in00272 (rev b) telescopic pivot door & side panel · a a b* 8-15mm** a * dimension b =...

IMPORTANT: If installing a Telescopic Pivot Door only; ie. a recess installation, please refer to alternative fixing details on the document reverse.

IN00272 (rev B)

Telescopic Pivot Door & Side PanelInstruction suitable for both Right and Left Hand fixing variations.•

Help Line: 0870 241 6131

Check that the tray has been installed correctly • and that it is level (Fig. A), tiled down onto and sealed to the manufacturer’s guidelines. Please Note: All product supplied without tray.Ensure the product is fitted to a non-porous • surface ie. tiled. Check that the wall surface is flat.Unpack and check the product is complete and • undamaged.Fixings are supplied for solid walls only. Ensure • that the correct fixings are used for the wall type – if in doubt seek professional advice.Ensure the area is clean, dry and dust free.• Read the instructions in full.• Have the correct tools available, (as shown • below, see ‘Tools Required’).It is recommended to situate the showerhead • and door adjacent to each other in order to allow any water spray to be on the side panel or upstanding wall.

Handle all glass with care - support on cardboard to avoid risk of breakage.• This product is heavy and requires 2 people to carry and install it.• When drilling walls check first for hidden pipes and cables.• All glass is toughened – it cannot be reworked or replaced by ordinary glass.• Use safety eyewear when drilling.• Use safety eyewear when handling glass.• Keep all small parts away from children.•

Safety

Please notify the retailer immediately of any damage or faults. The manufacturer cannot be held • responsible for any installation costs that may arise from damaged or faulty product being installed.Please dispose of all packaging with due regard to the environment.•

Disclaimer

Before You Start

Tools Required (not supplied)

Fig.A.

Spirit Level Screwdriver Tape Measure

Junior Hacksaw

Pencil Utility Knife

Silicone Gun & Sealant Power Drill Suitable Drill Bits

6mm dia. *

3mm dia. HSS

* Ensure drill bit used is suitable for wall surface

Lines open: 8.30am - 5.00pm Monday to FridayStandard National call charge rate from BT landlines

Side PanelX1

Telescopic Pivot Door

X1

Short Horizontal Door SealX1

Horizontal Door Seal

X1

Parts & Fittings Supplied

Please notify the retailer immediately of any damage or faults. The manufacturer cannot be held responsible for any installation costs that may arise from a damaged or faulty product being installed.

!Keep small parts away from children!

D1

D2

D3

D4

B

D

C

Wall Channel X2

Door Handle Assembly

X1

A

D

D

C

E

D2D1

D4D3

No.8 x 1¾” Pan Head Pozi Screws (actual size)

(actual size)

(actual size)

(actual size)

Ax6

Qty

Wall PlugsBx6

Qty

No.8 x ⅜” Pan Head Pozi ScrewsCx9

Qty

Screw Snap CapDx15

Qty

(actual size)

Ex4

Qty

Loose Screws & Fittings Supplied

A

A

1

Position Wall Channel onto Side Panel, DO NOT FIX at this stage.!

Position Side Panel and mark as shown. Ensure Side Panel is level.!

Make a note of Dimension A (from Wall Channel to edge of Tray).!

Ensure glass is positioned straight and is parallel with tray. !Mark Side Panel positions as shown.!

Plan View

AA

B*

8-15mm**A

* Dimension B = Telescopic Door width

** 8-15mm to be left for adjustment

Position Wall Channel onto Telescopic Pivot Door, DO NOT FIX at this stage.

!

2 Position Telescopic Pivot Door and mark as shown. Ensure Telescopic Pivot Door is level.

!

Plan ViewIMPORTANT NOTE:Ensure that Wall Channel is positioned to match dimension A, as taken in previous step (1).

!

Mark Telescopic Pivot Door position as shown.!

Ensure glass is positioned straight and is parallel with tray. !

3

3.1

6mm dia. holes with drill bit suitable for wall surface

Mark position of pre-drilled Wall Channel fixing hole

A

3.2

3.3B

D

Fix through pre-drilled Wall Channel fixing hole

Wall plugs supplied are for solid walls only. Ensure correct wall plug for wall type is used. If in doubt seek professional advice.

!Position Wall Channel on wall as shown, ensure Wall Channel is fixed level. !

Tip: When drilling tiles apply masking tape to surface to stop drill bit slipping.*

Inside View

E

4.3*4.4

* 3mm dia. holes through pre-drilled holes using HSS drill bit

4.2

4.1

Mark adjustment position.

Adjust Telescopic Pivot Door to match dimension B,

(as taken in step 2).

4

Ensure same dimension (B) at the top and bottom of Telescopic Pivot Door.!Take Care to ensure that Telescopic pivot Door is fixed straight and not twisted.!

5.1

! INSIDE

Please Note: Ensure deflector faces inwards.

5.2

5.3 Plan View

Ensure glass is positioned straight and is parallel with tray. !

Push fit Horizontal Seals.!

7


*3mm dia. holes through pre-drilled holes using

HSS drill bit

C

D

Inside ViewInside View

C

6.1*

6.2

Tip: When inserting screws apply a small amount of oil to the screw thread to allow easier fixing.

* Ensure glass is positioned straight and is parallel with tray. !

D


*Ensure glass is positioned straight and is parallel with tray. !


7.1*

7.2

6

8.1

8

Please Note: Door Handles are supplied assembled. Using Allen key supplied, disassemble part and then re-assemble as shown. Ensure all screw heads are on the enclosure interior. DO NOT overtighten.

!

Inside View

150mm

150mm

150mm

Apply Silicone Sealant, (not supplied).!Only apply silicone sealant to the outside of the enclosure. DO NOT use silicone sealant on inside of the enclosure.

!Product Care: Use a non-abrasive cleaner. Water marks may be removed with a proprietary limescale remover or household vinegar.

*

9

IMPORTANT: If installing a Telescopic Pivot Door and Side Panel; ie. a corner installation, please refer to alternative fixing details on the document reverse.

IN00272 (rev B)

Telescopic Pivot DoorInstruction suitable for both Right and Left Hand fixing variations.•

Help Line: 0870 241 6131

Check that the tray has been installed correctly • and that it is level (Fig. A), tiled down onto and sealed to the manufacturer’s guidelines. Please Note: All product supplied without tray.Ensure the product is fitted to a non-porous • surface ie. tiled. Check that the wall surface is flat.Unpack and check the product is complete and • undamaged.Fixings are supplied for solid walls only. Ensure • that the correct fixings are used for the wall type – if in doubt seek professional advice.Ensure the area is clean, dry and dust free.• Read the instructions in full.• Have the correct tools available, (as shown • below, see ‘Tools Required’).It is recommended to situate the showerhead • and door adjacent to each other in order to allow any water spray to be on the side panel or upstanding wall.

Handle all glass with care - support on cardboard to avoid risk of breakage.• This product is heavy and requires 2 people to carry and install it.• When drilling walls check first for hidden pipes and cables.• All glass is toughened – it cannot be reworked or replaced by ordinary glass.• Use safety eyewear when drilling.• Use safety eyewear when handling glass.• Keep all small parts away from children.•

Safety

Please notify the retailer immediately of any damage or faults. The manufacturer cannot be held • responsible for any installation costs that may arise from damaged or faulty product being installed.Please dispose of all packaging with due regard to the environment.•

Disclaimer

Before You Start

Tools Required (not supplied)

Fig.A.

Spirit Level Screwdriver Tape Measure

Junior Hacksaw

Pencil Utility Knife

Silicone Gun & Sealant Power Drill Suitable Drill Bits

6mm dia. *

3mm dia. HSS

* Ensure drill bit used is suitable for wall surface

Lines open: 8.30am - 5.00pm Monday to FridayStandard National call charge rate from BT landlines

Short Horizontal Door Seal

X1

Horizontal Door Seal

X1

Telescopic Pivot Door

X1

Parts & Fittings Supplied

Please notify the retailer immediately of any damage or faults. The manufacturer cannot be held responsible for any installation costs that may arise from a damaged or faulty product being installed.

!Keep small parts away from children!

D3

D1

D2

Door Handle Assembly

X1

B

D

A

Wall Channel X2

C

D

E

D2D1

D3

No.8 x 1¾” Pan Head Pozi Screws (actual size)

(actual size)

(actual size)

(actual size)

Ax6

Qty

Wall PlugsBx6

Qty

No.8 x ⅜” Pan Head Pozi ScrewsCx6

Qty

Screw Snap CapDx12

Qty

(actual size)

Ex4

Qty

Dimension A* - (minus) 20mm = Telescopic Pivot Door Width (B)

*Between walls, recess dimension.

1Make a note of Dimension A* (from recess opening).!

Loose Screws & Fittings Supplied

***Telescopic Pivot Door width: Refer to Step 1 for details.

E

2.3*2.4


2.2

2.1

Mark adjustment position.

Adjust Telescopic Pivot Door to match dimension B,

(as taken in step 1).

2

Ensure same dimension (A) at the top and bottom of Telescopic Pivot Door.!Take Care to ensure that Telescopic pivot Door is fixed straight and not twisted.!

! INSIDE

Please Note: Ensure deflector faces inwards.

Please Note: Position one wall channel and mark. Ensure Wall Channel is level and in correct location to the tray. (If in doubt refer to illustration on step 2).

!3.1

3.2

3.3 3.4

IMPORTANT: Ensure Door is not twisted. For best results fix one side wall channel, and check door is level before continuing to fix second wall channel.

!

Position Wall Channel on wall as shown, ensure Wall Channel is fixed level. !Wall plugs supplied are for solid walls only. Ensure correct wall plug for wall type is used. If in doubt seek professional advice.

!Tip: When drilling tiles apply masking tape to surface to stop drill bit slipping.*

4.1

6mm dia. holes with drill bit suitable for wall surface

Mark position of pre-drilled Wall Channel fixing hole

4.2

4.3

4

Fix through pre-drilled Wall Channel fixing hole

A

B

D

Ensure glass is positioned straight and is parallel with tray. ! Inside View

Plan View

6

5*3mm dia. holes through pre-drilled holes using

HSS drill bit

C

D


*


5.1*

5.2

6.1

Please Note: Door Handles are supplied assembled. Using Allen key supplied, disassemble part and then re-assemble as shown. Ensure all screw heads are on the enclosure interior. DO NOT overtighten.

!

Inside View

150mm

7

Apply Silicone Sealant, (not supplied).!Only apply silicone sealant to the outside of the enclosure. DO NOT use silicone sealant on inside of the enclosure.

!Product Care: Use a non-abrasive cleaner. Water marks may be removed with a proprietary limescale remover or household vinegar.

*

Notes:Notes:

in00272 (rev b) telescopic pivot door & side panel · a a b* 8-15mm** a * dimension b =...

Documents