installation guide sesam 2017 releasehome.hib.no/ansatte/tct/ftp/h2017 marinteknisk analyse... ·...
TRANSCRIPT
Date: May /2017
Prepared by DNV GL - Software
© DNV GL AS. All rights reserved
This publication or parts thereof may not be reproduced or transmitted in any form or by any means, including copying or recording, without the prior written consent of DNV GL AS
Installation Guide | Sesam | www.dnvgl.com/software Page i
Table of contents
1 IMPORTANT INFORMATION .............................................................................................. 1
2 BEFORE INSTALLING ....................................................................................................... 1
3 HOW TO INSTALL ........................................................................................................... 2
3.1 Selecting packages/applications to install 4
4 SILENT INSTALLATION .................................................................................................... 7
4.1 Install applications silently using Software Installer 7
5 UNINSTALLATION ........................................................................................................... 9
6 REDISTRIBUTABLES ...................................................................................................... 10
7 AFTER INSTALLATION ................................................................................................... 11
8 LICENSE MANAGER ....................................................................................................... 11
9 TROUBLESHOOTING ..................................................................................................... 13
10 HOW TO FIND MORE INFORMATION ................................................................................ 13
| Installation Guide | Sesam | www.dnvgl.com/software Page 1
1 IMPORTANT INFORMATION
Please study this Installation Guide prior to installing Sesam software.
If you run into problems that you do not find a solution for in the installation guide,
please send an e-mail to: [email protected] or contact your local support.
Tel. European time zone Tel. American time zone
Tel. Asian time zone
+47 6757 8181 +1-800-800-7764
+86 21 3279 9000
| Installation Guide | Sesam | www.dnvgl.com/software Page 1
2 BEFORE INSTALLING
Please be aware of the following before you start the Sesam 2017 installation:
Supported platforms:
o Windows 7 64-bit
o Windows 8.1 64-bit
o Windows 10 (except Pipeline Tools, see below)
At least 2 GB free disk space is required for a full installation.
Perform the installation from a user with administrator privileges.
Have a license file available for Sesam (or the address of the network license service – the
License Service running on a different computer) when installing on a new computer.
On Windows 7: .NET 4.0 or higher must be installed prior to Sesam installation. If not installed,
setup will not start and you will see a message like
To install .NET Framework 4.5, run the setup program found in subfolder Redists on the
installation medium:
Redists\Microsoft .net\4.5\Full\NDP452-KB2901907-x86-x64-AllOS-ENU.exe
Microsoft Word is a prerequisite for installing ReportBuilder with Xtract.
Pipeline Tools
o Microsoft Excel is a prerequisite
Version must be MS Office 2010 32-bit version
no support for MS Office 365/2016 nor any 64-bit version of MS Office
o Not supported on
Windows 10
| Installation Guide | Sesam | www.dnvgl.com/software Page 2
3 HOW TO INSTALL
A list of the current Sesam programs can be found in Section 8 of “Sesam 2017 Release
Documentation.pdf”.
Open the distribution folder and double-click ‘Setup.exe’ to launch ‘DNV GL - Software Installer’.
Remember that you will need administrative privileges on your computer to install the Sesam
applications.
Click the checkbox to accept the terms in the license agreement:
If one or more Sesam applications are installed on your computer, the ‘Maintenance dialog’ will open.
Check ‘Configure Destination folders and License Manager’ if you want to change the default installation
paths or install/configure License Manager.
| Installation Guide | Sesam | www.dnvgl.com/software Page 3
If it is the first Sesam installation on your computer, the ‘Destination folders’ dialog will open by default.
Uncheck ‘Use default folders’ to change the destination folders:
These settings will be remembered for future setups on the same computer with the same user, and will
also be used for silent installation.
If License Manager is not yet installed, you should install it now. Click Next to start. See chapter License
Manager for further details.
| Installation Guide | Sesam | www.dnvgl.com/software Page 4
3.1 Selecting packages/applications to install
By default, all available applications on the distribution medium will be selected for installation unless
you have already installed a newer version of an application.
To change the default selection, check/uncheck the ones you want to install/not install.
There are several icons used in the checkboxes showing the selection/installation status. Click ‘Icons
descriptions’ for explanation.
The Description pane gives additional information about the application or package selected, which
version is already installed and the version available on the installation medium. Click ‘Next’ when you
have finished selecting the applications to install.
| Installation Guide | Sesam | www.dnvgl.com/software Page 5
The selected applications are listed. Click ‘Start’ to start the installation. A dialog box with a progress bar
will appear for each application, one at a time.
When all selected applications have been installed, click ‘Finish’ to exit the installer.
During installation, you may click ‘Stop’ to stop the current ongoing installation. Software Installer will
stop after the current installation is finished (like Fatfree in the screen dump below).
| Installation Guide | Sesam | www.dnvgl.com/software Page 6
If there are remaining applications to be installed, it is possible to resume installation.
Press Continue to resume installation of the remaining application, or Cancel to quit setup.
| Installation Guide | Sesam | www.dnvgl.com/software Page 7
4 SILENT INSTALLATION
4.1 Install applications silently using Software Installer
Open a command prompt, go to the installation folder, and type
setup.exe /?
in order to see a list of available command line options.
If you need the exit code from the setup, you should prefix the command with start/wait as shown in
the example below.
To update the applications that are already installed on a computer only, type:
start /wait setup UPDATE_ONLY_INSTALLED_APPLICATIONS
NOTE: UPDATE_ONLY_INSTALLED_APPLICATIONS cannot be combined with any INSTALL_APPLICATION… arguments.
Tip:
Press Ctrl+C to copy
the text in this window to the clipboard. Use parts of the pasted text to e.g. uninstall all programs.
| Installation Guide | Sesam | www.dnvgl.com/software Page 8
Output will be written to standard output, i.e. to the command window from where the job started.
Example output from the command:
start /wait setup UPDATE_ONLY_INSTALLED_APPLICATIONS
Running: DNV GL - Software Installer, version: 3.6.2.21
Searched for DNV GL - Software applications in subfolders of:
<mysetupfolder>
Argument: UPDATE_ONLY_INSTALLED_APPLICATIONS
Install status for installed applications:
Application Version Manager V3.1-01 (Installed)
Framework V3.12-00 (New version, checked for installation)
GeniE 64 V7.1-12 (New version, checked for installation)
.NET Framework 3.5 - 3.5.21022.8 (A newer version is installed)
Microsoft .NET Framework 4 KB2468871-v2 (x64) (Installed)
Microsoft .NET Framework 4 - 4.0.30319.1 (A newer version is installed)
Microsoft .NET Framework 4.5.2 - 4.5.51209.34209 ( 379893) (Installed)
Microsoft ReportViewer 2010 Redistributable - 10.0.30319.1 (Installed)
Microsoft software update KB2600211 (Installed)
Microsoft Visual C++ 2008 Redistributable - 9.0.30729.17 (Installed)
Microsoft Visual C++ 2010 x64 Redistributable - 10.0.40219.1 (Installed)
Microsoft Visual C++ 2010 x86 Redistributable - 10.0.40219.1 (Installed)
Updating configuration:
Installing: Framework V3.12-00
Installing: GeniE 64 V7.1-12
Summary: Successfully installed 2 applications
| Installation Guide | Sesam | www.dnvgl.com/software Page 9
5 UNINSTALLATION
You may uninstall a set of Sesam applications using Software Installer.
Select the applications you would like to uninstall.
| Installation Guide | Sesam | www.dnvgl.com/software Page 10
6 REDISTRIBUTABLES
Software Installer will install the redistributable packages which are required to run Sesam
automatically, except for .NET framework 4, which must be installed prior to running Software Installer.
If required, .NET framework 3.5 must also be installed manually, see notes below.
The following software is included in the Redists folder, and will be installed automatically if required by
the selected Sesam package(s):
VC 2015 Redist\vc_redist.x86.exe : Visual C++ 2015 redistributable for 32-bit applications
VC 2015 Redist\vc_redist.x64.exe : Visual C++ 2015 redistributable for 64-bit applications
VC2010\vcredist_x86.exe : Visual C++ 2010 redistributable for 32-bit applications
VC2010\vcredist_x64.exe : Visual C++ 2010 redistributable for 64-bit applications
VC2008\vcredist_x86.exe : Visual C++ 2008 redistributable for 32-bit applications
VC2005\vcredist_x64.exe : Visual C++ 2005 redistributable for 64-bit applications
DirectX9c-June2010\DXSETUP.exe : DirectX9 (used by GeniE, DeepC and Sima)
…\NDP40-KB2468871-v2-x86.exe : .Net 4.0 cumulative update, before 4.03
…\NDP40-KB2468871-v2-x64.exe : .Net 4.0 cumulative update, before 4.03
…\NDP40-KB2600211-x86-x64.exe : .Net 4.0 cumulative update 4.03
ReportViewer.exe : includes controls for viewing reports
The following software is included in the Redists folder, and will not be installed automatically:
dotNetFx40_Full_x86_x64.exe : .NET framework 4
dotnetfx35.exe : .NET framework 3.5
rootsupd.exe : Update for root certificates for Windows
Note:
dotnetfx35.exe is required in some configurations to run HydroMesh and Digin, and is therefore
only available in the Redists folders for SesamPackage, HydroDPackage and DeepCPackage.
An error like the one below probably means that the root certificates on your computer must be
updated. Run rootsupd.exe to update the root certicicates.
| Installation Guide | Sesam | www.dnvgl.com/software Page 11
7 AFTER INSTALLATION
After installing the software, log on with the user that will run the Sesam programs and start ‘Application
Version Manager’ for an initial configuration.
8 LICENSE MANAGER
Check Configure Destination folders and ‘License Manager’ to install/configure License Manager:
Press Next in the ‘Destination folders’ dialog to get to the License configuration screen:
| Installation Guide | Sesam | www.dnvgl.com/software Page 12
Press ‘Install and Configure’ to install License Manager:
License Manager setup is described in a separate installation guide.
When finished, go back to ‘DNV GL - Software Installer’ and click ‘Next’ to continue the Sesam
installation.
| Installation Guide | Sesam | www.dnvgl.com/software Page 13
9 TROUBLESHOOTING
The following redistributables should be installed automatically when starting the installation
program:
o Visual C++ redistributables
o DirectX9 (used by GeniE and Sima)
If the installation program fails to install these, they can be installed manually from the subfolder
Redists.
Xtract installation is not possible to install if Microsoft Word is not present on your computer.
Pipeline tools is not possible to install if Microsoft Excel is not present on your computer.
10 HOW TO FIND MORE INFORMATION
Status lists, release notes and user documentation for the different applications can be found on the
Customer Portal. Go to http://www.dnvgl.com/software/ and click Support. Her you will find the
Customer login portal for Sesam.
ABOUT DNV GL Driven by our purpose of safeguarding life, property and the environment, DNV GL enables organizations to advance the safety and sustainability of their business. We provide classification and technical assurance along with software and independent expert advisory services to the maritime, oil and gas, and energy industries. We also provide certification services to customers across a wide range of industries. Operating in more than 100 countries, our 16,000 professionals are dedicated to helping our customers make the world safer, smarter and greener.
SOFTWARE
DNV GL is the world-leading provider of software for a safer, smarter and greener future in the energy,
process and maritime industries. Our solutions support a variety of business critical activities including design and engineering, risk assessment, asset integrity and optimization, QHSE, and ship management. Our worldwide presence facilitates a strong customer focus and efficient sharing of industry best practice and standards.