installation rear camera 2008 accord aii 37095-38880 … · 2017-10-10 · sectional view trunk lid...
TRANSCRIPT
Publications No.
INSTALLATIONINSTRUCTIONS
Accessory Application
© 2008 American Honda Motor Co., Inc. – All Rights Re
AII 37095-38880
REAR CAMERA ATTACHMENT KITserved. AII 37095-38880 (0
2008 ACCORD4-DOOR
802) 0
Issue Date
FEB 2008
PARTS LIST
Rear Camera Attachment KitP/N 08B77-TA0-100
Rear camera bracket
Rear camera trim
Rear camera harness
37 Wire ties
EPT sealer
2 Washer-screws, 4 x 14 mm
Grommet
2 Well-nuts
2 Wire ties with clip A
6-Pin connector
7 Wire ties with clip B
Template
4 Clips A
Clip B
4 Nuts
1 of 168B77-TA0-1000-91
2 Clips C
2 Tapes
Accessory User’s Information Manual
Rear CameraP/N 08A77-6K1-370
Rear camera
2 Screws, 3 x 6 mm
2 of 16 AII 37095-388
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Flat-tip screwdriver
Ratchet
8 mm and 10 mm Socket
Pushpin
Felt-tip pen
Drill
3 mm, 5 mm, 6 mm, 8 mm, and 10 mm Drill bit
Ruler
Eye protection (safety goggles, face shield, etc.)
10 mm Combination wrench
File
Diagonal cutters
Utility knife
Scissors
Center punch
Hacksaw blade
Touch-up paint
Electrical tape
Illustration of the Rear Camera Attachment Kit Installed on the Vehicle
7201010Y
REAR CAMERA HARNESS
REAR CAMERA
80 (0802) © 2008 American Honda Motor Co., Inc. – All Rights Reserved.
INSTALLATION
Install the backup camera first if both the backup camera and a trailer hitch are to be mounted on the vehicle.
1. Make sure you have the anti-theft codes for the radio and navigation system (if equipped), then write down the radio presets.
2. Disconnect the negative cable from the battery.
3. V6 MODEL only: Remove the passenger’s dashboard under cover (three clips and two pins).
Customer Information: The information in this instal-lation instruction is intended for use only by skilled tech-nicians who have the proper tools, equipment, andtraining to correctly and safely add equipment to yourvehicle. These procedures should not be attempted by“do-it-yourselfers.”
730101AY
PIN
CLIPS PASSENGER’S DASHBOARD UNDER COVER
PIN
© 2008 American Honda Motor Co., Inc. – All Rights Reserved. AII 37095-38
4. Release the glove box (damper and two stops).
5. Remove the glove box (two screws).
7112020Y
2 STOPS
DAMPER
GLOVE BOX
7112030Y SCREWS
GLOVE BOX
880 (0802) 3 of 16
6. Remove the right front side step trim (four clips).
7. Pull away the front door opening seal in the area shown.
8. Remove the right kick panel (two clips).
7125030E
4 CLIPS
RIGHT FRONT SIDE STEP TRIM
7115010E
2 CLIPS
FRONT DOOR OPENING SEAL
RIGHT KICK PANEL
4 of 16 AII 37095-388
9. Remove the rear seat cushion (one bolt and release the two hooks).
10. Remove the right seat side bolster (one bolt and release the one hook).
BOLTREAR SEAT CUSHION
HOOKS
HOOK
KNOB
7111030E
BOLT
REAR SEAT SIDE BOLSTER
HOOK
80 (0802) © 2008 American Honda Motor Co., Inc. – All Rights Reserved.
11. Remove the right rear side step trim (four clips).
12. Pull away the door opening seal in the area shown.
13. Remove the right center lower cover (one clip and four retaining tabs).
711601AE4 CLIPS
RIGHT REAR SIDE STEP TRIM
FRONT
7112050ECLIP
CENTER LOWER COVER
FRONT
RETAINING TAB
DOOR OPENING SEAL(Remove.)
© 2008 American Honda Motor Co., Inc. – All Rights Reserved. AII 37095-38
14. Fold down the rear seat back by pulling the lever under the rear parcel shelf inside the trunk.
15. Remove the trunk floor mat (one clip).
7220190E
LEVER(Pull.)
REAR SEAT BACK
Down.
REAR PARCEL SHELF
7109070E
CLIP
TRUNK FLOOR MAT
880 (0802) 5 of 16
16. Remove the rear trim panel (four clips and three hooks).
17. Remove the right trunk side lining (five clips).
710906AE
REAR TRIM PANEL
4 CLIPS
3 HOOKS
722018AE
RIGHT TRUNK SIDE LINING
3 CLIPS
2 CLIPS
6 of 16 AII 37095-388
18. V6 MODEL only: Remove the trunk lid lining (12 clips).
19. Remove four bolts and two clips from the license plate trim. Remove the license plate.
711502AE
TRUNK LID LINING
11 CLIPS
TRUNK LIDTRUNK LID
CLIP
751805AE
LICENSE PLATE TRIM
CLIPS (Reuse.)
4 BOLTS
80 (0802) © 2008 American Honda Motor Co., Inc. – All Rights Reserved.
20. Insert the KTC trim tool (AP201-W) between the license plate trim and the trunk lid. Move the tool left and right to peel off the double-sided tape in between.
21. Pull out on the license plate trim and disengage the lower three clips. Do not remove the license plate trim yet.
751806BE
LICENSE PLATE TRIM
DOUBLE-SIDED TAPE
TRUNK LID KTC TRIM TOOL (AP201-W)
762101AE
LICENSE PLATE TRIM
3 CLIPS
TRUNK LID
© 2008 American Honda Motor Co., Inc. – All Rights Reserved. AII 37095-38
22. Slide the license plate trim down, and disengage the top two clips to remove the license plate trim.
23. Remove and discard the top two clips from the trunk lid.
24. Using scissors, cut out the marked area for template A along the dotted lines.
711505BELICENSE PLATE TRIM
5 CLIPS(Discard.)
TOP CLIPS (Discard.)
Pull down and disengage the top two clips from the top of the license plate trim
7307120B
SCISSORS
TEMPLATE A
TEMPLATE
880 (0802) 7 of 16
25. Tape template A on the trunk lid as shown. Lightly center punch the trunk lid at each of the three marks indicated on template A. Remove template A.
26. While wearing eye protection, drill the trunk lid at each center-punched mark:
• Wrap each drill bit with electrical tape 15 mm from the tip, or use a drill stop.
• Drill all three center-punched marks to 8 mm. First drill with a 3 mm drill bit, then with a 6 mm drill, and finish with an 8 mm drill bit.
• Enlarge the bottom hole in the trunk lid to 10 mm using a 10 mm drill bit.
• Remove any burrs, and apply touch-up paint to each drilled hole. Allow the touch-up paint to dry before proceeding to the next step.
TEMPLATE A
VEHICLE HOLE
CENTER PUNCH
MARKTRUNK LID
MARKTAPE
TAPE
MARK
VEHICLE HOLE
7201041Y
MARK
ELECTRICAL TAPE (Wrap electrical tape around the drill bit.)
DRILL(3 mm bit 6 mm bit 8 mm bit))
15 mm
TRUNK LID
DRILL(3 mm bit 6 mm bit 8 mm bit 10 mm bit)
8 of 16 AII 37095-388
27. Install two well-nuts into the 8 mm holes.
28. Route the rear camera cord through the rear camera bracket, and install the rear camera to the rear camera bracket using the 3 x 6 mm screws.
7201051Y
8 mm HOLE
WELL-NUT
TRUNK LID
7201081Y
REAR CAMERA REAR CAMERA BRACKET
3 x 6 mm SCREW
REAR CAMERA CORD
3 x 6 mm SCREW
LABEL
80 (0802) © 2008 American Honda Motor Co., Inc. – All Rights Reserved.
29. Wrap the terminals of the rear camera cord with electrical tape.
30. Route the rear camera cord through the grommet. Secure the cord to the grommet with electrical tape at the indicated position. Note the direction of the grommet.
31. Route the rear camera cord through the 10 mm hole in the trunk lid and seat the grommet in the 10 mm hole.
32. Install the rear camera assembly to the trunk lid using the two 4 x 14 mm washer-screws.
7201091Y
ELECTRICAL TAPE (Wrap around the end of the grommet.)
REAR CAMERA
REAR CAMERA CORD
GROMMET
ELECTRICAL TAPE (Wrap around the terminals of the rear camera.)
TERMINALREAR CAMERA BRACKET
Align the grommet end with rear camera connector end.
CAMERA CONNECTOR END
720110AY
REAR CAMERA
GROMMET TRUNK LID
8 mm HOLE
4 x 14 mm WASHER-SCREW
10 mm HOLE
SECTIONAL VIEW
TRUNK LID
REAR CAMERA CORD
© 2008 American Honda Motor Co., Inc. – All Rights Reserved. AII 37095-38
33. Route the rear camera cord along the right side of the trunk lid, and remove the electrical tape from the terminals.
34. Remove the terminal lock from the 6-pin connector. Insert the rear camera terminals into the 6-pin connector. Verify each terminal position, and then reinstall the terminal lock. NOTE: Make sure to install the wires as shown in the illustration (do not match up the black and brown wires).
TRUNK LID REAR CAMERA CORD
REAR CAMERA CORD
ELECTRICALTAPE
TRUNK LID OPENER CABLEVEHICLE PANEL
VEHICLEHARNESS
YELLOW
WHITEBLUE/BLACK
BLUE/BLACK
BROWNBLACK
RED
YELLOW
WHITE
BLACKBROWNRED
LOCK
6 TERMINALS
6-PINCONNECTOR
6-PINCONNECTOR
YELLOWWHITE
RED
BLUE/BLACK
BROWN
BLACK
Viewed fromharness side
880 (0802) 9 of 16
35. Route the rear camera harness through the trunk lid hole, and plug the rear camera cord 6-pin connector into the rear camera harness 6-pin connector.
36. Secure the rear camera cord and the rear camera harness to the vehicle panel with three wire ties with clip B.
NOTE: If a trunk spoiler is installed, secure the rear camera cord to the trunk spoiler harness with two wire ties.
720112CY
WIRE TIE WITH CLIP B Insert into round hole.
6-PIN CONNECTOR
REAR CAMERA HARNESS
6-PIN CONNECTOR
WIRE TIE
TRUNK SPOILER HARNESS
REAR CAMERA HARNESS
WIRE TIE WITH CLIP B Insert into round hole.
WIRE TIE
TRUNK SPOILER HARNESS
WIRE TIE WITH CLIP B
10 of 16 AII 37095-388
37. Secure the rear camera cord to the vehicle harness with one wire tie.
38. Bundle up the excess rear camera cord, and secure it to the vehicle harness with one wire tie.
39. Using scissors, cut one EPT sealer in half. Attach half of the EPT sealer to the vehicle frame.
720113DY
VEHICLE HARNESS
REAR CAMERA CORD WIRE TIE
EPT SEALER (Cut in half.)
VEHICLE FRAME
TRUNK LIDREAR CAMERA CORD
80 (0802) © 2008 American Honda Motor Co., Inc. – All Rights Reserved.
40. Route the rear camera harness along the trunk lid hinge, and secure it to the holes in the hinge using four wire ties with clip B. NOTE: If a trunk spoiler is installed, secure the rear camera harness to the trunk spoiler harness using four wire ties.
41. Route the rear camera harness towards the rear of the vehicle, and secure it to the vehicle panel hole with one wire tie with clip A. NOTE: If a trunk spoiler is installed, secure the rear camera harness to the trunk spoiler harness with one wire tie.
720114BY
TRUNK SPOILER HARNESS
WIRE TIES WITH CLIP B
TRUNK LID HINGE
FRONT
GREEN TAPE
REAR CAMERA HARNESS
4 WIRE TIES
REAR CAMERA HARNESS
7201151Y
VEHICLE PANEL
FRONT
REAR CAMERA HARNESS
WIRE TIE WITH CLIP A
REAR CAMERA HARNESS
WIRE TIEGREEN TAPETRUNK SPOILER HARNESS
GREEN TAPE
TRUNK LID HINGE
© 2008 American Honda Motor Co., Inc. – All Rights Reserved. AII 37095-38
42. Route the rear camera harness towards the rear of the vehicle, and secure it to the vehicle panel hole with one wire tie with clip A. NOTE: If a trunk spoiler is installed, secure the rear camera harness to the trunk spoiler harness with one wire tie.
730713BB
FRONT
WIRE TIE
REAR CAMERA HARNESS
WIRE TIE WITH CLIP A
VEHICLE PANEL
REAR CAMERA HARNESS
TRUNK SPOILER HARNESS
TRUNK LID HINGE
880 (0802) 11 of 16
43. Route the rear camera harness along the vehicle harness, and secure it to the vehicle harness with six wire ties.
44. Route the rear camera harness forward along the vehicle harness towards the front of the vehicle, and secure it to the vehicle harness with one wire tie.
720116BY
REAR CAMERA HARNESS
FRONT
WIRE TIES VEHICLE HARNESS WIRE TIES
WIRE TIES
VEHICLE HARNESS
TRUNK
7201170Y
FRONT
REAR CAMERA HARNESS
WIRE TIE
VEHICLE HARNESS
TRUNK
12 of 16 AII 37095-388
45. Route the rear camera harness forward along the vehicle harness, and secure it to the vehicle harness with four wire ties.
46. Route the rear camera harness forward past the “B” pillar, and secure it to the vehicle harness with three wire ties.
7201181Y
FRONT
REAR CAMERA HARNESS
WIRE TIES
VEHICLE HARNESS
WIRE TIES
REAR SEAT
7201191Y
FRONT
REAR CAMERA HARNESS
WIRE TIES
VEHICLE HARNESS
GREEN TAPE
REAR CAMERA HARNESS
VEHICLE HARNESS WIRE
TIE
REAR CAMERA HARNESS
“B” PILLAR
80 (0802) © 2008 American Honda Motor Co., Inc. – All Rights Reserved.
47. Route the rear camera harness through the passenger’s door opening, and secure it to the vehicle harness with five wire ties.
48. Route the rear camera harness up through the glove box opening, and secure it to the vehicle harness with five wire ties.
72
FRONT
REAR CAMERA HARNESS
WIRE TIE
VEHICLE HARNESS
GREEN TAPE
WIRE TIE
VEHICLE HARNESS
3 WIRE TIES
REAR CAMERA HARNESS
PASSENGER’S SEAT
7201211Y
REAR CAMERA HARNESS
WIRE TIES VEHICLE HARNESS
WIRE TIES
VEHICLE HARNESS
VEHICLE CLIP
VEHICLE HARNESS
GLOVE BOX OPENING
© 2008 American Honda Motor Co., Inc. – All Rights Reserved. AII 37095-38
49. At the glove box opening, locate and remove the tape securing the 6-pin vehicle connector.
50. Plug the 6-pin vehicle connector into the rear camera harness 6-pin connector. Secure the 6-pin connector to the vehicle harness with one wire tie.
51. Using scissors, cut out the marked area for template B along the dotted lines.
720122AY
REAR CAMERA HARNESS
WIRE TIE
VEHICLE HARNESS
6-PIN CONNECTOR
6-PIN CONNECTOR
TAPEGLOVE BOX OPENING
VEHICLE HARNESS
7307120B
SCISSORS
TEMPLATE B
TEMPLATE
880 (0802) 13 of 16
52. Attach template B to the license plate trim using tape.
53. Using a pushpin, mark the license plate trim at the five locations.
54. Using a utility knife, scribe along the inner line of template B, and peel off the template.
730801AB
TEMPLATE BLICENSE PLATE TRIM
TAPE
TAPE
RIB
RIB
730802BB
LICENSE PLATE TRIM
PUSHPIN
MARK
UTILITY KNIFE
MARKPUSHPIN
TEMPLATE B
INNER LINE
4 mm
4 mm
14 of 16 AII 37095-388
55. While wearing eye protection, drill the license plate trim at each mark.
• First drill all five holes with a 3 mm drill bit, and then with a 6 mm drill bit.
• Enlarge just the bottom holes to 10 mm using a 10 mm drill bit.
56. Using a hacksaw blade, cut away the license plate trim along the scribe mark made in step 54.
57. Using a utility knife, cut out the rib from the license plate trim as shown.
730803AB
MARK
LICENSE PLATE TRIM
DRILL(3 mm bit 6 mm bit)
MARK
DRILL(3 mm bit 6 mm 10 mm bit)
730804BB
MARK
LICENSE PLATE TRIM
HACKSAW BLADE
Cut out the marked area.
RIB
Cut out.
UTILITY KNIFE
80 (0802) © 2008 American Honda Motor Co., Inc. – All Rights Reserved.
58. Install the rear camera trim in the cutout made in the license plate trim.
59. Using a felt-tip pen, mark the license plate trim at the ends of each double-sided tape.
60. Remove the double-sided tape from the license plate trim. (Use 3M General Purpose Adhesive Cleaner, 3M #08984.)
730805AB
REAR CAMERA TRIM
LICENSE PLATE TRIM
HOLE
751401AE
DOUBLE-SIDED TAPE(Remove.)
LICENSE PLATE TRIM
FELT-TIP PEN
MARK
DOUBLE-SIDED TAPE
SCRIBE LINES
© 2008 American Honda Motor Co., Inc. – All Rights Reserved. AII 37095-38
61. Install four clips A, one clip B, and four nuts to the li-cense plate trim.
62. Using isopropyl alcohol on a shop towel, clean the license plate trim between the marks you made. Remove the adhesive backing from the double-sided tape, and attach the tape between the marks in the scribe line areas.
63. Fit the rear camera into the rear camera trim, and reinstall the license plate trim. Reinstall the two clips and four bolts.
720128AY
CLIP B
4 NUTS
LICENSE PLATE TRIM
4 CLIPS A
DOUBLE-SIDED TAPES
DOUBLE- SIDED TAPEMARK
ADHESIVEBACKING(Remove.)
ADHESIVEBACKING(Remove.)
720129AY
LICENSE PLATE TRIM
HOLE
REAR CAMERA
CLIPS
880 (0802) 15 of 16
64. Check that all wire harnesses and cables are routed properly and that all connectors are plugged in.
65. Reinstall all removed parts.
66. Reconnect the negative cable to the battery.
67. Enter the anti-theft codes for the radio and navigation systems (if equipped), then enter the customer’s radio presets.
68. Reset the clock.
69. Check operation of the rear camera system according to the Accessory User’s Information Manual provided with the rear camera.
16 of 16 AII 37095-388
80 (0802) © 2008 American Honda Motor Co., Inc. – All Rights Reserved.