instrucciones doubledecker m1 · bed tm h10 attach bunk bed slat cleat (6) to bunk bed...
TRANSCRIPT
www.hiddenbed.com
HiddenbedTM
ASSEMBLY INSTRUCTIONSMODEL DOUBLE DECKER
Hid
de
nb
ed
TM
CONGRATULATIONS!
YOU ARE A PROUD OWNER OFHIDDENBED
The ultimate furniture that Doubles your Space
Please read carefully the Assembly Instructions.
Should you have any questions
please contact our authorized dealer:
For further information please check
www.hiddenbed.com
Hid
de
nb
ed
TM
Follow these simple stepsto assemble your Hiddenbed
Put them together
Put the mattress in its place.
Assemble the 3 main parts
1 2
3
LOOK, YOUR HIDDENBED IS READY!
COMPONENTS
COMPONENTS
1+1
1
1
1
2
1
1a+1b
2a+2b
COMPONENTS1+1
1
Hid
de
nb
ed
TM
Front Bunk Bed Side
Bunk Bed Slats Cleat
Guardrail Front
1+1
18
1
Body Back
Shelf
Shelf Stretcher9
18
19
20
21
Part N° Name Qty.
MAIN PARTS &CARPENTRY LIST
BODY PARTS
BED PARTS
DESK PARTS
30
3
3
1
2
5 7
6
10
11
14
9
8
10
1112
13
14
15
1617
18
19
20
21
Make sure that:
Side panels bears on the floor at the same level. A carpet can be placedbeneath both said adjacent bearing sides, but not place carpet or anyshim beneath on side desk or body side alone.
Stand at the middle of the furniture to make the transformation.
Use a mattress of ............. of a maximum height of 10 inches.
Total weight added on the moving parts, best around 40 lb.
Avoid excessive or too asymmetric loads on desk.
While lowering, please verify that bed bottom does not touch things lefton the desk. Things left on the desk cannot exceed 18 inches height. Nextto the rear of the desk there is less height available.
As with a door or a rocking chair, take good care not to trap fingersbetween closing parts.
If power or signal cables are to be installed, consult a qualified person.
If the bed does not stay down by it, add more weight on the desk.if the situation continues have the position point of action changed to alower strength position.
Remember a force equivalent to lift a CRT monitor is needed to transformthe bed into desk.
Ask your retailer for more details.
TO OBTAIN A SAFE A RELIABLE PERFORMANCE
(!)Like a sliding door or a car door or a bike, you have todo certain things to enjoy Hiddenbed Safely andreliably. Pay attention to theses recommendations!
WARNINGS
Hid
de
nb
ed
TM
A1 A2 A3 A4 A5 A6
A7 A8 A9 A10 A11
MECH ARMPLATE2 Pcs
GAS SPRING2 Pcs
LOWERSUPPORT
2 Pcs
LOWERSUPPORT
PIN2 Pcs
COTTERPIN
2 PcsBEARER
2 Pcs
LINK PIVOT2 Sets
TRUNNIONBUSHING &
SCREW2 Sets
LOCK2 Pcs
BRAND PLATEor STICKER
1 Pcs
MECHANISM KIT BOX A
HARDWARE KIT
Confirmat, H2, 7x70
Confirmat, H12, 7x50
Screw, Ph head,H10, 4.5x45
Screw, Ph head, H14, 4.5x35
Screw, Ph head, H20, 4.5x30
Screw, Ph head, H9, 4.5x20
Screw, Ph head, H13, 3.5x40
Screw, Ph head, H4, 3.5x16
Flat Head Allen & bushing, H6, 6x60
Dowell, 10x30
Bolt & nut, H3,1/4 x 1 1/4
Wood plug, WP
PIN BALL2 Pcs
EXTRA TOOLS (not supplied)
T1 T2 T3
M4 L - KEY1 Pc
M5 L - KEY1 Pc
M10 L - KEY1 Pc
Extra tools needed:
Phillips Head Screwdriver to putscrew (H10, H14, H20, H9, H13, H4)and bend cotter pins.
Antiwear lubricant.
Hid
de
nb
ed
TM
A1
H3
H3
BODY ASSEMBLY
3 Attach plate (A1) to body side (1).Make sure the hook on the arms isfacing upwards.
H3
4 Attach lower support (A3) to body (1)but do not over tighten.
A2
1
A3
4
3H
idd
en
be
dT
M
Attach the Gas Spring end to pin ball (A11).1
2 Attach the Gas Spring (A2) to lower suport (A3)using Lower Support Pin(A4), insert cotter pin(A5) and bend ends.
Cotter pin
Arm pin outerposition for moreload on table
Arm pin innerposition for lessload on table
RIGHT SIDE SHOWNDo the same with left side symmetrically
8
6
7
Hid
de
nb
ed
TM
H10
Attach bunk bed slatcleat (6) to bunk bedside (4 ) using screw H10.
Attach body sides (1) to bottom stretcher (3), bunk bed side(4)and body back (5) fixed using dowels and screws H2.
Attach shelf stretcher (11) to shelf (10)using screws H14.
4
6
11
10
H14
5Attach concealer (2) tobody side (1) using screwsH10.
5
1
10
Hid
de
nb
ed
TM
11
Attach bed slats (14)to bunk bed slatsc l e a t s ( 6 ) u s i n gscrews H10.
A t t a c h f r o n tguardrail (7) to frontbunk bed side (4) .
7
Attach shelf to bodyback and screws H10,also attach shelf tobody side using screwsH2.
9
4
8
9
14
6
DESK ASSEMBLY
1
2
Attach Hiddenbed brand plate(A10) to desk back (18) with nails.
Attach desk back (18) to desktop (17) with Screws H2.
Label in place enablesmechanism warranty.
H2
17
18
3 Screw woodplugs (21) toinner side ofd e s k s i d e s(16).
21
H14
Hid
de
nb
ed
TM
Attach one of the desk sides(16) to the desk top(17) usingdowels and screws H2. Then insert wood plug into thedesk stiffener.
1918
H2
4
5 Attach the other desk side to the desk top using dowels andscrews H2 and inserting the wood plug into the deskstiffener.
16
17
16
H2
Hid
de
nb
ed
TM
6 Attach tube cover(20) to desk top(17) using screws H13.
18
17
19
H13
20
7 Attach the tribearer(A6) to the desk sides(16) using screwH6, H2 and H9.
16H2
H2H6
H9
BED ASSEMBLY
1 Insert the locks (A9) in due perforations in the bed head (10)and put Screws with screwdriver.
2 Attach front rail (12) and rear rail (13) to bed heads (10) withdowels and screws (H2).
Be careful, put cleats inside. Perforations for slats should bepointing bed up. (Down in sketch position!!)
10
10
12
10
Slats and salt cover must be attached to the bed after the bedwas attached to the body side.
H2
Hid
de
nb
ed
TM
FINAL ASSEMBLY
1 Assemble two links pivot sets attaching three link bushings toone triangle plate (outer cones to bushing) using link screws.
2
3
Put bed heads bearing on desk sides carefully, aligning holes(see detail in sketch STEP 2) provided for link bushings. Inboth sides in turn, place from outside the link pivot set intolink holes as shown. Slightly displacing or rising the bed asrequired to push the link in place.
Fix the remaining triangle plates (A7) with link screws to linkpivot. Tighten screws, re-check tightening all screws.
2
3
SLIGHTLY HEAVY - BE CAREFUL
Hid
de
nb
ed
TM
4 Slide body carefully in order to align plates with bed headholes. Then standing at rear side of the body, introducetrunnion bushing (A8) with the screw. Screw in a few turns,and let loose.
Hid
de
nb
ed
TM
5
H10
Place the bed cover over the slat cleat. Pull all screws(H10) through the bed slats (14) and through bed cover(11) to screw in slat cleat.
H10
14
11
6 Lift the bed slowly, taking care of keeping the desk inhorizontal position. Once in upper position, lock the bed bypushing in the Lock at both sides.
8a 8b 8c
PUSH INTO LOCK
CAUTION!1- EXTRA STRENGTH REQUIRED
We recommend to sit on the floorand pull strongly
2- TAKE CARE OF YOUR FINGERS
Do not put fingers in the hook.Hold the arm as shown.
7
Hid
de
nb
ed
TM
ASSEMBLY HAS FINISHEDFor Normal Use:
Check that the floor is clear to lower the bed.
Unlock to change from desk to bed position.
Stand at the middle of the furniture to pull from the bed beam and push
down the desk to make the transformation.
The mechanism is already calibrated to work with the mattress on and a
weight similar to 35/40 lbs. on the desk.
If the bed doesn't stay down by itself, add more weight on the desk.
www.hiddenbed.com