inflatable boats...inflatable boats — part 4: boats with a hull length of between 8 m and 24 m...

Reference numberISO 6185-4:2011(E)

© ISO 2011

INTERNATIONAL STANDARD

ISO6185-4

First edition2011-07-01

Inflatable boats — Part 4: Boats with a hull length of between 8 m and 24 m with a motor power rating of 15 kW and greater

Bateaux pneumatiques —

Partie 4: Bateaux d'une longueur de coque comprise entre 8 m et 24 m et d'une puissance moteur nominale supérieure ou égale à 15 kW

This is a preview of "ISO 6185-4:2011". Click here to purchase the full version from the ANSI store.This is a preview of "ISO 6185-4:2011". Click here to purchase the full version from the ANSI store.This is a preview of "ISO 6185-4:2011". Click here to purchase the full version from the ANSI store.This is a preview of "ISO 6185-4:2011". Click here to purchase the full version from the ANSI store.

http://webstore.ansi.org/RecordDetail.aspx?sku=ISO%206185-4:2011&source=preview

https://webstore.ansi.org/RecordDetail.aspx?sku=ISO%206185-4:2011&source=preview

https://webstore.ansi.org/Standards/ISO/ISO61852011&source=preview

https://webstore.ansi.org/Standards/ISO/ISO61852011?source=preview

ISO 6185-4:2011(E)

COPYRIGHT PROTECTED DOCUMENT © ISO 2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester.

ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org

Published in Switzerland

ii © ISO 2011 – All rights reserved






ISO 6185-4:2011(E)

© ISO 2011 – All rights reserved iii

Contents Page

Foreword .............................................................................................................................................................v Introduction........................................................................................................................................................vi 1 Scope ......................................................................................................................................................1 2 Normative references............................................................................................................................1 3 Terms and definitions ...........................................................................................................................3 4 Symbols..................................................................................................................................................4 5 Materials .................................................................................................................................................5 5.1 General ...................................................................................................................................................5 5.2 Materials making up the buoyancy tube .............................................................................................5 5.3 Wood.......................................................................................................................................................7 5.4 Metal parts..............................................................................................................................................7 5.5 Glass-reinforced plastics......................................................................................................................8 5.6 Other materials ......................................................................................................................................8 5.7 Buoyant material used in foam-filled buoyancy tubes......................................................................8 6 Functional components ........................................................................................................................9 6.1 Conditioning ..........................................................................................................................................9 6.2 Buoyancy tube and hull fittings (items bonded to the buoyancy tube) ..........................................9 6.3 Valves (if applicable) ...........................................................................................................................10 6.4 Transom................................................................................................................................................10 6.5 Hull interior drainage ..........................................................................................................................10 6.6 Remote steering system (where offered as standard or optional equipment) .............................10 6.7 Towing, anchoring and mooring strong points................................................................................11 6.8 Seating and attachment systems (where offered as standard or optional equipment)...............11 6.9 Electrical installations (where offered as standard or optional equipment) .................................11 6.10 Engine and engine spaces .................................................................................................................11 6.11 Ventilation of petrol motor and petrol tank compartments (where applicable) ............................11 6.12 Devices for lifting the boat (if applicable) .........................................................................................12 6.13 Fire protection (if applicable) .............................................................................................................12 6.14 Openings in hull, deck or superstructure .........................................................................................12 6.15 Gas systems ........................................................................................................................................12 6.16 Navigation lights..................................................................................................................................12 6.17 Discharge prevention..........................................................................................................................12 6.18 Noise emissions (applicable to inboard engines installations without integral exhaust)...........12 7 Safety requirements of the completed boat .....................................................................................12 7.1 Maximum permissible number of persons (crew limit) ...................................................................12 7.2 Motor power calculation .....................................................................................................................13 7.3 Maximal manoeuvring speed (if applicable) .....................................................................................13 7.4 Static stability of the boat...................................................................................................................16 7.5 Maximum load capacity ......................................................................................................................17 7.6 Buoyancy requirements......................................................................................................................17 7.7 Compartmentation (inflatable buoyancy tubes)...............................................................................18 7.8 Nominal pressures (inflatable buoyancy tubes) ..............................................................................18 7.9 Strength of the inflatable buoyancy tube..........................................................................................18 7.10 Man overboard prevention and recovery..........................................................................................19 7.11 Field of vision from the helm position ..............................................................................................19 7.12 Provision for a liferaft or liferafts.......................................................................................................19 7.13 Self-bailing ...........................................................................................................................................19 7.14 Buoyancy tube attachment strength test (type test only)...............................................................20






ISO 6185-4:2011(E)

iv © ISO 2011 – All rights reserved

7.15 Strength of the rigid structure (type test only) .................................................................................22 7.16 Strength of principal factory-fitted accessories...............................................................................22 8 Builder's plate(s) ..................................................................................................................................24 9 Owner's manual ...................................................................................................................................24 10 Standard equipment ............................................................................................................................25 Annex A (informative) Typical Type IX powered boat ...................................................................................26 Annex B (informative) Typical Type X powered boat ....................................................................................28 Bibliography ......................................................................................................................................................29






ISO 6185-4:2011(E)

© ISO 2011 – All rights reserved v

Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.

ISO 6185-4 was prepared by Technical Committee ISO/TC 188, Small craft.

This first edition, together with ISO 6185-1, ISO 6185-2 and ISO 6185-3, cancels and replaces ISO 6185:1982, which has been technically revised.

ISO 6185 consists of the following parts, under the general title Inflatable boats:

⎯ Part 1: Boats with a maximum motor power rating of 4,5 kW

⎯ Part 2: Boats with a maximum motor power rating of 4,5 kW to 15 kW inclusive

⎯ Part 3: Boats with a maximum motor power rating of 15 kW and greater

⎯ Part 4: Boats with a hull length of between 8 m and 24 m with a motor power rating of 15 kW and greater






ISO 6185-4:2011(E)

vi © ISO 2011 – All rights reserved

Introduction

ISO 6185 is subdivided into four parts as shown in Figure 1.

It excludes

a) single-chamber boats,

b) boats of less than 1 800 N buoyancy, and

c) boats made from unsupported materials of more than 12 kN inflated buoyancy and powered by motors of power P > 4,5 kW.

It is not applicable to aquatic toys, nor to inflatable liferafts which are specified in ISO 9650.

ISO 6185-1:

⎯ Type I Boats with LH < 8 m propelled exclusively by manual means.

⎯ Type II Powered boats with LH < 8 m with a power P ≤ 4,5 kW.

⎯ Type III Canoes and kayaks with LH < 8 m.

⎯ Type IV Sail boats with LH < 8 m with a sail area less than or equal to 6 m2.

ISO 6185-2:

⎯ Type V Powered boats with LH < 8 m with a power 4,5 kW < P ≤ 15 kW.

⎯ Type VI Sail boats with LH < 8 m with a sail area greater than 6 m2.

ISO 6185-3:

⎯ Type Vll Powered boats with LH < 8 m with a power P ≥ 15 kW.

⎯ Type Vlll Powered boats with LH < 8 m with a power P ≥ 75 kW.

ISO 6185-4:

⎯ Type IX Powered boats (design categories C and D) with 8 m < LH ≤ 24 m with power P ≥ 15 kW.

⎯ Type X Powered boats (design category B) with 8 m < LH ≤ 24 m with power P ≥ 75 kW.






ISO 6185-4:2011(E)

© ISO 2011 – All rights reserved vii

Figure 1 — Illustration of how ISO 6185 is subdivided

This part of ISO 6185 enables the boat to be assigned to a design category appropriate to its design and maximum load. The categories used align with those in the Recreational Craft Directive of the European Union, EU Directive 94/25/EC as amended by Directive 2003/44/EC.






inflatable boats...inflatable boats — part 4: boats with a hull length of between 8 m and 24 m...

Documents