installation guide - strobesnmore.com · e3 flash patterns p1: burst flash p2: burst flash...

of 1/1
1 FEATURES Voltage: DC 12/24V Current E3: .35 AMPS/MAX, 25 AMPS/AVG @ 12.8VDC Current E4 and E6: Current: .8AMPS/MAX, .5AMPS/AVG @ 12.8VDC Housing: ABS Material (black) Cover: PC Material (clear) Flash Patterns: 12, includes OFF Heat Sink: Extruded Aluminum Switching Function: Previous/Next/Simultaneous Waterproof Design WARRANTY Provided this product is installed and operated in a manner consistent with its use, Strobes N’ More guarantees the E-Series of lights for a period of 5 years from the day of purchase. Units demonstrated to be defective within the warranty period will be repaired or replaced at the seller’s discretion. The end user is responsible for shipping / returning the item to Strobes N’ More and we will cover the cost of return shipping. International customers are responsible for all shipping charges. Improper installation or use of inappropriate or inadequate wiring or circuit protection causes the warranty to be void. Applying voltage directly to the LED’s will cause immediate failure and void the warranty. Damages resulting from improper use and/or accidents are not covered by this warranty. Aluminum will corrode if left in the elements or area of high road salt use. Proper cleaning of the light is essential to keeping the unit in like new condition. Magnets are used to hold the light in place Use of non-compatible components and assemblies may cause damage to the system and/or personal injury, and voids all warranties. Strobes N’ More LLC shall in no way be liable for other damages including consequential, indirect or special damages whether loss is due to negligence or breach of warranty. Visit www.StrobesNMore.com/warranty for more information. RED - Activation Wire + 12 Volts • BLACK - Ground Wire - 12 Volts • BLUE - Flash Pattern Selection YELLOW - Synchronize Wire • WHITE - Hi/Low Power Wire * E6 Brake Model: WHITE - Brake Override Connect YELLOW wires of all heads together to sync Connect two YELLOW wire groups together: Group 1: Phase 1 & Phase 1 or Phase 2 & Phase 2 will flash together Group 2: Phase 1 & Phase 1 or Phase 2 & Phase 2 will flash alternative FLASH PATTERN SELECTION Apply +12 Volts to BLUE wire to change patters: • 1 SEC for Next Pattern • 1~3 SECS for Previous Pattern • 3~5 SECS for Steady Burn • 5+ SECS light will turn off • Reapply +12 Volts to BLUE wire and light will reappear E3 FLASH PATTERNS P1: Burst Flash P2: Burst Flash Alternating P3: Quad Flash P4: Quad Flash Alternating P5: Double Flash P6: Double Flash Alternating P7: Single Flash P8: Single Flash Alternating P9: Mixed Flash P10: Mixed Flash Alternating P11: Steady P12: OFF E4 and E6 FLASH PATTERNS P1: Alternating Quad Burst P2: Simultaneous Quad Burst P3: Simultaneous Quad Burst P4: Quad Alternating P5: Quad Simultaneous P6: Quad Simultaneous P7: Single Alternating P8: Single Simultaneous P9: Single Simultaneous P10: Single Alternating Rapid P11: Single Simultaneous Rapid P12: Single Simultaneous Rapid P13: Alt Quad Single Rapid & Quad Burst P14: Alt Quad Single Rapid & Quad Burst P15: Alt Rapid Pulse w/ Variable Rate P16: Simultaneous Rapid Pulse w/ Variable Rate E4 and E6 FLASH PATTERNS continued... P17: Quad Burst & Quad Single Rapid & Quad Burst P18: Steady w/ 5 Single & Single POP P19: Steady 5 Single P20: Steady P21: Cycle Flash P22: OFF FULL DUAL COLOR PATTERNS: Quad Burst Dual Quad Flash Dual Single Flash Dual Siingle Rapid Flash Dual Quad Burst - Single Flash Alt Dual SIngle Flash (variable rate) Dual Quad - Single Burst Dual Cycle Flash Dual OFF Safety First! Before beginning the installation and/or operation of your LED’s, the installation technician and operator must read this manual in full, before installation to prevent severe injury or damage. NEVER apply any voltage to the LED directly. Failure to power the LEDs with the supplied factory installed flasher automatically voids the warranty. Installation GUIDE Strobes N' More E-Series LED’s

Post on 21-Jul-2020

3 views

Category:

Documents

0 download

Embed Size (px)

TRANSCRIPT

  • 1

    FEATURESVoltage: DC 12/24VCurrent E3: .35 AMPS/MAX, 25 AMPS/AVG @ 12.8VDCCurrent E4 and E6: Current: .8AMPS/MAX, .5AMPS/AVG @ 12.8VDCHousing: ABS Material (black)Cover: PC Material (clear)Flash Patterns: 12, includes OFFHeat Sink: Extruded AluminumSwitching Function: Previous/Next/SimultaneousWaterproof Design

    WARRANTY Provided this product is installed and operated in a manner consistent with its use, Strobes N’ More guarantees the E-Series of lights for a period of 5 years from the day of purchase. Units demonstrated to be defective within the warranty period will be repaired or replaced at the seller’s discretion. The end user is responsible for shipping / returning the item to Strobes N’ More and we will cover the cost of return shipping. International customers are responsible for all shipping charges. Improper installation or use of inappropriate or inadequate wiring or circuit protection causes the warranty to be void. Applying voltage

    directly to the LED’s will cause immediate failure and void the warranty. Damages resulting from improper use and/or accidents are not covered by this warranty. Aluminum will corrode if left in the elements or area of high road salt use. Proper cleaning of the light is essential to keeping the unit in like new condition. Magnets are used to hold the light in place Use of non-compatible components and assemblies may cause damage to the system and/or personal injury, and voids all warranties. Strobes N’ More LLC shall in no way be liable for other damages including consequential, indirect or special damages whether

    loss is due to negligence or breach of warranty. Visit www.StrobesNMore.com/warranty for more information.

    RED - Activation Wire + 12 Volts • BLACK - Ground Wire - 12 Volts • BLUE - Flash Pattern Selection YELLOW - Synchronize Wire • WHITE - Hi/Low Power Wire * E6 Brake Model: WHITE - Brake Override

    Connect YELLOW wires of all heads together to syncConnect two YELLOW wire groups together:Group 1: Phase 1 & Phase 1 or Phase 2 & Phase 2 will flash togetherGroup 2: Phase 1 & Phase 1 or Phase 2 & Phase 2 will flash alternative

    FLASH PATTERN SELECTIONApply +12 Volts to BLUE wire to change patters:• 1 SEC for Next Pattern• 1~3 SECS for Previous Pattern• 3~5 SECS for Steady Burn• 5+ SECS light will turn off• Reapply +12 Volts to BLUE wire and light will reappear

    E3 FLASH PATTERNSP1: Burst FlashP2: Burst Flash AlternatingP3: Quad FlashP4: Quad Flash AlternatingP5: Double FlashP6: Double Flash AlternatingP7: Single FlashP8: Single Flash AlternatingP9: Mixed FlashP10: Mixed Flash AlternatingP11: SteadyP12: OFF

    E4 and E6 FLASH PATTERNSP1: Alternating Quad Burst P2: Simultaneous Quad BurstP3: Simultaneous Quad BurstP4: Quad AlternatingP5: Quad SimultaneousP6: Quad SimultaneousP7: Single AlternatingP8: Single SimultaneousP9: Single SimultaneousP10: Single Alternating RapidP11: Single Simultaneous RapidP12: Single Simultaneous RapidP13: Alt Quad Single Rapid & Quad BurstP14: Alt Quad Single Rapid & Quad BurstP15: Alt Rapid Pulse w/ Variable RateP16: Simultaneous Rapid Pulse w/ Variable Rate

    E4 and E6 FLASH PATTERNS continued...P17: Quad Burst & Quad Single Rapid & Quad BurstP18: Steady w/ 5 Single & Single POPP19: Steady 5 SingleP20: SteadyP21: Cycle FlashP22: OFF

    FULL DUAL COLOR PATTERNS:Quad Burst DualQuad Flash DualSingle Flash DualSiingle Rapid Flash DualQuad Burst - Single Flash Alt DualSIngle Flash (variable rate) DualQuad - Single Burst DualCycle Flash DualOFF

    Safety First! Before beginning the installation and/or operation of your LED’s, the installation technician and operator must read this manual in full, before installation to prevent severe injury or damage. NEVER apply any voltage to the LED directly. Failure to power the LEDs with the supplied factory installed flasher automatically voids the warranty.

    Installation GUIDEStrobes N' More E-Series LED’s