Page 1 www.hysecurity.com © 2019 P/N MX002608, MX002646, MX002728, MX002849, MX4171 D0486 Rev E

Installation Instructions MX002608, MX002646, MX002728, MX002849, MX4171

Adding a Second Traffic Light (M30/M50)The StrongArm Crash Traffic Light Option can be mounted in four different locations: two mounts exist on the Pivot post and two mounts exist on the Catch post. If you attach the traffic light to the Catch post, you will need:

• To drill through the Entrapment shield (see illustration)

• To feed additional wire through conduit to the Pivot post’s Smart Touch Controller

(STC) board.

Tools Needed• Pipe wrench or large Channel Locks, Electrical tape, Needle-nose pliers

• Phillips-head screwdriver, 1/2, 9/16 & 7/16-inch box end & socket wrenches

• 1/2-inch drill bit

NOTE: Catch post mount requires additional wire.

CAUTION

Turn OFF power to the StrongArm operator and take the necessary precautions to avoid electrical shock.

Assemble the Traffic LightRefer to the illustration, while you take the following steps:

1. Open the traffic light access panels and tape the spade ends of the wires.

2. Feed the wire through pipe. 3. Secure the pipe inside the traffic light access panel using the large

locknuts and washers provided. Refer to the illustration.4. Remove the Pivot post’s front panel. To access the traffic light

mounting holes, use a 7/16-inch socket and remove the cover plate from the chassis.

5. Feed wires through chassis and secure traffic light assembly.

Wire

Elbow

Bracket

Feed wires through hole in chassis. Secure traffic light assembly.

5

Traffic light

4

StrongArm M30 Pivot & Catch Posts shown

Front Panel

Pivot post

Use ½-inch bit to drill 3 holes through shield & mount traffic light.

Entrapment shield

C/L

Dist: 4.125 in (11 cm)

Dist: 2.06 in (5 cm)

Drill holes through shield

Clearance holefor wire

Assemble the Traffic Light per the illustrations. Two different pole mounts exist.

MX002849 MX002608

a. Open Traffic Light access panels.

b. Unwrap and feed wires through pipe.

c. Secure pipe to Traffic Light with threaded lock nuts.

Four bolt mount

Tri-stud washer with fasteners (3 washers & nuts)

Two bolt mount

Yello

w

Alu

min

um

32

1

Page 2 www.hysecurity.com © 2019 P/N MX002608, MX002646, MX002728, MX002849, MX4171 D0486 Rev E

Assemble the Traffic Light, continued

To connect the traffic light wires to the Smart Touch Controller (STC) board, take the following steps:

6. Route the wire to the STC. Plug the bundled wires MX002646 (provided in the kit) into their matching wires coming from the STC and Power Module. Match the wire color and connect female to male (or vice versa).

NOTE: You may need to unplug the wires from the existing traffic light and reattach them to the wire harness.

7. Plug the opposite ends of the wires into the matching wire harness coming from the traffic lights. One set of black, white, and red wires for one traffic light. The other set of black, white, and red wires into the other set of wires for the other traffic light.

8. Neatly arrange wires and making sure all are securely fastened.9. Turn the main power to the operator ON and cycle the operator

open and close to test that the traffic lights are working properly.

MaintenanceFor maintenance or troubleshooting issues, refer to the operator’s product manual. If you do not have a copy of the manual, it is available on the HySecurity website at www.hysecurity.com.

Technical SupportFor Technical Support, call your installer or authorized HySecurity distributor. Obtain the serial number of your operator before calling. For the name of a distributor near you, call HySecurity at 800-321-9947.

For information about HySecurity training for installers, maintenance personnel and end users, refer to the company website at www.hysecurity.com.

Reset

Smart Touch ControllerSecurityHy ®

Reset

Smart TTTTTTTTTTTTTouch Coouchuchhh Ccch Coucuch CCuch Coouchuch Couch Cohouch Coouch Coch Couch Cohh Couch Coouch Coouch Ccchhouch CoCCCCuch CCooouch Cooch Coooo ch Ch Cochh Cooouch Coh Chh CCuu Conntrollennttttntrttntntntttrntrtntnntrttrrttt rSecuritycurityuritriitySecurittyyyyyyyyHyHHyyyHHyyHHyyySS ®

Conduit between posts

Wire ties available for securing wires.

Disconnect single traffic light wires and reattach wire bundle for the two traffic lights.

Wire bundle: MX002646

Connect the wire harness to the single black, white, and red wires coming off the STC board or power module. Make sure the wires match to their same colored counterparts.

Bundle the opposite ends into two sets of one black, one white, and one red wire and connect them to the matching wires coming from the traffic lights.

Smart Touch Controller

7

8

6

Power Supply Terminal Blocks

NOTE: Only traffic light wiring shown.

(+24V) (-24V)

BLACKTERMINAL BLOCKS

REDTERMINAL

BLOCKS