installation 201 instructions 2-door 2014 · © 2014 american honda motor co., inc. – all rights...

Publications No.

INSTALLATIONINSTRUCTIONS

Accessory Application

© 2014 American Honda Motor Co., Inc. – All Rights Res

VERSION 1
FOG LIGHTS
erved. AII 52270 (1409)

2015 CIVIC2-DOOR

08V31-TS8-1000-

Issue Date

SEPT 2014

PARTS LISTFog Light KitP/N 08V31-TS8-100E (non-auto light/non-BSM)P/N 08V31-TS8-100F (non-auto light/BSM)P/N 08V31-TS8-100G (auto light/non-BSM)P/N 08V31-TS8-100H (auto light/BSM)

Right fog light

Left fog light

Right fog light trim

Left fog light trim

Switch harness

Fog light harness

Combination light switch

6 Self-tapping screws, 5 x 14 mm

Relay

20A Fuse (May not used)

Fuse label (May not used)

Clip A

9 Wire ties

2 Aluminum tapes

Relay bracket

Clip B

1 of 1992

Wire tie with clip

Right fog light cover

Left fog light cover

TOOLS AND SUPPLIES REQUIRED

Phillips screwdriverDiagonal cutters10 mm SocketIsopropyl alcoholShop towelTape RatchetScissorsSmall flat-tip screwdriverBlanketThe following tool is available through the Honda Tool and Equipment Program. On the iN, click on: Service > Service Bay > Tool and Equipment Program, then enter the number under “Search”. Or, call 888-424-6857.• Plastic Trim Tool (T/N SILTRIMTL10)

Illustration of the Fog Lights Installed in the Vehicle

QC70101AT

RIGHT FOG LIGHT

LEFT FOG LIGHT

FOG LIGHT HARNESS

COMBINATION LIGHT SWITCH

SWITCH HARNESS

2 of 19 AII 52270 (14

INSTALLATION

1. Disconnect the negative cable from the battery.

2. Remove the trunk lid/fuel fill door opener cover (four retaining tabs and two hooks). Remove one self-tapping screw. Using the key, unlock the trunk opener.

Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”

Q072052AK

KEY

Unlock.

TRUNK LID/FUEL FILL DOOR OPENER COVER

4 RETAINING TABS

SELF-TAPPING SCREW

2 HOOKS

09) © 2014 American Honda Motor Co., Inc. – All Rights Reserved.

3. Release the driver’s front door sill trim (seven clips, one hook, and two retaining tabs).

4. Pull away the door opening seal, and remove the driver’s kick panel (two clips).

Q090701AK

7 CLIPS

Raise.HOOK

FRONT

DRIVER’S FRONT DOOR SILL TRIM

2 RETAINING TABS

Q072050AK

DOOR OPENING SEAL(Pull away.)

CLIP

DRIVER’S KICK PANEL

CLIP

© 2014 American Honda Motor Co., Inc. – All Rights Reserved. AII 52270 (14

5. Remove the driver’s dashboard lower cover (nine clips and unplug the vehicle connector, if equipped).

6. Lower the tilt lever, and turn the steering wheel 90° counterclockwise.

7. Using a plastic trim tool, release the lock tab as shown.

Q072055AK

VEHICLE CONNECTOR(if equipped)

9 CLIPS DRIVER’S DASHBOARD LOWER COVER

Q082304BK

STEERING WHEEL

PLASTIC TRIM TOOL

UPPER COLUMN COVER

09) 3 of 19

8. Turn the steering wheel 180° clockwise.

9. Using a plastic trim tool, release the lock tab on the other side the same way.

10. Remove the upper column cover (four hooks).

Q0D1402AH

UPPER COLUMN COVER

PLASTIC TRIM TOOL

PLASTIC TRIM TOOL

Q082307AK

4 HOOKSUPPER COLUMN COVER

4 of 19 AII 52270 (14

11. Remove two self-tapping screws from the lower column cover.

12. Remove the lower column cover (one self-tapping screw).

Q082310AK

LOWER COLUMN COVER

2 SELF-TAPPING SCREWS

Q082311AK

LOWER COLUMN COVER

SELF-TAPPING SCREW


13. Remove the front bumper:• On each side, attach tape to the areas shown.• Wrap a shop towel around the hood latch.

QC61601ATTAPE FRONT

BUMPER

HEADLIGHT

HOOD LATCH(Wrap with a shop towel.)


• Remove the 4 self-tapping screws, 10 clips, and 2 bolts.

• On each side, release two retaining tabs.

QC61602BT

2 SELF-TAPPINGSCREWS(round head)

10 CLIPS

2 SELF-TAPPING SCREWS(flat head)

2 BOLTS

QC61603AT

2 RETAINING TABS

FRONT BUMPER

09) 5 of 19

• On each side, release four retaining tabs.

• With the help of an assistant, remove the front bumper (four clips). Place the front bumper on a blanket to prevent damage.

QC61604AT

4 RETAININGTABS

FRONT BUMPER

21

QC70131AT

4 CLIPS

FRONT BUMPER

HOOKHOOK

6 of 19 AII 52270 (14

14. Remove the six clips from the right front inner fender and pull back the right inner fender as shown.

15. Remove the front bumper absorber (two hooks).

Q0D1301AH

RIGHT HEADLIGHT

6 CLIPS

RIGHT INNER FENDER(Pull back.)

FRONT RIGHT TIRE

QC70102AT

2 HOOKS

BUMPER BEAM

FRONT BUMPER ABSORBER


Installing the Fog Lights

16. Remove the left bumper trim from the front bumper (10 retaining tabs and 1 clip).

17. Install the new left fog light trim to the front bumper with 10 retaining tabs and 1 clip.

QC70103BT

FRONT BUMPER

LEFT BUMPER TRIM(Discard.)

10 RETAINING TABS

CLIP

QC70129BT

10 RETAINING TABS

FRONT BUMPER

NEW LEFT FOGLIGHT TRIM CLIP

(reused)


18. Secure the left fog light to the left fog light trim with three 5 x 14 mm self-tapping screws.

19. Install the left fog light cover to the left fog light trim with one 5 x 20 mm self-tapping screw and five retaining tabs.

20. Repeat steps 16 through 19 to install the fog light trim on the right side of the vehicle.

QC70104AT

3 SELF-TAPPING SCREWS, 5 x 14 mm

LEFT FOG LIGHT TRIM

LEFT FOG LIGHT

QC70106AT

LEFT FOG LIGHT TRIM

LEFT FOG LIGHT COVER

5 RETAINING TABS

5 x 20 mmSELF-TAPPING

09) 7 of 19

Routing the Fog Light Harness

21. Get the fog light harness. Route the fog light harness under the right headlight and secure the fog light harness clips to the holes in the extension and vehicle panel as shown.

QC70107BT

DUAL EXTENSION

FOG LIGHT HARNESS CLIP

FRONT

RIGHT HEADLIGHT

FOG LIGHT HARNESS

EXTENSION

FRONT


VEHICLE PANEL

8 of 19 AII 52270 (14

22. Locate the vehicle 1-pin connector blue-taped to the vehicle harness. Remove the blue tape to free the vehicle 1-pin connector.

23. Plug the fog light harness 1-pin connector into the vehicle 1-pin connector as shown.

QB52811AH

FOG LIGHT HARNESSVEHICLE 1-PIN

CONNECTOR

BLUE TAPE

FOG LIGHT HARNESS 1-PIN CONNECTOR

FRONT


24. Remove three bolts and one clip from the washer tank. Move the washer tank out of the way in the direction shown.

25. Remove the vehicle ground bolt. Attach the fog light harness ground terminal to the vehicle ground terminal, and reinstall the vehicle ground bolt.

QB52812AH

HOOKRIGHT HEADLIGHT

3 BOLTS

WASHER TANK

CLIP

QB52813AH

FOG LIGHT HARNESS GROUND

TERMINAL

VEHICLE GROUND BOLT(reused)

VEHICLE GROUND TERMINAL


26. Reinstall the washer tank.

27. Secure the fog light harness to the vehicle harness with two wire ties. Do not secure the fog light harness to the washer tube.

QB52814AH

WASHER TANK

CLIP

QB52815AH

VEHICLE HARNESS

2 WIRE TIES

FOG LIGHT HARNESS

09) 9 of 19

28. Secure the fog light harness to the vehicle harness with two wire ties as shown. Do not secure the fog light harness to the SRS harness.

29. Under the washer tank, secure the fog light harness to the vehicle harness with one wire tie as shown. Do not secure the fog light harness to the SRS harness.

With Vehicle Harness

QB52816AHWIRE TIE

VEHICLE HARNESS

Do not secure to the SRS harness.FOG LIGHT

HARNESS

WIRE TIE

WASHER TANK

Do notsecure tothe SRSharness.

QB52817AH

FOG LIGHT HARNESS

RIGHT HEADLIGHT

FOG LIGHT HARNESS

Do not secure to the SRS harness.

WIRE TIE

VEHICLE HARNESS

WASHER TANK

10 of 19 AII 52270 (14

30. Using diagonal cutters, cut the clip portion off of one wire tie with clip.

31. Secure the fog light harness to the vehicle harness with one wire tie with clip.Go to step 33.

QC70108CT

DIAGONAL CUTTERS

VEHICLECLIP

WIRE TIEWITH CLIP

FOG LIGHT HARNESS VEHICLE

HARNESS

Cut off. Do notsecure tothe SRSharness.


Without Vehicle Harness

32. Attach one wire tie with clip on the fog light harness and secure the fog light harness to the hole in the vehicle panel with the clip.

33. Route the fog light harness along the bumper beam as shown.

QC70109CT

VEHICLEHOLE

VEHICLE HARNESS

Do not secure to the SRS harness.

WIRE TIEWITH CLIP

FOG LIGHTHARNESS

FOG LIGHTHARNESS

QC70110AT

BUMPER BEAM FOG LIGHT

HARNESS


34. Secure the fog light harness clip to the hole in the extension as shown.

35. Using isopropyl alcohol on a shop towel, clean the bumper beam where the aluminum tapes will attach.

36. Using scissors, cut two aluminum tapes in half.37. Secure the fog light harness to the bumper beam

with the four pieces of aluminum tape in the areas shown.

QC70111AT

FRONT


DUAL EXTENSION

EXTENSION

QC70112AT

2 ALUMINUM TAPES(Cut.)

Clean with isopropyl alcohol.

BUMPER BEAM

4 ALUMINUM TAPES

09) 11 of 19

38. Reinstall the front bumper absorber.

39. Plug the fog light harness 2-pin connector into each fog light, and with the help of an assistant, reinstall the front bumper.

QC70113AT

BUMPER BEAMFRONT BUMPER

ABSORBER

QC70114AT

FOG LIGHT HARNESS 2-PIN CONNECTOR

FRONT BUMPERLEFT FOG LIGHT

RIGHT FOG LIGHT

FOG LIGHTHARNESS2-PINCONNECTOR

12 of 19 AII 52270 (14

Routing the Switch Harness

40. Remove the clip holding the vehicle harness connectors to the vehicle panel.

41. Remove the vehicle harness connector from the vehicle harness 14-pin connector.Without another accessory connector

QC70115AT

CLIP

VEHICLE HARNESS CONNECTORS

HOOD OPENER

VEHICLE PANEL

QC70116AT

VEHICLE HARNESS 14-PIN CONNECTOR

VEHICLE HARNESS CONNECTOR

FRONT


With another accessory connector

42. Remove the clip from the vehicle harness 14-pin connector, and install clip B on the vehicle harness 14-pin connector.

QC70117AT


VEHICLE HARNESS CONNECTOR

ANOTHER ACCESSORY CONNECTORS

QC70118AT

FRONT


CLIP(Discard.)

CLIP B(supplied)


43. Unplug the vehicle harness 14-pin connector.

44. Release the retainer on the vehicle harness 14-pin connector. Connect the switch harness terminal into the vehicle harness 14-pin connector in the slot shown.

45. Replug the vehicle harness 14-pin connector and reinstall the 14-pin to its original position.

QC70119AT


QC70120AT

RETAINER


HARNESS SIDE VIEW

2 RETAINING TABS(Release.)

CONNECTING LOCATION

SWITCH HARNESS TERMINAL

RETAINER

09) 13 of 19

46. Remove the vehicle bolt from the hood opener.

47. Attach the relay bracket in the position shown, and reinstall the vehicle bolt.

48. Install clip A to the relay block of the switch harness.

QC70121AT

HOOD OPENER

VEHICLE BOLT(reused)

RELAY BRACKET

Align.

HOOD OPENER

Q080206AH

RELAY BLOCK

SWITCH HARNESS

CLIP A

14 of 19 AII 52270 (14

49. Install the relay to the switch harness relay block.

50. Secure the switch harness relay block to the relay bracket.

Q080207AH

RELAY

RELAY BLOCK

SWITCH HARNESS

QC70122AT

RELAY BRACKET

RELAY BLOCK(with clip A)

SWITCH HARNESS


51. Plug the switch harness 4-pin connector and 6-pin connector into the fuse box. Go to step 54.

With Another Accessory Harness Connector

52. If the 6-pin connector is already used by another accessory, locate the 6-pin connector taped on another accessory harness. Remove the dummy connector from another accessory harness. Plug the switch harness 6-pin connector into another accessory harness 6-pin connector. Go to step 54.

Q080209AH

4-PIN CONNECTOR FUSE

BOX

4-PIN CONNECTOR

6-PIN CONNECTOR

SWITCH HARNESS

6-PIN CONNECTOR

Q0D1310AH

4-PIN CONNECTOR 6-PIN

CONNECTOR

DUMMY CONNECTOR(Discard.)

4-PIN CONNECTOR

SWITCH HARNESS

ANOTHER ACCESSORY HARNESS 6-PIN CONNECTOR


53. If the 4-pin connector is already used by another accessory, locate the 4-pin connector taped on another accessory harness. Plug the switch harness 4-pin connector into another accessory harness 4-pin connector.

54. Secure the switch harness to the vehicle harness with two wire ties.

Q0D1309AH

4-PIN CONNECTOR

SWITCH HARNESS 6-PIN

CONNECTOR

6-PIN CONNECTOR

ANOTHER ACCESSORY HARNESS 4-PIN CONNECTOR

QC70123ATVEHICLE HARNESS

2 WIRE TIES

SWITCH HARNESS

HOOD OPENER

09) 15 of 19

55. Secure the switch harness to the vehicle harness with two wire ties.

56. Unplug the vehicle connector from the combination light switch.

57. While pushing the two retaining tabs, slide the combination light switch out and remove it from the steering column. NOTE: Do not pull on the lever when removing the switch.

Q080211AH

2 WIRE TIES

VEHICLE HARNESS

SWITCH HARNESS

Q080212CH

COMBINATION LIGHT SWITCH(Discard.)

2 RETAINING TABS(Push.)

VEHICLE CONNECTOR

STEERING COLUMN STEERING WHEEL

Do not pull on the lever.

16 of 19 AII 52270 (14

58. Install the new combination light switch to the steering column. NOTE: Do not push on the lever when installing the switch.

59. Plug the vehicle connector to the new combination light switch.

If a fuse is already installed in the fuse box: go to step 63, otherwise continue with step 60.

60. Plug the 20A fuse into the fuse box.

Q080213CH

NEW COMBINATION LIGHT SWITCH

VEHICLE CONNECTOR

STEERING COLUMN STEERING WHEEL

2 RETAINING TABS(Push.)

Do not push on the lever.

Q0D1311AH

FUSE BOX

CONNECTING LOCATION

20A FUSE


61. Using isopropyl alcohol on a shop towel, clean the driver’s kick panel where the fuse label will attach.

62. Attach the fuse label to the driver’s kick panel.

63. Check that all wire harnesses are routed properly and all connectors are plugged in.

64. Reinstall all removed parts.65. Reconnect the negative cable to the battery and

check operation of all lights and other electrical accessories.

66. Press and hold the radio power button for two seconds to restore radio and navi (if equipped) system functions.

67. Reset the clock.68. Restore the systems back to normal operation as

described in the Service Manual if necessary.

Q0D1312AH

Clean with isopropyl alcohol.

FUSE LABEL(20A OPTION FUSE)

ATTACHING LOCATION

DRIVER’S KICK PANEL


USE AND CARE

How to Operate the Fog Lights

• Turn the headlight switch to the “ ” position (headlights on low beam).

• Turn the fog light switch on (indicator is on).

NOTE: The fog light lenses can cloud when the outside temperature is cold; this is normal and should go away in warm weather.• If the fog lights do not turn on, check the fuse and all the

connectors, including the ground cable.

Q0D2101AH

FOG

LIG

HT

SWIT

CH

HEADLIGHT SWITCH

Low HighOFF

OFF -

ON

- - -

- - -

The auto light model is shown.

09) 17 of 19

Fog Light Aiming Adjustment

69. Adjust the fog light:• Adjust the aim according to your local laws and

regulations.• To adjust, turn the adjustment screw in or out

until the correct aim is obtained.

BULB REPLACEMENT1. Remove the fog light cover (one 5 x 20 mm self-

tapping screw and five retaining tabs).

QC70124AT

AIMING ADJUSTMENT SCREW

To lower. To raise.

AIMING ADJUSTMENT SCREW

FOG LIGHT

QC70106AT

SELF-TAPPING SCREW, 5 x 20 mm

FOG LIGHT TRIM

FOG LIGHT COVER

5 RETAINING TABS

18 of 19 AII 52270 (14

2. Remove the fog light (three self-tapping screws and unplug the vehicle connector).

3. Remove the bulb from the fog light as shown.

QC70125AT

RETAINING TAB(Push.)

Pull.VEHICLE CONNECTOR

3 SELF-TAPPING SCREWSFOG LIGHT

QC70126AT

BULB(Turn.)

FOG LIGHT


4. Install the new bulb to the fog light.• Use only a genuine Honda halogen light bulb of

specified wattage. Rating: 12V 55W H11 Halogen Light Bulb P/N 33165-S5A-003

• Do not touch the bulb. Oily or greasy substances on the bulb can shorten its service life due to the heat produced when the bulb is turned on. If the bulb is accidentally touched, wipe it clean with a soft cloth that has been dampened with a denatured alcohol or a mild detergent solution.

• When installing the new bulb, align the cutout on the fog light with the tab on the new bulb and turn the new bulb in completely. If not properly aligned, the fog light may annoy the oncoming driver’s view.

5. Reinstall the fog light.

QC70127AT

Turn the bulb until it stops.

FOG LIGHT

NEW BULB

NEW BULB


• Check that the wire harness is not pinched.• Be sure to tighten the self-tapping screws

securely.

6. Install the fog light cover to the fog light trim with one 5 x 20 mm self-tapping screw and five retaining tabs.

7. Check the operation of the fog light; readjust the aim if necessary.

QC70128AT

VEHICLE CONNECTOR

FOG LIGHT3 SELF-TAPPING SCREWS

QC70106AT

5 x 20 mmSELF-TAPPING SCREW

FOG LIGHT TRIM

FOG LIGHTCOVER

5 RETAINING TABS

09) 19 of 19

installation 201 instructions 2-door 2014 · © 2014 american honda motor co., inc. – all rights...

Documents