hyundai accent 2007

5/24/2018 Hyundai accent 2007

1/283

2007


2/283

A020A01A-AAT

RESPONSIBILITY FOR MAINTENANCE

The maintenance requirements for your new Hyundai are found in Section 5. As the owner, it is yourresponsibility to see that all maintenance operations specified by the manufacturer are carried out

at the appropriate intervals. When the vehicle is used in severe driving conditions, more frequentmaintenance is required for some operations. Maintenance requirements for severe operatingconditions are also included in Section 5.

A010A03A-AAT

WARRANTIES FOR YOUR HYUNDAI VEHICLE

Please consult your Owner's Handbook & Warranty Information booklet for your vehicle'sspecific warranty coverage.


3/283

All information in the Owner's Manual is current at the time of puHowever, Hyundai reserves the right to make changes at any time as ppolicy of continual product improvement may be carried out.

This manual applies to all Hyundai models and includes descriptions anations of optional as well as standard equipment. As a result, youmaterial in this manual that does not apply to your specific vehicle.

OWNER'S MANUA

A030A01A-AAT

OperationMaintenance

Specifications


4/283

A080A01S-AAT

TWO-WAY RADIO OR CELLULAR TELEPHONE INSTALLATION

Your vehicle is equipped with electronic fuel injection and other electronic components. It is possiblefor an improperly installed/adjusted two-way radio or cellular telephone to adversely affect electronic

systems. For this reason, we recommend that you carefully follow the radio manufacturer's instruc-tions or consult your Hyundai dealer for precautionary measures or special instructions if you chooseto install one of these devices.

!A070A01A-AAT

CAUTION: MODIFICATIONS TO YOUR HYUNDAI

Your Hyundai should not be modified in any way. Such modifications may adversely affect theperformance, safety or durability of your Hyundai and may, in addition, violate conditions of the limitedwarranties covering the vehicle. Certain modifications may also be in violation of regulationsestablished by the U.S. Department of Transportation and other federal or state agencies.


5/283

!

A090A01A-AAT

SAFETY AND VEHICLE DAMAGE WARNING

This manual includes information titled as WARNING, CAUTION and NOTE.These titles indicate the following:

WARNING:This indicates that a condition may result in harm, serious injury or death to you or other personsif the warning is not heeded. Follow the advice provided with the warning.

CAUTION:This indicates that a condition may result in damage to your vehicle or its equipment if the cautionis not heeded. Follow the advice provided with the caution.

NOTE:This indicates that interesting or helpful information is being provided.

!


6/283

A110A01A-AAT

VEHICLE DATA COLLECTION AND EVENT DATA RECORDERS

Your Hyundai vehicle is equipped with many high technology, electronically controlled systems

that help to ensure your vehicle operates properly and provides the performance that youexpect. These systems utilize computers to monitor the operation of various systems andcomponents and help to control their operation. These computerized system operations arewide-ranging and involve components to reduce emissions, to continuously evaluate thereadiness of the airbag and seat belt pretensioner systems, to determine when the airbag andseat belt pre-tensioner systems should be deployed and then to activate the deployment, andif equipped, to operate anti-lock braking, traction control and electrical stability control to assist

the driver to control the vehicle in difficult driving situations. These systems electronically storeinformation that is useful to service technicians when they need to diagnose and repair thesesystems. Additional information is stored only when a crash occurs that results in thedeployment of the airbags or seat belt pre-tensioners. This type of data storage is done bydevices called event data recorders(EDR).

After a crash event, the airbag and seat belt pre-tensioner computer system, known as theSupplemental Restraint System Control Module (SRSCM) or Airbag Control Unit (ACU), mayrecord some information about the condition of the vehicle and how it was being operated. Thisinformation consists of data related to seat belt usage and if there was diagnostic informationin the airbag or seat belt systems at the time that a crash occurred, and if the ACU sensed thata crash of sufficient severity occurred to require seat belt pre-tensioner or airbag deployment.

To retrieve this information, special equipment is needed and access to the vehicle or the devicethat stores the data is required. Hyundai will not access information about a crash event or shareit with others except:

o in response to an official request of police or similar government office, oro with the consent of the vehicle owner or, if the vehicle is leased, with the consent of the lessee,

or

o as part of Hyundais defense of litigation, oro as required by law.


7/283

A040A01A-AAT

FOREWORD

Thank you for choosing Hyundai. We are pleased to welcome you to the growing number of discriminatingpeople who drive a Hyundai. The advanced engineering and high-quality construction of each Hyundai webuild is something of which we're very proud.

Your Owner's Manual will introduce you to the features and operation of your new Hyundai. It is suggestedthat you read it carefully because the information it contains can contribute greatly to the satisfaction you

receive from your new car.

The manufacturer also recommends that all service and maintenance on your car be performed by anauthorized Hyundai dealer. Hyundai dealers are prepared to provide high-quality service, maintenance andany other assistance that may be required.

A050A04A-AAT

HYUNDAI MOTOR COMPANY

Note: Because future owners will also need the information included in this manual, if you sell this Hyundai,please leave the manual in the vehicle for their use. Thank you.

CAUTION:Severe engine and transaxle damage may result from the use of poor quality fuels and lubricants thatdo not meet Hyundai specifications. You must always use high quality fuels and lubricants that meetthe specifications listed on Page 9-4 in the Vehicle Specifications section of the Owner's Manual andwhich also appear in the Service Station Information on the back cover of the Owner's Manual.

Copyright 2006 Hyundai Motor Company. All rights reserved. No part of this publication may be reproduced,stored in any retrieval system or transmitted in any form or by any means without the prior written permissionof Hyundai Motor Company.

!


8/283

A100A03A-AAT

Guide to Hyundai Genuine Parts1. What are Hyundai Genuine Parts?

Hyundai Genuine Parts are the sameparts used by Hyundai Motor Companyto manufacture vehicles. They are de-signed and tested for the optimum safety,performance, and reliability to our cus-tomers.

2. Why should you use genuine parts?

Hyundai Genuine Parts are engineeredand built to meet rigid manufacturingrequirements. Using imitation, counter-feit or used salvage parts is not covered

under the Hyundai New Vehicle Lim-ited Warranty or any other Hyundaiwarranty. In addition, any damage to or

failure of Genuine Hyundai Parts causedby the installation or failure of an imita-

tion, counterfeit or used salvage part isnot covered by any Hyundai Warranty.

3. How can you tell if you are purchasingHyundai Genuine Parts?

Look for the Hyundai Genuine Parts

Logo on the package (see below).

Hyundai Genuine Parts exported to theUnited States are packaged with labelswritten only in English.

Hyundai Genuine Parts are only soldthrough authorized HyundaiDealerships.

" To find the closest authoriz

call 1-800-826-CARS "

A100A01L A100A02L


9/283

TABLE OF CONTENTS

SECTION

FEATURES OF YOUR HYUNDAI

DRIVING YOUR HYUNDAI

WHAT TO DO IN AN EMERGENCY

CORROSION PREVENTION & APPEARANCE CARE

VEHICLE MAINTENANCE REQUIREMENTS

DO-IT-YOURSELF MAINTENANCE

EMISSION CONTROL SYSTEMS

CONSUMER INFORMATION, REPORTING SAFETY DEFECTS &BINDING ARBITRATION OF WARRANTY CLAIMS

VEHICLE SPECIFICATIONS

INDEX


10/283

B250A01MC-AAT

INSTRUMENTS AND CONTROLS


11/283

1. Hood Release Lever ................................................... 1-902. Front Fog Light Switch (If Installed) ............................ 1-763. Panel Brightness Control Knob (Rheostat Switch) .... 1-754. Instrument Cluster ....................................................... 1-695. Multi-Function Light Switch......................................... 1-726. Horn and Driver's Front Airbag .......................... 1-98, 1-427. Windshield Wiper/Washer Switch .............................. 1-738. Hazard Warning Light Switch ..................................... 1-75

9. Digital Clock ................................................................ 1-7710. "PASSENGER AIR BAG OFF" Indicator ..................... 1-4911. Rear Window Defroster Switch ................................... 1-7612. Audio System (If Installed) ........................................ 1-119

13. Passenger's Front Airbag .....................................14. Glove Box ..............................................................15. Heating/Air Conditioning Control Panel (If Installe16. Multi Box ...............................................................17. Cigarette Lighter ...................................................18. Power Outlet .........................................................19. Ashtray ..................................................................20. Shift Lever .............................................................

21. Parking Brake Lever .............................................22. Front Drink Holder ................................................23. Trunk Lid Release Lever ......................................24. Fuel Filler Lid Release Lever ...............................

CAUTION:When installing a container of liquid air freshener inside the vehicle, do not place it near the instrument clusternor on the instrument panel surface. If there is any leakage from the air freshener onto these areas(Instrument cluster, instrument panel or air ventilator), it may damage these parts. If the liquid from the airfreshener does leak onto these areas, wash them with water immediately.

!


12/283

YOUR VEHICLE AT A GLANCE

High Beam Indicator Light

Parking Brake/Low Brake Fluid Level

Warning Light

Door Ajar Warning Light and Chime

O/D OFF Indicator

(Automatic transaxle only)

B255A01MC-AAT

INDICATOR SYMBOLS ON THE INSTRUMENT PANEL

* More detailed explanations of these items will be found begining on page 1-64.

SRS (Airbag) Warning Light

ABS Service Reminder Indicator (If Installed)

Turn Signal Indicator Lights

Low Oil Pressure Warning Light

Charging System Warning Light

Low Fuel Level Warning Light

Malfunction Indicator Light

Seat Belt Warning Light and Chime

Trunk Lid / Tail Gate Open Warning Light

Check Fuel Filler Cap Warning Light

Engine Coolant Temperature Indicator Lig

(If Installed)


13/283

FEATURES OF YOUR HYUNDAI

Fuel Recommendations ................................................ 1-2Breaking in Your New Hyundai .................................... 1-3Keys .............................................................................. 1-4Door Locks ................................................................... 1-4

Theft-Alarm System...................................................... 1-8Window Glass ............................................................ 1-11Seats ........................................................................... 1-13Seat Belts ................................................................... 1-22Child Restraint System............................................... 1-31Advanced Supplemental Restraint (AIRBAG) System ...................................................................... 1-41Instrument Cluster and Indicator Lights ..................... 1-60Warning and Indicator Lights ...................................... 1-64Trip Computer ............................................................. 1-72Multi-Function Light Switch ......................................... 1-75

Windshield Wiper and Washer Switch ....................... 1-77Sunroof ....................................................................... 1-83Mirror........................................................................... 1-88Hood Release ............................................................. 1-93Heating and Cooling Control .................................... 1-102Stereo Sound System .............................................. 1-121Audio System ........................................................... 1-123Antenna ..................................................................... 1-150


14/283

1FEATURES OF YOUR HYUNDAI

2 FUEL RECOMMENDATIONS

UNLEADEDFUEL ONLY

B010A01MC-A

!

B010A02MC-AAT

Use Unleaded Gasoline

Unleaded gasoline with a Pump OctaneRating of 87 (Research Octane Number91) or higher must be used in yourHyundai.

B010B01A-AAT

What About Gasohol?Gasohol (a mixture of 90% unleadedgasoline and 10% ethanol or grain alco-hol) may be used in your Hyundai. How-ever, if your engine develops driveabilityproblems, the use of 100% unleaded

gasoline is recommended. Fuels withunspecified quantities of alcohol, oralcohols other than ethanol, should notbe used.

B010C01A-AAT

Use of MTBE

Hyundai recommends that fuels contain-ing MTBE (Methyl Tertiary Butyl Ether)over 15.0% vol. (Oxygen Content 2.7%weight) should not be used in yourHyundai.

Fuel containing MTBE over 15.0% vol.(Oxygen Content 2.7% weight) may re-duce vehicle performance and producevapor lock or hard starting.

B010D01A-AAT

Do Not Use MethanolFuels containing methanol (whol) should not be used in youThis type of fuel can reduce veformance and damage compthe fuel system.

CAUTION:Your Hyundai's New Vehicle Limranty may not cover damage

system and any performance that are caused by the use of taining methanol or fuels cMTBE (Methyl Tertiary Butyl E15.0% vol. (Oxygen Content 2.7

!

CAUTION:o Do not "top off" after the nozzle au-

tomatically shuts off when refueling.o Tighten the cap until it clicks, other-

wise the " " light will illuminate.o Always check that the fuel cap is

installed securely to prevent fuelspillage in the event of an accident.

FEATURES OF YO


15/283

FEATURES OF FEATURES OF YO

BREAKING IN YOUR NEWHYUNDAI

B010F01A-AAT

Operation in Foreign Countries

If you are going to drive your Hyundai inanother country, be sure to:

o Observe all regulations regarding reg-istration and insurance.

o Determine that acceptable fuel is avail-able.

B010E01A-AAT

Gasolines for Cleaner AirTo help contribute to cleaner air, Hyundairecommends that you use gasolinestreated with detergent additives, whichhelp prevent deposit formation in theengine. These gasolines will help the

engine run cleaner and enhance perfor-mance of the Emission Control System.

B020A01S-AAT

During the First 1200 Miles (2000Km)

No formal "break-in" procedure is requiredwith your new Hyundai. However, youcan contribute to the economical opera-tion and durability of your Hyundai by

observing the following recommenda-tions during the first 1200 miles (2000km).

o Don't drive faster than 55 MPH (88 km/h).

o While driving, keep your engine speed

(rpm, or revolutions per minute) be-tween 2,000 rpm and 4,000 rpm.

o Use moderate acceleration. Don't startquickly or depress the acceleratorpedal fully.

o For the first 200 miles (300 km), try to

avoid hard stops.o Don't lug the engine (in other words,don't drive so slowly in too high a gearthat the engine "bucks"-shift to a lowergear).

o Whether going fast or slow,

speed from time to time.o Don't let the engine idle lon

minutes at one time.o Don't tow a trailer during the

miles (2,000 km) of operati

1FEATURESOFYOURHYUNDAI


16/283


4 DOOR LOCKS

!

B030B01NF-GAT

Record Your Key Number

A code number is recorded on the num-ber tag that came with the keys to yourHyundai. This key number tag should notbe left with the keys but kept in a safeplace, not in the vehicle. The key numbershould also be recorded in a place where

it can be found in an emergency.If you need additional keys, or if youshould lose your keys, your authorizedHyundai dealer can make new keys if youcan supply the key number.

B030B01MC

B040A01A-AAT

WARNING:o Unlocked doors can be da

Before you drive away (esthere are children in the cathat all the doors are secure

and locked so that the doobe opened from the inside. Tensure that the doors wopened accidentally. Also, wbined with the proper usbelts, locking the doors hoccupants from being ejethe car in case of an accid

o Before opening the door, alfor and avoid oncoming tr

KEYS

B030A01A-AAT

For greater convenience, the same keyoperates all the locks in your Hyundai.However, because the doors can belocked without a key, carrying a spare keyis recommended in case you accidentallylock one key inside the car.

OMC025001

FEATURESOFFEATURES OF YO


17/283


B040B02A-AAT

Locking and Unlocking Front Doorswith a Key

o The door can be locked or unlockedwith a key.

o Lock the door by turning the key to-ward the front of the vehicle and un-lock it by turning the key toward the

rear.

NOTE:The driver's door can be unlocked byturning the key once toward the rear. Ifyou wish to unlock all doors, turn the keyagain toward the rear within 4 seconds(With the central door locking system).

OMC025005

UNLOCK

LOCK

The doors can be locked without a key.To lock the doors, first push the insidelock switch to the "LOCK" position so thatthe red mark on the switch is not visible,then close the door.

NOTE:o When pushing the lock switch of thepassenger's door to the "LOCK" po-sition, all doors can be locked.

o If your vehicle is equipped with thecentral door locking system, the doorwill not lock if the key is left in the

ignition switch when the front doorsare closed.

B040C01MC-AAT

Locking from Outside

B040C04MC

o When locking the door from

be careful not to lock the the ignition key left in the

o To protect against theft, amove the ignition key, closdows, and lock all doorstrunk lid (4 Door) / tail gatewhen leaving your vehitended.



18/283


6

!

B040D01MC-AAT

Locking from the Inside

To lock the doors from the inside, simplyclose the door and push the lock switchto the "LOCK" position.

NOTE:o When pushing the lock switch of the

passenger's door to the "LOCK" po-sition, all doors can be locked.

o When the door is locked, the redmark on the switch is not visible.

o The driver's door can be opened bypulling the inside door handle even if

the inside lock switch is pushed tothe "LOCK" position.

B040E04A-AAT

CHILD-PROTECTOR REAR DOOR

LOCK (4 Door)

Your Hyundai is equipped with left andright side "child-protector" rear door locks.

OMC025006

UNLOCK

LOCK

B040E01MC

WARNING:Be careful not to pull the inside doorhandle while driving. If you pull the insidedoor handle, the door can be opened andyou may be ejected from the vehicle andcan be injured or killed.

When the lock mechanism is

the rear door cannot be openeinside. Its use is recommendever there are small children iseat.

To engage the child-protector that the door cannot be opene

inside, move the child-protectothe " " position and close the dthe lever to the " " position mal door operation is desired

To open the door from the outhe outside door handle.

FEATURESOFFEATURES OF YO


19/283


!

B040G01MC-AAT

Central Door Locks (If Installed)

The central door locking switch is lo-cated on the driver's armrest. It is oper-ated by depressing the door lock switch.If any door is open when the switch isdepressed to the "LOCK" position, thedoor will remain locked when closed.

NOTE:o When depressing the front portion

of the door lock switch, all vehicledoors will lock.

o When depressing the rear portion ofthe switch, all vehicle doors will un-lock.

B040G02MC

o The driver's door can be opened by

pulling the inside door handle even ifthe front portion of the central doorlocking switch has been depressedto lock the doors.

o If the door is locked/unlocked mul-tiple times in rapid succession witheither the vehicle key or door lock

switch, the system may stop operat-ing temporarily in order to protectthe circuit and prevent damage tosystem components.

o The central door locking is operatedby turning the key in the driver's

door lock toward the front or rear ofthe vehicle.

WARNING:Be careful not to pull the inside doorhandle while driving. If you pull the in-side door handle, the door can be openedand you may be ejected from the ve-hicle and can be injured or killed.

!

B070F03O-AAT

KEYLESS ENTRY SYSTEM(If Installed)

NOTE:This device complies with ParFCC rules. Operation is subjfollowing two conditions:

(1) This device may not causinterference. and (2) this devaccept any interference receIncluding interference that mundesired operation.

CAUTION:Changes or modifications not approved by the party respocompliance could void the uthority to operate the equipem

UNLOCKLOCK



20/283


8 THEFT-ALARM SYSTE

B070A01A-AAT

(If Installed)This system is designed to prtection from unauthorized entcar. This system is operatedstages: the first is the "Armed" second is the "Alarm" stage, an

is the "Disarmed" stage. If trigsystem provides an audible ablinking of the turn signal ligh

Locking doors

1. Close all doors.2. Push the "LOCK" button on the trans-

mitter.3. At the same time all doors lock, the turn

signal light will blink once to indicatethat the system is armed.

Unlocking doors

1. Push the "UNLOCK" button on thetransmitter.

2. At the same time the driver's doorunlocks, the turn signal light will blink

twice to indicate that the system isdisarmed.

NOTE:If you wish to unlock all the doors, pressthe "UNLOCK" button on the transmitteragain within 4 seconds.

NOTE:

The transmitter will not work if any offollowing occur:- The ignition key is in ignition switch.- You exceed the operating distance

limit (10 m).- The battery in the transmitter is weak.- Other vehicles or objects may be

blocking the signal.- The weather is extremely cold.- The transmitter is close to a radio

transmitter such as a radio stationor an airport which can interfere withnormal operation of the transmitter.

When the transmitter does not workcorrectly, open and close the door withthe ignition key. If you have a problemwith the transmitter, contact an autho-rized Hyundai Dealer.

NOTE:

Keep the transmitter away from water orany liquid. If the keyless entry system isinoperative due to exposure to water orliquids, it will not be covered by yourmanufacturer vehicle warranty.



21/283

!B070B01MC-A

B070B01MC-AAT

Armed Stage

Park the car and stop the engine. Arm thesystem as described in the following para-graph.

1) Remove the ignition key from the igni-tion switch.

2) Make sure that the engine hood andtrunk lid (4 Door)/tail gate (3 Door) areclosed and latched.

3) Lock the doors using the transmitter ofthe keyless entry system.

After completion of the steps above, theturn signal lights will blink once to indi-cate that the system is armed.

The system can be armed by locking the

doors with the key from the front doors ortail gate (3 Door). However, the hazardwarning lights are not operated.

NOTE:If any door, trunk lid (4 Door)/tail gate (3Door) or engine hood remains open, the

system will not be armed. If this hap-pens, rearm the system as describedabove.

CAUTION:o Do not arm the system until all pas-

sengers have left the car. If the sys-tem is armed while a passenger(s)remains in the car, the alarm may beactivated when the remainingpassenger(s) leaves the car.

o If the "LOCK" button is pressed oncemore within 4 seconds after pushingthe "LOCK" button on the transmit-ter, the alarming horn will sound onceto indicate that the system is armed.

LOCK

B070C01MC-AAT

Alarm StageThe alarm will be activated if following occurs while the carand the system is armed.

1) Any door, tail gate (3 Door)

is opened without using the tor the ignition key.2) The trunk lid(4 Door) is ope

out using the ignition key.3) The engine hood is opened

The alarming horn will sound an

signal lights will blink continuoseconds (This happens 3 timeoff the system, unlock the dootransmitter or the ignition key.

CAUTION:Avoid trying to start the enginesystem is armed.

!



22/283

110

B070E01MC-AAT

Replacing the batteryWhen the transmitter's batteryget weak, it may take several the button to lock or unlock the dthe LED will not light. Replace tas soon as possible.

Battery type : CR2032

B070E01MC-AAT

Panic Warning

1. Push the "PANIC" button on the trans-mitter.

2. At the same time, the alarming hornwill sound and the turn signal lightswill blink continuously for 30 seconds.

3. To turn off the system, push any buttonon the transmitter or lock/unlock thedoors by turning the key.

B070E01MC-A

B070D01MC-AAT

Disarmed Stage

The system will be disarmed when thefollowing step is taken:

The doors are unlocked by depressingthe "UNLOCK" button on the transmitteror unlocked with the ignition key.

After depressing unlock button, the haz-ard warning lights will blink twice to indi-cate that the system is disarmed.

If any door, trunk lid(4 Door)/tail gate(3Door) or engine hood is not opened within30 seconds, the system will be rearmed.

B070D01MC-A

NOTE:

When the system is disarmed with theinterior light switched to "DOOR", theinterior light will illuminate for 30 sec-onds.UNLOCK



23/283

Battery

1KMA2003

Replacement instructions:

1. Carefully separate the case with ablade screwdriver.

2. Remove the old battery from the caseand note the polarity. Make sure thepolarity of the new battery is thesame(+side facing up), then insert it inthe transmitter.

WINDOW GLASS

!

3FDA2015

B050A01A-AAT

To raise or lower the window, turn thewindow regulator handle clockwise orcounterclockwise.

WARNING:

When opening or closing the windows,make sure your passenger's arms,hands and body are safely out of the way.

B060A02MC-AAT

POWER WINDOWS (If Inst

The power windows operate whnition key is in the "ON" positionswitches are located on the driveand control the front (4/3 Doorwindows (4Door) on both sideshicle. The windows may be odepressing the appropriate windand closed by pulling up the open the window on the driver's the switch(1) halfway down. Thmoves as long as the switch is opfully open the driver's window

cally, press the switch fully dow

4 Door



24/283

112

! WARNING:o Passengers can be injure

head, hands or other bodytrapped by a closing winways check for obstructioraising any window.

o NEVER leave the ignition vehicle.

o NEVER leave any child unin the vehicle. Even vechildren may inadvertentlyvehicle to move, entangselves in the windows, or injure themselves or othe

o Do not attempt to operateswitch on the driver's doswitch on another door in directions at the same timedone, the window will stop

not be opened or closed.OMC025015

NOTE:

The power windows can be operated for30 seconds after the ignition key isturned to the "ACC" or "LOCK" posi-tions, or removed from the ignitionswitch. If the front doors are openedduring this 30 second period, the powerwindows can no longer be operated with-

out the ignition key turned to the "ON"position.

In order to prevent operation of the pas-senger front (4/3 Door) and rear windows(4Door), a window lock switch(2) is pro-vided on the armrest of the driver's door.To disable the power windows, press thewindow lock switch. To revert to normaloperation, press the window lock switcha second time.

B060A02MC

In automatic operation, the window will fully

open even if you let go of the switch. To stopat the desired opening, pull up and releasethe switch.

CLOSE

OPEN



25/283

SEATS

B080A01MC-AAT

B080A01MC-A

Drivers seat

1. Seat forward/rearward lock lever

2. Seatback recliner control le3. Seat cushion height control

Front passengers seat

4. Seat forward/rearward lock lever

5. Seatback recliner control le

Rear seats

6. Seatback folding lever (If I7. Armrest (If Installed)

4 Door

3 Door



26/283

14

B080C02A-AAT

Adjusting Seatback Angle

To move the seat toward the front or rear,pull the lock release lever upward. Thiswill release the seat on its track so youcan move it forward or rearward to the

desired position.When you find the position you want,release the lever and slide the seat for-ward or rearward on its track until it locksinto the desired position and cannot bemoved further.

OMC025026

! WARNING:After adjusting the seat, alwathat it is securely locked intoattempting to move the seat foreverse without using the loclever. Sudden or unexpecte

ment of the driver's seat couyou to lose control of the vehicing in an accident.

B080B03A-AAT

FRONT SEATSAdjusting Seat Forward and Rear-

ward! WARNING:o Never adjust the drivers seat while

the vehicle is moving. Any suddenor unexpected movement of the seatcould cause you to lose control ofthe vehicle resulting in an accident.Only adjust the drivers seat whenthe vehicle is stationary.

o Do not sit or lean unnecessarily closeto the airbag. Position the seat so

that you can sit as far back as pos-sible from the airbag and still com-fortably reach all controls.

B080A01FC-AAT

ADJUSTABLE SEATS



27/283

To recline the seatback, lean forward to

take your weight off it, then pull up on therecliner control lever at the outside edgeof the seat. Now lean back until the de-sired seatback angle is achieved. To lockthe seatback into position, release therecliner control lever.

! WARNING:Riding with a reclined seatback in-creases your chance of serious or fatalinjuries in the event of a collision or

sudden stop. The protection of yourrestraint system (seat belts and airbags)is greatly reduced by reclining your seat.Seat belts must be snug against yourhips and chest to work properly. Themore the seatback is reclined, the greaterthe chance that an occupant's hips will

slide under the lap belt or the occupant'sneck will strike the shoulder belt. Driv-ers and passengers should always sitwell back in their seats, properly belted,and with the seatbacks upright.

B080D02JM-AAT

Adjustable Headrests

Headrests are designed to help reducethe risk of neck injuries.To raise the headrest, pull it up. To lowerthe headrest, push it down while press-ing the lock knob. To remove the head-rest, raise it as far as it can go then press

the lock knob while pulling upward. Thisshould only be done when the seat is notoccupied.

B080D02MC

Lock knob

! WARNING:

o For maximum effectivenesof an accident, the headrebe adjusted so the middheadrest is at the same heitop of the occupant's eyes

of a cushion that holds away from the seatback isommended.

o Do not operate the vehicleheadrests removed as sevto an occupant may occevent of an accident. Head

provide protection againneck injuries when properly



28/283

16

B130A01A-AAT

REAR SEAT ENTRY (3 Doo

The front passenger's seatbabe tilted to enter the rear seatBy pulling up on the recliner co(1) at the outside of the front paseat, the seatback will tilt forwaseat will automatically slide fo

Rear seat occupants can tiltpassenger's seatback by deprfoot lever (2) as shown in the i

(2)

! WARNING:

B080F01S-AAT

Seat Cushion Height Adjustment(Driver's Seat only)

To raise or lower the front part of the seatcushion, turn the front knob forward orrearward. To raise or lower the rear partof the seat cushion, turn the rear knob

forward or rearward.

B080F01MC

B080G01A-GAT

Adjusting Armrest Angle(Driver's side only)

The armrest will be raised or loweredmanually.To raise the armrest, pull it up.To lower it, press the armrest down.

OMC025031

o Do not adjust the headrest heightwhile the vehicle is in motion.



29/283

! WARNING:Passengers sitting in the rear seat shouldbe careful not to accidentally press thefoot lever (2) while the vehicle is moving,as this may cause the seatback to moveforward and injure a front seat occupant.

B085A01MC-GAT

REAR SEAT

Adjusting seatback angle (3 Door)

To recline the seatback, pull up the

seatback folding lever (1) and push theseatback rearward.

B085A01MC

(1)

To return the seatback to an upright po-

sition, pull up the seatback folding lever(1) and pull the seatback forward until theseatback locks into upright position.After adjusting the seatback angle, al-ways check that it is securely locked intoplace.

! WARNING:Do not adjust the seatback angle whilethe vehicle is in motion.

Lock Knob

B085D01TG-AAT

Adjustable Headrests

(If Installed)

B090A01MC

Headrests are designed to he

the risk of neck injuries.To raise the headrest, pull it upthe headrest, push it down whilthe lock knob. To remove theraise it as far as it can go thenlock knob while pulling upwshould only be done when the

occupied.

! WARNING:o For maximum effectivenes

of an accident, the headrebe adjusted so the middheadrest is at the same heitop of the occupant's eyesof a cushion that holds away from the seatback isommended.

o Do not operate the vehicleheadrests removed as sevto an occupant may occevent of an accident. Headprovide protection againneck injuries when properly



30/283

18

o Before folding the seatbathe buckle in the pocket. prevent the buckle from beaged by seatback.

!

B110A01MC-AAT

Folding Rear Seatbacks (4Door)

The rear seatbacks may be folded tofacilitate carrying long items or to increasethe luggage capacity of the vehicle.

WARNING:The purpose of the fold-down rearseatbacks is to allow you to carry longerobjects than could otherwise be accom-modated.Never allow passengers to sit on top ofthe folded down seat back while the caris moving as this is not a proper seatingposition and no seat belts are availablefor use. This could result in serious in-jury or death in case of an accident orsudden stop. Objects carried on thefolded down seatback should not extend

higher than the top of the front seats.This could allow cargo to slide forwardand cause injury or damage during sud-den stops.

To fold down the seatback :

1. Slide forward and upright the frontseats before folding down.

2. Lower the headrests to the lowestposition.

B220D05MC

o In order to prevent the center shoul-der belt from being damaged whilefolding the rear seat, disconnect themetal tab (A) from the buckle (B). Todisconnect the metal tab (A) from

the buckle (B) , insert a narrow-endedtool into the groove located on thebuckle(B).

! CAUTION:



31/283

B090A02MC

3. Pull up the seatback locking knob,

then fold the seat toward the front ofthe vehicle.

! CAUTION:

o Move the rear lap/shoulder belt tothe outside so that they don't inter-fere with the seatback when folding.

o Move the rear lap/should

the side so that it is cleseatback when returning right position.

o Place the rear seat belt to tposition.

OMC025039



32/283

20

To fold seatback down a

cushion up :1. Slide the front seats forward

the seatbacks upright befothe rear seatback and cush

!

B080G01MC-AAT

Folding Rear Seatback and Seat

Cushion (3 Door)

For greater convenience, the entireseatback may be folded down and theseat cushion may be folded up.

WARNING:The purpose of the fold-down rear seatback and the fold-up rear seat cushion isto allow you to carry more objects thancould be accommodated. Do not allow

passengers to sit on the cargo areawhile the car is moving. This is not aproper seating position and no seat beltsare available for use when the seat backis folded down. This could result in seri-ous injury or death in case of an accidentor a sudden stop. Objects should not

extend higher than the top of the frontseatbacks. This could allow cargo toslide forward and cause injury or dam-age during sudden stops.

! WARNING:When you return the rear seatback to its

upright position after being folded down:Be careful not to damage the seat beltwebbing or buckle. Do not allow the seatbelt webbing or buckle to get caught orpinched in the rear seat. Ensure that theseatback is completely locked into its

upright position by pushing on the top ofthe seaback. Otherwise, in an accidentor sudden stop, the seat could fold downand allow cargo to enter the passengercompartment, which could result in se-rious injury or death.

When you return the seatback to its up-

right position, always be sure it has lockedinto position by pushing on the top of theseatback.

CAUTION:!

o In order to prevent the cender belt from being damafolding the rear seat, discometal tab (A) from the buckdisconnect the metal tab

the buckle (B) , insert a narrtool into the groove locatbuckle(B).



33/283

B080G01MC

o Before folding the seatback, insert

the buckle in the pocket. This canprevent the buckle from being dam-aged by seatback.

B090A03MC

2. Pull the strap of the seat cushion up-

ward to fold up the seat cushion.3. Fold up the seat cushion.

4. Remove and put the head

loops on backside of the sea

5. Pull the seatback locking knseatback to fold-down the s

1FEATURES OF YOUR HYUNDAISEAT BELTS


34/283

22 SEAT BELTS

B140A01S-AAT

REAR SEAT WARNING

For the safety of all passengers, luggageor other cargo should not be piled higherthan the top of the seatback. In addition,

do not place objects on the rear shelf asthey may move forward during braking orin an accident and strike vehicle passen-gers.

B140A01MC

!!

B150A02S-AAT

SEAT BELT PRECAUTION

WARNING:All occupants of the vehicle mtheir seat belts at all times. Sand child restraints reduce t

serious or fatal injuries for all oin the event of a collision or sudWithout a seat belt, occupantsshifted too close to a deployinstrike the interior structure or from the vehicle. Properly wbelts greatly reduce these hazawith advanced airbags, unbepants can be severely injuredploying airbag. Always followcautions about seat belts, airoccupant safety containedmanual.

6. Fold down the seat back forward.

B090A06MC

!

When you return the seatback and seatcushion to its original position, always besure it has locked into position by push-ing on the top of the seatback.

WARNING:When you return the rear seatback andseat cushion to its original position , becareful not to damage the seat belt web-bing or buckle. In addition, do not allow

the seat belt webbing or buckle to getcaught or pinched in the rear seat.



35/283

!

B150B03A-AAT

Infant or Small Child

All 50 states have child restraint laws.You should be aware of the specific re-quirements in your state. Child and/orinfant safety seats must be properly placedand installed in the rear seat. Informationabout the use of these restraints beginson page 1-31.

WARNING:Every person in your vehicle needs to be

properly restrained at all times, includ-ing infants and children. Never hold achild in your arms or lap when riding in avehicle. The violent forces created dur-ing a crash will tear the child from yourarms and throw the child against theinterior. Always use a child restraint

appropriate for your child's height andweight, see page 1-31.

NOTE:

Small children are best protected frominjury in an accident when properly re-strained in the rear seat by a child re-straint system that meets the require-ments of the Federal Motor VehicleSafety Standards. Before buying anychild restraint system, make sure that it

has a label certifying that it meets MotorVehicle Safety Standard 213. The re-straint must be appropriate for yourchild's height and weight. Check the la-bel on the child restraint for this informa-tion. See page 1-31.

B150C02A-AAT

Larger Children

Children who are too large fostraint systems should always orear seat and use the avashoulder belts. The lap portion fastened snug on the hips andpossible. Check belt fit periochild's squirming could put the position. Children are affordedsafety in the event of an accidthey are restrained by a propesystem in the rear seat. If a la(over age 13) must be seated i

seat, the child should be sestrained by the available lapbelt and the seat should be plarearmost position. Children undof 13 should be restrained securear seat. NEVER place a cthe age of 13 in the front sea

place a rear facing child seat iseat of a vehicle.



36/283

24

!

B150F01A-AAT

One Person Per Belt

Two people (including children) shouldnever attempt to use a single seat belt.This could increase the severity of inju-ries in case of an accident.

B150G02A-AAT

Do Not Lie Down

To reduce the chance of injuries in theevent of an accident and to achieve maxi-mum effectiveness of the restraint sys-

tem, all passengers should be sitting upand the front seats should be in an up-right position when the car is moving. Aseat belt cannot provide proper protec-tion if the person is lying down in the rearseat or if the front seat is in a reclined

position.

WARNING:Riding with a reclined seacreases your chance of serioinjuries in the event of a cosudden stop. The protectiorestraint system (seat belts an

is greatly reduced by recliningSeat belts must be snug agahips and chest to work propmore the seatback is reclined, tthe chance that an occupant'slide under the lap belt causininternal injuries or the occupacould strike the shoulder beland passengers should alwaback in their seats, properly bpage 1-26), and with the seatright.

B150D01A-AAT

Pregnant Women

The use of a seat belt is recommended forpregnant women to lessen the chance ofinjury in an accident. When a seat belt isused, the lap belt portion should beplaced as low and snugly as possible onthe hips, not across the abdomen. Forspecific recommendations, consult a phy-sician.

B150E01A-AAT

Injured PersonA seat belt should be used when aninjured person is being transported. Whenthis is necessary, you should consult aphysician for recommendations.



37/283

!

B160A02A-AAT

CARE OF SEAT BELTS

Seat belt systems should never be disas-sembled or modified. In addition, careshould be taken to assure that seat beltsand belt hardware are not damaged byseat hinges, doors or other abuse.

WARNING:When you return the rear seatback to itsupright position after the rear seatbackwas folded down, be careful not to dam-

age the seat belt webbing or buckle. Besure that the webbing or buckle does notget caught or pinched in the rear seat. Aseat belt with damaged webbing or bucklewill not be as strong and could possiblyfail during a collision or sudden stop,resulting in serious injury.

B160D01A-AAT

When to Replace Seat Belts

Entire in-use seat belt assemblies shouldbe replaced if the vehicle has been in-volved in an accident. This should bedone even if no damage is visible. Addi-tional questions concerning seat beltoperation should be directed to your

Hyundai Dealer.

B160C01A-AAT

Keep Belts Clean and Dry

Seat belts should be kept clean and dry.If belts become dirty, they can be cleanedby using a mild soap solution and warm

water. Bleach, dye, strong detergents orabrasives should not be used becausethey may damage and weaken the fabric.

B170A02MC-AAT

HEIGHT ADJUSTABLE FRO

SHOULDER BELT

You can adjust the height of thbelt anchor to one of the 4 pomaximum comfort and safety.If the height of the adjusting stoo near your neck, you will not

the most effective protection. Tder portion should be adjustedlies across your chest and miyour shoulder nearest the dooyour neck. To adjust the height belt anchor, lower or raise tadjuster into an appropriate po

raise the height adjuster, pull

B160B01A-AAT

Periodic Inspection

It is recommended that all seat belts beinspected periodically for wear or dam-age of any kind. Parts of the system thatare damaged should be replaced as soonas possible.


26


38/283

26

To fasten your seat belt, pull itretractor and insert the metal tabuckle. There will be an audwhen the tab locks into the bu

The seat belt automatically adjproper length only after the ladjusted manually so that it faround your hips. If you lean foslow, easy motion, the belt wand let you move around. If sudden stop or impact, howevewill lock into position. It will alsotry to lean forward too quickly

B180A01MC-AAT

SEAT BELT-Driver's 3-Poin

with Emergency Locking R

To Fasten Your Belt

o If the shoulder belt anchor is not

moved, grasp the shoulder part ofthe belt and pull forward to the full.

!WARNING:o Verify the shoulder belt anchor is

locked into position at the appropri-ate height. Never position the shoul-der belt across your neck or face.Improperly positioned seat belts cancause serious injuries in an acci-

dent.o Failure to replace seat belts after an

accident could leave you with dam-aged seat belts that will not provideprotection in the event of anothercollision leading to personal injury ordeath. Replace your seat belts afterbeing in an accident as soon as pos-sible.

To lower it, push it down while pressing

the height adjuster button. Release thebutton to lock the anchor into position. Trysliding the height adjuster to make surethat it has locked into the position.

OMC025042-1

! CAUTION:o Adjust the shoulder belt height whenyou sit well back in the seat.

o When adjusting the shoulder beltheight, grip the height adjuster but-ton securely and slide the height

adjuster up or down.



39/283

NOTE:If the seat belt is not fastened when theignition key is turned from the "OFF"position to the "ON" position, the seatbelt warning will activate to remind thedriver to fasten the seat belt as follows.

The driver's seat belt warning light andchime will activate to the following tablewhen the ignition switch is in "ON" posi-tion.

B265E01MC-AAT

Seat Belt Warning Light

and Chime

Conditions Warning Pattern

Seat Belt Vehicle Speed Light-Blink Chime-Sound

Unbuckled

Buckled

BuckledUnbuckled

Unbuckled

Above 6mph(10 km/h)

Below 3mph

(5 km/h)

6 seconds

6 seconds

6 seconds *1)

Stop *2)

6 seconds None

B190A03A-AAT

SEAT BELTS-Front Passe

Rear Seat 3-Point System wbination Locking Retracto

To Fasten Your Belt

Combination retractor type seainstalled in the rear seat outb

center positions to help accothe installation of child restrainHyundai strongly recommendsdren always be seated in theNEVER place any infant restrain the front seat of the vehicleThis type of seat belt combine

tures of both an emergency ltractor seat belt and an automaretractor seat belt. To fasten belt, pull it out of the retractor the metal tab into the buckle. be an audible "click" when the

into the buckle. When not securrestraint, the seat belt operasame way as the driver's seat bgency Locking Retractor Typematically adjusts to the proper lafter the lap belt portion of the sadjusted manually so that it f

around your hips.

*1) Warning pattern repeats 11 times withinterval 24 seconds. If the driver's seat

belt is buckled, the light will stop within6 seconds and chime will stop imme-diately.

*2) The light will stop within 6 secondsand chime will stop immediately.


28


40/283

28

! WARNING:

!

B200A01A-AAT

Adjusting Your Seat Belt

WARNING:You should place the lap belt plow as possible and snugly achips, not on your waist. If the

located too high on your waincrease the chance of injury inof a collision. Both arms shounder or over the belt. Rather, obe over and the other under, asthe illustration.Never wear the seat belt unde

nearest the door.

o Children age 12 and younger mustalways be properly restrained in therear seat. Never allow children toride in the front passenger seat. If achild over 13 must be seated in the

front seat, he/she must be properlybelted and the seat should be movedas far back as possible.

o Never wear the shoulder belt underyour arm or behind your back. Animproperly positioned shoulder beltcan cause serious injuries in a crash.The shoulder belt should be posi-tioned midway over your shoulderacross your collarbone.

o Avoid wearing twisted seat belts. Atwisted belt can't do its job as well. Ina collision, it could even cut into you.

Be sure the belt webbing is straightand not twisted.o Be careful not to damage the belt

webbing or hardware. If the belt web-bing or hardware is damaged, re-place it.

When the seat belt is fully extended from

the retractor to allow the installation of achild restraint system, the seat belt opera-tion changes to allow the belt to retract,but not to extend (Automatic LockingRetractor Type). See page 1-37.

NOTE:

Although the combination retractor pro-vides the same level of protection forseated passengers in either emergencyor automatic locking modes, it is recom-mended that seated passengers use theemergency locking feature for improvedconvenience. The automatic locking

function is intended to facilitate childrestraint installation. To convert fromthe automatic locking feature to theemergency locking operation mode, al-low the unbuckled seat belt to fully re-tract.

! WARNING:o For maximum restraint system pro-

tection, seat belts must always beused whenever the car is moving.

o Seat belts are most effective whenseatbacks are in the upright posi-tion.



41/283

B210A01A-AAT

To Release the Seat Belt

The seat belt is released by pressing therelease button in the locking buckle. Whenit is released, the belt should automati-cally draw back into the retractor.If this does not happen, check the belt tobe sure it is not twisted, then try again.

B210A01NF

B220D02MC-AAT

SEAT BELTS - Rear Seat Center 3-

Point System With Emergency Lock-ing Retractor

1. Before fastening the rear seat centerbelt, confirm the metal tab (A) andbuckle (B) are latched together.

B220D01MC

2. After confirming that (A) an

latched, pull the seat belt retractor and insert the metinto the buckle (D).


30


42/283

30

! WARNING:o Never let anyone ride incenter seat without fastmetal tabs and buckles as in this section. This sedesigned to function as a

point restraint (lap/shoulUsing only the shoulder plap portion of the belt canserious or fatal injuries inof a collision or sudden st

o Never unlock the metal tathe buckle (B) with the foll

ceptions.(1) In case of folding rear s

down.(2) If transporting an obje

rear seat may cause dthe rear seat center be

B220D04MC

There will be an audible "click" when the

tab locks in the buckle. The seat beltautomatically adjusts to the proper lengthonly after the lap belt is adjusted manu-ally so that it fits snugly around your hips.If you lean forward in a slow, easy motion,the belt will extend and let you movearound. If there is a sudden stop or im-

pact, the belt will lock into position. It willalso lock if you try to lean forward tooquickly.

NOTE:Confirm the metal tab and the bucklemarked "CENTER" are latched together.

B220D03MC


CHILD RESTRAINT SY


43/283

!

B220D05MC

To disconnect the metal tab (A) from thebuckle (B), insert a narrow-ended toolinto the groove located on the buckle (B).

WARNING:Always lock metal tab (A) into buckle (B)immediately after returning the rearseatbacks to an upright position. Thisportion of the rear center seat belt shouldonly be unbuckled when the rearseatback is folded down.

!

B220C02A-GAT

To Release the Seat Belt

When you want to release the seat belt,press the button in the locking buckle.

WARNING:

When fastening the outboard seat beltsor the center seat belt, make sure theyare inserted into the correct buckles toobtain maximum protection from the seatbelt system and assure proper opera-tion.

B210A01NF

B230A03A-AAT

Children riding in the car shoulrear seat and must always brestrained to minimize the risk an accident, sudden stop omaneuver. According to accidtics provided by the NationaTraffic Safety Administration

children are safer when prostrained in the rear seats than iseat. Larger children not in astraint should use one of the provided.All 50 states have child restrYou should be aware of the squirements in your state. Chinfant safety seats must be propand installed in the rear seat. use a commercially availablestraint system that meets the reqof the Federal Motor Vehicle Sa

dards (FMVSS).Children could be injured or crash if their restraints are nosecured. For small children andchild seat or infant seat must


32


44/283

!o Never hold a child in your a

when riding in a vehicle. Tforces created during a tear the child from your throw the child against the

rior.o Never put a seat belt ove

and a child. During a crascould press deep into the cing serious internal injurie

o Never leave children unattvehicle not even for a sThe car can heat up verresulting in serious injuridren inside. Even very ydren may inadvertently cvehicle to move, entangselves in the windows, or l

selves or others inside tho Never allow two children, opersons, to use the same

o Children often squirm and themselves improperly. Nchild ride with the shouldeder their arm or behind t

Always properly position achildren in rear seat.

WARNING:o When the child restraint system is

not in use, store it in the trunk orfasten it with a safety belt so that itwill not be thrown forward in case ofa sudden stop or an accident.

o Children may be seriously injured orkilled by an inflating airbag. All chil-dren, even those too large for childrestraints, must ride in the rear seat.

To reduce the chance or serious or fatalinjuries:

o Children of all ages are safer whenrestrained in the rear seat. A childriding in the front passenger seatcan be forcefully struck by an inflat-ing airbag resulting in serious or fa-tal injuries.

o Always follow the instructions forinstallation and use of the child re-straint maker.

o Always make sure the child seat issecured properly in the car and yourchild is securely restrained in thechild seat.

! WARNING:

WARNING:o A child restraint system must be

placed in the rear seat. Never installa child or infant seat on the frontpassenger's seat.Should an accident occur and causethe passenger side airbag to deploy,it could severely injure or kill aninfant or child seated in an infant orchild seat. Thus, only use a childrestraint in the rear seat of yourvehicle.

o Since a safety belt or child restraintsystem can become very hot if it isleft in a closed vehicle, be sure tocheck the seat cover and bucklesbefore placing a child there.

!

Before buying a particular child restraintsystem, make sure it fits your car seat andseat belts, and fits your child. Follow allthe instructions provided by the manufac-turer when installing the child restraintsystem.



45/283

! WARNING:o Never allow a child to stand-up or

kneel on the seat or floorboard of amoving vehicle. During a collision orsudden stop, the child can be vio-lently thrown against the vehicles

interior, resulting in serious injury.o Never use an infant carrier or a child

safety seat that "hooks" over aseatback, it may not provide ad-equate security in an accident.

o Seat belts can become very hot, es-pecially when the car is parked in

direct sunlight. Always check seatbelt buckles before fastening themover a child.

o Always store or secure a child seat,even when it is not in use. During acollision or sudden stop, the child

seat could be thrown inside the ve-hicle.

B230B01E-AAT

Using a Child Restraint System with

the "Tether Anchorage" System

For small children and babies, the use ofa child seat or infant seat is required. Thischild seat or infant seat should be ofappropriate size for the child and shouldbe installed in accordance with themanufacturer's instructions. It is furtherrequired that the seat be placed in thevehicle's rear seat since this can make animportant contribution to safety. Your ve-hicle is provided with three child restrainthook holders for installing the child seat

or infant seat.

B230C02MC-AAT

Installing a Child Restraint

the "Tether Anchorage" Sy(4 Door)

Three child restraint hook holocated on the rear seat packa

To install the child restrain

1. Open the tether anchor covrear seat package tray.


34


46/283

B230E02MC-AAT

Installing a Child Restraint

the "Tether Anchorage" (3 Door)

Three child restraint hook holocated on the rear floor pane

To install the child restrain

! WARNING:o A child can be seriously injured or

killed in a collision if the child re-straint is not properly anchored.Always follow the child seatmanufacturers instructions for in-

stallation and use.o Never mount more than one child

restraint to a single tether or to asingle lower anchorage point. Theincreased load caused by multipleseats may cause the tethers or an-chorage points to break, causing

serious injury or death.

1. Open the tether anchor covrear floor panel.

2. Route the child restraint seat strapover the seatback.For vehicles with adjustable headrests,route the tether strap under the head-rest and between the headrest posts,otherwise route the tether strap overthe top of the seatback.

3. Connect the tether strap hook (2) to the

child restraint hook holder (1) andtighten to secure the seat.

B230C02MC



47/283

B230C02MC

2. Route the child restraint seat strapover the seatback.For vehicles with adjustable headrests,route the tether strap under the head-rest and between the headrest posts,otherwise route the tether strap overthe top of the seatback.

3. Connect the tether strap hook (2) to the

child restraint hook holder (1) throughthe hole on the covering shelf andtighten to secure the seat.

! WARNING:o A child can be seriously injured or

killed in a collision if the child re-straint is not properly anchored.Always follow the child seatmanufacturers instructions for in-

stallation and use.o Never mount more than one child

restraint to a single tether or to asingle lower anchorage point. Theincreased load caused by multipleseats may cause the tethers or an-chorage points to break, causing

serious injury or death.

B230D05E-AAT

Securing the Child Restra

with the "ISOFIX" System

Some child seat manufactursafety seats that are labeled asISOFIX-compatible child seaseats include two rigid ormounted attachments that con

ISOFIX anchors at specific setions in your vehicle. This typseat eliminates the need to useto attach the child seat for forwchild seats.


36


48/283

The ISOFIX anchors are locatethe seatback and the seat cushrear seat left and right outboapositions.

ISOFIXAnchor

ISOFIX

Position!o Never mount more than one childrestraint to a single tether or to asingle lower anchorage point. Theincreased load caused by multipleseats may cause the tethers or an-

chorage points to break, causingserious injury or death.o When using the vehicles "ISOFIX"

system to install a child restraintsystem in the rear seat, all unusedvehicle rear seat belt metal latchplates or tabs must be latched se-

curely in their seat belt buckles andthe seat belt webbing must be re-tracted behind the child restraint toprevent the child from reaching andtaking hold of unretracted seat belts.Unlatched metal latch plates or tabsmay allow the child to reach theunretracted seat belts which mayresult in strangulation and a seriousinjury or death to the child in the childrestraint.

WARNING:

WARNING:o A child can be seriously injured or

killed in a collision if the child re-straint is not properly anchored.

Always follow the child seatmanufacturers instructions for in-stallation and use.

o Never install a child restraint usingthe ISOFIX anchors at the center po-sition of the rear seat. In a crash, theISOFIX anchors may break if a car

seat is improperly placed in the cen-ter position resulting in serious orfatal injuries. Only place a ISOFIX orISOFIX-compatible child seat in theleft or right out-board rear seatingpositions (as shown) to the appropri-ate ISOFIX anchors provided.

!

ISOFIX anchors have been provided inyour vehicle. The ISOFIX anchors arelocated in the left and right outboard rearseating positions. Their locations areshown in the illustration. There is noISOFIX anchor provided for the centerrear seating position.



49/283

Follow the child seat manufacturer's in-structions to properly install safety seatswith ISOFIX or ISOFIX-compatible attach-ments.

Once you have installed the ISOFIX childrestraint seat, assure that the seat is prop-erly attached to the ISOFIX and tether

anchors. Also, test the safety seat beforeyou place the child in it. Tilt the seat fromside to side. Also try to tug the seat for-ward. Check to see if the anchors hold theseat in place.

! WARNING:A child can be seriously injured or killedin a collision if the child restraint is notproperly anchored to the car and thechild is not properly restrained in thechild restraint. Always follow the childseat manufacturers instructions for in-stallation and use.

B230F01A-AAT

Child Restraint System Installation

on Rear Seat Center Position

Use the center seat belt for the rear seatto secure the child restraint system asillustrated. After installation of the childrestraint system, rock the child seat backand forth, and side to side to ensure that

it is properly secured by the seat belt. Ifthe child seat moves, readjust the lengthof the seat belt. Then, if equipped, insertthe child restraint tether strap hook intothe child restraint hook holder and tightento secure the seat. Always refer to thechild restraint system manufacturer's rec-

ommendation before installing the childrestraint system in your vehicle.

B230F02MC

To install a child restraint systoutboard rear seats, extend thelap belt entirely from its retrac"click" is felt. This will engage thretractor automatic locking feat

allows the seat belt to retracextend. Install the child restraibuckle the seat belt and allowbelt to take up any slack. Makethe lap portion of the belt is tigthe child restraint system and der portion of the belt is position

it cannot interfere with the childneck. Also, double check to be

B230G02MC-AAT

Child Restraint System Ins

on Outboard Rear Seats


38


50/283

B180C02MC-AAT

Pre-Tensioner Seat Belt

Your Hyundai vehicle is equidriver's and front passengtensioner seat belts. The purppre-tensioner is to make sureseat belts fit tightly against the obody in certain frontal collisions

tensioner seat belts can be activor, where the frontal collision enough, together with the airb

! WARNING:o If the retractor is not in the Auto-matic Locking mode, the child re-straint can move when your vehicleturns or stops suddenly. A child canbe seriously injured or killed if the

child restraint is not properly an-chored to the car, including settingthe retractor to the Automatic Lock-ing mode.

o Do not install any child restraint sys-tem in the front passenger seat.Should an accident occur and cause

the passenger side airbag to deploy,it could severely injure or kill aninfant or child seated in an infant orchild seat. Therefore, only use a childrestraint system in the rear seat ofyour vehicle.

o Before installing Child Restraint Sys-tem to vehicles fitted with CurtainAirbags, always refer to safety no-tices for Curtain Airbag systems onthis manual. Whenever installing childrestraints, use only approved devicesand refer to "Child Restraint System"

to ensure correct installation and oc-cupant protection is maximized.

the retractor has engaged the automaticlocking feature by trying to extend web-bing out of the retractor. If the retractor isin the automatic locking mode, the beltwill be locked. After installation of thechild restraint system, try to move it in alldirections to be sure the child restraintsystem is securely installed. If you need

to tighten the belt, pull more webbingtoward the retractor. When you unbucklethe seat belt and allow it to retract, theretractor will automatically revert back toits normal seated passenger emergencylocking usage condition.

NOTE:o Before installing the child restraint

system, read the instructions sup-plied by the child restraint systemmanufacturer.

o If the seat belt does not operate asdescribed, have the system checkedimmediately by your authorizedHyundai dealer.



51/283

The seat belt pre-tensioner system con-sists mainly of the following components.Their locations are shown in the illustra-tion.

1. SRS airbag warning light2. Seat belt pre-tensioner assembly

3. SRS control module

When the vehicle stops suddenly, or if theoccupant tries to lean forward too quickly,the seat belt retractor will lock into posi-tion. In certain frontal collisions, the pre-tensioner will activate and pull the seatbelt into tighter contact against theoccupant's body.

Passenger'sairbag

B180D01MC

Driver's airbag 1

23

NOTE:o Both the driver's an

passenger's pre-tensioner will be activated in certacollisions. The pre-tensiobelts can be activated where the frontal collisionenough, together with the

The pre-tensioners will novated if the seat belts are worn at the time of the col

o When the pre-tensioner sare activated, a loud noisheard and fine dust, whichpear to be smoke, may be

the passenger compartmeare normal operating condare not hazardous.

o Although it is harmless, themay cause skin irritation anot be breathed for prolonods. Wash your hands andoughly after an accident in pre-tensioner seat belts wvated.

! WARNING:To obtain maximum benefit from a pre-tensioner seat belt:

The seat belt must be work correctly andadjusted to the proper position (see

pages 1-25 and 1-26). Please read andfollow all of the important informationand precautions about your vehiclesoccupant safety features including seatbelts and advanced airbags that areprovided in this manual.


40


52/283

!! WARNING:o Pre-tensioners are designed to op-erate only one time. After activation,pre-tensioner seat belts must bereplaced. All seat belts, of any type,should always be replaced after they

have been worn during a collision.o The pre-tensioner seat belt assem-bly mechanisms become hot duringactivation. Do not touch the pre-tensioner seat belt assemblies forseveral minutes after they have beenactivated.

o Do not attempt to inspect or replacethe pre-tensioner seat belts your-self. This must be done by an autho-rized Hyundai dealer.

o Do not strike the pre-tensioner seatbelt assemblies.

o Do not attempt to service or repairthe pre-tensioner seat belt system inany manner.

o Improper handling of tensioner seat belt assemfailure to heed the warninstrike, modify, inspect, repvice or repair the pre-tensi

belt assemblies may lead ter operation or inadvertetion and serious injury.

o Always wear the seat bedriving or riding in a moto

WARNING:CAUTION:o The sensor that activates the SRS

airbag is connected with the pre-tensioner seat belt. The SRS airbagwarning light on the instrumentpanel will illuminate for approximately

6 seconds after the ignition key hasbeen turned to the "ON" position,and then it should turn off.

o If the pre-tensioner seat belt is notworking properly, this warning lightwill illuminate even if there is no mal-function of the SRS airbag.

If the SRS airbag warning light doesnot illuminate when the ignition keyis turned to the "ON" position, re-mains illuminated after approxi-mately 6 seconds when the ignitionkey is turned to the "ON" position, orif it illuminates while the vehicle isbeing driven, have an authorizedHyundai dealer inspect the advancedSRS airbag system as soon as pos-sible.

!


ADVANCED SUPPLEMENTAL RESTRAINT (AIRBAG) SYSTEM (SRS)


53/283

B240D01MC-AAT

(If Installed)

1. Driver's front airbag2. Passenger's front airbag3. Side impact airbag4. Curtain airbag

B240D01MC


42


54/283

B240A01MC

The purpose of the SRS is to provide thevehicle's driver and/or the front passen-ger with additional protection than thatoffered by the seat belt system alone incase of a frontal impact of sufficient sever-ity. The SRS uses sensors to gather infor-mation about the driver's and frontpassenger's seat position, the driver's and

front passenger's seat belt usage andimpact severity.

The driver's and front passenger's seattrack position sensors, which are installedon the seat track, determine if the seatsare fore or aft of a reference position. The

seat belt buckle sensors determine if thedriver and front passenger's seat beltsare fastened. These sensors provide theability to control the SRS deploymentbased on how close the driver's seat is tothe steering wheel, how close thepassenger's seat is to the instrumentpanel, whether or not the seat belts arefastened, and how severe the impact is.

The advanced SRS offers thecontrol the airbag inflation witels. A first stage level is promoderate-severity impacts. stage level is provided for moimpacts.

According to the impact severi

position and seat belt usSRSCM(SRS Control Modulethe airbag inflation. Failure towear seat belts can increase severity of injury in an acciden

Additionally, your Hyundai is

with an occupant classificationthe front passenger's seat. Theclassification system detects ence of a passenger in passenger's seat and will turn opassenger's airbag under certtions. For more detail, see "Occusification System" later in this

B240A02NF-AAT

Driver's and Passenger's Front

Airbag

Your Hyundai is equipped with an ad-vanced Supplemental Restraint (Airbag)System. The indications of the system'spresence are the letters "SRS AIRBAG"embossed on the airbag pad cover in thesteering wheel and the passenger's sidefront panel pad above the glove box.

The Hyundai SRS consists of airbagsinstalled under the pad covers in thecenter of the steering wheel and thepassenger's side front panel above the

glove box.

Driver's Front Airbag



55/283

CAUTION:If a seat track position sensor or anoccupant classification system is notworking properly, the SRS airbag warn-ing light on the instrument panelwill illuminate because the SRS airbagwarning light is connected with the seattrack position sensor and the occupantclassification system. If the SRS airbagwarning light does not illuminate whenthe ignition key is turned to the "ON"position, remains illuminated after ap-proximately 6 seconds when the ignition

key is turned to the "ON" position, or if itilluminates while the vehicle is beingdriven, have an authorized Hyundaidealer inspect the advanced SRS airbagsystem as soon as possible.

!

AIR

BAG

! WARNING:o Modification to the seat structurecan adversely affect the seat trackposition sensor and cause the airbagto deploy at a different level thanshould be provided.

o Do not place any objects underneaththe front seats as they could dam-age the seat track position sensor orinterfere with the occupant classifi-cation system.

o Do not place any objects that maycause magnetic fields near the front

seat. These may cause a malfunc-tion of the seat track position sen-sor.

NOTE:o Be sure to read informat

the SRS on the labels prothe topside of the sun visor glove box.

o Advanced airbags are combpre-tensioner seat belts tovide enhanced occupant p

in frontal crashes. Front ainot intended to deploy in cowhich sufficient protectioprovided by the pre-tensibelt.

o If you are considering moof your vehicle due to a

please contact the Hyuntomer Assistance Center 633-5151.


44


56/283

! WARNING:o Move your seat as far back as prac-tical from the front airbags, while stillmaintaining control of the vehicle.

o Never sit or lean unnecessarily closeto the front or side airbags.

o Never lean against the door or cen-ter console always sit in an uprightposition.

o Do not allow an adult passenger toride in the front seat when the Pas-senger Airbag OFF indicator is illu-minated, because the airbag will not

deploy in the event of a moderate orsevere frontal crash.

o Never place objects over or nearany airbag module (front or side im-pact airbags), because these objectscan injure passengers in a crash.

o Never place covers, blankets oraftermarket seat warmers on thepassenger seat as these may inter-fere with the occupant classificationsystem.

! WARNING:Always use seat belts and child restraints every trip, every time, everyone!Airbags inflate with considerable forceand in the blink of an eye. Seat belts helpkeep occupants in proper position toobtain maximum benefit from the airbag.Even with advanced airbags, improp-erly and unbelted occupants can be se-verely injured when the airbag inflates.Always follow the precautions about seatbelts, airbags and occupant safety con-tained in this manual.

To reduce the chance of serious or fatalinjuries and receive the maximum safetybenefit from your restraint system:o Never place a child in any child or

booster seat in the front seat (seechild restraints 1-31).

o ABC Always Buckle Children in theback seat. It is the safest place forchildren of any age to ride.

o Front and side impact airbags caninjure occupants improperly posi-tioned in the front seats.

! WARNING:o Do not tamper or disconwiring or other componentcould result from inadvertement or failure of the airbploy in a crash.

o If the SRS airbag warningpg 1-64) remains illuminathe vehicle is being drivenauthorized Hyundai dealethe airbag system as soosible.

o Airbags can only be use

have an authorized Hyundreplace the airbag immediadeployment.

o The SRS is designed to dfront airbags only when ansufficiently severe and whpact angle is within a rangsured from the forward lonaxis of the vehicle. The fronwill not deploy in side, rear oimpacts. Additionally, the aonly deploy once. Seat beltworn at all times.



57/283

! WARNING:o No objects should be placed over ornear the airbag modules on the steer-ing wheel, instrument panel, and thefront passenger's panel above theglove box, because any such object

could cause harm if the vehicle is ina crash severe enough to cause theairbags to deploy.

o If the airbags deploy, they must bereplaced by an authorized Hyundaidealer. Deployed airbags WILL NOTinflate again and will provide no pro-

tection in subsequent collisions.o Do not tamper with or disconnect

SRS wiring or other components ofthe SRS system. Doing so couldresult in injury, due to accidentaldeployment of the airbags or by ren-dering the SRS inoperative.

o Even though your vehicle is equippedwith the occupant classification sys-tem, do not install a child restraintsystem in the front passenger seatposition. A child restraint systemmust never be placed in the front

seat.

The infant or child could binjured or killed by an airbment in case of an accide

o Children younger than 13 yalways be properly restrai

rear seat. Never allow cride in the front passengerchild over 13 must be seafront seat, he or she muserly belted and the seat moved as far back as pos

o For maximum safety prote

types of crashes, all occucluding the driver should altheir seat belts whether airbag is also provided at ing position to minimize tsevere injury or death in tha crash. Do not sit or leansarily close to the airbagvehicle is in motion.

! WARNING:! WARNING:

B240A02MC

Rear impact

Side Impact

Rollover

o Front airbags are not intended todeploy in side-impact, rear-impactor rollover crashes. In addition, frontairbags will not deploy in frontalcrashes below the deployment

threshold.

o Move your seat as far back as prac-tical from the front airbags, while stillmaintaining control of the vehicle.You and your passengers shouldnever sit or lean unnecessarily closeto the airbags. Improperly positioned

drivers and passengers can be se-verely injured by inflating airbags.


46


58/283

B240B02MC-AAT

SRS Components and Functions

The SRS consists of the following compo-nents:

1. Front Impact Sensor2. "PASSENGER AIR BAG OFF" Indicator

(Front passenger's seat only)3. SRS "AIRBAG" warning light

4. Knee Bolster5. Passenger's Airbag Module6. Driver's Airbag Module7. SRS Control Module (SRSCM)8. Occupant Classification System

(Front passenger's seat only)9. Driver's and Front Passenger's Seat

Track Position Sensors

B240B01NF

10. Driver's and Front PassenBelt Buckle Sensors

11. Side Impact Sensor (If Inst12. Retractor Pre-tensioner As13. Side Impact Airbag Module (14. Curtain Airbag Module (If

! WARNING:o Sitting improperly or out of positioncan result in serious or fatal injury ina crash. All occupants should situpright with the seat back in an up-right position, centered on the seat

cushion with their seat belt on, legscomfortably extended and their feeton the floor until the vehicle is parkedand the ignition key is removed.

o The SRS airbag system must deployvery rapidly to provide protection ina crash. If an occupant is out of

position because of not wearing aseat belt, the airbag may forcefullycontact the occupant causing seri-ous or fatal injuries.



59/283

The SRSCM continually monitors all ele-ments while the ignition is "ON" to deter-

mine if a frontal or near-frontal impact issevere enough to require airbag deploy-ment or pre-tensioner seat belt deploy-ment.

The SRS "AIRBAG" warning light on the

instrument panel will illuminate for about6 seconds after the ignition key is turnedto the "ON" position or after the engine isstarted, after which the "AIRBAG" warn-ing light should go out.

B240B01L

Upon deployment, tear seams molded

directly into the pad covers will separateunder pressure from the expansion of theairbags. Further opening of the coversthen allows full inflation of the airbags.

The airbag modules are located both inthe center of the steering wheel and in the

front passenger's panel above the glovebox. When the SRSCM detects a suffi-ciently severe impact to the front of thevehicle, it will automatically deploy thefront airbags.

B240B02L

A fully inflated airbag, in combia properly worn seat belt, slows t

or the passenger's forward mducing the risk of head and ch

After complete inflation, the airbdiately starts deflating, enablingto maintain forward visibility an

ity to steer or operate other co


48


60/283

!

Passenger's Front Airbag

B240B05L

o When installing a container of liquidair freshener inside the vehicle, donot place it near the instrument clus-ter nor on the instrument panel sur-face. If there is any leakage from theair freshener onto these areas (in-strument cluster, instrument panel

or air ventilator), it may damage theseparts. If the liquid from the air fresh-ener does leak onto these areas,wash them with water immediately.

WARNING:o If an airbag deploys, there

loud noise followed by a released in the vehicle. Thditions are normal and areardous - the airbags are p

this fine powder. The dust gduring airbag deployment mskin or eye irritation as wgravate asthma for some Always wash all exposed sthoroughly with lukewarm wa mild soap after an acciden

the airbags were deployedo The SRS can function only

ignition key is in the "ON" pthe SRS "AIRBAG" warndoes not illuminate, or conremains on after illuminabout 6 seconds when thkey is turned to the "ON" poafter the engine is started, cwhile driving, the SRS is noproperly. If this occurs, hvehicle immediately inspyour Hyundai dealer.

Passenger's Front Airbag

CAUTION:o Do not install or place any accesso-

ries (drink holder, cassette holder,sticker, etc.) on the front passenger'spanel above the glove box in a ve-hicle with a passenger's airbag. Suchobjects may become dangerous pro-jectiles and cause injury if thepassenger's airbag inflates.

!

B240B01MC-A


If th f t t iB990A02MC AAT


61/283

!o Before you replace a fuse or discon-nect a battery terminal, turn the igni-tion key to the "LOCK" position andremove the ignition key. Never re-move or replace the airbag related

fuse(s) when the ignition key is in the"ON" position. Failure to heed thiswarning will cause the SRS"AIRBAG" warning light to illuminate.

WARNING:

If the front passenger seat is oca person that the system determ

of adult size, and he/she sit(sitting upright with the seatbupright position, centered oncushion with their seat belt on, fortably extended and their fefloor), the "PASSENGER AIR B

indicator will be turned off andpassenger's airbag will be ableif necessary, in frontal crashesYou will find the "PASSENGEROFF" indicator on the center faThe following table summarizetioning of the system depend

front passenger seat occupan

B990A02MC-AAT

OCCUPANT CLASSIFICATION SYS-

TEM

Your vehicle is equipped with an occu-pant classification system in the frontpassenger's seat. The Occupant Classifi-cation system is designed to detect thepresence of a properly-seated front pas-

senger and determine if the passenger'sfront airbag should be enabled (may in-flate) or not. The driver's front airbag is notaffected or controlled by the OccupantClassification System.

B990A01MC-A


50

This will allow the system toCondition and operation in the front pas


62/283

When an adult is seated in the frontpassenger seat, if the "PASSENGER AIR

BAG OFF" indicator is on, turn the ignitionkey to "LOCK" and ask the passenger tosit prope

hyundai accent 2007

Documents

hyundai vehicleplease

hyundai dealer

hyundai models

new hyundai

hyundaiyour hyundai

specific vehicle

owners manual

maintenance operations