installation gl1800/d/da instructions p/n...

Honda Dealer: Please give a copy of these instructions to your customer.

INSTALLATIONINSTRUCTIONS

Accessory Application

© 2018 American Honda Motor Co., Inc. - All Rights Reserved.

PARTS LIST

87951-MKC-A1021 of 17

Publication No.

MII 16426

Issue Date

January 2018

POWER AMPLIFIER &SPEAKER KIT

P/N 08A83-MKC-A00

GL1800/D/DA GL1800B/BD (go to page 18)

No. Description Qty

(1) Amplifier unit 1

(2) Stay A 1

(3) Stay B 1

(4) Sub harness 1

(5) Grommet 3

(6) Cover 1

(7) 5 mm screw (long) 4

(8) 5 mm screw (short) 2

(9) Collar 9

(10) 5 mm nut 5

(11) 4 mm screw 9

(12) Hole plug 1

(13) Well nut 1

(14) Speaker 4

(15) Sponge seal rubber 1

(16) Installation Instructions URL 1

Item N·m kgf·m Ibf·ft

4 mm screw 1 0.1 0.7

5 mm screw 4.2 0.4 3.1

5 mm nut 5.2 0.5 3.8

TORQUE CHARTTighten all screws, bolts, and nuts to their specified torque values. Refer to the Service Manual for the torque values of the removed parts.

TOOLS AND SUPPLIES REQUIREDBox-end wrench (8 mm)

Open-end wrench (8 mm)

Phillips screwdriver

Electric drill

Drill bit (6 mm)

Hole saw (30 mm)

Dish soap solution (Water:Dish soap - 100:1)

Isopropyl alcohol

Scissors

Shop towel

Torque wrench

(14)

(15)

(4)

(5)

(16)

(1)

(6)

(2)(3)

(7)

(12)

(13)

(11)

(10)

(9)

(8)

2 of 17

LEFT SADDLEBAG LID

LEFT SADDLEBAG GUARD COVER

LEFT MUFFLER

LEFT MUFFLERBOLTLoosen.

CLIP

BOLT

WASHER

SCREW

SCREW

INSTALLATION CAUTION

• To prevent burns, allow the engine, exhaust system,radiator, etc., to cool before installing the accessory.

NOTE:

• Heat the bonding surfaces with a hair dryer if theambient air temperature is below 70°F (21°C).

• The adhesive reaches full strength in 72 hours. Waitat least 24 hours before riding your motorcycle.

• Disconnect the negative (-) cable from the batterybefore installing this accessory.

• The clock memory wil l be erased when youdisconnect the battery. Reset the clock afterreconnecting the battery.

• Reinstall the removed parts on the motorcycle andmake sure that the wires and harnesses are notpinched.

1. Remove the left saddlebag guard cover as shown.<Left side>

2. Remove the parts as shown.

3. Loosen the bolt, then remove the left muffler as shown.

4. Open the left saddlebag lid as shown.

• Repeat on the right side.<Left side>

3 of 17

5. Remove the lef t s ide cover as shown, and disconnect the battery negative (-) cable.

LEFT SIDE COVER

6. Remove the right side cover in the same manner as the left side.

7. Remove the seat as shown.

SEATDisconnect the connector.

BOLT

WASHER

9. Fold the left rear view mirror backward as shown.

<Left side>

LEFT REAR VIEW MIRROR

10. Remove the left mirror arm panel as shown.

<Left side>

LEFT MIRROR ARM PANEL

SCREW

8. Remove the right and left passenger grip as shown.

WASHER

BOLT

RIGHT PASSENGER GRIP

CABLE

LEFT PASSENGER GRIPRemove the cable.

4 of 17

15. Remove the clip as shown.

16. Remove the left inner cowl as shown.12. Remove the right mirror arm panel and right rear view mirror in the same manner as the left side.

13. Remove the screw as shown.

• Repeat on the right side.

14. Remove the left deflector panel as shown.

<Left side>

SCREW

SCREW

LEFT INNER COWL

CLIP

CLIP

SCREW

<Left side>

SCREW

LEFT DEFLECTOR PANEL

CLIP

<Left side>


CLIP

11. Remove the left rear view mirror as shown.

BOLT

LEFT REAR VIEW MIRRORDisconnect the connector.

5 of 17

18. Remove the left middle cowl as shown.

<Left side>

LEFT MIDDLE COWL

22. Remove the clip and disconnect the 2P black connector as shown.

21. Remove the 2P black connector as shown.

<Right side>2-PIN WATERPROOF CONNECTOR (Black)

CLIP

2-PIN WATERPROOF CONNECTOR (Black)

19. Remove the right deflector panel, right inner cowl and right middle cowl in the same manner as the left side.



<Left side>

SCREW

SCREWCOLLAR

23. Remove the right outer air guide as shown.

SCREW

CLIPRIGHT OUTER AIR GUIDE

SCREW

6 of 17

24. Remove the pocket cable as shown.

POCKET CABLE

27. Remove the left front speaker grill as shown.


LEFT FRONT SPEAKER GRILL

SCREW

CLIPCLIP

<Left side>

SCREWMETER

28. Remove the screws as shown.


26. Remove the shelter as shown.

SCREW

CLIP

CLIP

SHELTER

7 of 17

29. Remove the speaker as shown.

SPEAKER (Save)

30. Remove the right side speaker in the same manner as the left side.

31. Open the rear trunk lid as shown.

• Refer to the Owner’s Manual and open the rear trunk lid using the emergency trunk cable.

REAR TRUNK LID

32. Remove the USB cord as shown.

• Perform this step on GL1800DA only.

USB CORD


<GL1800DA>

TRUNK HOLDER

SCREW

34. Remove the trunk front lower panel as shown.


• Repeat on the left side.

TRUNK FRONT LOWER PANEL

SCREW

SCREW

CLIP

CLIP

8 of 17

41. Disconnect the connector and remove the trunk center lower cover as shown.

36. Remove the trunk right side cover as shown.

• Repeat on the left side.<Right side>

TRUNK RIGHT SIDE COVER

SCREW


SPEAKER (Save)


39. Remove the left side speaker in the same manner as the right side.

40. Remove the clips as shown.


CLIP

<Left side>

SCREW

TRUNK CENTER LOWER COVER


9 of 17

44. Remove the rear fender as shown.

SCREW

REAR FENDERDisconnect the connector.


GROMMET (Save)

GROMMET (Save)

SCREW

<Left side>

42. Remove the grommets as shown. 45. Remove the saddlebag rear center cowl as shown.

46. Remove the left saddlebag upper cover as shown.

SCREW

SCREW

LEFT SADDLEBAG UPPER COVERDisconnect the connector.

SCREW

SADDLEBAG REAR CENTER COWL

10 of 17

47. Remove the left saddlebag rear cover as shown.

SCREW

LEFT SADDLEBAG REAR COVER

CLIPSCREW

48. Drill a 30 mm hole at each marked line of the left saddlebag as shown.

• Drill holes at the center of the marked lines.• Remove the any burrs from the edge of the

hole.

49. Drill a 6 mm hole at the marked points of the left saddlebag as shown.

• Remove the any burrs from the edge of the hole.

<Under side>

MARKED LINE

MARKED POINT

ELECTRIC DRILL (30 mm HOLE SAW)

LEFT SADDLEBAG

LEFT SADDLEBAG

ELECTRIC DRILL (6 mm BIT)

GROMMET

50. Apply dish soap solution to the position shown.

• Perform this step for all three grommets.

DISH SOAP SOLUTIONApply.

11 of 17

Align the end of grommet with the marked line as shown.

51. Install the grommets as shown.GROMMET

GROMMETMARKED LINE

52. Install the hole plug into stay-A as shown.

HOLE PLUG

STAY A

53. Install stay-B to the amplifier unit with the screws andcollars as shown.

54. Install stay-A to the amplifier unit with the screws andcollars as shown.

AMPLIFIER UNIT

AMPLIFIER UNIT

4 mm SCREW

4 mm SCREW

COLLAR

COLLAR

STAY B

STAY A

12 of 17

8-PIN CONNECTOR (White)

8-PIN CONNECTOR (Green)

55. Secure the connectors as shown.

56. Install the amplifier unit as shown.

AMPLIFIER UNIT

AMPLIFIER UNIT

STAY B

STAY A

<Left side>

57. Install the 5 mm nuts as shown.

5 mm NUT

AMPLIFIER UNIT

58. Remove the plug as shown.


<Left side>

<Left side>

PLUG (Save)

CLIP

12 PIN WATERPROOF CONNECTOR (Black)

13 of 17

MOTORCYCLE’S HARNESS

60. Move the motorcycle’s harnesses as shown.

62. Disconnect the motorcycle’s harness as shown.



61. Disconnect the 8P black connector as shown.



Move the left saddlebag catch and route the sub harness as shown.

64. Route the sub harness as shown.

63. Move the motorcycle’s harnesses to the positions shown.

SUB HARNESS

SUB HARNESS

LEFT SADDLEBAG CATCH

MOTORCYCLE’S HARNESSMove.


14 of 17

Fold back the motorcycle’s harness as shown.

65. Connect the sub harness to the motorcycle’s harness as shown.

SUB HARNESS




2-PIN WATERPROOF CONNECTOR (White)

66. Store the harness boots as shown.

67. Store the harness boot as shown.

SUB HARNESS

SUB HARNESS


HARNESS BOOT

HARNESS BOOT

CONNECTED 8-PIN WATERPROOF CONNECTOR (Black)

CONNECTED 2-PIN WATERPROOF CONNECTOR (White)

<Left side>

SUB HARNESS

GROMMET



15 of 17

69. Install the sub harness as shown.

SUB HARNESS

GROMMETInsert into the hole.

70. Install the left saddlebag catch in the reverse order of removal.

71. Connect the sub harness to the amplifier and install the clip to the stay as shown.

72. Install the well nut as shown.

SUB HARNESS

CLIP

WELL NUT


73. Clean the surface of the area shown using isopropyl alcohol as shown.

<Backside>

COVER

COVER

ISOPROPYL ALCOHOL

ISOPROPYL ALCOHOL

16 of 17

<Section View>

74. Attach the foam rubber seal to the cover as shown.

• Trim the excess end off the foam rubber seal.

COVER

COVER

FOAM RUBBER SEALRemove the adhesive backing before attaching.

FOAM RUBBER SEAL

5 mm SCREW (short)

5 mm SCREW (long)

5 mm SCREW (long)

75. Install the cover as shown.

• Confirm that any wire harness is not caught or too tight.

76. Install the 5 mm screw as shown.

COVER

COVER

5 mm SCREW (long)TORQUE: 0.3 N·m(0.03 kgf·m, 0.2 Ibf·ft)

ACCESSORY SPEAKER

TERMINAL JOINT

77. Connect the accessory speaker to the right rear speaker terminals as shown.

<Right rear>

17 of 17

SCREW (Reuse)

78. Install the right rear accessory speaker as shown.

ACCESSORY SPEAKER

OUTSIDE

TERMINAL

ACCESSORY SPEAKER

TERMINAL JOINT

79. Install the left rear accessory speaker in the same manner as the right side.

80. Connect the accessory speaker to the left front speaker terminals as shown.

<Left front>

SCREW (Reuse)

81. Install the left front accessory speaker as shown.

ACCESSORY SPEAKER

OUTSIDE

TERMINAL

82. Install the right front speaker in the same manner as the left front.

83. Install the motorcycle’s parts in the reverse order of removal.

• Confirm that any wire harness is not caught or too tight.

84. Check the power amplifier, speaker, headlight and the other lights for proper operation.

Honda Dealer: Please give a copy of these instructions to your customer.

INSTALLATIONINSTRUCTIONS

Accessory Application

© 2018 American Honda Motor Co., Inc. - All Rights Reserved.

PARTS LIST

87951-MKC-A0021 of 22

Publication No.

MII 16426

Issue Date

January 2018

POWER AMPLIFIER &SPEAKER KIT

P/N 08A83-MKC-A00GL1800B/BD

No. Description Qty

(1) Amplifier unit 1

(2) Stay A 1

(3) Stay B 1

(4) Sub harness 1

(5) Grommet 3

(6) Cover 1

(7) 5 mm screw (long) 4

(8) 5 mm screw (short) 2

(9) Collar 9

(10) 5 mm nut 5

(11) 4 mm screw 9

(12) Hole plug 1

(13) Well nut 1

(14) Speaker 4

(15) Sponge seal rubber 1


(14)

(15)

(4)

(5)

(16)

(1)

(6)

(2)(3)

(7)

(12)

(13)

(11)

(10)

(9)

(8)

2 of 22

REAR SPEAKER ATTACHMENT KITSold separately

TORQUE CHARTTighten all screws, bolts, and nuts to their specified torque values. Refer to the Service Manual for the torque values of the removed parts.

Item N·m kgf·m Ibf·ft

4 mm screw 1 0.1 0.7

5 mm screw 4.2 0.4 3.1

5 mm nut 5.2 0.5 3.8

TOOLS AND SUPPLIES REQUIREDBox-end wrench (8 mm)

Open-end wrench (8 mm)

Phillips screwdriver

Electric drill

Drill bit (4, 6 and 10 mm)

Hole saw (30 mm)

File

Snips

Dish soap solution

(Water:Dish soap / 100:1)

Isopropyl alcohol

Ruler

Scissors

Shop towel

Torque wrench

No. Description Qty


(2) Speaker right grill 1

(3) Speaker left grill 1

(4) Speaker right cover 1

(5) Speaker left cover 1

(6) Speed nut 9

(7) 5 mm screw 7

(8) Right sub harness 1

(9) Wire tie 4

(10) Left sub harness 1

(8)

(5)

(2)

(3)

(1)

(4)

(10)

(9)

(7)

(6)

3 of 22

INSTALLATION CAUTION

• To prevent burns, allow the engine, exhaust system, radiator, etc., to cool before installing the accessory.

NOTE:

• Heat the bonding surfaces with a hair dryer if the ambient air temperature is below 70°F (21°C).

• The adhesive reaches full strength in 72 hours. Wait at least 24 hours before riding your motorcycle.

• Disconnect the negative (-) cable from the battery before installing this accessory.

• The memory of the clock will be erased when you disconnect the battery. Reset the clock after reconnecting the battery.

• Reinstall the removed parts on the motorcycle and make sure that the wires and harnesses are not pinched.

1. Remove the left saddlebag guard cover as shown.<Left side>

LEFT SADDLEBAG GUARD COVER

LEFT MUFFLER

LEFT MUFFLERBOLTLoosen.

CLIP

BOLT

WASHER

SCREW

SCREW


3. Loosen the bolt, then remove the left muffler as shown.

4. Open the left saddlebag lid as shown.• Repeat on the right side.

<Left side>

LEFT SADDLEBAG LID

4 of 22

5. Remove the lef t s ide cover as shown, and disconnect the negative (-) cable of the battery.

LEFT SIDE COVER

6. Remove the right side cover in the same manner as the left side.

7. Remove the seat as shown.

BOLT

WASHER

SEAT

8. Remove the fuse holders as shown.<Left side>

FUSE HOLDERS

9. Remove the left pillion step holder cover as shown.• Repeat on the right side.

BOLT

SCREW

LEFT PILLION STEP HOLDER COVER

CLIP

5 of 22

10. Remove the right and left rear top lid as shown.RIGHT REAR TOP LIDLEFT REAR TOP LID

12. Remove the center rear top cover by pulling up and back as shown.

11. Remove the screws and clips as shown.SCREW

CENTER REAR TOP COVER

CENTER REAR TOP COVER

CLIP

WASHER

CABLE

RIGHT PASSENGER GRIP

13. Remove the right and left passenger grip as shown.

BOLT

LEFT PASSENGER GRIPRemove the cable.

14. Fold down the left rear view mirror backward as shown.

<Left side>

LEFT REAR VIEW MIRROR

15. Remove the left mirror arm panel as shown.

<Left side>

LEFT MIRROR ARM PANEL

SCREW

6 of 22


21. Remove the left inner cowl as shown.

19. Remove the left deflector panel as shown.

<Left side>

SCREW

SCREW

LEFT INNER COWL

CLIP

CLIP

SCREW

<Left side>

SCREW

LEFT DEFLECTOR PANEL

CLIP

<Left side>


CLIP

16. Remove the left rear view mirror as shown.

17. Remove the right mirror arm panel and right rear view mirror in the same manner as the left side.

18. Remove the screw as shown.• Repeat on the right side.

BOLT

LEFT REAR VIEW MIRRORDisconnect the connector.

7 of 22

23. Remove the left middle cowl as shown.

<Left side>

LEFT MIDDLE COWL

27. Remove the clip and disconnect the connector as shown.

26. Remove the connector as shown.

<Right side>2-PIN WATERPROOF CONNECTOR (Black)

CLIP


24. Remove the right deflector panel, right inner cowl and right middle cowl in the same manner as the left side.

25. Remove the parts as shown.• Repeat on the right side.

<Left side>

SCREW

SCREWCOLLAR

28. Remove the right outer air guide as shown.

SCREW

CLIPRIGHT OUTER AIR GUIDE

SCREW

8 of 22

29. Remove the pocket cable as shown.

POCKET CABLE


31. Remove the shelter as shown.

SCREW

CLIP

CLIP

SHELTER

32. Remove the left front speaker grill as shown.• Repeat on the right side.

LEFT FRONT SPEAKER GRILL

SCREW

CLIPCLIP

<Left side>

SCREWMETER


9 of 22


SPEAKER (Save)

35. Remove the right side speaker in the same manner as the left side.

36. Remove the clips as shown.• Repeat on the right side.

<Left side>CLIP

37. Remove the rear fender as shown.

SCREW

REAR FENDERDisconnect the connector.

38. Remove the saddlebag rear center cowl as shown.

39. Remove the parts as shown.• Repeat on the left side.

<Right side>

BOLTWASHER

SCREW

SCREW

SADDLEBAG REAR CENTER COWL

10 of 22



MARKED POINT

RIGHT SADDLEBAG UPPER COVER

MARKED POINT

42. Remove the speaker cover as shown.

43. Remove the left saddlebag upper cover and speaker cover in the same manner as the right side.

44. Drill at the marked points of the right saddlebag upper cover as shown.• Remove the any burrs from the edge of the

hole.

SCREW

SPEAKER COVER (Save)

41. Remove the right saddlebag upper cover as shown.

SCREW

SCREW

RIGHT SADDLEBAG UPPER COVERDisconnect the connector.

40. Remove the screw as shown.• Repeat on the left side.

SCREW

11 of 22

After cutting, finish with a file.

Discard.

46. Cut the left saddlebag upper cover in the same manner as the right side.





45. Drill at the marked lines of the right saddlebag upper cover as shown.• Drill holes at the center of the marked lines.

SNIPSCut the part.

MARKED LINE

MARKED LINE

MARKED LINE

FILEFile off the cutout surface.

47. Install the speaker right grill as shown.


SPEAKER RIGHT GRILL

SPEED NUT

48. Install the speaker left grill in the same manner as the right side.

49. Remove the plug as shown.• Repeat on the left side.

PLUG (Save)

<Right side>

12 of 22

52. Route the right sub harness as shown.

53. Install the right saddlebag in the reverse order of removal.

54. Remove the dummy connector as shown.

51. Move the right saddlebag and route the right sub harness as shown.• Repeat on the left side.

RIGHT SUB HARNESS


RIGHT SUB HARNESS

RIGHT SUB HARNESS



2-PIN WATERPROOF DUMMY CONNECTOR (Black) (Save)

GROMMET



RIGHT SUB HARNESS

RIGHT SADDLEBAG

Move.

13 of 22

57. Route the left sub harness as shown.

<Left side>

LEFT SUB HARNESS

LEFT SUB HARNESS

60. Connect the left sub harness as shown.



12-PIN WATERPROOF DUMMY CONNECTOR (Black) (Save)

55. Connect the right sub harness as shown.

56. Secure the right sub harness with the wire ties as shown.

RIGHT SUB HARNESS

RIGHT SUB HARNESS


WIRE TIESecure the right sub harness to the motorcycle’s harness.

WIRE TIESecure the right sub harness to the motorcycle’s harness.


58. Install the left saddlebag in the reverse order of removal.

59. Remove the dummy connector as shown.

14 of 22

62. Remove the screws as shown.SCREW

<Left side>

61. Remove the plugs as shown.

63. Remove the left saddlebag rear cover as shown.

SCREW

LEFT SADDLEBAG REAR COVER

CLIPSCREW

64. Drill 30 mm hole at each marked line of the left saddlebag as shown.• Drill holes at the center of the marked lines.• Remove the any burrs from the edge of the

hole.

MARKED LINE

ELECTRIC DRILL (30 mm HOLE SAW)

LEFT SADDLEBAG

65. Drill a 6 mm hole each marked point of the left saddlebag as shown.• Remove the any burrs from the edge of the

hole.<Under side>

MARKED POINT

LEFT SADDLEBAG


PLUG (Save)

PLUG (Save)

15 of 22

Align the end of grommet with the marked line as shown.

67. Install the grommets at positions shown.

68. Install the hole plug as shown.

HOLE PLUG

STAY A

GROMMET

GROMMETMARKED LINE

GROMMET

66. Apply dish soap solution to the position shown.• Perform this step for all three grommets.


69. Install stay-B to the amplifier unit with the screws andcollars as shown.

70. Install stay-A to the amplifier unit with the screws andcollars as shown.

AMPLIFIER UNIT

AMPLIFIER UNIT

4 mm SCREW

4 mm SCREW

COLLAR

COLLAR

STAY B

STAY A

16 of 22

8-PIN CONNECTOR (White)


71. Secure the connectors as shown.

72. Install the amplifier unit as shown.

AMPLIFIER UNIT

AMPLIFIER UNIT

STAY B

STAY A

<Left side>

73. Install the 5 mm nuts as shown.

5 mm NUT


<Left side>

CLIP

12 PIN WATERPROOF CONNECTOR (Black)

74. Remove the plug as shown.

<Left side>PLUG (Save)

AMPLIFIER UNIT

17 of 22

76. Move the motorcycle’s harnesses as shown.


77. Disconnect the 8P black connector as shown.

Move the left saddlebag catch and route the sub harness as shown.

79. Route the sub harness as shown.

78. Move the motorcycle’s harnesses to the positions shown.

SUB HARNESS

SUB HARNESS

LEFT SADDLEBAG CATCH



LEFT SUB HARNESS



18 of 22

80. Connect the sub harness to the motorcycle’s harnessas shown.

81. Store the harness boots as shown.

<Left side>

Fold back the motorcycle’s harness as shown.

82. Store the boot as shown.

SUB HARNESS

GROMMET



SUB HARNESS



2-PIN WATERPROOF CONNECTOR (White)

SUB HARNESS


HARNESS BOOT

CONNECTED 8-PIN WATERPROOF CONNECTOR (Black)

CONNECTED 2-PIN WATERPROOF CONNECTOR (White)

HARNESS BOOT


SUB HARNESS

19 of 22

86. Install the left saddlebag catch in the reverse order of removal.

87. Connect the sub harness to the amplifier and install the clip to the stay as shown.

88. Install the well nut as shown.

WELL NUT

84. Install the sub harness as shown.


SUB HARNESS

CLIP


LEFT SUB HARNESSWIRE TIESecure the left sub harness to the motorcycle’s harness.

85. Secure the left sub harness with the wire tie as shown.

SUB HARNESS

20 of 22

89. Clean the surface of the area shown using isopropyl alcohol.

<Backside>

COVER

COVER

ISOPROPYL ALCOHOLThoroughly clean the area where the sponge seal rubber will be attached.

ISOPROPYL ALCOHOLThoroughly clean the area where the sponge seal rubber will be attached.

<Section View>

90. Attach the sponge seal rubber as shown.• Trim the excess end off the sponge seal rubber.

COVER

COVER

SPONGE SEAL RUBBERRemove the adhesive backing before attaching.

SPONGE SEAL RUBBER

5 mm SCREW (long)

5 mm SCREW (long)

91. Install the cover as shown.• Confirm that any wire harness is not caught or

too tight.

COVER

5 mm SCREW (long)TORQUE: 0.3 N·m(0.03 kgf·m, 0.2 Ibf·ft)

21 of 22

93. Install the accessory speaker as shown.

<Right side>SCREW (Reuse)

ACCESSORY SPEAKER

ACCESSORY SPEAKER

OUTSIDE

TERMINAL

94. Connect the right sub harness as shown.

95. Install the speaker right cover as shown.

5 mm SCREW

TERMINAL

RIGHT SUB HARNESS

SPEAKER RIGHT COVER

96. Install the left side accessory speaker and speaker left cover in the same manner as the right side.

5 mm SCREW (short)

92. Install the 5 mm screw as shown.

COVER

22 of 22

99. Install the right side accessory speaker in the same manner as the left side.

100. Install the motorcycle’s parts in the reverse order of removal.• Confirm that any wire harness is not caught or

too tight.101. Check the power amplifier, speaker, headlight and

the other lights for proper operation.

ACCESSORY SPEAKER

TERMINAL JOINT

97. Connect the accessory speaker as shown.

<Left side>

SCREW (Reuse)

98. Install the accessory speaker as shown.

ACCESSORY SPEAKER

OUTSIDE

TERMINAL

installation gl1800/d/da instructions p/n...

Documents