installation instructions rp11-d pendantrp11-d series direct shielding1 lumen package2 cri/ cct...
TRANSCRIPT
NULITE Lighting Inc. 10770 East 51st Avenue Denver, CO 80430 Phone (303) 287-9646 www.nulite-lighting.com
WARNINGS:•Do not assemble continuous run on the ground and lift into place. Joints will distort and not create a tight fit. Joining hardware will have to be purchased and replaced.
•Risk of electrical shock or fire, disconnect power during installation or servicing. Read all instructions completely before starting installation. Install and wire in accordance to all national and local codes by a certifi ed electrician. Fixture may be sharp, handle with care. Let fixture cool before main-tenance.
AVERTISSEMENTS •Risque d’électrocution ou d’incendie. Déconnectez l’alimenta-tion durant l’installation ou la maintenance. Lisez attentivement toutes les instructions avant de commencer toute installation. Faites installer et câbler selon les normes Nationales et Lo-cales par un électricien certifi é. Les installations peuvent être coupantes, à manipuler avec précaution. Laissez refroidir les installations avant une opération de maintenance.
ADVERTENCIA Riesgo de descarga eléctrica oun incendio, desconecte la alimentación durante la instalación o servicio. Leer todas las instrucciones completas antes de empesar la instalación. Instalar y cablear en acuerdo a las reglas nacionales y códigos locales por un electricista certifi cado. El accesorio puede estar agudo, agarre con cuidado deje que el acessorio. Enfriar antes de mantenimiento.
Page 1DISTORT JOINT
Installation InstructionsRP11-D Pendant
SURFACE MOUNT /DRIVER ENCLOSURE Mounting Option “SR”
ENLIGHTED SENSOR NOTES AND DETAILS ON PAGE 2
NULITE Lighting Inc. 10770 East 51st Avenue Denver, CO 80430 Phone (303) 287-9646 www.nulite-lighting.com
Page 2
Installation InstructionsRP11-D Pendant
SURFACE MOUNT /DRIVER ENCLOSURE Mounting Option “SR”
.XXX: - (303)287-9646
SCALE: 1:2 REV.:
SYMMETRICAL
DBS SMALL ENLIGHTED0.003" SHEET 1 OF 2
Crit. Dim. 10770 E 51st Ave. - Denver.005"
PART IS NOT
Unless Otherwise Specified: FINISH
Angles: - CO
MATERIAL
1
Hole Location 0.005"Hole Size
A
•Nulite product provided with Enlighted wireless occupancy / daylight sensor as shown•Sensor and lighting system to be calibrate and commisioned by certified Enlighted technican•Sensor electronics are contained within luminaire and do not have any impact to standard contractor wring procedure notated on pages 5,6 and 7
NULITE Lighting Inc. 10770 East 51st Avenue Denver, CO 80430 Phone (303) 287-9646 www.nulite-lighting.comNULITE Lighting Inc. 10770 East 51st Avenue Denver, CO 80430 Phone (303) 287-9646 www.nulite-lighting.com
Page 3
Package ContentsLuminaireIncludes Factory installed 4 conductor low voltage power cord (48” or 120”)
Installation InstructionsSero / Qūb Pendant
SURFACE MOUNT Mounting Option “SR”
NULITE Lighting Inc. 10770 East 51st Avenue Denver, CO 80430 Phone (303) 287-9646 www.nulite-lighting.com September 2018
Page 2
***Every luminaire will have a companion driver enclosure, not all luminaires and driver enclosures are the same, please be sure to pair the proper driver enclosure to the proper luminaire by reading the packaging labels***
Package Contents• Luminaire• Includes factory installed 4 conductor
low voltage power cord (48” Aircraft Cable = 78” Power Cord 120” Aircraft Cable = 150” Power Cord)
• Includes factory installed aircraft cable adjuster(s)
Package Contents• Driver enclosure for surface mounting
applications• Power Canopy Hardware Packet
• (1) Metal cord crimp• (1) Zip tie• (1) 48” or 120” aircraft cable
1. LUMINAIRE
2. SURFACE MOUNTED DRIVER ENCLOSURE
3. NON-POWER MOUNT HANGING HARDWARE
Package Contents• Non-Power Canopy Hardware Packet
• (1) 3” diameter canopy• (1) Stainless Steel aircraft cable
coupler• (1) 48” or 120” aircraft cable
NOTE: Non-Power canopy hardware is only necessary for individual and row starter luminaires
3”48” or 120”
1. LUMINAIRE
Installation InstructionsRP11-D Pendant
SURFACE MOUNT /DRIVER ENCLOSURE Mounting Option “SR”
NULITE Lighting Inc. 10770 East 51st Avenue Denver, CO 80430 Phone (303) 287-9646 www.nulite-lighting.com
Installation InstructionsSero / Qūb Pendant
SURFACE MOUNT Mounting Option “SR”
NULITE Lighting Inc. 10770 East 51st Avenue Denver, CO 80430 Phone (303) 287-9646 www.nulite-lighting.com September 2018
Page 3
Unit Lengths
26 1/4” (667mm)
Individual
Continuous Row
Driver
Enclosure
50 1/4” (1276mm)
74 1/4” (1886mm)
98 1/4” (2496mm)
26 1/4” (667mm)
50 1/4” (1276mm)
74 1/4” (1886mm)
98 1/4” (2496mm)
Unit Lengths
26 1/4” (667mm)
Individual
Continuous Row
Driver
Enclosure
50 1/4” (1276mm)
74 1/4” (1886mm)
98 1/4” (2496mm)
26 1/4” (667mm)
50 1/4” (1276mm)
74 1/4” (1886mm)
98 1/4” (2496mm)
2 1/4”
4 1/4”
4 1/4”
2 1/4”
SERO
QuB
2 1/4”
10 1/2”9 ”
2 1/4”
22”
9 ”NULITE 10770 EAST 51ST AVE DENVER, CO 80239 / P 303 287 9646 / NULITE-LIGHTING.COM ©2019 ALL RIGHTS RESERVED 1
DATE: PROJECT:
CATALOG #: TYPE: QTY:
1 1/2” (40 mm)
1 5/8” (42 mm)
REGOLO 1
RP11Direct
Pendant / Flush LensRemote Driver
RP11-D
SERIES DIRECT SHIELDING1 LUMEN PACKAGE2 CRI/ CCT CIRCUIT5
RP11-D - Regolo 1.5" wide, 1" tall direct remote pendant
FF - Flush Frosted 03 - 250 lm/ft05 - 500 lm/ft08 - 750 lm/ftXX3
L30 - 80 CRI, 3000KL35 - 80 CRI, 3500KL40 - 80 CRI, 4000KH30 - 90 CRI, 3000KH35 - 90 CRI, 3500KH40 - 90 CRI, 4000KTW4 - Dynamic white tuning from 2700k to 6500K with a CRI of 90
1C - Single Circuit1E - Single Circuit with EM Circuit1B6 - Single Circuit with 6W Battery Pack1B10 - Single Circuit with 10W Battery Pack
Notes:1. Consult factory for additional options2. Nominal lumen output for 3500K3. Consult factory for custom lumen package4. Tunable white requires TWV 0-10V or TWD Dali eldoLed DUALdrive driver5. In order to have a battery or emergency circuit, luminaire is required to be ≥4'. Consult factory for additional options.6. Consult factory for specifications and custom dimming options. See page 2 for additional information7. Specify run length in 6" increments
• Micro-scale functional pendant luminaire that provides unlimited lighting possibilities for creative design.
• Precision cut extruded aluminum housing. Housing standard finish is electrostatically applied textured white powder coat paint. Optional silver, black, or custom color paint finishes.
• Distributed LED array in a variety of lumen output packages. LED color is available in 3000K, 3500K or 4000K with a CRI of 80 or 90. Custom outputs are available. Module is replaceable. L90≥100,000 hrs. Tunable white utilizes 50% 2700K and 50% 6500K diodes with a CRI of 90.
• Innovative high reflective acrylic lens assembly reduces internal components and utilizes a metal core PCBA that snaps into place. Removable for maintenance. Optimizes thermal management.
RP11-D (Flush Frosted Lens)100% Downlight
ORDERING INFORMATION SAMPLE NUMBER: RP11-D-FF-05L35-1C-U-D-WW-T1/120-4
Light Output and Energy Consumption*
Light Level lm/ft Watts/ft Efficacy03 274.5 2.6 105.605 526.5 4.8 110.308 750.3 7.1 105.7Lumen output may vary. 3500K used for above results.
VOLTAGE DRIVER6 LUMINAIRE FINISH
MOUNTING / SUSPENSION LENGTH (IN INCHES)
LENGTH OPTIONS1
U - Universal Dimming 0-10vD - Dim to 1% (Standard)D0 - Dim to 1%, fade to offD02 - Eldoled Solodrive, dims to 0%Tunable WhiteTWV - 0-10V Eldoled Dualdrive, dims to 0%TWD - DALI Eldoled Dualdrive, dims to 0%
DALI DimmingELE - Eldoled Ecodrive, dims to 1%ELS - Eldoled Solodrive, dims to 0%Lutron DimmingL11 - Lutron HiLume™ Premier, dims to 0.1%L12 - Lutron HiLume™ 2-Wire 120V Forward Phase, dims to 1%L15 - Lutron HiLume™ H-Series, dims to 1%L16 - Lutron HiLume™ 5-Series, dims to 5%
W - White (Standard)S - SilverB - BlackCC1 - Custom Color
Grid Ceiling T1 / 48 T1 / 120T9 / 48 T9 / 120 TS / 48 TS / 120
Sheet Rock Ceiling GP / 48 GP / 120 Ceiling Surface SR / 48 SR / 120
2 - 2 ft3 - 3 ft4 - 4 ft5 - 5 ft6 - 6 ft7 - 7 ft8 - 8 ftXX7 - x ft
N - NightlightDS - Daylight sensorOS - Occupancysensor GTD - Generator transfer deviceGLR - FusingETS - Electronic transfer switch
CANOPY FINISH
W - White (Standard)B - Black
2”(51mm)
10.5”(267mm)
9”(229mm)
2”(51mm)
10.5”(267mm)
9”(229mm)
2”(51mm)
10.5”(267mm)
9”(229mm)
2”(51mm)
10.5”(267mm)
9”(229mm)
48” or 96”
48” or 96” 48” or 96” 48” or 96”
Individual
Continuous Row
Installation InstructionsRP11-D Pendant
SURFACE MOUNT /DRIVER ENCLOSURE Mounting Option “SR”
Page 4
NULITE Lighting Inc. 10770 East 51st Avenue Denver, CO 80430 Phone (303) 287-9646 www.nulite-lighting.com
Page 5
Installation InstructionsSero / Qūb Pendant
SURFACE MOUNT Mounting Option “SR”
NULITE Lighting Inc. 10770 East 51st Avenue Denver, CO 80430 Phone (303) 287-9646 www.nulite-lighting.com September 2018
Page 4
Remove the security screw from the wiring box cover. Lift open the wiring box cover.
Remove wiring box cover and disconnect the driver wiring harness from the wiring box. Set cover aside.
1 2
3
INSTALL DRIVER ENCLOSURE/ POWER MOUNT
Installation InstructionsRP11-D Pendant
SURFACE MOUNT /DRIVER ENCLOSURE Mounting Option “SR”
NULITE Lighting Inc. 10770 East 51st Avenue Denver, CO 80430 Phone (303) 287-9646 www.nulite-lighting.com
Page 6
Installation InstructionsSero / Qūb Pendant
SURFACE MOUNT Mounting Option “SR”
NULITE Lighting Inc. 10770 East 51st Avenue Denver, CO 80430 Phone (303) 287-9646 www.nulite-lighting.com September 2018
Page 5
Connect line voltage flex to wiring box. Connect line voltage leads to wiring harness. Black (Hot), Green (Ground), White (Neutral).
Feed braided silver fixture cord through hole Connect low voltage wires from fixture cord as shown.
4 5
76
8 9
Mount wiring box to structure at the indicated holes. Mounting hardware by others.
Remove knockout for line voltage.
If Dimming is required make dimming wire connections.
Blue
Blue / white stripe
Red / white stripe
Red
WhiteGreen
Gray (Dim)
Black
Purple (Dim)
Installation InstructionsRP11-D Pendant
SURFACE MOUNT /DRIVER ENCLOSURE Mounting Option “SR”
Installation InstructionsSero / Qūb Pendant
SURFACE MOUNT Mounting Option “SR”
NULITE Lighting Inc. 10770 East 51st Avenue Denver, CO 80430 Phone (303) 287-9646 www.nulite-lighting.com September 2018
Page 6
Tuck all wires into the wiring box and re-attach the cover by reversing steps 1 & 2.
Tighten security screw with screwdriver.
(A) Thread outer and inner coupler onto aircraft cable. (B) Align cable assembly with threaded stem and thread coupler onto threaded stem. (C) Thread outer coupler to inner coupler.
Wiring box installation is complete.
Reconnect the wiring harness from the drivers on the wiring box cover.
Secure braided fixture cord with cord-crimp provided.Cinch tight with pliers.
10 11
13
1514
12
NULITE Lighting Inc. 10770 East 51st Avenue Denver, CO 80430 Phone (303) 287-9646 www.nulite-lighting.com
Page 6
Installation InstructionsRP11-D Pendant
SURFACE MOUNT /DRIVER ENCLOSURE Mounting Option “SR”
NULITE Lighting Inc. 10770 East 51st Avenue Denver, CO 80430 Phone (303) 287-9646 www.nulite-lighting.com
INSTALLING AN INDIVIDUAL OR ROWSTARTER LUMINAIRE
Screw threaded coupler and non-power canopy onto mount-ing stem to physically hang luminaire
16
Page 7
2”(51mm)
10.5”(267mm)
9”(229mm)
2”(51mm)
10.5”(267mm)
9”(229mm)
48” or 96”
Individual
Make non-power mount structural connection
Installation InstructionsRP11-D Pendant
SURFACE MOUNT /DRIVER ENCLOSURE Mounting Option “SR”
Attach aircraft cable to integral luminaire adjuster on both power and non-power side as necessary
Pull cable through luminaire and level, snip excess cable if necessary
Re-attach lens assembly by first pulling back end cap (held by spring) then snapping into place
10
11 12
ATTACH AIRCRAFT CABLES ON POWER AND NON-POWER SIDES
Before installing aircraft cables remove lens assembly with provided tool or flathead screwdriver
9
Installation InstructionsRP11-D Pendant
SURFACE MOUNT /DRIVER ENCLOSURE Mounting Option “SR”
2”(51mm)
10.5”(267mm)
9”(229mm)
2”(51mm)
10.5”(267mm)
9”(229mm)
48” or 96”
Individual
Page 8
Installation InstructionsRegolo RP13 Pendant
V/Indirect, D/Direct, B/Bi-DirectSheet Rock, Grid, and Surface Structure Mount
NULITE Lighting Inc. 10770 East 51st Avenue Denver, CO 80430 Phone (303) 287-9646 www.nulite-lighting.com March 2019 Page 7
After the“starter” or“ mid” is fully secured with two hanging points, then make power connection and mount the next luminaire, then join them together as shown below and secure with two torsion spring latches that are integrated into the luminaire.
11 12
SNAP!
Connect the strap to the hole in the catch tray. Collapse the alignment strap back to its original position to lock the two fixtures together.
109
Insert alignment tabs from the next fixture into the slots on the current fixture.
Release the alignment strap from the current fixture and extend the catch tray from the next fixture.
7 8
Dislodge the lens/LED board assembly from the bottom of the luminaire and let it hang by the support chains.
Connect male electrical connector from next fixture to female connector on the current fixture.
inStaLLing a row-mid or row-end (aFter Starter haS been inStaLLed, Step 1 -6 From page 3, 4, or 5)
JOINING FIXTURES ***Illustrations depict RP13 integral driver product, that is identical to the RP11D with regard to mechanical connection (alignment sleeves and spring latch), but RP11D does not have feed through power***
NULITE Lighting Inc. 10770 East 51st Avenue Denver, CO 80430 Phone (303) 287-9646 www.nulite-lighting.com
Page 9
13 14
15 16
RP11D does not have through wire electrical connec-tion
Installation InstructionsRP11-D Pendant
SURFACE MOUNT /DRIVER ENCLOSURE Mounting Option “SR”
2”(51mm)
10.5”(267mm)
9”(229mm)
2”(51mm)
10.5”(267mm)
9”(229mm)
48” or 96” 48” or 96” 48” or 96”
Continuous Row