interior renovation work of nabard regional office … pr… · 2. schedule - interior fixed assets...
TRANSCRIPT
SHETGIRI and ASSOCIATES
No. Description Unit Amount
i TOTAL OF INTERIOR FIXED ASSET WORKS Rs.
ii TOTAL OF FURNITURE WORKS Rs.
iii TOTAL OF MODULAR LOOSE FURNITURE WORKS Rs.
iv TOTAL OF CIVIL WORKS Rs.
v TOTAL OF REPAIRS & RESTORATION WORKS Rs.
ATOTAL COST OF INTERIOR RENOVATION &
FURNISHING WORKS (i + ii + iii + iv + v)Rs.
B TOTAL COST OF ELECTRICAL INSTALLATION WORKS Rs.
C
TOTAL COST FO GREEN BUILDING SYSTEMS (RAIN
WATER HARVESTING SYSTEM) WORKS & EXTERNAL /
OUTDOOR BEAUTIFICATION WORKS
Rs.
D TOTAL COST OF LV SYSTEM WORKS Rs.
E TOTAL COST OF AV SYSTEM WORKS Rs.
FINAL TOTAL OF (A+B+C+D+E) Rs.
GRAND TOTAL Rs.
Please Note : The rates quoted hereinabove shall be Exclusive
of GST and GST shall be additional at actuals.
SEAL AND SIGN OF BIDDER
INTERIOR RENOVATION WORK OF NABARD REGIONAL OFFICE AT 54,
WELLESLEY ROAD, P.B.NO. 5, SHIVAJI NAGAR, PUNE-411005
1. SUMMARY
Sinature and Seal of the bidder Page1
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate (Rs.) Amount (Rs.)
2. SCHEDULE - INTERIOR FIXED ASSETS WORKS
GENERAL NOTES: -
N.B: - The plywood considered in this estimate shall be IS 303 MR grade
Commercial Plywood for all the items of Interior & Furniture works. The rate
shall be inclusive of anti termite coating on all sides to plywood, teak wood
& all the other wooden components of Asian paints or equivalent approved
make.
All internal woodwork / Plywood shall be treated with antitermite
preservative. All internal framework shall be of Aluminium unless otherwise
specified as Teakwood. AII exposed edges of Plywood shall be fixed with
C.P. Teak Lipping of size as directed by Architect. The skinning shall be in
303 MR grade Commercial Plywood unless otherwise specified. All
exposed veneer surfaces shall be finished with melamine polish. The
thickness of the veneer shall be 4.0mm & that of laminate shall be 1.5mm
thk. The approved veneer shall be finished with natural melamine polish of
minimum 2 coats to have desired matt melamine finish where ever
specified. The rates quoted for the item of Partitions & Panelling shall be
inclusive of providing & fixing in between the aluminium frames, 50mm thk
Rockinsul Slabs of Rockwool India Ltd of density 96 kgs / cu.m of standard
width as per the available clear distances between the existing frames as
directed wherever required & instructed.
Rate for full height partition to include the cost of framework above false
ceiling as required to fix the same to the ceiling slab for which no extra
payment shall be made and the rate quoted shall be inclusive of the same.
Measurement of Partition & Panelling shall be limited upto the False Ceiling
level. However the cost towards frameworks to be continued upto the main
ceiling shall be deemed to have been considered in the quoted rates and
no separate payment shall be made for the framework or supporting
elements of partitions / panelling items, above the false ceiling level.
The rate shall be all inclusive of the necessary hardware, fittings, fixtures &
including glass & finishing for the same. The rate shall be also inclusive of
pattas & bands, grooves at any level, any design in veneer, textures etc
including the necessary framing/ openings for Electrical, Telephone & AC
outlets. Further it is important to note that the Glasses wherever specified
for the items of Partitions & Panelling if any shall have bevelled edges as
per the direction & thickness as indicated by the Architect or Engineer in
charge
INTERIOR RENOVATION WORK OF NABARD REGIONAL OFFICE AT 54, WELLESLEY ROAD, P.B.NO. 5, SHIVAJI NAGAR,
PUNE-411005
Sinature and Seal of the bidder Page2
SHETGIRI and ASSOCIATES
PARTITIONS / PANELLING
General Specification for partition :-
Main frame -Aluminium sections of 16 Gauge mentioned are out of size
2"x2" Aluminium section verticals at minimum 1' 6"-2'-0" Centre-Centre
spacing approx. and 2" X 1" size Aluminium sections horizontal at 1' 6"-2-
'0" Centre-Centre spacing approx. Extra frame below slab soffit for conduit
to run above. All verticals shall be secured to the ceiling.
SKIN: - 303 MR grade Commercial Plywood shall be screwed to frame
work on both sides with joints as shown or directed.
SKIRTING : In the same alignment, 3" high in 303 MR grade Commercial
Plywood with a groove finished with laminate / veneer as the case maybe,
or as directed by the Architect.
Finishing :-
VENEER:- 4mm thk natural venner with matching superior approved grade
to be fixed to the plywood having joints as shown or directed complete with
melamine polish finish.
LAMINATE:- Approved laminate shall be of 1.5 mm thick.
Internal Laminate shall be fixed on plywood skins with glue having grooves
as shown or directed. Internal surfaces at specified places shall be 0.8 mm
thick as directed by Architect. The rates quoted for the items of partions &
paneling shall be inclusive of providing & fixing M.S. plate & brackets over
& above the aluminium frame work as directed & wherever instructed for
mounting the TV units & screens etc complete.
IMPORTANT NOTE ON THE DESIGN REQUIREMENTS APPLICABLE IN
CASE OF ALL THE ITEMS OF PARTITIONS & PANELLING: - The design
& the elevation of the various items under the heads: Partition & Panelling
shall be at the complete discretion & directions / instructions of the
Engineer in charge & Architects on site. Wherever instructed & directed,
the rate shall include providing & fixing additional 6mm thk plywood backing
over and above the 303 MR grade Commercial plywood so provided in the
items of partition / panelling to form raised panel design at regular intervals
as directed and to be finished with high end approved 4.0 mm thk veneer
with high end melamine polish (proportion of gloss and matt as directed)
with uniform shade & texture. Incase of 9mm thk plywood used instead of
6mm thk plywood for the raised panels for the items of Partition or Paneling
works, the difference between the cost of 9mm thk plywood and 6mm thk
plywood for the actual quantity of plywood used for the said partition or
panelling items shallacess with cable dump an
The level difference between the said raised panels and recessed panels
shall be finished with approved designer moulding to be finished with high
end (proportion of gloss and matt as directed) melamine polish and shall
also include designer inlays to be finished with high end veneer with high
end melamine polish, pattas & bands at various levels etc in veneer and
melamine polish and combinations of raised and recessed panels with
inlays etc complete to the complete satisfaction of the Architect and
Engineer in charge.
Sinature and Seal of the bidder Page3
SHETGIRI and ASSOCIATES
For all items of Interior Furnishing works & Furniture works, the basic rate
of Laminate considered for all the specifications / BOQ items herein shall
be Rs. 55 / Sq. Fts plus taxes (GST) whereas the basic rate of Veneer,
which shall be high end, uniform and without any variations, 4.0 mm thk
considered for all the specifications / BOQ items herein shall be Rs. 100 /
Sq. Fts plus taxes (GST). Basic rate for Frosted / Designer film of 3M,
Llumar or equivalent approved shall be Rs. 90 / Sq. Fts plus taxes (GST).
The basic rate would be the rate offered to the bidder by the vendor /
supplier after discounts and excluding the cost towards transportation,
freight, loading, unloading etc and also exclusive of taxes (GST).
Necessary documentary evidence in the form of challans & Tax invoices,
details of payments released to the vendor for the purchase of such
materials & including the loading-unloading transport slips needs to be
submitted at the time of billing without which the payment processing shall
not be entacess wit
Further, Corian wherever mentioned in the BOQ (For items of Panelling,
Reception Counter, Furniture elements etc) shall be high end, of desired
and approved color and adhering to the BOQ specifications. Corian
thickness shall be 6mm thk for vertical surfaces & fascias and 12mm thk
for horizontal surfaces shall be provided and with a basic rate of Rs. 1200 /
Sq. Fts plus taxes (GST) for 6mm thk Corian and Rs. 1500 / Sq. Fts plus
taxes (GST) for 12 mm thk Corian.
1 Providing and fixing Full ht. double skin Partitions as per specifications
including skirting, complete as per the design, drawings and instructions in
all respects. The specifications for the said item shall comprise of the
following and with varying finishes as mentioned hereinunder: -
FRAMEWORK -2"x2" Aluminium section of 16 Gauge verticals at minimum
1' 6"-2'-0" Centre spacing approx and 2" X 1" size Aluminium sections
horizontal at 1' 6"-2'-0" Centre spacing approx extra frame below slab soffit
for conduit to run above. All verticals secured to ceiling. Measurement of
the said item shall be upto the False Ceiling level.
SKIN:- Both side with 12mm thk 303 MR grade Commercial Plywood
screwed to frame work on both sides with joints as shown or directed.
SKIRTING : In the same alignment, 3" high in 12mm thk 303 MR grade
Commercial Plywood with a groove finished with laminate / veneer as the
case maybe, or as directed by the Architect.
The rate shall include providing & fixing t.w. beading all throughout the
exposed edges & periphery, sealing all the joints, grooves in finishes,
melamine polish to the mouldings & t.w members, complete as per the
directions of Architect/Client. All Aluminium sections shall be smooth, rust
free, straight, mitred and jointed mechanically.
The finishes for the skinning to be screwed to the framework on both the
sides as duly mentioned above shall comprise of the following types: -
A Both side skins to be finished with 1.5 mm thk Laminate as shown in
drawing or as directed by Architect. 70 Sq. Mts
B (i) Both side skins to be finished with 3.0 mm thk approved quality veneer
finished with high-end melamine polish as shown in drawing or as directed
by Architect. (Quantity considered hereinunder this item shall be partition
with single surface without any raised or recessed panels)
158.59 Sq. Mts
Sinature and Seal of the bidder Page4
SHETGIRI and ASSOCIATES
B (ii) Both side skins to be finished with 3.0 mm thk approved quality veneer
finished with high-end melamine polish as shown in drawing or as directed
by Architect. (Quantity considered herein under this item shall be a
combination of raised and recessed panels of appropriate dimensions and
the rate quoted shall include additional 6mm thk plywood backing for the
raised panels as directed including designer moulding at the edge / junction
of raised and recessed panels including high-end melamine polish to the
surface and moulding matching the polish provided for the panels etc
complete).
130 Sq. Mts
C One side skin to be finished with 1.5mm thk approved laminate & other
side skin with 3.0 mm thk approved quality veneer finished with high-end
melamine polish as shown in drawing or as directed by Architect.180.00 Sq. Mts
D One side skin to be finished with 1.5mm thk approved laminate finish and
the other side skin to be finished with 12mm thk gypsum board and to be
finished with approved acryllic emulsion paint as shown in drawing or as
directed by Architect including necessary grooves etc complete.
37.16 Sq. Mts
E Providing and fixing FRAMEWORK in 2"x2" Aluminium section of 16
Gauge verticals at minimum 1' 6"-2'-0" Centre spacing approx and 2" X 1"
size Aluminium sections horizontal at 1' 6"-2'-0" Centre spacing approx
extra frame below slab soffit for conduit to run above including 12mm thk
designer MDF board on both sides including finishing both sides with PU
machine polish including all the necessary surface preparations, final finish
etc complete of approved shade, colour & texture as shown in drawing or
as directed by Architect, including necessary grooves etc complete.
220.00 Sq. Mts
2 Providing & Fixing full height Semi-Glazed partition as per specifications
including skirting, as per the design, drawings and instructions in all
respects. The specifications for the said item shall comprise of the following
and with varying finishes as mentioned hereinunder: -
FRAMEWORK - 2"x2" Aluminium section of 16 Gauge verticals, not
exceed 1' 6"-2'-0" centres and 2" X 1" size Aluminium sections horizontal at
floor level / skirting ht, 3'-0" level and door height at 7'-0" level. All verticals
secured to ceiling. Measurement of the said item shall be upto the False
Ceiling level.
SKIN:- Both sides of the main frame shall be finished with 12mm thk 303
MR grade Commercial Plywood screewed to the frame with joints as
directed upto 3'0" level and from 7'0" level to the top upto false ceiling level
and including 6 mm thk. clear glass Straight / segmented with bevelled
edges including frosted film of approved make & design and drawing to be
fixed with t.w moulding all around of approved size & design including
grooves, mouldings etc complete as directed by Architect & as shown in
the drawing.
SKIRTING : In the same alignment, 3" high in 12mm thk 303 MR grade
Commercial Plywood with a groove finished with laminate / veneer as the
case maybe, or as directed by the Architect.
The rate shall include providing & fixing t.w. beading all throughout the
exposed edges & periphery including fixing the glass with studs, sealing all
the joints, providing grooves in the finish, melamine polish to the mouldings
& t.w members, complete as per the directions of Architect. All Aluminium
sections shall be smooth, rust free, straight, mitred and jointed
mechanically.
The finishes for the skinning to be screwed to the framework on both the
sides as duly mentioned above shall comprise of the following types: -
Sinature and Seal of the bidder Page5
SHETGIRI and ASSOCIATES
A Both side skins to be finished with 3.0 mm thk approved quality veneer
finished with high-end melamine polish as shown in drawing or as directed
by Architect.
120 Sq. Mts
B One side skin to be finished with 1.5mm thk approved laminate & other
side skin with 3.0 mm thk approved quality veneer finished with high-end
melamine polish as shown in drawing or as directed by Architect.
9.29 Sq. Mts
3 (i) Providing & Fixing Low height Partition as per specifications including
skirting, complete as per the design requirements mentioned above,
drawings and instructions in all respects with an height of 4'-0" to 4'-6" to
be erected in 2" X 2" Aluminium section of 16 Gauge verticals not
exceeding 1' 6" to 2' 0" centres and 2" X 1" size Aluminium sections
horizontal at floor level / skirting ht, intermediate level & 3'-0" level with
12mm. Providing & Fixing, 303 MR grade Commercial Plywood skin on
both sides of the frame to be screewed to the frame with joints as directed
upto a height of 3'-0" to 3'-6" including 5.5mm thk glass with bevelled edges
of 1'0" to 1'6" height, including approved frosted film of approved make &
design on the glass including soft board panel with felt cloth.
326 Sq. Mts
The plywood skin to be finished with 3.0 mm thk. approved veneer with
melamine polish with t.w. beading all throughout the exposed edges &
periphery including fixing the glass with studs, sealing all the joints, grooves
in the finishes, melamine polish to the mouldings & t.w members, complete
as per the directions of Architect. All Aluminium sections shall be smooth,
rust free, straight, mitred and jointed mechanically.
All works shall be carried out as per Architectural drawings and the
directions of Engineer-in-charge. Both sides of the partition finished with
3.0 mm thk approved high end premium quality veneer, finished with high
end melamine polish of approved grade as per the drawing including
designed grooves etc complete.
3 (ii) Providing & Fixing Low height Partition as per specifications including
skirting, complete as per the design requirements mentioned above,
drawings and instructions in all respects with an height of 4'-0" to 4'-6" to
be erected in 2" X 2" Aluminium section of 16 Gauge verticals not
exceeding 1' 6" to 2' 0" centres and 2" X 1" size Aluminium sections
horizontal at floor level / skirting ht, intermediate level & 3'-0" level with
12mm. Providing & Fixing, 303 MR grade Commercial Plywood skin on
both sides of the frame to be screewed to the frame with joints as directed
upto a height of 3'-0" to 3'-6" including 5.5mm thk glass with bevelled edges
of 1'0" to 1'6" height, including approved frosted film of approved make &
design on the glass including soft board panel with felt cloth.
2.78 Sq. Mts
The plywood skin to be finished with 1.5 mm thk. approved laminate with
t.w. beading all throughout the exposed edges & periphery including fixing
the glass with studs, sealing all the joints, grooves in the finishes, melamine
polish to the mouldings & t.w members, complete as per the directions of
Architect. All Aluminium sections shall be smooth, rust free, straight, mitred
and jointed mechanically.
All works shall be carried out as per Architectural drawings and the
directions of Engineer-in-charge. Both sides of the partition finished with
1.5 mm thk approved high end premium quality laminate as per the drawing
including designed grooves etc complete.
Sinature and Seal of the bidder Page6
SHETGIRI and ASSOCIATES
4 Full Height Fully Glazed partition
A Providing and erecting in position full height fully glazed partiton in 12mm
thk. toughened glass fixed within floor channel to be embedded within the
floor finish including Patch fittings, providing and fixing frosted film of
approved make, shade & design on the glass. AlI damages to the floor
work to be reinstated without any extra cost including the cost of other
fittings & fixtures, hardware such as spider fittings for glass to glass
connections for longer spans etc complete, necessary holes, including
joints between glasses, floor & supports to be sealed with silicone sealant
on all sides complete in all respects etc as per directions of Architect. The
rate shall be inclusive of bent curved glass panels wherever the partition is
curved in profile as shown in the layout plan.
300 Sq. Mts
B Providing and erecting in position full height fully glazed partiton in 12mm
thk. design decorative coloured toughened glassfixed within floor channel
to be embedded within the floor finish including Patch fittings, providing and
fixing frosted film of approved make, shade & design on the glass. AlI
damages to the floor work to be reinstated without any extra cost including
the cost of other fittings & fixtures, hardware such as spider fittings for
glass to glass connections for longer spans etc complete, necessary holes,
including joints between glasses, floor & supports to be sealed with silicone
sealant on all sides complete in all respects etc as per directions of
Architect. The rate shall be inclusive of bent curved glass panels wherever
the partition is curved in profile as shown in the layout plan. The basic rate
of Glass = Rs. 480 / Sq Fts plus taxes (GST).
28 Sq. Mts
5 Partitions above False Ceiling
Providing and fixing frame work in 2"x2" Aluminium section of 16 Gauge
verticals, not exceed 1' 6"-2'-0" centres and 2" X 1" size Aluminium
sections horizontal wherever directed and finishing with 12 mm thk 303 MR
grade Commercial Plywood on both sides and finishing the same with
approved acryllic emulsion paint including insulating the same with
approved insulating material upto soffit of beam or ceiling including properly
anchoring the same making necessary cut-outs for AC ducts, Services etc
complete wherever directed.
41.80 Sq. Mts
6 PANELLING : -
A (i) Providing and fixing Wall & Column Panelling for the existing surfaces to be
made out of 16 gauge Aluminium framework backing of size 2" X 1" at 1'6"
to 2' c/c bothways to be covered with 12mm thk 303 MR grade Commercial
Plywood and finished with approved 3.0 mm thk Veneer and melamine
polish including skirting & band at top in the same alignment with a groove
and including teakwood moulding of approved size as shown in detailed
drawing or as directed by Architect
418.71 Sq. Mts
A (ii) Providing and fixing Wall & Column Panelling for the existing surfaces to be
made out of 16 gauge Aluminium framework backing of size 2" X 1" at 1'6"
to 2' c/c bothways to be covered with 12mm thk 303 MR grade Commercial
Plywood and finished with premium quality approved 3.0 mm thk Veneer
and high end melamine polish including skirting & band at top in the same
alignment with a groove and including teakwood moulding of approved size
as shown in detailed drawing or as directed by Architect. (Quantity
considered herein under this item shall be a combination of raised and
recessed panels of appropriate dimensions and including 6mm thk
additional plywood backing for the raised panels including designer
moulding at the edge / junction of raised and recessed panels including
high end polish to the moulding matching the polish provided for the panels
etc complete).
69.67 Sq. Mts
Sinature and Seal of the bidder Page7
SHETGIRI and ASSOCIATES
B Providing and fixing Wall & Column Panelling for the existing surfaces to be
made out of 16 gauge Aluminium framework backing of size 2" X 1" at 1'6"
to 2' c/c bothways to be covered with 12mm thk 303 MR grade
Commercial Plywood and finished with approved 1.5mm thk laminate
including skirting & band at top in the same alignment with a groove and
including teakwood moulding of approved size as shown in detailed
drawing or as directed by Architect
52.95 Sq. Mts
C Providing and fixing Wall & Column Panelling for the existing surfaces to be
made out of 16 gauge Aluminium framework backing of size 2" X 1" at 1'6"
to 2' c/c to be covered with 12mm thk 303 MR grade Commercial Plywood
and finished with approved interior grade ACP including skirting & band at
top in the same alignment with a groove and including teakwood moulding
of approved size including the necessary partical board / ply backing to
match the level of other finishes such as veneer in required areas as shown
in detailed drawing or as directed by Architect
90.77 Sq. Mts
D Providing & Fixing designer approved Accoustic Fabric Panelling of
Armstrong, Anutone or equivalent make including approved fabric of
standard width over and 25mm thk glasswool or soft board backing, total
thickness as per manufacturers spcecifications. The NRC to be minimum of
0.9. All around the panelling, decorative teak wood mouldings shall be
provided and shall be finished with melamine polish complete as per the
instructions of Architect.
65.03 Sq. Mts
E Providing and laying in position approved designer translucent cut panels of
approved make and in methacrylate core (Acryllic) bounded by engraved
veneer of size upto 2400 mm X 1200 mm and for any length and height in
standard thickness of 3.8 mm and in any design and colour finish including
making necessary provision for providing LED back-lit lighting on the rear
side of the acryllic core, necessary framework for fixing the arrangement,
brackets, teakwood moulding all around the periphery, necessary
hardware, fittings, fixtures etc complete as per the manufacturers
specifications & directions of Architect. (Basic rate shall be Rs. 700 / Sq.
Fts plus taxes {GST}).
55.74 Sq. Mts
F Providing & Fixing Soft Board panelling over framework of 25 mm x 18 mm
Solid core treated high end wooden Frame at 600 mm c/c with 6mm Marine
ply skining on top & 12mm thk. soft board with fabric finishing over ply.
Complete as per drawings & directions of the Competent Authority, 25 mm
x 12 mm T.W. Moulding on edges (Basic Price of fabric Rs.250/- meter
plus taxes {GST}).
37.16 Sq. Mts
G Providing and laying in position approved 18mm thk high end Onyx Italian
Marble such as Tiger onxy stone or equivalent approved for panelling /
cladding or dado work in required size and pattern as directed including
base mortar with 1:4 white cement mortar (1 cement : 4 coarse sand)
(Brick / Siporex wall with cement plaster shall be paid for seperately under
the relevant items. Only providing & fixing of onyx marble including
additional base mortar if any shall be paid for under this item), pointing,
joints finished in line and level and flushed in matching colour cement,
curing, rubbing, machine mirror grade polishing, washing, cleaning and
sealer for anti-stain of Aqua mix brand etc complete as per the directions of
Architect.
27.87 Sq. Mts
Sinature and Seal of the bidder Page8
SHETGIRI and ASSOCIATES
H Providing and fixing Wall & Column Panelling for the existing surfaces to be
made out of 16 gauge Aluminium framework backing of size 2" X 1" at 1'6"
to 2' c/c bothways to be directly finished with skin in 12 mm thk approved
Gypsum Board to be screewed directly to the Aluminium framing including
POP Punning, levelling etc complete. The finishes for the said item shall
comprise of the following: -
i Providing & Fixing Acryllic Emulsion Paint finish to the skin in coats of
desired number 46.45 Sq. Mts
ii Providing & Fixing Textured Paint finish finish to the skin 27.87 Sq. Mts
iii Providing & fixing approved wallpaper over the skin surface (Basic rate of
Rs. 200/ Sq. Fts plus taxes {GST})
55.74Sq. Mts
I Providing & Fixing Mirror Panelling using 6 mm thick mirror of approved
make over 19mm 710 BWP grade Marine Plywood backing. The mirror to
be fixed with T.W beading of size 12.5mm X 19mm, finished with melamine
polish complete as per the instructions of EIC. The rate shall be inclusive of
providing & fixing S.S studs of appropriate size & diameter as directed
including bevelling for the mirror
46.45 Sq. Mts
J Providing and laying in position approved designer cut panels or
standalone partition seperators of approved make and in ABS material
(toughened plastic) of size 300 mm X 300 mm interlocking arrangement for
any length and height in thickness upto 25 mm and in any designs and
body and cover colour finish such as jali, matrix, aura etc including
providing and fixing 12 mm thk frosted glass on the rear side of the panel
as backing material including provision for providing LED back-lit lighting on
the rear side, necessary framework for fixing the arrangement, brackets for
fixing glass, teakwood moulding all around the periphery, necessary
hardware, fittings, fixtures etc complete as per the manufacturers
specifications & directions of Architect. (Basic rate shall be Rs. 1700 / Sq.
Fts plus taxes {GST})
13.93 Sq. Mts
K Providing and fixing Wall & Column Panelling for the existing surfaces to be
made out of 16 gauge Aluminium framework backing of size 2" X 1" at 1' 6"
to 2' 0" c/c to be covered with 12mm thk 303 MR grade Commercial
Plywood backing and finished with 4mm designer, decorative MDF board
including coats of duco paint of approved shade, colour & texture including
teakwood moulding of 4mm size all around the periphery as directed by
Architect
122.00 Sq. Mts
L Providing & Fixing 6mm thk Corian for Partitions, panelling, False
Ceiling, Tables, Furniture etc as per directions for the existing raw
surfaces such as plywood, partical board, MDF, Aluminium framework etc
including finishing the corian with polish of approved shade, colour &
texture, frame etc complete as directed by Architect
60.00 Sq. Mts
L Providing and fixing Accoustical Board Panelling for the existing surfaces to
be made out of 16 gauge Aluminium framework backing of size 2" X 1" at 1'
6" to 2' 0" c/c to be covered with 19 mm thk fine fissured high accoustic tile
board with a minimum NRC of 0.95, Class I (Class A) fire rating etc
complete. The accoustical board shall resemble wooden veneer panels &
shall have matching wooden veneered finish.
63.17 Sq. Mts
M Providing and fixing back-painted 6 mm thk colored glass to be provided for
any type of Partitions, Panelling, False Ceiling, Tables, Furniture etc as per
directions for the existing raw surfaces such as plywood, partical board,
MDF, Aluminium framework etc directly to be mounted over the surface or
over and including SS studs including making provision for providing LED
cove backlit lighting wherever directed, brackets, necessary hardware,
fittings, fixtures etc complete as per the directions of Architect. Basic rate
for back painted glass / muralic glass shall be Rs. 300 / Sq. Fts.
30 Sq. Mts
Sinature and Seal of the bidder Page9
SHETGIRI and ASSOCIATES
7 Flush door
Providing and fixing 38mm thk water-proof ready made heavy duty solid
flush doors for Toilets, cabins, ancillary areas specified to match the solid
partitions finish including designer inlays & raised and recessed panels in
3.0 mm thk veneer with high end melamine polish including 2nd class BTC
frame of 100 X 50mm to be finished with 3.0mm thk approved veneer with
high end melamine polish finish for all exposed surfaces including heavy
duty floor springs, approved locks, 450 mm long SS long handles, 4 Nos of
hinges, cylindrical lock, knobs etc. complete as per the directions of
Architect.
88.25 Sq. Mts
8 Box for Rolling shutter
Providing and erecting boxing to cover the rolling shutter to be made out of
19mm thk. 303 MR grade Commercial Plywood for casing and openable
shutters below for servicing to be finished with approved 4.0 mm thk
exterior grade ACP including hardware such as hinges, locks etc.complete
as per instructions of Architect.
32.51 Sq. Mts
9 Rolling Shutter
a Providing and fixing new opaque rolling shutter with top box, channels,
locks, sliders etc complete as per site conditions. 35.30 Sq. Mts
b Removing & refixing the existing rolling shutter, repairing the same,
replacing the damaged sliders, channels etc including painting with 2 coats
of enamel paint etc complete.
35.30 Sq. Mts
10 MAIN DOOR :
Providing & Errecting in position Fully glazed double leaf door & its side
fixed glass in 12 mm thk Toughened Glass on Patch fittings of the size 3'0"
X 7'0" each including top patch fitting, bottom patch fitting, patch lock, Floor
Spring of reputed manufacturer and S.S handle 600mm long, 30mm dia
including frosted film of approved make, shade & design on the glass. AlI
damages to the floor work to be reinstated without any extra cost including
the cost of other fittings & fixtures & necessary hardware, necessary holes,
joints to be sealed with silicone sealant complete in all respects etc as per
drawings and directions of Architect.
Size: 3'0" X 7'0" for each of the door 55.74 Sq. Mts
11 FALSE CEILING
General :
The filler, paper tapes, finishes and primers suitable for Gypsum boards,
shall be as per recommended practises of India Gypsum.
Framework grid and suspenders shall be fixed to avoid fouling with
services such as ducting, sprinklers, electricals fixtures, etc
T.W. framing may be allowed in certain areas for the Gypsum Board ceiling
with the approval of the Architect. The same should have three coats of fire
resistant paint.
Note: All the hardware such as fastners, hangers, suspenders, etc.
required for erection of the false ceiling shall be of standard approved make
& manufacturers specifications and approved by the Architect.
Sinature and Seal of the bidder Page10
SHETGIRI and ASSOCIATES
A Metal frame False Ceiling of 12 mm thk. Gypsum Board including vertical
drop panels.278.79 Sq. Mts
Providing and Fixing 12 mm Thk. Gypsum board on metallic grid,
conforming to IS: 2095: :1982. The metallic grid shall consists of the
following :
Gl Perimeter channels of size 27mm and 0.5mm thk. having one flange of
20mm and another flange of 30mm.
Gl intermediate channel of size 45mm 0.5mm thk. With two flange of 15mm
each at 4'-0" centre to centre.
Gl Hanger of size 1"x1", 0.5mm thk. A 4'-0" centre to centre distance.
Gl Cleat and Steel Expansion Fasteners.
Ceiling section of 0.5mm thickness having curled wedge of 51.5 mm and
two flanges of 26mm each with lips of 10.5mm at 450mm center to center.
Connecting clips & 12.5 mm dry wall screws at 230 mm center to center.
The metallic grid shall be installed as follows :
The perimeter channel along the perimeter of the ceiling with screw fixed to
brickwall / partition with the help of rawlplugs and screws.
The intermediate channels shall be suspended from the ceiling with steel
Gl hanger fixed to the slab soffit with Gl cleat and steel expanation
fasteners.The intermediate channels shall be at 4'-0" centre to centre
distance.
The ceiling section placed in a direction perpendicular to the intermediate
channel at 1'-6" C/C distance shall be fixed to the intermediate channel with
the help of connecting clips and 12.5 mm dry wall screws at 230 mm centre
to centre distance.
Finally, the 12mm thk. Gypsum boards shall be fixed to the metal frames
and the tapered/square edges of the boards shall be finished to a flush joint
with requisite filler, paper tapes, finisher and primer suitable for Gypsum
plaster boards, (as per recommendations of manufacturers, Indian Gypsum
or equivalent) including Acrylic Emulsion Paint of approved make and
shade and colour.
The rate shall include the cut-outs to be made for light fittings, grills,
diffusers, speakers, smoke detectors, sprinklers etc. with provision of the
frame along perimeter of the cut outs/ opening with channels/ ply to support
the ceiling adequately as per the directions of Architect. The rate shall
include necessary shapes, designs, patterns in curvature, sloping, dome,
oval & eliptical shaped etc including the necessary provisions of coved
lighting scheme etc complete as per the designs, drawings and instructions
of the Architect.
B Mineral Fibre Board False Ceiling
Providing and erecting false ceiling of Mineral Fiber ceiling Board of
approved make with framework, runners, cross runners & suspenders from
the existing ceiling as per the manufacturers details and specification and
600X 600mmX 15mm thk tiles of approved design, texture & in microlook
pattern including the grids in black / white silhoutte pattern, 15mm as per
manufacturers specifications complete including making necessary cut-outs
for electrical fixtures, AC diffusers, access etc as per the instructions of the
Architect.
185.80 Sq. Mts
Approved preminum Tile in Dune RH Microlook or equivalent approved
category with black silhouette locking supporting system, 15 mm grid.
Sinature and Seal of the bidder Page11
SHETGIRI and ASSOCIATES
C Providing and erecting false ceiling in veneer in any shape, design, pattern
such as curvature, sloping, dome, oval, suspended dome, cylinder, inverted
dome, eliptical shaped, battens & any other shape as directed or instructed
etc including the necessary provisions of coved lighting arrangement etc
complete as per the designs, drawings and instructions of the Architect to
be provided with 12 mm thk Commercial ply backing on teak wood frame to
be anchored to the main ceiling with cross runners tongued and grooved
including anchor fasteners, cross bracings, brackets etc. Ply to be fixed to
the teakwood frame to be finished with approved 3.0 mm thk high end
premium class veneer & high end melamine polish etc complete as per
directions of the Architect.
37.16 Sq. Mts
D Providing and erecting false ceiling in ACP with 12 mm thk MR grade
Commercial plywood backing on teak wood frame to be anchored to the
main ceiling with cross runners tongued and grooved. The ply to be finished
with approved 2mm thk interior grade ACP complete as per directions of
the Architect.
13.93 Sq. Mts
12 Providing & Applying Plaster of Paris Punning up to average thickness of
12 mm thk. on existing walls to proper level & plumb, including Groove
Complete as per site conditions & directions of the Architect.111.57 Sq. Mts
13 Providing and erecting in position Plaster of Paris Cornices 3" x 3" in size to
the false ceiling. Including filling the gaps with POP & painting the same
with Acryllic Emulsion paint of approved colour and texture as per
instruction of Architect.
137.19 Rmt.
14 STAIN GLASS CEILING:
Providing & errecting in position 10 mm thick stained glass in the ceiling
with 50x50 mm second class teak wood frame to be anchored to the main
ceiling with cross runners tongued & grooved in approved manner, polished
with melamine polish and shall be suspended with hangers to take the
load of complete system etc. complete.
4.64 Sq. Mts
15 (i) Providing & Fixing high end & premim class Roller Blinds of approved
make with supporting framework etc of approved shade & colour, opaque
eclipse type complete in all respects & working order with triple spring
arrangement as per manufacturers specifications & standards & directions
of the Competent Authority. (Basic rate of Roller Blinds shall be Rs. 120 /
Sq. Fts plus taxes {GST})
353.95 Sq. Mts
15(ii) Providing & Fixing Vertical Venetian Blinds 4" wide of' approved make,
shade, texture in two colours with supporting framework and assembly
complete in all respects & working order with triple spring arrangement as
per manufacturers specifications & standards & directions of the
Competent Authority.
43.66 Sq. Mts
16 (i) Providing and fixing Full height Storage of ht. 7'-0" and depth as specified
in the drawings as per specification below.
Skeleton - made out of 19 mm. thk 303 MR grade Commercial Plywood at
end verticals, top and bottom and verticals 450mm to 600mm Centres as
shown in drawing and 6 mm thk back marine ply.
SHELVES - 19mm Thk. 303 MR grade Commercial Plywood top and
edges finished in 0.8mm thk. Laminate to accommodate file height
removable and supported on pins.
SHUTTERS-made out of 19mm thk. 303 MR grade Commercial Plywood
externally finished in 3.0mm thk. Veneer with melamine polish and
Internally finished in 0.8 mm thk. Laminate as shown or directed.
Sinature and Seal of the bidder Page12
SHETGIRI and ASSOCIATES
HINGES - Each shutter shall have 100mm long oxidised brass butt hinges.
Mimimum 4 nos. hinges for each of the shutter for Full height Storage and
3 Nos. hinges for each of the shutter for Low Height Storage to be
provided.
BOLTS - Flush tower bolts from inside at top and bottom to the shutters
and magnetic catch fixed top and bottom.
LOCKS - of approved make 4 -lever brass body dead lock with S.S. Key.
HANDLES - 100mm wide handles of c.p. brass as approved by the
Architect.
SKIRTING -As instructed by Architect, in 303 grade commercial plywood
finished in Laminate.
BACK - Back side of storage to have 6mm thk. ply with polish finish.
Finishing :- All external surface finish with 3.0 mm thk approved veneer
with melamine polish. All the exposed woodsurfaces shall be finished in
melamine polish. In side visible surface complete with 0.8mm thk Laminate.
Top to have tw moulding as instructed. All internal wood-work to have coat
of anti termite of approved make before polishing.
13.93 Sq. Mts
16 (ii) Providing & Fixing full height display storage unit with 12mm thk glass
shelves and glass shutters wherever directed on heavy duty magnetic
catch including provision for warm lighting arrangement to be made inside
at the storage top panel. All exposed surfaces to be finished with 3.0 mm
thk high end veneer with melamine polish etc complete and internal
exposed surfaces shall be finished with 3.0mm thk approved high end
veneer with melamine polish including heavy duty hardware, fittings,
fixtures etc complete to the complete satisfaction of the Engineer in charge
& Architect.
6 Sq. Mts
16 (iii)Finishing: - Do - Same specifications as for Full Height Storage units
however for the Locker units of the staff including pigeon holes and the
front of the pigeon holes to be provided with 25mm pre-laminated ply
including locks, hinges, handles, necessary fittings and internally surfaces
to be polished etc complete.
5.43 Sq. Mts
17 Aluminium Louvered Window
Providing and fixing powder coated aluminium louvered window with
5.5mm thk tinted glass and louvered glass panes in aluminium window
sections with proper locking arrangement, heavy duty channels for smooth
movements including provision for fixing of exhaust fan by providing fixed
glass in alumnium section above including approved sun control film etc.
complete as per instructions of Architect.
9.47 Sq. Mts
18 Cabin Door
a Providing and fixing Cabin Entrance Door with thickness matching the
partition thickness (3"), adjoining the same, in solid core door including
necessary solid frame inside, finishing in 4mm thk approved veneer with
high end melamine polish finish for all exposed surfaces. The rate to
include 12mm thk bevelled glass panels (square panels or rectangular from
top to bottom) provided within the door including beading of appropriate
size to be finished with melamine polish, frosted film of approved make etc
complete. including heavy duty floor springs, approved locks, 450 mm long
30mm dia SS long handles, cylindrical lock, knobs etc. complete as per the
directions of Engineer in charge & Architect. Please Note that the shape &
size of glass-solid combination such as "S", rectangular etc shall vest with
Engineer in charge & Architect.
54.98 Sq. Mts
Sinature and Seal of the bidder Page13
SHETGIRI and ASSOCIATES
b Providing & Errecting in position Fully glazed single / double leaf door in 12
mm thk Toughened Glass on Patch fittings including top patch fitting,
bottom patch fitting, patch lock, Floor Spring of reputed manufacturer and
SS handle 450mm long, 30mm dia including frosted film of approved make,
shade & design on the glass. AlI damages to the floor work to be reinstated
without any extra cost including the cost of other fittings & fixtures &
necessary hardware, necessary holes, joints to be sealed with silicone
sealant complete in all respects etc as per drawings and directions of
Architect.
112.00 Sq. Mts
SUM TOTAL OF SCHEDULE - INTERIOR FIXED ASSETS WORKSRs.
Please Note : The rates quoted hereinabove shall be Exclusive of GST
and GST shall be additional at actuals.
SEAL AND SIGN OF BIDDER
Sinature and Seal of the bidder Page14
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate (Rs.) Amount (Rs.)
3. SCHEDULE - FURNITURE WORKS
N.B: - The plywood considered in this estimate shall be IS 303 MR grade
Commercial Plywood for all the items of Interior & Furniture works. The
rate shall be inclusive of anti termite coating on all sides to plywood, teak
wood & all the other wooden components of Asian paints or equivalent
approved make.
1 Providing and fixing Low height Storage of ht. 2'-6" or 4'-0" as desired
and depth of 16" or 18" as specified in the drawings as per specification
below.
Skeleton - made out of 19 mm thk plywood at end verticals, top and
bottom and verticals 450mm to 600mm Centres as shown in drawing and 6
mm thk back ply.
SHELVES - 19mm Thk. Plywood top and edges finished in 0.8mm thk.
Laminate to accommodate file height removable and supported on pins.
SHUTTERS-made out of 19mm thk. ply externally finished in 3.0mm thk.
Veneer with polycoat polish and Internally finished in 0.8 mm thk. Laminate
as shown or directed.
HINGES - Each shutter shall have 100mm long oxidised brass butt hinges.
Mimimum 4 nos. hinges for each of the shutter for Full height Storage and
3 Nos. hinges for each of the shutter for Low Height Storage to be
provided.
BOLTS - Flush tower bolts from inside at top and bottom to the shutters
and magnetic catch fixed top and bottom.
LOCKS - of approved make 4 -lever brass body dead lock with S.S. Key.
HANDLES - 100mm wide handles of brass as approved by the Architect.
SKIRTING -As instructed by Architect, in plywood finished in approved 3.0
mm thk veneer with polycoat polish.
BACK - Back side of storage to have 6mm thk. MR grade commercial ply
with polish finish.
The finishes for the Low height storage unit as duly mentioned above shall
comprise of the following types: -
a Providing & Fixing for all the external surfaces and exposed woodsurfaces
including the top shall be finished with 3.0 mm thk high end veneer with
melamine polish. Inside visible surfaces complete with 0.8mm thk
Laminate. Top to have t.w. moulding finished with high end melamine
polish as instructed.
90 Sq. Mts
b Providing & Fixing for all the external surfaces including the top of the
storage unit and exposed woodsurfaces shall be finished with 3.0 mm
approved veneer with polycoat polish. Inside visible surfaces complete
with 0.8mm thk Laminate. Top to have t.w. moulding finished with high end
polycoat polish as instructed.
33.09 Sq. Mts
c Providing & Fixing for all the external surfaces and exposed woodsurfaces
shall be finished with 3.0 mm approved veneer with melamine polish
except the top of the storage unit which shall have 3.0mm thk high end
veneer with polycoat polish. Inside visible surfaces complete with 0.8mm
thk Laminate. Top to have t.w. moulding finished with high end polycoat
polish as instructed.
48.30 Sq. Mts
d Extra rate over and above the rates for items A & B above, but for
providing and fixing wherever instructed & directed above the 2'-6" or 4'-0"
high storage units, 18mm thk approved raw silk or equivalent approved
granite including edge moulding as shown in the plan and directed by the
Consultant etc complete.
18.39 Sq. Mts
INTERIOR RENOVATION WORK OF NABARD REGIONAL OFFICE AT 54, WELLESLEY ROAD, P.B.NO. 5, SHIVAJI NAGAR,
PUNE-411005
Sinature and Seal of the bidder Page15
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate (Rs.) Amount (Rs.)
e Providing & Fixing Overhead storage of 2'-0" height and length as desired
above the Pantry counters to be finished with approved 1.0 mm thk high
gloss laminate finish in vibrant colors or glossed natural wooden textured
laminates for all exposed surfaces.
11.14 Sq. Mts
Skeleton - made out of 19 mm thk plywood at end verticals, top and
bottom and verticals 450mm to 600mm Centres as shown in drawing and 6
mm thk back ply. Provision for kitchen hoods / chimney shall be provided
without any supporting skeleton frame for the chimney portion
SHELVES - 19mm Thk. Plywood top and edges finished in 0.8mm thk.
Laminate to accommodate file height removable and supported on pins.
Provision for kitchen hoods / chimney shall be provided without any
shelves for the chimney portion
SHUTTERS-made out of 19mm thk. ply externally finished in 3.0mm thk.
Veneer with polycoat polish and Internally finished in approved 1.0 mm thk
high gloss laminate finish in vibrant colors or glossed natural wooden
textured laminates for all exposed surfaces as directed. The chimney
portion shall not be provided with any shutter enclosure
HINGES - Each shutter shall have 100mm long oxidised brass butt hinges.
Mimimum 4 nos. hinges for each of the shutter for Full height Storage and
3 Nos. hinges for each of the shutter for Low Height Storage to be
provided.
BOLTS - Flush tower bolts from inside at top and bottom to the shutters
and magnetic catch fixed top and bottom.
LOCKS / MAGNETIC BALL CATCH to be provided of approved make
HANDLES - 100mm wide handles of brass as approved by the Architect.
BACK - Back side of storage to have 6mm thk. MR grade commercial ply
with polish finish.
2 Providing and erecting in position Side Credenza unit for the tables of
750mm height and 450mm deep or as instructed by the Architect to be
made out of 19mm thk 303 MR grade Commercial plywood & having t.w.
moulding all round with 2 nos of drawers on top and openable shutters
below. The openable shutters to be made out of 19mm thk. ply with all
internal surfaces to be finished in 0.8 mm thk approved laminate and
externally with 3.0mm thk approved veneer with melamine polish except
the top, which shall have 3.0mm thk approved veneer with polycoat polish
including brass hinges, ball catches, 100mm brass handles, brass locks
etc. complete as per the instruction of the Architect.
a Providing & Fixing for all the external surfaces and exposed woodsurfaces
including the top shall be finished with 3.0 mm thk high end veneer with
melamine polish. Inside visible surfaces complete with 0.8mm thk
Laminate. Top to have t.w. moulding finished with high end polycoat polish
as instructed.
47.84 Sq. Mts
b Providing & Fixing for all the external surfaces and exposed woodsurfaces
shall be finished with 3.0 mm approved veneer with melamine polish
except the top of the storage unit which shall have 3.0mm thk high end
veneer with polycoat polish. Inside visible surfaces complete with 0.8mm
thk Laminate. Top to have t.w. moulding finished with high end polycoat
polish as instructed.
12.00 Sq. Mts
c Providing & Fixing for all the external surfaces including the top of the
storage unit and exposed woodsurfaces shall be finished with 3.0 mm
approved veneer with polycoat polish. Inside visible surfaces complete
with 0.8mm thk Laminate. Top to have t.w. moulding finished with high end
polycoat polish as instructed.
3 Sq. Mts
Sinature and Seal of the bidder Page16
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate (Rs.) Amount (Rs.)
3 Providing and errecting in position Meeting table to be made out of 19mm
thk Plywood top with 60 X 60mm thk t.w.moulding all round the top to be
finished with approved 3.0 mm thk high end veneer including approved
polycoat polish, and to be errected on a framing of t.w 75 X 75 mm thk
moulded frame vertical, horizontal at top & bottom & including bracings at
a regular interval of 900 mm centres, which shall have 19mm thk ply on
both sides to be finished with approved 3.0 mm thk veneer with melamine
polish. All the exposed middle verticals & framing (aprons) shall be
finished with 19mm thk plywood and approved 3.0 mm thk natural veneer
with melamine polish as per the drawings & instructions of the Architect.
The rate shall be inclusive of necessary cut outs & provisions for video/tele
conferencing, wire managers, necessary hardware, cable cubby, cabling
arrangements for video / tele conferencing, openings for speakers
including cut outs in the top to be filled with planters & white pebbles &
12mm thk toughened glass on t.w moulding support in the cut out area etc
complete including cabling arrangements for video / tele conferencing,
openings for speakers etc complete. The rate shall also include providing
foot rest fixed to the central core support section of the table of projection
width as directed to be finished with approved veneer with melamine polish
etc complete.
The rate shall be inclusive of making provisions for AV controls, Electrical
installations, gadgets etc. The rate shall also include the provisions for
making the table moveable including providing & fixing heavy duty castors,
locking arrangements for the castors etc complete. The rate shall also
include provisions for video / tele conferencing, wire managers if any,
necessary hardware, cable cubby if directed, cabling arrangements for
video / tele conferencing equipments, openings for speakers etc all
complete at the complete satisfaction of the Architects & Clients.
a Size of Table - 6'-6" X 42'-6" with specifications as above. 1.00 No
b Size of Table - 8'-2" X 16'-6" with specifications as above. 1.00 No
c Size of Table - 14'-3" X 4'-5" with specifications as above. 1.00 No
d Size of Table - 14'-3" X 3'-6" with specifications as above. 2.00 No
e Circular table with the diameter of the table to be 10'-9" with specifications
as above
1.00 No
Sinature and Seal of the bidder Page17
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate (Rs.) Amount (Rs.)
4 EXECUTIVE DINING TABLE / MULTI-PURPOSE TABLE
Providing and errecting in position Executive Dining / multi-purpose Table
to be made out of 19mm thk 303 MR grade Commercial plywood top with
60 X 60mm thk t.w.moulding all round the top to be finished with approved
3.0 mm thk high end veneer with polycoat polish and to be errected on a
framing of t.w 75 X 75 mm thk moulded frame vertical, horizontal at top &
bottom & including bracings at a regular interval of 750 mm centres, which
shall be covered with 19mm thk ply to be finished with approved 3.0 mm
thk high end veneer with high end melamine polish. All the exposed middle
verticals & framing (aprons) shall be finished with 19mm thk plywood and
approved 3.0 mm thk veneer with high end melamine polish as per the
instructions of the Architect.
The rate shall be inclusive of necessary openings & cutout in the top of the
table to be filled with planters & white pebbles & 12mm thk toughened
glass on t.w moulding support in the cut out area etc complete. The rate
shall also include providing foot rest fixed to the central core support
section of the table of projection width as directed to be finished with
approved veneer with melamine polish etc complete. Elevation of the table
shall be as directed by Architect on site.
a Size of Table - 7'-4" x 17'-6" 1.00 No
b Size of Table - 7'-0" x 3'-0" 3.00 Nos.
5 Table for The Hon'ble Chief General Manager (C.G.M) / Hon'ble
Managing Director (M.D)
Providing and supplying table for the Hon'ble C.G.M & Hon'ble M.D as
shown in the plan or as approved and effective length of 8'-0" (clear) X 4'-
0" (clear) to be made out of 19mm thk. Plywood finished with approved
3.0mm thk high end & premium class veneer with polycoat polish for the
top. The front & side aprons to have 3.0 mm thk high end and premier
class veneer with high end melamine polish. The top of the table to have
t.w. moulding all around the table to be finished with polycoat polish of
approved shade. The rate shall be inclusive of providing a heavy duty
keyboard tray on sliding telescopic channels & a pedestal drawer unit
made out of 16mm thk marine ply on side with 2 nos of equal sized
drawers on sliding channels & openable shutter below to be finished with
3.0 mm thk high end veneer with high end melamine polish for the external
exposed surfaces. The side credenzas shall be on both the sides & shall
be paid for seperately under the relevant item.
2.00 Nos
All internal surfaces to be finished in approved 0.8mm thk laminate. All the
external exposed surfaces shall be finished with 3.0mm thk approved high
end veneer with melamine polish including the drawer unit except the top
which shall have polycoat polish. The rate shall also include heavy duty
CPU trolley of reputed manufacturer. The necessary hardware such as
automatic locking, ball catches, wire managers etc to be provided as per
the instructions of the Architect. The Elevation of the table shall be as
directed by Architect on site, which shall include design inlays in SS, and
central panel to be finished with combination of muralic arrangement,
seperator jali and square bevelled designer glass panels on SS studs etc
complete.
The rate shall be inclusive of necessary openings & provisions for
video/tele conferencing, wire managers, necessary hardware, cable cubby,
cabling arrangements for video / tele conferencing, openings for speakers,
provisions & cut outs for installation of gadgets etc complete. The rate
shall also include providing stand-alone foot rest to the table of projection
width as directed to be finished with approved veneer with melamine polish
etc complete for the entire length of the table.
Sinature and Seal of the bidder Page18
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate (Rs.) Amount (Rs.)
6 Table for The General Manager (G.M) (7'-0" X 3'-0")
Providing and supplying table for the G.M to be made out of 19mm thk.
marine ply finished with approved 3.0mm thk high end veneer with
polycoat polish for the top & 3.0 mm thk veneer with melamine polish for
all other exposed areas. The top of the table to have t.w. moulding all
around. The rate shall be inclusive of providing a keyboard tray on sliding
telescopic channels & a pedestal drawer unit made out of 16mm thk
marine ply on side with 2 nos of equal sized drawers on sliding channels &
openable shutter below. The side credenza shall be on the other side &
shall be paid for seperately under the relevant item.
4.00 Nos
All internal surfaces to be finished in approved 0.8mm thk laminate. All the
external surfaces shall be finished with 3.0mm thk approved high end
veneer with melamine polish including the drawer unit. The table shall
have 6mm. thk clear glass on top with bevelled edges. The rate shall also
include CPU trolley of reputed manufacturer, keyboard trays as per the
approved makes which shall be heavy duty. The necessary hardware such
as automatic locking, ball catches, wire managers etc. to be provided as
per the instructions of the Architect. The rate shall also include providing
stand-alone foot rest to the table of projection width as directed to be
finished with approved veneer with melamine polish etc complete for the
entire length of the table. The Elevation of the table shall be as directed by
Architect on site.
7 Table for The Deputy General Manager (D.G.M) (6'-0" X 3'-0")
Providing and supplying table for the D.G.M to be made out of 19mm thk.
plywood finished with approved 3.0mm thk high end veneer with polycoat
polish for the top & 3.0 mm thk veneer with melamine polish for all other
exposed areas. The top of the table to have t.w. moulding all around. The
rate shall be inclusive of providing a keyboard tray on sliding telescopic
channels & a pedestal drawer unit made out of 16mm thk marine ply on
side with 2 nos of equal sized drawers on sliding channels & openable
shutter below. The side credenza shall be on the other side & shall be paid
for seperately in the relevant item.
14.00 Nos
All internal surfaces to be finished in approved 0.8mm thk laminate. All the
external surfaces shall be finished with 3.0mm thk approved high end
veneer with melamine polish including the drawer unit. The table shall
have 6mm. thk clear glass on top with bevelled edges. The rate shall also
include CPU trolley of reputed manufacturer, keyboard trays as per the
approved makes which shall be heavy duty. The necessary hardware
such as automatic locking, ball catches, wire managers etc. to be provided
as per the instructions of the Architect. The rate shall also include
providing stand-alone foot rest to the table of projection width as directed
to be finished with approved veneer with melamine polish etc complete for
the entire length of the table. The Elevation of the table shall be as
directed by Architect on site.
8 Providing & Errecting in position, bevelled Glass dividers out of 10mm thk
glass between the two workstations admeasuring approx 2''-3" X 1'-6" to
be placed in position with the D-brackets including bevelled edging of the
glass, etching / frosted film etc complete
82.00 Nos
Sinature and Seal of the bidder Page19
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate (Rs.) Amount (Rs.)
9 Reception Counter
Providing and supplying Reception counter of size 7'-0" in curvature and 2'-
6" height with chamfer edge glass 12mm thk for top on stainless steel
hollow pipes 75mm dia & height below 1'-0". The table below the pipe to
be made out of 19mm thk plywood with front apron to have 19mm thk ply
hollow box to be finished with approved 18mm thk onyx italian marble
including provision of coloured or warm lighting behind the onyx stone for
glowing effect. The top of the table shall be provided with approved 18mm
thk italian marble with a cut out for Monitor cabling and wire manager
including pedestal drawer unit with castors comprising of 3 nos of drawers
on side to be finished with approved 3.0mm thk approved veneer with
melamine polish, CPU trolley of standard make and heavy duty keyboard
tray on sliding channels of standard make including all the necessary
hardware, fittings, fixtures.
1.00 No
All exposed surfaces of the counter shall be finished with approved 18mm
thk italian marble except for the drawer unit which shall be finished with
3.0mm thk veneer with melamine polish & internal surfaces shall be
finished with 0.8mm thk laminate including making the necessary openings
for wires of telephone boards, PC, grooves, mouldings, etc complete. The
rate shall also include providing stand-alone foot rest to the table of
projection width as directed to be finished with approved veneer with
melamine polish etc complete for the entire length of the table.
10 Computer Counter
Providing and erecting communication counter (2'-3") wide to made out of
19mm thk. Commercial ply. The counter to have heavy duty keyboard
trays and with a pedestal drawer unit comprising of 3 nos of equal sized
drawers at equal intervals in 19mm thk Commercial ply including
necessary opening for electrical wiring, sockets, AV controls etc complete.
The top of counter shall be finished with approved 3.0 mm thk veneer to
be finished with polycoat polis and all other external exposed surfaces to
have 3.0mm thk veneer with melamine polish and 0.8 mm thk laminate
internally etc complete as per instructions of the Architect. The rate shall
be inclusive of heavy duty CPU trolleys, footrest, wire manager, provision
for electrical, AV & other assessories, cut outs for switch-sockets etc
complete.
7.01 Rmt.
11 Dining Table
Providing and supplying rectangular dining tables 4'-0" x 3'-0" made out of
10mm thk toughened Glass top with design etching pattern with bevelled
edges. The table to have Stainless steel tripod stand comprising of 3 nos
of 2" dia pipe with cross bracings for the entire height of the table & bottom
box cylinder in approved marble as base supporting section, 2" height etc
complete as per instructions. The rate shall also be inclusive of rubber
supports in between the glass & SS supporting arrangement, fittings,
hardware etc complete
32.00 No.
12 Providing 2'-0" wide lunch counter in ply to be finished with 1.5mm thk
laminate for all the exposed areas including the necessary supports in ply
to be finished with 1.5mm thk laminate including neccesary hardware,
polish for the moulding to be provided for the entire front areas of the
counter & supports, hardware etc complete
3.04 Rmt.
13 Planter Boxes (18" Dia)
Providing and supplying 18" dia planter boxes to be made out of 19mm
thk. ply to be finished with 3.0mm thk veneer with melamine polish
externally & painted from inside including G.I. Tray for the base as per the
drawing and instructions of the Architect etc. complete.
Finished with approved 3.0mm thk veneer with melamine polish35.00 Nos.
Sinature and Seal of the bidder Page20
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate (Rs.) Amount (Rs.)
14 Artificial Plants
a Providing and supplying artificial plants approved by Architect such as
moss and including necessary stand for holding the plants as per the
approved sample.
40.00 Nos.
b Same as above but medium size 35.00 Nos.
15 Providing and supplying metallic containers for Artificial plants of approved
design and make10.00 Nos.
16 Providing and fixing ready made magnetic board with ceramic coating of
approved make as per the instructions, specifications and directions of the
competant authority.
92.90 Sq. Mts
17 ARTEFACTS :
a Providing, Suuplying, Installation, Testing, commissioning and errecting in
position decorative thread fountain of max length 2.0 mts and height 7.0
mts with LED based colour changing lights and with the following
requirements: Basic capping rate for all the said items clubbed together
including taxes, duties etc shall be Rs. 3,00,000 / -.
2.00 Nos.
1 1/2" Dia SS Header line with Nozzle assembly Provision. Body-SS-304
Water Curtain Nozzle (Min 70 Nos or as per manufacturers requirements)
Vacume Nozzle (3 Nos)
2.5mm thk. Nylon tread
Submersible Pump 3 HP (1 Unit)
Programmable color changing LED Based Strip light Color-Programmable
to be installed in ply boxing to be finished with approved ACP finish.
Programmable color changing LED Based Floor mounted light Color-
Programmable to be provided within the bund wall pit and made water
tight.
Filtration system for water recycling & purification.
Electrical Panel with starter, MCB's ammeter, voltmeter, single phasing
preventer, indicating lights, etc, Weather proof body
Controller for above said lights
Necessary plumbing work such as GI piping, GI fitting, Valves, etc.
All the necessary civil works including construction of a minimum of 600
mm high bund wall in 230 mm thk brick work duly plastered and finished
with approved 18 mm thk granite slab of approved colour, texture, shade &
size for vertical & top surfaces including necessary dressing, water
proofing of the pit and including filling the entire area with white & coloured
pebbles & artificial planters of approved height including nosing to the
granite etc complete.
Electrical work such as submersible cabling, conduing, etc. Nothing extra
shall be paid against this item.
bProvision for Artefacts such as water acquarium (1 No) and stain glass
murals (2 Nos) in various areas of the office. The right to select & approve
the artefact shall vest with the clients & consultant. The contractor shall
submit brochures of manufacturer at the time of quoting for this item. The
consultants and clients reserve the right to select the artefact in line with
the standard technical specifications or as envisaged & meeting the
manufacturer's specification standards. Basic capping rate for all the said
items clubbed together including taxes, duties etc shall be Rs. 1,00,000 / -.
1.00 Nos.
Sinature and Seal of the bidder Page21
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate (Rs.) Amount (Rs.)
c Providing & fixing in position high end premium collection paintings /
printed decorative metallic frames / glass paintings to be obtained in
consultation with Consultants / Clients. The rights to select & approve the
paintings shall vest with the clients. The contractor shall submit brochures
of manufacturer at the time of quoting for this item. The consultants and
clients reserve the right to select the paintings in line with the standard
technical specifications or as envisaged & meeting the manufacturer's
specification standards. Basic capping rate for all the said items clubbed
together including taxes, duties etc shall be Rs. 1,00,000 / -.
1.00 Lot
i 6 Frames of size 3'0" x 2'0"
ii 6 Frames of size 2'0" x 2'0"
iii 2 Frames of size 6'0" x 3'0"
18 Communication Counter
Providing and erecting communication counter (2'-3") wide to made out of
19mm thk. Commercial ply. The counter to have heavy duty keyboard
trays and with a pedestal drawer unit comprising of 3 nos of equal sized
drawers at equal intervals in 19mm thk Commercial ply including
necessary opening for electrical wiring, sockets, AV controls etc complete.
The top of counter shall be finished with approved 3.0 mm thk veneer to
be finished with melamine polish including all other external exposed
surfaces to have 3.0mm thk veneer with melamine polish and 0.8 mm thk
laminate internally etc complete as per instructions of the Architect. The
rate shall be inclusive of heavy duty CPU trolleys, footrest, wire manager,
provision for electrical, AV & other assessories, cut outs for switch-sockets
etc complete.
6.09 Rmt.
19 Trap Door
Providing and erecting in position trap door in 12mm thk Commercial
Plywood to house A.C ceiling mounted units to be made out of 2" x 11/2"
t.w. frame with openable shutters in ply with necessary hinges, tower bolts,
locks, painting in white colour including POP punning so as to match the
finish of false ceiling in the adjoining areas etc complete as per the
instructions and design.
11.14 Sq. Mts
20 Sun Control / Designer / Reflective film
Providing and fixing premium quality, reflective designer frosted film of
approved make and shade to be fixed to glasses of all types, windows,
partition glasses, panelled glass surfaces etc complete as instructed by
Architect.
55.74 Sq. Mts
21
Providing and fixing of Fire Resistant "Etching Film" on door / windows /
partition glasses as per approved design, shade and make etc. as per the
drawing and as directed by the Architect.27.87 Sq. Mts
22 NAME PLATE:
Providing Name Plate of size 375 X 150 mm in brass and fixing the same
to the required position. Thickness of plate engraved with brass letters
shall be 3mm.
60.00 Nos
23 PELMETS:
Providing and fixing 5" wide Pelmet with 18mm thk ply including t.w
lippings on all edges of the plywood and finished on both sides etc
complete as per the instructions.
Finished in 3.0mm thk approved veneer with melamine polish on both
sides62.70 Sq. Mts
Sinature and Seal of the bidder Page22
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate (Rs.) Amount (Rs.)
24 NOTICE BOARD:
Providing and Supplying Notice Boards 8 cm deep made out of BTC T.W
framing 8cm X 24mm with 12mm thick Soft Board covered with cloth felt
on 6mm Commercial Ply backing and glass shutters openable on pivot
hinges complete with lock and handle. Size-1.20 m X 60 cm complete as
per the drawings, details & instructions of Architect.
10.00 Nos
25 WHITE BOARD WITH CERAMIC COATING:
Providing and fixing White board with ceramic coating of approved make
complete as per the specifications and directions of the competant
authority.13.93 Sq. Mts
26 PATTA & BANDS:
Providing and fixing 75mm wide Patta on the wall with 12mm thk ply
including 12 mm t.w beading with polishing etc complete as per the
instructions.27.87 Sq. Mts
Finished in 3.0mm thk approved Veneer with melamine polish
27 MURALS:
Providing & Errecting Murals in part Plaster of Paris / Part Wooden
sections and decorative materials artwork etc complete as per the detail
provided by the Architect. The rights to select & approve the sofas &
seating shall vest with the clients. The contractor shall submit brochures of
manufacturer at the time of quoting for this item etc complete as per
layout. The consultants reserve the right to select the sofas in line with the
technical specifications envisaged & meeting the minimum specifications
standards.
1.00 Nos
28 KEY HIVE:
Providing & Fixing Key hive of size 600 X 900mm made out of 12mm thk
Commercial ply backing with openable type shutter to be made out of 19 X
75mm outer frame with 6mm thk glass. All exposed surfaces to be finished
with 3.0mm thk approved veneer with high end & high gloss melamine
polish and all internal surfaces to be finished with 0.8mm thk approved
laminate including 75mm handle, 2 nos of 75mm hinges for the shutter,
locks etc complete as per the drawing.
5.00 Nos
29 Compactors
Providing and Errecting in position Compactors of approved make in fixed
double faced storage spaces with feather touch mobility in metallic
fabrication, storage cabinets mounted on white metal monorail with 6
levers centralized locking mechanism in single key locking arrangement.
The fabrication should have rust preventive treatment with oven baked
enamel paint finish including heavy duty grip handwheel with standard
shelves lateral & vertical including mannual and latch locking handles with
end stoppers, safety device preventing accidental closure including all
fittings, locking, fixtures, hardware etc complete. The contractor to submit
the brochure of the manufacturing company before quoting. The item
would be measured as Running Length X Height of the entire assembly of
all the cumulative units.
55.74 Sq. Mts
30 Signage
i
Providing signage boards of total height of minimum of 12" comprising of
desired numbers of alphabets / characters in SS of desired heights,
indicating the various departments of the office on Stainless Steel sheets
and fixing the same at the required location etc complete. (1 No of signage
board comprising any number of alphabets / characters shall be
considered for the purpose of making payment)
15.00 Nos
Sinature and Seal of the bidder Page23
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate (Rs.) Amount (Rs.)
ii
Providing signage board with Logo in the entrance lobby area comprising
of total height of minimum of 36" with text "Welcome to NABARD &
........................." in two languages including Logo and comprising of
desired numbers of alphabets / characters in SS and of desired heights,
fixed over Stainless Steel sheet plate and fixing the same at the required
location etc complete. (1 No of signage board comprising any number of
alphabets / characters shall be considered for the purpose of making
payment)
1.00 Nos
iii
Providing signage board of NABARD with Length of minimum 12'-0" and
Height of minimum 7'-0" Logo over the Entrance foyer / Canopy & at the
terrace level in maximum of three languages including Logo and
comprising of desired numbers of alphabets / characters in Translucent
acryllic board with LED back-lit including necessary provisions for
Electrical cabling, wiring, supply & fixing of LED lights of approved color
and fixing the board using M.S supporting framework of appropriate size,
thickness, gauge and applying a cost of primer and three coats of
approved epoxy paint of approved color etc complete including working at
all levels, heights and fixing the board at the required location etc complete
to the complete satisfaction of Architect / Engineer in charge
4.00 Nos
iii
Providing signage board of NABARD with Length of minimum 12'-0" and
Height of 4'-0" Logo over the Entrance foyer / Canopy & at the terrace
level in maximum of three languages including Logo and comprising of
desired numbers of alphabets / characters in Translucent acryllic board
with LED back-lit including necessary provisions for Electrical cabling,
wiring, supply & fixing of LED lights of approved color and fixing the board
using M.S supporting framework of appropriate size, thickness, gauge and
applying a cost of primer and three coats of approved epoxy paint of
approved color etc complete including working at all levels, heights and
fixing the board at the required location etc complete to the complete
satisfaction of Architect / Engineer in charge
1.00 Nos
SUM TOTAL OF SCHEDULE - FURNITURE WORKS Rs.
Please Note : The rates quoted hereinabove shall be Exclusive of
GST and GST shall be additional at actuals.
SEAL AND SIGN OF BIDDER
Sinature and Seal of the bidder Page24
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate(Rs.) Amount (Rs.)
4. SCHEDULE - MODULAR LOOSE FURNITURE WORKS
1 Assistant General Manager (A.G.M.) Table 46 Nos
Table top Supply and installation of AGM workstations as per layout where MAIN TABLE Size is
1500(L)x750(D) & Height 750mm + Pedestal unit + metal keyboard tray 19" with mouse
pad + Metal CPU Trolley . Made of 25mm thick prelaminated particle board of approved
shade confirming to E1 norms. All the edges of workstation surface shall be provided
with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free
from any VOC.
Storages
SIDE RETURN UNIT:- 1050 (w) x 450 (D) x 750 (H) : completely made up of MDF board
conforming to IS : 12823 Interior Grade with PVC edge banding. Top is in 25mm thk board
with 2mm post formation on 2 sides and 2mm PVC edge banding supported on 25mm thk.
Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge
banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for
mounting switches on the wall adjoining the tables shall be made by customer as the
tables do not come with switch mounting facility.
FRAMES:- ( NEO - 50 mm, 1200 HT )• The frame verticals are made out of 1.5 mm thick CRCA sheets confirming to IS – 513.
• The horizontal members are fabricated with welded joints to the vertical which makes the
frames sturdy and facilitates carriage of cables at different levels.
• All the frames are fitted with M10 leveling bolts to adjust to ground undulations. Can be
adjusted +/- 20 mm.
• Frames can be provided with anchoring arrangement if required.
• All the Frames are duly powder coated in charcoal black colour to a thickness of 50-60
microns confirming to ASTMB – 117, ISO – 1520 and ISO – 1518 & ASTMD - 2794.
• The frame has various slots at different heights for fixing of tabletop brackets, tiles and
shelves.
• The Frames can be attached to form a 2-way, 3-way or a 4-way configuration by means
of connecting posts.
• All frames are fixed with aluminum trims confirming to IS – 733. These trims are finished
in an epoxy powder coating finish.
• The connectors to the frames are made out of ABS plastic of a matching colour to the
trims confirming to ASM standards.
TILES:• Fabric Tile: Constructed out of 6mm thick Medium Density Fiber Board (MDF) confirming
to IS – 12406 and covered with Fabric of choice.
• Laminate Tile: Constructed out of 6mm thick Pre-laminated Particle board edge banded
by 0.4mm PVC edge banding confirming to IS – 12923.
• Glass Tile: 6mm Float glass are used. The Glass can be offered plain, frosted or with
colour films – can be toughened if necessary.
• Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of
choice.
• Glass Marker tiles: 6mm Glass with white Vinyl Backing.
Wire
management -
• Effective Cable management system.
• The data and the power cables can run at different levels (called Raceways) to maintain
the separations as per the IT norms.
• The wire management slots in the frames are large enough to manage high volume of
data cables (CAT-6) - approx- 60-70 CAT-6 cables.
• Vertical movement of the cables in addition to the two/ three levels of horizontal passage
is possible.
• Designed for “clip on” raceway which permits easy maintenance.
• These raceways can be either above or below the tabletop.
• The Skirting raceways are 100 mm and the raceways at the table top level are of 150
mm. The length of the raceways will be matching to the frame width.
• All standard electrical/Data faceplates can be mounted on the raceways at both the
levels. They are fixed “staggered” to ensure electrical safety.
• Additional raceway can be provided to accommodate more cables (if >60 CAT-6 cables)
or sockets.
*450mm Flip-up made of Aluminum in anodised finish, which has soft closure and three
way wire acess with cable dump and vertical wire entry box considered (Size of the flipup
will be changed based on the configuration of the switches).
Support • Work surface will be supported by MS CRCA Cantilever brackets and MSLeg
constructed by using Specially tooled & specifically designed Triangular shape ERW Tube
– 16g, strong Leg bush & levelers made of Acrylonitrile butadiene styrene (ABS), a very
tough material.
•Vertical Member: Connected by a horizontal member 50x25x1.6thk ERW tube. The leg
shoes & levelers made of ABS, a very tough engineering plastic, fitted at the bottom of
vertical tubes, to form a complete leg. The leg construction is strong enough to take care
of the bending stress even if the length of the work surface is more.
• The MS CRCA supports will be powder coated to confirming to IS standard with 50-60
micron thickness.
INTERIOR RENOVATION WORK OF NABARD REGIONAL OFFICE AT 54, WELLESLEY ROAD, P.B.NO. 5, SHIVAJI NAGAR, PUNE-411005
Partition
Sinature and Seal of the bidder Page25
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate(Rs.) Amount (Rs.)
Pdestal unit Mobile pedestal (castor fitted) of size 400mm X 450mm X 640mm(H) with two drawer units
and a file unit, having soft closure and lock & key arrangementy made of prelaminated
particle board of approved shade confirming to E1 norms. Thickness shall be at least
18mm nominal. All the edges of workstation surface shall be provided with machine
pressed 2mm & 0.8 thick PVC lipping glued with hot melt Eva glue free from any VOC.
Work surface edge profile, on edges designed to come into contact with users' wrists shall
compli with ISO 9241-5 (1998) Section 5.4.4, ANSI/HFES-100 (2008) section 8.3.1.4,
BIFMA G1 (2002) Section 9, and CSA-Z412 (2000) section 7.5.12.:
All hardware & channels shall be of approved make.
AGM Tables shall be of Featherlite, Godrej, durian or any other approved
equivallent make
2 Work Stations for Officers and Group B (5'-0" x 5'-0") 96 Nos
Table top Supply and installation of Angular workstations as per layout size of 1500x1500x600mm
& Height 750mm. Made of 25mm thick prelaminated particle board of approved shade
confirming to E1 norms. All the edges of workstation surface shall be provided with
machine pressed 2mm thick PVC lipping glued with hotmelt Eva glue free from any VOC.
Metal CPU trolley and metal Keyboard tray 19" with mouse pad shall be provided under
the table surface.
Leg Leg: Leg constructed by using Specially tooled & specifically designed Triangular shape
ERW Tube – 16g, strong Leg bush & levelers made of Acrylonitrile butadiene styrene
(ABS), a very tough material.
•Vertical Member: Connected by a horizontal member 50x25x1.6thk ERW tube. The leg
shoes & levelers made of ABS, a very tough engineering plastic, fitted at the bottom of
vertical tubes, to form a complete leg. The leg construction shall be strong enough to take
care of the bending stress even if the length of the work surface is more.
Sinature and Seal of the bidder Page26
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate(Rs.) Amount (Rs.)
Cross beam Legs are connected using cross beams made of 40 x 20 16 gauge rectangular tube and
connected to legs with aluminium die cast wing connectors tight fit to leg beam alloted with
4 holes.
Wire
management -
Flipdown tray
Vertical Raceway with built in separator for power, communication and data of size 250H
X 70mm thick with provision to mount swicthes and sockets on laminate facia with Vertical
Wire Entry cover for wire uptake from floor to raceway with 65mm Dia Wire Manager
Grommet.
For entry of cables from the floor into the Raceway, Wire Entry covers are provided
between the intermediate legs with separator for entry of power and data.
Screen 18 mm thick Facbric Magnetic screen of approved colour on Studs with Rubber beading.
Height minimum 350 mm.
Modesty
Panel
12mm pre laminated board Modesty considered on passage side and 18mm thk modesty
panel conisidered on Main side
Pdestal unit Mobile pedestal (castor fitted) of size 400mm X 450mm X 640mm(H) with two drawer units
and a file unit, having soft closure and lock & key arrangementy made of prelaminated
particle board of approved shade confirming to E1 norms. Thickness shall be at least
18mm nominal. All the edges of workstation surface shall be provided with machine
pressed 2mm & 0.8 thick PVC lipping glued with hot melt Eva glue free from any VOC.
Work surface edge profile, on edges designed to come into contact with users' wrists shall
compli with ISO 9241-5 (1998) Section 5.4.4, ANSI/HFES-100 (2008) section 8.3.1.4,
BIFMA G1 (2002) Section 9, and CSA-Z412 (2000) section 7.5.12.:
All hardware & channels shall be of approved make.
Work Stations shall be of Featherlite, Godrej, durian or any other approved equivallent
make
3 SOFAS: -
Providing , Supplying & Installing Sofas, Sofa chairs of various types & categories
(Single seater, Two seater & Three seater) etc complete as per the manufacturers
specifications as mentioned below. The rights to select & approve the sofas &
seating shall vest with the clients. The contractor shall submit brochures of
manufacturer at the time of quoting for this item etc complete as per layout. The
Architect/Employer reserve the right to select the sofas in line with the technical
specifications envisaged & meeting the secifications standards expected.
The minimum standards for the Specifications of Sofas shall be as follows: - Inner
solid Frame structure made of high quality wood. The wood is kiln chemical
treated tropical Meranti wood. The legs are made of rubberwood having melamine
matt finish. The seat cushion is made of 7 inches multi layered foam of density
32D 23D 32D and HD with polyester polyfill outer layer of 180 gsm. The polyester
polyfill keeps the upholstery wrinke free and soft.
The seating cushions have 3 inches of elastic webbing of 350 gsm with proper
weave. The thread used is nylon bonded to provide lasting stitch strength.
Backrest: 2" elastic webbing (250 gsm) with proper Weave and 3" foam (23D) with
Polyester polyfill outer layer (180 gsm). Outer finish: stained solid wooden legs
superior quality. Frame construction: Kiln seasoned mixed meranti solid tropical
hard wood SEAT Webbing 3" proper webbing. Foam: 7" Multilayered foams
Having 4" of High Resilience-HD Foam and 3" of HD virgin PU Foam.
BACKREST: Webbing 2" elastic webbing , Foam: 18D PU foam Upholstery: semi
PU with layer of polyester polywadding Stitiching Nylon thread. Legs Solid kiln
seasoned and treated Solid wood with Melamine Matt Finish.
Sinature and Seal of the bidder Page27
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate(Rs.) Amount (Rs.)
A Leather Sofas
i Single Seater Sofas. 1.00 No.
ii Two Seater Sofas. 5.00 No.
iii Three Seater Sofas. 4.00 No.
B Leatherite Sofas
i Single Seater Sofas. 3.00 No.
ii Two Seater Sofas. 14.00 No.
iii Three Seater Sofas. 31.00 No.
4 Corner Table ( 1'-6" x 1'-6" )
Providing, Supply & installation of Corner table- MATERIALS & DIMENSION (+/-
2mm) - 600L x 600W x 450H. TABLE MATERIALS & SIZE : TOP : SOLID
VENEERED MDF TABLE TOP in 18 mm thickness OR GLASS TOP 10mm.
LEGS: SOLID RUBBER /MS understructure, WOOD. Color : As Approved. LEGS:
Color : As Approved. REST ANY STD COLOUR. The rate shall include including
glass top to have bevelled edges including bottom glass shelf etc complete. The
rate shall also include all the necessary hardware, fittings, fixtures as per
manufactursrs specifications complete.
44.00 No.
5 Center Table (Oval / Rectangular)
Providing, Supply & installation of Centre table- MATERIALS & DIMENSION (+/-
2mm) as mentioned hereinunder. TABLE MATERIALS & SIZE : TOP : SOLID
VENEERED MDF TABLE TOP in 18 mm thickness OR GLASS TOP 10mm.
LEGS: SOLID RUBBER /MS understructure, WOOD. Color : As Approved. LEGS:
Color : As Approved. REST ANY STD COLOUR. The rate shall include including
glass top to have bevelled edges including bottom glass shelf etc complete. The
rate shall also include all the necessary hardware, fittings, fixtures as per
manufactursrs specifications complete.
a Size of table- 4'-0" x 4'-0" (Circular / Square) 2.00 No.
b Size of table- 4'-0" x 2'-0" (Oval / Rectangular) 9.00 No.
c Size of table- 3'-0" x 2'-0" (Oval / Rectangular) 11.00 No.
6 CHAIRS
Sinature and Seal of the bidder Page28
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate(Rs.) Amount (Rs.)
The rights to select & approve the chairs shall vest with the clients. The contractor
shall submit brochures of manufacturer at the time of quoting for this item etc
complete as per layout. The consultants reserve the right to select the chairs in
line with the technical specifications envisaged & meeting the specifications
standards expected.
a
2 No.
b Grade E/D: Providing & supplying Premium Executive High back Chairs as per
the following specification;
*High Back Chair
*Seat Sliding Mechanism
* Adjustable seat depth.
*Duraflex Mesh Seat and Back
*Back reclining & Multilocking synchro meachanism
*Gaslift
*Three way Adjustable Arms with adjustable Headrest
*Adjustable lumber support
*5 flange or more star Chrome base. Twin wheel nylon castor each designed to
sustain weight load of 100 Kg.
*Minimum Height- HB: 114 cm
*Maximum Height- HB: 124 cm
*Minimum Seat Height- 43.5 cm
*Maximum Seat Height- 51.5 cm
*Width (Arm to Arm)- 46 cm
*Minimum Arm Rest Height- 63 cm
Basic Rate Rs.20,000.00
17 No.
Chairman/CGM: Providing & supplying Premium Chief Executive High back
Chairs with leather finish as per the following specification :
Basic rate Rs. 35,000 / -
Overall Dimensions of Chair-Seat Height - min 49.9 to max 58.9 cm. Total Height -
min 134.9 to 143.9 cm.Width & Depth of Chair as measured from pedestal - Width
77 cm and Depth 77 cm SEAT/BACK ASSEMBLY: The seat should be made up of
1.2 ± 0.1cm. thick hot pressed plywood and upholstered with leather and
moulded Polyurethane Foam. The back foam should be designed with contoured
lumber support for extra comfort. BACK SIZE: 53.0cm.(W) X 95.4cm.(H) .
SEAT SIZE: 54.6cm.(W) X 49.0cm.(D). HIGH RESILIENCE (HR)
POLYURETHANE FOAM: The HR polyurethane foam should be moulded with
density = 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf for 25% compression.
SEAT-BACK CONNECTING SPINE:The seat and back should be arrested
together with spine made of 0.8 ±0.05 cm thk HR Steel and should be black
powder-coated ( DFT 40-60 microns ).ARMREST ASSY: The armrest assy. should
comprise of three parts viz. the armrest support tube and P.U. armrest and the
armrest top. The armrest tube assy. should be made of 2.54±0.03cm x
0.16±0.0128cm M.S. E.R.W. support tubes and Chrome plated. The P.U. armrest
should be made of black integral skin polyurethane with 50-70 shore 'A' Hardness
and reinforced with M.S. insert. The armrest top should be made of ABS &
upholstered with foam & leather.FRONT PIVOT SYNCHRO TILT MECH.: The
mechanism should be designed with the following features:•360° revolving
type.•Seat back tilting ratio of 1 : 1.5•Front pivot for tilt with feet resting on ground
ensuring more comfort.•Tilt tension adjustment.•5-position locking with anti-
shock back mechanism, which prevents the backrest from impacting the user
when the lock should be released. •Static seat depth adjustment = 5.0 ± 0.5cm
with 5 position lockin PNEUMATIC HEIGHT ADJUSTMENT: it has an
adjustment stroke of 9.0 ± 0.3cm. BLOW MOULDED BELLOW : The bellow
should be 1 piece and blow moulded in black Polypropylene. PEDESTAL ASSY:
The pedestal should be made of die-cast aluminium with buffing finish. It should
be fitted with 5nos. twin wheel castor. The pedestal should be 67.0 ± 0.5cm pitch-
center dia. (77.0 ± 1.0cm with castors). TWIN WHEEL CASTORS: The twin
wheel castors should be injection moulded in black Nylon.
Basic rate Rs. 54,000 / -
Sinature and Seal of the bidder Page29
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate(Rs.) Amount (Rs.)
c Grade C: Providing & supplying Premium High back Chairs as per the following
specification;
*Medium Back Chair with headrest
*Adjustable seat depth.
*Duraflex Mesh Back
*High Denisty cushion seat
*Back Recline & Multi Locking Function
*Synchro dynaflex Mechanism with Enumatic lift
*Height Adjustable Arms
*In built body flex lumber support
* two piece back construction
*5 flange or more star base. Twin wheel nylon castor each designed to sustain
weight load of 100 Kg.
Seat:
Depth- 51.5 cm
Width- 49.5 cm
Dimensions:
Width- 63.5 cm
Depth- 65.5 cm
Minimum Height- 105.5 cm
Maximum Height- 115.5 cm
Minimum Seat Height- 50.5 cm
Maximum Seat Height- 60.5 cm
Width (Arm to Arm)- 62 cm
Arm Rest Height- 17.5- 26.5 cm
Rs.15000/-
41 No.
d Grade A/B, Group B and meeting rooms: Providing & supplying Premium
Medium back Chairs as per the following specification;
*Medium Back Chair without headrest
*Adjustable seat depth.
*Duraflex Mesh Back
*High Denisty cushion seat
*Back Recline & Multi Locking Function
*Synchro dynaflex Mechanism with Enumatic lift
*Height Adjustable Arms
*In built body flex lumber support
* two piece back construction
*5 flange or more star base. Twin wheel nylon castor each designed to sustain
weight load of 100 Kg.
Seat:
Depth- 51.5 cm
Width- 49.5 cm
Dimensions:
Width- 63.5 cm
Depth- 65.5 cm
Minimum Height- 105.5 cm
Maximum Height- 115.5 cm
Minimum Seat Height- 50.5 cm
Maximum Seat Height- 60.5 cm
Width (Arm to Arm)- 62 cm
Arm Rest Height- 17.5- 26.5 cm
Basic Rate Rs.13500/-
170 No.
Sinature and Seal of the bidder Page30
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate(Rs.) Amount (Rs.)
e
8 No.
f Visitors for Grade E/D/C : Providing & supplying visitor Chairs as per the
following specifications;
SIZE :- (W)620mm X (D)590mm X (H)830mm LOW Mesh back
/Adjustable Back Folding chair /Sleek Aluminium scissor frame
Basic Rate Rs.13500/-
148 No.
53 No.
g
Visitors for Chairman/CGM: Providing & supplying Premium Chief Executive
visitor Chairs with leather finish as per the following specifications;
Overall Dimensions of Chair-Seat Height - min 43.4 to max 55.4 cm.
Back Height - min 99.4 to 111.4 cm.Width & Depth of Chair as measured from
pedestal - Width 77 cm and Depth 77 cmSEAT/BACK ASSEMBLY: The seat
should be made up of 1.2 ± 0.1cm. thick hot pressed plywood and upholstered
with leather and moulded Polyurethane Foam. The back foam should be designed
with contoured lumber support for extra comfort. BACK SIZE: 53.0cm.(W) X
73.0cm.(H)
SEAT SIZE: 54.6cm.(W) X 49.0cm.(D). HIGH RESILIENCE (HR)
POLYURETHANE FOAM: The HR polyurethane foam should be moulded with
density = 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf for 25% compression.
SEAT-BACK CONNECTING SPINE:The seat and back should be arrested
together with spine made of 0.8 ±0.05 cm thk HR Steel and should be black
powder-coated ( DFT 40-60 microns ). ARMREST ASSY: The armrest assy.
should comprise of three parts viz. the armrest support tube and P.U. armrest and
the armrest top. The armrest tube assy. should be made of 2.54±0.03cm x
0.16±0.0128cm M.S. E.R.W. support tubes and Chrome plated. The P.U. armrest
should be made of black integral skin polyurethane with 50-70 shore 'A' Hardness
and reinforced with M.S. insert. The armrest top should be made of ABS &
upholstered with foam & leather. SEAT BASE ASSY. : The seat base assy. should
be designed with following features:
360° Revolving type without back tilt. PNEUMATIC HEIGHT ADJUSTMENT : it
has an adjustment stroke of 12.0 ± 0.3cm. TELESCOPIC BELLOW ASSEMBLY :
The bellow should be 3 piece telescopic type and injection moulded in black
Polypropylene PEDESTAL ASSY: The pedestal should be made of die-cast
aluminium with buffing finish. It should be fitted with 5nos. twin wheel castor.
The pedestal should be 67.0 ± 0.5cm pitch-center dia. (77.0 ± 1.0cm with
castors). TWIN WHEEL CASTORS: The twin wheel castors should be injection
moulded in black Nylon
Basic Rate Rs.40000/-
For Conference room (Front row) & Multipurpose room at 1st floor: Providing
and supplying high back chairs with following specifications;
SEAT ASSEMBLY : The Cushioned seat should be made of Injection molded
Plastic outer & inner. Plastic Inner should be upholstered with leatherette and
moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,and
hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. *Seat SIZE : 47.0
cm. (W) x 48.0 cm. (D) BACK ASSEMBLY: The Cushioned back should be made
of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16
±0.0128cm. It upholstered with Leatherette. (D) *MID BACK SIZE: 47.7 cm. (W)
x 60.1 cm. (D) ARMRESTS (FU3301/FU3302) : The armrest top should be
moulded from polyurethane(PU) and mounted on to a drop lift adjustable type
tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk M.S. E.R.W
tube having chrome plated finish.The armrest height adjustable up to 6.5±0.5cm
in 5 steps. ACTIVE BIO-SYNCHRO MECHANISM- The adjustable tilting
mechanism should be designed with the following features: • 360' revolving type. •
Front-pivot for tilt with feet resting on ground and continuous lumbar support
ensuring more comfort. • Tilt tension adjustment can be operated in seating
position. • 5-position Tilt limiter giving option of variable tilt angle to the chair. •
Seat/back tilting ratio of 1: 2 • The mechanism housing should be made up of
HPDC Aluminium black powder coated. SEAT DEPTH ADJUSTMENT
(FU3301/FU3302): Seat depth adjustment should be integrated in the seat
through a sliding mechanism. Seat depth adjustment range should be of 6.0±0.5
cm. ADJUSTABLE BACK SUPPORT (FU3301/FU3302): Back Frame should be
connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted
in the range of 7.42±0.5 cm for the comfortable back support to suit individual
need. PNEUMATIC HT. ADJUSTMENT (FU3301/FU3302): The pneumatic ht
adjustment has an adjustment stroke of 10.0±0.3 cm. PEDESTAL ASSEMBLY
(FU3301/FU3302): The pedestal should be High Pressure Die cast polished
Aluminium and fitted with 5 nos. twin wheel castors. The pedestal should be 65.0
± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.) TWIN WHEEL CASTORS:
The twin wheel castors should be injection moulded in black PP having 6.0±
0.1cm wheel Diameter.
Basic Rate Rs.15000/-
Sinature and Seal of the bidder Page31
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate(Rs.) Amount (Rs.)
6 No.
For conference room back row: Providing & supplying chairs as per the following
specifications;
SEAT ASSEMBLY : The Cushioned seat should be made of Injection molded
Plastic outer & inner. Plastic Inner should be upholstered with leatherette and
moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,and
hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. t SIZE : 47.0 cm.
(W) x 48.0 cm. (D) BACK ASSEMBLY: The Cushioned back should be made of
PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16
±0.0128cm. It upholstered with Leatherette. BACK SIZE: 47.7 cm. (W) x 60.1 cm.
(D) .Visitor TUBULAR FRAME: The tubular frame should be cantilever type and
made of Ø2.54± 0.03 cm X 0.02 ± 0.016cm thick SS 202 tube. The back should be
connected to frame through chrome plated high pressure die case connector piece.
Basic Rate Rs. 12000/-
39 No.
h Viping Dining Chairs: Providing and supplying chairs with following
specifications;
Size :-(W)540mm X (D)530mm X (H)1010mm / Revolving / Mesh Back / Fixed
Back Chrome frame and Cantilever Base .
Basic Rate Rs.9000/-
32 No.
i Normal Dining Chairs:
Providing and supplying cafeteria stackable chairs with Chromeplated Legs and
without Arms. As approved by Client/Architect.
Basic Rate Rs.3000/-
128 No.
SUM TOTAL OF SCHEDULE - MODULAR LOOSE FURNITURE WORKS Rs.
Please Note : The rates quoted hereinabove shall be Exclusive of GST and
GST shall be additional at actuals.
SEAL AND SIGN OF BIDDER
g
For Chairperson (Conference room & Multipurpose room): Providing and
supplying high back chairs with following specifications;
SEAT ASSEMBLY : The Cushioned seat should be made of Injection molded
Plastic outer & inner. Plastic Inner should be upholstered with leatherette and
moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,and
hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. *Seat SIZE : 47.0
cm. (W) x 48.0 cm. (D) .BACK ASSEMBLY: The Cushioned back should be made
of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16
±0.0128cm. It upholstered with Leatherette. BACK SIZE: 47.7 cm. (W) x 76.4 cm.
(D) . ARMRESTS : The armrest top should be moulded from polyurethane(PU)
and mounted on to a drop lift adjustable type tubular armrest support made of
03.81±0.03 cm x 0.2±0.01 cm thk M.S. E.R.W tube having chrome plated
finish.The armrest height adjustable up to 6.5±0.5cm in 5 steps. ACTIVE BIO-
SYNCHRO MECHANISM : The adjustable tilting mechanism should be designed
with the following features: • 360' revolving type. • Front-pivot for tilt with feet
resting on ground and continuous lumbar support ensuring more comfort. • Tilt
tension adjustment can be operated in seating position. • 5-position Tilt limiter
giving option of variable tilt angle to the chair. • Seat/back tilting ratio of 1: 2 •
The mechanism housing should be made up of HPDC Aluminium black powder
coated. SEAT DEPTH ADJUSTMENT : Seat depth adjustment should be
integrated in the seat through a sliding mechanism. Seat depth adjustment range
should be of 6.0±0.5 cm. ADJUSTABLE BACK SUPPORT: Back Frame should be
connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted
in the range of 7.42±0.5 cm for the comfortable back support to suit individual
need. PNEUMATIC HT. ADJUSTMENT: The pneumatic ht adjustment has an
adjustment stroke of 10.0±0.3 cm. PEDESTAL ASSEMBLY: The pedestal should
be High Pressure Die cast polished Aluminium and fitted with 5 nos. twin wheel
castors. The pedestal should be 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm.
With castors.) TWIN WHEEL CASTORS: The twin wheel castors should be
injection moulded in black PP having 6.0± 0.1cm wheel Diameter.
Basic Rate Rs.16000/-
Sinature and Seal of the bidder Page32
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate (Rs.) Amount (Rs.)
5. SCHEDULE - CIVIL WORKS
I GENERAL CIVIL WORKS
1 Demolition / dismantaling
Demolishing/dismantaling of the existing Flooring, dado, tiling,
partitions, false ceiling, Platforms, counters, stone or brick work,
plaster, bunds, walls, doors, windows, fans, lighting fixtures, cables &
wires, AC ducts & grills, AC assessories, Fire pipes, Sprinklers,
Electrical Assessories, table & credenzas, storage units of all types,
furniture & fixtures, workstations, Interior items, fixed & loose items etc
and any other material required for working on site & compliance of all
the activities on site including removal of debris from site including
removing the same with utmost care to ensure no damage in case of
fixtures & fittings & handing over the same to the organization or
shifting the same to a new desired place and re-fixing the same if
desired under the instructions and directions of the Consultant.
1.00
2 Walls :
Providing and erecting in position, level and plumb 6" thk siporex walls
in cement mortar 1:6 ( 1 cement : 6 coarse sand ) etc. complete 305.43 Sq. Mts
150mm thk Siporex masonary wall
3 Plastering
Carefully breaking & removing the existing plaster in patches or long
stretches without damaging the plaster, brickwork in the vicinity
including cutting a groove first to demarcate exact area & providing and
applying internal cement plaster in patches or long stretches over the
removed plaster portion in C.M. 1:4 upto average 20 mm thickness,
including addition of water proof chemicals of approved makes,
providing bands, drip moulds, grooves, scaffolding, curing for 7 days,
application of Terraco Spray after cement plaster has dried out etc.
complete. DSR 2016 Sr.No. 13.6.1 PAGE NO.227
698.99 Sq. Mts
4 PAINTING :
Note : The Rates for the Painting works shall be inclusive of three
coats. The paint should be free from lead and Arsenic.
A Painting of wall with minimum of 3 coats with Lustre Paint of approved
shade & make on the wall, plywood or gypboard including all necessary
surfaces preparation, scrapping, base coats etc to receive 3 coats. The
wall shall be cleaned, filled with putty & applied with one coat of primer
so as to achieve a even surface to apply paint as per the directions / to
the satisfaction of the Architect.
92.90 Sq. Mts
B Providing and applying acrylic aggregate textured wall coating in oikos
pigmented Ornaplast finish in any shade spray coat bubble or compact
or rustik shade, maintaining material consumption rate of average 2.25
Kg. Per sq.mt. and 1.5mm thickness on walls. The rate shall include
POP punning to the wall up to average thickness of 12 mm to proper
level & plumb, including grooves etc, scrapping, base coats etc,
cleaning of the walls etc complete.
27.87 Sq. Mts
INTERIOR RENOVATION WORK OF NABARD REGIONAL OFFICE AT 54, WELLESLEY ROAD,
P.B.NO. 5, SHIVAJI NAGAR, PUNE-411 005.
Lumpsum
Sinature and Seal of the bidder Page33
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate (Rs.) Amount (Rs.)
C Providing and applying Acrylic Emulsion Paint in minimum of three
coats of approved make and shade on Walls, Ceiling, plywood, gypsum
board, surfaces etc including all the necessary surfaces preparation,
POP punning to the wall up to average thickness of 12 mm to proper
level & plumb, including grooves etc scrapping, base coats etc to
receive 3 coats of paint. The wall shall be cleaned, filled with putty &
applied with one coat of primer so as to achieve a even surface to apply
paint. As per the directions / to the satisfaction of the Architect.
603.86 Sq. Mts
5 FLOORING :
A (i) Providing and laying 9mm thk Mirror finish super-premium range, digital
and high gloss Vitrified Tiles of approved reputed makes of size 600 x
600 x 9mm thk (Min) laid in required pattern on an avg. 25 to 30mm thk.
bed of 1:4 cement mortar (1 cement : 4 coarse sand) including inlay
design work in 18mm thk Granite stone and contrast dark coloured
Vitrified tiles approved by the Architects and approved design in proper
line and level including neat white cement float, filling joints with neat
cement slurry, of appropriate colour, curing and cleaning complete.Tiles
shall be free of any variation in colour or texture, and laying plastic
sheet & 18mm thk. POP protective cover on flooring and removing
when directed.
1200.29 Sq. Mts
The cost to include sealer treatment of Aqua mix brand. The rate shall
be inclusive of application chemicals and Roffe and levelling with min 3"
PCC (To be paid for seperately under relevant item) wherever level
difference is observed to attain a uniform level all throughout the
premises. The rate shall also include providing and fixing heavy duty
brass patti of desired length, width for the areas of the inlay works etc
complete as directed by the Architects. (Basic rate of tiles = Rs. 80 / Sq
Fts plus taxes {GST}) DSR 2016 Sr.No. 11.41.2 Page No.197
A (ii) Providing and laying 9mm thk super premium range and Anti-skid Matt
finish premium range approved Vitrified Tiles for toilets of reputed
approved make of size 600 x 600 x 9mm thk (Min) laid in required
pattern on an avg. 25 to 30mm thk bed of 1:4 cement mortar (1 cement
: 4 coarse sand) in proper line and level including neat white cement
float, filling joints with neat cement slurry, of appropriate matching
colour, curing and cleaning complete.Tiles shall be free of any variation
in colour or texture. The cost to include sealer treatment of Aqua mix
brand. The rate shall be inclusive of application chemicals and Roffe
and levelling with min 3" PCC wherever level difference is observed to
attain a uniform level all throughout the premises. (Basic rate of tiles =
Rs. 90 / Sq Fts plus taxes {GST})
155.14 Sq. Mts
B Providing and laying Laminated Wooden flooring of approved make on
floor as per the drawing & instructions on levelled floor including
levelling the surface of application area with min 3" P.C.C (To be paid
for seperately under relevant item), insulating the areas, surface
preparation, bedding, finishing, polishing, cleaning etc complete as per
the directions and instructions of the Consultant.
504.02 Sq. Mts
Sinature and Seal of the bidder Page34
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate (Rs.) Amount (Rs.)
The rate shall be inclusive of edge moulding & end strips at the junction
between the floor and the vertical surfaces and mouldings, T grooves
etc complete.As per the directions / to the satisfaction of the Architect.
The rate shall also include making a cutout along the peripheral areas
of the wooden flooring of about 2" depth and 6" width and filling the
same with white pebbles including artificial planters complete for the
entire length of the cut out and including providing 12mm thk toughened
glass over the said cut out, necessary arrangements for fixing the
glass, fittings, fixtures, hardware, backing etc complete as directed by
the Architect. (Basic rate of tiles = Rs. 180 / Sq Fts plus taxes {GST}.)
C Providing and fixing 18mm thk approved coloured stellar slab
(Sparkling slabs) for the inlay work in the flooring or designer work in
dado wherever instructed of standard size in a required pattern and
design including Cement Mortar 1:4 ( 1 Cement : 4 Coarse sand ) in
proper line and level including neat white cement float, filling joints with
neat cement slurry, of appropriate colour, curing and cleaning
complete. Slabs shall be free of any variation in colour or texture. Other
inlays would be paid for seperately under the relevant item. (Basic rate
of stellar Rs. 300 / Sq Fts plus taxes {GST})
88.25 Sq. Mts
D Providing and fixing approved Mirror polished approved premium range
Granite slab flooring (Sparkling Jet Black / Raw Silk / Black Pearl or
equivalent approved) for toilet flooring, inlay & design works, staircase
treads & risers, landings, bunds, cills in single or double patti (double
patti would be considered and measured as single length X total width
irrespective of single or double thickness), urinal partitions, jambs,
strips & door frames etc in 18mm thk granite and size upto 8' x 6' over
and including avg 25 to 30mm thk. 1:4 (1 cement : 4 coarse sand)
bedding in proper line & level including the joints to be finished flushed
in matching colour cement, curing, washing, cleaning and rate to
include for chipping and levelling existing floor and laying plastic sheet
& 18mm thk. POP protective cover on flooring and removing when
directed as req., including moulding and 1/8" grooves complete as per
drawings & details, and as directed.
557.41 Sq. Mts
The rate shall also include providing and fixing heavy duty brass patti of
desired length, width for the areas of the inlay works etc complete as
directed by the Architects. (Basic rate of Granite shall be Rs. 225 / sq
fts plus taxes {GST}). DSR 2016 Sr.No. 8.13.1 PAGE NO.130
E Providing and laying in position approved Granolithic high gloss, super
premium range 18mm thk Italian Marble flooring in sizes and pattern
including design inlay work in approved dark coloured italian marble
(Strip design or irregular dark marble design patterns) wherever
specified as shown in the drawing over and including avg. 25 to 30mm
thk. 1:4 white cement mortar bedding, joints finished flush in matching
colour cement, curing, rubbing, machine mirror grade polishing,
washing, cleaning and sealer for anti-stain of Aqua mix brand etc. rate
to include for chipping and leveling existing floor as required, complete
and laying plastic sheet & 18mm thk. POP protective cover on flooring
and removing as per the directions of Architect. The rate shall also
include providing and fixing heavy duty brass patti of desired length,
width for the areas of the inlay works etc complete as directed by the
Architects. (Basic Rate of Italian Marble : Rs. 450/- Sq.ft plus taxes
{GST}) DSR 2016 Sr.No.11.51 PAGE NO.198
353.18 Sq. Mts
Sinature and Seal of the bidder Page35
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate (Rs.) Amount (Rs.)
F Providing and laying Dado works inside the toilet walls and for areas as
directed in the following combination & design: - 576.60 Sq. Mts
i Providing & Laying Designer digital series dark colored vitrified tiles of
size such as 12" X 18" or 12" X 24" etc or appropriate size as approved,
super premium range (in contrast) of approved make and shade sich as
RAK or equivalent and laid matching the base dado tile grooves for an
height upto 3'-0" of toilet walls or top of the wash basin counter level,
whichever is higher and from the finished floor level. Basic rate of
Designer Vitrified tiles shall be Rs. 125 / sq fts plus taxes {GST}.
ii Providing & Laying above the said Granite, contrast dark colored
Granite patta of size 4" shall be provided at wash basin counter fascia
level or as directed and also above the vitrified tiles at 7'-0" level
iii Providing & Laying above the Granite patta, Super premium range,
designer digital series high gloss Vitrified tiles dado upto a height of 7'-
0" or the door height, whichever is higher in sizes such as 12" X 18" or
12" X 24" or appropriate size as approved and matching the base dado
tile grooves of reputed make such as RAK or equivalent and shade
including designer tiles as per manufacturers standards in combination.
(Basic Rate of Tile shall be Rs. 90/- S.Fts plus taxes {GST})
iv Providing & Laying above the said Vitrified tiles dado, Granite patta of
size 4". The granite patta shall also be provided above the door as well
as ventilators / windows of the toilets.
v The Granite and the tiles mentioned above in this item shall be laid in a
required pattern and design and the rate shall include fixing the same
with Cement Mortar 1:4 ( 1 Cement : 4 Coarse sand ) in proper line and
level including neat white cement float, filling joints with neat cement
slurry of appropriate colour, curing and cleaning etc complete. Tiles
shall be free of any variation in colour or texture.
6 Pantry Counter
Providing and erecting pantry counter 2'-0" wide pantry / kitchen
counter with cudappa undercarriage frame, 11/2" thk with one side
polished and top to be finished with 18 mm thk jet black granite in the
desired shape & size including half round nosing & grooves. The
undercarriage frame of the counter shall be in sandwitch cadappa
verticals with granite facia of size 6" to be fixed to verticals and top of
the counter & nosing with edge polish including a cut-out for sink etc
complete as per directions & instructions of the Architect.
20.13 Rmt.
The rate shall be inclusive of providing & fixing modular kitchen
arrangement for the complete & entire length and height of the counter
in Stainless Steel 304 including S.S service trolleys below with standard
sliding channel sections as per manufacturers specifications, S.S Sink
with drain board of nirali make of size minimum of 24" X 17"X 8" and
including necessary water supply & drainage pipe lines, plumbing
fittings & fixtures of jaguar of approved equivalent make etc complete
as per the directions & to the satisfaction of the Architect.
The execution of the said work shall be strictly in accordance with the
detailed drawing issued as a part of the tender document. 2 Nos of
kitchens shall be considered for quantification & the item shall be
operated considering all the elements mentioned herein as a part of the
BOQ specifications to be executed for the entire length of the counter,
which is to be quantified in Running metres length and for the scope of
work as defined herein to be read along with the detailed drawing.
Specifications to be provided for each of the 2 Nos of Kitchens shall
comprise of the following items / elements:
Sinature and Seal of the bidder Page36
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate (Rs.) Amount (Rs.)
a Plain shelf unit 600mm with centre adjustable shelf
b Dish kit 600 mm with spoon tray, dish trolley
c Gas cylinder unit with gas trolley
Sinature and Seal of the bidder Page37
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate (Rs.) Amount (Rs.)
d Drawer cabinets 800mm in tandom drawer for the entire length of
the platform, horizontal partition, vertical divider etc
e Bottle pull out unit 300mm for spice bottles
f Lemons corner unit 1000mm for with centre adjustable shelf
g Corner units left, right etc, Carrousal, D-tray,
h Utensils kit 600mm for utensils
i Plain baskets in SS 304 for the entire length and height of the
platform, Cup and saucer baskets in SS 304, Perforated cutlery
baskets in SS 304, Thali - Plate baskets in SS 304 for the entire
length and height of the platformsj Trolleys of all types & utilization in SS 304 for the entire length
and height of the platforms
k Cutlery organizer, waste bins in SS with holders etc complete
l Sink unit 700mm with dust bin holder & detergent trolley
m Hood chimney 60 cm wide, 1200 m3/h air extraction rate,
Autoclean touch hood with LED display, Baffle Filters, Wall mount
design including exhaust arrangements, fans, ducting system,
window mounted exhaust assessories etc complete
7 Providing and Fixing Synthetic Door matting of approved make as per
manufacturers specifications to match the finished floor level in the
adjoining areas19.50 Sq. Mts
8a Providing & placing in position Stainless steel perforated Dustbins of
standard manufacturers specifications and make etc complete as
instructed by EIC.26.00 Nos
b Same as above but Providing & placing in position Plastic Dustbins of
standard manufacturers specifications and make etc complete as
instructed by EIC.86.00 Nos
9 Plumbing work
Providing and fixing in position internal and external damaged Sanitary
and Water supply pipelines to be PVC and / or c-PVC concealed in wall
/ floor with bitumen treatment and covered with hessain cloth. All joints
to be water tight and properly sealed. Drainage pipes shall be heavy
duty ISI marked including all necessary high quality fitting such as
bends, tees, flanges, elbows, coupling, reducer, unions, checknuts etc.
joining with taflon tapes, excavation, refilling, consolidating where ever
required. Note: - since all the pipelines are already covered under the
respective items of WC's and Wash basins, the said item shall be
operated and items quntified only as per the directions of the Architect
or Client and whenever any additional pipelines are required to be laid
within the toilets or any other area, within the premises and on the floor.
a 1/2" G.I Water Supply Pipe including screewed sockets, joints and all
the necessary G.I fittings such as backnuts, elbows, connector with G.I
sleeves, bends, tees, reducers, enlargers, plugs etc including two coats
of oil paint & one coat of primer etc complete.
182.92 R.mt
b 3/4" G.I Water Supply Pipe including screewed sockets, joints and all
the necessary G.I fittings such as backnuts, elbows, connector with
PVC sleeves, bends, tees, reducers, enlargers, plugs etc including two
coats of oil paint & one coat of primer etc complete
71.64 R.mt
c 1" G.I Water Supply Pipe including screewed sockets, joints and all the
necessary G.I fittings such as backnuts, elbows, connector with PVC
sleeves, bends, tees, reducers, enlargers, plugs etc including two coats
of oil paint & one coat of primer etc complete
36.58 R.mt
Sinature and Seal of the bidder Page38
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate (Rs.) Amount (Rs.)
d 2" G.I Water Supply Pipe including screewed sockets, joints and all the
necessary G.I fittings such as backnuts, elbows, bends, tees, reducers,
enlargers, plugs etc including two coats of oil paint & one coat of primer
etc complete
54.87 R.mt
e PVC SOIL PIPE (4") with all its fittings, fixtures etc complete 100.6 R.mt
f PVC WASTE WATER PIPE (4") with all its fittings, fixtures etc complete121.95 R.mt
g PVC VENT PIPE (3") with all its fittings, fixtures etc complete 106.7 R.mt
h Alterations in the exterior drainage lines by providing new PVC lines in
place of the old lines including necessary connections to be provided to
upto the manholes on the Ground floor including creation of new
manholes & I.C's, connection upto the interconnected existing
chambers of the building etc complete including matching diameter of
the existing pipelines.
1.00 Lot
10 Sanitary Ware
A Providig and fixing of off-white coloured sanitaryware of approved make
and shape.
i Wall mounted EWC (36X34.5X54.5cms) including its complete set of
assessories such as flushing cistern - flush tank, water jet arrangement,
telephone jet arrangement for WC, M.S.chair - PVC seat cover, bends,
other assessories, fittings, fixtures etc complete including necessary
drainage connections (internal and external upto the external face of
the building) including water supply & drainage pipeline etc complete.
The rate shall also be inclusive of concealed water supply pipelines in
cPVC for flush tank / flush valve from external point source upto the
flush valve / flush tank, water jet and telephone jet etc complete.
20.00 Nos.
ii Large flat back urinals (59X39X37.5cms) including premium range
granite urinal partitions and necessary fittings and fixtures etc complete
in all respects as per manufacturers specifications, standard fittings &
fixtures. The rate shall be inclusive of necessary drainage connections
(internal upto the nahani trap and external upto the external face of the
building) including water supply & drainage pipeline etc complete. The
rate shall also be inclusive of concealed water inlet supply pipelines in
cPVC for wash basin from external point source etc complete.
19.00 Nos.
iii Same as EWC above, but Orisa Pan (Comfort) (58X43cms) including
its complete set of assessories such as flushing cistern - flush tank,
water jet arrangement, telephone jet arrangement for WC, bends, other
assessories, fittings, fixtures etc complete including necessary drainage
connections (internal and external upto the external face of the building)
including water supply & drainage pipeline etc complete. The rate shall
also be inclusive of concealed water supply pipelines in cPVC for flush
tank / flush valve from external point source upto the flush valve / flush
tank, water jet and telephone jet etc complete.
8 Nos.
iv Round / Oval shaped over mounted wash basin (46X46X17cms)
including premium range granite counter with moulding below the basin
including heavy duty bottle trap, waste coupling, pillar cock with sensor
arrangement, stop cock and necessary fittings and fixtures etc.
complete in all respects as per manufacturers specifications, standard
fittings & fixtures, shutters below the granite counter in marine ply etc
complete. The rate shall be inclusive of in-built heavy duty sensors and
necessary drainage connections (internal upto the nahani trap and
external upto the external face of the building) including water supply &
drainage pipeline etc complete. The rate shall also be inclusive of
concealed water supply pipelines in cPVC for wash basin from external
point source etc complete.
39 Nos
Sinature and Seal of the bidder Page39
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate (Rs.) Amount (Rs.)
v Water Closet for Differently-abled including its complete set of
assessories such as flushing cistern - flush tank, water jet arrangement,
telephone jet arrangement for WC, M.S.chair - PVC seat cover, bends,
other assessories, fittings, fixtures etc complete including necessary
drainage connections (internal and external upto the external face of
the building) including water supply & drainage pipeline etc complete.
The rate shall also be inclusive of concealed water supply pipelines in
cPVC for flush tank / flush valve from external point source upto the
flush valve / flush tank, water jet and telephone jet etc complete.
4.00 Nos.
B Sanitary Fittings & Fixtures
Providing and fixing CP sanitary fittings of approved make as follows.
i Angle Cock 42.00 No.
ii Stop Cock 10.00 No.
iii Water jet for WC's 31.00 No.
iv Bib Cock 85.00 No.
v Soap Holder 26.00 No.
vi Towel Rod 26.00 No.
vii Coat Hooks 31.00 No.
viii Nahani Trap jali 45.00 No.
ix Pillar cock 15.00 No.
x CP brass Liquid Soap containers 26.00 No.
xi Providing and fixing in position Askon make Hand Dryer 10.00 No.
xii Providing & fixing Exhaust Fans in aluminium frame including Frames
for Exhaust Fans of appropriate size etc complete31.00 No.
xiii Providing and fixing in position counter mounted fancy fittings in toilet
area such as Glass Wash basins including special fancy designer and
decorative basin mixer, fittings, fixtures, assessories, traps etc. The rate
shall include fixing the wash basin within the counter (Granite counter to
be paid for seperately under relevant item)
2.00 No.
xiv Providing & fixing Urinal Sensor flushing, electric operated etc complete23.00 No.
11 Aluminium Sliding Window
Providing and fixing bronze anodised aluminium window with 5.5mm
thk. tinted glass and sliding / fixed shutters in aluminium window
sections with proper locking arrangement and smooth movements
including approved sun control film etc. complete as per instructions of
Architect.
250.00 Sq. Mts
Sinature and Seal of the bidder Page40
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate (Rs.) Amount (Rs.)
12 Removing the existing waterproofing including disposal & catring away
of debris, cleaning etc and to exposed the bare RCC slab, clean the
RCC slab surface & wall for treatment by removing dust, dirt and layers
of concrete over the surface. etc. by mechanical means. Drilling holes
at construction joints and identify damaged / honeycombed of the
concrete surface and fixing PVC nozzles at 2-3 ft c/c and sealing the
same with PMM or equivalent, then total area to be filled with water
minimum 6” deep for minimum 3 days, after specific period of ponding
slab shall be checked for leakage/ seepage even dampness and such
area shall be marked and pressure grouting / crack filling shall be done,
Identifying the cracks, construction joints & filling the same with
Polymer Modified Mortar using POLYALK EP or equivalent. Injection
grouting shall be done with providing and injection non shrink
cementations grout by mixing – 2 pouches (330 gms. Each) of
SUNPLEX or equivalent and 50 kgs of cement and sufficient water for
flow ability. Grouting the same under pressure in pre-drilled holes by
grouting pump etc complete. After grouting is completed after 24 hours,
cut the nipples and seal it with PMM or equivalent etc complete. After
completion of crackfilling & grouting again ponding shall be done for
specific period to ensure the success of pressure grouting, if there is no
leakages/ seepage/ dampness then only further activities shall be
started.
155.14 Sq. Mts
Providing and applying two coats of POLYALK WP or equivalent and
cement in 1:1.25 ratio at an interval of 24 hours on the slab and
extending it upto 1’0” over the F.F.L. Air cure the same for 24 hours and
damp cure for next 4-5 days. Providing and applying single coat of
bonding agent HACK-AID-PLAST or equivalent on the POLYALK WP
or equivalent coating by spray and providing wet on wet a chat/dash
coat of 1:4 cement mortar in 10-12 mm thickness. All mortar mix to be
necessarily added with SUNPLEX or equivalent 330 gms pouch per 50
Kg bag of cement. All coats of POLYALK WP or equivalent to be
inspected using a Magnifying glass by the EIC to satisfaction to ensure
pinhole free coating. Ensure mechanical mixing of POLYALK WP or
equivalent and cement slurry using stirrers and check that cement
particles do not settle down in the prepared mix. Consume the prepared
mix within 30 minutes.
Lay an average 2½” thick well soaked brick bat metal coba in cement
mortar 1:4 to proper level and slope as per instructions adding
SUNPLEX or equivalent - 330 gms pouch per 50 Kg bag of cement to
the mortar mix. Fill up the brick joints and lay metal coba in C:M 1:4
adding SUNPLEX or equivalent - 330 gms pouch per 50 Kg bag of
cement and finished with chequered markings for further provision of
floor tiles. Rate to include ponding for seven days by closing the SWR
and soil outlets etc complete to the satisfaction of the EIC.
13 Multipurpose Service Counter
Providing and erecting Bain Marrie Multi purpose Granite Service
counter 2'-0" wide with brick work supporting arrangement & cudappa
undercarriage frame, 11/2" thk with one side polished and top to be
finished with 18 mm thk black pearl granite in the desired shape & size
including half round nosing & grooves. The undercarriage frame of the
counter shall be in sandwitch cadappa verticals with black pearl granite
facia of size 6" to be fixed to verticals and top of the counter & nosing
with edge polish including cut-outs for buffet arrangements & placing
containers etc complete as per directions & instructions of the Architect.
19.81 Rmt.
Sinature and Seal of the bidder Page41
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate (Rs.) Amount (Rs.)
The rate shall be inclusive of providing & fixing modular S.S service
trolleys below with standard sliding channel sections, fittings & fixtures
and hardware as per manufacturers specifications for the complete
length and height of the counter including necessary provisions for
heating arrangements, boiling water, necessary gas, water supply &
drainage pipe-lines etc complete. the rate shall also include providing
and fixing 3 nos of SS pipes in front of the counter including the side
frames, brackets in SS including wedge type brackets in SS to be fixed
to the verticals of the granite counter etc complete. The rate shall also
include providing and fixing shutters in Commercial plywood beneath
the entire length of the counter including the necessary t.w framework
and to be finished with 4.0 mm thk high end veneer with melamine
polish.
14 Providing and laying 9mm thk Mirror finish super-premium range, digital
and high gloss Vitrified Tiles of approved reputed makes and of size
1000 x 1000 x 9mm thk (Min) laid in required pattern on an avg. 25 to
30mm thk. bed of 1:4 cement mortar (1 cement : 4 coarse sand)
including inlay design work in 18mm thk Granite stone and contrast
dark coloured Vitrified tiles approved by the Architects and approved
design in proper line and level including neat white cement float, filling
joints with neat cement slurry, of appropriate colour, curing and
cleaning complete.Tiles shall be free of any variation in colour or
texture, and laying plastic sheet & 18mm thk. POP protective cover on
flooring and removing when directed.
338.62 Sq. Mts
The cost to include sealer treatment of Aqua mix brand. The rate shall
be inclusive of application chemicals and Roffe and levelling with min 3"
PCC wherever level difference is observed to attain a uniform level all
throughout the premises. The rate shall also include providing and
fixing heavy duty brass patti of desired length, width for the areas of the
inlay works etc complete as directed by the Architects. (Basic rate of
tiles = Rs. 220 / Sq Fts.)
15 Providing PCC of minimum 4" beneath the floor finishes wherever level
difference is observed to attain a uniform level all throughout the
premises287.99 Sq. Mts
TOTAL OF GENERAL CIVIL WORKS Rs.
Sinature and Seal of the bidder Page42
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate (Rs.) Amount (Rs.)
II INTERNAL CIVIL RESTORATION WORKS
1 PATCHWORK CONCRETE (M20)
Carefully breaking, removing and exposing the existing loose &
damaged concrete in patches or long stretches by means of light chisel
including supplying, providing & errecting in position the necessary
scaffolding, disposal & cating away of the debris, cleaning etc. complete
& providing and laying M-20 concrete in patches with 10 to 20 mm
downgraded aggregate as required, including providing the necessary
formwork, water tight and removal after prescribed duration,
compaction, curing, chipping of excess concrete and bringing it to
original profile etc. complete. The rate shall include the usage of
appropriate chemicals, setting agents etc of Sunanda or equivalent
manufacturer etc complete.
2 Cu.Mts
Note:
1. Quoted rate shall be inclusive of additional concreting done and
applying protection coat of polymer + cement (1:1 by volume) to
existing reinforcement, which will not be paid seperately.
2. Hammers weighing more than 2 kg shall not be used. The rate shall
also include the replacement of the totally corroded and damaged
reinforcement steel bars wherever necessary & directed including
welding, lapping, clening etc complete.
2 POLYMER MODIFIED MORTAR/CONCRETE
Carefully breaking & removing the existing damaged / corroded R.C.C.
Columns, beam, slabs, chajjas, paradis, fins etc including disposal &
cating away of the debris, cleaning etc in the patches or long stretches
by means of light chisel upto 50mm depth, upto the level of
reinforcement without damaging brickwork, plaster in the vicinity,
including supplying, providing & errecting in position the necessary
scaffolding, cleaning, disposing of debris etc complete & then providing
and applying polymer modified cementatious mortar treatment upto 50
mm thk. comprising of following operations:
132 Sq. Mts
a) Reinforcement treatment coat
# Scrapping reinforcement with wire brush and cleaning the same from
all sides by light tapping, wire brushing and emery paper.
# applying Rusticide Rustprime/Ruskill A or approved equivalent in one
or more coats as directed as per manufacturers specification, washing
with water.
The rates quoted shall be inclusive of all the safety gadgets for the work-force such as Goggles, Hand-gloves, Helmets,
Suspending belts & hooks, aprons, shoes & boots etc complete for the work-force
The quoted rates for all the items mentioned hereinunder the BOQ for Internal Civil Restoration Works comprising of
various works to be executed shall be inclusive of the Demolition / Dismantaling / Shifting / Reshifting & Refixing of all the
existing items of the works duly mentioned & to be carried out and including all the areas where the works are to be
executed for proper working on site & compliance of all the activities on site including removal of debris from site on day to
day basis to avoid inconvinience to the residents / office of other organizations, stacking the same till the time of removal
at the desired location including carting away of debrirs at the designated PMC limits.
Flooring of all types, Tiles of any type, floor finishes, Wall dados, kerbs, Water-proofing, Brick bat coba, Walls, Brick
works, Platforms, Bunds, Stone work, Counters, tree guards, treads, risers etc, Concrete dismantling, mortar, RCC
elements, Steel, structural steel etc, Water-Proofing - All layers upto the level of bare slab including dressing the slab to
receive the new finishing material, Partitions of all types, Panelling of all types, Doors, Windows of all types, Steel work,
Frames, Grills etc, False Ceilings of all types, Wiring, Cables, Electrical fittings, fixtures, assessories, Cables, Wires,
Cable Trays, Lighting fittings & fixtures, Shifting of tables, chairs, furnitures items of all types, Air Conditioning units of all
types including assessories, Miscellaneous items such as Manure, Plants etc.
The above dismantling works are to be carried out upto the Terrace Floor level. The debris is to be carted outside the
premises and disposed off at the PMC designated place upto any lead. The serviceable and unserviceable materials
excluding debris shall be stacked properly in the designated place and to be secured in safe custody till the disposal of the
same. Sufficient manpower shall be provided for movement of furniture from one floor to other during execution.
The rates quoted shall be inclusive of Providing temporary plywood, 6mm thk covering to the existing openings / doors /
windows with temporary plywood before starting of the repair works including the removal of the same after completion of
the works. The rate shall be also inclusive of temporary wooden partitions, 6mm thk plywood with door shutters at the
desired locations, sealing joints with POP / masking tapes.
Sinature and Seal of the bidder Page43
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate (Rs.) Amount (Rs.)
b) Bond coat
# Providing & applying Polyalk Fixoprime or equivalent and Cement
(1:1.25) to exposed steel bars in two coats as per manufacturer's
specifications and brushable consistency for bonding old and new
concrete surfaces.
Providing and applying bonding coat of POLYALK EP or equivalent and
Cement (1: 1.25) to the entire concrete surface.
c) Mortar application
Applying Polymer modified mortar/concrete treatment as per
manufacturer's instructions in layers of thickness not exceeding 20 mm
(applying bonding coat at every layer) upto profile of concrete in the
vicinity by applying Hand pack Polymer Modified Mortar by mixing
1 part by weight of “POLYALK EP” or equivalent with
5 parts by weight of cement and
15 parts by weight of well graded sand and water to achieve the desired
consistency [Sand Grading IS383, Zone II, Silt content <6% ]
Including curing, scaffolding, cleaning etc. complete
Note:
If the depth of polymer modified mortar/concrete exceeds 50 mm, then
quantity shall be paid by considering multiplication factor = (actual
depth) / 50mm for additional thickness.
At a time apply mortar layer not more than 20 mm thick. The mortar
should be prepared using mechanical mixers / stirrers & should be well
compacted and finished using appropriate methods. The rate to include
for necessary compaction with mechanical plate vibrator etc. complete
to the satisfaction of the EIC.
3 CRACK FILLING WITH PMCM
Carefully removing the existing plaster / mortar / loose concrete,
chasing the cracks, including supplying, providing & errecting in
position the necessary scaffolding, disposal & cating away of the debris,
cleaning etc & sealing the separation cracks between R.C.C. and
brickwork by raking, open the crack by electrically operating groove
cutter as directed, insertion of 20 mm downgraded aggregates by
hammering as per the instructions of the consultant, sealing with
polymer modified cementatious mortar (25mm width x 25mm depth)
using Polyalk EP or equivalent as per the specification of item polymer
modified cementatious mortar/concrete, application of chicken mesh (
200mm wide, 200mm overlapping length) along the crack by 'U' nails
spaced at 300 mm c/c, including necessary breaking plaster, concrete,
brickwork, washing with water, curing, cleaning etc. complete
180 R.mt
4 Providing and repairing the damaged core portion of RCC columns by
superfluid micronconcrete incluidng mixing, transporting, placing
compacting, curing etc. complete but excluding reinforcement and
formwork. (Payment on the basis of actual consumption of Micro-
concrete)
565 Kgs
5 Grouting: Drill the holes of 12mm dia for depth upto 30mm inside the
damaged or hiney combed concrere area, at spacing as instructed by
consultants. Clean the holes by blast of air or by jet of water. Insert the
PVC nipples into pre drilled holes and seal peripherrally by "M Seal".
After 24, hours inject the polymer based stopper Cementaceous slurry
mix" in the proportion as under into the nipples, at a pressure of 2 kg/sq
cm using gum pumps of capacity not less than 30 PSI in the ratio of
(1kg polymer EP: 3KG cement: 2 litres of water). After two days of
curing, cut the nipples and seal it with polymer modified mortar.
583 Nos
Sinature and Seal of the bidder Page44
SHETGIRI and ASSOCIATES
S.No Description Qty. Unit Rate (Rs.) Amount (Rs.)
6 Column / Beam pre-wrap surface preparation by providing and appling
average upto 25mm thick reinfored Thixotropic Mortar over the uneven
RCC element surface including bonding coat, grinding the surface to
make round corners, covings,making the surface evenly smooth etc. as
per Manufacturer's instructions. (Measurement on the basis of finished
area)
15 Sq. Mts
7 Makeup lost steel area due to corrosion by providing additional steel
reinforcement. The steel shall confirm to IS 1786 grade Fe 415/ Fe 500.
Anchor the steel rebar in sound concrete body up to desired depth by
structural GRADE adhesive. Fixing of rebars is to be with pre left
binding wires with existing steel at regular grid after aligning concrete
profile with new mortar up to existing steel face.
120 Kgs
8 MEMBRANE COATING ON TERRACE FLOOR (MINIMUM
STIPULATION)
Providing and laying over the existing finishing of the terrace floors
which is repaied through the specifications as duly mentioned under the
Head Repair Works including projections, chajjas etc necessary
Polymer based Flexiroof PU or equivalent approved water-proofing
membrane treatment as additional coat treatment including injection
grouting to seal all cracks, crevices etc including final coat of cement
slurry as per manufacturers standards, specifications & execution
practices using approved chemicals of M/s BASF, Shieldtech, M/s
Sunanda Speciality Coatings Pvt Ltd or equivalent approved etc
complete as per manufacturers specifications, site instructions &
standard working procedures etc complete.
1353 Sq. Mts
9 ANTI-TERMITE TREATMENT TO THE PREMISES
Supplying Aldrex 30 E.C.of NOCIL or equivalent emulsifeable
concentrate confirming to IS-1307 at site & injecting the same with
dilution as per manufacturer's specification for post-constructional anti-
termite treatment and erecting a chemical barrier under / around the
column pits, walls, trenches, basements, excavation top surface of
plinth filling, exposed surfaces etc. as directed at site all complete.
1353 Sq. Mts
TOTAL OF INTERNAL CIVIL RESTORATION WORKS Rs.
SUM TOTAL OF SCHEDULE - CIVIL WORKS Rs.
Please Note : The rates quoted hereinabove shall be Exclusive of
GST and GST shall be additional at actuals.
SEAL AND SIGN OF BIDDER
Sinature and Seal of the bidder Page45
SHETGIRI AND ASSOCIATES
1.0 2.0 3.0 4.0 5.0 6.0 7.0
PART I - SCAFFOLDING
1 CPWD
Delhi
14.72/24
8
Providing and fixing double scaffolding system
(cup lock type) on the exterior side of
building/structure, up to 15 meter height, above
ground level, including additional rows of
scaffolding in stepped manner as per requirement
of site, made with 40mm dia M.S. tube, placed 1.5
meter centre to centre, horizontal & vertical tubes
joint with cup & lock system with M.S. Tubes, M.S.
tube challis, M.S. clamps and staircase system in
the scaffolding for working platform etc. and
maintaining it in a serviceable condition for
execution of work of cleaning and/ or pointing and/
or applying chemical and removing it thereafter.
The scaffolding system shall be stiffened with
bracings, runners, connecting with the building
etc, wherever required, if feasible, for inspection
of work at required locations with essential safety
features for the workmen etc., complete as per
directions and approval of Engineer-in-charge.
Note:- (1) The elevational area of the scaffolding
shall be measured for payment purpose. (2) The
payment will be made once only for execution of
all items for such works.
SqM. 1851.00
2 CPWD
Delhi
26.36/42
5
Providing, erecting, maintaining and removing
temporary protective screens made out of
specified fabric with all necessary fixing
arrangement to ensure that it remains in position
for the work duration as required by the Engineer-
in-charge.
26.36.1 Wooven PVC cloth SqM. 1851.00
INTERIOR RENOVATION WORK OF NABARD REGIONAL OFFICE AT 54, WELLESLEY ROAD, P.B.NO. 5,
SHIVAJI NAGAR, PUNE-411005
Sr.
No
Ref. /
Item No. Description Unit. Qty.
6. SCHEDULE - REPAIRS & RESTORATION WORKS
Rate (Rs.)Amount
(Rs.)
46 of 80
SHETGIRI AND ASSOCIATES
1.0 2.0 3.0 4.0 5.0 6.0 7.0
Sr.
No
Ref. /
Item No. Description Unit. Qty. Rate (Rs.)
Amount
(Rs.)
` PART - II - TEMPORARY PROPING
3 R.A 1 Propping and Supporting the structural members
and its adjoining areas with steel props
(adjustable as required), bracings, steel timber
runners etc. to relieve the structural member of
the required load coming over it as per the pattern
given by consultant and approved by Engineer-in-
charge complete.
Nos. 130.00
PART III - DISMENTALING/DEMOLISHING WORK
4 CPWD
Delhi/
15.56/
258
Dismantling old plaster or skirting raking out joints
and cleaning the surface for plaster including
disposal of rubbish to the dumping ground within
50 meters lead. SqM 1168.00
5 CPWD
Delhi
15.7/253
Demolishing brick work manually/ by mechanical
means including stacking of serviceable material
and disposal of unserviceable material within 50
meters lead as per direction of Engineer-in-
charge.
15.7.4 In cement mortar CuM 20.47
6 CPWD
Delhi
15.2/253
Demolishing cement concrete manually/ by
mechanical means including disposal of material
within 50 metres lead as per direction of Engineer -
in - charge.
15.2.1 Nominal concrete 1:3:6 or richer mix (i/c
equivalent design mix) CuM 36.00
7 CPWD
Delhi
15.5/253
Extra for cutting reinforcement bars manually/ by
mechanical means in R.C.C. or R.B. work
(Payment shall be made on the cross sectional
area of R.C.C. or R.B. work) as per direction of
Engineerin-charge. SqM 4.00
8 CPWD
Delhi
15.60/25
8
Disposal of building rubbish / malba / similar
unserviceable, dismantled waste materials by
mechanical means, including loading,
transporting, unloading to approved municipal
dumping ground or as approved by Engineer-in-
charge, beyond 50 m initial lead, for all leads
including all lift involved. CuM 172.00
47 of 80
SHETGIRI AND ASSOCIATES
1.0 2.0 3.0 4.0 5.0 6.0 7.0
Sr.
No
Ref. /
Item No. Description Unit. Qty. Rate (Rs.)
Amount
(Rs.)
PART - IV - STRUCTURAL REPAIRS
9 CPWD
Delhi -
26.28/42
3
Chipping of unsound/weak concrete material from
slabs, beams, columns etc. with manual Chisel
and/ or by standard power driven percussion type
or of approved make including tapering of all
edges, making square shoulders of cavities
including cleaning the exposed concrete surface
and reinforcement with wire brushes etc. and
disposal of debris for all lead and lifts all complete
as per direction of Engineer-In-Charge.
26.28.2 50mm average thickness SqM 338.00
10 CPWD -
26.29/42
3
Cleaning of reinforcement from rust from the
reinforcing bars to give it a total rust free steel
surface by using alkaline chemical rust remover of
approved make with paint brush and removing
loose particles after 24 hours of its application
with wire brush and thoroughly washing with water
and allowing it to dry, all complete as per direction
of Engineer-In-Charge.
26.29.1 Bars upto 12 mm diameter RMT 4584.00
26.29.2 Bars above 12 mm diameter RMT 936.00
11 CPWD
Delhi
5.22A/
100
Steel reinforcement for R.C.C. work including
straightening, cutting, bending, placing in position
and binding all complete above plinth level.
5.22A.6 Thermo-Mechanically Treated bars of grade Fe-
500 D or more. Kg. 13496.00
12 CPWD
Delhi
26.30/42
3
Drilling suitable holes in reinforced or plain
cement concrete with power driven drill machine
to a minimum depth of 100mm upto 200mm in
RCC beams, lintels, columns and slabs to
introduce steel bars for sunshades/balconies
including fixing the steel bars in position using
epoxy resin anchor grout of approved make but
excluding the cost of reinforcement, all complete
as per direction of Engineer-In-Charge.
26.30.1 Upto and including 12mm dia. Each 7602.00
13 CPWD
Delhi -
26.31/42
3
Providing, mixing and applying bonding coat of
approved adhesive on chipped portion of RCC as
per specifications and direction of Engineer-In-
charge complete in all respect.
26.31.2 Epoxy bonding adhesive having coverage 2.20
sqm/kg of approved make SqM 338.00
48 of 80
SHETGIRI AND ASSOCIATES
1.0 2.0 3.0 4.0 5.0 6.0 7.0
Sr.
No
Ref. /
Item No. Description Unit. Qty. Rate (Rs.)
Amount
(Rs.)
14 CPWD
Delhi -
26.32/42
4
Providing, mixing and applying SBR polymer (of
approved make) modified Cement mortar in
proportion of 1:4 (1 cement: 4 graded coarse sand
with polymer minimum 2% by wt. of cement used)
as per specifications and directions of Engineer-in-
charge. Note: Measurement and payment: The
pre-measurement of thickness shall be done just
after the surface preparation is completed and
Payment under this item shall be made only after
proper wet curing has been done and surface has
been satisfactorily evaluated by sounding /
tapping with a blunt metal instrument and/or the
75mm size cube crushing strength at the end of
28 days to be not less than 30 N/ mm2).
26.32.1 12 mm average thickness. SqM 477.00
15 CPWD
Delhi -
26.34/42
4
Providing and laying SBR Polymer modified (of
approved make @ minimum 2% by wt. of cement
used) plain/reinforced concrete jacket for the
structural members e.g. columns, pillars, piers,
beams etc with concrete having the specified
minimum characteristic compressive strength [with
ordinary portland cement, coarse sand and
graded stone aggregate of 10mm maximum size
in proportion as per design criteria] with specified
average thickness all-round existing core of RCC
member. Note: Rates shall be for finished surface
area of concrete and shall include the cost of
making holes in existing RCC slab, if required, for
pouring concrete in shuttering mould of jacket and
appropriate approved Super-Plasticiser for
rendering concrete as flowable self compacting
and SBR polymer but shall exclude cost of
reinforcement, bond coat, Shear Keys, centering
and shuttering, strutting, propping etc (Payment
under this item shall be made only after proper
wet curing has been done and surface has been
satisfactorily evaluated by sounding/tapping with a
blunt metal instrument).
26.34.2 75mm thick in Grade M 25 with cement content
not less than 330 kg per cum SqM 352.00
49 of 80
SHETGIRI AND ASSOCIATES
1.0 2.0 3.0 4.0 5.0 6.0 7.0
Sr.
No
Ref. /
Item No. Description Unit. Qty. Rate (Rs.)
Amount
(Rs.)
16 CPWD
26.35/42
5
Providing and injecting approved grout in
proportion recommended by the manufacturer into
cracks/honey-comb area of concrete/ masonry by
suitable gun/pump at required pressure including
cutting of nipples after curing etc. complete as per
directions of Engineerin-Charge. (The payment
shall be made on the basis of actual weight of
approved grout injected.)
26.35.1 Stirrer mixed Acrylic Polymer of approved make
@ 2% of weight of cement used) modified Cement
slurry made with non shrink compound in
concrete/RCC work Kg. 85.00
26.35.3 Epoxy injection grout in concrete/RCC work of
approved make Kg. 34.00
17 CPWD
Delhi -
26.37/42
4
Cleaning of exposed concrete surface of sticking
material including loose and foreign material by
sand blasting with coarse sand followed by and
including cleaning with oil free air blast as per
direction of Engineer in charge.SqM 338.00
18 CPWD
Delhi -
26.38/42
4
Shotcreting R.C.C. columns, beams and slabs
etc. in layers with approved design mix concrete
having the specified minimum characteristic
compressive strength [with ordinary portland
cement, coarse sand and graded stone aggregate
of 10 mm maximum size in proportion as per
design criteria] including the cost of centering and
shuttering at edges and corners etc. as directed
by Engineer-in-Charge. Note: Rates shall include
the providing necessary ground wires etc. The
levelling gauges, if used, shall be paid for
separately. Payment under this item shall be
made only after proper wet curing has been done
and surface has been satisfactorily evaluated by
sounding/tapping with a blunt metal instrument.
26.38.1 25mm thick in Grade M 25 with cement content
not less than 330 kg per cum SqM 11.00
26.38.2 50mm thick in Grade M 25 with cement content
not less than 330 kg per cum SqM 1006.00
26.38.3 75mm thick in Grade M 25 with cement content
not less than 330 kg per cum SqM 11.00
50 of 80
SHETGIRI AND ASSOCIATES
1.0 2.0 3.0 4.0 5.0 6.0 7.0
Sr.
No
Ref. /
Item No. Description Unit. Qty. Rate (Rs.)
Amount
(Rs.)
19 CPWD
Delhi
26.39/42
6
Providing and inserting 12mm dia galvanised steel
injection nipple in honey comb area and along
crack line including drilling of holes of required
diametre (20mm to 30mm) up to depth from 30mm
to 80mm at required spacing and making the hole
& crack dust free by blowing compressed air,
sealing the distance between injection nipple with
adhesive chemical of approved make and allow it
to cure complete as per direction of Engineer-In-
Charge.
Each 360.00
PART - V - WATER PROOFING
20 State e-
DSR 17-
18 /
31.09 /
BDJ /
171
Providing and applying water proofing treatment
using acrylic polymer modified cement based
water proofing coating with fibre glass mesh
mixing at the rate of powder to liquid (2:1) by
weight covering 9 to 10 sqm /kg with two coat
using Dr. Fixit or alike of chemicals for masonry
and concrete surface by brush covering 7 years
guarantee on Stamp Papers etc. complete.
SqM 359.00
21 CPWD
Delhi
14.82/
250
Dismantling W.C. Pan of all sizes including
disposal of dismantled materials i/c malba all
complete as per directions of Engineer-in-
Charge. Each 32.00
22 CPWD
Delhi
22.5/ 382
Providing and laying water proofing treatment in
sunken portion of WCs, bathroom etc., by
applying cement slurry mixed with water proofing
cement compound consisting of applying : (a)
First layer of slurry of cement @ 0.488 kg/sqm
mixed with water proofing cement compound @
0.253 kg/ sqm. This layer will be allowed to air
cure for 4 hours. (b) Second layer of slurry of
cement @ 0.242 kg/sqm mixed with water
proofing cement compound @ 0.126 kg/sqm. This
layer will be allowed to air cure for 4 hours
followed with water curing for 48 hours. The rate
includes preparation of surface, treatment and
sealing of all joints, corners, junctions of pipes
and masonry with polymer mixed slurry.
SqM 160.00
51 of 80
SHETGIRI AND ASSOCIATES
1.0 2.0 3.0 4.0 5.0 6.0 7.0
Sr.
No
Ref. /
Item No. Description Unit. Qty. Rate (Rs.)
Amount
(Rs.)
PART - VI - CIVIL WORK
23 CPWD
Delhi
4.1/ 88
Providing and laying in position cement concrete
of specified grade excluding the cost of centering
and shuttering - All work up to plinth level :
4.1.6 1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6
graded stone aggregate 40 mm nominal size). CuM 36.00
24 CPWD
Delhi
5.3/ 97
Reinforced cement concrete work in beams,
suspended floors, roofs having slope up to 15°
landings, balconies, shelves, chajjas, lintels,
bands, plain window sills, staircases and spiral
stair cases above plinth level up to floor five level,
excluding the cost of centering, shuttering,
finishing and reinforcement, with 1:1.5:3 (1
cement : 1.5 coarse sand (zone-III) : 3 graded
stone aggregate 20 mm nominal size).
CuM 10.00
25 CPWD
Delhi
10.1/ 182
Structural steel work in single section, fixed with
or without connecting plate, including cutting,
hoisting, fixing in position and applying a priming
coat of approved steel primer all complete.
Kg. 1000.00
26 CPWD
Delhi
6.3/111
Brick work with common burnt clay machine
moulded perforated bricks of class designation
12.5 conforming to IS: 2222 in superstructure
above plinth level up to floor five level in cement
mortar 1:6 (1 cement : 6 coarse sand) :
6.3.2 With Modular bricks CuM 21.00
27 CPWD
Delhi
13.11/
228
18 mm cement plaster in two coats under layer 12
mm thick cement plaster 1:5 (1 cement : 5 coarse
sand) finished with a top layer 6 mm thick cement
plaster 1:6 (1 cement : 6 fine sand).
SqM 64.80
28 CPWD
Delhi
13.1/216
Cement plaster (in fine sand)
A 13.1.1 1:4 ( 1 Cement : 4 fine sand ) SqM 170.00
29 CPWD
Delhi
14.1/242
Repairs to plaster of thickness 12 mm to 20 mm in
patches of area 2.5 sq. meters and under,
including cutting the patch in proper shape, raking
out joints and preparing and plastering the surface
of the walls complete, including disposal of
rubbish to the dumping ground, all complete as
per directions of Engineer-In-Charge.
14.1.1 With cement mortar 1:4 (1 cement : 4 fine sand)
SqM
361.80
52 of 80
SHETGIRI AND ASSOCIATES
1.0 2.0 3.0 4.0 5.0 6.0 7.0
Sr.
No
Ref. /
Item No. Description Unit. Qty. Rate (Rs.)
Amount
(Rs.)
PART - VII - PLUMBING WORK
30 CPWD
Delhi
12.41/
213
Providing and fixing on wall face unplasticised
Rigid PVC rain water pipes conforming to IS :
13592 Type A, including jointing with seal ring
conforming to IS : 5382, leaving 10 mm gap for
thermal expansion, (i) Single socketed pipes.
12.41.2 110 mm diameter RMT 270.00
31 CPWD
Delhi
12.42/
214
Providing and fixing on wall face unplasticised -
PVC moulded fittings/ accessories for
unplasticised Rigid PVC rain water pipes
conforming to IS : 13592 Type A, including jointing
with seal ring conforming to IS : 5382, leaving 10
mm gap for thermal expansion.
12.42.1 Coupler
12.42.1.2 110 mm Each 75.00
12.42.4 Single tee without door
12.42.4.2 110 X 110 X 110 MM Each 15.00
12.42.6 Shoe (plain)
12.42.6.2 110 mm Shoe Each 15.00
32 CPWD
Delhi
12.43/
214
Providing and fixing unplasticised -PVC pipe clips
of approved design to unplasticised - PVC rain
water pipes by means of 50x50x50 mm hard wood
plugs, screwed with M.S. screws of required
length, including cutting brick work and fixing in
cement mortar 1:4 (1 cement : 4 coarse sand) and
making good the wall etc. complete.
12.43.2 110 mm Each 290.00
Rs.
SEAL AND SIGN OF BIDDER
SUM TOTAL OF SCHEDULE - FURNITURE WORKS
Please Note : The rates quoted hereinabove shall be
Exclusive of GST and GST shall be additional at actuals.
53 of 80
M/s. Shetgiri Associates
S.NO PARTICULARS QTY UNIT RATE (Rs.) AMOUNT (Rs.)
I ELECTRICAL WORKS
A
1
Suply and installation of 4-way, PPI TPN, Double Door, Metal type, with Plain /
Transperant Door (As approved by client / consultant / architect), Lighting
Distribution Board (LDB), surface / flush mounted on wall, interconnected wiring
complete with earthing lugs, including DB wiring dressing with ferruling, termination of
circuits with ping type copper lugs, blank plates, etc. housing following switchgears :
(Schneider / Hager / Siemens / Legrand or any other equivallent make as approved by
client / Architect)
(Note :- DB size & type selection shall be done with reference to the total number of
modules / poles available in the DB which shall be suitable for housing of below
mentioned switchgears & components forming a complete set.)
a 1 no., 63/40A, FP MCB, "C" curve type as incomer
b 3 no.s, 25A, DP RCCB with sensitivity of 100mA, as sub-incomer
c9 nos, 10/16A, SP, MCB, "C" curve type as outgoings + 3 no.s 1M-RYB indicators /
lamps each.
Full Set as above 2.00 Nos
2
Suply and installation of 6-way, PPI TPN, Double Door, Metal type, with Plain /
Transperant Door (As approved by client / consultant / architect), Lighting
Distribution Board (LDB), surface / flush mounted on wall, interconnected wiring
complete with earthing lugs, including DB wiring dressing with ferruling, termination of
circuits with ping type copper lugs, blank plates, etc. housing following switchgears :
(Schneider / Hager / Siemens / Legrand or any other equivallent make as approved by
client / architect)
(Note :- DB size & type selection shall be done with reference to the total number of
modules / poles available in the DB which shall be suitable for housing of below
mentioned switchgears & components forming a complete set.)
a 1 no., 63/40A, FP MCB, "C" curve type as incomer
b 3 no.s, 25A, DP RCCB with sensitivity of 100mA, as sub-incomer
c15 nos, 10/16A, SP, MCB, "C" curve type as outgoings + 3 no.s 1M-RYB indicators /
lamps each.
Full Set as above 2.00 Nos
3
Suply and installation of 4-way, TPN, Double Door, Metal type, with Plain /
Transperant Door (As approved by client / consultant / architect), Raw Power / AC
Power Distribution Board (RPDB / ACPDB), surface / flush mounted on wall,
interconnected wiring complete with earthing lugs, including DB wiring dressing with
ferruling, termination of circuits with ping type copper lugs, blank plates, etc. housing
following switchgears : (Schneider / Hager / Siemens / Legrand or any other equivallent
make as approved by client / architect)
(Note :- DB size & type selection shall be done with reference to the total number of
modules / poles available in the DB which shall be suitable for housing of below
mentioned switchgears & components forming a complete set.)
a 1 no., 63/40A, FP MCB, "C" curve type as incomer
b9 nos, 16/25A, SP, MCB, "C" curve type as outgoings + 3 no.s 1M-RYB indicators /
lamps each.
Full Set as above 4.00 Nos
4
Suply and installation of 6-way, TPN, Double Door, Metal type, with Plain /
Transperant Door (As approved by client / consultant / architect), Raw Power / AC
Power Distribution Board (RPDB / ACPDB), surface / flush mounted on wall,
interconnected wiring complete with earthing lugs, including DB wiring dressing with
ferruling, termination of circuits with ping type copper lugs, blank plates, etc. housing
following switchgears : (Schneider / Hager / Siemens / Legrand or any other equivallent
make as approved by client / architect)
(Note :- DB size & type selection shall be done with reference to the total number of
modules / poles available in the DB which shall be suitable for housing of below
mentioned switchgears & components forming a complete set.)
a 1 no., 63/40A, FP MCB, "C" curve type as incomer
b15 nos, 10/16/25/32A, SP, MCB, "C" curve type as outgoings + 3 no.s 1M-RYB
indicators / lamps each.
Full Set as above 4.00 Nos
ELECTRICAL INSTALLATION WORKS NABARD REGIONAL OFFICE AT 54, WELLESLEY ROAD, P.B.NO. 5, SHIVAJI NAGAR,
PUNE-411005
7. BILL OF QUANTITIES FOR ELECTRICAL AND ALLIED WORKS
ELECTRICAL BOQ Page 54 of 80
M/s. Shetgiri Associates
S.NO PARTICULARS QTY UNIT RATE (Rs.) AMOUNT (Rs.)
5
Suply and installation of 8-way, TPN, Double Door, Metal type, with Plain /
Transperant Door (As approved by client / consultant / architect), Raw Power / AC
Power Distribution Board (RPDB / ACPDB), surface / flush mounted on wall,
interconnected wiring complete with earthing lugs, including DB wiring dressing with
ferruling, termination of circuits with ping type copper lugs, blank plates, etc. housing
following switchgears : (Schneider / Hager / Siemens / Legrand or any other equivallent
make as approved by client /architect)
(Note :- DB size & type selection shall be done with reference to the total number of
modules / poles available in the DB which shall be suitable for housing of below
mentioned switchgears & components forming a complete set.)
a 1 no., 63/40A, FP MCB, "C" curve type as incomer
b21 nos, 10/16/25/32A, SP, MCB, "C" curve type as outgoings + 3 no.s 1M-RYB
indicators / lamps each.
Full Set as above 4.00 Nos
6
Suply and installation of 6-way, TPN, Double Door, Metal type, with Plain /
Transperant Door (As approved by client / consultant / architect), Main UPS
Power Distribution Board (UPS PDB), surface / flush mounted on wall,
interconnected wiring complete with earthing lugs, including DB wiring dressing with
ferruling, termination of circuits with ping type copper lugs, blank plates, etc. housing
following switchgears : (Schneider / Hager / Siemens / Legrand or any other equivallent
make as approved by client /architect)
a 1 no., 63A, FP MCB, "C" curve type as incomer
b 18 nos, 16/20A, SP, MCB, "C" curve type as outgoings
Full Set as above 4.00 Nos
7
Suply and installation of 8-way, SPN, Double Door, Metal type, with Plain /
Transperant Door (As approved by client / consultant / architect), RAW / UPS
Power Distribution Board / Main Emergency Lighting Power Distribution Board
(RPDB / UPSDB / EMG LDB), surface / flush mounted on wall, interconnected wiring
complete with earthing lugs, including DB wiring dressing with ferruling, termination of
circuits with ping type copper lugs, blank plates, etc. housing following switchgears :
(Schneider / Hager / Siemens / Legrand or any other equivallent make as approved by
client /architect)
a 1 no., 40/32A, DP MCB, "C" curve type as incomer
b 6 nos, 16/20/25A, SP, MCB, "C" curve type as outgoings
Full Set as above 4.00 Nos
TOTAL of SECTION (A) RS.
B CABELS / MAINS
1
Supply & Installation of 1100V grade armoured cable having sector / circular shaped
aluminium / copper conductor PVC insulated cores, laid up, PVC tape wrappe d inner
sheathed, GI strip / wire armoured and overall extruded PVC sheathed confirming to
IS: 1554, laid on wall / ceiling using GI clamps & spacers / underground at necessary
depth as required as per site conditions & as per route shown / approved at site and
further as directed by Consultant / Client at site in the following sizes :- (Make - Polycab
/ Finolex / CCI / RR / Havells or any other equivallent make as approved by client
/architect)
NOTE :- All Armoured cables shall be provided with temporary labelling at every
5mtrs & then finally with metal indentification tags showing the size & the
location from/to the respective Panel / DB, at both the ends.
1.1 4C x 16 Sq.mm Copper Armoured cable with 2 runs of 12 SWG GI bare wire 400.00 Mtrs
1.2 4C x 10 Sq.mm Copper Armoured cable with 2 runs of 12 SWG GI bare wire 800.00 Mtrs
1.3 3C x 6 Sq.mm Copper Armoured cable 15.00 Mtrs
2
GLANDING & TERMINATION :- Supply & Installation of end termination of above
mentioned cables including compressed type brass glands, crimping type copper
lugs, insulation tape etc. as 'required complete with earthing of glands in following sizes
:-
2.1 4C x 16 Sq.mm Copper Armoured cable 16.00 Nos
2.2 4C x 10 Sq.mm Copper Armoured cable 16.00 Nos
3
GLANDING & TERMINATION :- Supply & Installation of end termination of below
mentioned cables sizes including heavy guage PVC type glands, crimping type
copper lugs, insulation tape etc. as 'required complete with all necessary hardware &
accessories, etc. in following sizes :-
3.1 4C x 16 Sq.mm Copper Armoured Cable 15.00 Nos
3.2 4C x 10 Sq.mm Copper Armoured Cable 3.00 Nos
3.3 4C x 6 Sq.mm Copper Armoured Cable 3.00 Nos
3C x 4 Sq.mm Copper Armoured cable 10.00
TOTAL of SECTION (B) RS.
ELECTRICAL BOQ Page 55 of 80
M/s. Shetgiri Associates
S.NO PARTICULARS QTY UNIT RATE (Rs.) AMOUNT (Rs.)
C INTERNAL LIGHTING & POWER WIRING
1
Supply & Installation of concealed / ressessed / surface light point / ceiling fan point /
call bell point wiring using 600V FRLS conductor grade 3R (P+N+E) x 1.5 Sq.mm
copper conductor PVC insulated wires (with proper R,Y,B color code) pulled through in
appropriate size 20/25mm dia of 16 SWG wall thickness, MS/ medium conduits, ISI
mark, laid concealed over false ceiling or in wall chases or on the ceiling in case of an
open ceiling including 3R (P+N+E) x 2.5 Sq.mm circuit wires from the relevant DB and
also including 2.5 sqmm green color copper earth wire and approved make modular
type switch plate, switches, MS concealed back box, etc. as required & as approved by
the consultant. Metal Flexible conduit use it must be joined by gland and check nut at
both ends. (Each circuit shall not feed more than 8 points OR 800 watts as per
following configuration.) (The item rate shall include Lighting / Raw / UPS Power Circuit
wiring from relevent DB to the switch board with 3Rx2.5 Sq.mm FRLS wires & from
switch board to next switch board OR to the first light point / primary point / full point)
NOTE :- 1. Only FRLS wire shall be used; 2. Conduit carrying circuit wiring should not
carry point wiring and Conduit carrying point wiring should not carry submain/circuit
wiring; 3. Flexible conduits & Elbows are not allowed; 4. The wires from ceiling junction
to light points / light fixture shall be drawn in flexible Metal conduit with adptor & cover
for junction box & crimp type lugs at both the ends alongwith necessary hardware &
accessories, etc. as required; 5. Proper ferrules, lugs, must be used in all cabling and
wiring on both load / source end; 6. Each switch board must be provided with
respective ferrules representing the respective DB, Phase & Circuit numbers; 7.
Looping of Neutral / Earth wire between two seperate Primary / Full Points is strictly not
allowed; 8. Looping of Neutral / Earth wire between two seperate circuits on similar or
other phase is strictly not allowed; 9. Ferulling / numbering / taggning to wires with
circuit number & db name for all lighting & raw / ups power shall be strictly followed at
both DB & switch board / switch socket boards ends.
1.1
Primary light points including the cost of 5A switch (Note :- Light Points which are
controlled by Occupancy / Movement / Dual Channel Sensors, the wiring shall be
routed through the respective sensor as required.)
30.00 Nos
1.2
Primary light points directly taken / operated from LDB but excluding the cost of MCB.
(Note :- Light Points which are controlled by Occupancy / Movement / Presence
Sensors, the wiring shall be routed through the respective sensor as required.)10.00 Nos
1.3 Secondary light points looped from the above point 60.00 Nos
1.4 Two way light point including the cost of 5A two way switch 12.00 Nos
1.5
Fan Point including 120W Electronic type step regulator, anchor fastner & 'S' type fan
hook in ceiling to suspend ceiling fan by cutting / chiesling / painting as required 5.00 Nos
1.6
Service Call Bell point (For Cabin / Room) comprising of wiring as above including the
cost of audio visual indicator electronic bell buzzer installed at single common location
in kitchen / attendent room as approved by the Architect / Client / Consultant.25.00 Nos
1.7Bell point comprising of wiring as above including G-Magic Wireless Door Bell 4061
with Remote, 32-Melodies & Flashing Light.16.00 Nos
1.8
5A plug point as primary point independent mounted on wall / partition / on work
station, etc. (UPS / RAW Power) (Only five workstations / independent mounted raw
power points shall be looped in one raw power circuit. Whereas in measurements out
of five workstations / independent mounted, four no.s of 5A s/s raw points will be
considered as secondary points & 1 no. of 5A s/s raw point will be considered as
primary point.)
90.00 Nos
1.9
Secondary 5A Plug point on switch board or looped from above 5A primary point (UPS
/ RAW Power) (Only five workstations / independent mounted raw power points shall
be looped in one raw power circuit. Whereas in measurements out of five workstations
/ independent mounted, four no.s of 5A s/s raw points will be considered as secondary
points & 1 no. of 5A s/s raw point will be considered as primary point.)
175.00 Nos
2Exhaust fan point consisting of 5A socket near fan and switch on light switch board
32.00 Nos
3
Supply & installation of 5/15A Plug Point directly taken from DB as a Primary Plug Point
for Pantry / geyser / zerox / printer / fridge, etc. including 2 x 4 Sq.mm FRLS
conductor grade circuit wires directly taken from the relevant DB and also including
2.5 sqmm green color copper earth wire all laid through MS conduit with all necessary
hardware& accessories, etc. (UPS / Raw Power)
32.00 Nos
4
Supply & installation of 5/15A Plug Point as secondary Plug Point directly taken /
looped from above Primary 5/15A Plug point for Pantry / geyser / zerox / printer / fridge,
etc. including 2 x 2.5 sqmm FRLS conductor grade circuit wires directly taken from the
relevant DB and also including 2.5 sqmm green color copper earth wire all laid through
MS conduit with all necessary hardware& accessories, etc. (UPS / Raw Power)
96.00 Nos
ELECTRICAL BOQ Page 56 of 80
M/s. Shetgiri Associates
S.NO PARTICULARS QTY UNIT RATE (Rs.) AMOUNT (Rs.)
5
Supply & Installation of point wiring for UPS or stabilized power plug points on
workstations / table for computers using 3C X2.5 Sqmm FRLS conductor grade
copper conductor PVC sheathed white color flexible cable pulled through already laid
floor raceways and taken upto table top using Metal flexible conduits run within
wooden/metal partitions. Each point consisting of 4 nos of 5A , 2/3 pin sockets
below table top & 1 No., 15A Switch above table top, wired together forming one
point. The earth wire of 3 core flexible cable to be of yellow-green color only.
(ONLY FOUR tables served by one circiut from DB)
50.00 Nos
6
Supply & Installation of point wiring for UPS or stabilized power plug points on
workstations / table for computers using 3C X2.5 Sqmm FRLS conductor grade copper
conductor PVC sheathed white color flexible cable pulled through already laid floor
raceways and taken upto table top using Metal flexible conduits run within
wooden/metal partitions. Each point consisting of 3 nos of 5A , 2/3 pin sockets below
table top & 1 No., 15A Switch above table top, wired together forming one point. The
earth wire of 3 core flexible cable to be of yellow-green color only. (ONLY FOUR
tables served by one circiut from DB)
225.00 Nos
7
Supply & Installation of point wiring for UPS or stabilized power plug points on
workstations / table for computers using 3C X2.5 Sqmm FRLS conductor grade
copper conductor PVC sheathed white color flexible cable pulled through already laid
floor raceways and taken upto table top using Metal flexible conduits run within
wooden/metal partitions. Each point consisting of 2 nos of 5A , 2/3 pin sockets & 1
No., 15A Switch , wired together forming one point. The earth wire of 3 core flexible
cable to be of yellow-green color only. (ONLY FOUR tables served by one circiut from
DB)
70.00 Nos
8
Supply & Installation of TV socket outlet point including approved make modular
switchboard / in the existing switch board including all the necessary hardware &
accessories, etc.
22.00 Nos
9Supply & Installation of RG6 TV cable with MS conduit, Medium gauge, 1.6 mm thick,
ISI Mark, with necessary hardware & accessories etc.2050.00 Rmt.
10Supply & Installation of RG11 TV cable with MS conduit, Medium gauge, 1.6 mm thick,
ISI Mark, with necessary hardware & accessories etc.576.00 Rmt.
11Supply & installation of 2-way splitter junction box including all necessary hardware,
accessories, etc.15.00 Nos
12Supply & installation of 4-way splitter junction box including all necessary hardware,
accessories, etc.16.00 Nos
TOTAL of SECTION (C) RS.
ELECTRICAL BOQ Page 57 of 80
M/s. Shetgiri Associates
S.NO PARTICULARS QTY UNIT RATE (Rs.) AMOUNT (Rs.)
D TRENCHING / FLOOR -RACEWAYS
1
Supply and laying Raceways / MS Conduits (for under floor trenches / On trays) on
existing flooring. Raceways / MS conduits shall be fixed to the flooring with GI clamps
for finished levels as per the site conditions or through partitions with all accessories.
The rate shall include preparation of trenches of required sizes by carefully removing
the malwa on existing floor for laying Raceways/conduits for power, data, telephone
cables etc. The depth of the trenches shall be at least 2 inches from the finished floor
level or upto RCC of the slab. The rate shall include the cost of the
Raceways/conduits. The rate shall also include the activity of clearing the debris
generated from the preparation of trenches & filling the same with PCC. (FOR THE
PORTION WITHOUT FALSE FLOORING)
1.1 100 x 40 x 1.6mm thick Aluminium Raceways 375.00 Mtrs
1.2 80 x 40 x 1.6mm thick Aluminium Raceways 590.00 Mtrs
1.3 60 x 40 x 1.6mm thick Aluminium Raceways 1250.00 Mtrs
1.432 mm HMS heavy guage, PVC conduit to be laid concelled / surface in / on wall / floor
as required as per the above mentioned specifications890.00 Mtrs
1.525 mm HMS heavy guage, PVC conduit to be laid concelled / surface in / on wall / floor
as required as per the above mentioned specifications575.00 Mtrs
2
Supply & Installation of floor junction boxes without top cover for above raceways, of
following sizes, fabricated out of M.S. sheets, fully powder coated with provision for
removable M.S. / S.S. screwed cover plates on all four sides for blocking the entry
into the junction box. All the junction boxes to be (with stud) 'properly earth - bonded
with the raceways pipe using 12 SWG Copper bare wire as directed at site.
2.1 Junction Box of size (250mm x 250mm x 50mm x 2.5mm thick) 65.00 Nos
2.2 Junction Box of size (300mm x 300mm x 50mm x 2.5mm thick) 150.00 Nos
2.3 Junction Box of size (350mm x 350mm x 50mm x 2.5mm thick) 40.00 Nos
2.4 Junction Box of size (400mm x 400mm x 50mm x 2.5mm thick) 16.00 Nos
3
Supply & Installation of suitable sizes 2mm thick removable cover plate screwed on
all four sides of M.S. sheet, fully powder coated, for blocking the entry into the floor
junction box for following sizes of junction boxes with rounded corners as per the
instruction given & sample approved by the client / architect / consultant at site. Cover
plate shall have required no.s of 1' dia knockouts for flexible conduit outlets as per the
requirement.
3.1 for Junction Box of size (250mm x 250mm x 50mm x 2.5mm thick) 10.00 Nos
3.2 for Junction Box of size (300mm x 300mm x 50mm x 2.5mm thick) 75.00 Nos
3.3 for Junction Box of size (350mm x 350mm x 50mm x 2.5mm thick) 11.00 Nos
3.4 for Junction Box of size (400mm x 400mm x 50mm x 2.5mm thick) 45.00 Nos
4
Supply & Installation of suitable sizes 2mm thick removable cover plate screwed on
all four sides of S.S. sheet, for blocking the entry into the floor junction box for following
sizes of junction boxes with rounded corners as per the instruction given & sample
approved by the client / architect / consultant at site. Cover plate shall have required
no.s of 1' dia knockouts for flexible conduit outlets as per the requirement.
4.1 for Junction Box of size (250mm x 250mm x 50mm x 2.5mm thick) 55.00 Nos
4.2 for Junction Box of size (300mm x 300mm x 50mm x 2.5mm thick) 75.00 Nos
4.3 for Junction Box of size (350mm x 350mm x 50mm x 2.5mm thick) 29.00 Nos
5
Supplying & fixing of 2mm thick G.I. Perforated type cable Trays of Asian /Profab
Engieers approved make. The cable tray shall be fixed to the ceiling / wall with MS
angle support with 35mmx2mm thick GI slotted 'C' channel patti at an interval of 1
meter or the MS angle iron fabricated support depending upon the location. The rate
shall include the cost of Supports, hardware & accessories, etc. complete as required.
5.1 Cable Tray :- 150 mm wide x 50 mm height x 2mm thick. 135.00 Mtrs
5.2 Cable Tray :- 300 mm wide x 300 mm height x 2mm thick. 225.00 Mtrs
6
Providing necessary opening within slab by mechanical drill of approximate size (600W
x 150D)mm without disturbing the existing reinforcement and making it good with
concrete after laying of necessary armoured cables, cable tray, channels, conduits, etc.
& clearing the site complete including all neccessary hardware and accessories,etc.
0 Nos
TOTAL of SECTION (D) RS.
ELECTRICAL BOQ Page 58 of 80
M/s. Shetgiri Associates
S.NO PARTICULARS QTY UNIT RATE (Rs.) AMOUNT (Rs.)
E LIGHTING FIXTURES & LIGHTING CONTROLS
Supply & Installation of lighting fixtures with lamps as per the details below including
necessary hardware such as clamps, nuts, bolts, nails, screws and suspension rods as
required for fixing the fixtures in position as directed by architect / consultant / client.
All Light Fixtures excluding Fans, Exhaust Fans & other fittings samples shall be
approved by the Client / Architect / Consultant before placing order to the respective
Vendor / Supplier. All Light Fixtures shall be of GE / Philips / CGL / Osram (For LED
Flexible Strip Only) make only unless & otherwise other makes are specified. Client /
Architect / Consultant reserves right to approve / select final Light Fitxtures from any
make as required.
1 LED Type Light fixture suitable for Modular Ceiling
1.1
Supply & Installation of (30-40W) (2' X 2') LED Mirror optic Light fixture. The fitting shall
be surface mounted / to be hanged from the ceiling at the height approved by architect.
(GE Cat No. :- Maple GCR030.56 or equivalent category & model in Philips / CGL or
any other equivallent make as approved by client /architect)
8.00 Nos
2 LED Type Light fixture suitable for Modular Ceiling
2.1
Supply & Installation of (15-18 W) LED Spotlight flush mounted Light fixture. (GE Cat
No. :- GE FERN LG7 18W GDR018.56L2 or equivalent category & model in Philips /
CGL or any other equivallent make as approved by client /architect)
7.00 Nos
2.2
Supply & Installation of (10-15 W) LED Spotlight flush mounted Light fixture. (GE Cat
No. :- GE FERN LG7 12W GDR012.56L2 or equivalent category & model in Philips /
CGL or any other equivallent make as approved by client /architect.)
5.00 Nos
2.3
Supply & Installation of (6/7W) LED Spotlight fixed / eye ball rotating type as approved
flush mounted Light fixture. (GE / PHILIPS / CGL or any other equivallent make as
approved by client /architect)
1.00 Nos
2.4
Supply & Installation of (3W) LED Spotlight fixed / eye ball rotating type as approved
flush mounted Light fixture. (GE / PHILIPS / CGL or any other equivallent make as
approved by client /architect)
8.00 Nos
2.5
Supply & Installation of (1W) LED Spotlight fixed / eye ball rotating type as approved
flush mounted Light fixture. (GE / PHILIPS / CGLor any other equivallent make as
approved by client /architect)
7.00 Nos
3 LED Type Light fixture suitable for bare Ceiling / Surface mounted
3.2
Supply & Installation of (15-18 W) LED Spotlight surface mounted Light fixture. (GE /
PHILIPS / CGLor any other equivallent make as approved by client /architect) 1.00 Nos
3.3
Supply & Installation of (10-15 W) LED Spotlight surface mounted Light fixture. (GE /
PHILIPS / CGL or any other equivallent make as approved by client /architect) 1.00 Nos
4 Cove / Indirect Lighting & Other Area Lighting
4.1
Supply & Installation of color changing Indoor type flexible LED strip light including
required rated driver / power supply in multiples of 1 Rmtr as approved by the architect
/ consultant / client along with all necessary hardware & accessories, etc. complete as
required (PHILIPS / WIPRO / CGL / GE or any other equivallent make as approved by
client /architect).
140.00 Rmt
4.2Supply & Installation of IR Remote suitable for control of color changing flexible LED
strip lighting6.00 Nos
4.3
Supply & Installation of single color (warm white 2800k light / any other approved color)
Indoor type flexible LED strip light including required rated driver / power supply in
multiples of 1 Rmtr as approved by the architect / consultant / client along with all
necessary hardware & accessories, etc. complete as required (PHILIPS / WIPRO /
CGL / GEor any other equivallent make as approved by client /architect).
150.00 Rmt
4.4 Supply & Installation of 7/9w LED bracket/mirror light. (PHILIPS / CG / GE make) 8.00 Nos
4.5
Supply & Installation of (20/18W) 4'/1200mm Decorative Slim LED Tubelight. The
fitting shall be surface mounted on wall / to be hanged from the ceiling at the height
approved by architect / client / consultant.
8.00 Nos
4.6Supply & Installation of (20/22W) (4') LED Tubelight. (Philips Cat No. - BN021 LED
20S or or any other equivallent model & make as approved by client /architect)50.00 Nos
4.7Supply & Installation of (10/12W) (2') LED Tubelight. (Philips / CG / GE / Bajaj or any
other equivallent make as approved by client /architect)10.00 Nos
4.8
Supply & Installation of (10/8W) 2'/600 Decorative Slim LED Tubelight. The fitting shall
be surface mounted on wall / to be hanged from the ceiling at the height approved by
architect / client / consultant.
2.00 Nos
ELECTRICAL BOQ Page 59 of 80
M/s. Shetgiri Associates
S.NO PARTICULARS QTY UNIT RATE (Rs.) AMOUNT (Rs.)
5 Decorative Lighting (Only for Reception Area)
5.1
Supply & Installation of Decorative type (Chandelier) Light fixtures (LED type
preferably) only for Reception Area (Total = 1 no.s). Basic cost of per light fitting
including lamp shall be not be more than Rs. 50,000/- (Inclusive of all taxes,
duties, etc.). The fitting shall be hanged from the ceiling at the required height
alongwith required support arrangements from the ceiling including all neecessary
hardware & accessories, etc. complete as required, directed & approved by the
Architect / Client / Consultant. (For Reception Area Only) (Rate shall be quoted as
one JOB Lumpsum basis only.)
1.00 LS
5.2
Supply & Installation of Decorative type (Chandelier) Light fixtures (LED type
preferably) only for Cabin. Basic cost of per light fitting including lamp shall be
not be more than Rs. 25,000/- (Inclusive of all taxes, duties, etc.). The fitting shall
be hanged from the ceiling at the required height alongwith required support
arrangements from the ceiling including all neecessary hardware & accessories, etc.
complete as required, directed & approved by the Architect / Client / Consultant. (For
Cabin Only) (Rate shall be quoted as one JOB Lumpsum basis only.)
5.00 LS
6 Fans & Exhaust Fans
6.1Supply & Installation of Wall mounted exhaust fan (9" dia.) of decorative plastic body
and blade with louvers on the outside of approved make15.00 Nos
6.2
Supply & Installation of approved make Ceiling Fan (4'dia / 1200 mm dia) (BEE 5 star
rated) (Colour :- White / Brown / Ivory as approved by client / architect / consultant)
alongwith required hardware & accessories, etc.
5.00 Nos
6.3
Supply & Installation of approved make 400 mm dia. Decorative Wall Fan along with
required hardware & accessories, etc. as approved by Architech / Consultant / Client. 12.00 Nos
6.4
Supply & Installation of approved make 400 mm dia. Decorative Pedastal Fan
alongwith required hardware & accessories, etc. as approved by Architech / Consultant
/ Client.
0.00 Nos
7 Lighting Controls / Sensors
7.1
Supply & Installation of Occupancy cum Presence Sensor suitable for 'ON/OFF'
control of LED / CFL / PL, etc. type light fixtures / fittings & shall be able to detect
micro moments along with required control wiring from sensor to ballast/switch board
as required including necessary hardware & accessories, etc. Detection range for
movement shall be 7 meter diameter with installation height of 2.5 meter
approximately. (Hager / Honeywell / Lutron / equivalent make & model in Schneider /
Wipro / Philips / CG / GE make or any other equivallent make as approved by client
/architect)
52.00 Nos
7.2
Supply & Installation of Occupancy cum Movement Sensor suitable for 'ON/OFF'
control of LED / CFL / PL, etc. type light fixtures / fittings along with required control
wiring from sensor to ballast/switch board as required including necessary hardware &
accessories, etc. Detection range for movement shall be 6m diameter with installation
height of 2.5 meter approximately. (Hager / Honeywell / Lutron / equivalent make &
model in Schneider / Wipro / Philips / CG / GE make)
45.00 Nos
TOTAL of SECTION (E) RS.
ELECTRICAL BOQ Page 60 of 80
M/s. Shetgiri Associates
S.NO PARTICULARS QTY UNIT RATE (Rs.) AMOUNT (Rs.)
F MISCLLANEOUS WORK
1
Lumpsum charges for arranging temporary power supply and lighting for all the
contractor at site including the required number of tubelight fittings, suffficient number
of plug points with plug tops, providing temeporary supply arrangements for temeparay
workstations and including all the necessary safety devices like ELCB etc. to ensure
SAFE & CONTINUED supply at site. Also removing of all type of existing electrical
installations including light fittings, conduits, switch, socket, casing-capping, DB's
MCB's, etc. complete as directed by the client / consultant at site & handing over to the
client / Engineer Incharge at site. (Item to be quoted as one JOB on lumpsum
basis.)
1.00 LS
2
Supplying & shock treatment / restoration charts written in Hindi, English & Marathi
(Local Language) duly framed and covered with 2.8mm glass as required as per the
locations as approved by Client / Architect / Consultant at site.
5.00 Nos
3
Supply and erection Standard First Aid Box complete as per specifications as per
location as approved by the Client / Architect / Consultant with necessary antiseptic
cream, medicine for use on wounds due burn, crepe bandage, guage bandage,
medicated ready to use bandage (Band aid) adhesive tape for medicinal use, scissors,
antiseptic solution (Savlon or similar) etc. (All above contents shall be of standard
makes & shall be checked, confirmed & approved the Client / Consultant for Expiry
Dates of all the Products provided in First Aid Box at the time of installtion at site.)
5.00 Nos
4 Shifting of Existing UPS
Uninstallment of exsting 10 KVA UPS with batteries, stand & allied accessories
and reinstall at new place with batteries,stand & allied accessories,replace the
old detoriated lugs & wires of batteris if require.
5.00 Jobs
TOTAL of SECTION (F) RS.
II DATA / VOICE NETWORKING
A DATA NETWORKING
1
Supply, Installation, Termination, Testing, Commissioning & Certification of Data point
including approved make Cat - 6 UTP cable through already laid underfloor trenches /
raceways / conduits & including MS conduit in case of concealed in wall / on surface for
above false ceiling, RJ45 information outlet, single / dual / quad type face plate, PVC
back box etc. including Termination, Testing and Documentation of UTP Points
complete as required.
450.00 Nos.
2Supply & installation of CISCO catalyst 2960s / equivalent approved make 24 port24
Port 1 GBPS manageable switch for LAN connectivity.19.00 Nos.
3 Supply & installation of 48 port jack panel 4.00 Nos.
4
Supply, Installation, testing & commissioning of 32U Wall mounted Network rack with
all necessary accesories of size (600 X 800)mm with 2 cable tray and PDU alongwith
all necessary hardware & accessories as required.
4.00 Nos.
5 Supply of mounting cord (7 feet') 450.00 Nos.
6 Supply of mounting cord (3 feet') 450.00 Nos.
TOTAL of SECTION - (II-A) RS.
ELECTRICAL BOQ Page 61 of 80
M/s. Shetgiri Associates
S.NO PARTICULARS QTY UNIT RATE (Rs.) AMOUNT (Rs.)
B VOICE NETWORKING
1
Supply, Installation, Termination, Testing, Commissioning & Certification of RJ-11
telephone socket outlet point alongwith PVC back box including 2-Pair wire as
telephone cable from Telephone MDF upto individual Telephone socket outlet through
already laid underfloor trenches / raceways / conduits & including MS conduit in case of
concealed in wall / on surface for above false ceiling including all necessary hardware
& accessories, etc. complete as required.
450.00 Nos.
2
Supply, installation, testing and commissioning of indoor type telephone Main
Distribution Frame (MDF) / Box with suitable S.S. frame for mounting tag module,
cable, wires and incorporated in 16 SWG MS box with proper lockable cover. The box
should be fixed on wall with suitable fasteners including painting & earthing. This also
includes fixing the cable, distribution chart sufficient space for the cables, wires etc.to
be provided in the box for :-
2.1Supply & Installation of 200 pair MDF with Krone module including all hardware &
accessoried , etc. complete as required.4.00 Nos.
3
Supply & Laying of 50 pair telephone cable on cable tray / duct / route as instructed &
approved at site including all necessary hardware & accessories, etc. 116.00 Rmt
TOTAL of SECTION - (II-B) RS.
Please Note : The rates quoted hereinabove shall be Exclusive of GST and GST
shall be additional at actuals.
SEAL AND SIGN OF BIDDER
ELECTRICAL BOQ Page 62 of 80
M/S. SHETGIRI AND ASSOCIATES
S.No Description Qty. Unit Rate (Rs.) Amount (Rs.)
SCHEDULE: - GREEN BUILDING SYSTEMS (RAIN WATER HARVESTING
SYSTEM) WORKS & EXTERNAL / OUTDOOR BEAUTIFICATION WORKS
I RAIN WATER HARVESTING SYSTEM WORKS: -
1 Boring / drilling bore well of required dia for casing/ strainer pipe, by suitable method
prescribed in IS: 2800 (part I), including collecting samples from different strata,
preparing and submitting strata chart/ bore log, including hire & running charges of
all equipments, tools, plants & machineries required for the job, all complete as per
direction of Engineer -in-charge, upto 90 metre depth below ground level.
R.Mt 180.00
a All types of soil
i 350 mm dia
2 Supplying, assembling, lowering and fixing in vertical position in bore well,
unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS:
12818, including required hire and labour charges, fittings & accessories etc. all
complete, for all depths, as per direction of Engineer -in-charge.
R.Mt 110.00
150mm nominal size dia
3 Supplying, assembling, lowering and fixing in vertical position in bore well,
unplasticized PVC medium well screen (RMS) pipe of required dia, conforming to
IS: 12818, including required hire and labour charges, fittings & accessories etc. all
complete, for all depths, as per direction of Engineer -in-charge. There shall be an
ring along the peripherals of the building structure.
R.Mt 180.00
150mm nominal size dia
4 Supplying & Installing in position Rain water in-built PVC pipe filters. The Pipe to be
divided into three compartments by wire mesh with each component to be filled with
gravel and sand alternatively. A layer of charcoal to be inserted between two layers
etc complete. The system to be designed as an consolidated unit for RWH. The
system to be of Jalsantosh or equivalent approved make etc complete.
R.Mt 105.00
5 Supplying and errecting centrifugal water pumps (Monoblock), 415 V, 3 phase, 50
cycles AC supply of 5 HP with discharge of 5.8/8.5 litres per second for head of
20/36 metres and 65 mm suction / 50 mm delivery pipe on provided cement
concrete foundation as per manufacturers specifications. (1 Set = 1 + 1 standby)
Set 1.00
6 Supplying and errecting automatic control panel for 1 to 6 HP centrifugal pump set
consisting of DOL starter Single phasing preventer, water level controller, ammetter,
voltmeter, phase indicating lamp etc. 4 way for U/G tank and OH tank. The quoted
rate shall be all inclusive of the assessories, flat flexible 3 core copper cabling,
fittings, fixtures required for sucessful commissioning of the pump sets as per the
manufacturers specifications.
Each 3.00
TOTAL OF RAIN WATER HARVESTING SYSTEM WORKS Rs.
I EXTERNAL / OUTDOOR BEAUTIFICATION WORKS: -
1 Supply, Providing, Fixing & Installation of semi unitised structural glazing system to
support / withhold 6 mm thick reflective toughned glass of approved make such as
Saint Gobain, Glaverbell or equivalent approved to be fixed having main frame work
of mullions and transomes of designed extruded aluminium sections to withstand a
wind pressure of the local area as per IS standards and fabricated fixed at all levels,
elevation & heights. The extruded aluminium section shall be finished, with
electrolytic Colour anodised of approved colour matching the existing color as duly
provided of minimum 20 microns. Extruded section shall be of 6063T6 Alloy or
BSH9 confirming to IS-63400. Rate shall include fixing of the main frames to
Substructure provided new with necessary clamps, Fastening straps, nuts, bolts,
rivets, washers and other fastening materials shall be in stainless steel. Rate shall
include EPDM/ Neoprene tripple sealant barrier, approved silicon of recommended
grade from DOW corning/ equivalent etc. complete for full proof & seep-proof
system.
Sq. Mts 22.00
8. INTERIOR RENOVATION WORK OF NABARD REGIONAL OFFICE AT 54, WELLESLEY ROAD,
P.B.NO. 5, SHIVAJI NAGAR, PUNE-411005
GREEN BUILDING SYSTEM BOQ
M/S. SHETGIRI AND ASSOCIATES
2 Supply and Installation of Fire rated Door of minimum 45mm thickness of Godrej or
equivalent approved as per standard manufacturers specifications & complying with
the relevant sections of B.I.S codes and National Building codes of India.
Nos 2.00
FD - Size = 1500 x 2100mm (Equal / Unequal Double leaves) Fire rated steel door
(Minimum of Two hours fire rating) with fire rated square vision panel of size 380
mm X 380 mm including SS ball bearing butt hinges, mortice sash lock, SS lever
handle with internal thumb turning arrangement, heavy duty type and external key
operation including heavy duty floor spring and panic bar for opening the door of
Dorma, Kich, Haffelle or equivalent make etc complete
3 PROVIDING POLYCARBONATE SHEETS FOR SIT-OUT SPACES WITHIN THE
LANDSCAPE BELTS
Supply, erection, fixing & Installation of coloured Multi-cell heavy duty
Polycarbonate Sheets with U.V coating of Lexan or equivalent approved make,
16mm thk of approved colour & design for sit-out spaces & roofs including
necessary fixing arrangements, assessories, hardware, bolts etc complete as per
manufactures specifications & installation standards as per the technical
specifications.
The rate shall include fixing the sheets to the Standing Seam Connecting System
as per technical specifications & manufacturers standards, which shall be free
floating in MS Hollow Sectional frame work. The rate shall include supply & fixing of
polycarbonate roofing sheets including the cost towards Supply, fabrication,
erection & installation of new M.S / structural steel hollow sections & supporting
elements, assessories etc complete
Sq. Mts 8.00
4 Suply and installation of 8-way, TPN, Double Door, Outdoor Lighting Distribution
Board (LDB), flush mounted on wall, interconnected wiring complete with earthing
lugs housing following switchgears:
(Similar to MDS / equivalent from tender List of approved make)
1 no., 63A, 300 mA, RCBO as incomer
12 nos, 16/25A, SP, MCB outgoing
Full Set as above Nos 1.00
5 Supply, Installation Testing & Commissioning of Fantasy Bollard Light fitting -
Decorative Die cast aluminium Bollard with UV stabilized polycarbonate diffuser,
suitable for 18w LED lamps complete with driver & required neccessary hardware &
accesories. The rate shall also include required connection to the fitting with copper
cable.
Nos 2.00
6 Supply, Installation, Testing & Commisioning of 1x18w LED Lamp Solar Street
light fitting with 8ft. Height (from ground level) pole of standalone type with
battery back up of 8 to 10 hours alongwith all necessary hardware & accessories
etc. (MNRE approved make only)
Nos 10.00
TOTAL OF EXTERNAL / OUTDOOR BEAUTIFICATION WORKS Rs.
SUM TOTAL OF GREEN BUILDING SYSTEMS (RAIN WATER HARVESTING
SYSTEM) WORKS & EXTERNAL / OUTDOOR BEAUTIFICATION WORKS
Rs.
Please Note : The rates quoted hereinabove shall be Exclusive of GST and
GST shall be additional at actuals.
SEAL AND SIGN OF BIDDER
GREEN BUILDING SYSTEM BOQ
M/s. SHETGIRI ASSOCIATES
Sl.
No.
Description Quantity Unit Rate(Rs.) Amount (Rs.)
1 2 3 4 5 6
1.00 Supply, Installation, Testing and Commissioning of
Intelligent Addressable fire alarm control panel with 1
loop card and battery backup of 24 hrs in normal
condition and 30 min in alarm condition with
necessary accessories, BMS integration module and
as per technical specification.
1 Nos
2.00 Multisensor Detector with accessories as per
technical specification
62 Nos
3.00 Response Indicator with accessories as per technical
specification
16 Nos
4.00 Fault Isolators module with accessories as per
technical specification
5 Nos
5.00 Addressable Control relay modules. (for GRP, ACS,
Hooters, PAS) as per technical specification
25 Nos
6.00 Addressable Manual Call Points with accessories as
per technical specification
9 Nos
7.00 Addressable monitor modules with accessories as
per technical specification (monitoring VESDA)
2 Nos
8.00 Sounders with strobes with accessories as per
technical specification
10 Nos
9.00 2 core x 1.5 Sqmm FRLS armoured copper cable as
per technical specification (As per requirement)
1 Lot
10.00 25mm flexible MS conduit with accessories 100 Mtrs
11.00 Ceasefire 4 Kg Fire Extinguisher Clean Agent ,
Stored Pressure Type, Pressure Gauge, Gross
Weight 6.9 Kg, empty Weight 2.9 Kg, Can Height
435MM, Diameter 140 MM, Discharge minimum 9
Secs, Controllable discharge mechanism, Range
minimum 4 Meters, applicable on Class A,B,C and
electrically started Fire, A Rating 5A, B Rating 34B,
Can Construction : Deep drawn & CO2, Mig welded,
Valve Construction : Forging & Machining, Internal
Coating of Can : Epoxy Powder coating, External
Coating of Can : Epoxy Polyster Powder coating,
Sheet metal thickness :1.60 MM, Helium Leak
Detection Tested, 5 Years Warranty
17 Nos
12.00 PUBLIC ADDRESS SYSTEM
Supply, Installation, Testing and Commissioning of
PUBLIC ADDRESS SYSTEM with 6 Zone Micro-
Processor Based based selection panel complete
with interface fire for fire tone generator and Paging
Announcement System & Gooseneck Microphone
with rack to mount all controllers.
1 Nos
13.00 6W Ceiling Mount Speaker 8 Nos
14.00 6 W Wall Mounted Speaker 22 Nos
15.00 Volume Control (for DC Manager Cabins) 2 Nos
16.00 2 core x 1.5 Sqmm FRLS armoured copper cable 650 Mtrs
9. PROPOSED LV SYSTEM WORKS OF NABARD REGIONAL OFFICE AT 54, WELLESLEY ROAD, P.B.NO. 5,
SHIVAJI NAGAR, PUNE-411005
IBMS Supply & Installation
LV SYSTEM BOQ Page 65 of 80
M/s. SHETGIRI ASSOCIATES
17.00 ACCESS CONTROL SYSTEM
Supply, Installation,Testing and Commissioning of
Access Control System TCP/IP enabled 2 Reader
Access Door Controller with Power supply and
housing
12 Nos
18.00 Finger print biometric reader with smart card reader
with accessories
2 Nos
19.00 Smart Card reader with accessories 23 Nos
20.00 Smart Cards 200 Nos
21.00 Double leaf 600 lbs electromagnetic lock with inbuilt
magnetic contact & Power Supply with accessories
1 Nos
22.00 Single leaf 600 lbs electromagnetic lock with inbuilt
magnetic contact & Power Supply with accessories
12 Nos
23.00 Emergency break glass unit with accessories 13 Nos
24.00 Access Management Software with Time &
Attendance Software
1 Lot
25.00 PC for Access Control Software 1 Nos
26.00 Card Printer with accessories 1 Nos
27.00 8 core x 0.75 sq.mm. armoured cable with
accessories
1200 Mtrs
28.00 4 core x 0.75 sq.mm. armoured cable with
accessories
1300 Mtrs
29.00 2 core x 1 sq.mm. armoured cable with accessories 1200 Mtrs
30.00 CCTV SURVEILLANCE SYSTEM
UL Listed 1/3" CMOS, 800x 600 Resolution, 3~8mm
Varifocal lens, minimum of 0.5 lux @ 40 IRE, POE
enabled indoor Dome Camera with accessories &
as per technical specification
28 Nos
31.00 UL Listed 1/3" CMOS, 1080x 720 Resolution,
3~8mm Varifocal lens, minimum of 0.5 lux @ 40 IRE,
PTZ Camera with accessories & as per technical
specification
1 Nos
32.00 Network Video Recorder with backup of 30 days
(Recording: 4 CIF Resolution, 15fps, 30days online )
with camera license & 2 No's. of client licenses
1 Lot
33.00 PC for Monitoring camera as per technical
specification
1 Nos
34.00 42" Colour LED monitor as per technical
specification
2 Nos
35.00 Aspiration based Detection System
Supply, Installation, testing and commissioing of
Aspiration Detection Panel for Server Room as per
technical specification
1 Lot
36.00 Power Supply Unit with accessories as per technical
specification
1 Nos
37.00 Capillary tubes as per with accessories as per
technical specification
11 Nos
38.00 Electronic Hooter 1 Nos
39.00 ISI approved 25mm CPVC Conduit with accessories
as per technical specification
150 Mtrs
40.00 Fire Suppression System
Supply, Installation,Testing and Commissioning
of 120 Ltr seamless cylinder with valve as per
technical specification
8 Nos
41.00 Novec 1230 Agent as per technical specification 680 Kgs.
LV SYSTEM BOQ Page 66 of 80
M/s. SHETGIRI ASSOCIATES
42.00 Master Cylinder Kit with following items as per
technical specification:
- Pr. Guage + Low Pr. Supervisory Switch
- Electromagnetic Actuator
- Manual Actuator
- Pneumatic Actuator
- Flexible Discharge Hose
- Flexible Actuation Hose
5 Nos
43.00 End Slave Cylinder Accessories as per technical
specification
Pressure Operated Control Head
Actuation Hose, 30"
Discharge Hose, 2" x 31"
3 Nos
44.00 El Check 2" (Manifold Check Valve) 4 Nos
45.00 Gas Discharge Nozzles 18 Nos
46.00 Seamless Piping with manifold as per technical
specification
1 Lot
47.00 Gas Release Panel as per technical specification 5 Nos
48.00 Abort Switch 5 Nos
49.00 Release Switch 5 Nos
50.00 Hooter with Power Supply 5 Nos
51.00 2 core x 1.5 Sqmm FRLS armoured copper cable as
per technical specification
80 Mtrs
52.00 Rodent Repellent System
Supply, Installation,Testing and Commissioning of
Microprocessor based Ultrasonic Rodent Repellent
System with stands as per technical specification
4 Nos
53.00 Rodent Transducer as per technical specification 47 Nos
54.00 Rodent Wire (275 meters) as per technical
specification
4 Lot
55.00 2 core x 1.5 Sqmm FRLS armoured copper cable as
per technical specification
80 Mtrs
56.00 Water Leak Detection System
Supply, Installation,Testing and Commissioning of
Water Leak Detection Panel with Modbus
connectivity
1 Lot
57.00 Water Leak detection Cable Sensor – 10 mtrs 2 Nos
58.00 Water Leak detection Cable Sensor – 25 mtrs 2 Nos
59.00 Electronic Hooter 1 Nos
60.00 2 core x 1.5 Sqmm FRLS armoured copper cable as
per technical specification
50 Mtrs
LV SYSTEM BOQ Page 67 of 80
M/s. SHETGIRI ASSOCIATES
61.00 Workstation Operator Machine: Intel i3 processor 3rd
generation, 500GB HDD, , 4GB RAM, 52X CD RW
,21" colour monitor, USB Mouse, 2 serial, 1 parallel
port & Windows operating system
1 Nos
62.00 Building Management System Software 1 Nos
63.00 Colour Laser Printer 1 Nos
64.00 32 Bit DDC Controller above along with System
Integration Units, Powder Coated cabinets as per IS
Standards for Electrical Panels and all internal
terminations and cabling to monitor temperature &
humidity in server room
DDC for intergartion of variours physical security
substems mentioned and Temperature and humidity
monitoring as per IO summary
PAC Units Integration (30 Points / Unit)
UPS Units Integration (30 Points / Unit)
Fire Alarm System
Water Leak Detection System
1 Lot
65.00 Temperature & Humidity Sensor 30 Nos
66.00 2 core 1.0 sq.mm PVC Insulated Cu Armoured Cable 750 Mtrs
67.00 TV Screens for Manager Cabins Supply and
Installation with wall mounted 32" LED TV screen for
DC manager Cabin-01 and -02 (DTH/Cable
Connection shall be provided by RISL.)
2 Nos
68.00 Monitor Screens for Manager Cabin-03: Supply and
Installation of Wall mounted 42" LED Monitor screen
for DC manager Cabin-03 with required length of
VGA/HDMI Cable
1 Nos
Rs.
SEAL AND SIGN OF BIDDER
TOTAL OF LV SYSTEM WORKS
Please Note : The rates quoted hereinabove shall be Exclusive of GST and
GST shall be additional at actuals.
LV SYSTEM BOQ Page 68 of 80
M/s. SHETGIRI and ASSOCIATES
Sr. No. Description Unit Qty Rate Amount
A AUDIO SYSTEM
14" Full-range ceiling speaker, 70/100V transformer with 8 Ω
bypass, 140° conical coverage,
includes C-ring and rails for blind mount installation.
EA 8
26.5" Two-way surface speaker, 70/100V transformer with 8 Ω
bypass, 130° conical coverage,
includes Yoke Mount. Color - White.
EA 2
3
1/2 RU 4 Channel ENERGY STAR amplifier / Multichannel
operation 60 watts into 8 Ω & 4 Ω,
Bridged pair operation 200 watts into 8Ω & 4Ω, and 250 watts
into 70v and 100v / 100-240
VAC Operation
EA 1
42 channels, 300 watts/ch at 8Ω, 425 watts/ch at 4Ω, Dual
Channel amplifierEA 1
5
8 Mic/ line inputs with AEC, 8 line outputs, 8 Nos configurable
ports to Inputs & outputs, Configurable ports should be able to
configured for Input or Outouts, 16 GPIO ports, 1 PSTN (Analog
Telephone connectivity), 1 LAN (VOIP)
EA 2
6
Boundary Microphone (half-cardioid) with 3-pin XLR connector,
black, Half-cardioid polar pattern • Flat, wide range frequency
response • High-quality reproduction of speech
• Unobtrusive design • Ceiling or tabletop mounting • Fast and
easy installation
EA 23
7 RGB LED Ring for Classis BM 3x series EA 23
8UHF series, Wireless handheld microphone, with True Diversity
Microphone sets Receiver, Cardiod microphone Transmitter
(handheld), & Antennas
EA 4
9 XLR Connectors, for Microphones EA 23
10 Buttons for Push-to-talk or Look at me function EA 41
B VIDEO SYSTEM
1
Optical Screen Laser Panel, 100" Diagonal optical Screen, For
Top-mounted Ultra-short throw projector with f:0.15-0.35:1 lens
throw range. {optical screen can be used In brightlights for Video
conferencing & presentation or Cinema application}
EA 1
2Ultra-short throw projector, 4000 ANSI Lumens, Full HD
(1920x1080), Laser light source projector, supplied with Ceiling
mount kit, 1 HDMI, 1 LAN connectivity
EA 1
3
55" Display:-Key Features:- Brightness: 350 cd/m2, Bezel :
Top/Left/Right 11.9 mm (Bottom 18.0 mm), Depth : 54
mm(38.6mm:Thinnest Part), Orientation : Landscape & Portrait
mode, Interface : HDMI, DVI, RGB, RJ45, IR, RS232C, USB,
Speacker : Built-in
EA 4
4
Wireless Presentation Solution:- Login using conventional Wi–Fi
and/or LAN connections
Supports Windows and Mac laptops, Chromebooks as well as
iOS, Windows and Android mobile operating systems
High–quality video streaming, supports full HD 1080p/60
(using the VIA app Multimedia feature) — supports up to 6Mbps
video bit rate when using the built–in Wi–Fi module in Access
Point mode
Up to two participant screens can be displayed simultaneously on
main screen
Audio — D
EA 1
C VIDEO CONFERENCE SYSTEM
1CISCO SX-80, Set of CODEC, Microphone, & Single Camera,
Complete system with Ethernet or RS232 control, 1080p Video
conference capability
EA 1
2 1 YR US ESS 8X5XNBD CTS-SX20-PHD12X-K9 EA 1
3 MultiSite Option for SX80 (1+3) EA 1
4 Auxillary Camera, EA 1
D SWITCHING SYSTEM
10. AV SYSTEM WORKS OF NABARD REGIONAL OFFICE AT 54, WELLESLEY ROAD, P.B.NO. 5, SHIVAJI
NAGAR, PUNE-411005
AV BOQ Page 69 of 80
M/s. SHETGIRI and ASSOCIATES
1Sliding Cover Type Cable Cubby with RJ45 x 2 / Audio jack x 1 /
HDMI x 1 / VGAx1 / DP X 1/ USBx1 / Universal power socket x 1
/ USB Charger X 1
EA 4
23 Inputs Source Extender Kit, 1VGA+A, HDMI, Display port
inputs, to Extended over HDBT with scaling Receiver with HDMI
output, Auto-switching between inputs, 4k Switching
EA 4
3
6x6 HDMI Source Matrix Switcher with 6 outs on HDBT,
Simultaneous 4 outputs on HDMI, 4K@60Hz 8bit 4:2:0 and 4K
HDR @24Hz 10bit with chroma sub-sampling rate of 4:2:0
supported to 70m/230ft
1080p@60Hz 48bit color supported to 100m/328ft, incuding 3D
Latest HDCP 2.2 encryption technology supported ensuring
compatibility with the latest 4K UHD content and sources,
EA 1
4HDBaseT™ 4K UHD Receiver (4K: 70m/230ft | 1080p:
100m/328ft), EA 5
5 DP Patch cable EA 4
6 HDMI patch Cable EA 4
7 VGA+A Cable EA 4
8 HDMI 6 ft Cable EA 15
9 HDMI 15 feet cable EA 2
E CONTROL SYSTEM
1
3-Series Control System®-(2) 5-pin 3.5 mm detachable terminal
blocks;
Bidirectional RS-232 ports [8]; IR-(8) 8-pin 3.5 mm detachable
terminal block; RELAY OUTPUT 1 – 8, LAN(1), CONTROL
SUBNET
EA 1
2
7” Touch Screen, Black Smooth:- Display Type TFT active matrix
color LCD, Size 7 inch (178 mm) diagonal, Aspect Ratio 17:10
WSVGA, Resolution 1024 x 600 pixels, Brightness 350 nits
(cd/m²), Contrast 1100:1, Color Depth 24-bit, 16.7M colors,
Illumination Edgelit LED w/auto-brightness control, Viewing
Angle ±80° horizontal, ±80° vertical, Touch Screen Projected
capacitive, 5-point multi-touch capable
EA 1
3 Wi-Fi access points, EA 0
4 8 port PoE n/w switch EA 1
5 I-pad for wireless control, ipad mini. EA 0.00
6WQ Make 18U x 600mm x 600mm floor mount with
casterwheels, FANs on top, Power strip, Power distrubtion units,
Front Glass door, Side doors & back doors
EA 1
7
4-zone Univarsal Lighting control system, Forward Phase
(leading edge) or Reverse Phase (trailing edge) Electronic Low
Voltage, Incandescent, Neon/Cold Cathode, Magnetic Low
Voltage, Dimmable 2 Wire Fluorescent, & Non-Dim Lighting
EA 0
88 Channel 0-10V Dimmer Module, 2 Feeds, LED, incandescent,
fluorescent, magnetic low-voltage, electronic low-voltage, high-
intensity discharge (HID)
EA 1
9 IR Probes EA 5
F CABLES1 Stereo Audio bulk cable Mtrs 50
2 MONO Audio bulk cable Mtrs 460
3 16 AWG Speakers cable Mtrs 150
4 Connectors, Heatshrinks, Cable ties etc. LS 1
523/24 AWG,un Shielded Twisted pair cable, Spool of 300 Mtrs,
Mtrs 200
5 8-port Relay strip, Low Voltage to Highvotage relay strip EA 1
G SERVICES
6 INSTALLATION, TESTING, COMMISSIONING - 1
7 PROGRAMMING OF THE COMPLETE SYSTEM - 1
8 PROJECT MANAGEMENT FOR ENTIRE PROJECT - 1
9DRAWINGS & DOCUMENTATION OF THE ENTIRE PROJECT
- 1
TOTAL EQUIPMENT & SERVICES COST
AV BOQ Page 70 of 80
M/s. SHETGIRI and ASSOCIATES
Please Note : The rates quoted hereinabove shall be Exclusive of
GST and GST shall be additional at actuals.
Note: - The above mentioned BOQ depicts the Quoted Make &
Model, which is a part of the Estimate considering the said make
/ model. However the contractor shall quote for any Make &
Model, which forms a part of the tender document & enlisted in
the "List of Approved / Suggested Make". The contracting agency
shall note that it is mandatory to mention the Make & Model
Number out of the list of approved / suggested make, for which
the line item-rate has been quoted, at the time of quoting for the
job assignment.
SEAL AND SIGN OF BIDDER
AV BOQ Page 71 of 80
M/S. SHETGIRI and ASSOCIATES
Sr.No Description Unit QtyRate
INR
Amount
INR
A AUDIO SYSTEM
1
4" Full-range ceiling speaker, 70/100V transformer with 8 Ω
bypass, 140° conical coverage, includes C-ring and rails for
blind mount installation.
nos 4
2Energy Star Amplifier, 60watts @ 8 ohms / 70v / 100v, Dual
Channel amplifiernos 1
3
8 Mic/ line inputs with AEC, 8 line outputs, 8 Nos
configurable ports to Inputs & outputs, Configurable ports
should be able to configured for Input or Outouts, 16 GPIO
ports, 1 PSTN (Analog Telephone connectivity), 1 LAN (VOIP)
Nos 1
4
Boundary Microphone (half-cardioid) with 3-pin XLR
connector, black, Half-cardioid polar pattern • Flat, wide range
frequency response • High-quality reproduction of speech
• Unobtrusive design • Ceiling or tabletop mounting • Fast and
easy installation
nos 9
5 RGB LED Ring for Classis BM 3x series nos 9
B VIDEO SYSTEM
1
86” Ultra HD Signage with Split-Screen Functionality:- Ultra
HD Resolution (3840x2160) High Efficiency Video Coding,
Multiple Screen with PBP or PIP,Mirroring, Brightness
500cd/m2, Input, HDMI, DP, DVI-D, RGB, Audio, USB 3.0, SD
card, External Control
RS232C In, IR Receiver, Pixel Sensor,
nos 1
2 Bracket nos 1
3 Bracket EA 1C VIDEO CONFERENCE SYSTEM
1
CISCO , Set of CODEC, Microphone, & Single Camera,
Complete system with Ethernet or RS232 control, 1080p Video
conference capability
NOS 1
2 1 YR US ESS 8X5XNBD CTS-SX20-PHD12X-K9 Nos 1
3 MultiSite Option for SX20 (1+3) Nos 1
AV BOQ Page 72 of 80
M/S. SHETGIRI and ASSOCIATES
D SWITCHING SYSTEM
1
Sliding Cover Type Cable Cubby with RJ45 x 2 / Audio jack x 1
/ HDMI x 1 / VGAx1 / USBx1 / Universal power socket x 1 /
USB Charger X 1
Nos 3
2
4-input (12 source) Multi-View Scaler with 2x 4K UHD
Outputs:- The WyreStorm SW-0402-MV-HDMI multi-view
scaler or 4x2 matrix enables seamless 4x2 matrix switching and
upscaling between analog and/or digital AV sources with dual
4K HDMI outputs.
nos 1
3 HDMI patch Cable - 15 Meter nos 3
4 VGA+A Cable - 15 Meter nos 3
5 HDMI 6 ft Cable nos 3
6 HDMI 15 feet cable nos 1
7Digital Audio To Ananlog Audio Converter active adapter
nos 1
E CONTROL SYSTEM
1
3-Series Control System®-(2) 5-pin 3.5 mm detachable
terminal blocks;
Bidirectional RS-232 ports [8]; IR-(8) 8-pin 3.5 mm detachable
terminal block; RELAY OUTPUT 1 – 8, LAN(1), CONTROL
SUBNET
Nos 1
2
7” Touch Screen, Black Smooth:- Display Type TFT active
matrix color LCD, Size 7 inch (178 mm) diagonal, Aspect Ratio
17:10 WSVGA, Resolution 1024 x 600 pixels, Brightness 350
nits (cd/m²), Contrast 1100:1, Color Depth 24-bit, 16.7M
colors, Illumination Edgelit LED w/auto-brightness control,
Viewing Angle ±80° horizontal, ±80° vertical, Touch Screen
Projected capacitive, 5-point multi-touch capable
Nos 1
3 Wi-Fi access points, nos 0
4 8 port PoE n/w switch nos 1
5 I-pad for wireless control, ipad mini. NOS 0
6 WQ Make 18U x 600mm x 600mm Wall Mount:- Nos 1
7
4-zone Univarsal Lighting control system, Forward Phase
(leading edge) or Reverse Phase (trailing edge) Electronic Low
Voltage, Incandescent, Neon/Cold Cathode, Magnetic Low
Voltage, Dimmable 2 Wire Fluorescent, & Non-Dim Lighting
EA 0
8
8 Channel 0-10V Dimmer Module, 2 Feeds, LED, incandescent,
fluorescent, magnetic low-voltage, electronic low-voltage, high-
intensity discharge (HID)
EA 1
F CABLES1 Stereo Audio bulk cable Mtrs 50
2 MONO Audio bulk cable Mtrs 90
3 16 AWG Speakers cable Mtrs 60
4 Connectors, Heatshrinks, Cable ties etc. Mtrs 1
523/24 AWG,un Shielded Twisted pair cable, Spool of 300 Mtrs,
Mtrs 0
6 4 port Relay strip for Rack power ON / Off Mtrs 1
AV BOQ Page 73 of 80
M/S. SHETGIRI and ASSOCIATES
G SERVICES6 INSTALLATION, TESTING, COMMISSIONING - 1
7 PROGRAMMING OF THE COMPLETE SYSTEM - 1
8 PROJECT MANAGEMENT FOR ENTIRE PROJECT - 1
9DRAWINGS & DOCUMENTATION OF THE ENTIRE
PROJECT- 1
Please Note : The rates quoted hereinabove shall be
Exclusive of GST and GST shall be additional at
actuals.
Note: - The above mentioned BOQ depicts the Quoted
Make & Model, which is a part of the Estimate
considering the said make / model. However the
contractor shall quote for any Make & Model, which
forms a part of the tender document & enlisted in the
"List of Approved / Suggested Make". The contracting
agency shall note that it is mandatory to mention the
Make & Model Number out of the list of approved /
suggested make, for which the line item-rate has been
quoted, at the time of quoting for the job assignment.
SEAL AND SIGN OF BIDDER
TOTAL EQUIPMENT & SERVICES COST
AV BOQ Page 74 of 80
M/S. SHETGIRI and ASSOCIATES
Sr.No Description Unit Qty Rate Amount
A VIDEO SYSTEM
1
65" Display:- Key Features:- Brightness : 400 cd/m2, Bezel :Top/Left/Right 11.9 mm (Bottom 18.0 mm), Depth :56.5(41.1mm:Thinnest Part), Orientation : Landscape & Portraitmode, Interface : HDMI, DVI, RGB, RJ45, IR, RS232C, USB, Speaker :Built-in
Nos 1
2
Wireless Presentation Solution:- Login using conventional Wi–Fi
and/or LAN connectionsSupports Windows and Mac laptops, Chromebooks as well as iOS,Windows and Android mobile operating systemsHigh–quality video streaming, supports full HD 1080p/60 (using theVIA app Multimedia feature) — supports up to 6Mbps video bit rate
when using the built–in Wi–Fi module in Access Point modeUp to two participant screens can be displayed simultaneously on
main screenAudio — D
EA 1
3 HDMI 6 ft Cable nos 21 INSTALLATION, TESTING, COMMISSIONING - 1
Please Note : The rates quoted hereinabove shall be
Exclusive of GST and GST shall be additional at actuals.
Note: - The above mentioned BOQ depicts the Quoted Make &Model, which is a part of the Estimate considering the said make
/ model. However the contractor shall quote for any Make &Model, which forms a part of the tender document & enlisted inthe "List of Approved / Suggested Make". The contracting
agency shall note that it is mandatory to mention the Make &
Model Number out of the list of approved / suggested make, forwhich the line item-rate has been quoted, at the time of quotingfor the job assignment.
SEAL AND SIGN OF BIDDER
TOTAL EQUIPMENT & SERVICES COST
AV BOQ Page 75 of 80
M/S. SHETGIRI and ASSOCIATES
Sr.No Description Unit Qty Rate Amount
A VIDEO SYSTEM
1
55" Display:-Key Features:- Brightness: 350 cd/m2, Bezel :
Top/Left/Right 11.9 mm (Bottom 18.0 mm), Depth : 54
mm(38.6mm:Thinnest Part), Orientation : Landscape & Portrait
mode, Interface : HDMI, DVI, RGB, RJ45, IR, RS232C, USB,
Speacker : Built-in
Nos 1
2 HDMI 6 ft Cable nos 1
3 INSTALLATION, TESTING, COMMISSIONING nos 1
Please Note : The rates quoted hereinabove shall be
Exclusive of GST and GST shall be additional at actuals.
Note: - The above mentioned BOQ depicts the Quoted
Make & Model, which is a part of the Estimate
considering the said make / model. However the
contractor shall quote for any Make & Model, which
forms a part of the tender document & enlisted in the
"List of Approved / Suggested Make". The contracting
agency shall note that it is mandatory to mention the
Make & Model Number out of the list of approved /
suggested make, for which the line item-rate has been
quoted, at the time of quoting for the job assignment.
SEAL AND SIGN OF BIDDER
TOTAL EQUIPMENT & SERVICES COST
AV BOQ Page 76 of 80
Sr.No Description Unit Qty Rate Amount
A AUDIO SYSTEM
1
4" Full-range ceiling speaker, 70/100V transformer with 8
Ω bypass, 140° conical coverage,
includes C-ring and rails for blind mount installation.
nos 2
2 Amplifier, 35watts @ 8 ohms, Dual Channel amplifier nos 1
B VIDEO SYSTEM
194" Diagonal, Motorised Projection screen, 16:10 aspect
ratio, Matt white surfacenos 1
2 Ceiling Mount bracket for Projector nos 1
33300 ANSI Lumens, WXGA 1280x800 Resolution
projector, Ceiling moutable, HDMI Input, nos 1
4
Wireless Presentation Solution:- Login using
conventional Wi–Fi and/or LAN connections
Supports Windows and Mac laptops, Chromebooks as well
as iOS, Windows and Android mobile operating systems
High–quality video streaming, supports full HD 1080p/60
(using the VIA app Multimedia feature) — supports up to
6Mbps video bit rate when using the built–in Wi–Fi
module in Access Point mode
Up to two participant screens can be displayed
simultaneously on main screen
Audio — D
EA 0
D SWITCHING SYSTEM
1
Sliding Cover Type Cable Cubby with RJ45 x 2 / Audio jack
x 1 / HDMI x 1 / VGAx1 / USBx1 / Universal power socket x
1 / USB Charger X 1
Nos 1
2
3 Inputs Source Extender Kit, 1VGA+A, HDMI, Display port
inputs, to Extended over HDBT with scaling Receiver with
HDMI output, Auto-switching between inputs, 4k
Switching
EA 1
3 HDMI patch Cable - 3 Meter nos 1
4 VGA+A Cable - 3 Meter nos 1
5 HDMI 6 ft Cable nos 1
6 DP 3 Meter cable nos 1
F CABLES
1 Stereo Audio bulk cable Mtrs 10
2 MONO Audio bulk cable Mtrs 0
3 16 AWG Speakers cable Mtrs 20
4 High Power relay up/down EA 1
523/24 AWG,un Shielded Twisted pair cable, Spool of 300
Mtrs, Mtrs 30
G SERVICES
6 INSTALLATION, TESTING, COMMISSIONING - 1
7 PROGRAMMING OF THE COMPLETE SYSTEM - 1
8PROJECT MANAGEMENT FOR ENTIRE PROJECT
- 1
9DRAWINGS & DOCUMENTATION OF THE ENTIRE
PROJECT- 1
0.00
Please Note : The rates quoted hereinabove shall be
Exclusive of GST and GST shall be additional at
actuals.
Note: - The above mentioned BOQ depicts the
Quoted Make & Model, which is a part of the
Estimate considering the said make / model.
However the contractor shall quote for any Make &
Model, which forms a part of the tender document
& enlisted in the "List of Approved / Suggested
Make". The contracting agency shall note that it is
mandatory to mention the Make & Model Number
out of the list of approved / suggested make, for
which the line item-rate has been quoted, at the
time of quoting for the job assignment.
SEAL AND SIGN OF BIDDER
TOTAL EQUIPMENT & SERVICES COST
M/S. SHETGIRI and ASSOCIATES
Sr.No Description Unit Qty Rate Amount
A VIDEO SYSTEM
1
55" Display:-Key Features:- Brightness: 350 cd/m2, Bezel :
Top/Left/Right 11.9 mm (Bottom 18.0 mm), Depth : 54
mm(38.6mm:Thinnest Part), Orientation : Landscape &
Portrait mode, Interface : HDMI, DVI, RGB, RJ45, IR,
RS232C, USB, Speacker : Built-in
Nos 1
2 HDMI 6 ft Cable nos 1B SERVICES1 INSTALLATION, TESTING, COMMISSIONING - 1
Please Note : The rates quoted hereinabove shall be
Exclusive of GST and GST shall be additional at
actuals.
Note: - The above mentioned BOQ depicts the Quoted
Make & Model, which is a part of the Estimate
considering the said make / model. However the
contractor shall quote for any Make & Model, which
forms a part of the tender document & enlisted in the
"List of Approved / Suggested Make". The
contracting agency shall note that it is mandatory to
mention the Make & Model Number out of the list of
approved / suggested make, for which the line item-
rate has been quoted, at the time of quoting for the
job assignment.
SEAL AND SIGN OF BIDDER
TOTAL EQUIPMENT & SERVICES COST
AV BOQ Page 78 of 80
M/S. SHETGIRI and ASSOCIATES
Sr.No Description Unit Qty Rate Amount
A AUDIO SYSTEM
14" Full-range ceiling speaker, 70/100V transformer with 8
Ω bypass, 140° conical coverage, includes C-ring and rails
for blind mount installation.
nos 0
2 Amplifier, 35watts @ 8 ohms, Dual Channel amplifier nos 0
B VIDEO SYSTEM
1
55" Display:-Key Features:- Brightness: 350 cd/m2, Bezel :
Top/Left/Right 11.9 mm (Bottom 18.0 mm), Depth : 54
mm(38.6mm:Thinnest Part), Orientation : Landscape &
Portrait mode, Interface : HDMI, DVI, RGB, RJ45, IR,
RS232C, USB, Speacker : Built-in
Nos 1
D SWITCHING SYSTEM
1Sliding Cover Type Cable Cubby with RJ45 x 2 / Audio
jack x 1 / HDMI x 1 / VGAx1 / USBx1 / Universal power
socket x 1 / USB Charger X 1
Nos 1
2 HDMI patch Cable - 15 Meter nos 1
3 VGA+A Cable - 15 Meter nos 1
4 HDMI 6 ft Cable nos 0
5 HDMI 15 feet cable nos 1
F CABLES1 Stereo Audio bulk cable Mtrs 0
2 MONO Audio bulk cable Mtrs 0
3 16 AWG Speakers cable Mtrs 0
4 High Power relay up/down EA 0
523/24 AWG,un Shielded Twisted pair cable, Spool of 300
Mtrs, Mtrs 0
G SERVICES
6 INSTALLATION, TESTING, COMMISSIONING - 1
7 PROGRAMMING OF THE COMPLETE SYSTEM - 1
8PROJECT MANAGEMENT FOR ENTIRE PROJECT
- 1
9DRAWINGS & DOCUMENTATION OF THE ENTIRE
PROJECT- 1
Please Note : The rates quoted hereinabove shall
be Exclusive of GST and GST shall be additional at
actuals.
Note: - The above mentioned BOQ depicts the
Quoted Make & Model, which is a part of the
Estimate considering the said make / model.
However the contractor shall quote for any Make
& Model, which forms a part of the tender
document & enlisted in the "List of Approved /
Suggested Make". The contracting agency shall
note that it is mandatory to mention the Make &
Model Number out of the list of approved /
suggested make, for which the line item-rate has
been quoted, at the time of quoting for the job
assignment.
SEAL AND SIGN OF BIDDER
TOTAL EQUIPMENT & SERVICES COST
AV BOQ Page 79 of 80
M/S. SHETGIRI and ASSOCIATES
Payment
GST
Delivery
Insta. &
commi.
Storage
Space
Insurance
Policy
Ordering
Warranty
Validity
Out of scope
SEAL AND SIGN OF BIDDER
Usually for AV works considered to be Within 3-4 Weeks after material delivery.
General AV related Terms & Conditions:
Additional / Extra As applicable based on prevailing guidelines, percentage on components & worksUsually for AV works considered to be Within 5-6 Weeks
Storage space for materials with lock, Key & Security to be arranged by Client at Site.
Insurance policy for materials against theft or loss at site to be taken by Client.
Not Finalised.
The warranty for AV components is applicable for 12 months from the date of installation or 13 months from the date of delivery whichever is earlier. It shall be the responsibility
of the AV contractor to undertake to replace or repair any defective part that needs replacement or repairs by any reason or defective workmanship or defects during the warranty
period. The equipment should always be used through a stabilized power supply to be provided usually by Clients. Any damage to the system on account of power fluctuations or
spikes are usually not covered under warranty. Also the liable ceases in case of any damage to the equipment resulting out of Accidents, misuse, neglection, alterations,
modifications or substitution of any component of the equipment.
Any loss or damage resulting from fire, flood, exposure to weather conditions and any other force majeure.
15 days from the date of offer
Civil works (if any) like cutting of false ceiling, chipping etc, Cabling of Audio Cables or electrical work like conduits, raceways, powersupply etc and carpentry work
like any cutting on furniture has to be done by the agencies employed by the customer and will be executed
Page 80 of 80