hydraulics of structures
DESCRIPTION
Hydraulics of structuresTRANSCRIPT
![Page 1: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/1.jpg)
Hydraulics of Structures
![Page 2: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/2.jpg)
Structures in this context are simply something placed in the channel to either measure or control flow.
Example: A principle spillway is used as part of a dam design to control the rate at which water is discharged from a reservoir.
Include both inlet and outlet control devices. Control devices can operate as :
Open channel flow in which the flow has a free surface or
Pipe flow in which the flow is in a closed conduit under pressure.
What are structures?
![Page 3: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/3.jpg)
As head on a structure increases, the flow that is discharged through the structure increases.
Figure 5.1 (Haan et al., 1994) shows the head-discharge relationships for several flow control structures.
Most basic principle of hydraulics of structures:
![Page 4: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/4.jpg)
Weirs At its most basic, just an obstruction placed in a
channel that constricts flow as it goes over a crest.
The crest is the edge of the weir over which the water flows.
As the water level (head) over the crest increases, the flow rate increases dramatically.
Two basic types of weirs sharp crested broad crested
![Page 5: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/5.jpg)
Sharp Crested Weirs A sharp crested weir is defined by a thin
crest over which the water springs free as it leaves the upstream face of the weir. Flow over a weir is also called the nappe.
Sharp crested weirs are generally constructed of sheet metal or similar thin material.
![Page 6: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/6.jpg)
Sharp Crested Weir
H
nappe
![Page 7: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/7.jpg)
Sharp Crested Weirs Can have several shapes
Triangular (or v-notch) Rectangular Trapezoidal
Classified by the shape of its notch. V-notch weirs have greater control under low flow
conditions. Rectangular weirs have larger capacity but are less
sensitive for flow measurement.
![Page 8: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/8.jpg)
Sharp Crested Weirs-Generalg
v
2
2
1
Using Bernoulli’s equation
)hzH(g2
v)zH(
g2
v 22
21 −++=++
H hdh
z
g
v
2
2
2
![Page 9: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/9.jpg)
Making the assumption that the velocity head at the upstream point will be much smaller than the velocity head as the flow goes over the weir we assume v1
2/2g is negligible and:
gh2v2 =
H
Crest
dh
L
LdhvdQ 2=
or
Ldhgh2dQ =h
![Page 10: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/10.jpg)
Integrating this from h = 0 to h = H gives
23
0
21
23
22 HgLhgLQ
Hh
h
== ∫=
=
Multiplying by a loss term to compensate for the deviation from ideal flow we get:
23
d Hg2L3
2CQ =
![Page 11: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/11.jpg)
Rectangular WeirsA rectangular weir that spans the full width of the channel is known as a suppressed weir.
23
CLHQ =
H
L
H
Coefficient of Discharge
![Page 12: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/12.jpg)
Hydraulic head (H) for weirs is simply the height of the water surface above the weir crest, measured at a point upstream so that the influence of the velocity head can be ignored.
L is the length of the weir. The coefficient of discharge (C) is dependent
upon units and of the weir shape. For a suppressed weir with H/h < 0.4 (where h is the
height of the weir) C= 3.33 can be used. For 0.4 < H/h < 10, C = 3.27 + 0.4 H/h
![Page 13: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/13.jpg)
A rectangular weir that does not span the whole channel is called a weir with end contractions . The effective length of the weir will be less than the actual weir length due to contraction of the flow jet caused by the sidewalls.
L’
NH1.0'LL −=
Where N is the number of contractions and L’ is the measured length of the crest.
![Page 14: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/14.jpg)
Triangular (v-notch ) weirs Used to measure flow in low flow
conditions.
Θ H
5.2H2
tanKQθ=
![Page 15: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/15.jpg)
For Θ = 90°, K = 2.5 (typically), tan (Θ/2) = 1 therefore,
25
H5.2Q =
For other angles
g215
8CK d=
Where Cd is based on the angle, Θ, and head, H.
![Page 16: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/16.jpg)
Note: Your handout with Figure 12.28 presents the equation for a v-notch weir as:
25
KHQ =
with
2tang2
15
8CK d
θ=
![Page 17: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/17.jpg)
Broad Crested Weirs
W
H
5.109.3 LHQ =
Where L is the width of the weir.
![Page 18: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/18.jpg)
Broad Crested Weirs Broad crested weirs support the flow in the
longitudinal direction (direction of flow). They are used where sharp-crested weirs
may have maintenance problems. The nappe of a broad crested weir does not
spring free.
![Page 19: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/19.jpg)
Roadway Overtopping
( ) 23
rdo HWLCQ =WhereQo – overtopping flowrateCd - overtopping discharge coefficientL – length of roadway crestHWr – upstream depth
Cd = ktCr
Cr – discharge coefficientkt – submergence factorFigure 5.7
![Page 20: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/20.jpg)
Orifices An orifice is simply an opening through
which flow occurs. They can be used to:
Control flow as in a drop inlet Measure the flow through a pipe.
![Page 21: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/21.jpg)
The discharge equation for orifice flow is:
21
)gH2(A'CQ =Where:
C’ is the orifice coefficient (0.6 for sharp edges, 0.98 for rounded edges).
A is the cross-sectional area of the orifice in ft2
g is the gravitational constant
H is the head on the orifice
![Page 22: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/22.jpg)
At low heads, orifices can act as weirs. Calculate the discharge using the suppressed
weir equation where L is equal to the circumference of the pipe.
Calculate the discharge using the orifice equation.
The lower discharge will be the actual discharge.
![Page 23: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/23.jpg)
Pipes as Flow Control Devices
0.6D
D
H’
g2
vKH
2
ee =
g2
vKH
2
bb =
g2
vLKH
2
cc =
g2
v2
H
Energy Grade Line
Elbow and TransitionL
cbe
2
HHHg2
v'H +++=
![Page 24: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/24.jpg)
( )LKKK1g2
v'H cbe
2
+++=
21
cbe
21
)LKKK1(
)'gH2(v
+++=
21
cbe
21
)LKKK1(
)'gH2(aQ
+++=
![Page 25: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/25.jpg)
Head Loss Coefficients Ke is the entrance head loss coefficient and is typically
given a value of 1.0 for circular inlets. Kb is the bend head loss coefficient and is typically
given a value of 0.5 for circular risers connected to round conduits.
For risers with rectangular inlets, the bend head losses and entrance head losses are typically combined to a term Ke’ where values of Ke’ can be found in Table 5.3 and :
21
ce
21
)LK'K1(
)'gH2(aQ
++=
![Page 26: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/26.jpg)
Head Loss Coefficients Kc is the head loss coefficient due to
friction. Values for Kc are given in Tables 5.1 and
5.2 for circular and square pipes. Kc is multiplied by L, the entire length of
the pipe, including the riser.
![Page 27: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/27.jpg)
Frequently, when the drop inlet is the same size as the remainder of the pipe, orifice flow will control and the pipe will never flow full.
If it is desirable to have the pipe flowing full, it may be necessary to increase the size of the drop inlet.
![Page 28: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/28.jpg)
Using Flow Control Structures as Spillways A given drop inlet spillway can have a variety of
discharge relationships, given the head. At the lowest stages the riser acts as a weir. As the level of the reservoir rises, water flowing in from
all sides of the inlet interferes so that the inlet begins to act as an orifice.
As the level continues to rise, the outlet eventually begins to flow full and pipe flow prevails.
A stage-discharge curve is developed by plotting Q vs. H for each of the three relationships. The minimum flow for a given head is the actual discharge used.
![Page 29: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/29.jpg)
have
h1
dh
h2
dl
ROCKFILLHYDRAULIC PROFILE
Rockfill Outlets as Controls
![Page 30: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/30.jpg)
Rockfill Outlets Advantages
Abundant Generally available Usually inexpensive Relative permanence
![Page 31: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/31.jpg)
Rockfill Outlets Major expenses
Grading Transporting Placing stone
![Page 32: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/32.jpg)
Rockfill Outlets Used for
Protective channel linings and breakwaters Add stability to dams Provide energy dissipation zones for reservoir
outlets Flow control structure
![Page 33: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/33.jpg)
Modified Darcy-Weisbach Equation
g
V
df
dl
dhk
2
21
ξ=
![Page 34: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/34.jpg)
Rockfill as Control Structure Model
( )νξ
σ VdRe
−=
Reynolds Number Equation
Friction factor
dl
dh
V
gdfk 2
2ξ=
![Page 35: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/35.jpg)
Friction Factor-Reynolds Number Relationship
83.31600 +=e
k Rf
![Page 36: Hydraulics of structures](https://reader031.vdocuments.mx/reader031/viewer/2022020105/559b15041a28ab9b308b45c1/html5/thumbnails/36.jpg)
h2 – have Relationships
dhhh += 21
221 hh
have+=