illustrated tool and equipment - hartzellprop.com · illustrated tool and equipment manual hartzell...

Illustrated

Tool and EquipmentManual

Hartzell Propeller Inc.One Propeller PlacePiqua, Ohio 45356-2634 U.S.A.Phone: 937.778.4200Fax: 937.778.4215

Manual No. 165A61-00-65Revision 25September 2019

COVER 61-00-65 Inside CoverRev. 25 Sep/19

TOOL AND EQUIPMENT MANUAL165A

(This page is intentionally blank.)

© 1995, 1996, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2011, 2012, 2013, 2014, 2016, 2017, 2018, 2019 - Hartzell Propeller Inc. - All rights reserved


REVISION HIGHLIGHTS 61-00-65 Page 1Rev. 25 Sep/19

REVISION 25 HIGHLIGHTS

Revision 25, dated September 2019, incorporates the following:

Front matter (Cover, Revision Highlights, etc.), has been revised to match this revision.

Minor language/format changes and renumbering, if applicable are marked with a revision bar, but are not listed below.

• NUMERICAL INDEX • Removedthissection

• TOOL AND EQUIPMENT INDEX • Revisedtomatchthemanualrevision

• ALPHABETICAL INDEX • Removedthissection

• TOOL AND EQUIPMENT LIST • Revisedthesection,"Y"ShankEddyCurrentProbeandEddyCurrentTestShank" • Revisedthesection,"TorqueWrenchAdapter" • Revisedthesection,"Profilometer" • Revisedthesection,"SpringCompressorBase" • Revisedthesection,"SpringCompressorRetainer" • Revisedthesection,"BuildingBuckComponents" • Revisedthesection,"PilotTubeInstallationToolKit" • Revisedthesection,"PropellerAssemblyTable" • Revisedthesection,"ThreadGaugeAirflowKit" • Revisedthesection,"UltrasonicFlawDetectorKit" • Revisedthesection,"EddyCurrentTestInstrument" • Revisedthesection,"UltrasonicFlawDetector"



(Thispageisintentionallyblank.)



REVISION 25 HIGHLIGHTS

1. Introduction

A. General

(1) This is a list of current revisions that have been issued against this manual. Please compare to the RECORD OF REVISIONS page to make sure that all revisions have been added to the manual.

B. Components

(1) Revision No. indicates the revisions incorporated in this manual.

(2) Issue Date is the date of the revision.

(3) Comments indicates the level of the revision.

(a) New Issue is a new manual distribution. The manual is distributed in its entirety.Alltherevisiondatesarethesameandnochangebarsareused.

(b) Reissue is a revision to an existing manual that includes major content and/ormajorformatchanges.Themanualisdistributedinitsentirety.Allthe revision dates are the same and no change bars are used.

(c) Major Revision is a revision to an existing manual that includes major content or minor format changes over a large portion of the manual. The manualisdistributedinitsentirety.Alltherevisiondatesarethesame,butchange bars are used to indicate the changes incorporated in the latest revision of the manual.



(d) Minor Revision is a revision to an existing manual that includes minor contentchangestothemanual.Onlytherevisedpagesofthemanualaredistributed. Each page retains the date and the change bars associated with the last revision to that page.

Revision No. Issue Date Comments

Original Nov/95 Total rewrite Revision 1 Aug/96 Minor Revision Revision2 May/98 MinorRevision Revision 3 Jan/99 Minor Revision Revision 4 Oct/99 Minor Revision Revision 5 Apr/00 Minor Revision Revision6 May/01 MinorRevision Revision 7 Aug/01 Minor Revision Revision8 Mar/02 MinorRevision Revision 9 Jun/02 Minor Revision Revision 10 Sep/03 Minor Revision Revision 11 Aug/04 Minor Revision Revision 12 Aug/11 Major Revision Revision 13 Jul/12 Minor Revision Revision 14 Jun/13 Minor Revision Revision 15 Dec/13 Minor Revision Revision 16 Apr/14 Minor Revision Revision 17 Dec/14 Minor Revision Revision18 Feb/16 MinorRevision Revision 19 Nov/16 Minor Revision Revision 20 Apr/17 Minor Revision Revision 21 Oct/17 Minor Revision Revision22 Mar/18 MinorRevision Revision 23 Feb/19 Minor Revision Revision 24 Apr/19 Minor Revision Revision 25 Sep/19 Minor Revision

RECORD OF REVISIONS

This is a permanent historical record of revisions inserted into this manual.Revision 12 includes all prior revisions, up to and including Revision 11.

TOOL AND EQUIPMENT MANUAL 165A

RECORD OF REVISIONSPage 1

Rev. 12 Aug/1161-00-65

Revision Number

Issue Date

Date Inserted

Inserted By

12 Aug/11 Aug/11 HPI

13 Jul/12 Jul/12 HPI

14 Jun/13 Jun/13 HPI

15 Dec/13 Dec/13 HPI

16 Apr/14 Apr/14 HPI

17 Dec/14 Dec/14 HPI

18 Feb/16 Feb/16 HPI

19 Nov/16 Nov/16 HPI


21 Oct/17 Oct/17 HPI

22 Mar/18 Mar/18 HPI

23 Feb/19 Feb/19 HPI


25 Sep/19 Sep/19 HPI

Revision Number

Issue Date

Date Inserted

Inserted By


Page 2Rev. 12 Aug/1161-00-65RECORD OF REVISIONS

RECORD OF REVISIONS

This is a permanent historical record of revisions inserted into this manual. Revision 12 includes all prior revisions, up to and including Revision 11.

Revision Number

Issue Date

Date Inserted

Inserted By

Revision Number

Issue Date

Date Inserted

Inserted By

RECORD OF TEMPORARY REVISIONS

Update this page to show all temporary revisions inserted into this manual. Revision 12 includes all prior temporary revisions, up to and including TR-008.


Page 1Rev. 12 Aug/1161-00-65RECORD OF TEMPORARY REVISIONS

TemporaryRevision No.

Section/Page

IssueDate

DateInserted

InsertedBy

DateRemoved

RemovedBy

TR-009 4-43 Oct/11 Oct/11 HPI Jul/12 HPI

TR-010 4-14 Nov/11 Nov/11 HPI Jul/12 HPI

TR-011 4-65 May/12 May/12 HPI Jul/12 HPI

TR-012 4-136 Oct/12 Oct/12 HPI Jun/13 HPI

TR-013 4-144 Sep/13 Sep/13 HPI Dec/13 HPI

TR-014 4-149 Mar/14 Mar/14 HPI Apr/14 HPI

TR-015 4-82 Jan/15 Jan/15 HPI Feb/16 HPI

TR-016 4-39 Mar/15 Mar/15 HPI May/15 HPI

TR-017 4-39 May/15 May/15 HPI Feb/16 HPI




TR-021 4-90 Jul/16 Jul/16 HPI Nov/16 HPI




TR-025 4-42.1 Jul/16 Jul/16 HPI Nov/16 HPI


TR-027 Intro-4 Jul/16 Jul/16 HPI Nov/16 HPI

TR-028 4-85 Feb/17 Feb/17 HPI Apr/17 HPI

TR-029 4-22 Feb/17 Feb/17 HPI Apr/17 HPI

TR-030 4-161 Jun/18 Jun/18 HPI Feb/19 HPI

TR-031 Intro-9 Jun/18 Jun/18 HPI Feb/19 HPI

TR-032 4-102 Jun/18 Jun/18 HPI Feb/19 HPI

RECORD OF TEMPORARY REVISIONS

Update this page to show all temporary revisions inserted into this manual.Revision 12 includes all prior temporary revisions, up to and including TR-008.


Page 2Rev. 12 Aug/1161-00-65RECORD OF TEMPORARY REVISIONS

TemporaryRevision No.

Section/Page

IssueDate

DateInserted

InsertedBy

DateRemoved

RemovedBy

LIST OF EFFECTIVE PAGES

Chapter Page Revision Level Date

Cover/Cover Back Cover/Inside Cover Rev. 25 Sep/19Revision Highlights 1 thru 4 Rev. 25 Sep/19Record of Revisions 1 and 2 Rev. 12 Aug/11Record of Temporary Revisions 1 and 2 Rev. 12 Aug/11List of Effective Pages 1 and 2 Rev. 25 Sep/19Table of Contents 1 and 2 Rev. 25 Sep/19Introduction 1 thru 12 Rev. 23 Feb/19Tool and Equipment Index 1-1 thru 1-14 Rev. 25 Sep/19Tool and Equipment List 2-1 thru 2-158 Rev. 25 Sep/19



Page 1Rev. 25 Pre/1961-00-65




Page 2Rev. 25 Sep/1961-00-65


TABLE OF CONTENTS 61-00-65 Page 1Rev. 25 Sep/19

TABLE OF CONTENTS

REVISION HIGHLIGHTS .................................................................................................1RECORD OF REVISIONS ...............................................................................................1RECORD OF TEMPORARY REVISIONS ........................................................................1LIST OF EFFECTIVE PAGES ..........................................................................................1TABLE OF CONTENTS ....................................................................................................1INTRODUCTION ..............................................................................................................1TOOL AND EQUIPMENT INDEX ..................................................................................1-1TOOL AND EQUIPMENT LIST ......................................................................................2-1


TABLE OF CONTENTS 61-00-65 Page 2Rev. 25 Sep/19



Page 1Rev. 23 Feb/19

INTRODUCTION 61-00-65

INTRODUCTION - CONTENTS

1. Using the Illustrated Tool and Equipment Manual .................................................3

A. General.............................................................................................................3

B. Vendor ..............................................................................................................4

C. Page ...............................................................................................................12

2. Using the “TE” Reference Number ......................................................................12

3. Ordering Parts .....................................................................................................12




INTRODUCTION

1. Using the Illustrated Tool and Equipment Manual

A. General

(1) This manual contains the tooling and equipment required to perform standard procedures in accordance with Hartzell Propeller Inc. manuals.

(2) In addition to an illustration of each item, the following information is provided:

(a) The title or description

(b) The part number

1 The part number listed should be used when ordering the item from Hartzell Propeller Inc. or a Hartzell Propeller Inc. approved distributor.

(c) The TE number

1 The number given to the tool that is used to reference the tool in Hartzell Propeller Inc. publications.

(d) A description of the item, including:

1 Its uses and other related items needed to perform the task

2 A breakdown of subcomponents, as necessary

3 Information required to fabricate the item, if applicable

4 Additional vendors where the item may be purchased, as necessary.

(3) Some of the parts may be purchased through Hartzell Propeller Inc. Refer to the specific tool for information about the Hartzell Propeller Inc. part number.

(4) Tool and Equipment Index

(a) The Tool and Equipment Index of this Tool and Equipment Manual is a list of the tools by TE number that are included in this manual and the page number on which the tool illustration and information may be found.

1 For a tool that shows more than one page number in the index, generally the first page number is where the most comprehensive information about the tool may be found. The additional page numbers given are other places in the manual where the tool is referenced.

(b) The Tool and Equipment Index of this Tool and Equipment Manual uses a number of abbreviations. Refer to the sections "Vendor" and "Application" in this chapter for a list of the abbreviations used.




B. Vendor

The vendor is the point of purchase of the item for the end user:AE All Phase Electric Supply Co ............Direct from the Vendor 750 W. Leffel Lane. Springfield, OH 45501 Tele: 937-323-7555 Fax: 937-325-0838 Email: [email protected] www. all-phase-springfield.shopced.com

AF American Forge & Foundry, Inc. .......Direct from the Vendor PO. Box 59 Guilderland Center, NY 12085 Tele: 518-861-0101 Toll Free: 800-255-0555 Fax: 518-861-0099 Email: [email protected] www.affjaxx.com

AL ALATEC Products Corp ....................Direct from the Vendor 12109 Bridgeton Square Drive Bridgeton, MO 63044

AP APEX Products .................................From any Distributor Division of Cooper Tools P.O. Box 952 Dayton, OH 45401

AR Associated Research ........................From any Distributor 905 Carriage Park Avenue Lake Bluff, IL 60044 Tele: 800-858-8378

BD ..........................................................Contact any Bearing Distributor

BG Browning. ..........................................Either through the Hartzell Propeller Inc. distributor network, or it may be purchased directly from the distributor

BH Bondhus ............................................From any Distributor 1400 East Broadway Monocello, MN 55362

BI Baty International ..............................Direct from the Vendor Baty Precision Measuring Instruments 45 Victoria Road Burgess Hill West Sussex RH15 9LR, U.K. Email: [email protected]




BK BK Precision .....................................Direct from the Vendor 3033 South Kettering Blvd. Dayton, OH 45439-1948 Tele: 937-294-8980 Fax: 937-294-2517

BN Branson Ultrasonics Corporation ......Direct from the Vendor 41 Eagle Road Danbury, CT 06813-1961 Tele: 800-732-9262 Fax: 203-796-2240

BO Bodine Electric Co. ...........................Either through the Hartzell Propeller Inc. 201 Northfield Road distributor network, or it may be purchased Northfield, IL 60093 directly from the vendor or distributor Tele: 773-478-3515 Toll Free: 800-7BODINE Fax: 773-478-3232 Outside the US: 773-478-3515 www.bodine-electric.com

BR BriskHeat Corporation .......................Direct from the Vendor or Hartzell Propeller Inc. P.O. Box 163309 Columbus, OH 43216-3309 Tele: 800-848-7673

CG Clay-Groomer Machine Shop, Inc .....Direct from the Vendor or Hartzell Propeller Inc. 701 S. Carlton Ave. Farmington, NM 87401 Tele: 505-327-7751

CL Clemco Industries Corp. ...................Direct from the Vendor One Cable Car Drive Washington, MO 63090 Tele: 636-239-8172

CP Cole Palmer ......................................Direct from the Vendor or Distributor 7425 N. Oak Park Avenue Chicago, IL 60648

CS Customer Supplied ...........................Locally fabricated by the end user. Information required to purchase or fabricate the unit will be found in the description

DE DeLong Equipment Co. .....................Either through the Hartzell Propeller Inc. 1216 Zonolite Road distributor network, or it may be purchased Atlanta, GA 30306 directly from the vendor or distributor Tele: 404-607-1234 Toll Free: 800-548-8233 Fax: 800-548-8233 www.delongequipment.com




DM Daniels Manufacturing Corp. ............Direct from the Vendor or Distributor 526 Thorpe Road Orlando, FL 32824-8133

DS DE-STA-CO ......................................Either through the Hartzell Propeller Inc. Destaco distributor network, or it may be purchased 691 North Squirrel Road directly from the vendor or distributor Suite 250 Auburn Hills, MI 48326 Tele: 248-534-1111 Toll Free: 888-DESTACO (337-8226) Toll Free Fax: 800-682-9689 Fax: 248-836-6740 www.destaco.com

EC Eaton Cutler-Hammer (Durant) .........Either through the Hartzell Propeller Inc. 1000 Cherrington Parkway distributor network, or it may be purchased Moon Township, PA 15108 directly from the vendor or distributor Tele: 412-893-3300 www.eaton.com

EK Eastman Kodak Company ................Direct from the Vendor Commercial Imaging Group 343 State Street Rochester, NY 14650, USA Tele: 585-724-4000

EL Electronics Inc. ..................................Either through the Hartzell Propeller Inc. 56790 Magnetic Dr. distributor network, or it may be purchased Mishawaka, IN USA 46545 directly from the vendor or distributor Tele: 574-256-5001 Toll Free: 800-832-5653 Fax: 574-256-5222 Email: [email protected] www.electronics-inc.com

EP Everhard Products ............................Direct from the Vendor 1016 Ninth Street, SW Canton, OH 44707 Tele: 216-453-7786

ER Ervin Industries .................................Either through the Hartzell Propeller Inc. 681 East Butler Road distributor network, or it may be purchased Butler, PA 16002 directly from the vendor or distributor Tele: 724-282-1060 www.ervinindustries.com

GO George Olcott Co. .............................Direct from the Vendor P.O. 783 Scottsboro, AL 35768 Tele: 256-259-4937 Fax: 256-259-4942




HA Hammond Manufacturing ..................Either through the Hartzell Propeller Inc. 475 Cayuga Rd distributor network, or it may be purchased Cheektowaga, New York, 14225 directly from the vendor or distributor Tele: 716-630-7030 Fax: 716-630-7042 www.hammondmfg.com

HE Heli-Coil Division ...............................Direct from the Vendor Emhart Fastening Systems Group Shelter Rock Lane Danbury, CT 06810 Tele: 203-743-7651 Fax: 203-798-2540

HM Hemco Corp ......................................Direct from the Vendor 455 Douglas Avenue Holland, MI 49424 Tele: 616-396.4604

HP Hartzell Propeller Inc. ........................Any Hartzell Propeller Inc. approved Distributor

HK Hocking NDT Ltd ...............................Direct from the Vendor 50 Industrial Park Road Lewistown, PA 17044 Tele: 717-242-0320 Fax: 717-242-4170

IP Innovative Peening System ..............Either through the Hartzell Propeller Inc. 2825 Simpson Circle distributor network, or it may be purchased Norcross, GA 30071 directly from the vendor Tele: 770-246-9883 Fax: 770-246-9860 Email: [email protected] www.ipeenglobal.com

JC Jay Instrument and Spec Co. ............Direct from the Vendor 555 North Wayne Avenue Cincinnati, Ohio 45215

JL J & L Metrology Division....................Direct from the Vendor Vermont Precision Machine Services P.O. Box 10 280 Clinton Street Springfield, VT 05156, USA Tele: 802-885-8291 Fax: 802-885-2404 www.jlmetrology.com/

KE Keithley Instruments, Inc. ..................Direct from the Vendor 28775 Aurora Road Solon, OH 44139 Tele: 800-348-3735 Fax: 440-498-2980




LC Leschen Wire Rope ..........................From any Distributor St. Joseph, MO 64502

LE Lee Valve Company ..........................Direct from the Vendor 9701 W. Higgins Road Suite 380 Rosemont, IL 60018

LI Lincoln Industrial Corporation ...........Direct from the Vendor 4130 Tumwater Truck Route Port Angeles, WA 98363 Tele: 360-457-6122 Fax: 360-452-4773 Email: [email protected] www.lincolnindustrialcorp.com/

MA Matco Tools .......................................Direct from the Vendor 4403 Allen Road Stow, OH 44224 Tele: 866-289-8665 Fax: 330-926-5323 www.matcotools.com

MC McMaster-Carr Supply Co. ...............Direct from the Vendor P.O. Box 4355 Chicago, IL 60680

MF Magnaflux Corp. ................................Direct from the Vendor 7300 W. Lawrence Avenue Chicago, IL 60656

MG Magnetix Triad. .................................Either through the Hartzell Propeller Inc. distributor network, or it may be purchased directly from the vendor or distributor

MH Mahr Federal Inc. ..............................Either through the Hartzell Propeller Inc. 1144 Eddy Street distributor network, or it may be purchased P.O. Box 9400 directly from the vendor Providence, RI Tele: 401-784-3100 Fax: 401-784-3246

MI Metal Improvement Co. .....................Either through the Hartzell Propeller Inc. Curtiss-Wright Surface Technologies distributor network, or it may be purchased 11131 Luschek Drive directly from the vendor Blue Ash, OH 45241 Tele: 513-489-6484 Fax: 513-489-6899 www.cwst.com

MS Mausner Equipment Company, Inc. ..Direct from the Vendor 651 Pierce Place East Meadow, NY 11554 Tele: 516-481-1600




MT Mitutoyo America Corporation ...........Direct from the Vendor 965 Corporate Blvd. Aurora, IL 60504 Tele: 630-820-9666 Fax: 630-820-2614 E-mail: [email protected]

MV Micro-Vu Corp. ..................................Direct from the Vendor 7909 Conde Lane Windsor, CA 92492, USA Tele: 707-838-6272 Fax: 707-838-3985

NT N.T. Ruddock Company. ...................Either through the Hartzell Propeller Inc. 26123 Broadway Ave. distributor network, or it may be purchased Cleveland, OH 44146 directly from the vendor or distributor Tele: 440-439-4976 Fax: 440-439-8728 Email: [email protected] www.ntruddock.com

OL Olympus NDT Inc. ............................Direct from the Vendor 9 Woerd Ave. Waltham MA, USA www.olympus-ims.com Tele: 1-800-225-8330

OT OTC Tools Inc. ..................................Direct from the Vendor Bosch Automotive Service Solutions 28635 Mound Road Warren, MI 48092 Tele: 800-533-6127 Fax: 800-283-8665 Email: [email protected] www.otctools.com

International Tele: 507-455-7223 Fax: 507-455-7063 Email: [email protected]

PG PPG Aerospace ................................Direct from the Vendor 6022 Corporate Way Indianapolis, IN 46278 Tel: 317-328-4643 Fax: 317-290-1300 www.ppgaerospace.com




PH Parker Hannifin Co.. ..........................Either through the Hartzell Propeller Inc. 6035 Parkland Boulevard distributor network, or it may be purchased Cleveland, OH 44124 directly from the vendor or distributor Tele: 216-896-3000 Toll Free: 800-272-7537 Email: [email protected] www.parker.com

PM Panametrics, Inc. ..............................Direct from the Vendor 221 Crescent Street Waltham, MA 02154

RC Related Components Inc. .................From any Distributor 3186 Plainfield Road Dayton, OH 45432 Tele: 937-253-6116

SA Steinel America .................................Direct from the Vendor 9051 Lyndale Ave., South Bloomington, MN 55420 Tele: 612-888-5950

SC Stancor ..............................................Either through the Hartzell Propeller Inc. Tele: 602-275-3800 distributor network, or it may be purchased Email: [email protected] directly from the vendor or distributor www.stancor.com

SI S-T Industries, Inc. ............................Direct from the Vendor 301 Armstrong Blvd. N. St. James, MN 56081, USA Tele: 507-375-3211 Fax: 507-375-4503 www.stindustries.com/

SM Steelman Pro ....................................Direct from the Vendor JS Products, Inc. 6445 Montessouri Street Las Vegas, NV 89113 Tele: 702-362-7011 Toll Free: 800-255-7011 Fax: 775-898-8773 Email: [email protected] www.steelmanpro.com

SO Snap-On Tools Corp. ........................Either through the Hartzell Propeller Inc. P.O. Box 14003 distributor network, or it may be purchased Fairfield, OH 45014 directly from the vendor




SP SAE Products. ...................................Direct from the Vendor 1709 Husted Road Suite #4 Conway, SC 29526 Toll Free: 800-588-8480 Fax: 843-349-0738 Email: [email protected] www.saeproducts.com

SQ Square D ...........................................Either through the Hartzell Propeller Inc Schneider Electric distributor network, or it may be purchased 9870 Crescent Park Dr. directly from the distributor West Chester Township, Ohio 45069 Tele: (513) 755-5000 www.schneider-electric.us

ST Starrett Tool Co. ................................Direct from the Vendor or Distributor Athol, MA 01331

TM Thexton Manufacturing Company. ....Direct from the Vendor 6539 Cecilia Circle Edina, MN 55439 Tele: 952-831-4171 Toll Free: 800-328-6277 Fax: 952-831-5938 Email: [email protected] www.thexton.com

US USF Surface Prep. ............................Either through the Hartzell Propeller Inc. distributor network, or it may be purchased directly from the distributor

VK Van Keuren .......................................Direct from the Vendor 107 SCT Drive White House, TN 37188 Tele: 847.439.9220

VR VWR Scientific ..................................Direct from the Vendor P.O. Box 66929 Chicago, IL 60666

WI Wahl Instruments, Inc. ......................Direct from the Vendor 5750-A Hannum Ave. Culver City, CA 90231 Tele: 800.344.9245

WH White Hawk Machine & Tool .............Direct from the Vendor 6008 Highway 66 Greenville, TX 75402 Tele: 903.450.1060




C. Page

(1) The item is located on the page number listed in the Page column.

2. Using the “TE” Reference Number

A. In other Hartzell Propeller Inc. publications, tooling references appear with the prefix “TE” directly following the tool name to which they apply.

(1) For example, a template which is reference number 133 will appear as: template TE133.

3. Ordering Parts

A. When ordering vendor tooling from the vendor or a distributor, use the number as specified in the manual.

B. For some vendor tooling there is an associated Hartzell Propeller Inc. part number. This part number may be used when ordering the tooling direct from Hartzell Propeller Inc.


TOOL AND EQUIPMENT INDEX 61-00-65 Page 1-1Rev. 25 Sep/19

TE NUMBER PART NUMBER DESCRIPTION VENDOR PAGE

TE2 BST-2912-9 Adaptor HP 2-26TE3 BST-3035 Adaptor HP 2-44TE4 BST-2912-4 Adaptor Ring HP 2-26TE5 AST-2877 Torque Wrench Adaptor HP 2-6TE6 BST-2837 Torque Wrench Adaptor HP 2-19TE7 BST-10008 PCU Tester - Obsolete OBSTE8 CST-2919 Balance Arbor CS 2-85TE9 BST-2853 Assembly Tool HP 2-20TE10 CST-3021 Dual Acting Propeller Assembly Bench HP 2-89TE11 BST-2823 Spinner Mounting Plate Bender CS 2-17TE12 CT-1311 Shot Peen Cabinet CS 2-62TE13 BST-2942 Shank Protection Cap HP 2-31TE14 BST-2943 Shank Protection Cap HP 2-31TE15 BST-2944 Shank Protection Cap HP 2-31TE16 BST-2945 Shank Protection Cap HP 2-31TE17 AST-2803 Ring Centering Tool HP 2-2TE18 CST-2923 Optical Comparator Overlay HP 2-86TE19 CST-2924 Optical Comparator Overlay HP 2-86TE20 CST-2925 Optical Comparator Overlay HP 2-86TE21 CST-2926 Optical Comparator Overlay HP 2-86TE22 CST-2989 Optical Comparator Overlay HP 2-86TE23 DST-10014 Synchrophaser Check Box HP 2-98TE24 CST-2800 Blade Retention Components Clamp CS 2-80TE25 CST-2929 Blade Retention Components Clamp CS 2-86TE26 BST-3038 Control Rod Alignment Tool HP 2-45TE27 AST-2870 Hub Bearing Radius Comparator HP 2-5TE28 CUST. P/N Optical Comparator CS 2-108TE29 AT-725-1 Spring Compressor HP 2-9TE30 BST-2826 Spring Compressor Assembly HP 2-18TE31 BST-2826-1 Spring Compressor Assembly HP 2-19TE32 CST-3016 Portable Spring Compressor HP 2-89TE33 SCO38 Crowfoot 1 3/16 inch SO 2-112TE34 SC040 Crowfoot 1 1/4 inch SO 2-112TE35 SC042 Crowfoot 1 5/16 inch SO 2-112TE36 SC048 Crowfoot 1 1/2 inch SO 2-112TE37 SC052 Crowfoot 1 5/8 inch SO 2-112TE38 SC056 Crowfoot 1 3/4 inch SO 2-112TE39 SC060 Crowfoot 1 7/8 inch SO 2-112TE40 BST-3027 Modified Crowfoot HP 2-41TE41 BST-3030 Modified Crowfoot HP 2-42TE42 BST-3031 Modified Crowfoot HP 2-42TE43 BST-3033 Modified Crowfoot HP 2-43




TE44 170-1/4 Apex Torqset Bit AP 2-112TE46 BST-3060-1 Screw Driver HP 2-52TE47 YA484 Tool Box SO 2-91TE48 CT-1075 Adjustable Riser Fixture HP 2-93TE49 BT-1312 Almen Strip Fixture HP 2-62TE50 BST-5845 Chamfering Tool HP 2-55TE51 BST-2920 Drill Fixture HP 2-27TE52 CST-2913 Pilot Tube Press Fixture HP 2-81TE53 DT-336 Pilot Tube Removal Fixture HP 2-99TE53-1 DT-336+6 Jaw HP 2-99TE53-2 DT-336+7 Jaw HP 2-99TE54 BST-2892 Piston Fixture HC-B3( )30-2E HP 2-23TE55 BST-2892-1 Piston Fixture All #20 Spline HP 2-23TE56 BST-2892-2 Piston Fixture HC-B3( )30-2B HP 2-23TE57 BST-2908 Piston Fixture ( )HC-A3VF-4 and HC-B3WF-4 HP 2-24TE58 BST-10006 Rigging Cover HP 2-58TE59 CST-2914 Spring Compressor Fixture HP 2-82TE60 BST-2812 Counterweight Clamp Gauge HP 2-16TE61 BST-2964 Thickness Gauge HP 2-37TE62 BST-2958L Hoist Ring Combo HP 2-35TE63 BST-3036 Piston Installation Cone HP 2-44TE64 BST-2985 Bearing Installation Tool HP 2-39TE64-1 BST-2985-1 Bearing Installation Tool HP 2-39TE65 AST-2849 Beta Rod Retainer Installation Tool HP 2-4TE66 7552-4/791975524 Helicoil Insert Installation Tool HE 2-114TE66-1 7552-5/791975525 Helicoil Insert Installation Tool HE 2-114TE66-2 7552-7/791975527 Helicoil Insert Installation Tool HE 2-114TE67 KHT9000-9 Thread Insert Installation Tool AL 2-111TE68 BST-3047 Thread Insert Installation Tool HP 2-48TE68-1 BST-3047-8 Thread Insert Installation Tool HP 2-48TE68-3 BST-3047-3 Thread Insert Installation Tool HP 2-48TE68-4 BST-3047-4 Thread Insert Installation Tool HP 2-48TE68-5 BST-3047-5 Thread Insert Installation Tool HP 2-48TE68-6 BST-3047-6 Thread Insert Installation Tool HP 2-48TE68-7 BST-3047-7 Thread Insert Installation Tool HP 2-48TE68-8 BST-3047-2 Thread Insert Installation Tool HP 2-48TE68-9 BST-3047-1 Thread Insert Installation Tool HP 2-48TE69 BST-10001 Transfer Tube O-ring Installation Tool HP 2-56TE70 BST-3056 PCU Bushing Installation Tool HP 2-51TE71 BST-3057 PCU Bushing Installation Tool HP 2-51TE72 BST-3054 PCU Manifold Installation Tool HP 2-50




TE73 AST-2856 Pilot O-ring Installation Tool HP 2-4TE74 BST-3037 Aft Control Spring Compressor HP 2-45TE75 BST-2982 Drill Jig HP 2-38TE76 BST-2983 Drill Jig HP 2-38TE78 CST-3028 Dual Acting Propeller Assembly Tool Kit HP 2-90TE79 CST-3028-1 Dual Acting Line Maintenance Tool Kit HP 2-92TE80 BST-2912-10 “C” Flange Spindle HP 2-26TE81 796514021 Vacuum Pump 54976-029 VR 2-1TE82 A-2334 Tool Kit HP 2-1TE83 AST-2833 Safety Nozzle HP 2-3TE84 BST-3041 Rigging Pin HP 2-46

TE85 BST-2912-11 Anti-rotation Pin HP 2-26TE86 BST-2958 Pitch Angle Stop Plug HP 2-35TE87 BST-2938 Shot Peen Plug HP 2-29TE88 BST-2939 Shot Peen Plug HP 2-73TE89 BST-2939N Shot Peen Plug HP 2-30TE90 BST-2940 Shot Peen Plug HP 2-30TE91 BST-2941 Shot Peen Plug HP 2-31TE92 BST-2946 Shot Peen Plug HP 2-32TE93 DST-2934 Blade Bearing Press HP 2-93TE94 AST-2857 Superseded by TE94-1 n/a n/aTE-94-1 107514 "Y" Shank Eddy Current Probe HP 2-5TE95 BT-1313(-)( ) Eddy Current Probe Unit OL 2-63

TE96 799200105 PE 105 Bench Top Blade Angle Protractor PE

HP 2-111

TE97 BST-2960-3 Digital Protractor HP 2-36TE98 BST-3045 Puller HP 2-47TE99 BST-3039 Bearing Puller HP 2-46TE100 CST-2987 Beta System Puller HP 2-87TE101 BST-2947 Bushing Puller HP 2-32TE102 BST-2948 Bearing Puller HP 2-33TE103 BST-2949 Bearing Puller HP 2-33TE104 BST-2950 Bearing Puller HP 2-34TE105 BST-2951 Bearing Puller HP 2-73TE106 BST-2952 Bearing Puller HP 2-34TE107 BST-2876 Pilot Tube Puller HP 2-21TE108 BT-223 Retention Bearing Puller HP 2-60TE108-1 BT-223+9 Adaptor CS, HP 2-60TE108-2 BT-223+10 Adaptor CS, HP 2-60TE109 GFS081 Socket, 6 Point, 1/8 inch, 3/8 Drive SO 2-92TE110 BST-3065 Blade Shot Peen Plug Removal Tool HP 2-55




TE111 1227-6 Helicoil Insert Removal Tool HE 2-114TE112 BST-3019 Thread Insert Removal Tool HP 2-40TE112-1 BST-3019-3 Thread Insert Removal Tool HP 2-40TE112-3 BST-3019-4 Thread Insert Removal Tool HP 2-40TE112-4 BST-3019-8 Thread Insert Removal Tool HP 2-40TE112-5 BST-3019-7 Thread Insert Removal Tool HP 2-40TE113 BST-2884 Plug-Lifting Ring HP 2-22TE114 BST-2959 Alignment Check Rod HP 2-36TE115 BST-2984 Alignment Check Rod HP 2-39TE116-3 DT-1724-3( ) Rolling Machine HP 2-100TE116-5 DT-1724-5 Automated Rolling Machine HP 2-100TE117 BST-10002 Beta Valve Freeze Sleeve HP 2-56TE118 BST-3060 Shot Peen Masking Tool HP 2-52TE-118-1 BST-3060-2 Shot Peen Masking Tool HP 2-52TE119 AST-2961 Shipping Sleeve HP 2-8TE120 BST-2922 Modified Deep Well Socket HP 2-28TE121 AST-2979 Test Specimen for Calibration HP 2-13TE122 BST-2912-2 #20 Spline Spindle HP 2-26TE123 BST-2912-3 #30 Spline Spindle HP 2-26TE124 BST-2912-1 Flanged Hub Spindle HP 2-26TE125 BST-2912 Building Buck Components HP 2-26TE125-1 BST-2912+ Building Buck Components HP 2-26TE126 BST-3024 Blade Assembly Support Stand HP 2-40TE128 BST-2847 Probe Support HP 2-20TE129 CST-2901-( ) Propeller Assembly Table HP 2-97TE131 BST-2825 Template HP 2-18TE132 79651417A Vacuum Filter 55007-020 VR 2-1TE133 ED-520 Eddy Current Test Instrument MF 2-110TE134 ED-530 Eddy Current Test Instrument MF 2-110TE135 79656547A Timer, 12 Hour 6X547 PE 2-1TE136 BST-10003 Flight Idle Set Fixture HP 2-57TE137 BT-1271-1,2 Shot Peen Tube Assembly HP 2-61TE138 AST-2802 Plastic Wedge HP 2-1TE139 AST-2805 Torque Wrench Adaptor HP 2-2TE139-2 AST-2805-2 Torque Wrench Adaptor HP 2-2TE141 BST-3044 Clamp Wrench HP 2-47TE142 BST-2813 Clamp Nut Wrench HP 2-17TE143 BST-3032 Open End Wrench HP 2-43TE144 SC046 Piston Nut Wrench SO 2-25TE144-1 SC058 Piston Nut Wrench SO 2-25TE145 n/a Superseded by TE144-1 n/a n/aTE146 BST-2910 Shaft Nut Wrench HP 2-15




TE147 79651407K Vacuum Oil 54996-252 VR 2-1TE148 BT-461 Spanner Wrench HP 2-59TE148-1 100923 Strap Wrench HP 2-59TE149 AST-2814 Torque Wrench Adaptor HP 2-3TE150 BST-2860 Torque Wrench HP 2-21TE152 AST-2917 Torque Wrench Adaptor HP 2-6

TE153 BST-2921 BST-2921-1 Torque Wrench Adaptor HP 2-27

TE154 AST-2953 Torque Wrench Adaptor HP 2-7TE155 AST-2877-1 Torque Wrench Adaptor HP 2-6TE156 796540702 Vacuum Hose YA-6407-02 CP 2-1TE157 BST-10005 Beta Switch Tester HP 2-58TE158 79651009A Vacuum Gauge 1009A JC 2-1TE159 BST-10007 Threaded Headless Pins HP 2-59TE160 7965639221 Vacuum Fitting YA-6392-21 CP 2-1TE166 GTMU121 Universal Socket, 12 Point, 3/8 inch, 1/4 Drive SO 2-92TE176 APS351 Adjustable Spanner Wrench, 1/8 Pin SO 2-92TE181 BST-2966 Spinner Support Plate Ream Fixture HP 2-37TE182 BST-2966-3 Spinner Support Plate Ream Fixture HP 2-37TE183 BST-2966-4 Spinner Support Plate Ream Fixture HP 2-37TE184 BST-2966-5 Spinner Support Plate Ream Fixture HP 2-37TE185 BST-3055 PCU Bearing Installation Tool HP 2-50TE186 BST-3055-1 PCU Bearing Installation Tool HP 2-50

TE192 GFC48A Crowfoot Wrench, Open End with Side Lock Hole, 1 1/2 inch, 3/8 Drive SO 2-92

TE202 GFS161 Deep Well Socket, 12 Point, 1/2 inch, 3/8 Drive SO 2-92TE207 BT-1465-1 Floating Reamer HP 2-64TE207-1 BT-1465-3 Floating Reamer HP 2-64TE208 BT-1465-2 Floating Reamer HP 2-64TE208-1 BT-1465-4 Floating Reamer HP 2-64

TE214 GFC012 Crowfoot Wrench, Open End, 3/8 in SO2-902-92

TE228 BST-3067 Piston Installation Socket HP 2-29TE228-1 BST-3067+3 Piston Installation Socket HP 2-29TE229 GFA4A Socket Driver, 5/32 Hex. Head, 3/8 Drive SO 2-92TE238 BST-3026-1 Bearing Press HP 2-41TE239 BST-3026-2 Bearing Press HP 2-41TE240 BST-3026-3 Bearing Press HP 2-41TE241 BST-3064 Pilot Tube Installation Tool Kit HP 2-54TE241-1 BST-3064A Pilot Tube Installation Tool Kit HP 2-54TE242 BST-3064-1 Pilot Tube Installation Tool HP 2-54TE243 BST-3064-2 Pilot Tube Positioner and Stop HP 2-54




TE244 BST-3064-3 Pilot Tube Positioner and Stop HP 2-54TE245 BST-3064-4 Pilot Tube Positioner and Stop HP 2-54TE246 BST-3064-5 Pilot Tube Positioner and Stop HP 2-54TE247 BST-3068 Peening Tool HP 2-65TE248 GF10M Breaker Bar, 3/8 Drive SO 2-92TE249 GVO1820 Open End Wrench, Std Length, 9/16 - 5/8 in SO 2-91TE250 PFDH180 Socket, 12 Point, 9/16 inch, 3/8 Drive SO 2-91TE251 BST-10004 Modified Deep Well Socket HP 2-57TE252 668 Thickness Gauge ST 2-91TE253 QJFR275E Adjustable Torque Wrench, 5 to 75 ft-lb, 3/8 Drive SO 2-91TE254 QJR217C Adjustable Torque Wrench, 30 to 200 in-lb, 3/8 Drive SO 2-91TE255 GFX1 Extension, 2 inches, 3/8 Drive SO 2-91TE256 GFC60A Crowfoot Wrench, 1 7/8 inch, 3/8 Drive SO 2-91TE257 ASA204A Miniature Pick Set SO 2-91TE258 170-6 Apex Torqset Bit, 1/4 inch, 1 1/4 Length AP 2-91TE259 1500-P Hand Driver, Replaceable-Bit AP 2-91TE260 90303A247 Nylon Jack Screws MC 2-91TE261 BLX13 Ball Head Hex. Wrench Set BH 2-92

TE262 EN1901 Propeller Sling, 1 inch x 3 feet LC2-902-92

TE263 CUTA2810114C Installation & Extraction Tool for Relief Valve LE 2-91TE264 CUTA1870104C Installation & Extraction Tool for Oil Nozzle LE 2-91TE265 M22520/1-01 Beta Light Switch Crimping Tool DM 2-91TE266 CUTA1560203A Lee Plug Installation Tool LE 2-91TE267 CUTA1560103B Lee Plug Extraction Tool LE 2-91TE268 CUTA2180203B Lee Plug Installation Tool LE 2-91TE269 CUTA2180103B Lee Plug Extraction Tool LE 2-91TE270 CUTA2810203B Lee Plug Installation Tool LE 2-91TE271 CUTA2810103B Lee Plug Extraction Tool LE 2-91TE272 CUTA3120203B Lee Plug Installation Tool LE 2-91TE273 CUTA3120103B Lee Plug Extraction Tool LE 2-91TE274 BST-2970 PCU Bearing Seat Sander HP 2-66TE275 MR02030 Roller, Steel 1½" x 2" EP 2-115TE276 CST-3028-2 Dual Acting Line Maintenance Tool Kit HP 2-92TE277 CST-3012 Ultrasonic Inspection Calibration Standard HP 2-95TE282 AST-2827 Spring Compressor Bolt HP 2-18

TE283 BST-2828 Spring Compressor Slide HP2-182-19

TE284 AST-2827-1 Spring Compressor Bolt HP2-192-85

TE285 791256000 Ultrasonic Flaw Detector Kit PM 2-109TE287 BST-2850 Threaded Rod HP 2-20




TE288 AST-2852 Drilled Washer HP 2-20TE289 BST-3152 Thrust Bearing HP 2-20TE290 BST-3151 5/8 Hex Nut HP 2-20TE291 AST-2851 Guide Washer HP 2-20TE295 BST-2832 Superseded by BT-1313 n/a OBSTE296 BST-3070 Drill Jig, PCU HP 2-67TE297 BST-3071 PCU Stand HP 2-67TE298 BST-2932 Dummy Pitch Change Rod HP 2-28TE299 BST-10037 E13890 Master Blade, Group 1 CS 2-68TE300 BST-10038 E13890 Master Blade, Group 2 CS 2-68TE301 BST-10039 E13890 Master Blade, Group 3 CS 2-68TE302 HZP161001 E10950 Blade Repair Blanket BR 2-115TE303 HL1802E Heat Gun SA 2-116TE304 HZP161002 Blade Repair Blanket (4" x 12") BR 2-115TE305 PMF133 0 - 6 inch Dial Calipers SO 2-91TE306 240-120F Temp-Plate® Recorder 120°F to 180°F WI 2-116TE307 240-190F Temp-Plate® Recorder 190°F to 220°F WI 2-116TE308 BST-3061 Press Tool HP 2-53TE309 BST-3062 Press Tool HP 2-53TE310 BT-3035 Centering Tool for C-5623-2 Drive Coupling HP 2-68TE311 BST-3066-2 Stop Adaptor HP 2-65TE312 n/a Superseded by TE389-3 n/a OBSTE313 n/a Superseded by TE389-4 n/a OBSTE314 n/a Superseded by TE389-1 n/a OBSTE315 BST-3069 Eddy Current Fixture HP 2-66TE316 9943HART-001 Unfeathering Tool CG 2-117TE318 DST-3049-( ) Ground Hydraulic Power Unit (GHPU) HP 2-98TE319 AST-2981 Assembly Guide HP 2-9TE320 BST-3048 Transfer Tube and Plug Removal/Installation Tool HP 2-48TE321 BST-2811 Flatness Gauge HP 2-16TE323 CUTA1250203A Lee Plug Installation Tool LE 2-91TE324 CUTA1250103B Lee Plug Extraction Tool LE 2-91TE325 n/a Superseded by TE122 n/a OBSTE326 n/a Superseded by TE123 n/a OBSTE328 MR01020 Roller, Smooth 1 1/8" x 1/8" EP 2-115TE329 MR10900 Roller, Gooseneck 1" x 1/16" EP 2-115TE330 MR05000 Roller, Rubber 2" EP 2-115TE331 MR05020 Roller, Silicon 1 5/16" x 1¾" EP 2-115TE332 GS4H Tie Strap Gun AE 2-117TE333 AT-3010 Balance Tube Positioner HP 2-10TE334 AT-3011 Balance Tube Positioner HP 2-10TE343 n/a Superseded by BT-1313 n/a OBS




TE344 n/a Superseded by BT-1313 n/a OBS

TE353 BST-2930-5 SR19W4-A Slimsert® Installation Tool

HP RC 2-13

TE354 CUST. P/N Megohm Meter AR 2-119TE355 CUST. P/N Milliohmmeter AR 2-120TE356 CG40-4 PCU Filter Removal Tool, Rod SO 2-109TE357 CG40-7 PCU Filter Removal Tool, Collet SO 2-109TE358 240-090F Temp-Plate® Recorder 90°F - 120°F WI 2-118TE359 90F2312 Signal Generator Model 3001 BK 2-118TE360 BST-10015 Modified Crowfoot SO 2-69

TE361 DST-10024 DST-10024-1 Bolt Alignment Tool HP 2-101

TE362 BST-10026 Pitch Lock Roller Fixture HP 2-69TE363 DST-10016 Roller Assembly Tool HP 2-101TE364 DST-10025 Go-No-Go Gauge HP 2-102

TE365 CG250-8A CG250-9 Slide Hammer, 2 lb. SO 2-121

TE366 CG41-11 Slide Hammer, Rod SO 2-121TE367 CG41-14 Slide Hammer, Collet, 1/4 inch to 5/16 inch SO 2-121TE368 CG41-13 Slide Hammer, Collet, 3/8 inch to 7/16 inch SO 2-121TE369 MS27495R20 Pin Extractor CS 2-120TE370 000-951-005 Bransonic Cleaner Model B3 BN 2-119TE371 BST-3080 Shot Peen Plug HP 2-70TE372 BST-3080-1 Shot Peen Plug HP 2-70TE373 CST-10050 Optical Comparator Overlay HP 2-86TE374 CUST. P/N Transducer Assembly PM 2-122TE375 Approved Units Ultrasonic Flaw Detector Cust. P/N 2-122TE379 02643 Shot Peen Gun CL 2-123TE380 CST-3110 Cylinder Cap HP 2-94TE381 BST-3109 T-Handle Wrench HP 2-71TE382 DST-3146 Thread Gauge Airflow Kit HP 2-104TE382-1 DST-3146-1 Thread Gauge Airflow Kit HP 2-104TE383 BST-3103 Feathering Tool HP 2-71TE384 BST-3104 Cylinder Installation Rod HP 2-72TE385 BST-2837+1+3 Modified Socket HP 2-19TE386 BST-2837+2 Anti-Rotation Pin HP 2-19TE387 B-3368 5/16-24 Hex Nut HP 2-20TE388 A-3204 5/16-24 Set Screw HP 2-20

TE389-1

BST-2930-1 SR25W4A MR25W4A 225-072722

Slimsert® Installation Tool

HP RC MK AC

2-113




TE389-2

BST-2930-2 SR43W4A MR43W4A 225-072734


HP RC MK AC

2-113

TE389-3

BST-2930-3 SR50W4AMR50W4A 225-072738 225-890051


HP RC MK AC AC

2-113

TE389-4

BST-2930-4 SR56W4A MR56W4A 225-072742 225-890053


HP RC MK AC AC

2-113

TE389-5

BST-2930-5 SR19W4A MR19W4A 225-072718


HP RC MK AC

2-113

TE389-6

BST-2930-6 SR16W4AMR16W4A 225-072714


HP RC MK AC

2-113

TE389-7

BST-2930-7 SR37W4A MR37W4A 225-072730


HP RC MK AC

2-113

TE389-8

BST-2930-8 SR31W4AMR31W4A 225-072726


HP RC MK AC

2-113

TE389-9

BST-2930-9 SR14W4AMR14W4A 225-072710


HP RC MK AC

2-113

TE389-10

BST-2930-10 SR11W4AMR11W4A 225-072706


HP RC MK AC

2-113

TE390 DT-2997-2 Pressure Check Adapter CS 2-103TE391 DT-2997-4 Pitch Change Bore Plug CS 2-102TE392 DT-2997-5 Pitch Change Bore Plug CS 2-102TE393 DT-2997-7 Pressure Check Adapter CS 2-103TE394 DT-2997-8 Pressure Check Adapter CS 2-103TE395 0.0525 inch dia. Gear Inspection Wire VK 2-128TE396 0.0620 inch dia. Gear Inspection Wire VK 2-128TE397 0.0850 inch dia. Gear Inspection Wire VK 2-128TE398 0.2634 inch dia. Gear Inspection Wire VK 2-128




TE399 0.2700 inch dia. Gear Inspection Wire VK 2-128TE400 0.0962 inch dia. Gear Inspection Wire VK 2-128TE401 0.1400 inch dia. Gear Inspection Wire VK 2-128TE402 0.1480 inch dia. Gear Inspection Wire VK 2-128TE403 BST-3022 Reamer HP 2-72TE403-1 BST-3022A Reamer HP 2-72TE404 AST-2968 Stud Installation/Torque Check Tool HP 2-12TE404-1 AST-2968-1 Stud Installation/Torque Check Tool HP 2-12TE404-2 AST-2968-2 Stud Installation/Torque Check Tool HP 2-12TE405 AST-3163-( ) Shot Peen Plug Kit HP 2-11TE406 AST-3157 Shot Peen Plug HP 2-11TE407 AST-2971-1 Screw - 0.50 inch (12.7 mm) HP 2-11TE408 AST-2971-2 Screw - 0.62 inch (15.7 mm) HP 2-11TE409 A-2327 Slimsert® Repair Kit HP 2-12

TE410 B-6986-258 SR258 Slimsert®

HP RC 2-12

TE411 791762313 5/16-24 UNF-3B MOD Tap HP

RC 2-12

TE412 BST-2931-1 SR25D Step Drill HP

RC 2-12

TE413 CST-2969 Blade Angle Locating Fixture HP 2-94TE414 BST-3006 Paint Mask Cap HP 2-74TE415 BST-3158 Paint Mask Cap HP 2-74TE416 BST-3159 Paint Mask Cap HP 2-74TE417 BST-3160 Paint Mask Cap HP 2-74TE418 BST-3161 Paint Mask Cap HP 2-74TE419 BST-3162 Paint Mask Cap HP 2-74TE420 BST-2991 Spacer HP 2-75TE421 AST-3154 Slimsert® Repair Kit HP 2-13

TE422 B-6986-192 SR192 Slimsert®

HP RC 2-13

TE423 99620070 1/4-28 UNF-3B Superseded by 106511, TE601 HP

RC OBS

TE424 BST-2931-5 SR19D Step Drill HP

RC 2-13

TE427 CST-3169 Sleeve Installation Tool HP 2-95TE428 BST-3081 Mask Screw HP 2-75TE429 DT-2997-9 Pressure Check Adapter CS 2-103

TE430 0.2760 Pin Gauge, Minus "Y" Tolerance No Go Gauge HM 2-124

TE431 BST-3200 E13890 Master Blade, Group 0 CS 2-68TE432 AST-3175 Torque Wrench Adaptor CS 2-7




TE433 BST-2912-17 A Flange Spindle HP 2-26TE434 101088 Eddy Current Probe HP 2-124TE435 CST-3015 Calibration Standard HP 2-96TE436 AST-3475 Superseded by TE436-2 n/a 2-15TE436-1 AST-3475-1 Superseded by TE436-2 n/a 2-15TE436-2 AST-3475-2 Profilometer MH 2-15TE437 BST-3227 Probe Housing Component HP 2-76TE438 BST-3226 Blade Pitch Fixture CS 2-76TE439 AST-3174 Ball Hex Driver HP 2-14TE440 BST-3177 Blade Seal Alignment Tool HP 2-77TE440-1 BST-3063 Blade Seal Alignment Tool HP 2-77TE441 BST-7587 Pressure Check Tool CS 2-79

TE441-1 BST-7587-1 Pressure Check Tool - Kit without the Pilot Tube Installation Tool CS 2-79

TE441-2 BST-7587-2 Pressure Check Tool CS 2-79TE441-3 BST-7587-3 Pressure Check Tool CS 2-79TE441-4 BST-7587-4 Pressure Check Tool CS 2-79TE441-5 BST-7587-5 Pressure Check Tool CS 2-79TE442 BST-4114 Composite Balance Tube Puller CS 2-77TE443 BT-3838 Grease Seal Pressure Test Tool (Adapter) HP 2-78TE443-1 BT-3838-1 Grease Seal Pressure Test Tool HP 2-78TE444 DST-3483 Masking Fixture CS 2-99TE445 BST-7588 Insert Installation Tool CS 2-64TE446 DST-5855(F) Shot Peen Machine Assembly CS, WH 2-105TE447 DST-5855-1(F) Blade Shank Knob Shot Peen Kit HP 2-107TE448 CST-3178 Bolt Alignment Fixture HP 2-96TE449 101679 "E" Shank Form Tool HP 2-125TE449-1 105473 "E" Shank Form Tool HP 2-125TE450 101736 "E" Shank Potting Mold HP 2-125TE451 GT-3669 Composite E-shank Comparison Chart HP 2-126TE452 101999 Tube Puller Assembly CS 2-126TE453 101923 Balance Adapter CS 2-127TE454 101781 Plug Puller HP 2-127TE455 101932 Blade Spud Adapter CS 2-151TE456 103570 Mandrel CS 2-128TE457 101939 Torque Wrench Adapter CS, HP 2-129TE458 101060 Shot Peen Plug HP 2-129TE459 103572 Ring CS 2-130TE460 102690 E13890 Master Blade, Group 4 CS 2-68TE486 791911212 212-8 Driver HP 2-130TE487 CST-421 Stud Fixture Plate HP 2-80TE488 BST-2890 Spring Compressor Base HP 2-22




TE488-1 BST-2891 Spring Compressor Base HP 2-22TE488-2 BST-2894 Spring Compressor Base HP 2-22TE488-3 106885 Spring Compressor Base HP 2-22TE489 BST-2895 Spring Compressor Retainer HP 2-23TE489-1 BST-2896 Spring Compressor Retainer HP 2-23TE489-2 BST-2897 Spring Compressor Retainer HP 2-23TE489-3 BST-2899 Spring Compressor Retainer HP 2-23TE489-4 106884 Spring Compressor Retainer HP 2-23TE490 BST-2902 Spring Compressor Guide Rod HP 2-24TE490-1 BST-2903 Spring Compressor Guide Rod HP 2-24TE490-2 BST-2904 Spring Compressor Guide Rod HP 2-24TE490-3 BST-2905 Spring Compressor Guide Rod HP 2-24TE490-4 BST-2907 Spring Compressor Guide Rod HP 2-24TE492 BST-3050 Chip Detector Fitting HP 2-49TE493 BST-3051 Chip Dectector Fitting Cover HP 2-49TE494 BT-1271-4 Shot Nozzle Unit HP 2-61TE494-1 BT-1271-5 Shot Nozzle Unit HP 2-61TE494-2 BT-1271-6 Shot Nozzle Unit HP 2-61TE494-3 BT-1271-7 Shot Nozzle Unit HP 2-61TE494-4 BT-1271-8 Shot Nozzle Unit HP 2-61TE495 104287 Torque Wrench CS 2-131TE496 104371 Stand Adapter MF 2-131TE497 104372 Drive Housing Adapter MF 2-132TE498 104374 Roughness Standard MF 2-132TE499 M22520/37-01 Crimp Tool CS 2-133TE500 BST-3076 Calibration Standard HP 2-133TE501 BST-3077-1 Eddy Current Probe CS 2-134TE502 104933 Fitting Wrench CS 2-134TE503 104811 Spacer Blank CS 2-135TE504 105189 Bearing Assembly Tool CS 2-136TE505 105190 Clamp CS 2-136TE506 104507 Leak Check Manifold CS 2-137TE507 104504 Adapter CS 2-137TE508 104798 Check Cylinder HP 2-138TE509 105167 Check Cylinder CS 2-138TE510 104506 Plug Assembly CS 2-135TE516 BST-3075 Double Shoulder Blade Eddy Current Kit HP 2-139TE517 105266 Torque Unit Adapter CS 2-140TE518 105269 Torque Unit Adapter CS 2-140TE519 BST-2912-20 Hovercraft 5-Way Adapter CS 2-141TE520 BST-2912-21 Hovercraft 6-Way Adapter CS 2-141TE531 105274 Balance Adapter HP 2-142TE532 Contact Hartzell Bantam Blade Spud Adapter HP 2-142




TE533 102560 Leak Detector Kit HP 2-143TE534 105478 Blade Adapter Service Tool HP 2-143TE535 104052 Drill Jig for N7605 Shank HP 2-144TE536 BST-2912-19 “H”, “T”, “Q”, and “G” Flange Spindle HP 2-144TE537 102515 Shank Spacer Puller CS 2-145TE538 102516 Shank Spacer Puller CS 2-145TE539 105501 Blade Inspection Adapter CS 2-151TE540 103454 Stud Preload Plate CS 2-146TE547 105615 Valve Assembly Check Tool CS 2-147TE548 105532 Bantam Spring Compressor HP 2-148TE550 BST-2912-22 "F" Flange Bantam Adapter Ring HP 2-149TE551 AST-2877-2 Torque Wrench Adaptor HP 2-6TE559 105702 Right Angle Grease Coupler HP 2-149TE567 106221 Extended Socket HP 2-150TE568 105236 Air Check Block HP 2-150TE569 106415 "D" Outer Shank Optical Comparator Overlay HP 2-86TE570 106450 Nut Tube HP 2-146TE594 106542 "C" Shank Rolling Conversion Kit HP 2-152TE595 106554 "C" Shank Optical Comparator Overlay HP 2-86TE598 DT-1724+171 Base HP 2-152TE599 DT-1724+172 Ring, Clamp HP 2-152TE600 DT-1724+173 Pin, Locator HP 2-152TE601 DTS-5855+72 Shot Peen, Blade Butt Mini-mask HP 2-153TE602 DTS-5855+73 Shot Peen, Blade Butt Mask HP 2-153TE603 DTS-5855+21 Shotpeen Locknut Oriface HP, NT 2-106TE604 DTS-5855+22 Shotpeen Oriface, Air Jet HP, NT 2-106TE605 DTS-5855+24 Shot Metering Valve HP, NT 2-106TE606 DTS-5855+26 Air Ball Valve HP, NT 2-106TE607 DTS-5855+29 Air Regulator HP, PH 2-106TE608 DTS-5855+33 Plate HP 2-106TE609 DTS-5855+35 Almen Strip Holder HP 2-106TE610 DTS-5855+48 Mask HP 2-106TE614 106784 "N" Shank Optical Comparator Overlay HP 2-86TE615 106804 Plate, Kit HP 2-89TE616 106513 Piston Ring Clamp Kit HP 2-153TE617 106294 Clamp, Ring, Piston HP 2-153TE618 106295 Base, Clamp HP 2-153TE619 106296 Washer, Clamp HP 2-153TE624 106511 Tap HP, RC 2-13TE625 BST-2826-2 Spring Compressor Assembly HP 2-85TE626 BST-2828-1 Spring Compressor Slide HP 2-85TE627 BST-2855 Spring Assembly Tool HP 2-84TE628 BST-2850-1 Threaded Rod HP 2-84TE634 106964 Assembly Low Pitch Spacer HP 2-154TE635 BST-2869-1 Spacer HP 2-152




TE636 107139 Mask HP 2-154TE637 CST-3200 Hardware Kit CS, HP 2-155TE638 107192 Force Gauge CS, HP 2-155TE639 107190 Position Gauge HP 2-156TE640 DT-1724+193 Torque Wrench Adapter HP 2-156TE641 250255 Sealant Gun Assembly PG 2-157TE642 AST-2877-3 Torque Wrench Adapter HP 2-6TE643 107518 Eddy Current Test Shank HP 2-5

Tool KitPart Number: A-2334 (TE82)

Description: Kit to prepare facilities for erosion shield replacement on composite blades. The kit contains the following:

Vendor Vendor P/N Hartzell P/N Description Qty/Size

VR 54976-029 796514021 (TE81) Vacuum Pump 1

VR 55007-020 79651417A (TE132) Filter 1

PE 6X547 79656547A (TE135) Timer, 12-hour 2

VR 54996-252 79651407K (TE147) Vacuum Oil 5 gallons

CP YA-6407-02 796540702 (TE156) Vacuum Hose (6 ea.) 10 feet

JC 1009A 79651009A (TE158) Vacuum Gauge 2

CP YA-6392-21 7965639221 (TE160) Vacuum Fitting 1

Plastic WedgePart Number: AST-2802 (TE138)

Description: Wedge to aid in separating the hub halves of an aluminum hub propeller without scarring the mating surfaces.

TPI-A

ST2

802


TOOL AND EQUIPMENT LIST 61-00-65 Page 2-1Rev. 25 Sep/19

Ring Centering ToolPart Number: AST-2803 (TE17)

Description: Tool to keep internal rings in alignment. Used during assembly of oil transfer unit for A-224-2 Seal in propeller model HC-A2X20-4( )2.

Torque Wrench AdaptorPart Number: AST-2805 (TE139) “K” flange steel hub propellers AST-2805-2 (TE139-2) “D” flange propellers

Description: Wrench to tighten and torque mounting bolts on propellers. Used in conjunction with a standard 1/2 inch square drive torque wrench.

TPI-A

ST2

805

TPI-A

ST2

803


Page 2-2Rev. 25 Sep/19

TOOL AND EQUIPMENT LIST 61-00-65

Torque Wrench AdaptorPart Number: AST-2814 (TE149)

Description: Wrench to tighten and torque 9/16 inch, 12 point mounting bolt. Used in conjunction with a standard 1/2 inch square drive torque wrench.

Supersedes: A-2814

Safety NozzlePart Number: AST-2833 (TE83)

Description: Fitting to ensure safe use of air nozzle.

TPI-A

ST2

833

TPI-A

ST2

814



TPI-A

ST2

856

TPI-A

PS

0201

Beta Rod Retainer Installation ToolPart Number: AST-2849 (TE65)

Description: Tool to crimp the beta rod retainers onto the beta rod. Used in conjunction with a standard vise.

Pilot O-ring Installation ToolPart Number: AST-2856 (TE73)

Description: Installation tool for A-217-1, -2 Plug. For use with A-224-3, -4 Oil Transfer Unit.

NOTE: This part number may be used to order the drawing to permit local fabrication.




TPI-A

PS

0155

ATP

I-JM

-000

172

"Y" Shank Eddy Current Probe and Eddy Current Test ShankPart Number: 107514 (TE94-1) supersedes AST-2857 (TE94)

107518 (TE643)

Description: 107514 "Y" Shank Eddy Current Probe (TE94-1) is used to inspect “Y” shank aluminum blade retention radius. 107518 Eddy Current Test Shank (TE643) is used to set-up the Eddy Current machine before processing blades with the 107514 "Y" Shank Eddy Current Probe (TE94-1).

Hub Bearing Radius ComparatorPart Number: AST-2870 (TE27)

Description: Comparator to ensure proper fit of blade retention bearing into “D” or “Y” shank hubs.

"Y" Shank Eddy Current Probe

(TE94-1)

Eddy Current Test Shank

(TE643)



Propeller Mounting Flange

Aircraft Engine Mounting Flange

Standard Torque Wrench

Torque Wrench Adaptor AST-2877-( )

Mounting Bolt

Propeller Mounting

O-ring

TPI-A

PS

0543

Torque Wrench AdaptorPart Number: AST-2877 (TE5) 5/8 inch Used for lightweight turbine propellers

that use 5/8 -18, 12 point propeller mounting bolt.

AST-2877-1 (TE155) 11/16 inch Used for dual acting and light weight turbine propellers that use mounting nut C-6006.

AST-2877-2 (TE551) 11/16 inch Used for HC-E4P-3K and HC-E5P-3 installation only.

AST-2877-3 (TE642) 11/16 inch Used for Raptor propeller models ( )D3( )-( )K( ).

Description: Wrench adaptor to install and torque mounting bolts. Used in conjunction with a standard 1/2 inch square drive torque wrench.

TPI-J

M-0

0014

3TP

I-JM

-000

144

TPI-J

M-0

0014

5TP

I-JM

-000

146





Description: Wrench to tighten and torque mounting bolts on “L” flange propellers. Used in conjunction with a standard 1/2 inch square drive torque wrench.

TPI-A

ST2

953

Torque Wrench AdaptorPart Number AST-2917 (TE152)

Description Wrench to tighten and torque propeller mounting bolts on “K” flange propellers. Used in conjunction with a standard 1/2 inch square drive torque wrench.

Supersedes: A-1327

TPI-A

ST2

917



Shipping SleevePart Number: AST-2961 (TE119)

Description: Sleeve to prevent damage to air valves on feathering compact propellers during shipping and handling.


Description: Wrench to tighten and torque mounting bolts on “W” flange propellers. Used in conjunction with a standard 1/2 inch square drive torque wrench.

NOTE: This part number may be used to order the drawing of the torque wrench adaptor to permit local fabrication.

TPI-J

M-0

0018

4TP

I-AS

T296

1




Spring CompressorPart Number: AT-725-1 (TE29)

Description: Spring compressor for beta springs during assembly.

Assembly GuidePart Number: AST-2981 (TE319)

Description: Assembly tool for Spring Assemblies. Used with BST-2853 (TE9) Assembly Tool.

NOTE: One order of Assembly Guide AST-2981 includes a quantity of two (2) guides.

TPI-A

ST2

981

TPI-W

1009

1



Balance Tube PositionerPart Number: AT-3011 (TE334)

Description: Balance tube positioner used for installing balance tubes in composite blades used in an aluminum hub propeller.

Balance Tube PositionerPart Number: AT-3010 (TE333)

Description: Balance tube positioner used for installing balance tubes in "M" shank composite blades.

TPI-J

M-0

0018

5TP

I-JM

-000

186




Shot Peen Plug KitPart Number: AST-3163-( ) (TE405)

Description: Kit to mask the chamfered lubrication fittings in two-blade and three-blade aluminum hubs.

Kit:

AST-3163 Kit for two-blade aluminum hubs, includes:

Components Quantity

1 . . . . . AST-3157 (TE406) Shot Peen Plug 4 2 . . . . . AST-2971-1 (TE407) Screw - 0.50 inch (12.7 mm) 2 3 . . . . . AST-2971-2 (TE408) Screw - 0.62 inch (15.7 mm) 2

AST-3163-1 Kit for three-blade aluminum hubs, includes:

Components Quantity

1 . . . . . AST-3157 (TE406) Shot Peen Plug 6 2 . . . . . AST-2971-1 (TE407) Screw - 0.50 inch (12.7 mm) 6

ScrewShot Peen Plug

TPI-A

ST3

157

TPI-A

ST2

971



Stud Installation/Torque Check ToolPart Number: AST-2968 (TE404) (Install/check 1/2-20 [12.7 mm] studs.)

AST-2968-1 (TE404-1) (Install/check 9/16-18 [14.2 mm] studs.) AST-2968-2 (TE404-2) (Install/check 7/16-20 [10.9 mm] studs.)

Description: Used to install hub mounting studs and to check the required torque after stud adhesive cures.

Slimsert® Repair KitPart Number: A-2327 (TE409)

Description: Kit including tools and parts necessary to repair to the lubrication fitting holes in aluminum hubs. The kit contains the following:

Vendor Vendor P/N Hartzell P/N Description Qty

RC SR258 B-6986-258 (TE410) Slimsert® 1

n/a 5/16-24 UNF-3B MOD 791762313 (TE411) Tap 1 (Minor diameter 0.280-0.285 MOD)

RC SR25W4-A BST-2930-1 (TE389-1) Slimsert® Installation Tool 1 (Supersedes TE314)

RC SR25D BST-2931-1 (TE412) Step Drill 1

TPI-A

ST2

968




Slimsert® Repair KitPart Number: AST-3154 (TE421)

Description: Kit including tools and parts necessary to repair the link pin unit safety screw hole. Not shown. The kit contains the following:

Vendor Vendor P/N Hartzell P/N Description Qty

RC SR192 B-6986-192 (TE422) Slimsert® 1

n/a 1/4-28 106511 (TE624) Tap, Flute, 1/4-28 1 (Supersedes TE423)

RC SR19W4-A BST-2930-5 (TE353) Slimsert® Installation Tool 1

RC SR19D BST-2931-5 (TE424) Slimsert®, Step Drill 1

Test Specimen for CalibrationPart Number: AST-2979 (TE121)

Description: Test specimen to calibrate an eddy current instrument before its use.

TPI-A

ST-

2979



Shaft Nut WrenchPart Number: BST-2910 (TE146)

Description: Wrench to tighten the propeller mounting shaft nut on #20, #30 and #40 splined propellers.

Supersedes: BT-2804, BT-840, BST-2804 and BST-840

Ball Hex DriverPart Number: AST-3174 (TE439)

Description: Used with 3/8 inch ratchet on the B-3812-5-16P socket head cap screw to set preload on blade assembly.

TPI-J

M-0

0018

7TP

I-BS

T291

0




ProfilometerPart Number: AST-3475-2 (TE436-2)

Description: Used to measure surface finish in the radius and transition areas of aluminum blade shanks. Probe Housing Component BST-3227 (TE437) is available for use with the Hartzell Propeller Inc. and Mahr Federal models. Stand Adapter 104371 (TE496) and Drive Housing Adapter 104372 (TE497) are available for use with the Mahr Federal Model as an alternate to BST-3227. Use of Stand Adapter 104371 (TE496) and Drive Housing Adapter 104372 (TE497) connect the drive unit to a standard height stand (customer procured) without the use of BST-3227 (TE437).

Hartzell Propeller Inc. Approved Alternates:

Part Number Vendor Part Number Vendor

AST-3475 (TE436) Perthometer 6910431 Mahr Federal Inc. (MH) (no longer available)



AST-3475 (TE436) Surftest SV-600 series Mitutoyo America Corporation (MT) (no longer available)

AST-3475-1 (TE436-1) MarSurf PS1-1 6910214 Mahr Federal Inc. (MH) (no longer available)

AST-3475-2 (TE436-2) MarSurf PS10 6910230 Mahr Federal Inc. (MH) (supersedes AST-3475 and AST-3475-1, no alternatives are approved)

TI-1

65A

ST3

475

TPI-J

M-0

0017

4

MarSurf PS1 6910214AST-3475-1 (TE436-1)Mahr-Federal Inc. (MH)

MarSurf PS10 6910230AST-3475-2 (TE436-2)Mahr-Federal Inc. (MH)



Flatness GaugePart Number: BST-2811 (TE321)

Description: Flatness gauge for steel hub flanges.

Counterweight Clamp GaugePart Number: BST-2812 (TE60)

Description: Gauge to locate D-1209( ) Counterweight Clamp on A10460E( ) Composite Blade.

Supersedes: BG-3445

TPI-1

65A

-BS

T-28

12TP

I-AP

S63

30

TPI-A

PS

6331




Clamp Nut WrenchPart Number: BST-2813 (TE142)

Description: Wrench to hold A-1373 Clamp Nut while torquing A-1372 Bolt.

Supersedes: B-2813

Outboard Clamp Bolt

A-1372

Standard 12 point Socket

Special Wrench

BST-2813

Spinner Mounting Plate BenderPart Number: BST-2823 (TE11)(CS)

Description: Spinner mounting plate bender to achieve acceptable deice slip ring runout.

Supersedes: B-2823

TPI-B

ST2

813

TPI-B

ST2

823



TemplatePart Number: BST-2825 (TE131)

Description: Template to check minimum wall thickness of T10176( ) Blade bore.

Supersedes: B-2825

AP

S-4

88

Spring Compressor AssemblyPart Number: BST-2826 (TE30)

Description: Spring compressor to compress or decompress the feathering spring for propeller assembly or disassembly on propeller model HC-E2Y( )-2( ).

Components: 1 AST-2827 (TE282) Spring Compressor Bolt 2 BST-2828 (TE283) Spring Compressor Slide

1

2

TPI-B

ST2

826




Spring Compressor AssemblyPart Number: BST-2826-1 (TE31)

Description: Spring compressor to compress or decompress the feathering spring for propeller assembly or disassembly on propeller model number

HC-E2Y( )-2( ).

Components: 1 AST-2827-1 (TE284) Spring Compressor Bolt 2 BST-2828 (TE283) Spring Compressor Slide

1

2

Torque Wrench AdapterPart Number: BST-2837 (TE6) (Includes TE385 and TE386)

Description: Installation of the pitch change rod in compact aluminum -2 propellers. Used with standard 1/2 inch square drive torque wrench.

Components: 1 . . . .BST-2837+1+3 (TE385) Modified Socket

2 . . . .BST-2837+2 (TE386) Anti-Rotation Pin

Supersedes: BT-2837

AP

S62

59

TE385TE386

BS

T282

6A



Probe SupportPart Number: BST-2847 (TE128)

Description: Probe support to ensure accurate contact of probe to blade surface during Eddy Current Inspection.

Supersedes: BT-2847

Assembling ToolPart Number: BST-2853 (TE9)

Description: Tool to assemble and disassemble the Feather Assist Spring Assembly on the compact aluminum -2 propeller. Used with AST-2981 (TE319) Assembly Guide.

Components: 1 B-3368 (TE387) 5/16-24 Hex Nut 2 BST-2850 (TE287) Threaded Rod 3 AST-2852 (TE288) Drilled Washer 4 BST-3152 (TE289) Thrust Bearing (supersedes GT-3) 5 BST-3151 (TE290) 5/8 Hex Nut 6 AST-2851 (TE291) Guide Washer 7 A-3204 (TE388) 5/16-24 Set Screw

5 6 2 3

4

1

7

TPI-B

ST2

847

TPI-B

ST2

853




Torque WrenchPart Number: BST-2860 (TE150)

Description: Wrench to tighten and torque mounting bolts on “K”, "R", or “L” flange propellers. Used in conjunction with a standard 1/2 inch square drive torque wrench.

Supersedes: BST-2835 and BT-2860

Pilot Tube PullerPart Number: BST-2876 (TE107)

Description: This part number may be used to order the drawing of the pilot tube puller for local fabrication. Puller to remove pilot tubes from steel hub propellers. Used in conjunction with DT-336 (TE53) or customer supplied fixture.

Supersedes: CST-2831

TPI-B

ST2

860

TPI-B

ST2

876



Plug-Lifting RingPart Number: BST-2884 (TE113)

Description: Ring to thread into pitch change rod of turbine propellers for lifting and moving.

Spring Compressor BasePart Number: BST-2890 (TE488) BST-2891 (TE488-1) BST-2894 (TE488-2) 106885 (TE488-3)

Description: Spring Compressor Base is to be used in conjunction with CST-2914 (TE59) Spring Compressor Fixture. Refer to CST-2914 (TE59) to determine which Spring Compressor Base (TE488-[ ]) to use with Spring Assembly type.

TPI-B

ST2

884

TPI-J

M-0

0018

8

(TE488) (TE488-1) (TE488-2) (TE488-3)




Piston FixturePart Number: BST-2892 (TE54) HC-B3( )30-2E BST-2892-1 (TE55) ALL #20 Spline BST-2892-2 (TE56) HC-B3( )30-2B

Description: Fixture to balance propellers. Used with some models of Marvel Manufacturing Company balancers.

NOTE: For left hand propeller, add L to dash number of fixture.

Supersedes: BSK-274

Spring Compressor RetainerPart Number: BST-2895 (TE489) BST-2896 (TE489-1) BST-2897 (TE489-2) BST-2899 (TE489-3) 106884 (TE489-4)

Description: Spring Compressor Retainer is to be used in conjunction with CST-2914 (TE59) Spring Compressor Fixture. Refer to CST-2914 (TE59) to determine which Spring Compressor Retainer (TE489-[ ]) to use with Spring Assembly type.

TPI-B

ST2

892

TPI-J

M-0

0018

9

(TE489) (TE489-1) (TE489-2) (TE489-3) (TE489-4)



TPI-B

ST2

908

Spring Compressor Guide RodPart Number: BST-2902 (TE490) BST-2903 (TE490-1) BST-2904 (TE490-2) BST-2905 (TE490-3) BST-2907 (TE490-4)

Description: Spring Compressor Guide Rod is to be used in conjunction with CST-2914 (TE59) Spring Compressor Fixture. Refer to CST-2914 (TE59) to determine which Spring Compressor Guide Rod (TE490-[ ]) to use with Spring Assembly type.

Piston FixturePart Number: BST-2908 (TE57)

Description: Fixture to balance propeller models ( )HC-A3VF-4 and HC-B3WF-4. Used with some models of Marvel Manufacturing Company balancers.

Supersedes: BSK-484

TPI-B

ST2

902




TPI-T

I-165

004

Piston Nut WrenchPart Number: SC046 (SO) (TE144) SC058 (SO) (TE144-1) (supersedes TE145)

Description: SC046 wrench (TE144) is used to tighten A-880-1 piston nut on a steel hub turbine propeller. Customer procured. SC058 wrench (TE144-1) is used to remove A-880-2A piston nut on a steel hub turbine propeller. Customer procured.

Supersedes: B-842, B-842-1, BST-2911, BST-3911-1



Building Buck ComponentsPart Number:BST-2912 (TE125) Building Buck Components, includes items 1 through 9 listed belowItem Number Part Number Description 1 .................BST-2912+ (TE125-1) Spindle Base; Supersedes: B-843-2 (Includes TE85) 2 .................BST-2912-1 (TE124) Flanged Hub Spindle (Includes TE4)

Supersedes: BST-2812 3 .................BST-2912-2 (TE122) #20 Spline Spindle; not shown 4 .................BST-2912-3 (TE123) #30 Spline Spindle; not shown 5 .................BST-2912-4 (TE4) Adapter Ring; Permits mounting of “N” flange

propellers 6 ..................BST-2912-9 (TE2) Adapter; Permits mounting of “A” flange single

acting propellers 7 .................BST-2912-11 (TE85) Stop Pin; not shown

Also available as necessary (not a part of BST-2912 (TE125):BST-2912-10 (TE80) “C” Flange Spindle; allow mounting of “C” flange HD-E6C-3 propeller;

not shownBST-2912-17 (TE433) “A” Flange Spindle; allow mounting of “A” flange HC-E5A-2 propeller;

not shownBST-2912-19 (TE536) “H”, “T”, “Q”, and “G” Flange Spindle; allow mounting of “H”, “T”, “Q”,

and “G” flange propellers; shown on page 4-148 of this manualBST-2912-22 (TE550) “F” Flange Bantam Adapter Ring; shown on page 4-153 of this manualDescription: Spindle mounts to propeller assembly table CST-2901(-) (TE129) to permit

pressurizing of propeller to change pitch. Also permits rotating of the propeller.

BST-2912+Spindle Base

AP

S-5

46

BST-2912-1Flanged Hub

Spindle

BST-2912-4Adapter Ring

BST-2912-9Adapter




Drill FixturePart Number: BST-2920 (TE51)

Description: Fixture to modify C-3201 Piston for installation of external feather stop.

AP

S-1

75

Torque Wrench AdapterPart Number: BST-2921 (TE153)

Description: Standard length wrench to remove, install and torque cylinders on aluminum hub propellers.

Supersedes: BST-2801

Part Number: BST-2921-1 (TE153)

Description: Short length wrench to remove, install and torque cylinders on aluminum hub propellers.

TPI-B

ST2

920



Modified Deep Well SocketPart Number: BST-2922 (TE120)

Description: Modified socket to remove, install and torque piston mounting nuts on light-weight turbine propellers.

PitchChange

Rod

Modified Deep WellSocket No. BST-2922

Piston

AP

S-1

52

Dummy Pitch Change RodPart Number: BST-2932 (TE298)

Description: Used during assembly of the HC-A6A-3 propeller.

TPI-B

ST2

932




Shot Peen PlugPart Number: BST-2938 (TE87)

Description: Plug to mask the blade bore prior to shot peening on “Y” shank blades.

Piston Installation SocketPart Number TE Number Description

BST-3067 TE228 Modified socket to install and remove piston on D-6071 and D-494 pitch change rods.

BST-3067+3 TE228-1 Modified socket to install and remove piston on D-3657 and D-7412 pitch change rods.

TPI-B

ST2

938

TPI-B

ST3

067



Shot Peen PlugPart Number: BST-2939N (TE89)

Description: Plug to mask the blade bore prior to shot peening on “M” and “T” shank blades, with “N” modifications.


Description: Plug to mask the blade bore prior to shot peening on “E” shank blades.

TPI-B

ST2

939

TPI-B

ST2

940





Description: Plug to mask the blade bore prior to shot peening on “W” shank blades.

Shank Protection CapPart Number: BST-2942 (TE13) “T,” “S” and “M” Shanks BST-2943 (TE14) “V,” “MV”, “N” and “X” Shanks BST-2944 (TE15) “W,” “R,” “Z” and “P” Shanks BST-2945 (TE16) “D” and “Y” Shanks

Description: Cap to protect blade shank and bore during shipping and storage. BST-2942 is shown.

TPI-B

ST2

941

TPI-B

ST2

942




Description: Plug to mask the blade bore prior to shot peening on “P” and “Z” shank blades.

Bushing PullerPart Number: BST-2947 (TE101)

Description: Puller to remove A-1347 and A-1309 Bushings. Used in conjunction with customer supplied hydraulic or pneumatic puller.

TPI-B

ST2

946

TPI-B

ST2

947




Bearing PullerPart Number: BST-2948 (TE102)

Description: Puller to remove A-127, A-127-1, and A-1497 bearings. Used in conjunction with customer supplied hydraulic or pneumatic puller.


Description: Puller to remove bearings from “M,” “S,” “T” and “W” shanks. Used in conjunction with a customer supplied hydraulic or pneumatic puller.

TPI-B

ST2

948

TPI-A

PS

0494

A




Description: Puller to remove bearings from “M” and “T” shanks. Used in conjunction with a customer supplied hydraulic or pneumatic puller.

TPI-J

M-0

0019

1


Description: Puller to remove bearings from “D,” “Y” and “V” shanks.

Supersedes: CST-2838

TPI-A

PS

0494

B




Pitch Angle Stop PlugPart Number: BST-2958 (TE86)

Description: Plug to block the end of the pitch change rod to allow actuation of the propeller on the bench.

Hoist Ring ComboPart Number: BST-2958L (TE62)

Description: Combination tool to lift and move propellers. Also, to seal the end of pitch change rods and actuation of propellers on the bench.

TPI-B

ST2

958

TPI-B

ST2

958L



Alignment Check RodPart Number: BST-2959 (TE114)

Description: Rod to check concentricity of the inner threads of the B-3018 or B-1948 Rod.

Supersedes: B-1509

Digital ProtractorPart Number: BST-2960-3 (TE97)

Description: Protractor to measure blade angles. May be used to check angles with propeller installed on engine. Protractor includes protractor case.

Supersedes: BST-2960-1, BST-2960-2, BST-2820, PE 105 (TE96), 799200105 (TE96), and CST-2880

NOTE: Locally procured and calibrated bubble protractor accurate to within 0.1 degree may be used and is considered equivalent.

Protractor Case

TPI-B

ST2

960

TPI-A

PS

0336

TPI-B

ST2

959




Thickness GaugePart Number: BST-2964 (TE61)

Description: Gauge to inspect thickness of 13/4 I.D. on M10876 Blade.

Ream FixtureDescription: Fixture is to locate and drill spinner support plates.

Part Number: Description SupersedesBST-2966 (TE181) C-3733 “A” Flange, 5 Way BT-2723BST-2966-3 (TE182) C-3003-1, 3 Way BST-2836, CT-1472BST-2966-4 (TE183) C-3404, 4 Way CT-1482BST-2966-5 (TE184) C-4011-5, 5 Way BST-2848

TPI-B

ST2

966

TPI-B

ST2

964



Drill JigPart Number: BST-2982 (TE75)

Description: Drill jig for “N” flange slimsert installation.

Drill JigPart Number: BST-2983 (TE76)

Description: Drill jig for “F” flange slimsert installation.

TPI-B

ST2

983

TPI-B

ST2

982




Alignment Check RodPart Number: BST-2984 (TE115)

Description: Rod to check concentricity of internal threads of D-494 Pitch Change Rod.

Bearing Installation ToolPart Number TE Number Description

BST-2985 TE64 Tool to install the blade alignment bearings in T and M shank blades with N modification. Used in conjunction with customer supplied hydraulic or pneumatic press.

BST-2985-1 TE64-1 Tool to install the blade alignment bearings in R and W shank blades with N modification. Used in conjunction with customer supplied hydraulic or pneumatic press.

BST-2985 BST-2985-1

TPI-B

ST2

984

TPI-A

PS

0744



Thread Insert Removal ToolPart Number: Description:

BST-3019 (TE112) Tool to remove B-1243 threaded staked insert.

BST-3019-3 (TE112-1) Tool to remove B-1243-1 threaded staked insert.




Blade Assembly Support StandPart Number: BST-3024 (TE126)

Description: Stand to support blade in hub during HD-E6C-3 or HC-E4N-3A propeller assembly.

TPI-B

ST3

024

TPI-B

ST3

019




Bearing PressPart Number: BST-3026-1 (TE238) 1.000 inch O.D. BST-3026-2 (TE239) 1.500 inch O.D. BST-3026-3 (TE240) 1.625 inch O.D.

Description: Press used to install bearings into bearing carriers or housings during assembly of HD-E6C-3 propeller or PCU.

Modified CrowfootPart Number: BST-3027 (TE40)

Description: Modified 15/16 inch, 3/8 inch drive crowfoot wrench.

TPI-B

ST3

026

TPI-B

ST3

027




Description: Modified 113/16 inch, 3/8 inch drive crowfoot wrench.


Description: Modified 13/4 inch, 3/8 inch drive crowfoot wrench used during assembly and disassembly of HD-E6C-3 propeller.

TPI-B

ST3

031

TPI-B

ST3

030




Open End WrenchPart Number: BST-3032 (TE143)

Description: Modified 13/4 inch open end wrench.


Description: Modified 17/16 inch crowfoot adapter to remove, install and torque pitch change rod or hydraulic assembly into pitch change fork of HD-E6C-3 propeller. If propeller has been subjected to pitch lock, use BST-3044.

TPI-B

ST3

032

TPI-B

ST3

033



AdapterPart Number: BST-3035 (TE3)

Description: Adapter to remove or install the front bearing nut in the HD-E6C-3 propeller.

Piston Installation ConePart Number: BST-3036 (TE63)

Description: Cone used to compress O-rings and seals installed on PCU servo piston to allow ease of installation into PCU servo column.

TPI-B

ST3

036

TPI-B

ST3

035




Aft Control Spring CompressorPart Number: BST-3037 (TE74)

Description: Tool to be used in conjunction with customer supplied press to push against spacer in order to compress aft spring of HD-E6C-3 propeller. This allows installation of spacer retaining ring.

Control Rod Alignment ToolPart Number: BST-3038 (TE26)

Description: Used to re-align the control rod to control valve in the HD-E6C-3 propeller.

TPI-B

ST3

037

TPI-B

ST3

038




Description: Puller to remove pitch lock bearing and carrier from pitch lock bearing housing of HD-E6C-3 propeller.

Rigging PinPart Number: BST-3041 (TE84)

Description: Rigging pin, 3/16 inch diameter, to hold PCU and CSU power and condition levers in the correct position for rigging. (Two required.)

TPI-B

ST3

041

TPI-B

ST3

039




Clamp WrenchPart Number: BST-3044 (TE141)

Description: Wrench to remove pitch change rod or hydraulic assembly from pitch change fork of HD-E6C-3 propeller after pitch lock.

PullerPart Number: BST-3045 (TE98)

Description: Puller to remove bearings from pitch change brackets, O-ring plugs from extended hub compact propellers, etc.

TPI-B

ST3

044

TPI-B

ST3

045



Threaded Insert Installation ToolPart Number: Description: Supersedes:

BST-3047 (TE68) Tool to install B-1243 threaded staked insert. AT-2422, KHT9000-9

BST-3047-1 (TE68-9) Tool to install B-6143 threaded staked insert.BST-3047-2 (TE68-8) Tool to install B-6143-4 threaded staked insert.BST-3047-3 (TE68-3) Tool to install B-6143-4H threaded staked insert.BST-3047-4 (TE68-4) Tool to install B-6143-5 threaded staked insert.BST-3047-5 (TE68-5) Tool to install B-6143-7 threaded staked insert.BST-3047-6 (TE68-6) Tool to install B-6143-8 threaded staked insert.BST-3047-7 (TE68-7) Tool to install B-6143-8H threaded staked insert.BST-3047-8 (TE68-1) Tool to install B-1243-1 threaded staked insert.

Transfer Tube and Plug Removal/Installation ToolPart Number: BST-3048 (TE320)

Description: Installation of transfer tube and removal of transfer tube and plug in HD-E6C-3 propeller.

TPI-B

ST3

048A

TP

I-BS

T304

8BTP

I-BS

T304

7




Chip Detector FittingPart Number: BST-3050 (TE492)

Description: Chip Detector Fitting used with DST-3049-( ) (TE318) Ground Hydraulic Power Unit.

Chip Detector Fitting CoverPart Number: BST-3051 (TE493)

Description: Cover for BST-3050 Chip Detector Fitting on DST-3049-( ) Ground Hydraulic Power Unit.

TPI-B

ST3

050

TPI-B

ST3

051



PCU Manifold Installation ToolPart Number: BST-3054 (TE72)

Description: Tool used to align and install PCU manifold insert into PCU manifold/servo column.

PCU Bearing Installation ToolPart Number: BST-3055 (TE185) For B-6133-1 Bearing BST-3055-1 (TE186) For B-6133-2 Bearing

Description: Tool used in conjunction with customer supplied press to install roller bearings into PCU manifold.

TPI-B

ST3

055

TPI-B

ST3

054




PCU Bushing Installation ToolPart Number: BST-3056 (TE70)

Description: Tool used in conjunction with customer supplied press to install oil lite bushings into PCU manifold.

PCU Bushing Installation ToolPart Number: BST-3057 (TE71)

Description: Tool used in conjunction with customer supplied press to install oil lite bushings into PCU manifold.

TPI-B

ST3

056

TPI-B

ST3

057



Shot Peen Masking ToolPart Number: BST-3060 (TE118), BST-3060-2 (TE118-1)

Description: BST-3060: Screw to mask 1/2-28 helicoil holes during shot peening.

BST-3060-2: For 3-way Bantams only, screw to mask 1/2-28 helicoil holes during shot peening.

Screw DriverPart Number: BST-3060-1 (TE46)

Description: Screw driver to drive BST-3060 Screw.

BST-3060 BST-3060-2

TPI-B

ST3

060A

TPI-B

ST3

060




Press ToolPart Number: BST-3061 (TE308)

Description: Used to press split bearings in steel hub propellers.

Supersedes: BT-222-1

Press ToolPart Number: BST-3062 (TE309)

Description: Used to press split bearings in steel hub propellers.

Supersedes: BT-222

TPI-B

ST3

061

TPI-B

ST3

062



BST-3064-2HC-B( )( )( )

(TE243)

BST-3064-3HC-9( )2( )-( )

(TE244)

BST-3064-4HC-A( )( )( )HC-D( )( )( )

(TE245)

BST-3064-5HC-8( )X( )-( )

(TE246)

BST-3064-1 (TE242)

Pilot Tube Installation Tool KitDescription: Tool set contains various spacer adapters. Refer to TE52 for the fixture to

be used with customer procured hydraulic press.

Kit Part Number:

BST-3064 (TE241) BST3064-1 (TE242) can only be used with a hydraulic press that accepts a ram adapter that is 0.75 inch (19.0 mm) diameter by 1.25 inches (31.7 mm) long. For other hydraulic presses, the ram adapter is customer procured.

Kit with the Pilot Tube Installation Tool includes: Components 1 BST-3064-1 (TE242) Pilot Tube Installation Tool

(May be purchased separately.) 2 ...BST-3064-2 (TE243) Pilot Tube Positioner & Stop 3 ...BST-3064-3 (TE244) Pilot Tube Positioner & Stop 4 ...BST-3064-4 (TE245) Pilot Tube Positioner & Stop 5 ...BST-3064-5 (TE246) Pilot Tube Positioner & Stop

Supersedes: B-844

BST-3064A (TE241-1) Kit without the Pilot Tube Installation Tool includes: Components 1 ...BST-3064-2 (TE243) Pilot Tube Positioner & Stop 2 ...BST-3064-3 (TE244) Pilot Tube Positioner & Stop 3 ...BST-3064-4 (TE245) Pilot Tube Positioner & Stop 4 ...BST-3064-5 (TE246) Pilot Tube Positioner & Stop

TPI-B

ST3

0641

TP

I-BS

T306

42

TPI-B

ST3

0643

TP

I-BS

T306

44

TPI-B

ST3

0645




Chamfering ToolPart Number: BST-5845 (TE50)

Description: A six fluted, 45 degree chamfering tool used to chamfer grease fitting holes in aluminum hubs (reference Hartzell Service bulletin No. 165E or subsequent revision).

Blade Shot Peen Plug Removal ToolPart Number: BST-3065 (TE110)

Description: Tool to remove shot peen plugs.

TPI-B

ST3

065

TPI-B

ST-

5845



Transfer Tube O-ring Installation ToolPart Number: BST-10001 (TE69)

Description: Tool to protect O-ring when it is installed over the HD-E6C-3 propeller oil transfer tube.

Beta Valve Freeze SleevePart Number: BST-10002 (TE117)

Description: Installation of beta valve assembly in the PCU.

TPI-B

ST1

0002

TPI-B

ST1

0001




Modified Deep Well SocketPart Number: BST-10004 (TE251)

Description: Used in the assembly and disassembly of HD-E6C-3 propeller.

Flight Idle Set FixturePart Number: BST-10003 (TE136)

Description: Fixture to set PCU piston indicating rod at the pre-set flight idle position.

TPI-B

ST1

0003

TPI-B

ST1

0004



Beta Switch TesterPart Number: BST-10005 (TE157)

Description: Test box to simulate the cockpit beta light when rigging the PCU beta light switch during PCU assembly. To be used in conjunction with BST-10006 Rigging Cover.

Rigging CoverPart Number: BST-10006 (TE58)

Description: Cover used to actuate the PCU beta light switch at pre-set position to assist in beta light switch rigging. To be used in conjunction with BST-10005 Beta Light Switch Test Box.

STAND-BY BETA

ON

OFF

BST-10005HARTZELL

TPI-B

ST-

1000

5TP

I-BS

T-10

006A

TPI-B

ST-

1000

6B




Strap WrenchPart Number: 100923 (TE148-1)

Description: Wrench to install/remove feathering spring.

Supersedes: BT-461 (TE148)

Threaded Headless PinsPart Number: BST-10007 (TE159)

Description: These pins are threaded into the hub's forward mounting ring to hold it in the correct position for:

1) Hydraulic unit mounting during HD-E6C-3 propeller assembly (four required).

2) Cylinder mounting during the HC-E5A-2 propeller assembly (2 required).

TPI-B

ST1

0007

TPI-1

0092

3



TPI-A

PS

0189

Press Tool BST-3061 (TE308) or BST-3062 (TE309) to pull bearing retaining ring into position

Retention Bearing PullerPart Number: BT-223 (TE108)

Description: Puller to remove and install the bearing retaining ring on steel hubs. Used in conjunction with BST-3061 (TE308) press tool and BST-3062 (TE309) press tool. Use adaptor rings as listed.

Adaptor Rings: BT-223+9 (TE108-1) (CS) Adaptor ring used when removing or installing the A-1852 bearing retaining ring. Use with BST-3062 (TE309) press tool.


BT-223+10 (TE108-2) (CS) Adaptor ring used when removing or installing the A-972 bearing retaining ring. Use with BST-3061 (TE308) press tool.


Bearing Retaining Ring

Adaptor BT-223+9 (TE108-1) or BT-223+10 (TE108-2)




Shot Peen Tube AssemblyPart Number: BT-1271-1,2 (TE137)

BT-1271-1 Fine Threads

BT-1271-2 Coarse Threads

Description: Adapter assembly to shot peen blade balance bores. Used with CT-1311 (TE12).

Supersedes: BT-1271

Shot Peen Gun (TE379) (not included)

Shot Peen Tube Assembly (TE137)

Shot Nozzle Unit (TE494) (not included)

Shot Nozzle UnitPart Number TE Number Length

BT-1271-4 (TE494) 1.95 inches (49.5 mm) BT-1271-5 (TE494-1) 3.34 inches (84.8 mm) BT-1271-6 (TE494-2) 4.72 inches (119.8 mm) BT-1271-7 (TE494-3) 6.10 inches (154.9 mm) BT-1271-8 (TE494-4) 10.10 inches (256.5 mm)

Description: Used with Shot Peen Cabinet CT1311 (TE12), Shot Peen Gun 02643 (TE379), Shot Peen Tube Assembly BT-1271(-1,or-2) (TE137)

Length

TPI-B

T127

1TP

I-BT-

1271

-4_8



Almen Strip FixturePart Number: 104381 (TE49)

Description: Fixture to confirm shot intensity in the lead hole of a blade.

Supersedes: BT-1312

TPI-T

I-165

006

TPI-T

I-165

007

TPI-A

PS

-180

A

Shot Peen CabinetPart Number: CT-1311 (TE12) (CS)

Description: This part number may be used to order the drawing of the shot peen cabinet for local fabrication. Cabinet to house and support the blade during lead hole shot peening. Used with BT-1271 (TE137), BT-1312 (TE49), BT-1271-( ) (TE494-[ ])and 02643 (TE379).




Eddy Current Probe UnitDescription: Probe for Eddy Current inspection of blade balance hole.

Part Number: BT-1313 (TE95) No longer available from Hartzell Propeller Inc. Order from vendor (See below)

Superseded by Olympus NDT Inc. Part Number BT-1313(-)( ) (TE95)

Part Number: Olympus NDT Inc. Part Number BT-1313(-)( ) (TE95)

NOTE: There are three versions of the eddy current probe unit available from Olympus NDT Inc. Refer to the chart.

Supersedes: BT-1313 (Hartzell Part Number)

Vendor: Olympus NDT Inc. (OL)

Probe (included)

Olympus NDT Inc. Part Number Connector Type

BT-1313 1/4" HeadphoneBT-1313-1 MicrodotBT-1313-2 Triax Fischer/Lemo

1/4" Headphone Microdot Triax Fischer/Lemo

Connector Types

Probe Collar (included)

Connector (see chart)

TPI-B

T131

3



Floating ReamerPart Number: BT-1465-1 (TE207) 0.766 (19.45 mm) diameter ball nose

BT-1465-3 (TE207-1) 0.758 (19.25 mm) diameter ball nose

BT-1465-2 (TE208) 0.781 (19.83 mm) diameter ball nose BT-1465-4 (TE208-1) 0.773 (19.63 mm) diameter ball nose

Description: Reamer to repair a blade balance hole.

Floating reamer holder not supplied by Hartzell Propeller Inc.

Insert Installation ToolPart Number: BST-7588 (TE445)

Description: Used to provide a location of depth of the flange mounting inserts during the adhesive cure process.

NOTE: This part number may be used to order the drawing to allow for local fabrication.

TPI-B

T146

5-1

TI-1

65A

-BS

T-75

88




Stop AdapterPart Number: BST-3066-2 (TE311)

Description: Adapter to push pilot tubes deeper into the hub in order to remove with less force.

Peening ToolPart Number: BST-3068 (TE247)

Description: Tool for peening A-2245-(1) bushings in aluminum hubs.

TPI-B

ST3

066

TPI-B

ST3

068



TE315

Eddy Current Probe

AP

S-2

079

3009

.TIF

PCU Bearing Seat SanderPart Number: BST-2970 (TE274)

Description: Tool for sanding the O.D. bearing seat surface on Propeller Control Unit.

Eddy Current FixturePart Number: BST-3069 (TE315)

Description: Eddy current probe support fixture for inspecting "X" and "V" shank double shoulder aluminum propeller blades. (Does not include probe. Standard 1/8 inch pencil probe is recommended.)




Drill Jig (PCU)Part Number: BST-3070 (TE296)

Description: Drill jig for removing the PCU manifold plug from Propeller Control Unit.

PCU StandPart Number: BST-3071 (TE297)

Description: Stand for securing Propeller Control Unit during maintenance operations.

BS

T307

1.TI

FB

ST-

3070

.ai



Centering Tool for C-5623-2 Drive CouplingPart Number: BT-3035 (TE310)

Description: Tool for aligning the drive coupling in the PCU manifold.

E13890 Master BladePart Number: BST-3200 (TE431) - Group 0 (-100 in. oz.)

BST-10037 (TE299) - Group 1 (-5 in. oz.)

BST-10038 (TE300) - Group 2 (+100 in. oz.)

BST-10039 (TE301) - Group 3 (+180 in. oz.)

102690 (TE460) - Group 4 (+260 in. oz.)

Description: Used to balance composite blades into balance groups. Not shown. The part numbers above may be used to order the drawing of the master blade for local fabrication.

TPI-B

T303

5




Pitch Lock Roller FixturePart Number: BST-10026 (TE362)

Description: Used to compress A-5654-1 pitch lock unit to facilitate disassembly/assembly.


Description: Modified 1¼ inch, 3/8 inch drive crowfoot wrench used to adjust the pitch lock gap on the HD-E6C-3( ) propeller.

TPI-B

ST1

0015

TPI-B

ST1

0026




Description: Plug to mask the blade bore prior to shot peening on “X” shank, “X” shank modified to “V” shank, “V” shank, “V” shank blades with “N” modification and “MV” shank blades with “N” modification. Used with TE372 as required.

Shot Peen PlugPart Number: BST-3080-1 (TE372)

Description: Used with TE371 to mask the blade bore prior to shot peening on “V” shank blades with “N” modification and “MV” shank blades with “N” modification.

TPI-B

ST3

080

TPI-B

ST3

080A




T-Handle WrenchPart Number: BST-3109 (TE381)

Description: Installation of the stop screw in compact aluminum -2 propellers.

Feathering ToolPart Number: BST-3103 (TE383)

Description: Tool used to install the pitch adjustment washers and feathering stop in compact aluminum -2 propellers.

TPI-A

PS

6262

TPI-A

PS

6260



Cylinder Installation RodPart Number: BST-3104 (TE384)

Description: Tool used to spread the start lock mechanism when installing the cylinder in compact aluminum feathering propellers.

AP

S62

61

ReamerPart Number: BST-3022 (TE403) - All Compact and "H" and "Q" Bantam propeller hubs

with 1/2-20UNF studs

BST-3022A (TE403-1) - Bantam propeller hubs with 7/16-20UNF studs

Description: Used to remove adhesive from the bottom of hub mounting stud holes.

BS

T302

2





Description: Plug to mask the blade bore before shot peening “M” and “T” shank blades that do not have “N” modifications.

BS

T293

9


Description: Puller to remove bearings from "E" shanks. Used in conjunction with customer supplied hydraulic or pneumatic puller.

NOTE: Use only with bearings having a cage and a flat bottomed closed end. This puller will not work on bearings with a full complement of needles and a dimpled closed end.

BS

T295

1



Paint Mask CapPart Number: BST-3006 (TE414) diameter of "A" is 5.930 inches (15.06 cm)

BST-3158 (TE415) diameter of "A" is 6.345 inches (16.12 cm) BST-3159 (TE416) diameter of "A" is 5.745 inches (14.59 cm) BST-3160 (TE417) diameter of "A" is 5.370 inches (13.64 cm) BST-3161 (TE418) diameter of "A" is 5.875 inches (14.92 cm) BST-3162 (TE419) diameter of "A" is 5.180 inches (13.16 cm)

Description: Used to mask the cylinder attachment thread area of aluminum hubs.

"A"

TPI-B

ST3

006

TPI-B

ST3

006A




SpacerPart Number: BST-2991 (TE420)

Description: Used during assembly for set up of 2-way Hydro-Selective propellers.

BS

T299

1

Mask ScrewPart Number: BST-3081 (TE428)

Description: Screw to mask shot peen from the lubrication fitting hole in an aluminum hub.

BS

T308

1



Blade Pitch FixturePart Number: BST-3226 (TE438)

Description: Tool that attaches to the blade for blade angle check.

Probe Housing ComponentPart Number: BST-3227 (TE437)

Description: Used to support the probe of the profilometer when performing the surface finish inspection in the radius and transition areas of aluminum blade shanks. Used with AST-3475 (TE436) (MH), as necessary.

BS

T-32

27TI

-BS

T-32

26




Blade Seal Alignment ToolPart Number:

BST-3177 (TE440) For four-bladed lightweight turbine propellers

BST-3063 (TE440-1) For five-bladed lightweight turbine propellers

Description: Used during assembly to aid installation of the blade seal.

BS

T317

7

Composite Balance Tube PullerPart Number: BST-4114 (TE442)

Description: Tool to remove composite blade balance tube.

BS

T411

4



Grease Seal Pressure Test Tool (Adapter)Part Number: BT-3838 (TE443)

Description: Used with TE382 (DST-3146) Thread Gauge Airflow Kit to perform grease seal pressure test.

NOTE: Use with O-rings C-3317-010-2 and C-3317-08-2, not supplied.

BT-

3838

Grease Seal Pressure Test ToolPart Number: BT-3838-1 (TE443-1)

Description: Used with TE382 or TE382-1 Thread Gauge Airflow Kit to perform grease seal pressure test.

NOTE: BT-3838-1 (TE443-1) eliminates the need for using both the CST-3117 Probe Assembly and BT-3838 (TE443) to check grease seal pressure.

BT-

3838

-1A




Pressure Check ToolPart Number: BST-7587 (TE441) ........For K, R, L, and F flange

BST-7587-1 (TE441-1) ..For N, P, and W flange

BST-7587-2 (TE441-2) ..For Q, T, H, and G flange

BST-7587-3 (TE441-3) ..For A and B flange, except D-1066-1 hub with an A flange

BST-7587-4 (TE441-4) ..For C flange

BST-7587-5 (TE441-5) ..For a D-1066-1 hub unit with an A flange. Use with the BST-7587-3 pressure check tool.

Description: Used to perform a leak inspection after repair of the pitch change rod bore of an aluminum hub.

NOTE: This part number may be used to order the drawing to allow for local fabrication.

BS

T-75

87

TI-1

65A

-BS

T-75

87-1

BS

T-75

87-2

TI-1

65A

-BS

T-75

87-3

TI-1

65A

-BS

T-75

87-4

TI-1

65A

-BS

T-75

87-5



Stud Fixture PlatePart Number: CST-421 (TE487)

Description: A tool used when installing studs in D-flange, F-flange, N-flange, and W-flange hubs to make sure that the studs are set perpendicular to the hub flange.

CS

T-42

1TP

I-AP

S01

62

Blade Retention Components ClampPart Number: CST-2800 (TE24)

Description: Clamp to hold the blade retention components onto the blade shank for installation into the hub. Designed to fit “D” and “Y” shank blades.




Pilot Tube Assembly Tool (TE242) (*May be purchased separately.)

HydraulicPress Ram

Tool No.BST-3064-( )

(TE243 through TE246, sold separately)

Customer-procured Support Plate

Hub Pilot Tube

Endplate of Pilot Tube FixtureCST-2913

AP

S19

7-1

Pilot Tube Press FixturePart Number: CST-2913 (TE52)

Description: Fixture to securely hold the propeller hub during pilot tube installation. The press is customer procured. Press must be capable of generating up to 25 tons of force, have an adjustable press opening height, and at least 3.5 inches (88.9 mm) of stroke.

Supersedes: B-843-2

* TE242 can only be used with a hydraulic press that accepts a ram adapter that is 0.75 inch (19.0 mm) diameter by 1.25 inches (31.7 mm) long. For other hydraulic presses, the ram adapter is customer procured.



AP

S-5

45

Spring Compressor FixturePart Number: CST-2914 (TE59)

WARNING: USE EXTREME CAUTION DURING DISASSEMBLY. THE FEATHERING SPRING ASSEMBLY MAY BE PRELOADED TO OVER 2000 POUNDS FORCE.

Description: Fixture to compress the feathering spring sufficiently to allow assembly or disassembly of the spring assembly.

NOTE: This fixture is not to be used on 5 and 6 way propellers with an “E” or “A” shank. The fixture to be used for “E” shanks is CST-3016 (TE32) and the fixture for “A” shanks is customer supplied.

Supersedes: CSD-4900, C-845-2

The following tooling is required in addition to the CST-2914 Spring Compressor Fixture:Description Base Retainer Guide RodHC-E5(A,N,P)-3 106885 (TE488-3) 106884 (TE489-4) BST-2905 (TE490-3)

BST-2899 (TE489-3) (Optional)Spring Assembly Base Retainer Guide Rod831-1A BST-2894 (TE488-2) BST-2895 (TE489) BST-2907 (TE490-4)831-2 BST-2890 (TE488) BST-2899 (TE489-3) BST-2905 (TE490-3)831-3 BST-2894 (TE488-2) BST-2895 (TE489) BST-2907 (TE490-4)831-4 BST-2894 (TE488-2) BST-2895 (TE489) BST-2907 (TE490-4)831-5A, B, C BST-2894 (TE488-2) BST-2895 (TE489) BST-2907 (TE490-4)831-6 BST-2894 (TE488-2) BST-2895 (TE489) BST-2907 (TE490-4)831-7 BST-2890 (TE488) BST-2899 (TE489-3) BST-2905 (TE490-3)831-8 BST-2890 (TE488) BST-2895 (TE489) BST-2904 (TE490-2)831-9 BST-2890 (TE488) BST-2899 (TE489-3) BST-2905 (TE490-3)831-10 BST-2890 (TE488) BST-2899 (TE489-3) BST-2905 (TE490-3)831-13 BST-2891 (TE488-1) BST-2899 (TE489-3) BST-2905 (TE490-3)831-14 BST-2894 (TE488-2) BST-2895 (TE489) BST-2907 (TE490-4)831-15 BST-2891 (TE488-1) BST-2899 (TE489-3) BST-2905 (TE490-3)




Spring Compressor Fixture, ContinuedSpring Assembly Base Retainer Guide Rod831-16 BST-2890 (TE488) BST-2899 (TE489-3) BST-2905 (TE490-3)831-16A BST-2890 (TE488) BST-2899 (TE489-3) BST-2905 (TE490-3)831-17 BST-2890 (TE488) BST-2899 (TE489-3) BST-2905 (TE490-3)831-18 BST-2890 (TE488) BST-2899 (TE489-3) BST-2905 (TE490-3)831-19 BST-2890 (TE488) BST-2895 (TE489) BST-2902 (TE490)831-20 BST-2894 (TE488-2) BST-2895 (TE489) BST-2903 (TE490-1)831-21 BST-2894 (TE488-2) BST-2896 (TE489-1) BST-2903 (TE490-1)831-22 BST-2890 (TE488) BST-2896 (TE489-1) BST-2902 (TE490)831-23 BST-2894 (TE488-2) BST-2895 (TE489) BST-2902 (TE490)831-23A BST-2890 (TE488) BST-2895 (TE489) BST-2902 (TE490)831-24 BST-2890 (TE488) BST-2895 (TE489) BST-2903 (TE490-1)831-25 BST-2890 (TE488) BST-2895 (TE489) BST-2903 (TE490-1)831-26 BST-2890 (TE488) BST-2895 (TE489) BST-2903 (TE490-1)831-27 BST-2890 (TE488) BST-2895 (TE489) BST-2903 (TE490-1)831-28 BST-2894 (TE488-2) BST-2896 (TE489-1) BST-2904 (TE490-2)831-29 BST-2890 (TE488) BST-2895 (TE489) BST-2904 (TE490-2)831-30 BST-2894 (TE488-2) BST-2895 (TE489) BST-2904 (TE490-2)831-31 BST-2890 (TE488) BST-2895 (TE489) BST-2904 (TE490-2)831-33 BST-2890 (TE488) BST-2895 (TE489) BST-2904 (TE490-2)831-34 BST-2894 (TE488-2) BST-2895 (TE489) BST-2904 (TE490-2)831-35 BST-2891 (TE488-1) BST-2899 (TE489-3) BST-2905 (TE490-3)831-36 BST-2890 (TE488) BST-2895 (TE489) BST-2903 (TE490-1)831-38 BST-2894 (TE488-2) BST-2895 (TE489) BST-2904 (TE490-2)831-39 BST-2894 (TE488-2) BST-2895 (TE489) BST-2904 (TE490-2)831-40 BST-2894 (TE488-2) BST-2895 (TE489) BST-2904 (TE490-2)831-41 BST-2890 (TE488) BST-2896 (TE489-1) BST-2902 (TE490)831-42 BST-2890 (TE488) BST-2896 (TE489-1) BST-2902 (TE490)831-43 BST-2894 (TE488-2) BST-2896 (TE489-1) BST-2903 (TE490-1)831-44 BST-2890 (TE488) BST-2896 (TE489-1) BST-2903 (TE490-1)831-45 BST-2894 (TE488-2) BST-2895 (TE489) BST-2904 (TE490-2)831-46 BST-2890 (TE488) BST-2895 (TE489) BST-2903 (TE490-1)831-47 BST-2890 (TE488) BST-2895 (TE489) BST-2902 (TE490)831-48 BST-2894 (TE488-2) BST-2895 (TE489) BST-2904 (TE490-2)831-50 BST-2894 (TE488-2) BST-2895 (TE489) BST-2903 (TE490-1)831-51 BST-2894 (TE488-2) BST-2896 (TE489-1) BST-2903 (TE490-1)831-52 BST-2890 (TE488) BST-2899 (TE489-3) BST-2905 (TE490-3)831-53 BST-2894 (TE488-2) BST-2895 (TE489) BST-2907 (TE490-4)831-54 BST-2894 (TE488-2) BST-2896 (TE489-1) BST-2904 (TE490-2)831-55 BST-2890 (TE488) BST-2896 (TE489-1) BST-2903 (TE490-1)831-56 BST-2890 (TE488) BST-2897 (TE489-2) BST-2902 (TE490)831-57 BST-2890 (TE488) BST-2895 (TE489) BST-2903 (TE490-1)831-58 BST-2890 (TE488) BST-2896 (TE489-1) BST-2903 (TE490-1)831-59 BST-2890 (TE488) BST-2895 (TE489) BST-2904 (TE490-2)



Spring Assembly ToolPart Number: BST-2855 (TE627)

Description: Assembling tool for the HC-E3YR-7( )F propeller.

Part Number Description Quantity

A-3204 (TE388) Screw, Set, 5/16-24 1

AST-2851 (TE291) Guide Washer 1

BST-2850-1 (TE628) Threaded Rod 1

BST-3151 (TE290) Nut, Hex 5/8-11 1

BST-3152 (TE289) Bearing, Thrust 1

TPI-1

65A

-BS

T-28

55

Threaded Rod BST-2850-1 (TE628)

5/16-24 Set ScrewA-3204 (TE388)

Guide WasherAST-2851 (TE291)

Thrust BearingBST-3152 (TE289)

5/8-11 Hex NutBST-3151 (TE290)




Balance ArborPart Number: CST-2919 (TE8)

Description: Used to determine the location of the static balance weights on a completed propeller assembly. Used with customer supplied balance units. Works with 2 to 5 bladed propellers with “F”, “K”, “L”, “N” and “R” flanges.

Supersedes: CT-2210 and CSK-155

Includes2 Flanges

CS

T-29

19

Spring Compressor AssemblyPart Number: BST-2826-2 (TE625)

Description: Spring compressor to compress or decompress the flange half spring for the C-clip and split keeper removal on propeller model HC-E3YR-7( )F.

Components: 1 AST-2827-1 (TE284) Spring Compressor Bolt

2 BST-2828-1 (TE626) Slide

TPI-1

65A

-BS

T-28

26-2

, TP

I-165

A-B

ST-

2826

-2-B

1

2



Optical Comparator OverlayPart Number: CST-2923 (TE18) “D” and “Y” Shanks CST-2924 (TE19) “X,” “V” and “V with N modification” Shanks CST-2925 (TE20) “Z,” “W,” “T” and “S” Shanks CST-2926 (TE21) “M,” “R” and “P” Shanks CST-2989 (TE22) “E” Shank CST-10050 (TE373) "MV" Shank 106415 (TE569) "D" Outer Shank 106554 (TE595) "C" Shank 106784 (TE614) "N" ShankDescription: A 14 inch (355.6 mm) clear overlay to check the condition and repairability

of a blade retention radius. Used with a locally procured optical comparator. For the current revision level of each overlay, refer to Hartzell Propeller Inc. Aluminum Blade Overhaul Manual 133C (61-13-33) or Hartzell Propeller Inc. Composite Propeller Blade Maintenance Manual 135F (61-13-35), as applicable.

Blade Retention Components ClampPart Number: CST-2929 (TE25)

Description: Clamp to hold the blade retention components onto the blade shank for installation into the hub. Designed to fit “A” and “E” shank blades, and “N” shank composite blades in lightweight compact hubs.

TPI-A

PS

0162

TPI-C

ST2

923




TPI-1

65A

-CS

T-29

87, C

ST-

2987

+8, C

ST-

2987

+9

CST-2987+8 (4 pieces included)

CST-2987+9 (3 pieces included)

CST-2987

CST-2987+13 or CST-2987+16

CST-2987+7 or CST-2987+15

106804

Beta System PullerPart Number: CST-2987 (TE100)



Beta System Puller, ContinuedPart Number: CST-2987 (TE100)Supersedes: CST-2834, CST-2834-( )Description: Puller to compress the beta system on all -3 turbine propellers that uses

various types of adapters to gain access to the propeller mounting bolts for propeller removal and installation.

The following replacement components are available individually: Item Number Part Number Description 1 . . . . . . . . . . . . . CST-2987+8 Finger Adapter 2 . . . . . . . . . . . . . CST-2987+9 Finger Adapter 3 . . . . . . . . . . . . . CST-2987+13 Adapter Nut 4 . . . . . . . . . . . . . CST-2987+7 Threaded Shaft 5 . . . . . . . . . . . . . CST-2987+15 Threaded Rod 6 . . . . . . . . . . . . . CST-2987+16 Adapter

NOTE 1: CST-2987 includes items 1 through 6 listed above and the 106804 plate-kit listed below.

NOTE 2: Adapter Nut CST-2987+13 is used with Threaded Shaft CST-2987+7 and Adapter CST-2987+16 is used with Threaded Rod CST-2987+15.

Plate-Kit 106804 (TE615) For puller to clock around the pitch locks, use plate-kit 106804 with the beta

system puller CST-2987. Item Number Part Number Description 1 . . . . . . . . . . . . . 106788 Plate 2 . . . . . . . . . . . . . standard Nut, 5/16-24 3 . . . . . . . . . . . . . standard Bolt, 5/16-24 x 3/4, Hex Head




Portable Spring CompressorPart Number: CST-3016 (TE32)

Description: Spring compressor for feathering spring assembly during assembly or disassembly of lightweight turbine “E” shank 5 and 6 Way propellers.

Dual Acting Propeller Assembly Table Add-on PackagePart Number: CST-3021 (TE10)

Description: An add-on package compatible with CST-2901(-) propeller assembly tables. Permits the ability to control HD-E6C type propellers. The add-on package includes a mounting bracket, electric actuator, push button control box, BST-2912-10 "C" flange spindle adapter, and the hardware to interface with the propeller. Requires 105-125V AC, 50/60 Hz or 208-245V AC, 50/60 Hz source. Hole drilling and some assembly required.

CS

T-30

21.A

ITP

I-CS

T301

6



Dual Acting Propeller Assembly Tool KitPart Number: CST-3028 (TE78)

Description: Tools required for disassembly and reassembly of HD-E6C-3 propeller and PCU.

Qty. Vendor Hartzell P/N Vendor P/N Description

1 HP BST-3027 (TE40) n/a Modified Crowfoot 1 HP BST-3030 (TE41) n/a Modified Crowfoot 1 HP BST-3031 (TE42) n/a Modified Crowfoot 1 HP BST-3033 (TE43) n/a Modified Crowfoot 1 HP BST-3035 (TE3) n/a Adapter 1 HP BST-3036 (TE63) n/a Piston Installation Cone 1 HP BST-3037 (TE74) n/a Aft Control Spring Compressor 1 HP BST-3038 (TE26) n/a Control Rod Alignment Tool 1 HP BST-3039 (TE99) n/a Bearing Puller 2 HP BST-3041 (TE84) n/a Rigging Pin 1 HP BST-3044 (TE141) n/a Clamp Wrench 1 HP BST-3045 (TE98) n/a Puller 1 HP BST-3054 (TE72) n/a PCU Manifold Installation Tool 1 HP BST-3055 (TE185) n/a PCU Bearing Installation Tool 1 HP BST-3055-1 (TE186) n/a PCU Bearing Installation Tool 1 HP BST-3056 (TE70) n/a PCU Bushing Installation Tool 1 HP BST-3057 (TE71) n/a PCU Bushing Installation Tool 1 HP BST-10002 (TE117) n/a Beta Valve Freeze Sleeve 1 HP BST-10003 (TE136) n/a Flight Idle Set Fixture 1 HP BST-10004 (TE251) n/a Deep Well Socket 1 HP BST-10005 (TE157) n/a Beta Light Switch Test Box 1 HP BST-10006 (TE58) n/a Rigging Cover 4 HP BST-10007 (TE159) n/a Threaded Headless Pins 1 SO (TE176) APS351 Adjustable Spanner Wrench, 1/8 Pin 1 BH 9943BLX13 (TE261) BLX 13 Ball Head Hex. Wrench Set 2 LS 9943EN1901 (TE262) EN1 901 Propeller Sling, 1 inch x 3 feet

1 SO 9943FS081 (TE109) GFS081 Socket, 6 Point, ¹/8 inch, 3/8 Drive

1 SO 9943MU121 (TE166) GTMU121 Universal Socket, 12 Point, 3/8 inch, 1/4 Drive 1 SO (TE192) GFC48A Crowfoot Wrench, Open End with Side Lock Hole, 11/2 inch, 3/8 Drive 1 SO (TE202) GSF161 Deep Well Socket, 12 Point, 1/2 inch, 3/8 Drive 1 SO 9943FC012 (TE214) GFC012 Crowfoot Wrench, Open End, 3/8 in 2 SO 994313309 (TE229) GFA4A Socket Driver, 5/32 Hex. Head, 3/8 Drive 1 SO (TE248) GF10M Breaker Bar, 3/8 Drive




Dual Acting Propeller Assembly Tool Kit, Continued Qty. Vendor Hartzell P/N Vendor P/N Description

1 SO (TE249) GV01820 Open End Wrench, Std Length, 9/16 - 5/8 in

1 SO 994313308 (TE255) GFX1 Extension, 2 inches, 3/8 Drive 1 SO (TE256) GFC60A Crowfoot Wrench, 17/8 inch, 3/8 Drive 1 DM (TE265) M22520/1-01 Beta Light Switch Crimping Tool 1 SO (TE250) PFDH180 Socket, 12 Point, 9/16 inch, 3/8 Drive 1 SO 994313307 (TE253) QJFR275E Adjustable Torque Wrench, 5 to 75 ft-lb, 3/8 Drive 1 SO (TE254) QJR217C Adjustable Torque Wrench, 30 to 200 in-lb, 3/8 Drive 1 SO (TE47) YA484 Tool Box

1 SO 994313306 (TE305) PMF133 0 - 6 inch Dial Calipers 2 AP (TE258) 170-6 Apex Torqset Bit, 1/4 inch, 11/4 Length 1 AP (TE252) 668 Thickness Gauge, Straight Leaves 1 AP (TE259) 1500-P Hand Driver, Replaceable-Bit 4 MC 791800247 (TE260) 90303A247 Nylon Jack Screws 1 LE (TE263) CUTA2810114C Installation & Extraction Tool for Relief Valve 1 LE (TE264) CUTA1870104C Installation & Extraction Tool for Oil Nozzle 1 LE (TE266) CUTA1560203A Lee Plug Installation Tool 1 LE (TE267) CUTA1560103B Lee Plug Extraction Tool 1 LE (TE268) CUTA2180203A Lee Plug Installation Tool 1 LE (TE269) CUTA2180103B Lee Plug Extraction Tool 1 LE (TE270) CUTA2810203A Lee Plug Installation Tool 1 LE (TE271) CUTA2810103B Lee Plug Extraction Tool 1 LE (TE272) CUTA3120203A Lee Plug Installation Tool 1 LE (TE273) CUTA3120103B Lee Plug Extraction Tool 1 LE (TE323) CUTA1250203A Lee Plug Installation Tool 1 LE (TE324) CUTA1250103B Lee Plug Extraction Tool 1 SO (TE257) ASA204A Miniature Pick Set



Dual Acting Line Maintenance Tool KitPart Number: CST-3028-1 (TE79)

Description: Tools required for line maintenance of HD-E6C-3 propeller and PCU.

Qty. Vendor Hartzell P/N Vendor P/N Description

1 HP AST-2877-1 (TE155) n/a Torque Wrench Adapter 1 HP BST-3048 (TE320) n/a Transfer Tube and Plug Removal/Installation Tool 2 HP BST-3041 (TE84) n/a Rigging Pin 1 HP BST-10001 (TE69) n/a Transfer Tube O-ring Installation Tool 2 LS 9943EN1901 (TE262) EN1901 Propeller Sling, 1 inch x 3 feet 1 SO 9943FC012 (TE214) GFC012 Crowfoot Wrench, Open End, 3/8 inch

Dual Acting Line Maintenance Tool Kit (Hartzell Supplied Tools Only)Part Number: CST-3028-2 (TE276)

Description: Tools required for line maintenance of HD-E6C-3 propeller and PCU.

Qty. Hartzell P/N Description

1 AST-2877-1 (TE155) Torque Wrench Adapter 1 BST-3048 (TE320) Transfer Tube and Plug Removal/Installation Tool 2 BST-3041 (TE84) Rigging Pin 1 BST-10001 (TE69) Transfer Tube O-ring Installation Tool




Riser FixtureNo. CT-1075

AP

S-1

59-1

Adjustable Riser FixturePart Number: CT-1075 (TE48)

Description: Fixture to permit blade angle measurements during assembly. Used in conjunction with a bench-top protractor. For propeller models with extended hubs, adjust fixture to raise the mechanical bench top protractor TE96. A fully collapsed to fully raised fixture adds from 2.00.inches (50.8 mm) to 4.1 inches (104.1 mm) of lift.

Blade Bearing PressPart Number: DST-2934 (TE93)

Description: Press to install the inboard split bearing races and retaining rings onto single shoulder blades. The press also installs the needle roller bearings inside Y, D, and E shank blade bores.

NOTE: Does not include the hydraulic power unit.

Locator Plate ReferenceBall Size

Use with Bearing Part

NumberDST-2934+1 3/8" C-792-( )

D-7745-( )DST-2934+2 1/2" A-2202-( )

C-7438-( ) C-7075-( ) C-2882-( )

TPI-D

ST2

934



Cylinder CapPart Number: CST-3110 (TE380)

Description: Cap used with the cylinder when installing the spring assembly in compact aluminum, feathering -2 propellers.

AP

S-6

263

Blade Angle Locating FixturePart Number: CST-2969 (TE413)

Description: Fixture to check blade-to-blade angular difference before final hub assembly.

CS

T296

9A




CS

T316

9

Sleeve Installation ToolPart Number: CST-3169 (TE427)

Description: Tool for installation of the reverse adjustment sleeve in lightweight turbine propellers.

Ultrasonic Inspection Calibration StandardPart Number: CST-3012 (TE277) Supersedes BST-10009.

Description: Controlled specimen to confirm calibration of ultrasonic test equipment.

CS

T301

2



Calibration StandardPart Number: CST-3015 (TE435)

Description: Calibration standard for 101088 eddy current probe.

CS

T301

5

Bolt Alignment FixturePart Number: CST-3178 (TE448)

Description: Used to align mounting bolts in an E-7369 hub with oversize mounting bolt holes.

CS

T317

8




Propeller Assembly Table (Full Size Shown)

PROPELLER ASSEMBLY TABLE (TE129)

CST

-290

1-5

(Sho

rt T

able

w/

Bui

ldin

g B

uck

Com

pone

nts)

CST

-290

1-4

(Ful

l Tab

le w

/ B

uild

ing

Buc

k C

ompo

nent

s)

CST

-290

1-3

(Ful

l Tab

le w

/ Sp

indl

e B

ase,

Ant

i-rot

atio

n Pi

n)

CST

-290

1-2

(Sho

rt T

able

w/

Spin

dle

Bas

e, A

nti-r

otat

ion

Pin)

CST

-290

1-1

(Sho

rt T

able

)

CST

-290

1 (F

ull T

able

)

HPI Table Component Part Number and Description1 1 1 CST-2901+1 Base, Full Size

1 1 1 CST-2901-1+1 Base, Short2 2 2 2 2 2 106947 Blade Decal, HPI Oval2 2 2 2 2 2 CST-2901+3 Hanger1 1 BST-2912 (TE125) Building Buck Components

(1) (1) BST-2912-1 (TE124) Flanged Hub Spindle(1) (1) BST-2912-4 (TE4) Adapter Ring"N" Flange(1) (1) BST-2912-9 (TE2) "A" Flange Adaptor"C" Flange Adaptor(1) (1) BST-2912-10 (TE80) "C" Flange Adaptor(1) (1) 1 1 BST-2912+ (TE125-1) Spindle Base(1) (1) 1 1 BST-2912-11 (TE85) Anti Rotation Pin(1) (1) BST-2912-2 (TE122) #20 Spline Spindle(1) (1) BST-2912-3 (TE123) #30 Spine Spindle1 1 1 1 1 1 CST-2901+5 Pneumatics

Propeller Assembly TablePart Number: CST-2901-( ) (TE129)

Description: Table used to assemble/disassemble propellers. Can order a complete propeller assembly table or contact Hartzell Propeller Inc. for information to fabricate. The CST-2901 includes the propeller assembly table and the items listed in the chart below.

Anti-rotation Pin Spindle Base

NOTE: Pressure gauges included with the propeller assembly table TE129 must be re-calibrated on arrival at the final destination.

TPI-C

ST2

901



Synchrophaser Check BoxPart Number: DST-10014 (TE23)

Description: Check box to perform functional check of synchrophaser computer and related air frame components.

• BST-3050 (TE492) Chip Detector Fitting

• BST-3051 (TE493) Chip Detector Fitting Cover

NOTE: A return line fitting composed of DST-3049+69, DST-3049 +70, and DST-3049 +7 is provided inside a toolbox that is bolted to the GHPU.

Ground Hydraulic Power Unit (GHPU)Part Number: DST-3049 (TE318) AC, 110 V

DST-3049-1 (TE318) AC, 220 V

DST-3049-2 (TE318) DC, 28 V

Description: Used to change blade angle on the HD-E6C-3 propeller.

NOTE: Pressure gauges included with this ground hydraulic power unit TE318 are subject to calibration drift during shipping because of vibration, shock, etc., and must be re-calibrated by the customer on arrival at the final destination.

TPI-D

ST3

049

TPI-D

ST1

0014




Hydraulic Press Bed

Fixture No. DT-336 Jaw DT-336+6 (TE53-1) and DT336+7 (TE53-2)that grabs the pilot tube. Refer to chart.

Tool No.BST-2876 (TE107)

Hydraulic Press Ram

TPI-A

PS

0197

Pilot Tube Removal FixturePart Number: DT-336 (TE53)

Description: This part number may be used to order the drawing of the pilot tube removal fixture for local fabrication. Fixture to hold the hub during pilot tube removal. Replacement jaws are available. Used with customer procured hydraulic press.

Jaw Pilot Tube ODDT-336+6 (TE53-1) 1.5xx inch (38xx mm)DT-336+7 (TE53-2) 1.7xx inch (44xx mm)

Masking FixturePart Number: DST-3483 (TE444)

Description: Used to mask the pilot tube during the plating process.


TPI-D

ST3

483



AP

S-9

25TP

I-JM

-000

052

Blade Shank Rolling MachinePart Number: DT-1724-3( ) (TE116-3)

(Electrical Specifications: AC, 110 V, 60 Hz)Description: Complete machine to cold compression roll single shoulder aluminum

blade shanks. For operating instructions and adapter listing, refer to Hartzell Propeller Inc. Aluminum Blade Overhaul Manual 133C (61-13-33).

Superseded by: DT-1724-5 (TE116-5)

Automated Blade Shank Rolling MachinePart Number: DT-1724-5 (TE116-5)

(Electrical Specifications: AC, 100-240 V, 50/60 Hz)Description: Complete automated machine

to cold compression roll single shoulder aluminum blade shanks. For operating instructions refer to Hartzell Propeller Inc. Aluminum Blade Overhaul Manual 133C (61-13-33).

Supersedes: DT-1724-3 (TE116-3)




Bolt Alignment ToolPart Number: DST-10024(1) (TE361)

Description: Used to align A-5989-( ) mounting bolts in a D-6168 hub with oversize mounting bolt holes.

Roller Assembly ToolPart Number: DST-10016 (TE363)

Description: Used to position and align A-5654-11 rollers during assembly of A-5654-1 pitch lock unit.

DS

T100

24TP

I-DS

T-10

024-

1

DST-10024 DST-10024-1

TPI-D

ST1

0016



Go-No-Go GaugePart Number: DST-10025 (TE364)

Description: Used to inspect for deflection of drive tab on B-6428 propeller control unit drive coupling.

AP

S61

44

Pitch Change Bore PlugPart Number Description

DT-2997-4 (TE391) Used to pressure check the pitch change rod bushing on the engine-side of "N" flange hubs. Used with DT-2997-2 (TE390) or DT-2997-8 (TE394).

DT-2997-5 (TE392) Used to pressure check the pitch change rod bushing on the cylinder-side of "N" flange hubs. Used with DT-2997-7 (TE393) or DT-2997-9 (TE429).

NOTE: These part numbers may be used to order the drawings to allow for local fabrication.

AP

S6265




Pressure Check AdapterPart Number Description

DT-2997-2 (TE390) Adapter to check the pitch change rod bushing on the engine-side of "N" flange aluminum hubs. Used with DT-2997-4 (TE391).

DT-2997-7 (TE393) Adapter to check the pitch change rod bushing on the cylinder-side of aluminum hubs with fine attachment threads. Used with DT-2997-5 (TE392).

DT-2997-8 (TE394) Adapter to check the pitch change rod bushing on the engine-side of "A" flange aluminum hubs. Used with DT-2997-4 (TE391).

DT-2997-9 (TE429) Adapter to check the pitch change rod bushing on the cylinder-side of aluminum hubs with coarse cylinder attachment threads. Used with DT-2997-5 (TE392).

NOTE: These part numbers may be used to order the drawings to allow for local fabrication.

AP

S62

64



Thread Gauge Airflow KitPart Number: DST-3146 (TE382), DST-3146-1 (TE382-1)

Description: Used to inspect the condition of D-5117-1 counterweight clamp threaded holes. Also used to inspect the seal of an assembled propeller.

NOTE 1: When performing the grease seal pressure test, grease seal pressure test tool TE443 (BT-3838) must be used as an adaptor with the CST-3117 Probe Assembly. The BT-3838-1 Probe in the DST-3146-1 Kit (TE382-1) eliminates the need for an adaptor.

NOTE 2: Pressure gauges included with this thread gauge airflow kit are subject to calibration drift during shipping because of vibration, shock, etc., and must be re-calibrated by the customer on arrival at the final destination.

Components:

DST-3146 (TE382) DST-3146-1 (TE382-1)1. CST-3117 Probe Assembly 1A. BT-3838-1 Probe2. BST-3118 Flowmeter 2. BST-3118 Flowmeter3. BST-3119 Regulator 3. BST-3119 Regulator4. BST-3122 Gauge 4. BST-3122 Gauge5. CST-3135 Calibration Block

AP

S62

66

2

3

4

5

11A




Shot Peen Machine AssemblyPart Number: DST-5855(F) (TE446)(WH)

Description: A machine that reapplies the compressive layer to aluminum blade shank integral pitch change knobs. The machine consists of one (1) DST-5855-1(F) kit and the drawings needed to allow for local fabrication of the remainder of the machine.

NOTE: DST-5855 is designed for applications using 120V-60 Hz electricity. DST-5855F is designed for use with 50 Hz electric supply along with a voltage transformer.

DS

T-58

55



Shot Peen Machine Assembly, ContinuedQty. Description Hartzell P/N Vendor Vendor P/N

1 Capacitor DST-5855+1 Bodine Electric Co. 494 010541 Terminal Box DST-5855+2 Bodine Electric Co. 09841 AC Right Angle Gear Motor DST-5855+3(F) Bodine Electric Co. 0492 Modified1 Clamps DST-5855+4 DE-STA-CO TC-205U1 Motor Bracket DST-5855+5 HP n/a1 Sheave DST-5855+6 Browning OK171 Sheave DST-5855+6F Browning OK20

A/R 330 Shot DST-5855+9Ervin Industries USF Surface Prep Delong Equipment Inc Innovative Peening Syst

S-330 Cast Steel per AMS-2431/1 or 330 Shot Steel per AMS-S-13165

1 V-belt DST-5855+12F Browning 3L43A/R Almen Strip, A Scale DST-5855+13 Metal Improvement Co. 15951 Almen Gage DST-5885+14 Electronics Incorporated TSP-3B1 Cabinet DST-5885+15 HP n/a1 Nozzle Insert, Boron Carbide DST-5885+16 N.T. Ruddock Co. NT119371 Shotpeen Gun Housing DST-5885+17 N.T. Ruddock Co. NT122761 Shotpeen Nozzle Guard DST-5885+18 N.T. Ruddock Co. NT112951 Shotpeen Nozzle, O-ring DST-5885+19 N.T. Ruddock Co. 1089751 Shotpeen Retainer Ring DST-5885+20 N.T. Ruddock Co. NT120381 Shotpeen Locknut Oriface DST-5855+21 (TE603) N.T. Ruddock Co. NT119181 Shotpeen Oriface, Airjet DST-5855+22 (TE604) N.T. Ruddock Co. NT119611 Stopeen, 1/2 inch Hose Fitting DST-5855+23 N.T. Ruddock Co. NT117231 Shot Metering Valve DST-5855+24 (TE605) N.T. Ruddock Co. NT124171 Air Ball Valve DST-5855+26 (TE606) Parker Hannifin Co. XV6500P-81 Air Filter Assembly DST-5855+27 Parker Hannifin Co. 07F3HA1 Air Mounting Bracket DST-5855+28 Parker Hannifin Co. PS843P

1 Air Regulator DST-5855+29 (TE607) Parker Hannifin Co. 07R318L 07R318AC

1 Nozzle Bracket DST-5855+31 HP n/a1 Ring DST-5855+32 HP n/a1 Plate, Rotation DST-5855+33 (TE608) HP n/a1 Top Plate DST-5855+34 HP n/a1 Almen Strip Holder DST-5855+35 (TE609) HP n/a1 Guard DST-5855+42 HP n/a1 Base, Nozzle Bracket DST-5855+45 HP n/a1 Mask DST-5855+48 (TE610) HP n/a1 Motor Plate DST-5855+50 HP n/a1 Protective Guarding DST-5855+63 HP n/a1 Clamp, Door DST-5855+64 DE-STA-CO TC-205-SL1 Counter, Rotation DST-5855+66 Eaton-Cutler Hammer (Durant) 4-X-1-1-L1 Trigger DST-5855+67 HP n/a1 Plate, Wear DST-5855+68 HP n/a1 Main Power Switch DT-1724+69 Square D #2510 FG-21 Transformer Kit DT-1724+77 Magnetix Triad #AN-9MG

Stancor GSD 1500Hammond Manufacturing 175G-NA




Knob, Blade Shank - Shot Peen KitPart Number: DST-5855-1(F) (TE447)

Description: Kit consists of one (1) DST-5855+33 Rotation Plate and one (1) DST-5855+34 Top Plate plus the drawings needed to permit local fabrication of a DST-5855(F) Shot Peen Machine Assembly.

NOTE: DST-5855-1 is designed for applications using 120V-60 Hz electricity. DST-5855-1F is designed for use with 50 Hz electric supply.

Rotation Plate DST-5855+33

Top Plate DST-5855+34

TPI-J

M-0

0019

0



Optical ComparatorPart Number: Cust. P/N (TE28)

Description: Optical comparator, customer supplied, to inspect the blade retention radius to determine its acceptability for rework or return to service. Refer to Hartzell Propeller Inc. Aluminum Blade Overhaul Manual 133C (61-13-33) or Composite Propeller Blade Maintenance Manual 135F (61-13-35) for general information and optical comparator procedures.

Vendor Vendor Part Number

S-T Inductries, Inc. 14-8000-SP - (Superseded by part no. 20-3500-07) 20-3500-07 - (Supersedes part no. 14-8000-SP) 20-3500-08 - (Supersedes part no. 20-3500-07)

Micro-Vu Corp. H-14

Eastman Kodak Company 314

J & L Metrology Division PC-14

Baty International R14

Mitutoyo PH-A14

TPI-A

PS

6116




PCU Filter Removal ToolPart Number: CG40-4 (TE356) Rod

CG40-7 (TE357) Collet

Vendor: Snap-On Tools Corp. (SO)

Description: Used to remove PCU filter B-5840 from the D-1199-2 propeller control unit.

Rod CG40-4

Collet CG40-7

AP

S61

25

Ultrasonic Flaw Detector KitPart Number: 791256000 (TE285)

Description: Instrument to locate flaws in non-magnetic material (composite blade shank area).

Qty. Vendor Vendor P/N Description

1 ** See Note below. (TE375) Ultrasonic Flaw Detector 1 PM 23SC Hard-shell Shipping Case 1 PM 21PR Seiko Printer 1 PM 21PP Printer Paper 1 PM 23BAT-12 8 Hour Battery Pack 1 PM M207-RB (Included in TE374) 2.25 MHz Transducer 1 PM DLH-2 (Included in TE374) Delay Tip (Line) 1 PM BCB-58-6 Transducer Cable 1 HP CST-3012 (TE277) Ultrasonic Inspection Calibration Standard



Eddy Current Test InstrumentPart Number: ED-520 (TE133), ED-530 (TE134)

Vendor: Magnaflux Corporation (MF)

Description: Instrument to locate cracks and flaws in non-magnetic material (single shoulder aluminum blade retention radii). Used in conjunction with the following:

AST-2857 (TE94) Probe and Probe Holder for "Y" Shank Blade Inspection

AST-2979 (TE121) Test Specimen for Calibration BST-2847 (TE128) Probe Support BT-1313(-)( ) (TE95) Eddy Current Probe Unit for Blade Balance Hole

Inspection BST-3069 (TE315) Eddy Current Fixture 107514 (TE94-1) Probe for "Y" Shank Blade Inspection,

supercedes AST-2857 (TE94) 107518 (TE463) Test Specimen for Calibration

TPI-E

DD

YC

UR




AP

S-1

47

Bench Top Protractor

Riser FixtureNo. CT1075 A

PS

-159

-1

Thread Insert Installation ToolPart Number: KHT9000-9 (TE67)

Vendor: ALATEC Products Corporation (AL)

Description: Tool to assist in installing the thread insert into the pre-threaded hole and then aid in driving in the locking tangs.

Superseded by: BST-3047-( ) TE68-( )

Bench Top Blade Angle ProtractorPart Number: Vendors

PE 105 (TE96) Mausner Equipment Company, Inc. (MS) (No longer available)

799200105 (TE96) Hartzell Propeller Inc. (No longer available)

Description: Protractor to measure the blade angles of an assembled propeller while installed on the bench. Used in conjunction with the CT-1075 Riser Fixture.

NOTE: Locally procured and calibrated bubble protractor accurate to within 0.1 degree may be used and is considered equivalent.

Superseded by: BST-2960-3 TE97



AP

S-1

73A

PS

-146

CrowfootPart Number: SC038 (TE33) Crowfoot 13/16 inch SC040 (TE34) Crowfoot 11/4 inch SC042 (TE35) Crowfoot 15/16 inch SC048 (TE36) Crowfoot 11/2 inch SC052 (TE37) Crowfoot 15/8 inch SC056 (TE38) Crowfoot 13/4 inch SC060 (TE39) Crowfoot 17/8 inch

Vendor: Snap-On Tools Corporation (SO)

Description: Used in conjunction with a 1/2 inch square drive torque wrench or breaker bar for propeller assembly and disassembly.

Apex Torqset BitPart Number: 170-1/4 (TE44)

Vendor: APEX Products (AP)

Description: Bit to remove, install and torque self-locking mounting screws.




Slimsert® Installation and Removal ToolVendor: Fairchild Fasteners

Part Number Hartzell Part Number Description

SR25W4A (Rosan) MR25W4A (McKinnon) 225-072722 (Acme)

BST-2930-1 (TE389-1) (Supersedes TE389)

Used to install Slimsert®-type threaded inserts into 5/16-24 threaded holes




SR50W4A (Rosan) MR50W4A (McKinnon) 225-072738 (Acme) or 225-890051 (Acme)



SR56W4A (Rosan) MR56W4A (McKinnon) 225-072742 (Acme) or 225-890053 (Acme)

BST-2930-4 (TE389-4) Used to install Slimsert®-type threaded inserts into 11/16-12 threaded holes





BST-2930-6 (TE389-6) Used to install Slimsert®-type threaded inserts into 12-28 threaded holes







Used to install Slimsert®-type threaded inserts into 10-32 threaded holes


BST-2930-10 (TE389-10) Used to install Slimsert®-type threaded inserts into 8-32 threaded holes

BS

T-29

30



AP

S-1

78A

PS

-144

, AP

S-1

47

Helicoil Insert Removal ToolVendor: Heli-Coil Division, Emhart Fastening Systems Group (HE)

Description: Tool to remove a helicoil insert.

TE Number Vendor P/N Hartzell P/N

TE111 1227-6 791912276

Helicoil Insert Installation Tool, 7552-4Vendor: Heli-Coil Division, Emhart Fastening Systems Group (HE)

Description: Tool to pre-wind the insert to a smaller diameter for installation into the prethreaded hole.

TE Number Vendor P/N Hartzell P/N

TE66 7552-4 791975524 TE66-1 7552-5 791975525 TE66-2 7552-7 791975527




RollersPart Number: MR02030 (TE275) Roller, Steel 11/2" x 2"

MR01020 (TE328) Roller, Smooth 11/8" x 1/8"

MR10900 (TE329) Roller, Gooseneck 1" x 1/16"

MR05000 (TE330) Roller, Rubber 2"

MR05020 (TE331) Roller, Silicon 15/16" x 13/4"

Vendor: Everhard Products (EP)

Description: Miscellaneous rollers used for installation of propeller de-ice boots.

Composite Blade Repair BlanketsPart Number: HZP161001 (TE302) E10950 Blade Repair Blanket

HZP161002 (TE304) Blade Repair Blanket (4" x 12")

Vendor: BriskHeat Corporation (BR)

Description: Heat blankets which provide accelerated cure time when making repairs to composite blades. TE304 Not shown.

AP

S20

86M

R02

030



Heat GunPart Number: HL1802E (TE303)

Vendor: Steinel America (SA)

Description: Heat Gun for heat shrinking tubing around the wire harness of the de-ice boot for the HD-E6C-3( ) propeller assembly and the tubing for wires used in an electrically actuated governor.

Temp-Plate® RecorderPart Number: 240-120F (TE306) Records temperatures from 120°F to 180°F

240-190F (TE307) Records temperatures from 190°F to 220°F

Vendor: Wahl Instruments, Inc. (WI)

Description: Temperature indicating strips to be used when performing composite blade repairs with a blade repair blanket (TE302 or TE304). TE307 Not shown.

TEM

PP

LTE

.TIF

HL1

802E




Tie Strap GunPart Number: GS4H (TE332)

Vendor: All Phase Electric Supply Co. (AE)

Description: Device for securing tie straps used on de-ice boots for propeller assembly HD-E6C-3B.

Unfeathering ToolPart Number: 9943HART-001 (TE316)

Vendor: Clay-Groomer Machine Shop, Inc. (CG) or Hartzell Propeller, Inc. (HP)

Description: Tool for unfeathering propeller assemblies.

TE316A

PS

2082

GS

4H



Temp-Plate® RecorderPart Number: 240-090F (TE358)

Vendor: Wahl Instruments, Inc. (WI)

Description: Temperature indicating strips to be used when performing a de-ice system static check on the de-ice system used on the HD-E6C-3( )( ) propeller.

AP

S61

23

Signal Generator Model 3001Part Number: 90F2312 (TE359)

Vendor: BK Precision (BK)

Description: Provides an output signal to the aircraft Np sensor, allowing the de-ice system to be checked statically.

AP

S61

24




Bransonic CleanerPart Number: 000-951-005 Model B3 (TE370)

Vendor: Branson Ultrasonics Corporation (BN)

Description: Used to clean B-5840 PCU filter prior to reinstallation in D-1199-2 propeller control unit.

Megohm MeterPart Number: Customer P/N (TE354) - A megohm meter meeting the following

requirements: 0-20 megohms at 500V DC or equivalent.

Vendor: Customer Supplied (CS)

Description: Used to measure the ring-to-ring insulation resistance on the A-5635-1 slip ring. Not shown.

BRANSONIC 3

AP

S61

46



MilliohmmeterPart Number: Customer P/N (TE355) - A milliohmmeter meeting the following

specifications:

RANGE RESOLUTION MAXIMUM TEST NON DRY CIRCUIT TEST CURRENT ACCURACY 1 Year, 18°-28°C ±(%rdg+counts)

PULSED DC

200 mΩ 10 µΩ 100 mA 0.04 + 2 0.04 + 3


Description: Used to measure the bonding resistance of the HD-E6C-3( )( ) propeller. Not shown.

Pin ExtractorPart Number: MS27495R20 (TE369)


Description: Used to disassemble B-5927 electrical connector on D-1199-2 propeller control unit and used for removal of pins on electrical connector for electrically actuated governors

AP

S61

42




Slide HammerPart Number: CG250-9 and CG250-8A (TE365) Slide Hammer, 2 lb.

CG41-11 (TE366) Rod CG41-14 (TE367) Collet, 1/4 inch to 5/16 inch CG41-13 (TE368) Collet, 3/8 inch to 7/16 inch (Not shown)

Vendor: Snap-On Tools Corp. (SO)

Description: TE365 used in conjunction with TE366, and TE367 or TE368 to remove bearings B-6133-1 or B-6133-2 from D-1199-2 propeller control unit.

AP

S61

26A

PS

6127

AP

S61

28

TE365

TE366

TE367



Ultrasonic Flaw DetectorPart Number: ** See Note below. (TE375)

Description: Instrument to locate flaws in non-magnetic material (composite blade shank area). Not shown.

** NOTE: Approved detectors are listed in Hartzell Composite Blade Manual 135F (61-13-35). Contact Hartzell Product Support department for written approval of similar equipment.

Transducer AssemblyPart Number: Cust. P/N (TE374)

Vendor: Panametrics, Inc. (PM)

Description: Used in conjunction with Ultrasonic Flaw Detector (TE375) to locate flaws in non-magnetic material (composite blade shank area). Not shown.

Qty. Vendor Vendor P/N Description

1 PM M207-RB 2.25 MHz Transducer 1 PM DLH-2 Delay Line




Shot Peen GunPart Number: 02643 (TE379)

Vendor: Clemco Industries Corp. (CL)

Description: Tool used to shot peen blade balance holes. Used with BT-1271-1,2 (TE137), (not included), CT-1311 (TE12), and BT-1271(-4, -5, -6, -7,-8) (TE494-4, -5, -6, -7,-8)

Supersedes: HZP-09S#4 (GO)

BT-

1271

-1_2

Shot Peen Gun (TE379)

Shot Peen Tube Assembly (TE137) (not included)

Shot Nozzle Unit (TE494-( ) (not included)



Eddy Current ProbePart Number: 101088 (TE434) (HP)

Description: Eddy current probe for bearing cavity inspection.

Supersedes: 379-006-430 (TE434) (HK)

W10

460

No Go GaugePart Number: .2760 Pin Gauge, Minus "Y" Tolerance (TE430)

Vendor: Hemco Corporation (HM)

Description: Used to inspect the C-6066-1 preload plate.

W10

418




"E" Shank Potting MoldPart Number: 101736 (TE450)

Description: Used when filling the area of the blade retention radius of the E10950 composite blade to provide sufficient material for cutting a new radius. Used with TE449, TE451, and a customer supplied worm gear hose clamp.

"E" Shank Form ToolPart Number Description

101679 (TE449) Used to cut the retention radius of the E10950 composite blade after potting

105473 (TE449-1) Used to cut E13890 and E9193 composite blades after potting.

Description: Used with TE450 and TE451.

1016

7910

1736



Tube Puller AssemblyPart Number: 101999 (TE452) (CS)

Description: Tool used to pull the balance tube for the N-shank composite blade. This part number may be used to order the drawing of the tube puller assembly for local fabrication. Used with customer supplied press.

Composite E-shank Comparison ChartPart Number: GT-3669 (TE451)

Description: Chart to check condition and repairability of composite blade retention radius. Used in conjunction with a customer supplied optical comparator, TE449, and TE450. NOTE: This is a 14-inch diameter chart.

GT-

3669

1019

99




1019

23

Plug PullerPart Number: 101781 (TE454)

Description: Tool used to pull the blade plug for the N-shank composite blade. Used with a customer supplied press.

1017

81

Balance AdapterPart Number: 101923 (TE453)(CS)

Description: Adapter used with the balance arbor for the N-shank composite blade. Adapter Revision A used with the balance arbor for the Raptor composite blade used on reciprocating or turbine engines. This part number may be used to order the drawing of the balance adapter for local fabrication. Used with customer supplied blade balancing equipment.



MandrelPart Number: 103570 (TE456)(CS)

Description: Adapter used with the N-shank composite blade. This part number may be used to order the drawing of the mandrel for local fabrication.

1035

70

Gear Inspection WireVendor: Van Keuren (VK)

Part Number Description

0.0525 inch dia. (TE395) Used to inspect the governor control shaft.0.0620 inch dia. (TE396) Used to inspect the governor rack.0.0850 inch dia. (TE397) Used to inspect the governor drive shaft gear internal pitch

diameter.0.2634 inch dia. (TE398) Used to inspect the governor idler gear.0.2700 inch dia. (TE399) Used to inspect the governor drive shaft gear.0.0962 inch dia. (TE400) Used to inspect the governor idler gear pitch diameter.0.1400 inch dia. (TE401) Used to inspect the governor idler gear pitch diameter.0.1480 inch dia. (TE402) Used to inspect the governor drive shaft gear pitch diameter.

TPI-T

HR

EA

D-M

EA

SU

RIN

G-W

IRE

S




Torque Wrench AdapterPart Number: 101939 (TE457)(CS)

Description: Installation of the hub clamping bolts and nuts in 3-bladed compact propellers with smooth forged hubs. Used with standard 3/8 inch square drive torque wrench. This part number may be used to order the drawing of the torque wrench adapter for local fabrication.

1019

39

Shot Peen PlugPart Number: 101060 (TE458)

Description: Plug to mask the blade bore before shot peening on "P" shank, "R" shank, "W" shank, and "Z" shank blades with "N" modification.

1010

60



RingPart Number: 103572 (TE459)

Description: Adapter used with DST-2934 blade bearing press blade to locate and install the retention ring and press the bearings during epoxy bonding for the 103425 composite blade shank. This part number may be used to order the drawing of the ring for local fabrication.

1035

72

212-8 DriverPart Number: 791911212 (TE486)

Description: Bit to remove, install and torque self-locking screws.

TPI-A

PS

0146

B




Torque WrenchPart Number: 104287 (TE495)

Description: Used for blade preload of the hovercraft model 103000 assembly. Used with standard 3/8 inch square drive torque wrench This part number may be used to order the drawing of the torque wrench for local fabrication.

1042

87

Stand AdapterPart Number: 104371 (TE496)

Vendor: Mahr Federal Inc. (MH), part number 2247086

Description: Used with customer procured height stand and drive housing adapter TE497. Customer procured.

104371 (TE496)

TPI-1

0437

1



Drive Housing AdapterPart Number: 104372 (TE497)


Description: Used with customer procured height stand and stand adapter TE496. Customer procured.

104372 (TE497)

Roughness StandardPart Number: 104374 (TE498)


Description: Used to measure surface finish. Customer procured.

Part Number104374 (TE498)

TPI-1

0437

2TP

I-104

374




Crimp ToolPart Number: M22520/37-01 (TE499)


Description: Used to crimp wire splices on the electronic governor. Locally procured.

Calibration StandardPart Number: BST-3076 (TE500)

Description: Test specimen to calibrate an eddy current instrument before its use when inspecting the retention radius of X and V shank blades.

BS

T-30

76TI

-165

008



Eddy Current ProbePart Number: BST-3077-1 (TE501)

Description: Standard 0.125 inch diameter pencil probe that has a 200 KHZ frequency. Locally procured.

Fitting WrenchPart Number: 104933 (TE502)

Description: Used for fittings of anti-ice assemblies. This part number may be used to order the drawing of the wrench for local fabrication.

3077

-110

4933




Spacer BlankPart Number: 104811 (TE503)

Description: Used to make custom sized spacer in accordance with the procedure in Hartzell Propeller Inc. Blade Shank Rolling Machine Maintenance Manual 128 (61-00-28).

Plug AssemblyPart Number: 104506 (TE510)

Description: Used to perform an assembly leak check before installing the red dye oil in the propeller hub for Bantam series propellers.

Plug, 104490

O-Ring, C-3317-006

1045

06



Bearing Assembly ToolPart Number: 105189 (TE504)

Description: Used to assemble the bearing on Bantam blades. This part number may be used to order the drawing of the bearing assembly tool for local fabrication.

ClampPart Number: 105190 (TE505)

Description: Used to assemble the bearing on Bantam blades. This part number may be used to order the drawing of the clamp for local fabrication.

1051

8910

5190




Leak Check ManifoldPart Number: 104507 (TE506)

Description: Used to perform an assembly leak check before installing the red dye oil in the propeller hub.

NOTE: Pressure gauges included with this leak check manifold are subject to calibration drift during shipping because of vibration, shock, etc., and must be re-calibrated by the customer on arrival at the final destination.

AdapterPart Number: 104504 (TE507)

Description: Used to perform an assembly leak check before installing the red dye oil in the propeller hub. Used with 104507 (TE506).

Valve Assembly,B-1938

Air Pressure Gage,

102560-1

Reducer, 104509

Tee, 104508

1045

0710

4504



Check CylinderPart Number: 104798 (TE508)

Description: Used to perform an assembly leak check before installing the red dye oil in the propeller hub for Bantam 5-bladed series propellers. Used with 104507 (TE506) and 104504 (TE507).

1047

98A

1051

67

Check CylinderPart Number: 105167 (TE509)

Description: Used to perform an assembly leak check before installing the red dye oil in the propeller hub for 6-bladed Hovercraft propellers. Used with 104507 (TE506) and 104504 (TE507).




Double Shoulder Blade Eddy Current KitPart Number: BST-3075 (TE516)

Description: Instruments used to perform eddy current inspection of the double shoulder blade retention radius.

Qty. Vendor P/N Description

1 BST-3069 (TE315) Probe Holder 1 BST-3076 (TE500) Calibration Standard 1 BST-3077-1 (TE501) Eddy Current Probe 1 BST-3078 Teflon Tape 1 BST-3075+1 Protective Case

Calibration StandardBST-3076 (TE500)

Probe HolderBST-3069 (TE315)

Eddy Current ProbeBST-3077-1 (TE501)

3075



Torque Unit AdapterPart Number: 105266 (TE517)

Description: Wrench to tighten and torque mounting bolts on 3-bladed reversing Bantam propellers. Used in conjunction with a standard 1/2 inch drive torque wrench.

NOTE: This part number may be used to order the drawing of the torque wrench adapter to permit local fabrication.

Torque Unit AdapterPart Number: 105269 (TE518)

Description: Wrench to tighten and torque mounting bolts on 3-bladed reversing Bantam propellers. Used in conjunction with a standard 1/2 inch drive torque wrench.

NOTE: This part number may be used to order the drawing of the torque wrench adapter to permit local fabrication.

1052

6610

5269




Hovercraft 5-Way AdapterPart Number: BST-2912-20 (TE519)

Description: Adapter permits mounting of 5-bladed Hovercraft propellers to the CST-2901( ) Propeller Assembly Table. Must be used with the BST-2912-1 Flanged Spindle.

Hovercraft 6-Way AdapterPart Number: BST-2912-21 (TE520)

Description: Adapter permits mounting of 6-bladed Hovercraft propellers to the CST-2901( ) Propeller Assembly Table. Must be used with the BST-2912-1 Flanged Spindle.

BS

T-29

12-2

0B

ST-

2912

-21



Balance AdapterPart Number: 105274 (TE531)

Description: Adapter used with the balance arbor for the Bantam composite blade. This part number may be used to order the drawing of the balance adapter for local fabrication. Used with the customer supplied blade balancing equipment.

Bantam Blade Spud AdapterPart Number: ** See Note below. (TE532)

Description: Adapter used with the blade spud for the Bantam composite blade. Not shown.

** NOTE: Contact Hartzell Propeller Inc. Product Support department for recommended tooling.

1052

74.a

i




Leak Detector KitPart Number: 102560 (TE533)

Description: Leak detector kit is an assembly of a digital pressure gauge, fill valve, fittings, tubing, and a hub connector. The kit is used to inspect the propeller seals with compressed air prior to filling the hub with red dyed oil in accordance with HC-SL-61-273.

NOTE: Pressure gauges included with this leak detector kit are subject to calibration drift during shipping because of vibration, shock, etc., and must be re-calibrated by the customer on arrival at the final destination.

1025

6010

5478

97

.65

PS

I

Air Pressure Gauge102560-1

Valve AssemblyB-1938

Barbed Fitting102560-2

Tubing102560-3

Tee Fitting102560-4

Blade Seal ProbeBT-3838-1

O-RingC-3317-010-2

Blade Inspection AdapterPart Number: 105478 (TE534)

Description: Adapter used with the NC8834( ) composite blade.

AlteredBushing Liner105478-2

Spacer105478-4

Hold Down105478-3

Screw

Set Screw

Altered Bushing Liner105478-5r

Frame Unit105478-1

Knob105478-6



Drill JigPart Number: 104052 (TE535)

Description: Drill jig used to repair the dowel pin in the existing N7605(B,K)( ) and N7893( ) composite blades in accordance with HC-SB-61-319.

1040

52

104052-2Knob Locator

104052-1Base

BS

T-29

12-1

9A

Hub Flange SpindlePart Number: BST-2912-19 (TE536)

Description: Adapter permits mounting of the H, T, Q, and G Hub Flange propellers to the CST-2901( ) Propeller Assembly Table. Used with TE548 Bantam Spring Compressor.

Anti-rotate Pin (included)




Shank Spacer PullerPart Number: 102516 (TE538)

Description: Tool for engaging the threaded bearing spacer in P, R, P/N, M, T, Z/W, W, M/N, and T/N blades to pull out the spacer and the outboard bearing.

Shank Spacer PullerPart Number: 102515 (TE537)

Description: Tool for engaging the threaded bearing spacer in V, V/N, and MV blades to pull out the spacer and the outboard bearing.

1025

1510

2516



1034

54

Preload Stud PlPart Number: 103454 (TE540)

Description: Used for the 103437 hub at overhaul to re-install the mounting studs properly. Drawing available for local fabrication, not for sale.

Tube NutPart Number: 106450 (TE570) For building the "G" flange propeller

Description: Used to hold the propeller to the assembly table spindle and to protect the threads of the captive fasteners within the spindle slots. Used with TE536 BST-2912-19 Hub Flange Spindle.

TPI-1

65A

-106

450




Valve Assembly Check ToolPart Number: 105615 (TE547)

Description: Tool to pressure test the internal relief valve contained in the relief valve bolt unit in accordance with HC-SB-61-350. This part number may be used to order the drawing of the valve assembly check tool for local fabrication.

TPI-M

B-0

022

Cap

Rubber WasherO-ring

Relief Valve Bolt Unit

Housing

Inlet Port for Regulated, Filtered Air

Hole



Bantam Spring CompressorPart Number: 105532 (TE548)

Description: Adapter permits mounting of Bantam propellers to the CST-2901( ) Propeller Assembly Table. Used with TE536 BST-2912-19 Hub Flange Spindle.

NOTE: This part number may be used to order the drawing of the Bantam Spring Compressor to permit local fabrication.

Components: 1 105663 (TE548-1) Extension

2 105664 (TE548-2) Pull Rod

3 105665 (TE548-3) Compression Spring

TPI-1

6501

0

1

2

3




Right Angle Grease CouplerPart Number: 105702 (TE559)

Description: Fits used between the counterweight and the lubrication fitting of the TBM Socata 5-way Propeller, HC-E5N-3C. Provides 90 degree access.

Vendor Vendor Part Number MC 1091K61

OT 2322

TM THX-418MD0213-4

AF 8034

SP QCC-HTR

MA GGA21600

SM 06135

LI 5883

"F" Flange Bantam Adapter RingPart Number: BST-2912-22 (TE550)

Description: Adapter permits mating to the BST-2912-19 spindle so that the Bantam spring compressor features will work. Used with TE536 BST-2912-19 Hub Flange Spindle.

NOTE: This part number may be used to order the drawing of the "F" Flange Bantam Adapter Ring to permit local fabrication.

TPI-B

ST-

2912

-22



Air Check BlockPart Number: 105236 (TE568)

Description: Used to provide a method to check the leak check manifold 104507 (TE506) assembly and to provide a protective way to store the leak check manifold 104507 (TE506) when not in use.

TPI-1

65-1

0523

6

Extended SocketPart Number: 106221 (TE567) For five-bladed light-weight turbine propellers

Description: Modified extended socket used to torque the piston mounting nut against the piston on lightweight turbine propellers.

TPI-1

65A

-106

221

Extended Socket 106221TE567

Pitch ChangeRod

Piston

Cylinder




Blade Spud AdapterPart Number: 101932 (TE455) (CS)

Description: This part number may be used to order the drawing of the blade spud adapter for local fabrication. Adapter used with a locally procured blade spud inspection bench. Only use adapter 101932 (TE455) on composite blades that have an integral pitch change knob.

Superseded by: 105501 (TE539)

1019

32

Blade Inspection AdapterPart Number: 105501 (TE539)

Description: This part number may be used to order the drawing of the adapter for local fabrication. Adapter used with a locally procured blade spud inspection bench. Use adapter 105501 (TE539) for any composite blade that needs an adapter except for E, M, and B shank composite blades.

Supersedes: 101932 (TE455)

1055

01_



C-shank Rolling Conversion KitPart Number: 106542 (TE594)

Description: The C-shank Rolling Conversion Kit is an assembly to convert the Hartzell Propeller Inc. Rolling Machine to roll the Raptor C-shank blades.

Part Number Description Quantity 104811 (TE503) Blank, Spacer 1

BST-2869-1 (TE635) Spacer 1

DT-1724+171 (TE598) Base 1

DT-1724+172 (TE599) Ring, Clamp 1

DT-1724+173 (TE600) Pin, Locator 1

TPI-J

M-0

0001

1

Spacer Blank 104811 (TE503)

BaseDT-1724+171 (TE598)

Clamp RingDT-1724+172 (TE599)

Locator PinDT-1724+173 (TE600)

SpacerBST-2869-1 (TE635)




Shot Peen Masking ToolsPart Number: Mask DST-5855+72 (TE601)

Mask DST-5855+73 (TE602)

Description: Masking tools for the Raptor C-shank.

TPI-1

65A

-DS

T-58

55+7

2, T

PI-1

65A

-DS

T-58

55+7

3

Mask DST-5855+72 (TE601) Mask

DST-5855+73 (TE602)

TPI-1

65A

-106

513

Piston Ring Clamp KitPart Number: 106513 (TE616) For removing the piston ring from piston units C-497 and

C-497-1.

Description: The piston ring clamp kit includes tools and parts to remove the piston ring from piston units C-497 and C-497-1. The kit contains the following:

Hartzell P/N Description Qty

106294 (TE617) Clamp, Ring, Piston 1

106295 (TE618) Base, Clamp 1

106296 (TE619) Washer, Clamp 1

106294(TE617)

106295(TE618)

106296(TE619)



TPI-1

65A

-106

964

Assembly Low Pitch SpacerPart Number: 106964 (TE634)

Description: Used to set low pitch for assembling the HC-A2(V,MV)20-5L.

MaskPart Number: 107139 (TE636)

Description: Used as a paint mask for the E-7486 clamp.

TPI-J

M-0

0002

2




Hardware KitPart Number: CST-3200 (TE637)

Description: Tools used with the TE638 Force Gauge for the applied load calibration of the DT-1724-5 Automated Rolling Machine. Tools TE637 and TE638 are sold separately. One hardware kit can be used for multiple rolling machines.

Force Gauge (TE638) (For reference only - not included with TE637)

TPI-J

M-0

0007

8

Force GaugePart Number: 107192 (TE638)

Description: Measures an applied force from the roller on the DT-1724-5 Automated Rolling Machine. The force gauge is used with CST-3200 (TE637). One force gauge can be used for multiple rolling machines.

TPI-J

M-0

0007

9



Position GaugePart Number: 107190 (TE639)

Description: A tool to establish a home position on the DT-1724-5 Automated Rolling Machine. One position gauge can be used for multiple rolling machines.

TPI-J

M-0

0008

0

Torque Wrench AdapterPart Number: DT-1724+193 (TE640)

Description: A wrench adapter used to torque the DT-1724-5 Automated Rolling Machine chuck.

TPI-J

M-0

0008

2




Sealant Gun AssemblyPart Number: See NOTE below (TE641)

Description: The Sealant Gun Assembly uses facility supplied air pressure to dispense sealant. Components of the Sealant Gun Assembly are listed below:

NOTE: Components must be purchased separately from the vendor.

Vendor Vendor P/N DescriptionPG 250255 Sealant Gun with

2.5 oz Retainer

PG 280014 Hose Assembly, 15 ft in length

PG 220538 Nozzle

PG 220928 6.0 oz Retainer (optional)

TPI-J

M-0

0008

5

Nozzle (P/N: 220538)Hose Assembly (P/N: 280014)

Sealant Gun - includes 2.5 oz. Retainer (P/N: 250255)

6.0 oz. Retainer (P/N: 220928)



illustrated tool and equipment - hartzellprop.com · illustrated tool and equipment manual hartzell...

Documents