installation instructi - cobalt av · 246559 - center dash shelf mount ford crown victoria police...

246559 - Center Dash Shelf Mount

Ford Crown Victoria Police Interceptor 1995-2012

Installation Instructions

ComtronICS CobaltAV | 2350 Fortune Drive, Lexington KY 40509USTF: 1.800.264.6021 | PH: 859.299.9494 | FAX: 859.299.9334Email: [email protected] | www.comtronicsnow.com

©2015 ComtronICS Cobalt AV. All rights reserved.

With ComtronICS’ new EZ Dash Mount, your tablet is securely mounted on the vehicle’s dash, adjusts for multiple viewing

positions, and frees up valuable space in your vehicle’s interior.

By ProClip USA

mailto:[email protected]

1. Remove the front panel that the trunk release button is located on.

2. Start at the right side and work your way left. Unplug the trunk release wires to completely remove the panel. Set the panel aside.

Ford Crown VictoriaPolice Interceptor 1995-2012


By ProClip USA

3. Remember to also remove the short panel on the left side of the steering wheel. Start with the far left side of the panel.

4. Once the lower panels have been removed, take out the eight screws that fasten the frame around the radio and instruments. Remember the two above the speedometer.



By ProClip USA

5. Pull out the instrument panel starting under the radio area. Detach the wires behind the radio. Remember to also tilt the steering wheel all the way down to remove the instrument panel.

6. Detach the wires from the light switches on the far left. Once the wires are detached, remove the switches from the panel by pressing forward on the switch panel.



By ProClip USA

7. Once the switch panel is removed from the instrument panel, plug the wires back into the switches. This will quiet the continuous beeping from the light switch sensor. 8. Completely remove the instrument frame from the vehicle.

9. Cover the opening in the carpet under the center console area. This will reduce the chances of losing nuts and bolts that might drop into the area.



By ProClip USA

10. The connecting block will attach to the slots on the steel dash frame behind this opening. (See arrows)

11. Push out the plastic clips holding on the wire harness and press the wire harness back or out of the way of the slots in the steel frame.



By ProClip USA

12. Insert the included “T” bolts with a square neck into the back of the right slot on the steel frame in the opening. (Tip: It will be easier to loosely attach only the right side of the block first. Also, it might be helpful to tape the “T” bolts in from the back side.)



By ProClip USA

13. When attaching the connecting block, the threaded hole for the connecting screw on the connecting block should be facing downward. Fasten onto the “T” bolt with the included nut and lock washer. (Tip: It will be easier to hold the connecting block when the screw is inserted into the threaded hole.)



By ProClip USA

14. A very helpful tool will be a “universal” attached to a driver or socket wrench. This tool will assist in fastening the nuts onto the “T” bolts in the connecting block.

15. Align the left hole up with the left slot in the steel dash frame.



By ProClip USA

16. Insert the included “T” bolts with a square neck into the back of the left slot on the steel frame in the opening. Fasten with the included nut and lock washer. (Tip: Again, it might be helpful to tape the “T” bolt in from the back side.)

17. Above, the connecting block attached. (Tip: keep the connecting block towards the right in the slots.)



By ProClip USA

18. To avoid any possible future rattles, file off about 1/8 inch around the opening where the pedestal mount will come out from the dash. (Tip: This can be done prior to attaching the connecting block.)

19. Under the center console area there are two holes in the steel dash frame.



By ProClip USA

20. Insert the pedestal mount upward through an opening inside of the dash in front of the two holes in the frame.

21. The top of the pedestal mount should come out above through the opening in the dash under the connecting block.



By ProClip USA

22. Using the included Allen wrench and screw, attach the upper part of the pedestal mount onto the connecting block. Do not fasten it tightly yet. Tighten the lower two nuts and bolts attaching the lower pedestal plate to the lower steel dash frame first. Then go back and tighten the connecting block screw.

23. These are the two holes in the steel dash frame under the center console area. Insert the two included hex bolts down through the holes from the top.



By ProClip USA

24. The holes in the plate at the bottom of the pedestal mount should go onto the hex bolts in the lower steel dash frame. Tightly fasten the pedestal plate to the steel dash frame with the included lock washers and nuts.

25. The pedestal base plate fastened to the steel dash frame.



By ProClip USA

26. Now go back and securely tighten the connecting block screw.

27. Take the set aside interior panel, with the trunk lid opener, and place a tape measure at the left side of the grooved notch in the vertical center of the panel.



By ProClip USA

28. From the left, measure 16 5/8 inches to the right and make a mark. The mark should be 1/8 inch above the grooved notch in the vertical center of the panel.

29. Using a 1¼ inch hole saw, cut a hole through the panel.



By ProClip USA

30. Reattach the instrument panel. Then reattach the panel with the trunk release button. Make sure to reattach all the wires that were removed from the lights and radio.

31. When attaching the upper tilt swivel mount, keep the mount straight up and down. If it is angled, it can create an undesirable angle when swiveling.



By ProClip USA

ComtronICS CobaltAV | 2350 Fortune Drive, Lexington KY 40509USTF: 1.800.264.6021 | PH: 859.299.9494 | FAX: 859.299.9334Email: [email protected] | www.comtronicsnow.com

©2015 ComtronICS Cobalt AV. All rights reserved.


By ProClip USA

Returns, Limited Warranty, and Liabilities

ReturnsNo products shipped hereunder may be returned without ComtronICS’ prior approval. In order to return a product, Buyer must obtain an RMA (Return Merchanidise Authorization) Number. All returns must be made within thirty (30) days of the invoice date and include proof of purchase. The product must be in undamaged and unused condition, meaning NO screw can be screwed into any product, not even the pre-drilled holes. NO holes may be punched through a product, NO scratches or screw marks upon the product, and NO velcro tape marks, etc. We reserve the right to withhold a refund if we deem the product is damaged. A copy of your original order or invoice must accompany return. ALL COMPONENTS PERTAINING TO THE ORINGINAL PART MUST BE RETURNED.

Limited Warranty and LiabilitiesComtronICS warrants that the Products will be free of defects in materials and workmanship for a period of one (1) year from the date of purchase. If any Product should become defective during the warranty period, ComtronICS, at its option, will replace it, repair it, or refund the purchase price. Repair or replacement parts or Products will be furnished on an exchange basis and will either be new or reconditioned. All replaced Products shall become the property of ComtronICS. Warranty service is available to you by delivering the Product during the warranty period to the company it was purchased from, or to ComtronICS at: 2350 Fortune Drive, Lexington KY 40509 USA, and providing proof of purchase, price, and date of purchase. If shipped to ComtronICS, the Buyer must first call Comtron-ICS at 1.800.264.6021, or email ComtronICS at [email protected] to obtain a returns approval and return number. Buyer will bear all shipping, packaging, and insurance costs, and all other costs, excluding labor and parts necessary to effectuate repair, replace-ment or refund under this warranty. For more information on how to obtain warranty service, write, email or call ComtronICS at: 2350 Fortune Drive, Lexington KY 40509, Tel. 1.800.264.6021, or Email: [email protected].

THIS LIMITED WARRANTY DOES NOT EXTEND TO ANY PRODUCT WHICH HAS BEEN DAMAGED AS A RESULT OF ACCIDENT, MISUSE, ABUSE, OR AS A RESULT OF UNAUTHORIZED SERVICE. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES FOR THIS PRODUCT. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABLITIY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRING-LMENT SHALL NOT HAVE A GREATER DURATION THAN 1 YEAR FROM THE DATE OF PURCHASE. IN THE EVENT THIS PRODUCT BECOMES DEFECTIVE DURING THE WARRANTY PERIOD, THE BUYER’S EXCLUSIVE REMEDY SHALL BE REPAIR, REPLACEMENT OR REFUND AS PROVIDED ABOVE.

IN NO EVENT SHALL COMTRONICS BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION LOSS OF PROPERTY, ARISING FROM BREACH OF ANY EXPRESSED OR IMPLIED WARRANTY.

COMTRONICS DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, OTHER THAN THOSE SET FORTH ABOVE.

IN NO EVENT WILL COMTRONICS BE LIABLE TO THE BUYER OR ANY THIRD PARTY FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, INDIRECT, SPECIAL, PUNITIVE, OR EXEMPLARY DAMAGES, INCLUDING ATTORNEY FEES ARISING OUT OF THE USE, OR THE INABILITY TO USE THE PRODUCTS, OR FOR ANY CLAIM BY ANY OTHER PARTY, EVEN IF COMTRONICS HAS BEEN ADVISED OF THE POSSIBIITY OF SUCH DAMAGES.

mailto:[email protected]

Slide Number 1Ford Crown Victoria Police �Interceptor 19951-2012�Installation InstructionsFord Crown Victoria Police �Interceptor 19951-2012�Installation InstructionsFord Crown Victoria Police �Interceptor 19951-2012�Installation InstructionsFord Crown Victoria Police �Interceptor 19951-2012�Installation InstructionsFord Crown Victoria Police �Interceptor 19951-2012�Installation InstructionsFord Crown Victoria Police �Interceptor 19951-2012�Installation InstructionsFord Crown Victoria Police �Interceptor 19951-2012�Installation InstructionsFord Crown Victoria Police �Interceptor 19951-2012�Installation InstructionsFord Crown Victoria Police �Interceptor 19951-2012�Installation InstructionsFord Crown Victoria Police �Interceptor 19951-2012�Installation InstructionsFord Crown Victoria Police �Interceptor 19951-2012�Installation InstructionsFord Crown Victoria Police �Interceptor 19951-2012�Installation InstructionsFord Crown Victoria Police �Interceptor 19951-2012�Installation InstructionsFord Crown Victoria Police �Interceptor 19951-2012�Installation InstructionsFord Crown Victoria Police �Interceptor 19951-2012�Installation InstructionsFord Crown Victoria Police �Interceptor 19951-2012�Installation InstructionsFord Crown Victoria Police �Interceptor 19951-2012�Installation Instructions

installation instructi - cobalt av · 246559 - center dash shelf mount ford crown victoria police...

Documents