IMAGING SOLUTIONS INC. Original Equipment Manufacturer

Installation Instructions for

Door Jamb Cameras 20K152-F / 20K142-F

Prior to Using This Document: Videology reserves the right to modify the information in this document as necessary and without notice. It is the user’s responsibility to be certain they possess the most recent version of this document by going to www.videologyinc.com, searching for the model number, and comparing revision letters on the respective document, located in the document’s footer. For technical assistance with this product, please contact the supplier from whom the product was purchased.

Videology Imaging Solutions, Inc. USA Videology Imaging Solutions, B.V. Europe

37M Lark Industrial Parkway Greenville, RI 02828 Tel: 401-949-5332 Fax: 401-949-5276 www.videologyinc.com

Neutronenlaan 4 NL-5405 NH Uden, Netherlands Tel: +31 (0) 413-256261 Fax: +31 (0) 413-251712 www.videology.nl

Doc # INS-20K1X2-F Issue Date: 03/17/2011 Revision: A Page 1 of 6

Table Of Contents 1. Document History ................................................................................................................. 2 2. Features: ............................................................................................................................. 2 3. Dimensions .......................................................................................................................... 2 4. Installation:.......................................................................................................................... 3 5. Camera Connections.............................................................................................................. 4 6. Specifications ....................................................................................................................... 4 7. Important Safety Instructions ................................................................................................. 5 8. Important Safeguards:........................................................................................................... 5 9. Contact Information .............................................................................................................. 6

1. Document History

Revision Issue Date Reason CN# Rev A 03-17-2011 Initial release 11-0031

2. Features: Resolution Choice of either 520 or 400 TVL 48 Wide Angle 5.5mm lens Standard BNC/ Power Pin connections Available in Stainless Steel & OEM options Power requirement 5 VDC @ 0.8 Watts (Power supply not included)

3. Dimensions

Doc # INS-20K1X2-F Issue Date: 03/17/2011 Revision: A Page 2 of 6

4. Installation: An installation template is provided to assist in the installation of the mullion camera. (70V0850) Note: Mullion depth must be a minimum of 1.75” so the unit can operate without interference.

1. Locate a spot at 5 1/2 feet AFF (above finished floor). Attach the enclosed template (70V0850) to the mullion with the center of the cutout at this spot.

2. Using a #36 drill (0.11”), drill the two mounting holes (if needed) and the two faceplate holes for

the camera.

3. Using a Dremel tool cut-out the center of the template.

4. Using a rat-tail file de-burr and touch up the edges of the rectangular hole. Run the power and video cables down the inside of the mullion.

5. If using a 24VAC to 5VDC connector (60BIP5), make sure all electrical connections are protected

from shorting to the metal frame of the door. (It is recommended that the conversion from 24VAC to 5VDC be done outside of the mullion casing.)

6. Attach the cables to the camera.

Note: Cables for the 20K152-F are routed out of the bottom of the camera. Cables for the 20K142-F are routed out of the top of the camera.

7. Carefully, insert the camera into the mullion. Using the 2 mount holes, fasten the camera to the mullion.

8. Power up the camera and check the image.

Use the adjustment lever on the rear of the camera to shift the field of view right or left as needed. Once field of view is acceptable, mount the camera and attach cover plate. 20K142-F shown

Doc # INS-20K1X2-F Issue Date: 03/17/2011 Revision: A Page 3 of 6

Doc # INS-20K1X2-F Issue Date: 03/17/2011 Revision: A Page 4 of 6

5. Camera Connections Video Output BNC connectors used to connect the camera to a monitor or digital video recording system.

Power Input DC 5V input (Power supply not included)

6. Specifications Electrical

20K152-F High Resolution

20K142-F Standard Resolution

Image Sensor 1/4” IL CCD Resolution 520 TVL 400 TVL Sensitivity < 0.5 lux < 0.25 lux Signal to Noise Ratio 50 dB (AGC off) Video Output Composite 1Vp-p CVBS (75 ohms) Power supply * 5VDC ±5%

* CAUTION Not polarity protected at board level. Using the supplied connector mitigates this risk of flying leads

Power consumption < 0.8W Mechanical

Dimensions W x H x D 39mm x 112mm x 41mm (1.5” x 4.4” x 1.6”) Weight (w/cable) 95.5g (3.37oz) Lens 3.7mm F2.0 fi xed pinhole cone Accessories

Cover plate (brushed stainless) Included 2.1mm power jack & shielded BNC video cable

60PBIP5 24VAC to 5VDC adapter Not Included 60P5VDC 5VDC power supply

Environmental

Operating Temperature -15°C ~ 55°C (5°F ~ 131°F) Operating Humidity 20 up to 93%RH Storage Temperature -25°C ~ 70°C (-13°F ~ 158°F) Storage Humidity Up to 98%RH Lifetime MTBF > 150000 hrs Packaging ESD safe package

7. Important Safety Instructions

CAUTION RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: To reduce the risk of electric shock, do not open covers. No user serviceable parts inside. Refer servicing to qualified service personnel.

This symbol is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Safety: Should any liquid or solid object fall into the camera, unplug the unit and have it checked by qualified personnel before operating it any further.

Installation: Do not install the unit in an extremely hot or humid place.

The unit is not designed to be waterproof. Exposure to rain or water may damage the unit.

Horizontal linearity controls located at the rear panel are for special adjustments by qualified personnel only

Cleaning: Clean the unit with a slightly damp soft cloth. Use a mild household detergent. Never use strong solvents such as thinner or benzene as they might damage the finish of the unit.

Retain the original carton and packing materials for safe transport of this unit in the future.

8. Important Safeguards:

1. Carefully read and follow instructions. 2. Do not use this apparatus near water. 3. Clean the unit with a slightly damp soft cloth. Use a mild household detergent. 4. Install in accordance with the manufacturer’s instructions. 5. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat. 6. If using a 60P5VDC power supply, make sure the power supply is securely attached to the

receptacle.

Doc # INS-20K1X2-F Issue Date: 03/17/2011

7. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

Revision: A Page 5 of 6

Doc # INS-20K1X2-F Issue Date: 03/17/2011 Revision: A Page 6 of 6

8. Only use attachments/accessories specified by the manufacturer. 9. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

10. CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce

the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

11. Do NOT use power source other than that specified. 12. Use only Class 2 power source or adapter provided by manufacturer.

9. Contact Information For technical assistance with this product, please contact the supplier from whom the product was purchased. For OEM inquiries, contact Videology Imaging Solutions: North / South America:

Europe:

Videology Imaging Solutions Inc. 37M Lark Industrial Parkway Greenville, RI 02828 USA Tel: (401) 949-5332 Fax: (401) 949-5276

Videology Imaging Solutions Europe Neutronenlaan 4 NL-5405 NH Uden, Netherlands Tel: +31 (0) 413 256 261 Fax: +31 (0) 413 251 712

Please visit our website at: http://www.videologyinc.com VIDEOLOGY IMAGING SOLUTIONS is an ISO 9001 registered video camera developer and manufacturer serving industrial, machine vision, biometric, security, and specialty OEM markets. Videology designs, develops, manufactures, and distributes video, image acquisition, and display technologies and products to OEMs worldwide.