installation bii 50164 instructions 2014 tl aug 2013 · 2014. 11. 24. · bii 50164 (1308) 3 of 22...
TRANSCRIPT
© 2013 American Honda Motor Co., Inc. – All Rights Re
BII 50164
Publications No.
INSTALLATIONINSTRUCTIONS
Accessory Application
REMOTE CONTROLENGINE STARTER
served. BII 50164 (1308
2014 TL
) 0
Issue Date
AUG 2013
PARTS LIST
Remote Control Engine Starter Unit KitP/N 08E91-TK4-200A
Transmitter
Control unit
Antenna
Key ring
Protective tape
Caution label
Fuse label
Accessory User’s Information Manual
Quick Start Guide
Remote Control Engine Starter Attachment KitP/N 08E92-TK4-200C
Engine starter harness
Control unit bracket
3 Relays
1 of 228E92-TK4-2C00-90
21 Wire ties
6 Urethane tapes
Template
A-pillar clip
Flange nut
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Flat-tip screwdriver
Small flat-tip screwdriver
Ratchet
10 mm and 12 mm Sockets
10 mm Combination wrench
Diagonal cutters
Isopropyl alcohol
Shop towel
Tape measure
Scissors
Rubber mallet
HDS
Masking tape
2 Pairs of needle nose pliers
Plastic Trim Tool (T/N SILTRIMTL10)
Ruler
2 of 22 BII 50164
Illustration of the Remote Control Engine Starter in the Vehicle
INSTALLATION
NOTE: The antenna should be installed only if the ambient air temperature is 15°C (60°F) or above.
1. Make sure you have the anti-theft codes for the audio and navigation system (if equipped), then write down the audio presets.
Client Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
0D0601A�
ENGINE STARTER HARNESS
ANTENNA
RELAYS
3A FUSES
CONTROL UNIT
40A FUSE BLOCK
(1308) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
If the vehicle is equipped with the keyless start system, go to step 2; if not, go to step 4.
2. Check the settings of the switches on the control unit.NOTE: If the switch settings are not correct, the remote control engine starter will not operate correctly.
3. Using a small flat-tip screw driver, set the switches on the control unit as shown. Go to step 6.
NOTE:
• Set the switches before plugging in the control unit.
• If you are setting the switches with the control unit installed in the vehicle, touch the metal part of the screwdriver to any metal part of the vehicle to discharge any static electricity.
• If you change the switch settings with the unit connected, you must disconnect the unit, then reconnect it before the new settings are recognized.
925003AT
CONTROL UNIT
Discharge any static electricity.
SET
SWITCHES
SWITCHES
SW:1 RR Junction unit ------------------- > OFF
SW:2 Trunk or Tailgate ------------------- > OFF
SW:3 Smart Entry--------------------------- > ON
SW:4 Horn or Buzzer Answerback---- > OFF
SW:5 Trunk Main SW ---------------------- > OFF
SW:6 Reserve -------------------------------- > OFF
SMALL FLAT-TIP SCREW-DRIVER
FOR VEHICLES WITH KEYLESS START SYSTEM
© 2013 American Honda Motor Co., Inc. – All Rights Reserved. BII 50164
4. Check the settings of the switches on the control unit.NOTE: If the switch settings are not correct, the remote control engine starter will not operate correctly.
5. Using a small flat-tip screw driver, set the switches on the control unit as shown. NOTE:
• Set the switches before plugging in the control unit.
• If you are setting the switches with the control unit installed in the vehicle, touch the metal part of the screwdriver to any metal part of the vehicle to discharge any static electricity.
• If you change the switch settings with the unit connected, you must disconnect the unit, then reconnect it before the new settings are recognized.
001501A�
CONTROL UNIT
Discharge any static electricity.
SET
SWITCHES
SWITCHES
SW:1 RR Junction unit ------------------- > OFF
SW:2 Trunk or Tailgate ------------------- > OFF
SW:3 Smart Entry--------------------------- > OFF
SW:4 Horn or Buzzer Answerback---- > OFF
SW:5 Trunk Main SW ---------------------- > OFF
SW:6 Reserve -------------------------------- > OFF
SMALL FLAT-TIP SCREW-DRIVER
FOR VEHICLES WITHOUT KEYLESS START SYSTEM
(1308) 3 of 22
6. Using isopropyl alcohol on a shop towel, clean the control unit where the protective tape will attach. Remove the adhesive backing, and attach the protective tape to the control unit over the switch opening.
7. Lower the tilt lever and pull the steering wheel out. Remove the two lower self-tapping screws and the lower screw.
8. Turn the steering wheel as necessary to access each self-tapping screw, and remove the two self-tapping screws.
772505AS
CONTROL UNIT
SWITCH OPENING
PROTECTIVE TAPE
ADHESIVE BACKING
Clean with isopropyl alcohol.
830618BT
SELF-TAPPING SCREWS
LOWER SCREW
LOWER SELF-TAPPING SCREWS
TILT LEVER
4 of 22 BII 50164
9. Remove the upper steering column cover and the lower steering column cover:
• Starting with the left side, use a small flat-tip screwdriver to push in to release the tab, then push in on the side of the upper steering column cover in the area shown to release the rear tab.
• Shift the column covers to the right, and repeat the same procedure.
• Release the four hooks, and remove the upper steering column cover and the lower steering column cover.
830617BT
SMALL FLAT-TIP SCREWDRIVERPush on tabs.
Push.
Push.
2 REAR TABS
2 HOOKS
2 HOOKS
UPPER STEERING COLUMN COVER
LOWER STEERING COLUMN COVER
(1308) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
10. Open the hood. Remove the front bulkhead cover (four clips and two hooks).
11. Disconnect the negative cable from the battery.
831801BH
FRONT BULKHEAD COVER4 CLIPS
HOOK
HOOK
© 2013 American Honda Motor Co., Inc. – All Rights Reserved. BII 50164
12. Remove the roof console:
• Open the sunglass holder, and remove two self-tapping screws.
• Release two clips, and pull the roof console toward you.
• Unplug the vehicle connectors to remove the roof console.
13. Remove the two sunvisor holders by turning each holder 45°.
830606BT
ROOFCONSOLE
VEHICLE CONNECTORS
SELF-TAPPING SCREWS
SUNGLASS HOLDEROpen.
2 CLIPS
830653AT
Turn.
2 SUNVISOR HOLDERS
(1308) 5 of 22
14. Remove the left sunvisor.
• Pivot the left sunvisor downward.
• Locate the slot in the sunvisor holder, and insert a flat-tip screwdriver into the slot. Push in and hold the retaining tab.
• While holding the retaining tab, rotate the sunvisor toward the door to remove it.
• Unplug the vanity mirror light connector.
NOTE: If the retaining tab did not stay pushed in, return the left sunvisor to its original position and repeat the steps above.
A11301A�SLOTHOLDER
Push and hold the retaining tab.
FLAT-TIPSCREWDRIVER
LEFTSUNVISOR
Rotatetowardsthe door.
VANITY MIRROR LIGHT CONNECTOR
FRONT
6 of 22 BII 50164
15. Pull away the door opening trim from the left front A-pillar trim.
16. Using a rubber mallet and a shop towel, tap the left front A-pillar trim at the position shown to release the clip.
17. Pull away the door opening trim, and remove the left front A-pillar trim (one clip, and unplug the vehicle connector).
830602BT
DOOR OPENING TRIM
LEFT FRONT A-PILLAR TRIM
CLIPFRONT PILLAR
PIN
Strike perpendicularly to the vehicle.
LEFT FRONT A-PILLAR TRIM
SHOP TOWEL
RUBBER MALLET
CLIP
25 mm (1.0 in.)
830603AT
LEFT FRONT A-PILLAR TRIM
CLIP
DOOR OPENING TRIM
VEHICLE CONNECTOR
(1308) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
18. Remove and discard the clip from the left frontA-pillar trim, and install a new A-pillar clip (supplied).
19. Using a plastic trim tool, remove the left dashboard side cover (four clips and four hooks).
830604AT
CLIPDiscard.
LEFT FRONTA-PILLAR TRIM
NEW A-PILLAR CLIP
830614BT
LEFT DASHBOARD SIDE COVER
4 CLIPS
4 HOOKS
© 2013 American Honda Motor Co., Inc. – All Rights Reserved. BII 50164
20. Remove the driver’s dashboard under cover:
• Turn the knob counterclockwise.
• Release two clips and one pin, then pull the driver’s dashboard under cover toward you.
• Unplug the vehicle connector, and release the harness clip to remove the driver’s dashboard under cover.
21. Remove the left front door sill trim (four clips and three retaining tabs).
830607AT
DRIVER’S DASHBOARD UNDER COVER
2 CLIPS
PIN
VEHICLE CONNECTOR
KNOBTurn.
HARNESS CLIP
830608AT
FRONT
LEFT FRONT DOOR SILL TRIM
4 CLIPS
3 RETAINING TABS
(1308) 7 of 22
22. Pull away the door opening trim, and remove the left kick panel (two clips).
23. Using scissors, cut out the template.
830609AT
LEFT KICK PANEL
2 CLIPS
DOOR OPENING TRIM
830619AT
Cut out.
TEMPLATE
SCISSORS
8 of 22 BII 50164
24. Using masking tape, attach the template to the windshield. Align with the black ceramic as shown.
25. Bend the antenna plate according to the full scale drawing shown. Use two pairs of needle nose pliers as shown.
830620AT
WINDSHIELD
TEMPLATE
MASKING TAPE
Align with the black ceramic.
BLACK CERAMIC
9D0728A�
ANTENNA
ANTENNA PLATE
25 mm (0.98 in.)
SCALE
2 PAIRS OF NEEDLE NOSEPLIERS
12 mm (0.47 in.)
7 mm (0.28 in.)
(1308) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
26. Starting at the antenna end of the cable, wrap three urethane tapes around the antenna cable at the measurements shown.
27. Using scissors, cut one urethane tape in half. Wrap the two halves of the urethane tape around the antenna cable at the measurements shown.
830622AT
400 mm(16 in.)
40 mm (1.6 in.)
40 mm (1.6 in.)
750 mm (30 in.)
ANTENNA CABLE
3 URETHANE TAPES
ANTENNA CABLE
URETHANE TAPECut in half.
2 URETHANE TAPE HALVES
ANTENNA
50 mm (2.0 in.)
© 2013 American Honda Motor Co., Inc. – All Rights Reserved. BII 50164
28. Using isopropyl alcohol on a shop towel, clean the area where the antenna will attach.
29. Remove the adhesive backing from the antenna. Insert the antenna plate behind the headliner, align the antenna with the template, and attach the antenna to the windshield. Make sure the antenna is attached firmly to the windshield.
30. Remove the template.
31. Route the antenna cable towards the driver’s side of the vehicle. Gently pull down the headliner, and tuck the antenna cable behind it. Be careful not to crease the headliner.
830623AT
TEMPLATE
HEADLINER
ANTENNA
ANTENNA PLATE
ADHESIVE BACKINGRemove.
WINDSHIELDClean with isopropyl alcohol.
830624BT
HEADLINER
ANTENNA CABLE
(1308) 9 of 22
32. Using isopropyl alcohol on a shop towel, clean the area where the urethane tapes will attach.
33. Using scissors, cut one urethane tape in half. Secure the antenna cable to the roof panel with the two halves of urethane tape.
34. Secure the antenna cable to the vehicle harness with six wire ties.
830625AT
ANTENNA CABLE
ROOF PANELClean with isopropyl alcohol.
2 URETHANE TAPE HALVES
URETHANE TAPECut in half.
830626AT
6 WIRE TIES
ANTENNA CABLE
VEHICLE HARNESS
10 of 22 BII 50164
35. Pull away the door opening trim from the left front A-pillar. Route the antenna cable down next to the dashboard, and tuck the antenna cable between the left front A-pillar and the dashboard. Reinstall the door opening trim.
36. Route the antenna cable along the vehicle harness as shown.
830627BT
ANTENNA CABLELEFT FRONT A-PILLAR
DASHBOARD
DOOR OPENING TRIM
830628CT
ANTENNA CABLE
VEHICLE HARNESS
(1308) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
37. Using isopropyl alcohol on a shop towel, clean the area where the fuse labels will attach.
38. Attach the 40A and 3A fuse labels to the engine starter harness fuse block.
39. Install the three relays on the engine starter harness relay block.
40. Plug the antenna terminal into the control unit.
41. Plug the engine starter harness 28-pin connector into the control unit.
42. Install the control unit bracket to the control unit.
862703AT
RELAY BLOCK
RELAYS
FUSE BLOCK
40A FUSE LABEL
ENGINE STARTER HARNESS
Clean with isopropyl alcohol.
3A FUSE LABEL
830631AT
ANTENNA TERMINAL
CONTROL UNIT
ENGINE STARTERHARNESS 28-PINCONNECTOR
© 2013 American Honda Motor Co., Inc. – All Rights Reserved. BII 50164
43. Attach the engine starter harness relay and fuse blocks onto the control unit bracket.
44. Remove the vehicle nut from the vehicle bracket, and secure the control unit bracket to the vehicle bracket with one flange nut and one vehicle nut.
830632AT
CONTROL UNIT BRACKET
CONTROL UNIT
862704AT
CONTROL UNIT BRACKET
CLIPRELAY BLOCK
FUSE BLOCK
ENGINE STARTER HARNESS
(1308) 11 of 22
45. Unplug the vehicle 24-pin connector (White) from the bottom of the fuse box, and plug it into the engine starter harness 24-pin connector. Plug the remaining engine starter harness 24-pin connector into the fuse box 24-pin connector (White).
46. Attach the clip on the engine starter harness 24-pin connector to the clip holder on the bottom of the fuse box as shown.
830634BT
FLANGE NUT
CONTROL UNIT BRACKET
VEHICLE BRACKET
VEHICLE NUT Reuse.
VEHICLE BRACKET
CONTROL UNIT BRACKET
862707AT
FUSE BOX
FUSE BOX 24-PIN CONNECTOR (White)
VEHICLE 24-PIN CONNECTOR (White)
ENGINE STARTER HARNESS 24-PIN CONNECTOR
ENGINE STARTER HARNESS 24-PIN CONNECTOR
FUSE BOX 24-PIN CONNECTOR (White)
FUSE BOX
12 of 22 BII 50164
47. Unplug the vehicle 20-pin connector (Green) from the fuse box, and plug it into the engine starter harness 20-pin connector. Plug the remaining engine starter harness 20-pin connector into the fuse box 20-pin connector.
862708AT
FUSE BOX
ATTACHMENT POSITION
FUSE BOX
ENGINE STARTER HARNESS 24-PIN CONNECTOR(Plugged in step 45.)
CLIP HOLDER
862709AT
FUSE BOX 20-PIN CONNECTOR
FUSE BOX
VEHICLE 20-PIN CONNECTOR (Green)
ENGINE STARTER HARNESS 20-PIN CONNECTORS
FUSE BOX
FUSE BOX 20-PIN CONNECTOR
(1308) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
48. Cut one urethane tape to the dimensions shown, and wrap it around the engine starter harness 5-pin connector as shown.
001502B�
Do not cover this area.
ENGINE STARTER HARNESS 5-PIN CONNECTOR
URETHANE TAPE
Discard.
20 mm (0.8 in.)
25 mm (1.0 in.)
URETHANE TAPE
ENGINE STARTER HARNESS 5-PIN CONNECTOR
VIEWED FROM URETHANE SIDE
© 2013 American Honda Motor Co., Inc. – All Rights Reserved. BII 50164
49. Unplug the vehicle 5-pin connector from the fuse box, and plug it into the engine starter harness 5-pin connector. Plug the remaining engine starter harness 5-pin connector into the fuse box 5-pin connector.
NOTE: Make sure the engine starter harness 5-pin connectors are securely connected to the fuse box 5-pin connector and vehicle 5-pin connector. A loose connection can cause the engine to stall while driving.
001503A�
Connector unlock
Push.
Push.
Connector lock
12
31
2
Pull.
VEHICLE 5-PIN CONNECTOR
FUSE BOX
FUSE BOX 5-PIN CONNECTOR
ENGINE STARTER HARNESS 5-PIN CONNECTORS
Push. 2
Push.1
Connector lockFUSE BOX 5-PIN CONNECTOR
FUSE BOX
(1308) 13 of 22
50. Plug the engine starter harness 12-pin connector into the fuse box 12-pin connector.
51. Secure the engine starter harness 5-pin connector and the engine starter harness to the vehicle harness with one wire tie.
001504A�
FUSE BOX 12-PIN CONNECTOR
FUSE BOX
FUSE BOXENGINE STARTER HARNESS
ENGINE STARTER HARNESS 12-PIN CONNECTOR
001505A�
WIRE TIE
VEHICLE HARNESS
ENGINE STARTER HARNESS
ENGINE STARTER HARNESS 5-PIN CONNECTOR
14 of 22 BII 50164
52. Remove the vehicle ground bolt. Attach the engine starter harness ground terminal to the vehicle ground terminal, and reinstall the vehicle ground bolt.
53. Secure the antenna cable and engine starter harness to the vehicle harness with four wire ties.
54. Bundle up the excess antenna cable as shown, and secure it to the vehicle harness with one wire tie.
830636CT
VEHICLE GROUND BOLTReuse.
VEHICLE GROUND TERMINAL
ENGINE STARTER HARNESS GROUND TERMINAL
VEHICLE HARNESS
ENGINE STARTER HARNESS
830644BT
4 WIRE TIES
ENGINE STARTER HARNESS
VEHICLE HARNESS
WIRE TIE
ANTENNA CABLEBundle up the excess.
(1308) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
55. To gain access to route the engine starter harness, remove the vehicle bolt from the vehicle bracket, and move the vehicle unit.
56. Attach the engine starter harness clip to the vehicle bracket.
57. Align the white tape on the engine starter harness with the vehicle clip, and secure the engine starter harness to the vehicle harness with two wire ties.
58. Reinstall the vehicle unit.
830657AT
VEHICLE UNIT
VEHICLE BOLT
VEHICLE BRACKET
CONTROL UNIT
830645DT
ENGINE STARTER HARNESSVEHICLE
HARNESS
WIRE TIE
WHITE TAPE
VEHICLE CLIPENGINE STARTER HARNESS CLIP
VEHICLE BRACKET
WIRE TIE
VEHICLE CLIP
© 2013 American Honda Motor Co., Inc. – All Rights Reserved. BII 50164
59. Route two 12-pin connectors and two 8-pin connectors on the engine starter harness along the vehicle harness as shown.
60. Route two 12-pin connectors and two 8-pin connectors on the engine starter harness along the vehicle harness as shown.
830646AT
ENGINE STARTER HARNESS 12-PIN CONNECTORS
ENGINE STARTER HARNESS 8-PIN CONNECTORS
VEHICLE HARNESS
830658AT
ENGINE STARTER HARNESS 12-PIN CONNECTORS
ENGINE STARTER HARNESS 8-PIN CONNECTORS
VEHICLE HARNESS
(1308) 15 of 22
61. Unplug the vehicle 12-pin connector from the turn signal switch, and plug it into the engine starter harness 12-pin connector. Plug the remaining engine starter harness 12-pin connector into the turn signal switch.
62. Unplug the vehicle 8-pin connector from the wiper switch, and plug it into the engine starter harness 8-pin connector. Plug the remaining engine starter harness 8-pin connector into the wiper switch.
830647AT
ENGINE STARTER HARNESS 12-PIN CONNECTORS
VEHICLE 12-PIN CONNECTOR
TURN SIGNAL SWITCH
830648AT
ENGINE STARTER HARNESS 8-PIN CONNECTORS
VEHICLE 8-PIN CONNECTOR
WIPER SWITCH
16 of 22 BII 50164
63. Secure the engine starter harness to the vehicle harness with four wire ties. Do not secure it to the SRS harness.
64. Secure the engine starter harness to the vehicle harness with one wire tie.
830649AT
WIRE TIE
VEHICLE HARNESS
ENGINE STARTER HARNESS
WIRE TIE
WIRE TIE
WIRE TIE
830650AT
WIRE TIE
VEHICLE HARNESS
ENGINE STARTER HARNESS
(1308) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
65. Secure the engine starter harness to the vehicle harness with two wire ties as shown.
66. Using isopropyl alcohol on a shop towel, clean the area where the caution label will attach.
67. Attach the caution label to the hood in the area shown.
830651CT
WIRE TIES
VEHICLE HARNESSENGINE STARTER HARNESS
VEHICLE CLIP
VEHICLE CLIP
925002AT
Clean with isopropyl alcohol.
HOOD
CAUTION LABEL
© 2013 American Honda Motor Co., Inc. – All Rights Reserved. BII 50164
68. Check that all wire harnesses and cables are routed properly and that all connectors are plugged in.
69. Reinstall all removed parts except for the front bulkhead cover. Take care not to pinch the side curtain airbag with the clip during reinstallation of the left front A-pillar trim. Do not push on the front pillar trim excessively.
70. Reconnect the negative cable to the battery.
71. Check the operation of the headlights and windshield wipers/washers.
72. Reinstall the front bulkhead cover.
73. Enter the anti-theft codes for the audio system and the navigation system (if equipped).
74. Reset the clock on vehicles without navigation.
75. Do the REMOTE ENGINE STARTER REGISTRATION (Page 18), and the FUNCTION CHECK (Page 21).
(1308) 17 of 22
REMOTE ENGINE STARTER REGISTRATION
1. Acquire the PCM Code from the Interactive Network.
2. Connect the HDS tester to the OBD II data link connector, then turn the ignition switch to the ON (II) position.
3. Start the HDS, and click the car icon.
4. Input the VIN and other required information into the HDS, then click the check button.
792901AH
CAR ICON
752502AS
Input the VIN and other required information. CHECK BUTTON
18 of 22 BII 50164
5. Select Honda Systems, then click the check button.
6. Select R/C ENG STARTER and click the check button.
752503AS
Select “Honda Systems.” CHECK BUTTON
752504AS
Select “R/C ENG STARTER.” CHECK BUTTON
(1308) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
7. A REMARKS message will display. Click on the check button.
8. Select REGISTER REMOTE CONTROL ENGINE STARTER UNIT, then click the check button.
752505AS
“REMARKS” message.
CHECK BUTTON
752506AS
Select “REGISTER REMOTE CONTROL ENGINE STARTER UNIT.”
CHECK BUTTON
© 2013 American Honda Motor Co., Inc. – All Rights Reserved. BII 50164
9. The following message will display: Obtain PCM code (IMMOBILIZER PCM CODE) from iN. This vehicle’s VIN will be required to obtain the password (USA). Click on the check button.
10. Input the PCM Code, then click the check button.
NOTE: To ensure security, the PCM code (password) is changed everyday, so it is impossible to register the remote control engine starter if the dates of the PCM code acquisition and registration are different. The date of the HDS tester should also be the same.
752507AS
“Obtain PCM-code” message.
CHECK BUTTON
752509AS
Input the PCM Code.
CHECK BUTTON
(1308) 19 of 22
11. The following message will display: The registration of the Remote Control Engine Starter Unit has been completed. Click on the check button.
12. The following message will display: Check that the engine can be started by the Transmitter. Click on the check button.
13. Perform the function test on page 21, then disconnect the HDS.
752510AS
“The registration of the Remote Control Engine Starter Unit has been completed”.
CHECK BUTTON
752511AS
“Check that the engine can be started by the Transmitter”.
CHECK BUTTON
20 of 22 BII 50164 (1308) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.
FUNCTION CHECK
Operating Conditions
• Hood is closed
• Shift lever in park
• The key is out of the ignition and the key is outside the vehicle
• All doors and trunk lid closed and locked
Inspection
1. Press the command button, and then, within 1 second, press the start button on the transmitter. The engine should start if all operating conditions are met.
Does the engine start?
2. Press the command button on the transmitter and, within 1 second, press the stop button. The engine should stop.
Does the engine stop?
3. After the engine has stopped, start the engine again, and check that the engine stops after each of the following conditions:
Yes - Operation is normal.
No:• Make sure all “Operating Conditions” are met.• Check the engine starter harness connections.• Connect the HDS and check for an indicated failure.
(Refer to the appropriate service manual for details.)
Yes - Operation is normal.
No - Check the engine starter harness connections.
NOTE: After each test the driver’s door must be opened and
closed.• Move the shift lever out of the P position.
• Unlock or open the doors or the trunk lid.
• Open the hood.
• Insert the key in the ignition switch.
• Press the brake pedal.
Does the engine stop after each of these tests?
4. Check that the power windows and the moonroof do not function, and the shift lever does not move to any position but the P position when the engine is started with the transmitter.
5. Press the command button on the transmitter two times, and check the vehicle condition on the display.
6. Check the operation of the transmitter when the vehicle is 100 m to 150 m (325 to 490 ft.) away and in direct sight.
Yes - Operation is normal.
No - Check the engine starter harness connections.
© 2013 American Honda Motor Co., Inc. – All Rights Reserved. BII 50164
732904AY
DISPLAY
COMMAND BUTTON
START BUTTON
TRANSMITTER
STOP BUTTON
(1308) 21 of 22
How to Program an Additional Transmitter
1. Connect the HDS to the data link connector.
2. Start the HDS and click on the car icon.
3. Input the vehicle’s VIN and other required information.
4. Select Honda Systems.
5. Select R/C Engine Starter.
6. Select REGISTER NEW TRANSMITTER.
7. When “Ready to program the new transmitter” shows, select ENTER.
8. Press and release the Command button.
9. Press and release the Stop button.
10. Perform the function check on both transmitters.
NOTE: Only 2 remotes can be stored in the system’s memory.
22 of 22 BII 50164
(1308) © 2013 American Honda Motor Co., Inc. – All Rights Reserved.