institut für physik der atmosphäre rayleigh-brillouin scattering experiment with atmospheric lidar...
TRANSCRIPT
Institut für Physik der Atmosphäre
Rayleigh-Brillouin Scattering Experiment with Atmospheric Lidar
from a Mountain Observatory
Oliver Reitebuch, Christian Lemmerz, Engelbert Nagel, Benjamin Witschas
Institut für Physik der Atmosphäre 33rd Lidar Working Group, Destin (FL), 2-4 Feb 2010
Up to now no direct measurement of Cabannes lineshape in the atmosphere performed; only indirect via wind or temperature measurement Challenging measurement because
difference between Gaussian and actual lineshape is only a few % (up to 10% at ground) => requires to sample lineshape in the order of 100 points
width of line is in the order 4 GHz FWHM to 6 GHz (total) at 355 nm => sampling with 50 MHz or 21 fm = 21*10-15 m
Challenges for atmospheric
lineshape measurements
-5000 -4000 -3000 -2000 -1000 0 1000 2000 3000 4000 5000
0,000
0,001
0,002
0,003
0,004
0,005
inte
nsity [a
.u.]
frequency [MHz]
Gauss + Mie Tenti + Mie
Scattering ratio =1.01
Measured lineshape is convolution of atmo-spheric spectra and instrumental function
=> Instrumental function has to be known with high accuracy => analysis with forward model or deconvo-lution is challenging for noisy measurements
Small bandwidth aerosol contribution "conta-minates spectra" significantly, because contribution is convoluted with instrumental function
Institut für Physik der Atmosphäre 33rd Lidar Working Group, Destin (FL), 2-4 Feb 2010
Measurement at a mountain observatory, because it is above aerosol-rich boundary layer especially during high pressure weather conditions in winter => no aerosol contamination possibility of horizontal line-of-sight measurement over distances of 20-30 km => horizontal averaging possible
Mountain observatory Schneefernerhaus UFS is at 2650 m ASL and 300 m below Zugspitze summit => ambient pressure from 705 hPa to 730 hPa during campaign, which should be large enough to see Brillouin effect
Only small Aerosol scattering disturbances will occur data of the German environmental agency (UBA) shows that the mean particle density on UFS is 500 p/cm3 compared to 60000 p/cm3 in the valley. Additional measurements from Microwave Radiometer of horizontal temperature profile and radiosondes from Innsbruck airport (30 km).
Where measuring the Brillouin effect in the atmosphere?
Institut für Physik der Atmosphäre 33rd Lidar Working Group, Destin (FL), 2-4 Feb 2010
Use ADM-Aeolus prototype lidar - the ALADIN airborne demonstrator A2D in horizontal pointing geometry with wavelength of 355 nm
Use of molecular Rayleigh channel with Fabry-Perot interferometer to measure lineshape:
drawback is very broad instrument function of 1.7 GHz compared to atmospheric width of 4 GHz (FWHM) or filter function of laboratory setup at VU Amsterdam with 0.23 GHz
Keep Fabry-Perot interferometer constant and change laser frequency in discrete steps over lineshape (calibration mode of ADM-Aeolus); monitor laser relative frequency with heterodyne unit and absolute frequency with wavemeter
Setup in laboratory together with H2O-Differential Absorption Lidar DIAL of FZK/IMK (Trickl, Vogelmann) during a period of 6 weeks in January to March 2009 More than 1000 kg of equipment was brought to the observatory by a cogwheel train
BRillouin Atmospheric INvestigation on Schneefernerhaus BRAINS 2009
Zugspitze2962 m
Institut für Physik der Atmosphäre 33rd Lidar Working Group, Destin (FL), 2-4 Feb 2010
0 2000 4000 6000 8000 10000
1400
1600
1800
2000
2200
2400
2600
2800
altitu
de
[m
]
distance from Schneefernerhaus [m]
Horizontal lidar measurements in nearly pure Rayleigh atmosphere are performed, and therefore averaging over all range gates is possible => increase SNR (assumption that p and T is constant is verified with MTP)
Hard Target measurements are possible over a range of 10 km to verify the instrument function with a Mie-type signal in addition to the internal reference signal
Horizontal LOS measurements of atmosphere and hard-target
DIAL
A2D
Institut für Physik der Atmosphäre 33rd Lidar Working Group, Destin (FL), 2-4 Feb 2010
844740000 844745000 844750000 844755000 844760000 844765000
100
200
300
400
internal reference
inte
nsi
ty [a
.u]
absolute frequency [MHz]844,740 844,745 844,750 844,755 844,760 844,765
0
100
200
300
400
500
inte
nsity
[a.u
]
absolut frequency [THz]
0 2000 4000 6000 8000 10000 120000
1000000
2000000
3000000
4000000
5000000
internal reference Airy fit Chi^2/DoF = 2672988684.57369R^2 = 0.99856 I0 5282893.3054 ±14693.9353FSR 13328.94598 ±340.00698FWHM 1634.76056 ±7.06055f0 6026.36317 ±2.25133
internal reference layer 5 layer 6 layer 7 layer 8 layer 9 layer 10 layer 11
inte
nsi
ty [a
.u]
frequency [MHz]
atmospheric calibrationf =50Mhz - 26.01.2009 - 17.12 o´clock
Atmospheric signal and internal reference for filter transmission is sampled with 240 frequency steps with f =50 MHz (21 fm) over a frequency range of 12 GHz (5.1 pm) 630 laser pulse returns with 60 mJ/pulse accumulated for every frequency step Some measurements were performed over 20 GHz with Δf = 50 MHz
Sampling of the atmospheric lineshape and instrument function
Institut für Physik der Atmosphäre 33rd Lidar Working Group, Destin (FL), 2-4 Feb 2010
Ongoing PhD thesis by Benjamin Witschas to develop method and analyse measurements from BRAINS
1) Develop accurate instrument function I(f) of the Fabry-Perot Interferometer => relevant for ADM-Aeolus
2) Atmospheric lineshape can be best modelled by Tenti S6: But this is an iterative algorithm, not a function, which can be analytically convoluted with instrument function in order to fit to measurements
3) Calculate expected difference between convolution of instrument function I(f) with Gaussian lineshape G(f)*I(f) and lineshape from Tenti S6 T(f)*I(f) => "fingerprint" of Brillouin scattering
4) Calculate difference between measured lineshape M(f) and Gaussian G(f)*I(f)
5) Compare expected difference (3) or "fingerprint" with measured difference (4)
The deviation between Gaussian model and Tenti simulation is up to 5 % and has a characteristic “fingerprint”.
844,750 844,752 844,754 844,756 844,758 844,760 844,762 844,7640,0
0,2
0,4
0,6
0,8
1,0
convolution Airy-Gauss convolution Airy-Tenti
inte
nsity [a
.u.]
absolute frequency [THz]
T = 253Kp = 511,9 hPay-parameter = 0,23FSR = 10921 MHzFWHM = 1647,84 MHz --> R = 0,62518
How to compare measurements with models?
844,735 844,740 844,745 844,750 844,755 844,760 844,765 844,770-0,04
-0,02
0,00
0,02
0,04
0,06
devi
atio
nfrequency [THz]
deviation Gaussian deviation Tenti
Institut für Physik der Atmosphäre 33rd Lidar Working Group, Destin (FL), 2-4 Feb 2010
844,745 844,750 844,755 844,760-0,06
-0,04
-0,02
0,00
0,02
0,04
0,06
0,08
844,745 844,750 844,755 844,760
-0,06
-0,04
-0,02
0,00
0,02
0,04
0,06
0,08
rel.
de
via
tion
(fit
an
d m
ea
sure
me
nt)
frequency [THz]
rel. deviation Layer 6 rel. deviation Layer 7 rel. deviation Layer 8 rel. deviation Layer 9 mean rel. deviation Layer 6 to 9 simulation rel. deviation with Gaussian distribution simulation rel. deviation with Tenit S6 distribution
844,745 844,750 844,755 844,760
-0,06
-0,04
-0,02
0,00
0,02
0,04
0,06
0,08
844,745 844,750 844,755 844,760
-0,06
-0,04
-0,02
0,00
0,02
0,04
0,06
0,08
rel.
de
via
tion
(fit
an
d m
ea
sure
me
nt)
frequency [THz]
rel. deviation Layer 6 rel. deviation Layer 7 rel. deviation Layer 8 rel. deviation Layer 9 mean rel. deviation Layer 6 to 9 simulation rel. deviation with Gaussian distribution simulation rel. deviation with Tenit S6 distribution
The deviations from measurement to Gaussian assumption and simulation with the Tenti S6 model to Gaussian assumption have the same characteristics.
The Tenti model de-scribes molecular scattered light (from gas in the kinetic regime) quiet well.
We have measured the effect of Brillouin scattering in the atmosphere the first time!
Is fingerprint of Rayleigh-Brillouin scattering measured?
Institut für Physik der Atmosphäre 33rd Lidar Working Group, Destin (FL), 2-4 Feb 2010
For the first time the lineshape from Rayleigh-Brillouin scattering was measured with high spectral resolution in the atmosphere Method to compare deviations of measurements from Gaussian lineshape and expected from Tenti S6 model was developed including convolution with instrument function Measurements confirm that the atmospheric lineshape deviates from a Gaussian as expected Lineshape and deviations can be modelled with Tenti S6 As an important secondary result an accurate description of the instrument function of the sequential Fabry-Perot interferometer for ADM-Aeolus was obtained:
pure Airy-function is not sufficient to describe filter transmission refinement of the model was performed including plate defects similar to an approach by McGill et al. (1997)
Next STEPS More than 50 spectral scans have been performed => analysis of spectra for different conditions, e.g. influence of Mie-scattering
Summary
Institut für Physik der Atmosphäre 33rd Lidar Working Group, Destin (FL), 2-4 Feb 2010
Excellent location for meetings