInterfaceRate (Ethernet interface rate)

Parameter name EthernetBw

Abbreviated name RncEthernetBw

3GPP name -

Managed Object IGIF

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the ethernet interface bandwidth.

The corresponding MML command: ZQA,"Ethernet interface

bandwidth".

Range 100... 1000

Step 100

Units Mbps



Default value 1000


Related functions -




Related options -



References -

Table 47 RncEthernetBw (EthernetBw)

Parameter name Ethernet interface rate

Abbreviated name ethInterfaceRate

Table 48 ethInterfaceRate (Ethernet interface rate)

DN70257257 61

IP Configuration Plan Interface Parameters IGIF Parameters


9.3 igifId (Ethernet Interface Identifier)

3GPP name -

Managed Object IGIF

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the ethernet interface rate. A special rate value 0 indicates that autonegotiation is on.

The corresponding MML command: ZQA,"Ethernet interface rate".

Range Autonegotation (0)

Step -

Units -


gui ==> internal

Autonegotation ==> 0

Default value Autonegotation (0)


Related functions -




Related options -



References -

Table 48 ethInterfaceRate (Ethernet interface rate) (Cont.)

Parameter name Ethernet Interface Identifier

Abbreviated name igifId

3GPP name -

Managed Object IGIF

Parameter group -

Classification -

Multiplicity 1

Table 49 igifId (Ethernet Interface Identifier)

62 DN70257257



IGIF Parameters

Description This parameter identifies the Ethernet interface which configures the rate and bandwidth in the system. Only IFGE interface is supported on NPGE(P) unit.

The identifier is part of the distinguished name and it is formed in the following way: NE-x/IPNO-unitType-unitIndex/IGIF-ifName. For example: RNC-1/IPNO-NPGEP-0/IGIF-IFGE0.

The corresponding MML command: ZQA,"interface name".

Range 3...8

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 49 igifId (Ethernet Interface Identifier) (Cont.)

DN70257257 63

IP Configuration Plan Interface Parameters IICP Parameters


10 IICP Parameters

10.1 echoReplyTmout (Timeout for echo reply re-ceiving)

10.2 echoReqPeriod (Period for echo request packet sending)

Parameter name Timeout for echo reply re-ceiving

Abbreviated name echoReplyTmout

3GPP name -

Managed Object IICP

Parameter group -

Classification -

Multiplicity 1

Description Echo Reply timeout is the maximum time waited for an Echo Reply message after an Echo Request. If an Echo Reply is not received within this time, it is considered lost. Reply Timeout value must be strictly less than request period.

Range 100... 600000

Step 50

Units -



Default value 500


Related functions -




Related options -



References -

Table 50 echoReplyTmout (Timeout for echo reply re-ceiving)

Parameter name Period for echo request packet sending

Abbreviated name echoReqPeriod

Table 51 echoReqPeriod (Period for echo request packet sending)

64 DN70257257



IICP Parameters

10.3 maxLostPkt (maxLostPkt)

3GPP name -

Managed Object IICP

Parameter group -

Classification -

Multiplicity 1

Description Echo Request period is the desired time between two consecutive Echo Request packets sent over network.

Range 150... 600000

Step 50

Units -



Default value 1000


Related functions -




Related options -



References -

Table 51 echoReqPeriod (Period for echo request packet sending) (Cont.)

Parameter name maxLostPkt

Abbreviated name maxLostPkt

3GPP name -

Managed Object IICP

Parameter group -

Classification -

Multiplicity 1

Table 52 maxLostPkt (maxLostPkt)

DN70257257 65



10.4 payloadLength (payloadLength)

Description This parameter defines the number of icmp echo reply packets that are lost contin-ually, in order for the session to be declared in down state.

Maximum lost packets indicates the number of consecutive lost Echo Replies to be waited for before declaring a session as "Down".

Range 1... 255

Step 1

Units -



Default value 5


Related functions -




Related options -



References -

Table 52 maxLostPkt (maxLostPkt) (Cont.)

Parameter name payloadLength

Abbreviated name payloadLength

3GPP name -

Managed Object IICP

Parameter group -

Classification -

Multiplicity 1

Description ICMP Payload length represents the payload size of sent Echo Requests.

Range 0... 128

Step 1

Units -



Table 53 payloadLength (payloadLength)

66 DN70257257



IICP Parameters

10.5 profileId (IICP identifier)

Default value 64


Related functions -




Related options -



References -

Table 53 payloadLength (payloadLength) (Cont.)

Parameter name IICP identifier


3GPP name -

Managed Object IICP

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the IICP profile in the system.

The default profile with the profile id "0" cannot be udpated or deleted.

It exists only in the upload file and is returned for planning purposes.

The identifier is part of the distinguished name and it is formed in the following way: NE-x/IICP-profileId. For example: RNC-02/IICP-1.

The corresponding MML command group: ZYGQ, "profile id".

Range 0... 7

Step 1

Units -



Default value -


Related functions -

Table 54 profileId (IICP identifier)

DN70257257 67






Related options -



References -

Table 54 profileId (IICP identifier) (Cont.)

68 DN70257257



IOAM Parameters

11 IOAM Parameters

11.1 InstanceID (Ethernet OAM Instance ID)

Parameter name Ethernet OAM Instance ID

Abbreviated name InstanceID

3GPP name -

Managed Object IOAM

Parameter group -

Classification -

Multiplicity 1

Description This parameter identifies the Ethernet interface which is for Ethernet OAM. Only IFGE and IFFE interfaces are supported on NPGE(P) unit.

The identifier is part of the distinguished name and it is formed in the following way: NE-x/IPNO-unitType-unitIndex/IOAM-ifName. For example: RNC-1/IPNO-NPGEP-0/IOAM-IFGE0.

The corresponding MML command: ZQAN,"interface name".

Range 3...8

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 55 InstanceID (Ethernet OAM Instance ID)

DN70257257 69

IP Configuration Plan Interface Parameters IOAM Parameters


11.2 activeMode (Link OAM working Mode)

11.3 adminState (Link OAM Administration State )

Parameter name Link OAM working Mode

Abbreviated name activeMode

3GPP name -

Managed Object IOAM

Parameter group -

Classification -

Multiplicity 1

Description The working mode for Ethernet OAM is defined with the link OAM mode parameter.

The corresponding MML command: ZQAN

Range ACTIVE (1), PASSIVE (2)

Step -

Units -


gui ==> internal

ACTIVE ==> 1

PASSIVE ==> 2

Default value PASSIVE (2)


Related functions -




Related options -



References -

Table 56 activeMode (Link OAM working Mode)

Parameter name Link OAM Administration State

Abbreviated name adminState

3GPP name -

Managed Object IOAM

Table 57 adminState (Link OAM Administration State )

70 DN70257257



IOAM Parameters

11.4 almClrTimer (Link OAM Critical Event Alarm Clearance Timer)

Parameter group -

Classification -

Multiplicity 1

Description Ethernet OAM functionality is enabled/disabled with the link OAM administration state parameter. When the feature is disabled, the other Ethernet OAM related parameters do not have any effect.


Range ENABLE (1), DISABLE (2)

Step -

Units -


gui ==> internal

ENABLE ==> 1

DISABLE ==> 2

Default value DISABLE (2)


Related functions -




Related options -



References -

Table 57 adminState (Link OAM Administration State ) (Cont.)

Parameter name Link OAM Critical Event Alarm Clearance Timer

Abbreviated name almClrTimer

3GPP name -

Managed Object IOAM

Parameter group -

Classification -

Multiplicity 1

Table 58 almClrTimer (Link OAM Critical Event Alarm Clearance Timer)

DN70257257 71



11.5 efEvtThd (Link OAM Error Frame Event Threshold)

Description This parameter defines the time to clean the link OAM critical event alarm when there is no Critical Event Flag received.

If the templateID is given, this parameter must be empty.

If this parameter is filled, the templateID must be empty.


Range 1... 10

Step 1

Units -



Default value -

Default value notes If the templateID is given, this parameter must be empty.If this parameter is filled, the templateID must be empty.

Related functions -




Related options -



References -

Table 58 almClrTimer (Link OAM Critical Event Alarm Clearance Timer) (Cont.)

Parameter name Link OAM Error Frame Event Threshold

Abbreviated name efEvtThd

3GPP name -

Managed Object IOAM

Parameter group -

Classification -

Multiplicity 1

Table 59 efEvtThd (Link OAM Error Frame Event Threshold)

72 DN70257257



IOAM Parameters

11.6 efEvtWnd (Link OAM Error Frame Event Window)

Description This parameter defines the threshold for the error frame events. If the received error frames number is beyond the threshold during the window defined by efE-vtWnd, the peer will be alerted with event notification.




Range 0... 65535

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 59 efEvtThd (Link OAM Error Frame Event Threshold) (Cont.)

Parameter name Link OAM Error Frame Event Window

Abbreviated name efEvtWnd

3GPP name -

Managed Object IOAM

Parameter group -

Classification -

Multiplicity 1

Table 60 efEvtWnd (Link OAM Error Frame Event Window)

DN70257257 73



11.7 efSecThd (Link OAM Error Frame Seconds Threshold)

Description This parameter defines the time window for the error frame events statistics.




Range 1... 60

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 60 efEvtWnd (Link OAM Error Frame Event Window) (Cont.)

Parameter name Link OAM Error Frame Seconds Threshold

Abbreviated name efSecThd

3GPP name -

Managed Object IOAM

Parameter group -

Classification -

Multiplicity 1

Table 61 efSecThd (Link OAM Error Frame Seconds Threshold)

74 DN70257257



IOAM Parameters

11.8 efSecWnd (Link OAM Error Frame Seconds Window)

Description This parameter defines the threshold for the error frame seconds.

If the error frame is received during 1 second, the second is called the error frame second.

The parameter cannot be greater than efSecWnd.

If the error frame second number is beyond the threshold during the window defined by efSecWnd, the peer will be alerted with event notification.




Range 0... 900

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 61 efSecThd (Link OAM Error Frame Seconds Threshold) (Cont.)

Parameter name Link OAM Error Frame Seconds Window

Abbreviated name efSecWnd

3GPP name -

Managed Object IOAM

Parameter group -

Classification -

Multiplicity 1

Table 62 efSecWnd (Link OAM Error Frame Seconds Window)

DN70257257 75



11.9 lostTimer (Ethernet OAM Link Timeout)

Description This parameter defines the time window for the error frame seconds statistics.




Range 10... 900

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 62 efSecWnd (Link OAM Error Frame Seconds Window) (Cont.)

Parameter name Ethernet OAM Link Timeout

Abbreviated name lostTimer

3GPP name -

Managed Object IOAM

Parameter group -

Classification -

Multiplicity 1

Table 63 lostTimer (Ethernet OAM Link Timeout)

76 DN70257257



IOAM Parameters

11.10 lpDuration (Link OAM Loopback Duration Time)

Description This parameter is the maximum time that the OAM link peer responses. If the peer response is not received, it shows that the peer is inoperative.

If the parameter is modified, OAM discovery process will be reset.




Range 2... 30

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 63 lostTimer (Ethernet OAM Link Timeout) (Cont.)

Parameter name Link OAM Loopback Duration Time

Abbreviated name lpDuration

3GPP name -

Managed Object IOAM

Parameter group -

Classification -

Multiplicity 1

Table 64 lpDuration (Link OAM Loopback Duration Time)

DN70257257 77



11.11 lpLostTimer (Link OAM Loopback Timeout)

Description This parameter defines the time interval beyond which the remote loopback is dis-abled.

If loopback is enabled by local interface, it will be disabled when this time timeout.




Range 10... 300

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 64 lpDuration (Link OAM Loopback Duration Time) (Cont.)

Parameter name Link OAM Loopback Timeout

Abbreviated name lpLostTimer

3GPP name -

Managed Object IOAM

Parameter group -

Classification -

Multiplicity 1

Table 65 lpLostTimer (Link OAM Loopback Timeout)

78 DN70257257



IOAM Parameters

11.12 lpPktRate (Link OAM Loopback Packet Rate)

Description This parameter defines the time interval beyond which the local loopback is dis-abled.

If the loopback is enabled by remote interface, it will be disabled when this time timeout.




Range 10... 300

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 65 lpLostTimer (Link OAM Loopback Timeout) (Cont.)

Parameter name Link OAM Loopback Packet Rate

Abbreviated name lpPktRate

3GPP name -

Managed Object IOAM

Parameter group -

Classification -

Multiplicity 1

Table 66 lpPktRate (Link OAM Loopback Packet Rate)

DN70257257 79



11.13 lpPktSize (Link OAM Loopback Packet Size )

Description This parameter defines the packet rate of the test frames during the loopback enabled.




Range 20... 1000

Step 20

Units -



Default value -


Related functions -




Related options -



References -

Table 66 lpPktRate (Link OAM Loopback Packet Rate) (Cont.)

Parameter name Link OAM Loopback Packet Size

Abbreviated name lpPktSize

3GPP name -

Managed Object IOAM

Parameter group -

Classification -

Multiplicity 1

Table 67 lpPktSize (Link OAM Loopback Packet Size )

80 DN70257257



IOAM Parameters

11.14 pduTimer (Link OAM PDU Timer)

Description This parameter defines the packet size of the test packets during Loopback enabled.

For IFGE interface, the max packet size is 1518 on NPGE(P) unit.

For IFFE interface, the max packet size is 1514 on NPGE(P) unit.




Range 64... 1518

Step 1

Units -



Default value -

Default value notes For IFGE interface, the max packet size is 1518 on NPGE(P) unit.For IFFE inter-face, the max packet size is 1514 on NPGE(P) unit.If the templateID is given, this parameter must be empty.If this parameter is filled, the templateID must be empty.

Related functions -




Related options -



References -

Table 67 lpPktSize (Link OAM Loopback Packet Size ) (Cont.)

Parameter name Link OAM PDU Timer

Abbreviated name pduTimer

3GPP name -

Managed Object IOAM

Parameter group -

Classification -

Multiplicity 1

Table 68 pduTimer (Link OAM PDU Timer)

DN70257257 81



11.15 templateID (Template ID)

Description This parameter defines the time period of sending OAM PDU.




Range 100... 1000

Step 100

Units -



Default value -


Related functions -




Related options -



References -

Table 68 pduTimer (Link OAM PDU Timer) (Cont.)

Parameter name Template ID

Abbreviated name templateID

3GPP name -

Managed Object IOAM

Parameter group -

Classification -

Multiplicity 1

Table 69 templateID (Template ID)

82 DN70257257



IOAM Parameters

Description This parameter defines the template ID which used by the OAM link. The OAM template include the following parameters: (pduTimer,lostTimer,lpLostTimer,alm-ClrTimer,efEvtThd,efEvtWnd,efSecThd,efSecWnd,lpDuration,lpPktRate,lpPkt-Size).

If the templateID is given, the above parameters in brackets must be empty.

If any of the above parameters in brackets is filled, the templateID must be empty.


Range 1... 5

Step 1

Units -



Default value -

Default value notes The OAM template include the following parameters: (pduTimer,lostTimer,lpLost-Timer,almClrTimer,efEvtThd,efEvtWnd,efSecThd,efSecWnd,lpDuration,lpPk-tRate,lpPktSize).If the templateID is given, the above parameters in brackets must be empty.If any of the above parameters in brackets is filled, the templateID must be empty.

Related functions -




Related options -



References -

Table 69 templateID (Template ID) (Cont.)

DN70257257 83

IP Configuration Plan Interface Parameters IOAMT Parameters


12 IOAMT Parameters

12.1 almClrTimer (Link OAM Critical Event Alarm Clearance Timer)

12.2 efEvtThd (Link OAM Error Frame Event Threshold)

Parameter name Link OAM Critical Event Alarm Clearance Timer

Abbreviated name almClrTimer

3GPP name -

Managed Object IOAMT

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the time to clean the link OAM critical event alarm when there is no Critical Event Flag received.

The corresponding MML command: ZQAT

Range 1... 10

Step 1

Units -



Default value 5


Related functions -




Related options -



References -

Table 70 almClrTimer (Link OAM Critical Event Alarm Clearance Timer)

Parameter name Link OAM Error Frame Event Threshold

Table 71 efEvtThd (Link OAM Error Frame Event Threshold)

84 DN70257257



IOAMT Parameters

12.3 efEvtWnd (Link OAM Error Frame Event Window)

Abbreviated name efEvtThd

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the threshold for the error frame events. If the received error frames number is beyond the threshold during the window defined by efE-vtWnd, the peer will be alerted with event notification.


Range 0... 65535

Step 1

Units -



Default value 1


Related functions -




Related options -



References -

Table 71 efEvtThd (Link OAM Error Frame Event Threshold) (Cont.)

Parameter name Link OAM Error Frame Event Window

Abbreviated name efEvtWnd

3GPP name -


Parameter group -

Classification -

Table 72 efEvtWnd (Link OAM Error Frame Event Window)

DN70257257 85



12.4 efSecThd (Link OAM Error Frame Seconds Threshold )

Multiplicity 1

Description This parameter defines the time window for the error frame events statistics.


Range 1... 60

Step 1

Units -



Default value 1


Related functions -




Related options -



References -

Table 72 efEvtWnd (Link OAM Error Frame Event Window) (Cont.)

Parameter name Link OAM Error Frame Seconds Threshold

Abbreviated name efSecThd

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Table 73 efSecThd (Link OAM Error Frame Seconds Threshold )

86 DN70257257



IOAMT Parameters

12.5 efSecWnd (Link OAM Error Frame Seconds Window)

Description This parameter defines the threshold for the error frame seconds.

If the error frame is received during 1 second, the second is called the error frame second.

The parameter cannot be greater than efSecWnd.

If the error frame second number is beyond the threshold during the window defined by efSecWnd, the peer will be alerted with event notification.


Range 0... 900

Step 1

Units -



Default value 1


Related functions -




Related options -



References -

Table 73 efSecThd (Link OAM Error Frame Seconds Threshold ) (Cont.)

Parameter name Link OAM Error Frame Seconds Window

Abbreviated name efSecWnd

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the time window for the error frame seconds statistics.


Table 74 efSecWnd (Link OAM Error Frame Seconds Window)

DN70257257 87



12.6 lostTimer (Ethernet OAM Link Timeout)

Range 10... 900

Step 1

Units -



Default value 60


Related functions -




Related options -



References -

Table 74 efSecWnd (Link OAM Error Frame Seconds Window) (Cont.)

Parameter name Ethernet OAM Link Timeout

Abbreviated name lostTimer

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Description This parameter is the maximum time that the OAM link peer responses. If the peer response is not received, it shows that the peer is inoperative.


Range 2... 30

Step 1

Units -



Default value 5

Table 75 lostTimer (Ethernet OAM Link Timeout)

88 DN70257257



IOAMT Parameters

12.7 lpDuration (Link OAM Loopback Duration Time)


Related functions -




Related options -



References -

Table 75 lostTimer (Ethernet OAM Link Timeout) (Cont.)

Parameter name Link OAM Loopback Duration Time

Abbreviated name lpDuration

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the time interval beyond which the remote loopback is dis-abled.

If loopback is enabled by local interface, it will be disabled when this time timeout.


Range 10... 300

Step 10

Units -



Default value 10


Related functions -




Table 76 lpDuration (Link OAM Loopback Duration Time)

DN70257257 89



12.8 lpLostTimer (Link OAM Loopback Timeout)

Related options -



References -

Table 76 lpDuration (Link OAM Loopback Duration Time) (Cont.)

Parameter name Link OAM Loopback Timeout

Abbreviated name lpLostTimer

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the time interval beyond which the local loopback is dis-abled.

If the loopback is enabled by remote interface, it will be disabled when this time timeout.


Range 10... 300

Step 1

Units -



Default value 10


Related functions -




Related options -



Table 77 lpLostTimer (Link OAM Loopback Timeout)

90 DN70257257



IOAMT Parameters

12.9 lpPktRate (Link OAM Loopback Packet Rate)

12.10 lpPktSize (Link OAM Loopback Packet Size)

References -

Table 77 lpLostTimer (Link OAM Loopback Timeout) (Cont.)

Parameter name Link OAM Loopback Packet Rate

Abbreviated name lpPktRate

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the packet rate of the test frames during the loopback enabled.


Range 20... 1000

Step 20

Units -



Default value 20


Related functions -




Related options -



References -

Table 78 lpPktRate (Link OAM Loopback Packet Rate)

Parameter name Link OAM Loopback Packet Size

Table 79 lpPktSize (Link OAM Loopback Packet Size)

DN70257257 91



12.11 pduTimer (Link OAM PDU Timer)

Abbreviated name lpPktSize

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the packet size of the test packets during Loopback enabled.

For IFGE interface, the max packet size is 1518 on NPGE(P) unit.

For IFFE interface, the max packet size is 1514 on NPGE(P) unit.


Range 64... 1518

Step 1

Units -



Default value 64


Related functions -




Related options -



References -

Table 79 lpPktSize (Link OAM Loopback Packet Size) (Cont.)

Parameter name Link OAM PDU Timer

Abbreviated name pduTimer

3GPP name -


Parameter group -

Table 80 pduTimer (Link OAM PDU Timer)

92 DN70257257



IOAMT Parameters

12.12 templateID (Template ID)

Classification -

Multiplicity 1

Description This parameter defines the time period of sending OAM PDU.


Range 100... 1000

Step 100

Units -



Default value 1000


Related functions -




Related options -



References -

Table 80 pduTimer (Link OAM PDU Timer) (Cont.)

Parameter name Template ID

Abbreviated name templateID

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the Ethernet OAM template in the system.

The identifier is part of

the distinguished name and it is formed in the following way: NE-x/IOAMT-tem-plateId. For example: RNC-02/IOAMT-1.

The corresponding MML command group: ZQAT, "Template ID".

Table 81 templateID (Template ID)

DN70257257 93



12.13 templateName (Ethernet OAM Template Name)

Range 1... 5

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 81 templateID (Template ID) (Cont.)

Parameter name Ethernet OAM Template Name

Abbreviated name templateName

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the template name which is used for OAM link.


Range 1...10

Step -

Units characters



Default value -


Table 82 templateName (Ethernet OAM Template Name)

94 DN70257257



IOAMT Parameters

Related functions -




Related options -



References -

Table 82 templateName (Ethernet OAM Template Name) (Cont.)

DN70257257 95

IP Configuration Plan Interface Parameters IOPF Parameters


13 IOPF Parameters

13.1 iopfId (IOPF Identifier)

13.2 rfc1583comp (RFC1583 Compatibility)

Parameter name IOPF Identifier

Abbreviated name iopfId

3GPP name -

Managed Object IOPF

Parameter group -

Classification -

Multiplicity 1

Description This parameter identifies the OSPF configuration entity in the system. There is only one instance in IPNO. The identifier is part of the distinguished name and it is formed in a following way: NE-x/IPNO-unitType-unitIndex/IOPF-x. For example: RNC-1/IPNO-OMU-0/IOPF-1. The corresponding MML command group: ZQKI.

Range 1... 1

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 83 iopfId (IOPF Identifier)

Parameter name RFC1583 Compatibility

Abbreviated name rfc1583comp

Table 84 rfc1583comp (RFC1583 Compatibility)

96 DN70257257



IOPF Parameters

13.3 routeId (Router Id)

3GPP name -

Managed Object IOPF

Parameter group -

Classification -

Multiplicity 1

Description This implementation of OSPF is based on RFC2178, which fixes some looping problems in an earlier specification of OSPF. If this implementation is running in the environment with OSPF implementations based on RFC1583 or earlier, this OSPF must run in the compatibility mode. This ensures backwards compatibility. The default value is "Yes" (enabled). Yes = RFC1583 compatibility is enabled. No = RFC1583 compatibility is disabled. The corresponding MML command group: ZQKS, "rfc1583compatibility".


Step -

Units -


gui ==> internal

No ==> 0

Yes ==> 1



Related functions -




Related options -



References -

Table 84 rfc1583comp (RFC1583 Compatibility) (Cont.)

Parameter name Router Id

Abbreviated name routeId

3GPP name -

Managed Object IOPF

Table 85 routeId (Router Id)

DN70257257 97



13.4 spfDelay (SPF Delay)

Parameter group -

Classification -

Multiplicity 1

Description The router identification is given in the form of an IP address. The Router ID spec-ifies a number that uniquely defines the router in a routing domain. Selecting an existing IP address in the unit as the OSPF router ID inherently makes it unique.

The IP network number of a subnetwork can be used as the area ID.

Set the router ID yourself and do not rely on the system to pick a router ID based on an IP address. This is to prevent the router ID from changing if the interface used for the router ID goes down.

Give the value as a dotted quad, for example [0-255].[0-255].[0-255].[0-255]. If you do not give a router ID, the router selects internally the highest interface address at the time of OSPF being enabled. The corresponding MML command: ZQKS, "router identification".

Do not use the 0.0.0.0 router ID, because by the 0.0.0.0 value the current router ID is taken out of use.

Range 7...15

Step -

Units characters



Default value -

Default value notes Default is empty.

Related functions -




Related options -



References -

Table 85 routeId (Router Id) (Cont.)

Parameter name SPF Delay

Abbreviated name spfDelay

Table 86 spfDelay (SPF Delay)

98 DN70257257



IOPF Parameters

13.5 spfHoldtime (SPF Holdtime)

3GPP name -

Managed Object IOPF

Parameter group -

Classification -

Multiplicity 1

Description The parameter defines the waiting time before recalculating the OSPF routing table after a change in the topology.

The corresponding MML command group: ZQKS, "spf delay".

Range 1... 60

Step 1

Units seconds



Default value 2


Related functions -




Related options -



References -

Table 86 spfDelay (SPF Delay) (Cont.)

Parameter name SPF Holdtime

Abbreviated name spfHoldtime

3GPP name -

Managed Object IOPF

Parameter group -

Classification -

Multiplicity 1

Table 87 spfHoldtime (SPF Holdtime)

DN70257257 99



Description This parameter defines the minimum time between the recalculations of the OSPF routing table.

The corresponding MML command group: ZQKS, "spf hold time".

Range 1... 60

Step 1

Units seconds



Default value 5


Related functions -




Related options -



References -

Table 87 spfHoldtime (SPF Holdtime) (Cont.)

100 DN70257257



IPBR Parameters

14 IPBR Parameters

14.1 committedBW (Committed BW)

14.2 committedDcnBW (Committed DCN BW)

Parameter name Committed BW

Abbreviated name committedBW

3GPP name -

Managed Object IPBR

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the committed BW for the IP based route.

Corresponding MML command: ZQRU, "committed bandwidth of ip based route".

There is one rule about related bandwidth parameters.

routeBW >= committedBW > committedDcnBW + committedSigBW

Range 0... 1000000

Step 1

Units kbps



Default value 0


Related functions -




Related options -



References -

Table 88 committedBW (Committed BW)

Parameter name Committed DCN BW

Table 89 committedDcnBW (Committed DCN BW)

DN70257257 101

IP Configuration Plan Interface Parameters IPBR Parameters


14.3 committedSigBW (Committed signal BW )

Abbreviated name committedDcnBW

3GPP name -

Managed Object IPBR

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the committed DCN bandwidth for IP based route.

The corresponding MML command: ZQRU, "committed bandwidth of DCN".



Range 0... 1000

Step 1

Units kbps



Default value 0


Related functions -




Related options -



References -

Table 89 committedDcnBW (Committed DCN BW) (Cont.)

Parameter name Committed signal BW

Abbreviated name committedSigBW

3GPP name -

Managed Object IPBR

Parameter group -

Classification -

Table 90 committedSigBW (Committed signal BW )

102 DN70257257



IPBR Parameters

14.4 ifcFlag (IP IFC Flag)

Multiplicity 1

Description This parameter defines the committed signaling bandwidth for ip based route.

The corresponding MML command: ZQRU, "committed signaling bandwidth".



Range 0... 50000

Step 1

Units kbps



Default value 0


Related functions -




Related options -



References -

Table 90 committedSigBW (Committed signal BW ) (Cont.)

Parameter name IP IFC Flag

Abbreviated name ifcFlag

3GPP name -

Managed Object IPBR

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines whether the internal flow control is used or not.

The corresponding MML command: ZQRU, "ifcmethod".

Range OFF (0), ON (1)

Step -

Table 91 ifcFlag (IP IFC Flag)

DN70257257 103



14.5 ipBasedRouteName (IP based route name)

Units -


gui ==> internal

OFF ==> 0

ON ==> 1

Default value OFF (0)


Related functions -




Related options -



References -

Table 91 ifcFlag (IP IFC Flag) (Cont.)

Parameter name IP based route name

Abbreviated name ipBasedRouteName

3GPP name -

Managed Object IPBR

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the name of the IP based route.

The IP based route name is unique in the RNC.

The corresponding MML command: ZQRU, "IP based route name".

Range 1...16

Step -

Units characters



Default value -


Table 92 ipBasedRouteName (IP based route name)

104 DN70257257



IPBR Parameters

14.6 ipbrId (IP based route id)

Related functions -




Related options -



References -

Table 92 ipBasedRouteName (IP based route name) (Cont.)

Parameter name IP based route id

Abbreviated name ipbrId

3GPP name -

Managed Object IPBR

Parameter group -

Classification -

Multiplicity 1

Description This parameter identifies the IP based route.

The IP based route id is unique in the RNC.

The identifier is part of the distinguished name and it is formed in the following way: NE-x/IPBR-ipbrId. For example: RNC-1/IPBR-1.

The corresponding MML command: ZQRU, "ip based route id".

Range 1... 4095

Step 1

Units -



Default value -


Related functions -




Table 93 ipbrId (IP based route id)

DN70257257 105



14.7 localMuxUDPPort (IP multiplexing local UDP port)

Related options -



References -

Table 93 ipbrId (IP based route id) (Cont.)

Parameter name IP multiplexing local UDP port

Abbreviated name localMuxUDPPort

3GPP name -

Managed Object IPBR

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the local UDP port for IP multiplexing.

The corresponding MML commands: QRU, QRL, "IP multiplexing local UDP port".

Range 49152... 65535

Step 1

Units -



Default value 65535


Related functions -




Related options • Efficient Transport for Small IP Packets



References -

Table 94 localMuxUDPPort (IP multiplexing local UDP port)

106 DN70257257



IPBR Parameters

14.8 maxMuxPackets (IP multiplexing max packets)

14.9 ratio (Ratio )

Parameter name IP multiplexing max packets

Abbreviated name maxMuxPackets

3GPP name -

Managed Object IPBR

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the maximum number of packets in one multiplexed packet for IP multiplexing.

The corresponding MML commands: QRU, QRL, "IP multiplexing max packets".

Range 1... 30

Step 1

Units -



Default value 30


Related functions -







References -

Table 95 maxMuxPackets (IP multiplexing max packets)

Parameter name Ratio

Abbreviated name ratio

3GPP name -

Managed Object IPBR

Table 96 ratio (Ratio )

DN70257257 107



14.10 remoteMuxUDPPort (IP multiplexing remote UDP port)

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the Ratio for Iur/(Iub+Iur).

The corresponding MML command: ZQRU,"ratio".

Range 0... 100

Step 1

Units -



Default value 20


Related functions -




Related options -



References -

Table 96 ratio (Ratio ) (Cont.)

Parameter name IP multiplexing remote UDP port

Abbreviated name remoteMuxUDPPort

3GPP name -

Managed Object IPBR

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the remote UDP port for IP multiplexing.

The corresponding MML commands: QRU, QRL, "IP multiplexing remote UDP port".

Range 49152... 65535

Table 97 remoteMuxUDPPort (IP multiplexing remote UDP port)

108 DN70257257



IPBR Parameters

14.11 routeBW (Route bandwidth)

Step 1

Units -



Default value 65535


Related functions -







References -

Table 97 remoteMuxUDPPort (IP multiplexing remote UDP port) (Cont.)

Parameter name Route bandwidth

Abbreviated name routeBW

3GPP name -

Managed Object IPBR

Parameter group -

Classification -

Multiplicity 1

Description This parameters defines the route bandwidth for IP based route.

The corresponding MML command: ZQRU, "route bandwidth of ip based route".



Range 0... 1000000

Step 1

Units kbps



Default value 0

Table 98 routeBW (Route bandwidth)

DN70257257 109



14.12 udpMuxDSCP (IP multiplexing DSCP value)


Related functions -




Related options -



References -

Table 98 routeBW (Route bandwidth) (Cont.)

Parameter name IP multiplexing DSCP value

Abbreviated name udpMuxDSCP

3GPP name -

Managed Object IPBR

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the DSCP value for IP multiplexing.

The corresponding MML commands: QRU, QRL, "IP multiplexing DSCP value".

Range 0... 63

Step 1

Units -



Default value 46


Related functions -






Table 99 udpMuxDSCP (IP multiplexing DSCP value)

110 DN70257257



IPBR Parameters

14.13 udpMuxEnabled (IP multiplexing flag)


References -

Table 99 udpMuxDSCP (IP multiplexing DSCP value) (Cont.)

Parameter name IP multiplexing flag

Abbreviated name udpMuxEnabled

3GPP name -

Managed Object IPBR

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines whether IP multiplexing is enabled or not.

The corresponding MML commands: QRU, QRL, "IP multiplexing".


Step -

Units -


gui ==> internal

Disable ==> 0

Enable ==> 1

Default value Disable (0)


Related functions -







References -

Table 100 udpMuxEnabled (IP multiplexing flag)

DN70257257 111

IP Configuration Plan Interface Parameters IPHB Parameters


15 IPHB Parameters

15.1 phbId (PHB profile Identifier)

Parameter name PHB profile Identifier

Abbreviated name phbId

3GPP name -

Managed Object IPHB

Parameter group -

Classification -

Multiplicity 1

Description This parameter identifies the PHB profile ID.

The profile id 0 is the default profile and it cannot be updated or deleted. It exists only in the upload file for planning purposes.

The profile id is unique in the RNC.

The identifier is part of the distinguished name and it is formed in the following way:

NE-x/IPHB-phbId. For example: RNC-1/IPHB-1.

The corresponding MML command group: ZQ8V, "profile id".

Range 0... 10

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 101 phbId (PHB profile Identifier)

112 DN70257257



IPHB Parameters

15.2 phbProfileName (PHB profile name)

15.3 profileList (PHB Profile List)

Parameter name PHB profile name

Abbreviated name phbProfileName

3GPP name -

Managed Object IPHB

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the PHB profile name.

The profile name 'DEFAULT' is the default profile and it cannot be updated or deleted. It exists only in the upload file for planning purposes.

The profile name is unique in the RNC.

The corresponding MML command group: ZQ8V, "profile name".

Range 1...20

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 102 phbProfileName (PHB profile name)

Parameter name PHB Profile List

Abbreviated name profileList

Table 103 profileList (PHB Profile List)

DN70257257 113



15.4 expWeig (Exponential weight factor)

3GPP name -

Managed Object IPHB

Parameter group -

Classification -

Multiplicity 6

Description This parameter defines the PHB profile.

The corresponding MML command group: ZQ8V.


-

Default value -


Related functions -

Child parameters • expWeig • length • maxDrop • maxThreshold • minThreshold • phb • quePriority • queWeight • schedule • vlanPri




Related options -



References -

Table 103 profileList (PHB Profile List) (Cont.)

Parameter name Exponential weight factor

Abbreviated name expWeig

3GPP name -

Table 104 expWeig (Exponential weight factor)

114 DN70257257



IPHB Parameters

15.5 length (Queue length)

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the exponential weight factor.

The corresponding MML command: ZQ8V, "Exponential weight factor."

Range 0... 0

Step 1

Units -



Default value 0


Related functions -




Related options -



References -

Table 104 expWeig (Exponential weight factor) (Cont.)

Parameter name Queue length

Abbreviated name length

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Table 105 length (Queue length)

DN70257257 115



15.6 maxDrop (Max drop value)

Description This parameter defines the queue length. The value is constant for different PHB values. The value is 500 for the BE PHB. The value is 300 for the AF1, AF2 and AF3 PHB. The value is 100 for the AF4 and EF profile.

Range 0... 500

Step 1

Units -



Default value -

Default value notes Default value is decided by PHB.

Related functions -




Related options -



References -

Table 105 length (Queue length) (Cont.)

Parameter name Max drop value

Abbreviated name maxDrop

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the WRED maximum drop probability value.

The corresponding MML command group: ZQ8V, "wred max drop probability".

Range 0... 100

Step 1

Units %

Table 106 maxDrop (Max drop value)

116 DN70257257



IPHB Parameters

15.7 maxThreshold (Max threshold)



Default value -


Related functions -




Related options -



References -

Table 106 maxDrop (Max drop value) (Cont.)

Parameter name Max threshold

Abbreviated name maxThreshold

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the WRED maximum thresholds.

For the current PHB, this value is always 100.


Range 100... 100

Step 1

Units %



Default value -


Related functions -


Table 107 maxThreshold (Max threshold)

DN70257257 117



15.8 minThreshold (Min threshold)



Related options -



References -

Table 107 maxThreshold (Max threshold) (Cont.)

Parameter name Min threshold

Abbreviated name minThreshold

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the WRED minimum thresholds.


Range 0... 100

Step 1

Units %



Default value -


Related functions -




Related options -



References -

Table 108 minThreshold (Min threshold)

118 DN70257257



IPHB Parameters

15.9 phb (PHB value)

Parameter name PHB value

Abbreviated name phb

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the PHB value.


Range BE (0), EF (1), AF1 (21), AF2 (22), AF3 (23), AF4 (24)

Step -

Units -


gui ==> internal

BE ==> 0

EF ==> 1

AF1 ==> 21

AF2 ==> 22

AF3 ==> 23

AF4 ==> 24

Default value -


Related functions -




Related options -



References -

Table 109 phb (PHB value)

DN70257257 119



15.10 quePriority (Queue priority)

15.11 queWeight (Queue weight)

Parameter name Queue priority

Abbreviated name quePriority

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the attribute of the queue whether it is RT or NRT.

This value is constant for the PHB. It is RT for PHB (AF4 and EF) and NRT for the other PHB.

Range NRT (0), RT (1)

Step -

Units -


gui ==> internal

NRT ==> 0

RT ==> 1

Default value -


Related functions -




Related options -



References -

Table 110 quePriority (Queue priority)

Parameter name Queue weight

Abbreviated name queWeight

3GPP name -

Table 111 queWeight (Queue weight)

120 DN70257257



IPHB Parameters

15.12 schedule (Queue schedule)

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the queue weight.

This value is not valid for the EF PHB, so it should skip in the dowload and upload file.

The corresponding MML command group: ZQ8V, "queue weight".

Range 1... 10000

Step 1

Units -



Default value -

Default value notes

Related functions -




Related options -



References -

Table 111 queWeight (Queue weight) (Cont.)

Parameter name Queue schedule

Abbreviated name schedule

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Table 112 schedule (Queue schedule)

DN70257257 121



15.13 vlanPri (Vlan priority)

Description This parameter defines the queue schedule type.

This value is constant for different PHB values. The value is SP for EF PHB, and WRR for other PHB.

Range WRR SCHED (2), SP SCHED (4)

Step -

Units -


gui ==> internal

WRR SCHED ==> 2

SP SCHED ==> 4

Default value -

Default value notes The default value is decided by PHB.

Related functions -




Related options -



References -

Table 112 schedule (Queue schedule) (Cont.)

Parameter name Vlan priority

Abbreviated name vlanPri

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the VLAN priority for this PHB value.

The corresponding MML command group: ZQ8V, "vlan priority". Even though this parameter can be modified On-Line, a new value is only taken into use after the next interface unit reset.

Range 0... 7

Table 113 vlanPri (Vlan priority)

122 DN70257257



IPHB Parameters

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 113 vlanPri (Vlan priority) (Cont.)

DN70257257 123

IP Configuration Plan Interface Parameters IPNO Parameters


16 IPNO Parameters

16.1 IPForwardingIPV4 (IP Forwarding flag)

Parameter name IP Forwarding flag

Abbreviated name IPForwardingIPV4

3GPP name -

Managed Object IPNO

Parameter group -

Classification -

Multiplicity 1

Description This parameter determines whether the TCP/IP stack forwards unicast IP packets that do not belong to it. If the parameters are configured for the first time, the default value is "OFF" for DMX unit; the default value is "ON" for CHORUS units; other-wise, the current value remains.

The parameter is used for the IPv4 stack configuration.

The corresponding MML command: ZQRT, "IP forwarding".


Step -

Units -


gui ==> internal

No ==> 0

Yes ==> 1

Default value -

Default value notes Default value is based on the unit type.

Related functions -




Related options -



References -

Table 114 IPForwardingIPV4 (IP Forwarding flag)

124 DN70257257



IPNO Parameters

16.2 defaultTTL (Default TTL)

16.3 hostName (Host name)

Parameter name Default TTL

Abbreviated name defaultTTL

3GPP name -

Managed Object IPNO

Parameter group -

Classification -

Multiplicity 1

Description The maximum time-to-live (hop count) value for an IP packet sourced by the system. Values range from zero to 254. The default value is 64 if configured for the first time, otherwise the current value remains.


The corresponding MML command group: ZQRT, "IP TTL".

Range 0... 254

Step 1

Units -



Default value 64


Related functions -




Related options -



References -

Table 115 defaultTTL (Default TTL)

Parameter name Host name

Abbreviated name hostName

3GPP name -

Table 116 hostName (Host name)

DN70257257 125



16.4 ipNodeId (IP Node Identifier)

Managed Object IPNO

Parameter group -

Classification -

Multiplicity 1

Description The name of the host computer for which you want to create either a fully qualified domain name (FQDN) or a name without the domain part. The name can contain the following characters: letters A-Z, numbers 0-9, and a hyphen (-). The maximum length of the name is 100 characters.


The corresponding MML command group: ZQRT, "host name".

Range 1...100

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 116 hostName (Host name) (Cont.)

Parameter name IP Node Identifier

Abbreviated name ipNodeId

3GPP name -

Managed Object IPNO

Parameter group -

Classification -

Multiplicity 1

Table 117 ipNodeId (IP Node Identifier)

126 DN70257257



IPNO Parameters

16.5 subnetsAreLocal (Subnets are local)

Description This parameter identifies the IP node entity in the system. The identifier is part of the distinguished name and is formed in the following way: NE-x/IPNO-unitType-unitIndex. For example: RNC-1/IPNO-OMU-0.

The corresponding MML command group: ZQRT.

Range 1...32

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 117 ipNodeId (IP Node Identifier) (Cont.)

Parameter name Subnets are local

Abbreviated name subnetsAreLocal

3GPP name -

Managed Object IPNO

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines whether subnets are considered to be local addresses. If not, only destination IP addresses on an attached subnetwork are considered local. The default value is 'YES' if parameters are configured for the first time, otherwise the current value remains. This parameter only exists in the DMX unit.


The corresponding MML command group: ZQRT, "Subnets are local".

Table 118 subnetsAreLocal (Subnets are local)

DN70257257 127




Step -

Units -


gui ==> internal

No ==> 0

Yes ==> 1



Related functions -




Related options -



References -

Table 118 subnetsAreLocal (Subnets are local) (Cont.)

128 DN70257257



IPRO Parameters

17 IPRO Parameters

17.1 ipBasedRoute (IP based route Entries)

Parameter name IP based route Entries

Abbreviated name ipBasedRoute

3GPP name -

Managed Object IPRO

Parameter group -

Classification -

Multiplicity 1800

Description Defines the IP based route network.

One unit can supports 1024 IP based routes at most.

The corresponding MML command is ZQRC;


-

Default value -


Related functions -

Child parameters • addrValueIPV4 • ipBasedRouteId • phbAF1 • phbAF2 • phbAF3 • phbAF4 • phbBE • phbEF


Related parameters iproListMode of IPRO

Parameter relationships The parameter has an effect on how the list is processed in the plan activation.

Related options -



References -

Table 119 ipBasedRoute (IP based route Entries)

DN70257257 129

IP Configuration Plan Interface Parameters IPRO Parameters


17.2 addrValueIPV4 (IP address )

17.3 ipBasedRouteId (IP based route id)

Parameter name IP address

Abbreviated name addrValueIPV4

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the IP address which is attached to the IP based route. The address is specified in the conventional dot notation (#.#.#.#).

The corresponding MML command group: ZQRC,"IP address".

Range 7...15

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 120 addrValueIPV4 (IP address )

Parameter name IP based route id

Abbreviated name ipBasedRouteId

3GPP name -

Managed Object -

Table 121 ipBasedRouteId (IP based route id)

130 DN70257257



IPRO Parameters

17.4 phbAF1 (PHB AF1)

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the IP based route to which this interface is attached.

The corresponding MML command group: ZQRC, "IP based route id".

Range 1... 4095

Step 1

Units -



Default value -

Default value notes Defualt value is not possible

Related functions -




Related options -



References -

Table 121 ipBasedRouteId (IP based route id) (Cont.)

Parameter name PHB AF1

Abbreviated name phbAF1

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Table 122 phbAF1 (PHB AF1)

DN70257257 131




Description PHB set is attached to the IP based route for VLAN traffic differentiation, and takes effect in VLAN configured site. Only the traffic whose type is within the PHB set will run on the specified IP based route. For example: "EF,AF4" is attached to IP based route "ipbr_1", "AF1,BE" is attached to IP based route "ipbr_2", then "voice" traffic will run on "ipbr_1" and BE traffic will run on "ipbr_2".

Note: PHB set is the combination of one or more of the PHB value. For example: "AF4, AF3, EF" or "AF1, BE".

This parameter determines whether PHB value "AF1" is available in the PHB set of the IP based route. The value of this parameter is "true" if PHB value "AF1" is avail-able in the PHB set, else "false". The corresponding MML command group: ZQRC,"PHBSet".

Range false (0), true (1)

Step -

Units -


• false => 0 • true => 1

Default value true (1)

Default value notes All PHB value("BE","AF4","AF3","AF2","AF1","EF") are available for the PHB set of the IP based route in default.

Related functions -


Related parameters phbBE of IPRO

phbAF4 of IPRO

phbAF3 of IPRO

phbAF2 of IPRO

phbEF of IPRO

Parameter relationships phbAF1 can not be set to "false" if phbBE,phbAF2,phbAF3,phbAF4 and phbEF are all set as "false". In other words, at least one of phbBE,phbAF1,phbAF2,phbAF3,phbAF4 and phbEF should be set to "true".

Related options -



References -

Table 122 phbAF1 (PHB AF1) (Cont.)



132 DN70257257



IPRO Parameters


3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description PHB set is attached to IP based route for VLAN traffic differentiation, and takes effect in VLAN configured site. Only the traffic whose type is within the PHB set will run on the specified IP based route. For example: "EF,AF4" is attached to IP based route "ipbr_1", "AF1,BE" is attached to IP based route "ipbr_2", then "voice" traffic will run on "ipbr_1" and BE traffic will run on "ipbr_2".


This parameter determines whether PHB value "AF2" is available in the PHB set of the IP based route. Value of this parameter is "true" if PHB value "AF2" is available in the PHB set, else "false". The corresponding MML command group: ZQRC,"PHBSet".


Step -

Units -


• false => 0 • true => 1



Related functions -



phbAF4 of IPRO

phbAF3 of IPRO

phbAF1 of IPRO

phbEF of IPRO


Related options -




DN70257257 133




References -




3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1





Step -

Units -


• false => 0 • true => 1



Related functions -



phbAF4 of IPRO

phbAF2 of IPRO

phbAF1 of IPRO

phbEF of IPRO


134 DN70257257



IPRO Parameters



Related options -



References -




3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1





Step -

Units -


• false => 0 • true => 1



Related functions -


DN70257257 135



17.8 phbEF (PHB EF)



phbAF3 of IPRO

phbAF2 of IPRO

phbAF1 of IPRO

phbEF of IPRO


Related options -



References -


Parameter name PHB EF

Abbreviated name phbEF

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1



This parameter determines whether PHB value "EF" is available in the PHB set of the IP based route. The value of this parameter is "true" if PHB value "EF" is avail-able in the PHB set, else "false". The corresponding MML command group: ZQRC,"PHBSet".


Step -

Table 126 phbEF (PHB EF)

136 DN70257257



IPRO Parameters

17.9 iproId (network interface Identifier)

Units -


• false => 0 • true => 1



Related functions -



phbAF4 of IPRO

phbAF3 of IPRO

phbAF2 of IPRO

phbAF1 of IPRO

Parameter relationships phbEF can not be set to "false" if phbBE,phbAF1,phbAF2,phbAF3 and phbAF4 are all set as "false". In other words, at least one of phbBE,phbAF1,phbAF2,phbAF3,phbAF4 and phbEF should be set to "true".

Related options -



References -

Table 126 phbEF (PHB EF) (Cont.)

Parameter name network interface Identifier

Abbreviated name iproId

3GPP name -

Managed Object IPRO

Parameter group -

Classification -

Multiplicity 1

Description This parameter identifies the network interface which configures the IP based route within the IP node entity in the system. The identifier is part of the distinguished name and it is formed in the following way: NE-x/IPNO-unitType-unitIndex/IPRO-ifName. For example: RNC-1/IPNO-NPGEP-0/IPRO-IFGE0.

The corresponding MML command group: ZQRC, "interface name".

Table 127 iproId (network interface Identifier)

DN70257257 137



17.10 iproListMode (IP Based Route id list update mode)

Range 3...8

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 127 iproId (network interface Identifier) (Cont.)

Parameter name IP Based Route id list update mode

Abbreviated name iproListMode

3GPP name -

Managed Object IPRO

Parameter group -

Classification -

Multiplicity 1

Table 128 iproListMode (IP Based Route id list update mode)

138 DN70257257



IPRO Parameters

Description This parameter determines which of the following two modes is used to update the IP-based route id list:

iproListMode:”Full”

The whole list structure is downloaded. This contains all the existing items received at the IP plan upload, as well as new IP-based route id entries. Items that exist in the IP layer configuration, but which are not included in the download plan list, are removed in the plan activation operation.

Note: In this mode, the whole IP-based route list is delivered in the IP plan. Items not included in the list are deleted from the IP layer configuration.

Note: If PHB set is not defined, all PHBs are set to 'true'.

iproListMode:”Add”

Only the new entries in the list structure are delivered, that is, only the newly added IP-based route id and IP address pairs are included in the list. The new items are added into the configuration, while the existing IP layer configuration remains unchanged. If an item to be added already exists in the configuration, there are 2 cases:

1. If PHB set is not defined, the existing item remains unchanged.

2. If PHB set is defined, the PHB set of existed item will be updated.

Note: Deletion of IP-based route id and IP address pairs is only supported in “Full” operation mode. Only one deletion plan at a time is sent and activated with an up-to-date list. All items that are to remain in the IP layer configuration must be included in the list.

The parameter value is not stored in the IP layer configuration; it is only used to determine the mode in which the IPRO-IPBasedRoute list is processed. When the parameter value is not included in the downloaded plan file, the default value (“Full”) is used by the network element. This parameter is not used in IPRO object creation.

Range Full (0), Add (1)

Step -

Units -


gui ==> internal

Full ==> 0

Add ==> 1

Default value Full (0)

Default value notes In the default mode “Full,” all existing entries that are not to be changed must be found from the list. Items that currently exist in the IP layer configuration, but which are not included in the list, are deleted.

Related functions -


Related parameters ipBasedRoute of IPRO

Parameter relationships This parameter detemines the way in which the list is processed in plan activation.

Table 128 iproListMode (IP Based Route id list update mode) (Cont.)

DN70257257 139



Related options -


Interfaces • RAC -> RNC • RACApp -> RAC

References -

Table 128 iproListMode (IP Based Route id list update mode) (Cont.)

140 DN70257257



IPRT Parameters

18 IPRT Parameters

18.1 ipRoutingTableId (IP Routing Table Identifier)

Parameter name IP Routing Table Identifier

Abbreviated name ipRoutingTableId

3GPP name -

Managed Object IPRT

Parameter group -

Classification -

Multiplicity 1

Description Identifies the IP routing table within the IP node entity in the system. There is only one IPRT within the IPNO.

Only the routing table on working unit is shown as an operational object and when configuring route entries it has to be done for the working unit, not for the spare unit.

The identifier is part of the distinguished name and it is formed in the following way: NE-x/IPNO-unitType-unitIndex/IPRT-1. For example: RNC-1/IPNO-OMU-0/IPRT-1.

The corresponding MML command group: ZQKC, ZQKA, ZQKB.

Range 1... 1

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 129 ipRoutingTableId (IP Routing Table Identifier)

DN70257257 141

IP Configuration Plan Interface Parameters IPRT Parameters


18.2 iprtListMode (IP static route list update mode)

Parameter name IP static route list update mode

Abbreviated name iprtListMode

3GPP name -

Managed Object IPRT

Parameter group -

Classification -

Multiplicity 1

Description This parameter determines which of the following two modes is used to update the IP static route list:

iprtListMode:”Full”

The whole list structure is downloaded. This contains all the existing items received at the IP plan upload, as well as the new IP static route entries. Items that exist in the IP layer configuration, but which are not included in the download plan list, are removed in the plan activation operation.

Note: In this mode, the whole IP static route list is delivered in the IP plan. Items not included in the list are deleted from the IP layer configuration.

iprtListMode:”Add”

Only the new entries in the list structure are delivered, that is, only the newly added IP static routes are included in the list. The new items are added into the configu-ration, while the existing IP layer configuration remains unchanged. If an item to be added already exists in the configuration, then the existing item remains unchanged.

Note: Deletion of IP static route entries is only supported in ”Full” operation mode. Only one deletion plan at a time is sent and activated with an up-to-date list. All items that are to remain in the IP layer configuration must be included in the list.

The parameter value is not stored in the IP layer configuration; it is only used to determine the mode in which the IPRT- routeEntriesIPV4 list is processed. When the parameter value is not included in the downloaded plan file, the default value (“Full”) is used by the network element. This parameter is not used in IPRT object creation.

Range Full (0), Add (1)

Step -

Units -


gui ==> internal

Full ==> 0

Add ==> 1

Default value Full (0)

Table 130 iprtListMode (IP static route list update mode)

142 DN70257257



IPRT Parameters

18.3 routeEntriesIPV4 (Route Entries for IPv4)

Default value notes In the default mode “Full,” all existing entries that are not to be changed must be found from the list. Items that currently exist in the IP layer configuration, but which are not included in the list, are deleted.

Related functions -


Related parameters routeEntriesIPV4 of IPRT

Parameter relationships This parameter determines the way in which the list is processed in plan activation.

Related options -


Interfaces • RAC -> RNC • RACApp -> RAC

References -

Table 130 iprtListMode (IP static route list update mode) (Cont.)

Parameter name Route Entries for IPv4

Abbreviated name routeEntriesIPV4

3GPP name -

Managed Object IPRT

Parameter group -

Classification -

Multiplicity 1024

Description Route entries for IPv4. The corresponding MML command group: ZQKC,ZQKG.

For destination address based route:

ZQKC:[<unit_type>,[<unit_index>]]:[<dst_ip_address>,<net-mask>]:[<gateway_ip_address>]: [<route_type>];

For source address based route:

ZQKC:[<unit_type>,[<unit_index>]]::[<gateway_ip_address>,<src_ip_address>,<netmask>]: [<route_type>];


-

Default value -


Related functions -

Table 131 routeEntriesIPV4 (Route Entries for IPv4)

DN70257257 143



18.4 bfdId (BFD session ID)

Child parameters • bfdId • destIPAddrIPV4 • gatewayIPV4 • netmask • preference • routeType • srcIPAddrIPV4


Related parameters iprtListMode of IPRT

Parameter relationships The parameter has an effect on how the list is processed in the plan activation.

Related options -



References -

Table 131 routeEntriesIPV4 (Route Entries for IPv4) (Cont.)

Parameter name BFD session ID

Abbreviated name bfdId

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description This parameter gets/sets the BFD session ID which is bound with the static route. Only the Single-Hop BFD sessions are supported.

If the static is not bound with the BFD session, the parameter will be 0.

The parameter is only valid for the destination address based route.

The corresponding MML command: ZQKG,ZQKB

Range 0... 3000

Step 1

Units -



Default value 0

Table 132 bfdId (BFD session ID)

144 DN70257257



IPRT Parameters

18.5 destIPAddrIPV4 (Destination IPv4 address)


Related functions -




Related options -



References -

Table 132 bfdId (BFD session ID) (Cont.)

Parameter name Destination IPv4 address

Abbreviated name destIPAddrIPV4

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description The route's destination IP address or IP subnetwork. The address is specified in the conventional dot notation (#.#.#.#). The parameter range for each part of the address is from zero to 255.

For default static route, destIPAddrIPV4 is (0.0.0.0) and netmask is( 255.255.255.255).

For source based static route, fill correct srcIPAddrIPV4 and netmaks, keep destIPAddrIPV4 (0.0.0.0).

The corresponding MML command: ZQKC, "destination IP address".

Range 7...15

Step -

Units characters



Default value -


Related functions -

Table 133 destIPAddrIPV4 (Destination IPv4 address)

DN70257257 145



18.6 gatewayIPV4 (Gateway IPv4 address)




Related options -



References -

Table 133 destIPAddrIPV4 (Destination IPv4 address) (Cont.)

Parameter name Gateway IPv4 address

Abbreviated name gatewayIPV4

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description The IP address of the gateway. The address is specified in the conventional dot notation (#.#.#.#). The parameter range for each part of the address is from zero to 255. This parameter is obligatory.

The corresponding MML command group: ZQKC, "gateway IP address".

Range 7...15

Step -

Units characters



Default value -


Related functions -




Related options -


Table 134 gatewayIPV4 (Gateway IPv4 address)

146 DN70257257



IPRT Parameters



References -

Table 134 gatewayIPV4 (Gateway IPv4 address) (Cont.)



3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description Netmask used for the static route.

For the destination based route, it is the netmask of destIPAddrIPV4.

For the source based route, it is the netmask of srcIPAddrIPV4.

For the default static route, netmask is (255.255.255.255) and keep destIPAddrIPV4 as (0.0.0.0).

The corresponding MML command group: ZQKC, "netmask".

Range 7...15

Step -

Units characters



Default value -


Related functions -




Related options -



References -


DN70257257 147



18.8 preference (Preference)

18.9 routeType (Route type)

Parameter name Preference

Abbreviated name preference

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description Router preference is used to configure different route priority.

Only destination address based route is supported.

The corresponding MML command: ZQKC,ZQKB

Range 0... 255

Step 1

Units -



Default value 0


Related functions -




Related options -



References -

Table 136 preference (Preference)

Parameter name Route type

Abbreviated name routeType

3GPP name -

Managed Object -

Table 137 routeType (Route type)

148 DN70257257



IPRT Parameters

18.10 srcIPAddrIPV4 (Source IPv4 address)

Parameter group -

Classification -

Multiplicity 1

Description The route type for the static route to be created.

Physical: A route that uses a physical address to reach its gateway. A physical route is always present in the unit it is configured.

Logical: A route that uses a logical address to reach its gateway. The route follows the logical address if a switchover occurs.

The corresponding MML command group: ZQKC, "route type".

Range Physical (0), Logical (1)

Step -

Units -


gui ==> internal

Physical ==> 0

Logical ==> 1

Default value -

Default value notes For NPGE, Default value is Physical (0).For NPGEP,Default value is Logical (1).

Related functions -




Related options -



References -

Table 137 routeType (Route type) (Cont.)

Parameter name Source IPv4 address

Abbreviated name srcIPAddrIPV4

3GPP name -

Managed Object -

Parameter group -

Classification -

Table 138 srcIPAddrIPV4 (Source IPv4 address)

DN70257257 149



Multiplicity 1

Description The route's source IP address or IP subnetwork. The address is specified in the conventional dot notation (#.#.#.#). The parameter range for each part of the address is from zero to 255.

For the default static route, destIPAddrIPV4 is (0.0.0.0), netmask is( 255.255.255.255), and keep srcIPAddrIPV4 blank.

For the destination based static route, destIPAddrIPV4 is like(X.X.X.X), netmask is like (255.255.x.x) and keep srcIPAddrIPV4 blank.

For the source based static route, srcIPAddrIPV4 is like(X.X.X.X), netmask is like (255.255.x.x) and keep destIPAddrIPV4 as (0.0.0.0).

Range 7...15

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 138 srcIPAddrIPV4 (Source IPv4 address) (Cont.)

150 DN70257257



IQOS Parameters

19 IQOS Parameters

19.1 dspmProfileId (DSPM profile id)

19.2 dspmProfileName (DSPM profile name)

Parameter name DSPM profile id

Abbreviated name dspmProfileId

3GPP name -

Managed Object IQOS

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the DSPM profile to which the interface is attached.

The corresponding MML command: ZQ8S, "dspm profile id".

Range 0... 10

Step 1

Units -



Default value 0

Default value notes The default id is the former configured id for the interface otherwise default id is 0.

Related functions -




Related options -



References -

Table 139 dspmProfileId (DSPM profile id)

Parameter name DSPM profile name

Abbreviated name dspmProfileName

3GPP name -

Table 140 dspmProfileName (DSPM profile name)

DN70257257 151

IP Configuration Plan Interface Parameters IQOS Parameters


19.3 iqosId (Qos interface)

Managed Object IQOS

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the DSPM profile to which the interface is attached.

The corresponding MML command: ZQ8S, "dspm profile name".

Range 1...20

Step -

Units characters



Default value DEFAULT

Default value notes The default name is the former configured name for the interface otherwise default id is "DEFAULT".

Related functions -




Related options -



References -

Table 140 dspmProfileName (DSPM profile name) (Cont.)

Parameter name Qos interface

Abbreviated name iqosId

3GPP name -

Managed Object IQOS

Parameter group -

Classification -

Multiplicity 1

Table 141 iqosId (Qos interface)

152 DN70257257



IQOS Parameters

19.4 phbProfileId (PHB profile id)

Description This parameter identifies the Ethernet interface which is used for the QoS configu-ration in the system. The identifier is part of the distinguished name and it is formed in the following way: NE-x/IPNO-unitType-unitIndex/IQOS-ifName. For example: RNC-1/IPNO-NPGEP-0/IQOS-IFGE0.

The corresponding MML command: ZQ8S,"interface name".

Range 3...8

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 141 iqosId (Qos interface) (Cont.)

Parameter name PHB profile id

Abbreviated name phbProfileId

3GPP name -

Managed Object IQOS

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the phb profile to which the interface is attached.

The corresponding MML command: ZQ8S, "phb profile id".

Range 0... 10

Step 1

Units -

Table 142 phbProfileId (PHB profile id)

DN70257257 153



19.5 phbProfileName (PHB profile name)



Default value 0

Default value notes The default id is the former configured id for the interface otherwise default id is 0.

Related functions -




Related options -



References -

Table 142 phbProfileId (PHB profile id) (Cont.)

Parameter name PHB profile name

Abbreviated name phbProfileName

3GPP name -

Managed Object IQOS

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the name of the phb profile to which the interface is attached.

The corresponding MML command: ZQ8S, "phb profile name".

Range 1...20

Step -

Units characters



Default value DEFAULT

Default value notes The default name is the former configured name for the interface otherwise default id is "DEFAULT".

Related functions -


Table 143 phbProfileName (PHB profile name)

154 DN70257257



IQOS Parameters

19.6 status (Status)



Related options -



References -

Table 143 phbProfileName (PHB profile name) (Cont.)

Parameter name Status

Abbreviated name status

3GPP name -

Managed Object IQOS

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the diffServ configuration for the IP interface.

DiffServ Disable for IP interface means that all the traffic to or from the interface is treated as BE traffic.

The corresponding MML command group: ZQ8S, "enable or disable".


Step -

Units -


gui ==> internal

Disable ==> 0

Enable ==> 1



Related functions -




Related options -


Table 144 status (Status)

DN70257257 155




References -

Table 144 status (Status) (Cont.)

156 DN70257257



ISBFP Parameters

20 ISBFP Parameters

20.1 desiredMinTx (Min transmission interval)

20.2 detectMult (Detection multiplier)

Parameter name Min transmission interval

Abbreviated name desiredMinTx

3GPP name -

Managed Object ISBFP

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the minimum interval between two transmitted control packets.

The corresponding MML command : ZYGP,"minimum TX interval".

Range 50... 5000

Step 50

Units -



Default value 250

Default value notes The unit is milliseconds.

Related functions -




Related options -



References -

Table 145 desiredMinTx (Min transmission interval)

Parameter name Detection multiplier

Abbreviated name detectMult

Table 146 detectMult (Detection multiplier)

DN70257257 157

IP Configuration Plan Interface Parameters ISBFP Parameters


20.3 dscp (DSCP)

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Description This parameter indicates the number of control packets that the RNC will lose before the BFD session is declared down.

The corresponding MML command group: ZYGP, "detect multi".

Range 2... 10

Step 1

Units -



Default value 5


Related functions -




Related options -



References -

Table 146 detectMult (Detection multiplier) (Cont.)

Parameter name DSCP

Abbreviated name dscp

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Table 147 dscp (DSCP)

158 DN70257257



ISBFP Parameters

20.4 holdupTime (Holdup Time)

Description This parameter defines the DSCP value.

The corresponding MML command: ZYGP.

Range 0... 63

Step 1

Units -



Default value 48


Related functions -




Related options -



References -

Table 147 dscp (DSCP) (Cont.)

Parameter name Holdup Time

Abbreviated name holdupTime

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Description After BFD session state changes to UP, the subscribed service, such as static route, will be affected after Holdup Time.

The corresponding MML command: ZYGP.

Range 0... 900

Step 1

Units -

Table 148 holdupTime (Holdup Time)

DN70257257 159



20.5 profileId (ISBFP identifier)



Default value 0


Related functions -




Related options -



References -

Table 148 holdupTime (Holdup Time) (Cont.)

Parameter name ISBFP identifier


3GPP name -


Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the Single-hop BFD profile in the system. The default profile with the profile id "0" cannot be udpated or deleted. It exists only in the upload file and is returned for planning purposes. The identifier is part of the distin-guished name and it is formed in the following way: NE-x/IBFP-profileId. For example: RNC-02/ISBFP-1.

The corresponding MML command group: ZYGP, "profile id".

Range 0... 7

Step 1

Units -



Default value -


Table 149 profileId (ISBFP identifier)

160 DN70257257



ISBFP Parameters

20.6 profileName (Single-hop BFD Profile Name)

Related functions -




Related options -



References -

Table 149 profileId (ISBFP identifier) (Cont.)

Parameter name Single-hop BFD Profile Name

Abbreviated name profileName

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the name of the single-hop BFD profile.

The different profiles can use the same name.

MML command ZYGP is used in the Single-Hop profile.

Range 1...10

Step -

Units characters



Default value UNDEFINED


Related functions -




Related options -


Table 150 profileName (Single-hop BFD Profile Name)

DN70257257 161



20.7 requiredMinRx (Required minimum reception interval)


References -

Table 150 profileName (Single-hop BFD Profile Name) (Cont.)

Parameter name Required minimum reception interval

Abbreviated name requiredMinRx

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the minimum required interval between two received control packets.

The corresponding MML command: ZYGP,"minimum RX interval".

Range 50... 5000

Step 50

Units -



Default value 250

Default value notes The unit is milliseconds.

Related functions -




Related options -



References -

Table 151 requiredMinRx (Required minimum reception interval)

162 DN70257257



ISPF Parameters

21 ISPF Parameters

21.1 areaId (Area Identification)

21.2 interfaceEntries (Interface Entries)

Parameter name Area Identification

Abbreviated name areaId

3GPP name -

Managed Object ISPF

Parameter group -

Classification -

Multiplicity 1

Description The area ID for a new OSPF area.

The area ID is given as a dotted quad, for example, [0-255].[0-255].[0-255].[0-255]. The area ID of 0.0.0.0 is reserved for the backbone. The IP network number of a subnetwork can be used as the area ID. The corresponding MML command : ZQKE, "area identification".

Range 7...15

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 152 areaId (Area Identification)

Parameter name Interface Entries

Table 153 interfaceEntries (Interface Entries)

DN70257257 163

IP Configuration Plan Interface Parameters ISPF Parameters


21.3 cost (Cost)

Abbreviated name interfaceEntries

3GPP name -

Managed Object ISPF

Parameter group -

Classification -

Multiplicity 1500

Description Defines the OSPF interface list.


-

Default value -


Related functions -

Child parameters • cost • deadInterval • helloInterval • interfaceName • passive • password • priority • type




Related options -



References -

Table 153 interfaceEntries (Interface Entries) (Cont.)

Parameter name Cost

Abbreviated name cost

3GPP name -

Managed Object -

Parameter group -

Table 154 cost (Cost)

164 DN70257257



ISPF Parameters

21.4 deadInterval (Dead Interval)

Classification -

Multiplicity 1

Description The weight of a given path in a route. The higher the cost, the less preferred the link. You can explicitly override this in route redistribution. For example, to use one interface over another for routing paths, give one a higher cost. The corresponding MML command group: ZQKF, "ospf cost".

Range 1... 65535

Step 1

Units -



Default value 1


Related functions -




Related options -



References -

Table 154 cost (Cost) (Cont.)

Parameter name Dead Interval

Abbreviated name deadInterval

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Table 155 deadInterval (Dead Interval)

DN70257257 165



21.5 helloInterval (Hello Interval)

Description The length of being unable to hear a router's hello packets before the router declares that the neighbour is down.

The length is given in seconds. Typically, the value of this field must be four times the size of the hello interval. For a given link, this field must be the same on all routers, otherwise adjacencies are not formed. The corresponding MML command group: ZQKF, "router dead interval".

Range 1... 65535

Step 1

Units -



Default value 40


Related functions -




Related options -



References -

Table 155 deadInterval (Dead Interval) (Cont.)

Parameter name Hello Interval

Abbreviated name helloInterval

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description The length between hello packets sent by the router on the interface. The length is given in seconds. For a given link, this field must be the same on all routers, other-wise adjacencies are not formed. The corresponding MML command group: ZQKF, "hello interval".

Range 1... 65535

Table 156 helloInterval (Hello Interval)

166 DN70257257



ISPF Parameters

21.6 interfaceName (Interface Name)

Step 1

Units -



Default value 10


Related functions -




Related options -



References -

Table 156 helloInterval (Hello Interval) (Cont.)

Parameter name Interface Name

Abbreviated name interfaceName

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the name of the interface, given as a character string of maximum 8 characters. Only attached interfaces can be used. The corresponding MML command: ZQKF, "interface identification".

Range 3...8

Step -

Units characters



Default value -


Table 157 interfaceName (Interface Name)

DN70257257 167



21.7 passive (Passive)

Related functions -




Related options -



References -

Table 157 interfaceName (Interface Name) (Cont.)

Parameter name Passive

Abbreviated name passive

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description An interface that is put into passive mode will not send hello packets out of the given interface. This means no adjacencies will be formed on the link. The purpose of this mode is to enable the network associated with the interface to be included in the intra-area route calculation as opposed to redistributing the network into OSPF and having it as an ASE. In the passive mode, all interface configuration information, with the exception of the associated area and the cost, are ignored.

Y = Suppress hello packets.

N = Do not suppress hello packets.

The corresponding MML command: ZQKF, "passive".

Range No suppress mode (0), Suppress mode (1)

Step -

Units -


gui ==> internal

No suppress mode ==> 0

Suppress mode ==> 1

Default value No suppress mode (0)


Table 158 passive (Passive)

168 DN70257257



ISPF Parameters

21.8 password (Password)

Related functions -




Related options -



References -

Table 158 passive (Passive) (Cont.)

Parameter name Password

Abbreviated name password

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description If you set the authentication type to SIMPLE, a password is required. If it is SIMPLE, the password is an American Standard Code for Information Interchange (ASCII) string of 1 to 8 characters.

The password is to be given inside quotes. The corresponding MML command group: ZQKF, "password".

Range 1...8

Step -

Units characters



Default value -


Related functions -




Related options -

Table 159 password (Password)

DN70257257 169



21.9 priority (Priority)



References -

Table 159 password (Password) (Cont.)

Parameter name Priority

Abbreviated name priority

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description The priority for becoming the Designated Router (DR) on this link.

When two routers are attached to a network and both attempt to become a desig-nated router, the one with the highest priority wins. If there is currently an elected DR on the link, it remains the DR regardless of the configured priority. This is to prevent changing the DR too often. This field is relevant only on a shared-media interface (Ethernet), as a DR is not elected on point-to-point type interfaces. A router with 0 priority is not eligible to become the DR. The corresponding MML command group: ZQKF, "election priority".

Range 0... 255

Step 1

Units -



Default value 0


Related functions -




Related options -


Table 160 priority (Priority)

170 DN70257257



ISPF Parameters

21.10 type (Type)


References -

Table 160 priority (Priority) (Cont.)

Parameter name Type


3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description The type of authentication scheme to use for a given OSPF interface. Routers on a given link must agree on the authentication configuration in order to form neigh-bour adjacencies. This is used to guarantee that routing information is accepted only from trusted routers.

NONE = No authentitacion used.

SIMPLE = Simple password authentication.

The corresponding MML command group: ZQKF, "authentication".

Range NONE (0), SIMPLE (1)

Step -

Units -


gui ==> internal

NONE ==> 0

SIMPLE ==> 1

Default value NONE (0)


Related functions -




Related options -



Table 161 type (Type)

DN70257257 171



21.11 ispfId (ISPF Identifier)

21.12 networkPrefixEntries (Network Prefix Entries)

References -


Parameter name ISPF Identifier

Abbreviated name ispfId

3GPP name -

Managed Object ISPF

Parameter group -

Classification -

Multiplicity 1

Description Identifies the OSPF configuration entity related to the IPNO in the system. The identifier is part of the distinguished name and it is formed in the following way: NE-x/IPNO-unitType-unitIndex/ISPF-x. For example: RNC-1/IPNO-OMU-0/ISPF-1. The corresponding MML command group: ZQKE.

Range 0... 65535

Step 1

Units -



Default value -


Related functions -




Related options -


Interfaces • RNC -> RAC • RAC <-> RACApp

References -

Table 162 ispfId (ISPF Identifier)

Parameter name Network Prefix Entries

Table 163 networkPrefixEntries (Network Prefix Entries)

172 DN70257257



ISPF Parameters

21.13 maskLength (Mask Length)

Abbreviated name networkPrefixEntries

3GPP name -

Managed Object ISPF

Parameter group -

Classification -

Multiplicity 8

Description Defines the network prefix list to an OSPF area.


-

Default value -


Related functions -

Child parameters • maskLength • networkPrefix • restriction




Related options -



References -

Table 163 networkPrefixEntries (Network Prefix Entries) (Cont.)

Parameter name Mask Length

Abbreviated name maskLength

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description The mask length of the advertised address range. The corresponding MML command: ZQKH, "network prefix mask length".

Table 164 maskLength (Mask Length)

DN70257257 173



21.14 networkPrefix (Network Prefix)

Range 1... 32

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 164 maskLength (Mask Length) (Cont.)

Parameter name Network Prefix

Abbreviated name networkPrefix

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description Any area can be configured with multiple address ranges. These ranges are used to potentially reduce the number of routing entries that a given area emits into the backbone, and this way all areas. If a given prefix aggregates a number of more specific prefixes within an area, an address range can be configured and is the only prefix advertised into the backbone. Configure an address range that covers parts of a prefix that are not contained within the area with care.

Give the value as a dotted quad, for example '[0-255].[0-255].[0-255].[0-255]'. If you do not give a router ID, the router selects internally the highest interface address at the time of OSPF being enabled. The corresponding MML command group: ZQKH, "network prefix".

Range 7...15

Table 165 networkPrefix (Network Prefix)

174 DN70257257



ISPF Parameters

21.15 restriction (Restriction)

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 165 networkPrefix (Network Prefix) (Cont.)

Parameter name Restriction

Abbreviated name restriction

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description If an address range has marked restrict, no advertisement is injected into the back-bone. The default value is Yes (advertised).

Yes = Summary LSAs are advertised.

No = No summary LSAs are advertised.

The corresponding MML command group: ZQKH, "network prefix restriction".


Step -

Units -

Table 166 restriction (Restriction)

DN70257257 175



21.16 networkStubEntries (Network Stub Entries)


gui ==> internal

No ==> 0

Yes ==> 1



Related functions -




Related options -



References -

Table 166 restriction (Restriction) (Cont.)

Parameter name Network Stub Entries

Abbreviated name networkStubEntries

3GPP name -

Managed Object ISPF

Parameter group -

Classification -

Multiplicity 8

Description Defines the stub network list to an OSPF area.


-

Default value -


Related functions -

Child parameters • cost • stubNetwork • stubPrefixLength



Table 167 networkStubEntries (Network Stub Entries)

176 DN70257257



ISPF Parameters

21.17 cost (Cost)


Related options -



References -

Table 167 networkStubEntries (Network Stub Entries) (Cont.)

Parameter name Cost

Abbreviated name cost

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description The cost that the stub network must be advertised with. The corresponding MML command group: ZQKJ, "stub network cost".

Range 1... 65535

Step 1

Units -



Default value 1


Related functions -




Related options -



References -

Table 168 cost (Cost)

DN70257257 177



21.18 stubNetwork (Stub Network)

21.19 stubPrefixLength (stub netmask )

Parameter name Stub Network

Abbreviated name stubNetwork

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description The OSPF can advertise reachability to addresses that are not running the OSPF to indicate reachability. This can include remote addresses of point-to-point links or additional addresses configured on the router that are not directly running OSPF. Give the stub host as dotted quad, for example, '[0-255].[0-255].[0-255].[0-255]'. The corresponding MML command group: ZQKJ, "stub host".

Range 7...15

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 169 stubNetwork (Stub Network)

Parameter name stub netmask

Abbreviated name stubPrefixLength

3GPP name -

Table 170 stubPrefixLength (stub netmask )

178 DN70257257



ISPF Parameters

21.20 routeCost (Route Cost)

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description The parameter defines mask length of the stub network address range. The corre-sponding MML command group: ZQKH, "stub network mask length".

Range 1... 32

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 170 stubPrefixLength (stub netmask ) (Cont.)

Parameter name Route Cost

Abbreviated name routeCost

3GPP name -

Managed Object ISPF

Parameter group -

Classification -

Multiplicity 1

Description The cost of injecting a default route into the stub. This parameter applies only to a stub area. This parameter can also be called the stub default cost. The correspond-ing MML command group: ZQKE, "stub area route cost". It exists only when it is a stub Area.

Table 171 routeCost (Route Cost)

DN70257257 179



21.21 stubArea (Stub Area)

Range 1... 65535

Step 1

Units -



Default value 1


Related functions -




Related options -



References -

Table 171 routeCost (Route Cost) (Cont.)

Parameter name Stub Area

Abbreviated name stubArea

3GPP name -

Managed Object ISPF

Parameter group -

Classification -

Multiplicity 1

Description The stub area parameter block is required only if the area identification specifies a non-backbone area.

The stub area parameter specifies an area in which there are no Autonomous System External (ASE) routes. ASE routes are routes to destinations external to the AS. If this parameter is set to yes, the area must be a stub, so the external routing capability is disabled. The default value is N.

Y = Stub area.

N = Not a stub area.

The corresponding MML command group: ZQKE, "stub area".

Range N (0), Y (1)

Table 172 stubArea (Stub Area)

180 DN70257257



ISPF Parameters

21.22 stubbyArea (Stubby Area)

Step -

Units -


gui ==> internal

N ==> 0

Y ==> 1

Default value N (0)


Related functions -




Related options -



References -

Table 172 stubArea (Stub Area) (Cont.)

Parameter name Stubby Area

Abbreviated name stubbyArea

3GPP name -

Managed Object ISPF

Parameter group -

Classification -

Multiplicity 1

Description An area in which there are no ASE routes and summary routes. This parameter applies only to a stub area. The default value is N.

Y= Totally stubby area.

N = Not a totally stubby area.

The corresponding MML command group: ZQKE, "totally stubby area".

Range N (0), Y (1)

Step -

Units -

Table 173 stubbyArea (Stubby Area)

DN70257257 181



21.23 virLinkEntries (Virtual Link Entries)


gui ==> internal

N ==> 0

Y ==> 1

Default value N (0)


Related functions -




Related options -



References -

Table 173 stubbyArea (Stubby Area) (Cont.)

Parameter name Virtual Link Entries

Abbreviated name virLinkEntries

3GPP name -

Managed Object ISPF

Parameter group -

Classification -

Multiplicity 8

Description OSPF virtual link list


-

Default value -


Related functions -

Child parameters • deadInterval • helloInterval • password • remoteRouteId • type


Table 174 virLinkEntries (Virtual Link Entries)

182 DN70257257



ISPF Parameters

21.24 deadInterval (Dead Interval)



Related options -



References -

Table 174 virLinkEntries (Virtual Link Entries) (Cont.)

Parameter name Dead Interval

Abbreviated name deadInterval

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description The length of being unable to hear a router's hello packets before the router declares that the neighbour is down. The length is given in seconds. This field must be the same on the other end of the virtual link. The value of the router dead interval has to be bigger than the hello interval. The corresponding MML command group: ZQKV, "router dead interval".

Range 1... 65535

Step 1

Units -



Default value 120


Related functions -




Related options -


Table 175 deadInterval (Dead Interval)

DN70257257 183



21.25 helloInterval (Hello Interval)


References -

Table 175 deadInterval (Dead Interval) (Cont.)

Parameter name Hello Interval

Abbreviated name helloInterval

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description The length between hello packets sent by the router on the interface. The length is given in seconds. This field must be the same on the other end of the virtual link. The corresponding MML command group: ZQKV, "hello interval".

Range 1... 65535

Step 1

Units -



Default value 30


Related functions -




Related options -



References -

Table 176 helloInterval (Hello Interval)

184 DN70257257



ISPF Parameters

21.26 password (Password)

21.27 remoteRouteId (Remote Route Id)

Parameter name Password

Abbreviated name password

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description If you set the authentication type to SIMPLE, a password is required. If it is SIMPLE, the password is an ASCII string of 1 to 8 characters.

The corresponding MML command: ZQKV, "password".

Range 1...8

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 177 password (Password)

Parameter name Remote Route Id

Abbreviated name remoteRouteId

3GPP name -

Managed Object -

Table 178 remoteRouteId (Remote Route Id)

DN70257257 185



21.28 type (type)

Parameter group -

Classification -

Multiplicity 1

Description The router ID of the remote endpoint of the virtual link. The corresponding MML command group: ZQKV, "router identification".

Range 7...15

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 178 remoteRouteId (Remote Route Id) (Cont.)

Parameter name type


3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Table 179 type (type)

186 DN70257257



ISPF Parameters

Description An interface that is put into passive mode will not send hello packets out of The type of authentication scheme to use for the virtual link. In general, routers on a given link must agree on the authentication configuration in order to form neighbour adja-cencies. This is used to guarantee that routing information is accepted only from trusted routers. NONE = No authentitacion used. SIMPLE = Simple password authentication. The corresponding MML command group: ZQKV, "authentication".

Range NONE (0), SIMPLE (1)

Step -

Units -


gui ==> internal

NONE ==> 0

SIMPLE ==> 1

Default value NONE (0)


Related functions -




Related options -



References -

Table 179 type (type) (Cont.)

DN70257257 187

IP Configuration Plan Interface Parameters ISPRT Parameters


22 ISPRT Parameters

22.1 interfaceEntries (Interface Entries)

22.2 ifName (Interface Name)

Parameter name Interface Entries

Abbreviated name interfaceEntries

3GPP name -

Managed Object ISPRT

Parameter group -

Classification -

Multiplicity 64

Description Defines the interface list which is redistributed into the OSPF.


-

Default value -


Related functions -

Child parameters • ifName • metric




Related options -



References -

Table 180 interfaceEntries (Interface Entries)

Parameter name Interface Name

Abbreviated name ifName

3GPP name -

Managed Object -

Parameter group -

Table 181 ifName (Interface Name)

188 DN70257257



ISPRT Parameters

22.3 metric (Metric)

Classification -

Multiplicity 1

Description This parameter defines the interface name which is redistributed into the OSPF. The corresponding MML command: ZQKU.

If ALL is given, all valid interface routes are redistributed.

Range 3...8

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 181 ifName (Interface Name) (Cont.)

Parameter name Metric

Abbreviated name metric

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the cost for the redistribution.

The corresponding MML command group: ZQKU,"metric".

Range 1... 16777215

Step 1

Table 182 metric (Metric)

DN70257257 189



22.4 isprtId (ISPRT identifier)

Units -



Default value 1


Related functions -




Related options -



References -

Table 182 metric (Metric) (Cont.)

Parameter name ISPRT identifier

Abbreviated name isprtId

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Description Identifies the OSPF redistribution configuration in the system. There is only one instance in one IPNO. The identifier is part of the distinguished name and is formed in the following way: NE-x/IPNO-unitType-unitIndex/ISPRT-x. For example: RNC-1/IPNO-OMU-0/ISPRT-1. The corresponding MML command group: ZQKU.

Range 1... 1

Step 1

Units -



Default value -

Default value notes default value is not possible

Related functions -

Table 183 isprtId (ISPRT identifier)

190 DN70257257



ISPRT Parameters

22.5 redistAllEntries (Redistribute Entries)




Related options -



References -

Table 183 isprtId (ISPRT identifier) (Cont.)

Parameter name Redistribute Entries

Abbreviated name redistAllEntries

3GPP name -


Parameter group -

Classification -

Multiplicity 2

Description Defines the redistribute all list.


-

Default value -


Related functions -

Child parameters • metric • type




Related options -



References -

Table 184 redistAllEntries (Redistribute Entries)

DN70257257 191




22.7 type (Type)



3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1



Range 1... 16777215

Step 1

Units -



Default value 1


Related functions -




Related options -



References -


Parameter name Type


3GPP name -

Managed Object -

Parameter group -

Table 186 type (Type)

192 DN70257257



ISPRT Parameters

22.8 routeEntries (Route Entries)

Classification -

Multiplicity 1

Description This parameter defines the type which redistributes all valid static route or all valid interface routes into OSPF.

The corresponding MML command group: ZQKU.

Range Static route (0), Interface (1)

Step -

Units -


gui ==> internal

Static route ==> 0

Interface ==> 1

Default value -


Related functions -




Related options -



References -


Parameter name Route Entries

Abbreviated name routeEntries

3GPP name -


Parameter group -

Classification -

Multiplicity 64

Description Defines the redistribute static route list which is redistributed into the OSPF.


-

Table 187 routeEntries (Route Entries)

DN70257257 193



22.9 destIPAddrIPV4 (DestIPAddrIPV4)

Default value -


Related functions -

Child parameters • destIPAddrIPV4 • gatewayIPV4 • metric • netmask




Related options -



References -

Table 187 routeEntries (Route Entries) (Cont.)

Parameter name DestIPAddrIPV4

Abbreviated name destIPAddrIPV4

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description The parameter defines the destination IP address of the static route which is redis-tributed and the address is specified in the conventional dot notation (#.#.#.#).

The corresponding MML command group: ZQKU. If ALL is given, all valid static routes are redistributed.

Range 7...15

Step -

Units characters



Default value -


Table 188 destIPAddrIPV4 (DestIPAddrIPV4)

194 DN70257257



ISPRT Parameters

22.10 gatewayIPV4 (GatewayIPV4)

Related functions -




Related options -



References -

Table 188 destIPAddrIPV4 (DestIPAddrIPV4) (Cont.)

Parameter name GatewayIPV4

Abbreviated name gatewayIPV4

3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description The parameter defines the gateway IP address of the static route which is redistrib-uted and the address is specified in the conventional dot notation (#.#.#.#).

Range 7...15

Step -

Units characters



Default value -


Related functions -




Related options -


Table 189 gatewayIPV4 (GatewayIPV4)

DN70257257 195





References -

Table 189 gatewayIPV4 (GatewayIPV4) (Cont.)



3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1



Range 1... 16777215

Step 1

Units -



Default value 1


Related functions -




Related options -



References -


196 DN70257257



ISPRT Parameters




3GPP name -

Managed Object -

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the netmask of the static route which is redistributed.

The corresponding MML command group: ZQKU.

Range 1... 32

Step 1

Units -



Default value -


Related functions -




Related options -



References -


DN70257257 197

IP Configuration Plan Interface Parameters ITRKGRP Parameters


23 ITRKGRP Parameters

23.1 trkGrpBoolVal (Network Status Tracker Group Operation Bool Value)

Parameter name Network Status Tracker Group Operation Bool Value

Abbreviated name trkGrpBoolVal

3GPP name -

Managed Object ITRKGRP

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the bool value of the network tracker group.

The input value is only valid when creating the non-default tracker group(trk-GrpId!=0) with trkGrpOperation=BOOL. It is ignored when the trkGrpOperation is WEIGHT.

When creating the default tracker group(trkGrpId=0), this parameter is the fixed value 0(OR).

The corresponding commands: ZQJC.

Range OR (0), AND (1)

Step -

Units -


gui ==> internal

OR ==> 0

AND ==> 1

Default value OR (0)


Related functions -




Related options -



References -

Table 192 trkGrpBoolVal (Network Status Tracker Group Operation Bool Value)

198 DN70257257



ITRKGRP Parameters

23.2 trkGrpId (Network Status Tracker Group ID)

Parameter name Network Status Tracker Group ID

Abbreviated name trkGrpId

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the network tracker group identification.

Group ID 0 (default) is unique on the single EIPU unit. However, other group IDs (1~127) are unique on the whole RNC.

When creating the tracker group with trkGrpId=0, the following parameters are the fixed values. All the input values are ignored.

trkGrpType: 0(Faulty Switchover)

trkGrpOperation: 0(BOOL)

trkGrpBoolVal: 0(OR)

When creating the group with trkGrpId 0, two ITRKOBJs will be created without the trkObjWeight values:

ITRKOBJ-IFGE0

ITRKOBJ-IFGE1

When deleting an ITRKGRP, all the ITRKOBJs attached will be deleted.

The identifier is part of the distinguished name and it is formed in the following way: NE-x/IPNO-unitType-unitIndex/ITRKGRP-trkGrpId. For example: RNC-02/IPNO-NPGEP-0/ITRKGRP-123.

The corresponding commands: ZQJC, ZQJM

Range 0... 127

Step 1

Units -



Default value -


Related functions -




Related options -

Table 193 trkGrpId (Network Status Tracker Group ID)

DN70257257 199



23.3 trkGrpOperation (Network Status Tracker Group Opera-tion)



References -

Table 193 trkGrpId (Network Status Tracker Group ID) (Cont.)

Parameter name Network Status Tracker Group Operation

Abbreviated name trkGrpOperation

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the tracker operation of the network tracker group.

The input value is only valid when creating the non-default tracker group(trk-GrpId!=0).

When creating the default tracker group(trkGrpId=0), this parameter is the fixed value 0(BOOL).


Range BOOL (0), WEIGHT (1)

Step -

Units -


gui ==> internal

BOOL ==> 0

WEIGHT ==> 1

Default value BOOL (0)


Related functions -




Related options -


Table 194 trkGrpOperation (Network Status Tracker Group Operation)

200 DN70257257



ITRKGRP Parameters

23.4 trkGrpWeightVal (Network Status Tracker Group Opera-tion Weight Value)


References -

Table 194 trkGrpOperation (Network Status Tracker Group Operation) (Cont.)

Parameter name Network Status Tracker Group Operation Weight Value

Abbreviated name trkGrpWeightVal

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the weight value of the network tracker group.

The input value is only valid when creating the non-default tracker group(trk-GrpId!=0) with trkGrpOperation=WEIGHT. It is ignored when the trkGrpOperation is BOOL.

When creating the default tracker group(trkGrpId=0), this parameter is ignored.


Range 1... 999

Step 1

Units -



Default value 100


Related functions -




Related options -



References -

Table 195 trkGrpWeightVal (Network Status Tracker Group Operation Weight Value)

DN70257257 201



23.5 trkType (Network Status Tracker Group Type)

Parameter name Network Status Tracker Group Type

Abbreviated name trkType

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the tracker type of the network tracker group.

The input value is only valid when creating the non-default tracker group(trk-GrpId!=0).

When creating the default tracker group(trkGrpId=0), this parameter is the fixed value 0(Faulty Switchover).


Range Faulty Switchover (0)

Step -

Units -


gui ==> internal

Faulty Switchover ==> 0

Default value Faulty Switchover (0)


Related functions -




Related options -



References -

Table 196 trkType (Network Status Tracker Group Type)

202 DN70257257



ITRKOBJ Parameters

24 ITRKOBJ Parameters

24.1 trkObjName (Network Status Tracker Object Name)

Parameter name Network Status Tracker Object Name

Abbreviated name trkObjName

3GPP name -

Managed Object ITRKOBJ

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the name of the network status tracker object.

The name must be one of the following names: "IFGE0", "IFGE1", "IFFE0", "IFFE1".

The ITRKOBJ cannot be added/deleted to/from the default ITRKGRP (trkGrpId=0). The ITRKOBJs in the default ITRKGRP are added/deleted automatically when cre-ating/deleting the default ITRKGRP.

The identifier is part of the distinguished name and it is formed in the following way: NE-x/IPNO-unitType-unitIndex/ITRKGRP-trkGrpId/ITRKOBJ-xxx. For example: RNC-02/IPNO-NPGEP-0/ITRKGRP-123/ITRKOBJ-IFGE0.

The corresponding commands: ZQJM.

Range 3...8

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 197 trkObjName (Network Status Tracker Object Name)

DN70257257 203

IP Configuration Plan Interface Parameters ITRKOBJ Parameters


24.2 trkObjWeight (Network Status Tracker Object Weight)

Parameter name Network Status Tracker Object Weight

Abbreviated name trkObjWeight

3GPP name -

Managed Object ITRKOBJ

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the weight of the network status tracker object.

The input value is only valid when creating the ITRKOBJ in the non-default tracker group(trkGrpId!=0) with trkGrpOperation=WEIGHT. It is ignored when creating the ITRKOBJ in the tracker group with trkGrpOperation=BOOL.

The corresponding commands: ZQJM

Range 1... 999

Step 1

Units -



Default value 100


Related functions -




Related options -



References -

Table 198 trkObjWeight (Network Status Tracker Object Weight)

204 DN70257257



IUBSNT Parameters

25 IUBSNT Parameters

25.1 IPV4MaskLength (IPV4 mask length)

25.2 IPV4SubnetAddress (IPV4 subnet address)

Parameter name IPV4 mask length

Abbreviated name IPV4MaskLength

3GPP name -

Managed Object IUBSNT

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the local subnet mask length.

The corresponding MML command: ZQMN,"local subnet mask length".

Range 4... 26

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 199 IPV4MaskLength (IPV4 mask length)

Parameter name IPV4 subnet address

Abbreviated name IPV4SubnetAddress

3GPP name -

Table 200 IPV4SubnetAddress (IPV4 subnet address)

DN70257257 205

IP Configuration Plan Interface Parameters IUBSNT Parameters


25.3 assocMaxRetrans (Association max retrans)


Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the local subnet IPv4 address.

The address is specified in the conventional dot notation (#.#.#.#). The correspond-ing MML command: ZQMN,"local subnet ipv4 address".

Range 7...15

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 200 IPV4SubnetAddress (IPV4 subnet address) (Cont.)

Parameter name Association max retrans

Abbreviated name assocMaxRetrans

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Table 201 assocMaxRetrans (Association max retrans)

206 DN70257257



IUBSNT Parameters

25.4 hbInterval (HB interval)

Description This parameter defines the association Max.Retrans (Maximum number of unac-knowledged transmissions (including heartbeats) per association).

The corresponding MML command: ZQMP.

Range 1... 15

Step 1

Units -



Default value 5


Related functions -




Related options -



References -

Table 201 assocMaxRetrans (Association max retrans) (Cont.)

Parameter name HB interval

Abbreviated name hbInterval

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Description This parameter defines HB.interval in milliseconds.


Range 100... 300000

Step 1

Units milliseconds

Table 202 hbInterval (HB interval)

DN70257257 207



25.5 iubsntId (Iubsnt Identifier)



Default value 1000


Related functions -




Related options -



References -

Table 202 hbInterval (HB interval) (Cont.)

Parameter name Iubsnt Identifier

Abbreviated name iubsntId

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Description Identifies the local subnet configuration in the system. The identifier is part of the distinguished name and is formed in the following way: NE-x/IUBSNT-x. For example: RNC-1/IUBSNT-1. The corresponding MML command: ZQMN.

Range 1... 1

Step 1

Units -



Default value -


Related functions -


Table 203 iubsntId (Iubsnt Identifier)

208 DN70257257



IUBSNT Parameters

25.6 maxInitRetrans (MaxInitRetrans)



Related options -



References -

Table 203 iubsntId (Iubsnt Identifier) (Cont.)

Parameter name MaxInitRetrans

Abbreviated name maxInitRetrans

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Description This parameter defines Max.Init.Retransmits.

Range 1... 254

Step 1

Units -



Default value 8


Related functions -




Related options -



References -

Table 204 maxInitRetrans (MaxInitRetrans)

DN70257257 209



25.7 pathMaxRetrans (PathMaxRetrans)

25.8 rtoInitial (RTO Initial)

Parameter name PathMaxRetrans

Abbreviated name pathMaxRetrans

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Description This parameter defines Path.Max.Retrans (Maximum number of unacknowledged transmissions (including heartbeats) per path).


Range 1... 15

Step 1

Units -



Default value 5


Related functions -




Related options -



References -

Table 205 pathMaxRetrans (PathMaxRetrans)

Parameter name RTO Initial

Abbreviated name rtoInitial

3GPP name -


Table 206 rtoInitial (RTO Initial)

210 DN70257257



IUBSNT Parameters

25.9 rtoMax (RTO Max)

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines RTO.initial (Initial retransmission time-out in milliseconds).

The corresponding MML command group: ZQMP.

Range 10... 60000

Step 1

Units milliseconds



Default value 1000


Related functions -




Related options -



References -

Table 206 rtoInitial (RTO Initial) (Cont.)

Parameter name RTO Max

Abbreviated name rtoMax

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Description This parameter defines RTO.Max (Maximum value of retransmission time-out in milliseconds).


Table 207 rtoMax (RTO Max)

DN70257257 211



25.10 rtoMin (RTO Min)

Range 10... 120000

Step 1

Units milliseconds



Default value 2000


Related functions -




Related options -



References -

Table 207 rtoMax (RTO Max) (Cont.)

Parameter name RTO Min

Abbreviated name rtoMin

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Description This parameter defines RTO.Min (Minimum value of retransmission time-out in mil-liseconds).

The corresponding MML command group: ZQMP.

Range 10... 20000

Step 1

Units milliseconds



Default value 750

Table 208 rtoMin (RTO Min)

212 DN70257257



IUBSNT Parameters

25.11 sackPeriod (sackPeriod)


Related functions -




Related options -



References -

Table 208 rtoMin (RTO Min) (Cont.)

Parameter name sackPeriod

Abbreviated name sackPeriod

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the sack period in milliseconds.

The corresponding MML command group: ZQMN, "sack period".

Range 0... 500

Step 1

Units milliseconds



Default value 200


Related functions -




Related options -


Table 209 sackPeriod (sackPeriod)

DN70257257 213



25.12 validCookieLife (Valid Cookie Life)


References -

Table 209 sackPeriod (sackPeriod) (Cont.)

Parameter name Valid Cookie Life

Abbreviated name validCookieLife

3GPP name -


Parameter group -

Classification -

Multiplicity 1

Description This parameter defines Valid.Cookie.Life.

Range 5000... 120000

Step 1

Units milliseconds



Default value 60000


Related functions -




Related options -



References -

Table 210 validCookieLife (Valid Cookie Life)

214 DN70257257



IVIF Parameters

26 IVIF Parameters

26.1 parentInterface (Vlan physical Interface)

26.2 vid (Vlan id)

Parameter name Vlan physical Interface

Abbreviated name parentInterface

3GPP name -

Managed Object IVIF

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the physical interface to which the VLAN interface is attached to.

The corresponding MML command group: ZQRM, "vlan physical interface".

Range 3...8

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 211 parentInterface (Vlan physical Interface)

Parameter name Vlan id

Abbreviated name vid

Table 212 vid (Vlan id)

DN70257257 215

IP Configuration Plan Interface Parameters IVIF Parameters


26.3 vlanIfId (Vlan Interface Identifier)

3GPP name -

Managed Object IVIF

Parameter group -

Classification -

Multiplicity 1

Description This parameter defines the VLAN id of the VLAN interface.

The corresponding MML command group: ZQRM, "vlan identifier".

Range 2... 4094

Step 1

Units -



Default value -


Related functions -




Related options -



References -

Table 212 vid (Vlan id) (Cont.)

Parameter name Vlan Interface Identifier

Abbreviated name vlanIfId

3GPP name -

Managed Object IVIF

Parameter group -

Classification -

Multiplicity 1

Table 213 vlanIfId (Vlan Interface Identifier)

216 DN70257257



IVIF Parameters

Description This parameter identifies the VLAN interface within the IP node entity in the system. The identifier is part of the distinguished name and it is formed in the following way: NE-x/IPNO-unitType-unitIndex/IVIF-ifName. For example: RNC-1/IPNO-NPGEP-0/IVIF-VL1.

The VLAN interface name is VLx, where x is a number and the range is from 0 to 9999.

The corresponding MML command group: ZQRM, "vlan interface".

Range 3...8

Step -

Units characters



Default value -


Related functions -




Related options -



References -

Table 213 vlanIfId (Vlan Interface Identifier) (Cont.)

ip conf param

Documents