iogp report 530 electrotechnical standards relevent for the oil and gas industry
DESCRIPTION
IOGP technical standard 530TRANSCRIPT
-
Electrotechnical standards relevant for the oil and gas industry / 1
Electrotechnical standards relevant for the oil and gas industry
REPORT 530
MARCH 2015
-
Electrotechnical standards relevant for the oil and gas industry / 2
Contents
Contents 2
Acknowledgement 3
Disclaimer 3
Copyright notice 3
Introduction 4
Purpose of report 5
Abbreviations 6
IEC standards specific to the oil and gas industry 8
IEC standards relevant for the oil and gas industry 9
API Standards 50
IEEE (PCIC) Standards 51
NEMA National Electrical Manufacturers Association 58
NFPA codes & standards 61
EEMUA publications 62
UL standards 63
Classification societys standards 66
Energy Institute documents 67
EN standards 68
GSO Electrotechnical standards 71
Other relevant codes, documents & standards 72
-
Electrotechnical standards relevant for the oil and gas industry / 3
Acknowledgement
This report was developed by the IOGP Electrical Standards Subcommittee.
Disclaimer Whilst every effort has been made to ensure the accuracy of the information contained in this publication, neither IOGP nor any of its Members past present or future warrants its accuracy or will, regardless of its or their negligence, assume liability for any foreseeable or unforeseeable use made thereof, which liability is hereby excluded. Consequently, such use is at the recipient's own risk on the basis that any use by the recipient constitutes agreement to the terms of this disclaimer. The recipient is obliged to inform any subsequent recipient of such terms.
Copyright notice The contents of these pages are International Association of Oil & Gas Producers. Permission is given to reproduce this report in whole or in part provided (i) that the copyright of IOGP and (ii) the source are acknowledged. All other rights are reserved. Any other use requires the prior written permission of IOGP.
These Terms and Conditions shall be governed by and construed in accordance with the laws of England and Wales. Disputes arising here from shall be exclusively subject to the jurisdiction of the courts of England and Wales.
-
Electrotechnical standards relevant for the oil and gas industry / 4
Introduction
The International Association of Oil & Gas Producers (IOGP) organized a workshop 1011 May 2012, in London, within the scope of electrical standards and practices for the oil and gas industry for electrical technology specialists of IOGP Members and invited guests.
The objectives of the workshop were to:
arrange for global networking amongst the specialists
review and discuss the available standards for electrical installations, ongoing standards work and existing company specifications related to this discipline
evaluate the needs for improvements of available industry, national or regional standards or company specifications and harmonization with international standards in this area
evaluate the need for new electrical standards work in the oil and gas industry
share company and/or personal experience regarding electrical installations, standards and practices.
Within the goal for the workshop was also to identify and prioritize improvements to available standards or the need for new international (IEC) standards in the electrical area for the benefit of the global oil and gas industry.
A draft of this report was initially prepared as a basis for this workshop and, following input from this workshop, IOGP has established the Electrical Standards Subcommittee with the same objectives as for the workshop. The Subcommittee has subsequently agreed to complete this document as an IOGP reference report including input from its Members and a benchmarking exercise in 2013.
This report should be seen in conjunction with the following IOGP reports:
Report 362, Catalogue of international standards used in the petroleum and natural gas industries (February 2012) where a number of IEC standards are identified
Report 381, Position paper on the development and use of international standards (March 2010) outlining the importance of IEC standards
Report 426, Regulators use of standards (March 2010) including some references to IEC standards
Report 450, Benchmarking on the use of internal technical specifications and external standards by some oil & gas companies (February 2011).
-
Electrotechnical standards relevant for the oil and gas industry / 5
Purpose of report
The purpose of this report is to provide a list of some of the available and relevant international, regional, national and industry electrotechnical standards for the oil and gas industries as seen by the participants of the IOGP Electrical Standards Subcommittee. This report is not exhaustive in any way and there may well be other relevant electrotechnical standards for the oil and gas industries.
-
Electrotechnical standards relevant for the oil and gas industry / 6
Abbreviations
API American Petroleum Institute
ABS American Bureau of Shipping
BV Bureau Veritas
CRE Committee of Refining Equipment (under API)
CSA Canadian Standards Association
C-NLOPB Canada-Newfoundland and Labrador Offshore Petroleum Board
DNV Det Norske Veritas
DNV- GL Det Norske Veritas GL
EEMUA Engineered Equipment Materials User Association
EI Energy Institute (formerly Institute of Petroleum)
GSO Standardization Organization for the Cooperation Council for the Arab States of the Gulf
IALA International Association of Marine Aids to Navigation and Lighthouse Authorities
IAPH International Association of Ports and Harbors
IACS International Association of Classification Societies
ICAO International Civil Aviation Organization
IAS Industry Applications Society (under IEEE)
ICS International Chamber of Shipping
IEC International Electrotechnical Commission
IEE Now IET
IEEE Institute of Electrical and Electronics Engineers
IET Institution of Engineering and Technology
IMCA International Maritime Contractors Association
IMO International Maritime Organization
ISO International Organization for Standardization
-
Electrotechnical standards relevant for the oil and gas industry / 7
ISGOTT International Safety Guide for Oil Tankers and Terminals
ISPS International Ships and Port Facilities Security Code
LR Lloyds Register
MARPOL International Convention for the Prevention of Pollution From Ships (IMO)
MEPC Marine Environment Protection Committee (in IMO)
NEC National Electrical Code
NEK Norwegian Electrotechnical Committee
NEMA National Electrical Manufacturers Association
NFPA National Fire Protection Association
OCIMF Oil Companies International Marine Forum
IOGP International Association of Oil & Gas Producers
PCIC Petroleum and Chemical Industry Committee (under IEEE IAS)
SCAPC Standards and Conformity Assessment Policy Committee (under NEMA)
SCC Standards Council of Canada
SDO Standards Developing Organization
SOEE Subcommittee on Electrical Equipment
SOLAS International Convention of Safety Of Life At Sea (IMO)
TC Technical Committee
UL Underwriters Laboratories
USCG U.S. Coast Guard
-
Electrotechnical standards relevant for the oil and gas industry / 8
IEC standards specific to the oil and gas industry
IEC 61892-1, Mobile and fixed offshore units Electrical installations Part 1: General requirements and conditions
IEC 61892-2, Mobile and fixed offshore units Electrical installations Part 2: System design
IEC 61892-3, Mobile and fixed offshore units Electrical installations Part 3: Equipment
IEC 61892-4, Mobile and fixed offshore units Electrical installations Part 4: Cables
IEC 61892-5, Mobile and fixed offshore units Electrical installations Part 5: Mobile units
IEC 61892-6, Mobile and fixed offshore units Electrical installations Part 6: Installation
IEC 61892-7, Mobile and fixed offshore units Electrical installations Part 7: Hazardous areas
-
Electrotechnical standards relevant for the oil and gas industry / 9
IEC standards relevant for the oil and gas industry
IEC 60034, Rotating electrical machines
IEC 60034-1, Rotating electrical machines Part 1: Rating and performance
IEC 60034-11, Rotating electrical machines Part 11: Thermal protection
IEC 60034-12, Rotating electrical machines Part 12: Starting performance of single-speed three phase cage induction motors
IEC 60034-14, Rotating electrical machines Part 14: Mechanical vibration of certain machines with shaft heights 56 mm and higher Measurement, evaluation and limits of vibration severity
IEC 60034-15, Rotating electrical machines Part 15: Impulse voltage withstand levels of form-wound stator coils for rotating a.c. machines
IEC 60034-16, Excitation systems for synchronous machines
IEC 60034-16-1, Rotating electrical machines Part 16: Excitation systems for synchronous machines - Chapter 1: Definitions
IEC 60034-18, Rotating electrical machines Part 18: Functional evaluation of insulation systems
IEC 60034-18-1, Rotating electrical machines Part 18-1: Functional evaluation of insulation systems General guidelines
IEC 60034-18-21, Rotating electrical machines Part 18: Functional evaluation of insulation systems Section 21: Test procedures for wire-wound windings - Thermal evaluation and classification
IEC 60034-18-22, Rotating electrical machines Part 18-22: Functional evaluation of insulation systems Test procedures for wire-wound windings - Classification of changes and insulation component substitutions
IEC 60034-18-31, Rotating electrical machines Part 18-31: Functional evaluation of insulation systems Test procedures for form-wound windings Thermal evaluation and classification of insulation systems used in rotating machines
IEC 60034-18-32, Rotating electrical machines Part 18-32: Functional evaluation of insulation systems Test procedures for form-wound windings - Evaluation by electrical endurance
IEC 60034-18-33, Rotating electrical machines Part 18-33: Functional evaluation of insulation systems Test procedures for form-wound windings Multifactor evaluation by endurance under simultaneous thermal and electrical stresses
-
Electrotechnical standards relevant for the oil and gas industry / 10
IEC 60034-18-34, Rotating electrical machines Part 18-34: Functional evaluation of insulation systems Test procedures for form-wound windings Evaluation of thermomechanical endurance of insulation systems
IEC 60034-18-41, Rotating electrical machines Part 18-41: Qualification and type tests for Type I electrical insulation systems used in rotating electrical machines fed from voltage converters
IEC 60034-18-42, Rotating electrical machines Part 18-42: Qualification and acceptance tests for partial discharge resistant electrical insulation systems (Type II) used in rotating electrical machines fed from voltage converters
IEC 60034-19, Rotating electrical machines Part 19: Specific test methods for d.c. machines on conventional and rectifier-fed supplies
IEC 60034-2, Rotating electrical machines Part 2-1:Standard methods for determining losses and efficiency from tests (excluding machines for traction vehicles)
IEC 60034-2-1, Rotating electrical machines Part 2-1: Standard methods for determining losses and efficiency from tests (excluding machines for traction vehicles).
IEC 60034-22, Rotating electrical machines Part 22: AC generators for reciprocating internal combustion (RIC) engine driven generating sets
IEC 60034-2-2 , Rotating electrical machines Part 2-2: Specific methods for determining separate losses of large machines from tests - Supplement to IEC 60034-2-1
IEC 60034-2-3 , Rotating electrical machines Part 2-3: Specific test methods for determining losses and efficiency of converter-fed AC motors
IEC 60034-25, Rotating electrical machines Part 25: Guidance for the design and performance of a.c. motors specifically designed for converter supply
IEC 60034-26, Rotating electrical machines Part 26: Effects of unbalanced voltages on the performance of three-phase cage induction motors
IEC 60034-27, Rotating electrical machines Part 27: Off-line partial discharge measurements on the stator winding insulation of rotating electrical machines
IEC 60034-28, Rotating electrical machines Part 28: Test methods for determining quantities of equivalent circuit diagrams for three-phase low-voltage cage induction motors
IEC 60034-29, Rotating electrical machines Part 29: Equivalent loading and superposition techniques - Indirect testing to determine temperature rise
IEC 60034-2A, Rotating electrical machines Part 2: Methods for determining losses and efficiency of rotating electrical machinery from tests (excluding machines for traction vehicles) Measurement of losses by the calorimetric method
IEC 60034-3, Rotating electrical machines Part 3: Specific requirements for synchronous generators driven by steam turbines or combustion gas turbines
-
Electrotechnical standards relevant for the oil and gas industry / 11
IEC 60034-30, Rotating electrical machines Part 30: Efficiency classes of single-speed, three-phase, cage-induction motors (IE-code)
IEC 60034-31, Rotating electrical machines Part 31: Guide for the selection and application of energy-efficient motors including variable-speed applications
IEC 60034-4, Rotating electrical machines Part 4: Methods for determining synchronous machine quantities from tests
IEC 60034-5, Rotating electrical machines Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
IEC 60034-6, Rotating electrical machines Part 6: Methods of cooling (IC Code)
IEC 60034-7, Rotating electrical machines Part 7: Terminal markings and direction of rotation.
IEC 60034-8, Rotating electrical machines Part 8: Terminal markings and direction of rotation
IEC 60034-9, Rotating electrical machines Part 9: Noise limits
IEC 60038, IEC standard voltages
IEC 60044, Instrument transformers
IEC 60044-1, Instrument transformers Part 1: Current transformers
IEC 60044-2, Instrument transformers Part 2 : Inductive voltage transformers
IEC 60044-3, Instrument transformers Part 3: Combined transformers
IEC 60044-5, Instrument transformers Part 5: Capacitor voltage transformers
IEC 60044-6, Instrument transformers Part 6: Requirements for protective current transformers for transient performance
IEC 60044-7, Instrument transformers Part 7: Electronic voltage transformers
IEC 60044-8, Instrument transformers Part 8: Electronic current transformers
IEC 60050, International Electrotechnical vocabulary
IEC 60050-161, International Electrotechnical Vocabulary Chapter 161: Electromagnetic compatibility
IEC 60050-191, International Electrotechnical Vocabulary Chapter 191: Dependability and quality of service
IEC 60050-300, International Electrotechnical Vocabulary Electrical and electronic -measurements and measuring instruments
IEC 60050-411, International Electrotechnical Vocabulary Part 411: Rotating machinery
-
Electrotechnical standards relevant for the oil and gas industry / 12
IEC 60050-426, International Electrotechnical Vocabulary Chapter 426: Equipment for explosive atmospheres
IEC 60050-441, International Electrotechnical Vocabulary Chapter 441: Switchgear, controlgear and fuses
IEC 60050-446, International Electrotechnical Vocabulary Chapter 446: Electrical relays
IEC 60050-617, International Electrotechnical Vocabulary Part 617: Organization/Market of electricity - Edition 1.0
IEC 60050-702, International Electrotechnical Vocabulary Chapter 702: Oscillations, signals and related devices
IEC 60050-826, International Electrotechnical Vocabulary Part 826: Electrical installations
IEC 60050-845, International Electrotechnical Vocabulary Chapter 845: Lighting
IEC 60051, Direct acting indicating analogue electrical measuring instruments and their accessories All Parts
IEC 60051-1, Direct acting indicating analogue electrical measuring instruments and their accessories Part 1: Definitions and general requirements common to all parts
IEC 60051-2, Direct acting indicating analogue electrical measuring instruments and their accessories Part 2: Special requirements for ammeters and voltmeters
IEC 60051-3, Direct acting indicating analogue electrical measuring instruments and their accessories Part 3: Special requirements for wattmeters and varmeters
IEC 60051-4, Direct acting indicating analogue electrical measuring instruments and their accessories Part 4: Special requirements for frequency meters
IEC 60051-5, Direct acting indicating analogue electrical measuring instruments and their accessories Part 5: Special requirements for phase meters, power factor meters and synchroscopes
IEC 60051-6, Direct acting indicating analogue electrical measuring instruments and their accessories Part 6: Special requirements for ohmmeters (impedance meters) and conductance meters
IEC 60051-7, Direct acting indicating analogue electrical measuring instruments and their accessories Part 7: Special requirements for multi-function instruments
IEC 60051-8, Direct acting indicating analogue electrical measuring instruments and their accessories Part 8: Special requirements for accessories
IEC 60051-9, Direct acting indicating analogue electrical measuring instruments and their accessories Part 9: Recommended test methods
IEC 60059, IEC standard current ratings
-
Electrotechnical standards relevant for the oil and gas industry / 13
IEC 60060, High-voltage test techniques.
IEC 60060-1, High-voltage test techniques Part 1: General definitions and test requirements
IEC 60060-2, High voltage test techniques Part 2: Measuring systems
IEC 60060-3, High-voltage test techniques Part 3: Definitions and requirements for on-site testing
IEC 60061-1, Lamp caps and holders together with gauges for the control of interchangeability and safety Part 1: Lamp caps
IEC 60064, Tungsten filament lamps for domestic and similar general lighting purposes Performance requirements
IEC 60068, Environmental testing
IEC 60068-1, Environmental testing Part 1: General and guidance
IEC 60068-2, Environmental testing Part 2-6: Tests Test Fc: Vibration (sinusoidal)
IEC 60068-2-1, Environmental testing Part 2-1: Tests Test A: Cold
IEC 60068-2-14, Environmental testing Part 2-14: Tests Test N: Change of temperature
IEC 60068-2-2 , Environmental testing Part 2-2: Tests Test B: Dry heat
IEC 60068-2-27, Environmental testing Part 2-27: Tests Test Ea and guidance: Shock
IEC 60068-2-30, Environmental testing Part 2-30: Tests Test Db: Damp heat, cyclic (12 h + 12 h cycle)
IEC 60068-2-52, Environmental testing Part 2: Tests, Test Kb: Salt mist, cyclic (sodium chloride solution)
IEC 60068-2-6, Environmental testing Part 2-6: Tests Test Fc: Vibration (sinusoidal)
IEC 60068-2-75, Environmental testing Part 2: Tests Test Eh: Hammer tests
IEC 60068-2-78, Draft Document - Environmental testing Part 2-78: Tests Test Cab: Damp heat, steady state
IEC 60071, Insulation co-ordination
IEC 60071-1 Insulation co-ordination Part 1: Definitions, principles and rules
IEC 60071-2 Insulation co-ordination Part 2: Application guide
IEC 60071-4 Insulation co-ordination Part 4: Computational guide to insulation co-ordination and modelling of electrical networks
IEC 60071-5 Insulation co-ordination Part 5: Procedures for high-voltage direct current (HVDC) converter stations
-
Electrotechnical standards relevant for the oil and gas industry / 14
IEC 60072, Dimensions and output series for rotating electrical machines
IEC 60072-1, Dimensions and output series for rotating electrical machines Part 1: Frame numbers 56 to 400 and flange numbers 55 to 1080
IEC 60072-2, Dimensions and output series for rotating electrical machines Part 2: Frame numbers 355 to 1000 and flange numbers 1180 to 2360
IEC 60072-3, Dimensions and output series for rotating electrical machines Part 3: Small built-in motors - Flange numbers BF10 to BF50
IEC 60073, Basic and safety principles for man-machine interface, marking and identification Coding principles for indicators and actuators
IEC 60076, Power transformers (all parts)
IEC 60076-1, Power transformers Part 1: General
IEC 60076-10, Power transformers Part 10: Determination of sound levels
IEC 60076-10-1, Power transformers Part 10-1: Determination of sound levels Application guide
IEC 60076-11, Power transformers Part 11: Dry-type transformers
IEC 60076-12, Power transformers Part 12: Loading guide for dry-type transformers
IEC 60076-13, Power transformers Part 13: Self-protected liquid-filled transformers
IEC 60076-14, Power transformers Part 14: Design and application of liquid-immersed power transformers using high-temperature insulation materials
IEC 60076-15, Power transformers Part 15: Gas-filled power transformers
IEC 60076-16, Power transformers Part 16: Transformers for wind turbine applications
IEC 60076-17, Power transformers Part 17: Evaluation of electromagnetic fields around power transformers
IEC 60076-18, Power transformers Part 18: Measurement of frequency response
IEC 60076-2, Power transformers Part 2: Temperature rise for liquid-immersed transformers
IEC 60076-21, Power Transformers Part 21: Standard Requirements, Terminology, and Test Code for Step-Voltage Regulators
IEC 60076-3 ,Power transformers Part 3: Insulation levels, dielectric tests and external clearances in air
IEC 60076-3-1, Power Transformers External Clearances In Air
IEC 60076-4, Power transformers Part 4: Guide to the lightning impulse and switching impulse testing Power transformers and reactors
-
Electrotechnical standards relevant for the oil and gas industry / 15
IEC 60076-5, Power transformers Part 5: Ability to withstand short circuit
IEC 60076-6, Power transformers Part 6: Reactors
IEC 60076-7, Power transformers Part 7: Loading guide for oil-immersed power transformers
IEC 60076-8, Power transformers Part 8: Application guide
IEC 60079, Electrical apparatus for explosive gas atmospheres
IEC 60079-0, Explosive atmospheres Part 0: Equipment General requirements
IEC 60079-1, Electrical apparatus for explosive gas atmospheres Flameproof enclosures 'd'
IEC 60079-10, Electrical apparatus for explosive gas atmospheres Part 10: Classification of hazardous areas
IEC 60079-10-1, Explosive atmospheres Part 10-1: Classification of areas Explosive gas atmospheres
IEC 60079-10-2, Explosive atmospheres Part 10-2: Classification of areas Combustible dust atmospheres
IEC 60079-11, Explosive atmospheres Part 11: Equipment protection by intrinsic safety "i"
IEC 60079-13, Electrical apparatus for explosive gas atmosphere Part 13: Construction and use of rooms or buildings protected by pressurization
IEC 60079-14, Explosive atmospheres Part 14: Electrical installations design, selection and erection
IEC 60079-15, Explosive atmospheres Part 15: Equipment protection by type of protection "n"
IEC 60079-16, Electrical apparatus for explosive gas atmospheres Part 16: Artificial ventilation for the protection of analyser(s) houses
IEC 60079-17, Explosive atmospheres Part 17: Electrical installations inspection and maintenance
IEC 60079-18, Explosive atmospheres Part 18: Equipment protection by encapsulation m
IEC 60079-19, Explosive atmospheres Part 19: Equipment repair, overhaul and reclamation
IEC 60079-2, Explosive atmospheres Part 2: Equipment protection by pressurized enclosure p
IEC 60079-20, Explosive atmospheres Part 20: Material characteristics for gas and vapour classification
IEC 60079-20-1, Explosive atmospheres Part 20-1: Material characteristics for gas and vapour classification Test methods and data
IEC 60079-25, Electrical apparatus for explosive gas atmospheres Part 25: Intrinsically safe systems
-
Electrotechnical standards relevant for the oil and gas industry / 16
IEC 60079-26, Explosive atmospheres Part 26: Equipment with equipment protection level (EPL) Ga
IEC 60079-27, Explosive atmospheres Part 27: Fieldbus intrinsically safe concept (FISCO)
IEC 60079-28, Explosive atmospheres Part 28: Protection of equipment and transmission systems using optical radiation
IEC 60079-29, Explosive atmospheres Part 29: Gas detectors; Selection, installation, use and maintenance of detectors for flammable gases and oxygen
IEC 60079-29-1, Explosive atmospheres Part 29-1: Gas detectors Performance requirements of detectors for flammable gases
IEC 60079-29-2, Explosive atmospheres Part 29-2: Gas detectors Selection, installation, use and maintenance of detectors for flammable gases and oxygen
IEC 60079-29-3, Explosive atmospheres Part 29-3: Gas detectors- Requirements on the functional safety of fixed gas detection systems
IEC 60079-29-4, Explosive atmospheres Part 29-4: Gas detectors Performance requirements of open path detectors for flammable gases
IEC 60079-30-1, Explosive atmospheres Part 30-1: Electrical resistance trace heating General and testing requirements
IEC 60079-30-2, Explosive atmospheres Part 30-2: Electrical resistance trace heating Application guide for design, installation and maintenance
IEC 60079-31, Explosive atmospheres Part 31: Equipment dust ignition protection by enclosure "t"
IEC 60079-33, Explosive atmospheres Part 33: Equipment protection by special protection 's'
IEC 60079-35-1, Caplights for use in mines susceptible to firedamp Part 1: General requirements Construction and testing in relation to the risk of explosion
IEC 60079-35-2, Caplights for use in mines susceptible to firedamp Part 2: Performance and other safety-related matters
IEC 60079-5, Explosive atmospheres Part 5: Equipment protection by powder filling q
IEC 60079-6, Explosive atmospheres Part 6: Equipment protection by oil immersion o
IEC 60079-7, Explosive atmospheres Part 7: Equipment protection by increased safety e
IEC 60081, Double-capped fluorescent lamps Performance specifications
IEC 60083, Plugs and socket-outlets for domestic and similar general use standardized in member countries of IEC
IEC 60085, Electrical insulation Thermal evaluation and designation
-
Electrotechnical standards relevant for the oil and gas industry / 17
IEC 60092, Electrical installations in ships
IEC 60092-101, Electrical installations in ships Part 101: Definitions and general requirements
IEC 60092-201, Electrical installation in ships System design General
IEC 60092-302, Electrical installation in ships Low-voltage switchgear and controlgear assemblies
IEC 60092-350, Electrical installations in ships Part 350: General construction and test methods of power, control and instrumentation cables for shipboard and offshore applications
IEC 60092-352, Electrical installations in ships Part 352: Choice and installation of electrical cables
IEC 60092-353, Electrical installations in ships Part 353: Single and multicore non-radial field power cables with extruded solid insulation for rated voltages 1 kV and 3 kV
IEC 60092-354, Electrical installations in ships Part 354: Single and three-core power cables with extruded solid insulation for rated voltages 6 kV (Um = 7,2 kV); up to 30 kV (Um = 36 kV)
IEC 60092-360, Electrical installations in ships Part 360: Insulating and sheathing materials for shipboard and offshore units, power, control, instrumentation and telecommunication cables
IEC 60092-370, Electrical installations in ships Part 370: Guidance on the selection of cables for telecommunication and data transfer including radio-frequency cables
IEC 60092-376, Electrical installations in ships Part 376: Cables for control and instrumentation circuits 150/250 V (300 V)
IEC 60092-401, Electrical installations in ships Part 401: Installation and test of completed installation
IEC 60092-501 , Electrical installations in ships Part 501: Special features Electric propulsion plant
IEC 60092-502, Electrical installations in ships Part 502: Tankers, Special Features
IEC 60092-504, Electrical installations in ships Part 504: Special features Control and instrumentation
IEC 60092-509, Electrical installations in ships Part 509: Operation of electrical installations
IEC 60095-1, Lead acid starter batteries Part 1: General requirements and methods of test
IEC 60099, Lightening arresters
IEC 60099-1, Surge arresters Part 1: Non-linear resistor type gapped surge arresters for a.c. systems
IEC 60099-5, Surge arresters Part 5: Selection and application recommendations
-
Electrotechnical standards relevant for the oil and gas industry / 18
IEC 60112, Method for the determination of the proof and the comparative tracking indices of solid insulating materials
IEC 60120, Dimensions of ball & socket couplings of string insulator units
IEC 60137, Insulated bushings for alternating voltages above 1000 V
IEC 60146, Semiconductor convertors General requirements and line commutated convertors
IEC 60146-1-1, Semiconductor converters General requirements and line commutated converters Part 1-1: Specification of basic requirements
IEC 60146-1-2, Semiconductor converters - General requirements and line commutated converters Part 1-2: Application guide
IEC 60146-1-3, Semiconductor converters General requirements and line commutated converters Part 1-3: Transformers and reactors
IEC 60146-2, Semiconductor converters Part 2: Self-commutated semiconductor converters including direct d.c. converters
IEC 60152, Identification by hour numbers of the phase conductors of 3-phase electric systems
IEC 60155, Glow-starters for fluorescent lamps
IEC 60156, Insulating liquids Determination of the breakdown voltage at power frequency Test method
IEC 60169, Radio-frequency connectors
IEC 60183, Guide to the selection of high-voltage cables
IEC 60189-2, Low-frequency cables and wires with PVC insulation and PVC sheath Part 2: Cables in pairs, triples, quads and quintuples for inside installations
IEC 60191-6, Mechanical standardization of semiconductor devices Part 6: General rules for the preparation of outline drawings of surface mounted semiconductor device packages
IEC 60196, IEC standard frequencies
IEC 60204-1, Electrical equipment of industrial machines Part 1: General rules
IEC 60214, Tap-changers
IEC 60214-1, Tap-changers Part 1: Performance requirements and test methods
IEC 60214-2, Tap-changers Part 2: Application guide
IEC 60215, Safety requirements for radio transmitting equipment
IEC 60227, Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V (all parts)
-
Electrotechnical standards relevant for the oil and gas industry / 19
IEC 60228, Conductors of insulated cables
IEC 60229, Electric cables Tests on extruded oversheaths with a special protective function
IEC 60243-1, Electric strength of insulating materials Test methods Part 1: Tests at power frequencies
IEC 60245, Rubber insulated cables Rated voltages up to and including 450/750 V (all parts)
IEC 60247, Insulating liquids Measurement of relative permittivity, dielectric dissipation factor (tan d) and d.c. resistivity
IEC 60255, Electrical relays
IEC 60255-1, Measuring relays and protection equipment Part 1: Common requirements
IEC 60255-11, Measuring relays and protection equipment Part 11: Voltage dips, short interruptions, variations and ripple on auxiliary power supply port
IEC 60255-12, Electrical relays Part 12: Directional relays and power relays with two input energizing quantities
IEC 60255-121, Measuring relays and protection equipment Part 121: Functional requirements for distance protection
IEC 60255-127, Measuring relays and protection equipment Part 127: Functional requirements for over/under voltage protection
IEC 60255-13, Electrical relays Part 13: Biased (percentage) differential relays
IEC 60255-151, Measuring relays and protection equipment Part 151: Functional requirements for over/under current protection
IEC 60255-16, Electrical relays Part 16: Impedance measuring relays
IEC 60255-21-1, Electrical relays Part 21: Vibration, shock, bump and seismic tests on measuring relays and protection equipment - Section One: Vibration tests (sinusoidal)
IEC 60255-21-2, Electrical relays Part 21: Vibration, shock, bump and seismic tests on measuring relays and protection equipment Section Two: Shock and bump tests
IEC 60255-21-3, Electrical relays Part 21: Vibration, shock, bump and seismic tests on measuring relays and protection equipment Section 3: Seismic tests
IEC 60255-22-1, Measuring relays and protection equipment Part 22-1: Electrical disturbance tests 1 MHz burst immunity tests
IEC 60255-22-2, Measuring relays and protection equipment Part 22-2: Electrical disturbance tests Electrostatic discharge tests
IEC 60255-22-3, Measuring relays and protection equipment Part 22-3: Electrical disturbance tests Radiated electromagnetic field immunity
-
Electrotechnical standards relevant for the oil and gas industry / 20
IEC 60255-22-4, Measuring relays and protection equipment Part 22-4: Electrical disturbance tests - Electrical fast transient/burst immunity test
IEC 60255-22-5, Measuring relays and protection equipment Part 22-5: Electrical disturbance tests - Surge immunity test
IEC 60255-22-6, Electrical relays Part 22-6: Electrical disturbance tests for measuring relays and protection equipment Immunity to conducted disturbances induced by radio frequency fields
IEC 60255-22-7, Electrical relays Part 22-7: Electrical disturbance tests for measuring relays and protection equipment Power frequency immunity tests
IEC 60255-24, Electrical relays Part 24: Common format for transient data exchange (COMTRADE) for power systems
IEC 60255-25, Electrical relays Part 25: Electromagnetic emission tests for measuring relays and protection equipment
IEC 60255-26, Measuring relays and protection equipment Part 26: Electromagnetic compatibility requirements
IEC 60255-27, Measuring relays and protection equipment Part 27: Product safety requirements
IEC 60255-5, Electrical Relays Part 5: Insulation coordination for measuring relays and protection equipment Requirements and tests
IEC 60255-6, Electrical relays Part 6: Measuring relays and protection equipment
IEC 60255-8, Electrical relays Part 8: Thermal electrical relays
IEC 60265-1, High-voltage switches Part 1: Switches for rated voltages above 1 kV and less than 52 kV
IEC 60268, Sound system equipment
IEC 60268-16, Sound system equipment Part 16: Objective rating of speech intelligibility by speech transmission index
IEC 60268-3, Sound System Equipment Part 3: Amplifiers
IEC 60269, Low-voltage fuses
IEC 60269-1, Low-voltage fuses Part 1: General requirements
IEC 60269-2, Low voltage fuses Part 2: Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application)
IEC 60269-2-1, Low-voltage fuses Part 2-1: Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application) - Sections I to VI: Examples of types of standardized fuses
-
Electrotechnical standards relevant for the oil and gas industry / 21
IEC 60269-3, Low-voltage fuses Part 3: Supplementary requirements for fuses for use by unskilled persons (fuses mainly for household or similar applications) - Examples of standardized systems of fuses A to F
IEC 60270, High-voltage test techniques Partial discharge measurements
IEC 60282-1, High-voltage fuses Part 1: Current-limiting fuses
IEC 60282-2, High-voltage fuses Part 2: Expulsion fuses
IEC 60287, Electric cables Calculation of the current rating (all parts)
IEC 60287-1-1, Electric cables Calculation of the current rating Part 1-1: Current rating equations (100 % load factor) and calculation of losses - General
IEC 60287-1-2 , Electric cables Calculation of the current rating Part 1: Current rating equations (100 % load factor) and calculations of losses - Section 2: Sheath eddy current loss factors for two circuits in flat formation
IEC 60287-1-3, Electric cables - Calculation of the current rating Part 1-3: Current rating equations (100 % load factor) and calculation of losses - Current sharing between parallel single-core cables and calculation of circulating current losses
IEC 60287-2-1 , Electric cables - Calculation of the current rating Part 2-1: Thermal resistance - Calculation of thermal resistance
IEC 60287-2-2 , Electric cables - Calculation of the current rating Part 2: Thermal resistance - Section 2: A method for calculating reduction factors for groups of cables in free air, protected from solar radiation
IEC 60287-3-1 , Electric cables - Calculation of the current rating Part 3-1: Sections on operating conditions - Reference operating conditions and selection of cable type
IEC 60287-3-2 , Electric cables - Calculation of the current rating Part 3: Sections on operating conditions - Section 2: Economic optimization of power cable size
IEC 60287-3-3 , Electric cables - Calculation of the current rating Part 3-3: Sections on operating conditions - Cables crossing external heat sources
IEC 60296, Fluids for electrotechnical applications Unused mineral insulating oils for transformers and switchgear
IEC 60298, AC Metal Enclosed Switchgear & Control gear for rated voltages above 1kV and up to and including 52kV
IEC 60300, Dependability management
IEC 60300-1, Dependability management Part 1: Dependability management systems
IEC 60300-2, Dependability management Part 2: Guidelines for dependability management
-
Electrotechnical standards relevant for the oil and gas industry / 22
IEC 60300-3-1 , Dependability management Part 3-1: Application guide Analysis techniques for dependability Guide on methodology
IEC 60300-3-10, Dependability management Part 3-10: Application guide Maintainability
IEC 60300-3-11, Dependability management Part 3-11: Application guide Reliability centred maintenance
IEC 60300-3-12, Dependability management Part 3-12: Application guide Integrated logistic support
IEC 60300-3-14, Dependability management Application guide Maintenance and maintenance support
IEC 60300-3-15, Dependability management Application guide Engineering of system dependability
IEC 60300-3-16, Dependability management Part 3-16: Application guide Guidelines for the specification of maintenance support services
IEC 60300-3-2 , Dependability management Part 3-2: Application guide Collection of dependability data from the field
IEC 60300-3-3 , Dependability management Application guide Life cycle costing
IEC 60300-3-4 , Draft Document Dependability Management Part 3: Application Guide Section 4: Guide to the Specification of Dependability Requirements
IEC 60300-3-5 , Dependability management Part 3-5: Application guide Reliability test conditions and statistical test principles
IEC 60304, Standard colours for insulation for low-frequency cables and wires
IEC 60309, Plugs, socket-outlets and couplers for industrial proposes
IEC 60309-1, Plugs, socket-outlets and couplers for industrial purposes Part 1: General requirements
IEC 60309-2, Plugs, socket-outlets and couplers for industrial purposes Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories
IEC 60309-4, Plugs, socket-outlets and couplers for industrial purposes Part 4: Switched socket-outlets and connectors with or without interlock
IEC 60317, Specifications for particular types of winding wires
IEC 60331, Tests for electric cables under fire conditions Circuit integrity
IEC 60331-1, Tests for electric cables under fire conditions Circuit integrity Part 1: Test method for fire with shock at a temperature of at least 830 C for cables of rated voltage up to and including 0,6/1,0 kV and with an overall diameter exceeding 20 mm
-
Electrotechnical standards relevant for the oil and gas industry / 23
IEC 60331-11, Tests for electric cables under fire conditions Circuit integrity Part 11: Apparatus - Fire alone at a flame temperature of at least 750 C
IEC 60331-2, Tests for electric cables under fire conditions Circuit integrity Part 2: Test method for fire with shock at a temperature of at least 830 C for cables of rated voltage up to and including 0,6/1,0 kV and with an overall diameter not exceeding 20 mm
IEC 60331-21, Tests for electric cables under fire conditions Circuit integrity Part 21: Procedures and requirements Cables of rated voltage up to and including 0,6/1,0 kV
IEC 60331-23, Tests for electric cables under fire conditions Circuit integrity Part 23: Procedures and requirements - Electric data cables
IEC 60331-25, Tests for electric cables under fire conditions Circuit integrity Part 25: Procedures and requirements Optical fibre cables
IEC 60331-3, Tests for electric cables under fire conditions Circuit integrity Part 3: Test method for fire with shock at a temperature of at least 830 C for cables of rated voltage up to and including 0,6/1,0 kV tested in a metal enclosure
IEC 60332, Tests on electric and optical fibre cables under fire conditions
IEC 60332-1, Tests on electric and optical fibre cables under fire conditions Part 1: Test for vertical flame propagation for a single insulated wire or cable
IEC 60332-1-1, Tests on electric and optical fibre cables under fire conditions Part 1-1: Test for vertical flame propagation for a single insulated wire or cable Apparatus
IEC 60332-1-2, Tests on electric and optical fibre cables under fire conditions Part 1-2: Test for vertical flame propagation for a single insulated wire or cable Procedure for 1 kW pre-mixed flame
IEC 60332-1-3 , Tests on electric and optical fibre cables under fire conditions Part 1-3: Test for vertical flame propagation for a single insulated wire or cable Procedure for determination of flaming droplets/particles
IEC 60332-2-1 , Tests on electric and optical fibre cables under fire conditions Part 2-1: Test for vertical flame propagation for a single small insulated wire or cable Apparatus
IEC 60332-2-2 , Tests on electric and optical fibre cables under fire conditions Part 2-2: Test for vertical flame propagation for a single small insulated wire or cable Procedure for diffusion flame
IEC 60332-3, Tests on electric cables under fire conditions (various Parts) - Test for vertical flame spread of vertically mounted bunched wires or cables
IEC 60332-3-10, Tests on electric and optical fibre cables under fire conditions Part 3-10: Test for vertical flame spread of vertically-mounted bunched wires or cables Apparatus
IEC 60332-3-21, Tests on electric cables under fire conditions Part 3-21: Test for vertical flame spread of vertically-mounted bunched wires or cables Category A F/R
-
Electrotechnical standards relevant for the oil and gas industry / 24
IEC 60332-3-22, Tests on electric cables under fire conditions Part 3-22: Test for vertical flame spread of vertically-mounted bunched wires or cables Category A
IEC 60332-3-23, Tests on electric and optical fibre cables under fire conditions Part 3-23: Test for vertical flame spread of vertically-mounted bunched wires or cables Category B
IEC 60332-3-24, Tests on electric and optical fibre cables under fire conditions Part 3-24: Test for vertical flame spread of vertically-mounted bunched wires or cables Category C
IEC 60332-3-25, Tests on electric and optical fibre cables under fire conditions Part 3-25: Test for vertical flame spread of vertically-mounted bunched wires or cables Category D
IEC 60335, Household and similar electrical appliances (relevant parts)
IEC 60335-1, Household and similar electrical appliances Safety Part 1: General requirements
IEC 60335-2-29, Household and similar electrical appliances Safety Part 2-29: Particular requirements for battery chargers
IEC 60354, Loading Guide For Oil-Immersed Transformers
IEC 60364, Low-voltage electrical installations
IEC 60364-1, Low-voltage electrical installations Part 1: Fundamental principles, assessment of general characteristics, definitions
IEC 60364-4-41, Low-voltage electrical installations Part 4-41: Protection for safety Protection against electric shock
IEC 60364-4-43, Low-voltage electrical installations Part 4-43: Protection for safety Protection against overcurrent
IEC 60364-4-44, Low-voltage electrical installations Part 4-44: Protection for safety Protection against voltage disturbances and electromagnetic disturbances.
IEC 60364-5-52, Low-voltage electrical installations Part 5-52: Selection and erection of electrical equipment Wiring systems
IEC 60364-5-53, Electrical installations of buildings Part 5-53: Selection and erection of electrical equipment Isolation, switching and control
IEC 60364-5-54, Low-voltage electrical installations Part 5-54: Selection and erection of electrical equipment Earthing arrangement and protective conductors
IEC 60364-5-548, Electrical installations of buildings Part 5: Selection and erection of electrical equipment Section 548: Earthing arrangements and Equipotential Bonding for information technology installations
IEC 60364-5-55, Electrical installations of buildings Part 5-55: Selection and erection of electrical equipment Other equipment
IEC 60364-6, Low voltage electrical installations Part 6: Verification
-
Electrotechnical standards relevant for the oil and gas industry / 25
IEC 60364-7-710, Electrical installations of buildings Part 7-710: Requirements for special installations or locations Medical locations
IEC 60364-7-712, Electrical installations of buildings Part 7-712: Requirements for special installations or locations Solar photovoltaic (PV) power supply systems
IEC 60376, Specification of technical grade sulfur hexafluoride (SF6) for use in electrical equipment
IEC 60383, Plugs and socket-outlets for domestic and similar general use standardized in member countries of IEC
IEC 60398, Industrial electroheating installations General test methods
IEC 60400, Lampholders for tubular fluorescent lamps and starterholders
IEC 60417, Graphical symbols for use on equipment
IEC 60417-1, Graphical symbols for use on equipment Part 1: Overview and application
IEC 60422, Mineral insulating oils in electrical equipment Supervision and maintenance guidance
IEC 60432, Incandescent lamps Safety specifications
IEC 60432-1, Incandescent lamps Safety specifications Part 1: Tungsten filament lamps for domestic and similar general lighting purposes
IEC 60433, Insulators for overhead lines with a nominal voltage above 1 000 V Ceramic insulators for a.c. systems Characteristics of insulator units of the long rod type
IEC 60439, Low-voltage switchgear and control gear assemblies.
IEC 60439-1, Low-voltage switchgear and control gear assemblies Part 1: Type-tested and partially type-tested assemblies
IEC 60439-2, Low-voltage switchgear and controlgear assemblies Part 2: Particular requirements for busbar trunking systems (busways)
IEC 60439-4, Low-voltage switchgear and controlgear assemblies Part 4: Particular requirements for assemblies for construction sites (ACS)
IEC 60446, Basic and safety principles for man-machine interface, marking and identification Identification of conductors by colours
IEC 60447, Basic and safety principles for man-machine interface, marking and identification Actuating principles
IEC 60449, Voltage bands for electrical installations of buildings
IEC 60450, Measurement of the average viscometric degree of polymerization of new and aged cellulosic electrically insulating materials
IEC 60454-2, Specifications for pressure-sensitive adhesive tapes For electrical purposes Part 2: Methods of test
-
Electrotechnical standards relevant for the oil and gas industry / 26
IEC 60470, High-voltage alternating current contactors
IEC 60473, Dimensions for panel-mounted indicating and recording electrical measuring instruments
IEC 60478, Stabilized power supplies, DC output
IEC 60479, Guide to effects of current on human beings and livestock (Parts 1-4)
IEC 60480, Guidelines for the checking and treatment of sulphur hexafluoride (SF6) taken from electrical equipment and specification for its re-use
IEC 60487, Methods of measurement for equipment used in terrestrial radio-relay systems.
IEC 60502, Power cables with extruded insulation and their accessories for rated voltages from 1 kV (Um = 1,2 kV) up to 30 kV (Um = 36 kV)
IEC 60502-1, Power cables with extruded insulation and their accessories for rated voltages from 1 kV (Um = 1,2 kV) up to 30 kV (Um = 36 kV) Part 1: Cables for rated voltages of 1 kV (Um = 1,2 kV) and 3 kV (Um = 3,6 kV)
IEC 60502-2, Power cables with extruded insulation and their accessories for rated voltages from 1 kV (Um = 1,2 kV) up to 30 kV (Um = 36 kV) Part 2: Cables for rated voltages from 6 kV (Um = 7,2 kV) up to 30 kV (Um = 36 kV)
IEC 60502-4, Power cables with extruded insulation and their accessories for rated voltages from 1 kV (Um = 1,2 kV) up to 30 kV (Um = 36 kV) Part 4: Test requirements on accessories for cables with rated voltages from 6 kV (Um = 7,2 kV) up to 30 kV (Um = 36 kV)
IEC 60519-10, Safety in electroheat installations Part 10: Particular requirements for electrical resistance trace heating systems for industrial and commercial applications
IEC 60529, Degrees of protection provided by enclosures (IP Code)
IEC 60533, Electrical and electronic installations in ships Electromagnetic compatibility
IEC 60534, Industrial-process control valves
IEC 60534-1, Industrial-process control valves Part 1: Control valve terminology and general considerations
IEC 60534-2, Industrial-process control valves Part 2: Flow capacity
IEC 60534-2-1, Industrial-process control valves Part 2-1: Flow capacity Sizing equations for fluid flow under installed conditions
IEC 60534-2-3 , Industrial-process control valves Part 2-3: Flow capacity Test procedures
IEC 60534-2-4 , Industrial-process control valves Part 2-4: Flow capacity Inherent flow characteristics and rangeability
IEC 60534-2-5 , Industrial-process control valves Part 2-5: Flow capacity Sizing equations for fluid flow through multistage control valves with interstage recovery
-
Electrotechnical standards relevant for the oil and gas industry / 27
IEC 60534-3-1 , Industrial-process control valves Part 3-1: Dimensions Face-to-face dimensions for flanged, two-way, globe-type, straight pattern and centre-to-face dimensions for flanged, two-way, globe-type, angle pattern control valves
IEC 60534-3-2, Industrial-process control valves Part 3-2: Dimensions Face-to-face dimensions for rotary control valves except butterfly valves
IEC 60534-3-3 , Industrial-process control valves Part 3-3: Dimensions End-to-end dimensions for buttweld, two-way, globe-type, straight pattern control valves
IEC 60534-4, Industrial-process control valves Part 4: Inspection and routine testing
IEC 60534-5, Industrial-process control valves Part 5: Marking
IEC 60534-6-1, Industrial-process control valves Part 6: Mounting details for attachment of positioners to control valves Section 1: Positioner mounting on linear actuators
IEC 60534-6-2 , Industrial-process control valves Part 6-2: Mounting details for attachment of positioners to control valves Positioner mounting on rotary actuators
IEC 60534-7, Industrial process control valves Part 7: Control valve data sheet
IEC 60534-8-3, Industrial-process control valves Part 8-3: Noise considerations Control valve aerodynamic noise prediction method
IEC 60534-8-4 , Industrial-process control valves Part 8-4: Noise considerations Prediction of noise generated by hydrodynamic flow
IEC 60536, Classification of electrical and electronic equipment with regard to protection against electric shock.
IEC 60549, High-voltage fuses for the external protection of shunt power capacitors
IEC 60567, Oil-filled electrical equipment - Sampling of gases and analysis of free and dissolved gases Guidance
IEC 60584-1, Thermocouples Part 1: Reference tables
IEC 60584-2, Thermocouples Part 2: Tolerances
IEC 60584-3, Thermocouples Part 3: Extension and compensating cables - Tolerances and identification system
IEC 60598, Luminaires
IEC 60598-1, Luminaires Part 1: General requirements and tests
IEC 60598-2-1, Luminaires Part 2: Particular requirements Section 1: Fixed general purpose luminaires
IEC 60598-2-2, Luminaires Part 2: Particular requirements Section 2: Recessed luminaires
-
Electrotechnical standards relevant for the oil and gas industry / 28
IEC 60598-2-22, Luminaires Part 2-22: Particular requirements Luminaires for emergency lighting
IEC 60598-2-5, Luminaires Part 2-5: Particular requirements Floodlights
IEC 60598-2-6, Luminaires Part 2: Particular requirements Section 6: Luminaires with built-in transformers for filament lamps
IEC 60599, Mineral oil-impregnated electrical equipment in service Guide to the interpretation of dissolved and free gases analysis
IEC 60616, Terminal and tapping markings for power transformers
IEC 60617, Graphical symbols for diagrams DATABASE
IEC 60622, Secondary cells and batteries containing alkaline or other non-acid electrolytes Sealed nickel-cadmium prismatic rechargeable single cells
IEC 60623, Secondary cells and batteries containing alkaline or other non-acid electrolytes Vented nickel-cadmium prismatic rechargeable single cells
IEC 60644, Specification for high-voltage fuse-links for motor circuit applications
IEC 60654, Industrial-process measurement and control equipment Operating conditions
IEC 60654-1, Industrial-process measurement and control equipment Operating conditions Part 1: Climatic conditions
IEC 60654-2, Operating conditions for industrial-process measurement and control equipment. Part 2: Power
IEC 60654-3, Operating conditions for industrial-process measurement and control equipment Part 3: Mechanical influences
IEC 60654-4, Operating conditions for industrial-process measurement and control equipment. Part 4: Corrosive and erosive influences
IEC 60662, High-pressure sodium vapour lamps
IEC 60664, Insulation coordination for equipment within low-voltage systems
IEC 60664-1, Insulation coordination for equipment within low-voltage systems Part 1: Principles, requirements and tests
IEC 60664-3, Insulation coordination for equipment within low-voltage systems Part 3: Use of coating, potting or moulding for protection against pollution
IEC 60669, Switches for household and similar fixed-electrical installations (all parts)
IEC 60684-1, Flexible Insulating sleeving Part 1: Definitions and general requirements
IEC 60688, Electrical measuring transducers for converting a.c. electrical quantities to analogue or digital signals
-
Electrotechnical standards relevant for the oil and gas industry / 29
IEC 60694, Common specifications for high-voltage switchgear and controlgear standards
IEC 60695, Fire hazard testing
IEC 60695-2-10, Fire Hazard testing Part 2-10: Glowing/hot-wire based test methods Glow-wire apparatus and common test procedure
IEC 60695-2-11, Fire hazard testing Part 2-11: Glowing/hot-wire based test methods Glow-wire flammability test method for end-products
IEC 60706, Maintainability of equipment
IEC 60706-2, Maintainability of equipment Part 2: Maintainability requirements and studies during the design and development phase
IEC 60706-3, Maintainability of equipment Part 3: Verification and collection, analysis and presentation of data
IEC 60721, Classification of environmental conditions
IEC 60721-2-1, Classification of environmental conditions Part 2-1: Environmental conditions appearing in nature Temperature and humidity
IEC 60721-2-2 , Environmental conditions appearing in nature Precipitation and wind
IEC 60721-3-2 , Guidance for the correlation and transformation of environmental condition classes of IEC 60721-3 to the environmental tests of IEC 60068 Transportation
IEC 60721-3-3 , Classification of environmental conditions Part 3-3: Classification of groups of environmental parameters and their severities Stationary use at weatherprotected locations
IEC 60721-3-4, Classification of environmental conditions Part 3: Classification of groups of environmental parameters and their severities Section 4: Stationary use at non-weatherprotected locations
IEC 60721-3-6, Classification of environmental conditions Part 3: Classification of groups of environmental parameters and their severities Ship environment
IEC 60724, Short-circuit temperature limits of electric cables with rated voltages of 1 kV (Um = 1,2 kV) and 3 kV (Um = 3,6 kV)
IEC 60724, Guide to the short-circuit temperature limits of electric cables
IEC 60726, Loading guide for dry-type power transformers
IEC 60745, Hand-held motor-operated electric tools Safety
IEC 60751, Industrial platinum resistance thermometers and platinum temperature sensors
IEC 60754, Test on gases evolved during combustion of materials from cables
IEC 60754-1, Test on gases evolved during combustion of materials from cables Part 1: Determination of the amount of halogen acid gas
-
Electrotechnical standards relevant for the oil and gas industry / 30
IEC 60754-2, Test on gases evolved during combustion of materials from cables Part 2: Determination of acidity (by pH measurement) and conductivity
IEC 60770-1, Transmitters for use in industrial-process control systems Part 1: Methods for performance evaluation
IEC 60793-1, Optical fibres Part 1: Measurement methods and test procedures
IEC 60793-1-1, Optical fibres Part 1-1: Measurement methods and test procedures General and guidance
IEC 60793-2, Optical fibres Part 2: Product specifications General
IEC 60793-2-10, Optical fibres Part 2-10: Product specifications Sectional specification for category A1 multimode fibres
IEC 60793-2-20, Optical fibres Part 2-20: Product specifications Sectional specification for category A2 multimode fibres
IEC 60793-2-30, Optical fibres Part 2-30: Product specifications Sectional specification for category A3 multimode fibres
IEC 60793-2-40, Optical fibres Part 2-40: Product specifications Sectional specification for category A4 multimode fibres
IEC 60793-2-50, Optical fibres Part 2-50: Product specifications Sectional specification for class B single-mode fibres
IEC 60793-2-60, Optical fibres Part 2-60: Product specifications Sectional specification for category C single-mode intraconnection fibres
IEC 60794, Optical fibre cables
IEC 60794-1, Optical fibre cables Part 1: Generic specification
IEC 60794-1-1, Optical fibre cables Part 1-1: Generic specification General
IEC 60794-1-2 , Optical fibre cables Part 1-2: Generic specification Basic optical cable test procedures
IEC 60794-2, Optical fibre cables Part 2: Indoor cables Sectional specification
IEC 60794-2-10, Optical fibre cables Part 2-10: Indoor cables Family specification for simplex and duplex cables
IEC 60794-2-11, Optical fibre cables Part 2-11: Indoor cables Detailed specification for simplex and duplex cables for use in premises cabling
IEC 60794-2-20, Optical fibre cables Part 2-20: Indoor cables Family specification for multi-fibre optical distribution cables
IEC 60794-2-21, Optical fibre cables Part 2-21: Indoor cables Detailed specification for multi-fibre optical distribution cables for use in premises cabling
-
Electrotechnical standards relevant for the oil and gas industry / 31
IEC 60794-2-30, Optical fibre cables Part 2-30: Indoor cables Family specification for ribbon cables
IEC 60794-2-31, Optical fibre cables Part 2-31: Indoor cables Detailed specification for optical fibre ribbon cables for use in premises cabling
IEC 60794-2-40, Optical fibre cables Part 2-40: Indoor optical fibre cables Family specification for A4 fibre cables
IEC 60794-2-41, Optical fibre cables Part 2-41: Indoor cables Product specification for simplex and duplex buffered A4 fibres
IEC 60794-2-42, Optical fibre cables Part 2-42: Indoor optical fibre cables Product specification for simplex and duplex cables with A4 fibres
IEC 60794-2-50, Optical fibre cables Part 2-50: Indoor cables Family specification for simplex and duplex cables for use in terminated cable assemblies
IEC 60794-2-51, Optical fibre cables Part 2-51: Indoor optical fibre cables Product specification for simplex and duplex cables for use in patchcords for controlled environment
IEC 60794-3, Optical fibre cables Part 3: Sectional specification Outdoor cables
IEC 60794-3-10, Optical fibre cables Part 3-10: Outdoor cables Family specification for duct, directly buried and lashed aerial optical telecommunication cables
IEC 60794-3-11, Optical fibre cables Part 3-11: Outdoor cables Product specification for duct, directly buried, and lashed aerial single-mode optical fibre telecommunication cables
IEC 60794-3-12, Optical fibre cables Part 3-12: Outdoor cables Detailed specification for duct and directly buried optical telecommunication cables for use in premises cabling
IEC 60794-3-20, Optical fibre cables Part 3-20: Outdoor cables Family specification for self-supporting aerial telecommunication cables
IEC 60794-3-21, Optical fibre cables Part 3-21: Outdoor cables Detailed specification for
IEC 60794-3-30, Optical fibre cables Part 3-30: Outdoor cables Family specification for optical telecommunication cables for lakes, river crossings and coastal application
IEC 60794-3-40, Optical fibre cables Part 3-40: Outdoor cables Family specification for sewer cables and conduits for installation by blowing and/or pulling in non-man accessible storm and sanitary sewers
IEC 60794-3-50, Optical fibre cables Part 3-50: Outdoor cables Family specification for gas pipe cables and subducts for installation by blowing and/or pulling/dragging in gas pipes
IEC 60794-3-60, Optical fibre cables Part 3-60: Outdoor cables Family specification for drinking water pipe cables and subducts for installation by blowing and/or pulling/dragging/floating in drinking water pipes
-
Electrotechnical standards relevant for the oil and gas industry / 32
IEC 60794-4, Optical fibre cables Part 4: Sectional specification - Aerial optical cables along electrical power lines
IEC 60794-4-10, Optical fibre cables Part 4-10: Aerial optical cables along electrical power lines Family specification for OPGW (Optical Ground Wires)
IEC 60794-4-20, Optical fibre cables Part 4-20: Aerial optical cables along electrical power lines Family specification for ADSS (All Dielectric Self Supported) Optical cables
IEC 60794-5, Optical fibre cables Part 5: Sectional specification Microduct cabling for installation by blowing
IEC 60794-5-10, Optical fibre cables: Part 5-10 Family specification for outdoor microduct optical fibre cables, microducts and protected microducts for installation by blowing
IEC 60794-5-20, Optical fibre cables Part 5-20: Family specification for outdoor microduct fibre units, microducts and protected microducts for installation by blowing
IEC 60801, Electromagnetic compatibility for industrial-process measurement and control equipment.
IEC 60811, Common test methods for insulating and sheathing materials of electric cables
IEC 60811-2-1, Common test methods for insulating and sheathing materials of electric and optical cables Part 2-1: Methods specific to elastomeric compounds - Ozone resistance, hot set and mineral oil immersion tests
IEC 60812, Analysis techniques for system reliability Procedure for failure mode and effects analysis (FMEA)
IEC 60814, Insulating liquids Oil-impregnated paper and pressboard Determination of water by automatic coulometric Karl Fischer titration
IEC 60815, Guide for the selection of insulators in respect of polluted conditions
IEC 60825, Safety of laser products (all parts)
IEC 60831, Shunt power capacitors of the self-heating type for a.c. systems having a rated voltage up to and including 1kV
IEC 60835-3-5, Methods of measurement for equipment used in digital microwave radio transmission systems Part 3: Measurement on satellite earth stations Section 5: Up- and down-converters
IEC 60840, Power cables with extruded insulation and their accessories for rated voltages above 30 kV (Um=36 kV) up to 150 kV (Um =170 kV) Test methods and requirements.
IEC 60851, Stationary lead-acid batteries
IEC 60865, Short-circuit currents Calculation of effects
-
Electrotechnical standards relevant for the oil and gas industry / 33
IEC 60870-1-2, Telecontrol equipment and systems Part 1: General considerations Section 2: Guide for specifications
IEC 60870-5-103, Telecontrol equipment and systems Part 5-103: Transmission protocols Companion Standard for the informative interface of protection equipment
IEC 60871, Shunt capacitors for a.c. power systems having a rated voltage above 1 000 V
IEC 60871-1, Shunt capacitors for a.c. power systems having a rated voltage above 1 000 V Part 1: General
IEC 60871-4, Shunt capacitors for AC power systems having a rated voltage above 1 000V Part 4: Internal fuses
IEC 60877, Procedures for ensuring the cleanliness of industrial-process measurement and control equipment in oxygen service
IEC 60884, Plugs and socket-outlets for household and similar purposes (all parts)
IEC 60885, Electrical test methods for electric cables Part 2: Partial discharge tests
IEC 60885-2, Electrical test methods for electric cables Part 2: Partial discharge tests
IEC 60888, Zinc-coated steel wires for stranded conductors
IEC 60894, Guide for test procedure for the measurement of loss tangent of coils and bars for machine windings
IEC 60896, Stationary lead-acid batteries General requirements and methods of testing.
IEC 60896-11, Stationary lead-acid batteries Part 11: Vented types General requirements and methods of test
IEC 60896-21, Stationary lead-acid batteries Part 21: Valve regulated types Methods of test
IEC 60896-22, Stationary lead-acid batteries Part 22: Valve regulated types Requirements
IEC 60898, Electrical accessories Circuit-breakers for overcurrent protection for household and similar installations
IEC 60898-1, Electrical accessories Circuit-breakers for overcurrent protection for household and similar installations Part 1: Circuit-breakers for a.c. operation
IEC 60900, Live working Hand tools for use up to 1 000 V a.c. and 1 500 V d.c
IEC 60904, Photovoltaic devices
IEC 60905, Loading Guide For Dry-Type Power Transformers
IEC 60906, IEC system of plugs and socket-outlets for household and similar purposes (all parts)
IEC 60909, Short-circuit currents in three-phase a.c. systems
-
Electrotechnical standards relevant for the oil and gas industry / 34
IEC 60909-0, Short-circuit currents in three-phase a.c. systems Part 0: Calculation of currents
IEC 60909-1, Short-circuit currents in three-phase a.c. systems Part 1: Factors for the calculation of short-circuit currents according to IEC 60909-0
IEC 60909-2, Short-circuit currents in three-phase a.c. systems Part 2: Data of electrical equipment for short-circuit current calculations
IEC 60909-3, Short-circuit currents in three-phase a.c. systems Part 3: Currents during two separate simultaneous line-to-earth short circuits and partial short-circuit currents flowing through earth
IEC 60909-4, Short-circuit currents in three-phase a.c. systems Part 4: Examples for the calculation of short-circuit currents
IEC 60921, Ballasts for tubular fluorescent lamps Performance requirements
IEC 60923, Auxiliaries for lamps Ballasts for discharge lamps (excluding tubular fluorescent lamps) Performance requirements
IEC 60927, Auxiliaries for lamps Starting devices (other than glow starters) Performance requirements
IEC 60929, AC-supplied electronic ballasts for tubular fluorescent lamps Performance requirements
IEC 60931-3, Shunt power capacitors of the non-self-healing type for a.c. systems having a rated voltage up to and including 1 000V Part 3: Internal fuses
IEC 60945, Maritime navigation and radiocommunication equipment and systems General requirements Methods of testing and required test results
IEC 60947, Low-voltage switchgear and controlgear
IEC 60947-1, Low-voltage switchgear and control gear Part 1: General rules
IEC 60947-2, Low-voltage switchgear and controlgear Part 2: Circuit-breakers
IEC 60947-3, Low-voltage switchgear and controlgear Part 3: Switches, disconnectors, switch-disconnectors and fuse-combination units
IEC 60947-4-1, Low-voltage switchgear and controlgear Part 4-1: Contactors and motor-starters Electromechanical contactors and motor-starters
IEC 60947-4-2 , Low-voltage switchgear and controlgear Part 4-2: Contactors and motor-starters AC semiconductor motor controllers and starters
IEC 60947-5-1 , Low-voltage switchgear and controlgear Part 5-1: Control circuit devices and switching elements Electromechanical control circuit devices
IEC 60947-5-2 , Low-voltage switchgear and controlgear Part 5-2: Control circuit devices and switching elements Proximity switches
-
Electrotechnical standards relevant for the oil and gas industry / 35
IEC 60947-5-6, Low-voltage switchgear and control gear
IEC 60947-6-1 , Low-voltage switchgear and controlgear Part 6-1: Multiple function equipment Transfer switching equipment
IEC 60947-6-2, Low-voltage switchgear and controlgear Part 6-2: Multiple function equipment Control and protective switching devices (or equipment) (CPS)
IEC 60949, Calculation of thermally permissible short-circuit currents, taking into account non-adiabatic heating effects
IEC 60950-1, Information technology equipment Safety Part 1: General requirements
IEC 60968, Self-ballasted lamps for general lighting services Safety requirements
IEC 60969, Self-ballasted lamps for general lighting services Performance requirements
IEC 60974, Arc welding equipment
IEC 60974-1, Arc welding equipment Welding power sources
IEC 60986, Short-circuit temperature limits of electric cables with rated voltages from 6 kV (Um = 7,2 kV) up to 30 kV (Um = 36 kV)
IEC 60993, Electrolyte for vented nickel-cadmium cells
IEC 61000, Electromagnetic compatibility
IEC 61000-1-1, Electromagnetic compatibility (EMC) Part 1: General Section 1: Application and interpretation of fundamental definitions and terms
IEC 61000-2, Electromagnetic compatibility (EMC) Part 2: Environment
IEC 61000-2-1, Electromagnetic compatibility (EMC) Part 2: Environment Section 1: Description of the environment Electromagnetic environment for low-frequency conducted disturbances and signalling in public power supply systems
IEC 61000-2-2, Electromagnetic compatibility (EMC) Part 2-2: Environment Compatibility levels for low-frequency conducted disturbances and signalling in public low-voltage power supply systems
IEC 61000-2-4 , Electromagnetic compatibility (EMC) Part 2-4: Environment Compatibility levels in industrial plants for low-frequency conducted disturbance.
IEC 61000-2-5, Electromagnetic compatibility (EMC) Part 2-5: Environment Description and classification of electromagnetic environments
IEC 61000-3, Electromagnetic compatibility (EMC) Part 3: Limits
IEC 61000-3-12, Electromagnetic compatibility (EMC) Part 3-12: Limits Limits for harmonic currents produced by equipment connected to public low-voltage systems with input current >16 A and 75 A per phase
-
Electrotechnical standards relevant for the oil and gas industry / 36
IEC 61000-3-2 , Electromagnetic compatibility (EMC) Part 3-2: Limits Limits for harmonic current emissions (equipment input current 16 A per phase)
IEC 61000-3-4 , Electromagnetic compatibility (EMC) Part 3-4: Limits Limitation of emission of harmonic currents in low-voltage power supply systems for equipment with rated current greater than 16 A
IEC 61000-3-6, Electromagnetic compatibility (EMC) Part 3-6: Limits Assessment of emission limits for the connection of distorting installations to MV, HV and EHV power systems
IEC 61000-4, Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques
IEC 61000-4-1 , Electromagnetic compatibility (EMC) Part 4-1: Testing and measurement techniques Overview of IEC 61000-4 series
IEC 61000-4-11, Electromagnetic compatibility (EMC) Part 4-11: Testing and measurement techniques Voltage dips, short interruptions and voltage variations immunity tests
IEC 61000-4-12, Electromagnetic compatibility (EMC) Part 4-12: Testing and measurement techniques Ring wave immunity test
IEC 61000-4-2 , Electromagnetic compatibility (EMC) Part 4-2: Testing and measurement techniques Electrostatic discharge immunity test
IEC 61000-4-3 , Electromagnetic compatibility (EMC) Part 4-3 : Testing and measurement techniques Radiated, radio-frequency, electromagnetic field immunity test
IEC 61000-4-4 , Electromagnetic compatibility (EMC) Part 4-4: Testing and measurement techniques Electrical fast transient/burst immunity test
IEC 61000-4-5, Electromagnetic compatibility (EMC) Part 4-5: Testing and measurement techniques Surge immunity test
IEC 61000-4-6 , Electromagnetic compatibility (EMC) Part 4-6: Testing and measurement techniques Immunity to conducted disturbances, induced by radio-frequency fields
IEC 61000-4-7 , Electromagnetic compatibility (EMC) Part 4-7: Testing and measurement techniques General guide on harmonics and interharmonics measurements and instrumentation, for power supply systems and equipment connected thereto
IEC 61000-4-8, Electromagnetic compatibility (EMC) Part 4-8: Testing and measurement techniques Power frequency magnetic field immunity test
IEC 61000-5, Electromagnetic compatibility (EMC) Part 5: Installation and mitigation guidelines
IEC 61000-5-1 , Electromagnetic compatibility (EMC) Part 5: Installation and mitigation guidelines Section 1: General considerations Basic EMC publication
IEC 61000-5-2 , Electromagnetic compatibility (EMC) Part 5: Installation and mitigation guidelines Section 2: Earthing and cabling
-
Electrotechnical standards relevant for the oil and gas industry / 37
IEC 61000-6, Electromagnetic compatibility (EMC) Generic standards Immunity for residential, commercial and light-industrial environments
IEC 61000-6-1 , Electromagnetic compatibility (EMC) Part 6-1: Generic standards Immunity for residential, commercial and light-industrial environments
IEC 61000-6-2, Electromagnetic compatibility (EMC) Part 6-2: Generic standards Immunity for industrial environments
IEC 61000-6-3 , Electromagnetic compatibility (EMC) Part 6-3: Generic standards Emission standard for residential, commercial and light-industrial environments
IEC 61000-6-4, Electromagnetic compatibility (EMC) Part 6-4: Generic standards Emission standard for industrial environments
IEC 61000-6-5, Electromagnetic compatibility (EMC) Part 6-5: Generic standards Immunity for power station and substation environments
IEC 61010, Safety requirements for electrical equipment for measurement, control, and laboratory use
IEC 61010-1, Safety requirements for electrical equipment for measurement, control, and laboratory use Part 1: General requirements
IEC 61024, Protection of structures against lighting
IEC 61025, Fault tree analysis (FTA)
IEC 61034, Measurement of smoke density of cables burning under defined conditions
IEC 61034-1, Measurement of smoke density of cables burning under defined conditions Part 1: Test apparatus
IEC 61034-2, Measurement of smoke density of cables burning under defined conditions Part 2: Test procedure and requirements
IEC 61057, Aerial devices with insulating boom used for live working
IEC 61058, Switches for appliances
IEC 61071, Capacitors for power electronics
IEC 61078, Analysis techniques for dependability Reliability block diagram and boolean methods
IEC 61082-1, Preparation of documents used in electrotechnology Part 1: Rules
IEC 61086-1, Coatings for loaded printed wire boards (conformal coatings) Part 1: Definitions, classification and general requirements
IEC 61086-2, Coatings for loaded printed wire boards (conformal coatings) Part 2: Methods of test
IEC 61089, Round wire concentric lay overhead electrical stranded conductors Equipment
-
Electrotechnical standards relevant for the oil and gas industry / 38
IEC 61097, Global maritime distress and safety system (GMDSS) (all parts)
IEC 61099, Specifications for unused synthetic organic esters for electrical purposes
IEC 61109, Composite insulators for a.c overhead lines with a nominal voltage greater than 1 000 V. Definitions, test methods and acceptance criteria
IEC 61111, Live working Electrical insulating matting
IEC 61131, Programmable controllers
IEC 61131-1, Programmable controllers Part 1: General information
IEC 61131-2, Programmable controllers Part 2: Equipment requirements and tests
IEC 61131-3, Programmable controllers Part 3: Programming languages
IEC 61131-4 , Programmable controllers Part 4: User guidelines
IEC 61131-5, Programmable controllers Part 5: Communications
IEC 61140, Protection against electric shock Common aspects for installation and equipment
IEC 61146, Methods of measurement for video cameras (PAL/SECAM/NTSC)
IEC 61158, Digital data communications for measurement and control Fieldbus for use in industrial control systems
IEC 61158-2, Industrial communication networks Fieldbus specifications Part 2: Physical layer specification and service definition
IEC 61165, Application of Markov techniques
IEC 61167, Metal halide lamps
IEC 61181, Mineral oil-filled electrical equipment Application of dissolved gas analysis (DGA) to factory tests on electrical equipment
IEC 61195, Double-capped fluorescent lamps Safety specifications
IEC 61200-704, Electrical installation guide Part 704: Construction and demolition site installations
IEC 61204, Low-voltage power supply devices, d.c. output Performance characteristics
IEC 61215, Crystalline silicon terrestrial photovoltaic (PV) modules - Design qualification and type approval
IEC 61230, Live working Portable equipment for earthing or earthing and short-circuiting
IEC 61231, International lamp coding system (ILCOS)
IEC 61238-1, Compression and mechanical connectors for power cables
-
Electrotechnical standards relevant for the oil and gas industry / 39
IEC 61241, Electrical apparatus for use in the presence of combustible dusts
IEC 61241-10, Electrical apparatus for use in the presence of combustible dust Part 10: Classification of areas where combustible dusts are or may be present
IEC 61241-4, Electrical apparatus for use in the presence of combustible dust Part 4: Type of protection "pD"
IEC 61285, Industrial process control Safety of analyzer houses
IEC 61293, Marking of electrical equipment with ratings related to electrical supply Safety requirements
IEC 61310-1, Safety of machinery Indication, marking and actuation Part 1: Requirements for visual, acoustic and tactile signals
IEC 61312, Protection against lightning electromagnetic impulse
IEC 61326, Electrical equipment for measurement, control and laboratory use EMC requirements General requirements
IEC 61340-4-1, Electrostatics Part 4-1: Standard test methods for specific applications Electrical resistance of floor coverings and installed floors
IEC 61347, Lamp controlgear
IEC 61363-1, Electrical installations of ships and mobile and fixed offshore units Part 1: Procedures for calculating short circuit currents in three phase a.c.
IEC 61378, Convertor transformers
IEC 61378-1, Convertor transformers Part 1: Transformers for industrial applications
IEC 61378-3, Converter transformers Part 3: Application guide
IEC 61400-24, Wind turbines Part 24: Lightning protection
IEC 61427, Secondary cells and batteries for photovoltaic energy systems (PVES) General requirements and methods of test
IEC 61427-1, Secondary cells and batteries for renewable energy storage - General requirements and methods of test Part 1: Photovoltaic off-grid application
IEC 61434, Secondary cells and batteries containing alkaline or other non-acid electrolytes Guide to designation of current in alkaline secondary cell and battery standards
IEC 61439, Low-voltage switchgear and control gear assemblies
IEC 61439-0, Low-voltage switchgear and controlgear assemblies Part 0: Guide to specifying assemblies
IEC 61439-1, Low-voltage switchgear and controlgear assemblies Part 1: General rules
-
Electrotechnical standards relevant for the oil and gas industry / 40
IEC 61439-2, Low-voltage switchgear and controlgear assemblies Part 2: Power switchgear and controlgear assemblies
IEC 61439-3, Low-voltage switchgear and controlgear assemblies Part 3: Distribution boards
IEC 61439-4, Low-voltage switchgear and controlgear assemblies Part 4: Assemblies for construction sites (ACS)
IEC 61439-5, Low-voltage switchgear and controlgear assemblies Part 5: Assemblies for power distribution in public networks
IEC 61439-6, Low-voltage switchgear and controlgear assemblies Part 6: Busbar trunking systems (busways)
IEC 61442, Test methods for accessories for power cables
IEC 61443, Short-circuit temperature limits of electric cables with rated voltages above 30 kV (Um = 36 kV)
IEC 61466, Composite string insulator units for overhead lines with a nominal voltage greater than 1 000 V
IEC 61478, Live working Ladders of insulating material
IEC 61508, Functional safety of electrical/electronic/programmable electronic safety-related systems all parts
IEC 61508-1, Functional safety of electrical/electronic/programmable electronic safety-related systems Part 1: General requirements
IEC 61508-2, Functional safety of electrical/electronic/programmable electronic safety-related systems Part 2: Requirements for electrical/electronic/programmable electronic safety-related systems (see Functional Safety and IEC 61508)
IEC 61508-3, Functional safety of electrical/electronic/programmable electronic safety-related systems Part 3: Software requirements (see Functional Safety and IEC 61508)
IEC 61508-4, Functional safety of electrical/electronic/programmable electronic safety-related systems Part 4: Definitions and abbreviations
IEC 61508-5, Functional safety of electrical/electronic/programmable electronic safety related systems Part 5: Examples of methods for the determination of safety integrity levels
IEC 61508-6, Functional safety of electrical/electronic/programmable electronic safety-related systems Part 6: Guidelines on the application of IEC 61508-2 and IEC 61508-3
IEC 61508-7, Functional safety of electrical/electronic/programmable electronic safety-related systems Part 7: Overview of techniques and measures
IEC 61511, Functional safety Safety instrumented systems for the process industry sector
-
Electrotechnical standards relevant for the oil and gas industry / 41
IEC 61511-1, Functional safety Safety instrumented systems for the process industry sector Part 1: Framework, definitions, system, hardware and software requirements
IEC 61511-2, Functional safety Safety instrumented systems for the process industry sector Part 2: Guidelines for the application of IEC 61511-1
IEC 61511-3, Functional safety Safety instrumented systems for the process industry sector Part 3: Guidance for the determination of the required safety integrity levels
IEC 61518, Mating dimensions between differential pressure (type) measuring instruments and flanged-on shut-off devices up to 413 BAR (41,3 MPa)
IEC 61537, Cable management Cable tray systems and cable ladder systems
IEC 61554, Panel mounted equipment Electrical measuring instruments Dimensions for panel mounting
IEC 61557, Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c.
IEC 61557-8, Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. Equipment for testing, measuring or monitoring of protective measurers Part 8: Insulation monitoring devices for IT systems
IEC 61557-9, Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures Part 9: Equipment for insulation fault location in IT systems
IEC 61558, Safety of power transformers, power supplies, reactors and similar products