installation instructions* for french door bottom freezer ... · requires water supply access. ......
TRANSCRIPT
DO NOT REMOVE this label until the refrigerator has been leveled. Please follow all instructions for leveling your refrigerator.
P/N: 242062402
2
1
7Doors□ Handles are secure and tight□ Door seals completely to cabinet on all sides□ Fresh food doors are levelLeveling□ Refrigerator is level, side to side and tilted ¼ inch (6 mm) front to back□ Toe grille is properly attached to refrigerator□ Cabinet is sitting solid on all cornersElectrical Power□ House power turned on□ Refrigerator plugged in
Installation Check List
Preparing For InstallationBe sure to coordinate site preparation and installation with your kitchen contractor.Include these minimum guidelines in your site preparation: • Chooseaplacenearagroundedelectricaloutlet. • Donotuseanextensioncordoranadapterplug. • Avoiddirectsunlightandcloseproximitytoarange,
dishwasher or other heat source. • Floorshouldbelevelandabletosupportafully
loaded refrigerator. • Therefrigerator’sIceDispenser
requires water supply access. • Planforeasyaccesstocountertops
when removing food. • Forcompleteaccesstodrawersand
freezer baskets, doors must be able to fully open.
• Loadrefrigeratorfromsideofcabinetonly.
• Donotrunretainingstrapsoverhandlesnorovertightenstraps. • Neveruserefrigeratorhandlestomovetherefrigerator.Allowthefollowingclearancesforeaseofinstallation,properaircirculation, and plumbing and electrical connections: Sides & Top: 3/8 inch / Rear: 1 inch
Level Refrigerator
6 Frigidaire uses packing foam and tape to secure the internal parts of your refrigerator for shipping. Once the refrigerator is in position, you can remove this material.
What’s Next?Congratulations! You are ready to begin enjoying your new Frigidaire refrigerator. • Forimportantsafetyinstructionsandtolearnhowtooperateyourrefrigerator,pleaseread
the entire Use & Care Guide. • Youmaywanttostartwiththe“NormalOperatingSights&Sounds”sectionoftheGuideto
learnwhattoexpectduringtypicaloperation. • Pleaseregisteryourproduct.Youcanregisteronlineatwww.frigidaire.comoryoucan
simply send in the Registration Card.Guidelines for final positioning of your refrigerator • Allfourcornersofthecabinetmustrestfirmlyonthe
floor. • Thesidesshouldtilt¼inch(6mm)fromfrontto
back (to ensure that doors close and seal properly). • Doorsshouldalignwitheachotherandbelevel.Most of these conditions can be met by raising or lowering the adjustable front rollers.
To level the cabinet using the front rollers: 1 You can raise or lower each door. Use a 3/8 inch socket
wrench to turn the adjustment screws (1 per side). To raise: turn adjustment screw clockwise. To lower: turn adjustment screw counterclockwise. 2 Ensure both doors are bind-free with their seals
touching the cabinet on all four sides and that cabinet is stable.
3 Afterunitisleveled,loweranti-tipleguntilitcontactsthefloor.
To Connect Water Supply Line To Ice Maker Inlet Valve 1. Disconnect refrigerator from electric power source. 2. Place end of water supply line into sink or
bucket.TurnONwatersupplyandflushsupply line until water is clear. Turn OFF water supply at shutoff valve.
3. Remove plastic cap from water valve inlet and discard cap.
4. If you use copper tubing - Slide brass compression nut, then ferrule (sleeve) onto water supply line. Push water supply line into water valve inlet as far as it will go (¼ inch). Slide ferrule (sleeve) into valve inlet and fingertightencompressionnutontovalve.Tighten another half turn with a wrench; DO NOT overtighten. See Figure 1.
If you use stainless steel tubing - The nut and ferrule are already assembled on the tubing. Slide compression nut onto valve inletandfingertightencompressionnutonto valve. Tighten another half turn with a wrench; DO NOT overtighten. See Figure 2.
5. With steel clamp and screw, secure water supply line (copper tubing only) to rear panel of refrigerator as shown.
6.Coilexcesswatersupplyline(coppertubingonly), about 2½ turns, behind refrigerator as shown and arrange coils so they do not vibrate or wear against any other surface.
7. Turn ON water supply at shutoff valve and tighten any connections that leak.
8. Reconnect refrigerator to electrical power source.
9. To turn ice maker on, lower wire signal arm (freezericemaker)orsettheicemaker’sOn/Offpowerswitchtothe“ON”position(freshfood ice maker).
BeforeInstallingTheWaterSupplyLine,YouWillNeed: • BasicTools:adjustablewrench,flat-bladescrewdriver,and
PhillipsTM screwdriver • Accesstoahouseholdcoldwaterlinewithwaterpressure
between 30 and 100 psi. • Awatersupplylinemadeof¼inch(6mm)OD,copper
or stainless steel tubing. To determine the length of tubing needed, measure the distance from the ice maker inlet valve at the back of the refrigerator to your coldwaterpipe.Thenaddapproximately7feet,sotherefrigerator can be moved out for cleaning.
• Ashutoffvalvetoconnectthewatersupplylinetoyourhousehold water system. DO NOT use a self-piercing type shutoff valve.
• Acompressionnutandferrule(sleeve)forconnectingacopperwatersupplylinetotheice maker inlet valve.
*Please refer to your Use & Care Guide for more details.
Connect Water Supply
Ice Maker
□ House water supply connected to refrigerator□ No water leaks present at all connections □ Ice Maker is turned ON.Final Checks
□ Shipping material removed□ Fresh Food and Freezer temperatures set
3
Raise
Lower
Anti-tipLeg
DoorDoor
If you are not satisfied with the installation of your refrigerator, please contact the store where you purchased it or call 1-800-944-9044 for assistance.
Installing & Leveling Freezer Drawer (if necessary)4
Remove Internal Shipping Materials
Installation Instructions* for French Door Bottom Freezer/Refrigerator
WARNINGTo avoid electric shock, which can cause death or severe personal injury, do not connect your refrigerator to an electrical power source until you have completed Step 2 of these instructions.
CAUTION• Shifting the refrigerator from side to side
may damage flooring.• Do not block the toe grille on the lower
front of your refrigerator. Sufficient air cir-culation is essential for proper operation.
IMPORTANTIf you are installing your refrigerator without connecting it to a water supply,makesuretheicemaker’spower switch is turned Off (see the Use & Care Guide for more details).
NOTEIfyouneedtoremovethedoorstogetyourrefrigeratorintothehouse,pleasereferto“RemovingDoors”in the Use & Care Guide. These installation instructions are provided only as a possible customer option. Frigidaire recommends that you use a service or kitchen contracting professional to install your refrigerator.
NOTECheck with your local building authority for recommendations on water lines and associated materials prior to installing your new refrigerator. Depending on your local/state building codes, Frigidaire recommends for homes with existingvalvesitsSmartChoice® water line kit 5305513409 (with a 6 ft. Stainless Steel Water Line)andforhomeswithoutanexistingvalve,Frigidaire recommends its Smart Choice® water line kit 5305510264 (with a 20 ft. Copper Water Linewithself-tappingsaddlevalve).Pleasereferto www.frigidaire.com for more information.
CAUTIONRoom temperatures below 55°F (13°C) or above 110°F (43°C) will impair cooling ability of your refrigerator’s compressor.
NOTEPlease call 1-800-944-9044 if you need assistance with this installation.
WARNINGTo avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator from elec-trical power before con-necting a water supply line to the refrigerator.
CAUTIONTo Avoid Property Damage:• Copper or Stainless Steel braided tubing is recommended for the wa-
ter supply line. Water supply tubing made of ¼ inch (6 mm) plastic is not recommended to be used. Plastic tubing greatly increases the potential for water leaks, and the manufacturer will not be respon-sible for any damage if plastic tubing is used for the supply line.
• Do not reuse compression fitting or use thread seal tape.• DO NOT install water supply tubing in areas where temperatures fall
below freezing.• Chemicals from a malfunctioning softener can damage the ice maker.
If the ice maker is connected to soft water, ensure that the softener is maintained and working properly.
Plastic Water Tubing to Filter
Copper water linefrom household water supply
(Include enough tubing in loop to allowmoving refrigerator out for cleaning.)
Ferrule(Sleeve)
Copperwater line
Wate r Valve
Valve Inlet
Water ValveBracket
SteelClampPlastic Water
Tubing toFilter Brass
CompressionNut
Figure 1
Figure 2
®
Remove Hex
Head Drawer
Screw
Remove Hex
Head Drawer
Screw
Do Not Remove
Other Screws
Remove Hex
Head Drawer
Screw
Remove Hex
Head Drawer
Screw
Do Not Remove
Other ScrewsA. Checkgasketsealaroundtop,bottom,
and sides of freezer drawer.B. If gasket is not sealed, open drawer
and slightly loosen 4 drawer screws (2 on each side) to allow drawer to rotate.
C. Close drawer and recheck the seal onthegasket(A).Openthedrawergrabbing by the sides in the center (B). Be careful not to rotate the drawer.
D. Tighten 4 drawer screws.E. Recheck gasket seal.F. Installthetoegrillebyfitting
into place.
Pull Drawer Out
From Both Sides
Grab DrawerAt Center
ThenPush AgainstFreezer Drawer
A B
1.Installingfreezerdrawer:Referto“InstallingFreezerDrawer”intheUse&CareGuide.2.Levelingfreezerdrawer:
Installing & Adjusting Doors (if necessary)5
Raising/Lowering Door
OpenDoor90
degrees
Bottom of Door
Opening Door
1.Installingdoors:Referto“InstallingDoors”intheUse&CareGuide.
2.Doorsfinaladjustmentusingtheadjustable lower hinge (select models, if necessary):
A. Opendoorsto90degrees.B. Liftthedoorwhileadjusting
the washer. To raise the door: rotate
washer clockwise. To lower the door: rotate
washer counterclockwise.
www.goedekers.com