installation cd changer 2009 civic … · © 2008 american honda motor co., inc. - all rights...

© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 40184 (0808) 1 of 1108V31-SDN-1010-91

PARTS LIST

2 Side brackets

3 Clip nuts

3 EPT seals

8 Cushion tapes

3 Washer-bolts

4 Flange nuts

15 Wire ties

Bus cable

4 Washer-screws

2 Wire ties with clip

CD changer

Bracket (Not Used)

8-Disc CD magazine

8 Washer-screws, 4 x 6 mm

INSTALLATIONINSTRUCTIONS

Accessory Application Publications No.

Issue Date

AUG 2008

2009 CIVIC4-DOOR

CD CHANGER(Trunk Mount)

Accessory user'sinformation manual

CD changer bracket

CD Changer Attachment (Sold Separately)P/N 08B26-SNA-101

AII 40184

CD Changer Kit (Sold Separately)P/N 08A26-5E1-101

2 of 11 AII 40184 (0808) © 2008 American Honda Motor Co., Inc. - All Rights Reserved.

TOOLS REQUIRED

Phillips screwdriver

Flat-tip screwdriver

Stubby Phillips screwdriver

10 mm combination wrench

Clip remover

8 mm and 10 mm Sockets

Ratchet

Small flat-tip screwdriver

Contact cleaner

Shop towel

Illustration of the CD Changer Installed on theVehicle

INSTALLATION

Customer Information: The information in thisinstallation instruction is intended for use onlyby skilled technicians who have the propertools, equipment, and training to correctly andsafely add equipment to your car. Theseprocedures should not be attempted by “do-it-yourselfers.”

Routing the Fog Light Harness

1. Make sure you have the anti-theft code forthe audio unit, then write down thefrequencies for the preset buttons.

2. Disconnect the negative cable from thebattery.

4. Remove the right rear seatback side frame byremoving the bolt.

3. Inside the passenger's compartment area, removethe rear seat cushion by removing the bolt andreleasing the two hooks.

H

AUDIO UNIT

BUS CABLE

CD CHANGER

T

BOLT

HOOKS REAR SEAT CUSHION

T

RIGHTREAR SEATBACKSIDE FRAME

BOLT

© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 40184 (0808) 3 of 11

5. Open the trunk lid, and remove the trunk floor byremoving the two clips.

6. Remove the trunk weatherstrip from the edge ofthe trunk opening in the area shown.

7. Remove the rear trim panel by removing the fourclips and releasing the two hooks.

8. Inside the trunk, fold the right rear seatbackforward by pulling the lever under the rear parcelshelf.

9. Continue removing the weatherstrip in the areashown. Remove the five clips, then pull out on theright trunk side trim panel in the direction shown.

TRUNKFLOORMAT

2 CLIPS

TRUNKWEATHERSTRIP

4 CLIPSREAR TRIMPANEL

2 HOOKS

LEVER

RIGHT REARSEATBACK

RIGHT TRUNK SIDETRIM PANEL

CLIPS

CLIPS(Turn the center pinin a counterclockwisedirection to remove.)

CLIPS(Turn the center pinin a counterclockwisedirection to remove.)


A/T Vehicle

• Remove the center console cover by removing thethree clips that fasten the center console cover.

11. Open the center console lid, and remove the mat.

12. Remove the two self-tapping screws, two screws,and two clips that fasten the center console, thenremove the center console.

• Remove the center console cover by removing thethree clips that fasten the center console cover.

10. Remove the center console cover.

M/T Vehicle

• Pull down on the shift boot, then loosen thefastening nut by turning it counterclockwise.

• Remove the shift knob by turning itcounterclockwise. Remove the fastening nut byturning it clockwise.

SHIFT KNOB

FASTENING NUT

SHIFT BOOT

3 CLIPSCENTERCONSOLECOVER

PARKING BRAKE LEVER(Pull up completely.)

3 CLIPS CENTERCONSOLECOVER

PARKING BRAKE LEVER(Pull up completely.)

CENTERCONSOLE

2 SCREWS

2 CLIPS

MAT SELF-TAPPINGSCREWS

CENTERCONSOLELID


14. Release the eight clips, and remove the driver'sdashboard lower cover by pulling it toward you.Take care not to damage the clips.

13. Turn the knob counterclockwise, release the twoclips and remove the driver's dashboard undercover by lowering the cover and pulling it towardyou. Take care not to damage the clips.

15. Release the four clips, and remove thepassenger's dashboard under cover by pulling ittoward you. Take care not to damage the clipsand pins.

16. Release the two hooks and remove the lid abovethe front console pocket.

FRONT CONSOLEPOCKET

LID2 HOOKS

PASSENGER’SDASHBOARD UNDER COVER

4 CLIPS

2 PINS

DRIVER’S DASHBOARDUNDER COVER

2 CLIPS

KNOB(Turn counter-clockwise.)

8 CLIPS

DASHBOARDLOWER COVER


17. Remove the two bolts from the bottom of thecenter panel.

18. Release the ten retaining clips, and pull the centerpanel toward you.

19. Unplug the right vehicle connectors, then removethe center panel.

Routing the Bus cable

20. Route the bus cable along the vehicle harnessfrom the trunk side.

21. Return the right rear seatback, then remove theclip securing the floor carpet. Turn over the floorcarpet.

22. Route the bus cable connector as shown.

BUS CABLE

RIGHT REARSEATBACK

FLOOR CARPET

BUSCABLE

Routeunder thefloorcarpet.

10 CLIPS

BOLTS


23. Route the bus cable forward to the right frontconsole frame along the vehicle harness.

24. Route the bus cable connector to the dashboardand out through the dash opening.

BUS CABLE

DASH OPENING

VEHICLEHARNESS

DASH OPENING

25. Measure 300 mm from the end of the bus cableconnector, then secure the bus cable to thevehicle harness with three wire ties.

WIRE TIES

BUS CABLECONNECTOR

300 mm

26. Secure the bus cable to the vehicle harness withfive wire ties.

27. Using isopropyl alcohol on a shop towel, clean thearea where the cushion tape will attach. Attach thebus cable to the floor panel with the two cushiontapes in the area shown.

VEHICLEHARNESS

BUS CABLE

CUSHIONTAPES

WIRE TIES

With the vehicle bracketUsing the isopropyl alcohol on a shop towel, cleanthe inside of the vehicle bracket where thecushion tape attaches. Attach the cushion tape onthe vehicle bracket at the location shown.

CUSHIONTAPE

VEHICLEBRACKET

BUS CABLE

ATTACHMENTLOCATION


28. Turn over the floor carpet, and attach the buscable to the floor panel with the three cushiontapes in the areas shown.

29. Secure the bus cable to the vehicle harness withthe five wire ties in the areas shown.

Installing the CD Changer

30. Carefully unpack the CD changer.

31. The adjustment knobs have been set to thevertical (V) position before shipping the CDchanger from the factory. Move the adjustmentknobs to the horizontal (H) position using a smallflat-tip screwdriver.

32. Position the CD changer brackets on the sides ofthe CD changer, then install the four 4 x 8 mmwasher-screws.

2 4 x 8 mmWASHER-SCREWS

SIDE BRACKETS

CDCHANGER

2 4 x 8 mmWASHER-SCREWS

WIRE TIES

VEHICLEHARNESS

CUSHIONTAPES

BUS CABLE

Turn over.

CUSHION TAPE

POSITION) AFTER SETTING)

VERTICAL HORIZONTAL

KNOBCHANGER


33. Position the CD changer on the CD changerbracket, then install and tighten the four 6 mmflange nuts.

34. Wrap one EPT sealer around the bus cableconnector from the CD changer, then secure thebus cable and connector to the CD changerbracket with the two wire ties you just installed.

35. In the trunk, slide the clip nut into position on therear seat panel through the hole in the panel. Ifnecessary, spread the clip nuts open with a smallflat-tip screwdriver.

36. Loosely install the washer-bolt to the rear seatpanel first. Then place the end of the CD changerbracket between the seat panel and the clip nutyou just installed.

CLIP NUT

WASHER-BOLT

CDCHANGER

CD CHANGER BRACKET(Place the end of thebracket between theseat panel and clip nutyou just installed.)

CD CHANGERBRACKET

CDCHANGER

WIRE TIES

EPT SEALER

CD CHANGERBUS CABLECONNECTOR

CDCHANGER

CD CHANGERBRACKET

4 FLANGE NUTS


37. Slide the two clip nuts onto the CD changerbrackets and rear shelf through the holes in theparcel shelf, and align their holes as shown. Installthe two washer-bolts, and tighten them securely.

38. Connect the bus cable connector to the CDchanger connector from the CD changer.

CD CHANGER

BUS CABLE

BUS CABLECONNECTOR CD CHANGER

CONNECTOR

39. Fold the excess bus cable and secure the buscable to the holes of the rear seat panel with thetwo wire ties with clip.

CD CHANGER

RIGHTSEAT PANEL

BUS CABLE

2 WIRE TIES WITH CLIP

Fold the excesscables.

WASHER-BOLTS

CDCHANGERBRACKET CLIP NUTS

CLIP NUT

CDCHANGERBRACKET

REAR SHELF


40. Plug the bus cable connector, vehicle 20-pinconnector (blue), and antenna lead into the rear ofthe audio unit.

STANDARD AUDIO UNIT

VEHICLE 20-PINCONNECTOR

BUS CABLEANTENNALEAD

MULTI CONTROL CD TUNER UNIT

BUS CABLE

VEHICLE 20-PINCONNECTOR�ANTENNA

LEAD

CD PLAYER

POCKET

NAVIGATION HEAD UNIT

�


BUS CABLEANTENNALEAD

41. Connect the four vehicle connectors to the centerpanel, and reinstall the center panel.

42. Check that all wire harnesses are routed properlyand that all connectors are plugged in.

43. Reconnect the negative cable to the battery.

44. Reset the clock and the radio station presets.

45. Check the operation of the CD changer asdescribed in the accessory user's informationmanual.

46. Reinstall all removed parts. Be sure that allretaining clips and tabs are secrely fastened.

47. Put the accessory user's information manual inthe glove box for your customer.

48. Initialize and test the front window auto up/downfunction.

CENTER PANEL

4 VEHICLE CONNECTORS

BOLTS(reused)


ANTENNALEAD

BUS CORDCONNECTOR

installation cd changer 2009 civic … · © 2008 american honda motor co., inc. - all rights...

Documents