installation instructions & warranty leaflet d02173 … · installation instructions & warranty...
TRANSCRIPT
-
INSTALLATION INSTRUCTIONS & WARRANTY LEAFLET
* Center 4mm FP Corner Entry 760x760x1850* Center 4mm FP Corner Entry 800x800x1850* Center 4mm FP Corner Entry 900x900x1850
D02173.D02174.D02175.
-
Please familiarise yourself with the fitting instructions beforecommencing fitting.
1 Check that you have the tools required2 Check that the installation site is compatible with size of door supplied3 Check all the enclosure components4 Check that the installation kit is complete
DO NOT ALL 4 boxesas satisfactory.The wall plugs supplied with the installation kit are for use in solid walls.Hollow or ‘stud-partition’ walls will require alternative fixings. Please consult a hardware supplier for the correct type.It may also be necessary to consult your tiling supplier about the correctmethod for drilling your tiles.
attempt to install the product unless you can tick
3.0mm
6mm
IMPORTANT
-
2
Box Contents:
1xInstallation Instruction.
[1] 4xHorizontal Rails. 8xScrews ST4x35.
[13] 2xHandle Sets.
[12] 4xGlass Clamps. 4xScrews ST3.5x8.
[2] 6xWall Plugs.[3] 6xScrews ST4x35.
[15] 2xMagnetic Seals .
[8] 2xFixed Panels.
[7] 2xCorner Connectors. 4xScrews ST3.5x8. 4xScrew Cover Caps.
[14] 4xWater Deflectors.
[6] 2xWall Posts.
[9] 2xDoor Panels.
[10] 4xTop Rollers.[11] 4xBottom Rollers.
[16] 4xProfile Covers.
[4] 12xScrews Cover Caps.
[5] 6xScrews ST3.5x8.
-
Assembly Drawing
3
[4]
[3]
[5]
[6]
[12]
[14]
[9]
[1]
[16]
[13]
[1]
[2]
[8]
[7]
[15]
[16]
[10]
[11]
Number Description Picture Quantity Can be purchased separately Wolseley Spare Product code
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
4
6
14
16
14
2
2
2
2
4
4
4
2
4
2
4
Horizontal Rails
Wall Plugs
Screws ST4x35
Screws Cover Caps
Screws ST3.5x8
Wall Posts
Corner Connectors
Fixed Panels
Door Panels
Top Rollers
Bottom Rollers
Glass Clamps
Handle Sets
Water Deflectors
Magnetic Seals
Profile Covers
N
N
N
Y
N
N
N
N
N
Y
N
Y
N
/
/
/
/
/
/
/
/
D03091
/
D03082
/
D03097
D03093Y
D03098Y
-
SIZE(mm) A
760x760
800x800
730-750
770-790
Adjust The Size
4
A A
900x900 870-890
A
A
-
Installation Steps:Step 1
Step 2
Glass ClampGlass Clamp
Please pay attention to the direction!
Screw ST3.5x8
View from inside
2b
[6]
[8]
[1]
[12]
[3]
Screw ST4x35
6mm
[2] [3]
The profile must be checked with the spirit level whilst marking.
[4]
with screw cover
Screw ST4x35
2b 2b
5
[4]
-
Step 3
Step 4
View from inside
1b
1a
1
2
21
1
2
Screw ST3.5x8
2
[7]
[5]
[6][8]
View from inside
1
2
[10]
[11]
[9]
Top Roller.
Top Roller.
Bottom Roller.
6
[4]
-
Step 5
Step 6
Fixed Panel Door Panel
Ensure wall profiles are plumb. Adjust enclosure to be square and level. Wheels should be adjusted to square the doors and ensure smooth running.
2 33 2
3
1
1
[13]
[15]
[14]
7
-
1 1
Step 7
Step 8
View from inside
1a
1b
1c
Max: 3.0mm!
Screw ST3.5x8
View from inside
[5]
[4]
[16]
Take extra care not to drill through to exterior side.
with screw cover
Follow the indications on wall profiles to locate the drilling holes
8The sealant should be applied to the outside edge.
[4]
-
Safety Information for User & InstallerImportant information for fitter:Installation information• It is recommended that only approved/qualified plumbers should install the product.• Incorrect installation of the enclosure will invalidate guarantee.
Safety information prior to and during installation• Carefully check the product for transport damage prior to installation. • Never install damaged panels as there is a risk of spontaneous glass breakage.• The supplied fixings/wall plugs are only for mounting directly on solid walls. • It is essential that the solid, masonry/walls be inspected for adequate load-bearing capacity prior to every installation.• The supplied fixings/wall plugs are not for use with stud walls such as plaster board, wood, metal or fiber board.• Always seek professional advice to confirm wall type and appropriate type of fixing to be used for installation.• Always check walls for concealed utility lines (power, gas, and water) prior to drilling the fixing holes. • Ensure that fittings will not hinder the movement of the door as this may cause glass breakage.• For hinge/pivot doors ensure that toilet bowls, wash-stands or other objects are outside of the door opening area.
Special information on handling glass• Always protect all glass edges from damage.• Never stand the glass on its corners throughout the installation! Place the packing material beneath the glass panel; never place the glass on tiles, concrete floors or similarly hard surfaces• It is mandatory to check each glass panel for damage prior to installation. Never install damaged glass panels as this could cause spontaneous glass breakage!• If the glass panel is damaged during use it must be replaced without delay. (Failure could cause a risk of spontaneous glass breakage!)
Prevent damage to glass or operation of the product. • Ensure fittings do not hinder the movement of the door. • Ensure that no objects are within the range of the door opening/ closing area. • Avoid hitting the panels with hard objects such as mops when cleaning or tools during assembly. Damaged panels must be replaced as failures may cause latent glass breakage.• Do not hit against the glass edge with hard or pointed objects (e.g. with mop handle) Damaged panels must be replaced; damage may cause spontaneous glass breakage.• Do not use panels or handles to hang or support items such as drying towels or clothes.
Hazard information for special groups of people• Do not allow small children, sick or disabled persons to shower unattended.• A strong magnet is attached in the closing profile of some of the panels. This magnet could affect a pacemaker. Keep a minimum distance of 15 cm from the magnet. Consult insulation guide for location of magnets.
Maintenance InformationService/repair and inspection required for safety• After cleaning, check all the moving elements are sufficiently greased, re-grease, if necessary. Only use acid-free grease. We recommend silicone grease or standard household Vaseline.
Cleaning Do not use steam cleaners, caustic or aggressive cleaning and scouring agents, cleaners that corrodeplastics, or solvents containing acetone or turpentine or neat bleach.• Do not use any cleaning agents, which according to the manufacturer's specifications may corrode aluminum or light alloys. • Do not use glass cleaning pastes and micro-fiber cloths to prevent damage to glass coating system.• In order to prevent the build-up of lime scale, remove any remaining drops of water after showering using a squeegee, soft cloth without any cleaning agent.• After use, carefully rinse off all residue such as; liquid soaps, shampoos, shower gels or similar cosmetic product with water to avoid deposits.
Important: Never apply the cleaning agent for longer than necessary. After cleaning, check all the moving elements are sufficiently greased, re-grease, if necessary.
-
Helpline
Should you require any technical help in association with your CENTER
products please call with your query.0344 292 7062
Warranty: Years
For detail warranty information, please visit our website:
www.wolseley.co.uk
5
Wolseley CV34 6DY
www.wolseley.co.uk
页 1页 2页 3页 4页 5页 6页 7页 8页 9页 10页 11NAO1142 (A1).pdf页 4
NAO1142 (A2).pdf页 4