installer and user’s manual varanda awning · n°4 n°5 2 persons n°13 n°17! 1 variable number...
TRANSCRIPT
N°4N°5
2 persons
N°13N°17
!
1
Variable number
Ce
Sp
Cl
RtEb
Po1Po2 Eq
Bc
Installer and user’s manualVARANDA AWNING
INFORMATION PRE-INSTALLATION
Before the installation, check the leveling of the place where you will apply the awning. Dimensions should be parallels and levelled. In case the balcony is not level it's necessary an chock application to allow correctly the installation of the awning �xing plates.
Necessary tools
Inside package
Important
porch
2
B
A assembly
20cm max
100cm max
Sp
Cl
bottom
Make the same assembly to the other pro�le. Cl
3
Eq
Bc
assembly
Po1
top
A Disassemble B Assembly
C Slide the frontal pro�le on the fabric.
D Assembly again
N°4
100cm max
Fixing plates preparation
Awning and frontal pro�le preparation.
30cm mini
Cl
C
4
D E
F G
A B
30cm min
Cl
C D E
F
A B
Ø6x14mm
Ø6x14mm
support tubes
Adapt the awning �xation to the balcony type.
Balcony without tubes supports
Balcony with support tubes.
Attention, is necessary to respect the position described above represented for a awning set assembly. Adapt the awning �xation to the balcony type.
Fixation plates application.
attention, is necessary to respect the position described above represented for a awning set assembly.
5
Simple guide
Double guide
Balcony without supporting tubes.
Simple guide
Double guide
Others supports
Balcony with support tubes.
6
A
B C
Installation of safe
Placing the maneuver rope.6disassembleassemblyA
50cm
D
B face
front pro�le
winding direction
to C
B Face
to D
from B
-
CCover
!
D Front pro�le
B
Dto
from
OK
NO
P1
50cm
Eb
Cfrom
2
3to
RtPo2
1
to
from
3Po1
4
to
Ac
Ac
4from
to
for closure
5Po1
Eb
Po2
4
25
from 3
Ccover
Attention, for correct operation of the awning, pay close attention to the following statements. Operation to be carried out on the 2 reinforcements.
All respecting the winding direction, perform 3 courses of wire around the roller tube and pulley set. Pass the thread underneath the pulley P1 sliding it by the guide and �nding the bottom cover in C.
Po1 pulley must be placed in the middle of the front pro�le.
Preassembly 2 parts.
Attention from B to C ensure that the rope does not wind on her own, it can cause a break after much use.Then slide the rope by the pro�le, pass the rope through the pulley and make it slide again by the pro�le until the load bar.Attention: the placement of the cover will be made at the time of string stretched.
7
Assembly end
8
ClosureAwning open 30cm Opening
N°4N°4
7
Pull the end of the rope by hand and lock on release AC. The stretch should identify two sides to check that the pulley Po1 is well positioned in the center of the front pro�le. Ensure that the rope is guided on all the pulleys of the system. Open the awning down. Open the fabric 50cm, to perform another string tension. Make an opening maneuver and closing. The awning becomes tense.
The travel stops are pre-adjusted in factory. To adjust:- Unscrew the limit screw + or - to make the desired setting. Rotating + to get more closing or opening turning - to get less closing or opening.-Make a test.
After adjustments are made, put the safe cover again (paragraph 6) and the front cover pro�le (paragraph 3).
Fabric stretch
Regulation of the limit switches
Finishing
Information to the consumer
Awning maintenance advice
Problems Causes
Not install the awning in case of:
Wind Rain Snow Nothing suspended
Solutions
An awning is subject to some adverse situations: moisture, salt spray, balance, wind ...we recommend that:
- Check the tightening of the screws and the limit after installation and regularly at the beginning and end of each season.
-Never close a wet awning. Dry it if possible.
-Clean the fabric and the frame at the beginning and end of each season. Caution: never use detergents.
The awning balcony disintegrated from the structure.
The Mounting brackets are not adapted to the composition of the structure.
Check proper placement of the supports (according to the manual's instructions).In case of �xing with a chemical seal, report to the manufacturer.Check the entire circuit of the rope to �nd a possible shift of the rope. (Paragraph 6)Check if the voltage is identical in the 2 sides (sheave Po1 centered) (Paragraph 6)
Tighten the rope (Paragraph 7)
Do the full circuit of the rope again. paragraph 6Test the electrical part to �nd the problem.
Check the motor connectionCheck engine operation by connecting directly to the power input. (black or brown blue blue)
Wait the end of protection (20 minutes)
Incorrect voltage on the base.Fabric not stretched. (Natural e�ect)Rope break.Electrical maneuver faulty The engine is placed in thermal protection after 2 descents and a 1 rise successives.
Connection problem.
A Rope broke free of a pulley.The Tension of one rope is superior to another (double Po1 o�set)
The front pro�le does not work normally.
The fabric is not stretched.
The awning does not open or close.Electric awning maneuvers do not work.
Electric awning maneuvers do not work.
1 JSV03A
2 FUM42
3 TM40
4 CV03/CV02
5 PO16P
6 TO78
7 CV01
8 EO678P
9 CU14A
10 SV06A
11 PU807
12 SV05
13 EB0802
14 PU3704
15 TR19
16 PO20
17 PU3703
18 PO2102
N.R* AC02
N.R* C03
4
21
56 8
9
12
1516
1011
13
1718
7
*no represented part
14
3
SV35 SV3402 SV15A SV04 = 9mmSV14 = 13mmSV24 = 20mm
Exploded view
Aluminum parts
Engine bracket
Tubular motor
Safe cover
Pulley winding tube
Roller tube Ø78mm
Safe pro�le
Bushing Ø78mm
Roller tube support
Safe guide
Sliding pro�le
Front cover pro�le
Guide cover
Front pro�le’s cover
The fabric tension spring
Pulley to spring TR19
Front Pro�le
Tension pulley
Fixing the rope to the terminal pro�le
Rope
Number Reference Designation