installation specifications push a button heavy gauge ... draft in chimney and vigorous fire....
TRANSCRIPT
Large Flush Wood Hybrid-Fyre Insert
CLEAN BURNINGOnly .58
Grams Per Hour
K - Sidewall To Insert L - Side To Facing M - Top Facing N - Mantle O - Hearth Side* P - Hearth Depth*R - Mantel BreastplateS - Mantel ColumnT - Extension on HearthQ - Any Room Combustible* See Owner’s Manual for complete hearth clearances
AB
C
D
E
F
G
10-12 Hour
Burn Time
Heating Capacity Up to
2,500 Sq. Ft.*
3.0Cubic Foot
Firebox
Overall Efficiency
80.3%
EPA Phase IIApproved
0.58 Grams/Hour
Heavy GaugePlate Steel
Construction 5/16” & 1/4”
Kiln-Fired Masonry
Lined Firebox
* Heating capacity may vary depending on degree of home insulation, floor plan and ambient temperature zone of the area you live.
Installation We suggest that you have an authorized Fireplace Xtrordinair dealer install your fireplace insert. If you install the fireplace insert yourself, your authorized dealer should review your installation plans.
The Large Flush Wood Hybrid-Fyre Insert is designed for installation in masonry fireplaces and factory-built metal (Z.C.) fireplaces. Check with your local build-ing officials for any permits required for installation of this fireplace insert and notify your insurance company before proceeding with installation.
The Large Flush Wood Hybrid-Fyre Insert must be installed with Positive Flue (full chimney reline). See Owner’s Manual for details.
Because of the high performance this insert requires a non-combustible hearth.See your Owner’s Manual for details.
Testing Tested and certified by Intertek Laboratories Inc. Report #500346479PRT-001 Safety Tested to U. L. 1482 and ULC S628-1993
Minimum Fireplace Size A - Height (Front) B - Height (Rear) C - Width (Front) D - Width (Rear) E - Depth F - Hearth Depth G - Hearth Width
Surround Panels for Insert Designed to finish off the fireplace opening behind the face. No Trim.
Single Piece Panel Set - 42” Wide x 32-1/2” Height
Custom panel sizes available by special order.
Minimum Clearances toCombustibles
* Add 1-1/4” * * * when using* one-piece panel
Photos and illustrations are for descriptive purposes only. We reserve the right to improve or change our products without prior notification. Hybrid-Fyre™ and all other trademarks belong to Travis Industries, inc. Consult the Owner’s Manual for complete installation requirements. © Copyright T. I. 06/2012 Printed in the U. S. A. 98800568
See our complete line of fireplacesVisit us online: www.fireplacex.com
Installation SpecificationsAlways refer to the and use the Installation Manual for complete install information.
23-1/2” (597mm)22” (559mm)33” (839mm) (includes 2” for power cord)20-3/4” (528mm) 19” (483mm) 18” (458mm)* 47” (1093mm)
* See Owner’s * Manual for complete* hearth and R Value requirements
K N
M
O
P
LT
R
S
Q
www.fireplacex.com
Push A Button
Start Your Fire
The Revolutionary GreenStart ™ Igniter OptionStarting your woodstove has never been easier. Much like Charles Kettering’s invention of the electric automobile ignition 100 years ago, the GreenStart igniter system has evolved the ignition of fire in a spectacular way and has become the greatest innovation in wood heating in over 100 years.
Hot surface igniter blows 1400 degree heated air into firebox igniting the wood.
Igniter shuts down and blower continues to push air acting as a bellow to fan the fire.
Blower shuts down. Homeowner adjusts damper and air controls to maintain fire.
Blower continues to fan fire at various speeds to deliver proper draft in chimney and vigorous fire.
Starting a fire in your wood stove is now as convenient as pushing a button. No longer is the mess of starting a fire with matches and newspapers a concern as it has been eliminated entirely by this breakthrough new igniter system. Fireplace safety has increased, as well as there is no longer a need to leave doors
ajar to promote the fire start up.
The GreenStart system works much like a blacksmith bellows. A compressor forces 1400 degree preheated air into the firebox directly onto the wood source giving a clean fast smoke-free start up. This combination of the igniter and bellows is the brilliance of this design exclusively patented by Travis Industries. This system is also ideal for refreshing old fires as well by simply adding new fuel on top of the old coals, closing the door
and pushing the button again.
The new GreenStart system instantly elevates combustion temperatures within your stove, immediately establishes a draft and eliminates the slow and smoky typical wood fireplace start up. The GreenStart Igniter system will start wood burning within a minute. After the initial start up the compressor will continue pumping air at various speeds like a bellow into the fire greatly accelerating the start up time. After 15 minutes the compressor shuts off. For best results dry, seasoned wood is required when using the GreenStart system. Never before has starting a fire in a wood stove or insert been so simple.
6 -15 Minutes
6 Minutes
30 Seconds
15 MinutesUse your Smart Phone QR Reader to watch a video
on the GreenSmart Igniter
10-1/2” (267mm) 5-1/2” (140mm)37” (940mm)41” (1042mm)8” (204mm*18” (458mm)*37” (940mm)5-1/2” (140mm)0”36” (915mm)
13
11 12
10
10
176
45
3
28
9
Large Flush Wood Hybrid-Fyre™ Insert The Large Flush Hybrid-Fyre insert features the world’s cleanest burning wood technology combined with a huge fire
viewing area. Wood is the world’s most inexpensive fuel as well as a renewable resource. The Large Flush Wood Insert
uses a fusion of high performance wood combustion and catalytic technology in what we call Hybrid-Fyre technology.
Primary combustion occurs within the firebox. Secondary air is introduced through air tubes re-igniting the flue
gas as it leaves the firebox. Those same gases are then passed through a catalytic combustor to dramatically re-
duce emissions while at the same time increasing heat output and efficiency. With Hybrid-Fyre technology, virtually no
smoke exits the appliance. This super clean burning insert boasts emissions of only .58 grams an hour as well as almost
zero carbon monoxide output throughout all burn cycles. Because of it’s superior performance this large insert is
capable of heating up to 2,500 square feet, with up to a 12 hour burn time.
Large Flush Wood Hybrid-Fyre™ Insert
Metropolitan™ face
www.fireplacex.com
The Large Flush Wood Hybrid-Fyre insert is premium quality
with a long lasting value. The insert is American made
and created out of only the highest quality materials such
as heavy gauge steel (up to 5/16” thick), unibody firebox,
real masonry brick, stainless steel baffle and air tubes. All
of this contributes to the durability and longevity of the
product which is backed by Fireplace Xtrordinair’s “Real
World” Seven Year warranty.
Shadowbox™ face with concealed convection grills
Decorative Faces
Options
Metropolitan™ face with X and O patterned grills
Insert Wiring Kit
Allows you to hard wire any electrical connection within the firebox eliminating the power cord running across the hearth
Compared to any other large fireplace inserts on the market you will find the Large Flush Wood Insert your best choice - We Dare You To Compare!
• 80.5% Overall Efficiency. Tested to the Federal Govern-• ments proposed B4-15 Efficiency Standard. Efficiency is • averaged over all burn settings to give you “Real World” • performance. Don’t be fooled by over inflated efficiency • number used by other competitors.
• Hybrid-Fyre technology produces virtually 0% Carbon • Monoxide into the atmosphere.
• Built-in bypass damper allows for easy start-up of fire • and smoke-free reloading of wood.
• Approved for masonry and zero clearance fireplaces.
• Very clean appearance being entirely flush to the hearth.
• Firebox is 3.0 cubic feet in size and has the capacity to • accommodate a 24” log.
• Single cast iron door framing 319 square inches of glass allotting for a tremendous view of the fire.
• An unobstructed air wash system maintains the cleanliness • and clarity of the glass.
• Twin 90 CFM easily concealed fans come standard with • the insert greatly improving heat transfer.
• Option of adding the revolutionary GreenStart™ auto igniter.
Universal™ Face with vertical grills
Hybrid-Fyre™ TechnologyThe Large Flush Wood Insert is by far the cleanest burning, large insert available on the market. Featuring unparralled
craftsmanship and styling as well as the cutting edge science. This combination of the catalytic combustor and air tubes is
what creates this unique and ultra efficient Hybrid-Fyre™ technology.
(1) The super efficient combustion air is drawn into the preheated chamber converting cold, incoming air into warm combustion
air. (2) This air is then routed through the airwash channels and into the airwash which primarily keeps the glass very clean,
decreasing maintenance and adding convenience. (3) The air control regulates incoming air controlling the burn rate and is
then routed into the firebox by the primary combustion air (which helps to start the fire).
(4) The secondary air manifold
continues to route the air into
the secondary tubes which takes
the air to the secondary
combustion zone. (5) In this area,
any unburned particles are
re-ignited. (6) The Baffle slows
down the gases from being
expelled without one last clean
sweep from the catalytic
combustor (7) which reignites
all volatile gases. No particle
is left behind. This process
dramatically reduces emissions
and carbon monoxide output
making the Large Flush Wood
Insert a very ‘green’ fireplace.
(8) Room air is drawn through the
back convection chamber then circulated
through the convection channel where it is heated.
(9) This hot air is then expelled from the top convection chamber
through a large, cast-iron, heat sink increasing the temperature of the room.
(10) Additionally, twin 90 cfm fans push convection air through the stove greatly improving heat transfer and circulation into
the room. (11) A bypass damper is also included on the Large Flush Wood Insert, allowing for easy, smoke-free start ups. The insert comes standard with a 6” flue collar with internal attachment (12) for convienient installation as well as the the
optional GreenStart™ igniter, (13) making the start up process as easy as the push of a button.
Dare To Compare
13
11 12
10
10
176
45
3
28
9
Large Flush Wood Hybrid-Fyre™ Insert The Large Flush Hybrid-Fyre insert features the world’s cleanest burning wood technology combined with a huge fire
viewing area. Wood is the world’s most inexpensive fuel as well as a renewable resource. The Large Flush Wood Insert
uses a fusion of high performance wood combustion and catalytic technology in what we call Hybrid-Fyre technology.
Primary combustion occurs within the firebox. Secondary air is introduced through air tubes re-igniting the flue
gas as it leaves the firebox. Those same gases are then passed through a catalytic combustor to dramatically re-
duce emissions while at the same time increasing heat output and efficiency. With Hybrid-Fyre technology, virtually no
smoke exits the appliance. This super clean burning insert boasts emissions of only .58 grams an hour as well as almost
zero carbon monoxide output throughout all burn cycles. Because of it’s superior performance this large insert is
capable of heating up to 2,500 square feet, with up to a 12 hour burn time.
Large Flush Wood Hybrid-Fyre™ Insert
Metropolitan™ face
www.fireplacex.com
The Large Flush Wood Hybrid-Fyre insert is premium quality
with a long lasting value. The insert is American made
and created out of only the highest quality materials such
as heavy gauge steel (up to 5/16” thick), unibody firebox,
real masonry brick, stainless steel baffle and air tubes. All
of this contributes to the durability and longevity of the
product which is backed by Fireplace Xtrordinair’s “Real
World” Seven Year warranty.
Shadowbox™ face with concealed convection grills
Decorative Faces
Options
Metropolitan™ face with X and O patterned grills
Insert Wiring Kit
Allows you to hard wire any electrical connection within the firebox eliminating the power cord running across the hearth
Compared to any other large fireplace inserts on the market you will find the Large Flush Wood Insert your best choice - We Dare You To Compare!
• 80.5% Overall Efficiency. Tested to the Federal Govern-• ments proposed B4-15 Efficiency Standard. Efficiency is • averaged over all burn settings to give you “Real World” • performance. Don’t be fooled by over inflated efficiency • number used by other competitors.
• Hybrid-Fyre technology produces virtually 0% Carbon • Monoxide into the atmosphere.
• Built-in bypass damper allows for easy start-up of fire • and smoke-free reloading of wood.
• Approved for masonry and zero clearance fireplaces.
• Very clean appearance being entirely flush to the hearth.
• Firebox is 3.0 cubic feet in size and has the capacity to • accommodate a 24” log.
• Single cast iron door framing 319 square inches of glass allotting for a tremendous view of the fire.
• An unobstructed air wash system maintains the cleanliness • and clarity of the glass.
• Twin 90 CFM easily concealed fans come standard with • the insert greatly improving heat transfer.
• Option of adding the revolutionary GreenStart™ auto igniter.
Universal™ Face with vertical grills
Hybrid-Fyre™ TechnologyThe Large Flush Wood Insert is by far the cleanest burning, large insert available on the market. Featuring unparralled
craftsmanship and styling as well as the cutting edge science. This combination of the catalytic combustor and air tubes is
what creates this unique and ultra efficient Hybrid-Fyre™ technology.
(1) The super efficient combustion air is drawn into the preheated chamber converting cold, incoming air into warm combustion
air. (2) This air is then routed through the airwash channels and into the airwash which primarily keeps the glass very clean,
decreasing maintenance and adding convenience. (3) The air control regulates incoming air controlling the burn rate and is
then routed into the firebox by the primary combustion air (which helps to start the fire).
(4) The secondary air manifold
continues to route the air into
the secondary tubes which takes
the air to the secondary
combustion zone. (5) In this area,
any unburned particles are
re-ignited. (6) The Baffle slows
down the gases from being
expelled without one last clean
sweep from the catalytic
combustor (7) which reignites
all volatile gases. No particle
is left behind. This process
dramatically reduces emissions
and carbon monoxide output
making the Large Flush Wood
Insert a very ‘green’ fireplace.
(8) Room air is drawn through the
back convection chamber then circulated
through the convection channel where it is heated.
(9) This hot air is then expelled from the top convection chamber
through a large, cast-iron, heat sink increasing the temperature of the room.
(10) Additionally, twin 90 cfm fans push convection air through the stove greatly improving heat transfer and circulation into
the room. (11) A bypass damper is also included on the Large Flush Wood Insert, allowing for easy, smoke-free start ups. The insert comes standard with a 6” flue collar with internal attachment (12) for convienient installation as well as the the
optional GreenStart™ igniter, (13) making the start up process as easy as the push of a button.
Dare To Compare
13
11 12
10
10
176
45
3
28
9
Large Flush Wood Hybrid-Fyre™ Insert The Large Flush Hybrid-Fyre insert features the world’s cleanest burning wood technology combined with a huge fire
viewing area. Wood is the world’s most inexpensive fuel as well as a renewable resource. The Large Flush Wood Insert
uses a fusion of high performance wood combustion and catalytic technology in what we call Hybrid-Fyre technology.
Primary combustion occurs within the firebox. Secondary air is introduced through air tubes re-igniting the flue
gas as it leaves the firebox. Those same gases are then passed through a catalytic combustor to dramatically re-
duce emissions while at the same time increasing heat output and efficiency. With Hybrid-Fyre technology, virtually no
smoke exits the appliance. This super clean burning insert boasts emissions of only .58 grams an hour as well as almost
zero carbon monoxide output throughout all burn cycles. Because of it’s superior performance this large insert is
capable of heating up to 2,500 square feet, with up to a 12 hour burn time.
Large Flush Wood Hybrid-Fyre™ Insert
Metropolitan™ face
www.fireplacex.com
The Large Flush Wood Hybrid-Fyre insert is premium quality
with a long lasting value. The insert is American made
and created out of only the highest quality materials such
as heavy gauge steel (up to 5/16” thick), unibody firebox,
real masonry brick, stainless steel baffle and air tubes. All
of this contributes to the durability and longevity of the
product which is backed by Fireplace Xtrordinair’s “Real
World” Seven Year warranty.
Shadowbox™ face with concealed convection grills
Decorative Faces
Options
Metropolitan™ face with X and O patterned grills
Insert Wiring Kit
Allows you to hard wire any electrical connection within the firebox eliminating the power cord running across the hearth
Compared to any other large fireplace inserts on the market you will find the Large Flush Wood Insert your best choice - We Dare You To Compare!
• 80.5% Overall Efficiency. Tested to the Federal Govern-• ments proposed B4-15 Efficiency Standard. Efficiency is • averaged over all burn settings to give you “Real World” • performance. Don’t be fooled by over inflated efficiency • number used by other competitors.
• Hybrid-Fyre technology produces virtually 0% Carbon • Monoxide into the atmosphere.
• Built-in bypass damper allows for easy start-up of fire • and smoke-free reloading of wood.
• Approved for masonry and zero clearance fireplaces.
• Very clean appearance being entirely flush to the hearth.
• Firebox is 3.0 cubic feet in size and has the capacity to • accommodate a 24” log.
• Single cast iron door framing 319 square inches of glass allotting for a tremendous view of the fire.
• An unobstructed air wash system maintains the cleanliness • and clarity of the glass.
• Twin 90 CFM easily concealed fans come standard with • the insert greatly improving heat transfer.
• Option of adding the revolutionary GreenStart™ auto igniter.
Universal™ Face with vertical grills
Hybrid-Fyre™ TechnologyThe Large Flush Wood Insert is by far the cleanest burning, large insert available on the market. Featuring unparralled
craftsmanship and styling as well as the cutting edge science. This combination of the catalytic combustor and air tubes is
what creates this unique and ultra efficient Hybrid-Fyre™ technology.
(1) The super efficient combustion air is drawn into the preheated chamber converting cold, incoming air into warm combustion
air. (2) This air is then routed through the airwash channels and into the airwash which primarily keeps the glass very clean,
decreasing maintenance and adding convenience. (3) The air control regulates incoming air controlling the burn rate and is
then routed into the firebox by the primary combustion air (which helps to start the fire).
(4) The secondary air manifold
continues to route the air into
the secondary tubes which takes
the air to the secondary
combustion zone. (5) In this area,
any unburned particles are
re-ignited. (6) The Baffle slows
down the gases from being
expelled without one last clean
sweep from the catalytic
combustor (7) which reignites
all volatile gases. No particle
is left behind. This process
dramatically reduces emissions
and carbon monoxide output
making the Large Flush Wood
Insert a very ‘green’ fireplace.
(8) Room air is drawn through the
back convection chamber then circulated
through the convection channel where it is heated.
(9) This hot air is then expelled from the top convection chamber
through a large, cast-iron, heat sink increasing the temperature of the room.
(10) Additionally, twin 90 cfm fans push convection air through the stove greatly improving heat transfer and circulation into
the room. (11) A bypass damper is also included on the Large Flush Wood Insert, allowing for easy, smoke-free start ups. The insert comes standard with a 6” flue collar with internal attachment (12) for convienient installation as well as the the
optional GreenStart™ igniter, (13) making the start up process as easy as the push of a button.
Dare To Compare
Large Flush Wood Hybrid-Fyre Insert
CLEAN BURNINGOnly .58
Grams Per Hour
K - Sidewall To Insert L - Side To Facing M - Top Facing N - Mantle O - Hearth Side* P - Hearth Depth*R - Mantel BreastplateS - Mantel ColumnT - Extension on HearthQ - Any Room Combustible* See Owner’s Manual for complete hearth clearances
AB
C
D
E
F
G
10-12 Hour
Burn Time
Heating Capacity Up to
2,500 Sq. Ft.*
3.0Cubic Foot
Firebox
Overall Efficiency
80.3%
EPA Phase IIApproved
0.58 Grams/Hour
Heavy GaugePlate Steel
Construction 5/16” & 1/4”
Kiln-Fired Masonry
Lined Firebox
* Heating capacity may vary depending on degree of home insulation, floor plan and ambient temperature zone of the area you live.
Installation We suggest that you have an authorized Fireplace Xtrordinair dealer install your fireplace insert. If you install the fireplace insert yourself, your authorized dealer should review your installation plans.
The Large Flush Wood Hybrid-Fyre Insert is designed for installation in masonry fireplaces and factory-built metal (Z.C.) fireplaces. Check with your local build-ing officials for any permits required for installation of this fireplace insert and notify your insurance company before proceeding with installation.
The Large Flush Wood Hybrid-Fyre Insert must be installed with Positive Flue (full chimney reline). See Owner’s Manual for details.
Because of the high performance this insert requires a non-combustible hearth.See your Owner’s Manual for details.
Testing Tested and certified by Intertek Laboratories Inc. Report #500346479PRT-001 Safety Tested to U. L. 1482 and ULC S628-1993
Minimum Fireplace Size A - Height (Front) B - Height (Rear) C - Width (Front) D - Width (Rear) E - Depth F - Hearth Depth G - Hearth Width
Surround Panels for Insert Designed to finish off the fireplace opening behind the face. No Trim.
Single Piece Panel Set - 42” Wide x 32-1/2” Height
Custom panel sizes available by special order.
Minimum Clearances toCombustibles
* Add 1-1/4” * * * when using* one-piece panel
Photos and illustrations are for descriptive purposes only. We reserve the right to improve or change our products without prior notification. Hybrid-Fyre™ and all other trademarks belong to Travis Industries, inc. Consult the Owner’s Manual for complete installation requirements. © Copyright T. I. 06/2012 Printed in the U. S. A. 98800568
See our complete line of fireplacesVisit us online: www.fireplacex.com
Installation SpecificationsAlways refer to the and use the Installation Manual for complete install information.
23-1/2” (597mm)22” (559mm)33” (839mm) (includes 2” for power cord)20-3/4” (528mm) 19” (483mm) 18” (458mm)* 47” (1093mm)
* See Owner’s * Manual for complete* hearth and R Value requirements
K N
M
O
P
LT
R
S
Q
www.fireplacex.com
Push A Button
Start Your Fire
The Revolutionary GreenStart ™ Igniter OptionStarting your woodstove has never been easier. Much like Charles Kettering’s invention of the electric automobile ignition 100 years ago, the GreenStart igniter system has evolved the ignition of fire in a spectacular way and has become the greatest innovation in wood heating in over 100 years.
Hot surface igniter blows 1400 degree heated air into firebox igniting the wood.
Igniter shuts down and blower continues to push air acting as a bellow to fan the fire.
Blower shuts down. Homeowner adjusts damper and air controls to maintain fire.
Blower continues to fan fire at various speeds to deliver proper draft in chimney and vigorous fire.
Starting a fire in your wood stove is now as convenient as pushing a button. No longer is the mess of starting a fire with matches and newspapers a concern as it has been eliminated entirely by this breakthrough new igniter system. Fireplace safety has increased, as well as there is no longer a need to leave doors
ajar to promote the fire start up.
The GreenStart system works much like a blacksmith bellows. A compressor forces 1400 degree preheated air into the firebox directly onto the wood source giving a clean fast smoke-free start up. This combination of the igniter and bellows is the brilliance of this design exclusively patented by Travis Industries. This system is also ideal for refreshing old fires as well by simply adding new fuel on top of the old coals, closing the door
and pushing the button again.
The new GreenStart system instantly elevates combustion temperatures within your stove, immediately establishes a draft and eliminates the slow and smoky typical wood fireplace start up. The GreenStart Igniter system will start wood burning within a minute. After the initial start up the compressor will continue pumping air at various speeds like a bellow into the fire greatly accelerating the start up time. After 15 minutes the compressor shuts off. For best results dry, seasoned wood is required when using the GreenStart system. Never before has starting a fire in a wood stove or insert been so simple.
6 -15 Minutes
6 Minutes
30 Seconds
15 MinutesUse your Smart Phone QR Reader to watch a video
on the GreenSmart Igniter
10-1/2” (267mm) 5-1/2” (140mm)37” (940mm)41” (1042mm)8” (204mm*18” (458mm)*37” (940mm)5-1/2” (140mm)0”36” (915mm)
Large Flush Wood Hybrid-Fyre Insert
CLEAN BURNINGOnly .58
Grams Per Hour
K - Sidewall To Insert L - Side To Facing M - Top Facing N - Mantle O - Hearth Side* P - Hearth Depth*R - Mantel BreastplateS - Mantel ColumnT - Extension on HearthQ - Any Room Combustible* See Owner’s Manual for complete hearth clearances
AB
C
D
E
F
G
10-12 Hour
Burn Time
Heating Capacity Up to
2,500 Sq. Ft.*
3.0Cubic Foot
Firebox
Overall Efficiency
80.3%
EPA Phase IIApproved
0.58 Grams/Hour
Heavy GaugePlate Steel
Construction 5/16” & 1/4”
Kiln-Fired Masonry
Lined Firebox
* Heating capacity may vary depending on degree of home insulation, floor plan and ambient temperature zone of the area you live.
Installation We suggest that you have an authorized Fireplace Xtrordinair dealer install your fireplace insert. If you install the fireplace insert yourself, your authorized dealer should review your installation plans.
The Large Flush Wood Hybrid-Fyre Insert is designed for installation in masonry fireplaces and factory-built metal (Z.C.) fireplaces. Check with your local build-ing officials for any permits required for installation of this fireplace insert and notify your insurance company before proceeding with installation.
The Large Flush Wood Hybrid-Fyre Insert must be installed with Positive Flue (full chimney reline). See Owner’s Manual for details.
Because of the high performance this insert requires a non-combustible hearth.See your Owner’s Manual for details.
Testing Tested and certified by Intertek Laboratories Inc. Report #500346479PRT-001 Safety Tested to U. L. 1482 and ULC S628-1993
Minimum Fireplace Size A - Height (Front) B - Height (Rear) C - Width (Front) D - Width (Rear) E - Depth F - Hearth Depth G - Hearth Width
Surround Panels for Insert Designed to finish off the fireplace opening behind the face. No Trim.
Single Piece Panel Set - 42” Wide x 32-1/2” Height
Custom panel sizes available by special order.
Minimum Clearances toCombustibles
* Add 1-1/4” * * * when using* one-piece panel
Photos and illustrations are for descriptive purposes only. We reserve the right to improve or change our products without prior notification. Hybrid-Fyre™ and all other trademarks belong to Travis Industries, inc. Consult the Owner’s Manual for complete installation requirements. © Copyright T. I. 12/2012 Printed in the U. S. A. 98800568
See our complete line of fireplacesVisit us online: www.fireplacex.com
Installation SpecificationsAlways refer to the and use the Installation Manual for complete install information.
23-1/2” (597mm)22” (559mm)33” (839mm) (includes 2” for power cord)20-3/4” (528mm) 19” (483mm) 18” (458mm)* 47” (1093mm)
* See Owner’s * Manual for complete* hearth and R Value requirements
K N
M
O
P
LT
R
S
Q
www.fireplacex.com
Push A Button
Start Your Fire
The Revolutionary GreenStart ™ Igniter OptionStarting your woodstove has never been easier. Much like Charles Kettering’s invention of the electric automobile ignition 100 years ago, the GreenStart igniter system has evolved the ignition of fire in a spectacular way and has become the greatest innovation in wood heating in over 100 years.
Hot surface igniter blows 1400 degree heated air into firebox igniting the wood.
Igniter shuts down and blower continues to push air acting as a bellow to fan the fire.
Blower shuts down. Homeowner adjusts damper and air controls to maintain fire.
Blower continues to fan fire at various speeds to deliver proper draft in chimney and vigorous fire.
Starting a fire in your wood stove is now as convenient as pushing a button. No longer is the mess of starting a fire with matches and newspapers a concern as it has been eliminated entirely by this breakthrough new igniter system. Fireplace safety has increased, as well as there is no longer a need to leave doors
ajar to promote the fire start up.
The GreenStart system works much like a blacksmith bellows. A compressor forces 1400 degree preheated air into the firebox directly onto the wood source giving a clean fast smoke-free start up. This combination of the igniter and bellows is the brilliance of this design exclusively patented by Travis Industries. This system is also ideal for refreshing old fires as well by simply adding new fuel on top of the old coals, closing the door
and pushing the button again.
The new GreenStart system instantly elevates combustion temperatures within your stove, immediately establishes a draft and eliminates the slow and smoky typical wood fireplace start up. The GreenStart Igniter system will start wood burning within a minute. After the initial start up the compressor will continue pumping air at various speeds like a bellow into the fire greatly accelerating the start up time. After 15 minutes the compressor shuts off. For best results dry, seasoned wood is required when using the GreenStart system. Never before has starting a fire in a wood stove or insert been so simple.
6 -15 Minutes
6 Minutes
30 Seconds
15 MinutesUse your Smart Phone QR Reader to watch a video
on the GreenSmart Igniter
10-1/2” (267mm) 5-1/2” (140mm)37” (940mm)41” (1042mm)8” (204mm*18” (458mm)*37” (940mm)5-1/2” (140mm)0”36” (915mm)
BTU’s Per Hour(Cord Wood)
83,220