ip-10 quick startup guide configuration upload-download.pdf

FibeAir® IP-10

Quick Startup Guide

IP-10 Quick Startup Guide Doc Rev0.1 2

PROPRIETARY

Contents

1. DOCUMENT PURPOSE ............................................................................................................... 3

2. DOCUMENT SCOPE..................................................................................................................... 3

3. STARTUP CONFIGURATION STEPS ....................................................................................... 3

3.1. LAUNCHING WEB-MANAGEMENT ............................................................................................ 4 3.2 SAVING UNIT INFORMATION………………………………………………………………….9


PROPRIETARY

1. Document Purpose

The purpose of this document is to describe the basic configuration steps of IP-10 radio link.

Refer to the IP-10 installation and management user guides for full configuration options.

2. Document Scope

This document describes the recommended initial steps in order to connect and manage IP-10 radio link. It includes the configuration steps of the following main sections:

Connecting to IDU using default factory setup

Launching the web management

Basic parameters configuration

3. Startup Configuration Steps

Basic configuration includes the following basic steps:

1. Complete physical HW installation of IDU, IF coax cable, RFU and antenna as per installation instructions.

2. Connect PC to IDU and launch web management.

3. Configure radio link parameters.

4. Complete link commissioning.


PROPRIETARY

3.1. Launching Web-Management 1.4.1 1.4.2 IDU factory Default Configuration

IP Address: 192.168.1.1, IP Mask 255.255.255.0.

Active management port: port #7 (far right RJ45 port), out-of band management.

Protection: Disabled. 1+0 configuration

1.4.3 Connecting to IDU

1. Verify no Ethernet traffic (cables or fibers) connected.

2. Power up IDU.

3. Connect PC to IDU management port (port #7, far right RJ45 port).

4. PC configuration: IP Address: 192.168.1.240, IP Mask 255.255.255.0, no default gateway.

5. Verify connectivity to IDU (ping 192.168.1.1). If no connectivity, verify IDU IP management configuration using Command Line Interface (refer to Appendix).

1.4.4 Launching Web-Management

1. Open Internet Explorer.

2. Type IDU's IP address (192.168.1.1) on address field. IP-10 login screen will be displayed.

3. User: admin. Password: admin.


PROPRIETARY

Customers may use Windows FTP-Server or any other FTP-Server freeware available.

1.4.5 Installing FTP-Server Software

You may install and use any FTP-Server software for SW download. Ceragon recommends using FileZilla_Server-0_9_26 software that can be downloaded from the web (freeware) or from Ceragon's FTP site.

1. Download zipped FileZilla_Server-0_9_26.zip from the internet or Ceragon's FTP site and store it on the PC (for example, C:\IP-10).

2. Extract the file and run the installation setup. Follow installation process until

finished (do not change any of the installation default settings).Initial Configuration of FTP-Server Software

After installing the FileZilla, it has to be configured to allow the SW download using FTP.

Stopping Windows FTP services

In order to use FileZilla, Windows default FTP services have to be stopped.

1. Go to Control Panel > Administrative Tools Internet Information Services, if the Internal Information Services don’t appear its means that the Windows FTP wasn’t install and you may have to proceed without doing so.

2. Use Right-Click to stop the Default FTP Site under FTP Sites.

Configuration of the FTP-Server software

User and files path have to be defined on the FTP-Server.

1. Launch the FileZilla Server Interface (go to Files Programs FileZilla Server FileZilla Server Interface).


PROPRIETARY

2. Click OK on the Connect to Server window. The FileZilla Server window will be displayed.

3. Select Edit Users Shared Folders. The Users window will be displayed.

4. Select Add on the Users section and enter anonymous in the Add user Account window.

5. Select Add on the Shared Folders section and select local drive C:\ in the Browse for Folder.


PROPRIETARY

6. Select (check) Read, Write and Delete in the Files section.

7. Verify your configuration is identical to the displayed in the following window:

8. Select OK and close the FileZilla server.

Launching of the FTP-Server software

User and files path have to be defined on the FTP-Server.

2. Launch the FileZilla Server Interface (go to Files Programs FileZilla Server FileZilla Server Interface).

3. Click OK on the Connect to Server window. The FileZilla Server window will be displayed.


PROPRIETARY

4. Verify server is running (yellow lightning Bolt on top-left corner highlighted and status is Logged On.


PROPRIETARY

Save Unit Information

3.4.1 Open the IDU and go to: /Diagnostic & management/Configuration management.

3.4.2 Go to Configuration management Parameters: and fill in as follows:

Host IP - your computer IP Host Path - // User name – anonymous User Password - enter your laptop windows user name and apply.

3.4.3 Lunch FileZilla FTP Server and make sure it’s running (yellow Bolt)

3.4.4 Under “Unit Information” click on the “Create Archive” tab and wait till the browser will disconnect you from the IDU.

3.4.5 Re-Connect to IDU and go again to: /Diagnostic & management/Configuration management.

3.4.6 Under “Unit Information” click on the “Upload Archive” tab and watch the FilleZilla FTP server screen and verify that all the files were sent to the path you have specified on the /FilleZilla/Edit/Users/Shared


PROPRIETARY

Folder. 3.4.7 Go to /My Computer/C and look for a file name of xxx xxx.tar.tz and

extract it to where ever you choose.

3.4.8 After extracting it go to /Var/Lib/Aidc and the file name is “dmae_tech.log”

DOWNLOADING: This option allows you to download uploaded files

from a host (such as a PC) to the target (IDU). Downloading a configuration

involves three steps:

3.4.9 Download archive - This command copies the configuration file from the host to the target.

3.4.10 Install archive - This command installs the configuration file, which will be operational only after a hardware reset.

3.4.11 HW reset - When the system is up and running, the new downloaded configuration will be valid. In the Download Configuration Status & Commands area:

Config download status - indicates indicates whether or not the configuration file was

downloaded successfully from host to target.

Config install status - indicates whether or not the configuration file was installed

successfully on the target.

Click Download Archive to download the archive file from the host to the target.

Click Install Archive to install the requested archive file on the target.

Default Configuration area:

Click Activate to set the unit to the default configuration. To apply changes you made,

click Apply. To update the information, click Refresh.

ip-10 quick startup guide configuration upload-download.pdf

Documents