installation guidelines - nova · pdf fileanoquick - loop & saucer 800.753.9688 www ......
TRANSCRIPT
Note: Use only withgraphics mountedon 3/16” foamboardor other similarthickness. Canalso use a foldededge thinner substrate.
Instructions for Hanging
Figure 2
Figure 3
Figure 5
Figure 4
Figure 1
Figure 6
End CapsAnoQuick Cable Clips Ball Chains
Installation GuidelinesAnoQuick - Ball Chains 800.753.9688 www.novadisplay.com
Step 1Prepare edges of graphic. Place the graphic on tabletop with one edge at the table edge.Using the AnoQuick holder, run it across thegraphic edge, crushing it slightly. Fig. 1
Step 2Starting at one corner, push the holder onto thegraphic. Work your way down the holder tappingit down firmly to seat the graphic fully. Fig. 2
Step 3Insert single ball of ball chain into inner channel ofCable Clip. The cable should snap into place. Fig. 3
Step 4Align one round end of cable clip with top channelof the aluminum rail and insert. Once in place,insert end of ball chain into channel. Then pressdown on the other round end of the cable clip andslide into rail by pushing on the clip. Fig. 4
Note: Be sure to slide the ball chain into place bypushing on the cable clip. Do not pull on,or push against, the ball chain as this willcause it to bind in the channel.
Step 5Push end caps into place. Fig. 5
Step 6Suspend poster. Fig. 6
Installation GuidelinesAnoQuick - Loop & Saucer 800.753.9688 www.novadisplay.com
Figure 2
Figure 3
Figure 5
Figure 4
Figure 1
Figure 6
End CapAnoQuick Cable Clips Loop & Saucer
Note: Use only withgraphics mountedon 3/16” foamboardor other similarthickness. Canalso use a foldededge thinner substrate.
Instructions for Hanging
Step 1Prepare edges of graphic. Place the graphic on tabletop with one edge at the table edge.Using the AnoQuick holder, run it across thegraphic edge, crushing it slightly. Fig. 1
Step 2Starting at one corner, push the holder onto thegraphic. Work your way down the holder tappingit down firmly to seat the graphic fully. Fig. 2
Step 3Insert single ball of ball chain into inner channel ofCable Clip. The cable should snap into place. Fig. 3
Step 4Align one round end of cable clip with top channelof the aluminum rail and insert. Once in place,insert end of ball chain into channel. Then pressdown on the other round end of the cable clip andslide into rail by pushing on the clip. Fig. 4
Step 5Push end caps into place. Fig. 5
Step 6Suspend poster. Fig. 6
Figure 3
Figure 5
Figure 4
Figure 2Figure 1
Figure 6
Installation GuidelinesAnoQuick - Loop & Saucer 800.753.9688 www.novadisplay.com
Cable & SaucerEnd CapAnoQuick Cable Clips
Note: Use only withgraphics mountedon 3/16” foamboardor other similarthickness. Canalso use a foldededge thinner substrate.
Instructions for Hanging
Step 1Prepare edges of graphic. Place the graphic on tabletop with one edge at the table edge.Using the AnoQuick holder, run it across thegraphic edge, crushing it slightly. Fig. 1
Step 2Starting at one corner, push the holder onto thegraphic. Work your way down the holder tappingit down firmly to seat the graphic fully. Fig. 2
Step 3Insert single ball of ball chain into inner channel ofCable Clip. The cable should snap into place. Fig. 3
Step 4Align one round end of cable clip with top channelof the aluminum rail and insert. Once in place,insert end of ball chain into channel. Then pressdown on the other round end of the cable clip andslide into rail by pushing on the clip. Fig. 4
Step 5Push end caps into place. Fig. 5
Step 6Suspend poster. Fig. 6
Installation GuidelinesAnoQuick - Slatwall Hangers 800.753.9688 www.novadisplay.com
Step 3Push end caps into place. Fig. 3
Step 4Insert hangers into upper portion of slatwall.Hangers will rest on lower portion of slatwall. Fig. 4
Step 5Place the AnoQuick on the hangers using the bottomchannel of the top rail.
Figure 4
End Caps
Figure 3
AnoQuick Round or Square Slatwall Hangers
Figure 2Figure 1
Instructions for Hanging
Step 1Prepare edges of graphic. Place the graphic on tabletop with one edge at the table edge.Using the AnoQuick holder, run it across thegraphic edge, crushing it slightly. Fig. 1
Step 2Starting at one corner, push the holder onto thegraphic. Work your way down the holder tappingit down firmly to seat the graphic fully. Fig. 2
Note: Use only withgraphics mountedon 3/16” foamboardor other similarthickness. Canalso use a foldededge thinner substrate.
Note: To ensure that the frame hangs level use twohangers placed an equal distance in fromeach side of the frame.
Installation GuidelinesAnoQuick - MultiClips 800.753.9688 www.novadisplay.com
Step 1Insert dowel into sown pocket at top and bottom ofgraphic. Fig. 1
Step 2Insert dowel (with fabric) into the AnoQuick holder.Fig. 2
Instructions for Hanging
Figure 2 Figure 3
Figure 6
Figure 4
Figure 1
Figure 7
End CapsAnoQuick Round or Square MultiClips
Figure 5
Step 3Squeeze sides of MultiClip together. Fig.3
Step 4Align the bottom rail of the MultiClip with thetop channel of the aluminum holder. SlideMultiClip into rail. Fig. 4Repeat steps 3 & 4 for second MultiClip.
Step 5Push end caps into place. Fig. 5 & 6
Step 6Suspend poster. Fig. 7
Installation GuidelinesAnoQuick - MultiClips 800.753.9688 www.novadisplay.com
Note: Use only withgraphics mountedon 3/16” foamboardor other similarthickness. Canalso use a foldededge thinner substrate.
Figure 3
Figure 5
Figure 4
Figure 6
End CapsAnoQuick Round or Square MultiClips
Instructions for Hanging
Step 1Prepare edges of graphic. Place the graphic on tabletop with one edge at the table edge.Using the AnoQuick holder, run it across thegraphic edge, crushing it slightly. Fig. 1
Step 2Starting at one corner, push the holder onto thegraphic. Work your way down the holder tappingit down firmly to seat the graphic fully. Fig. 2
Step 3Squeeze sides of MultiClip together. Fig.3
Step 4Align the bottom rail of the MultiClip with thetop channel of the aluminum holder. SlideMultiClip into rail. Fig. 4Repeat steps 3 & 4 for second MultiClip.
Step 5Push end caps into place. Fig. 5 & 6
Step 6Suspend poster. Fig. 7
Figure 2Figure 1
Installation GuidelinesAnoQuick - MultiClips w/ Pegs 800.753.9688 www.novadisplay.com
Instructions for Hanging
Step 1Have your printer punch three holes, evenlyspaced, along the top and bottom edges of yourgraphic. Fig. 1
Step 2Push both parts of the peg together througheach of the punched holes. Fig. 2
Step 3Slide AnoQuick onto substrate. The pegs shouldslide into the side rails. Fig. 3
Step 4Squeeze sides of MultiClip together. Fig. 4Align the bottom rail of the MultiClip with thetop channel of the holder.Slide MultiClip into rail. Fig. 5Repeat step 3 for second MultiClip.
End Caps
Figure 7Figure 6
Figure 3Figure 2Figure 1
Multiclips
Figure 4
Pegs
Figure 5
AnoQuick
Note: Make sure holes are evenly spaced.
Note: This is the easiest way to safely hangheavier substrates.
Step 5Push end caps into place. Fig. 6
Step 6Suspend poster. Fig. 7
Installation GuidelinesAnoQuick - MultiClips w/ Pegs 800.753.9688 www.novadisplay.com
Instructions for Hanging
Step 1When using AnoQuick to hang 1/8” Sintra or anequally heavy substrate, have your printer punchtwo 1/4” holes along the top and bottom edgesof print — or only the top if no bottom holder isbeing used. Fig. 1
Step 2Push both parts of the peg together through eachof the punched holes. Fig. 2
Step 3Slide AnoQuick onto substrate. The pegs shouldslide into the side rails. Fig. 3
Pegs
Figure 1
AnoQuick
Figure 2
Figure 3
Note: This is the easiest way to safely hangheavier substrates.
Note: Each hole must be centered 1/4” in fromthe edge of the substrate.
Installation GuidelinesAnoQuick - Wall Mount Hangers 800.753.9688 www.novadisplay.com
Step 3Push end caps into place. Fig. 3
Step 4Install wall mounting hangers using eithernails or screw. Hammer nails into wall oruse a Phillips head screwdriver for screws. Fig. 4
Step 5Suspend poster.
Figure 4
End Caps Wall Mount Hangers Wood Screws orMolly Anchors
Figure 3
AnoQuick Round or Square
Note: Use only withgraphics mountedon 3/16” foamboardor other similarthickness. Canalso use a foldededge thinner substrate.
Figure 2Figure 1
Instructions for Hanging
Step 1Prepare edges of graphic. Place the graphic on tabletop with one edge at the table edge.Using the AnoQuick holder, run it across thegraphic edge, crushing it slightly. Fig. 1
Step 2Starting at one corner, push the holder onto thegraphic. Work your way down the holder tappingit down firmly to seat the graphic fully. Fig. 2
Note: The use of Molly Anchors are recommendedfor drywall installations (predrilling 3/16”holes is necessary).
Installation GuidelinesAnoQuick - Wall Mount Hangers 800.753.9688 www.novadisplay.com
Figure 2Figure 1
End CapsAnoQuick
Figure 3
Figure 5Figure 4
Window Mounts
Note: Use only withgraphics mountedon 3/16” foamboardor other similarthickness. Canalso use a foldededge thinner substrate.
Instructions for Hanging
Step 1Prepare edges of graphic. Place the graphic on tabletop with one edge at the table edge.Using the AnoQuick holder, run it across thegraphic edge, crushing it slightly. Fig. 1
Step 2Starting at one corner, push the holder onto thegraphic. Work your way down the holder tappingit down firmly to seat the graphic fully. Fig. 2
Step 3Slide the Window Suction Cups into the top railof the AnoMulti Holder. Fig. 3 & 4
Step 4Push end caps into place. Fig. 5
Step 5Suspend poster. Make sure glass and suction cupsare clean and free of dust and dirt.
Important note:For best performance when first applied andoccasionally thereafter, press the middle of the cup(on the cap) to “burp” extra air out