hp proliant ml110 generation 5 server installation...

Configuring the server 1. Connect all peripheral to your ProLiant server.

o Keyboardo Mouseo Monitor

2. Determine the server BIOS version.

a. Power up the server.b. Press the Esc key at the HP logo screen, and then press the Pause key to halt

screen movement.c. Note the server BIOS version.d. Verify the server BIOS version against the latest BIOS version listed for this

server on the HP website: http://www.hp.com

e. If you do not have the latest BIOS, update the BIOS now. Refer to the HP ProLiant ML110 Generation 5 Server Maintenance and Service Guide available on the HP website: http://www.hp.com

Default boot priorityBy default, the server searches for boot devices in the following order:

1. Optical disc drive (CD-ROM/DVD-ROM)

2. Removable drive

3. Hard disk drive

4. Embedded NIC

Server configuration guidelinesRead the following items before performing any of the installation procedures described in later sections.

WARNING:Failure to properly turn off the system power before you open the server or before you start removing or installing hardware components may cause serious damage as well as bodily harm.

WARNING:To reduce the risk of personal injury from hot surfaces, allow the chassis and any installed hardware component to cool before touching them.

CAUTION:Observe the ESD precautions, pre- and post-installation procedures, and proper cabling management described in Chapter 2 of the HP ProLiant ML110 Generation 5 Server Maintenance and Service Guide when performing any installation procedure.

Identifying server componentsFront panel components

Item Component Item Component1 Optical disc drive (ODD) 5 Front USB 2.0 ports2 ODD manual eject hole 6 Hard disk drive (HDD) EMI shield3 ODD eject button 7 HDD EMI shield screw4 Power button 8 2nd removable media drive bay EMI shieldNOTE: The location of items 1 and 2 may vary depending on the model of the installed removable media drive.

HP ProLiant ML110 Generation 5 Server Installation Sheet

First edition (July 2007) Part number 446743-001

Rear panel components

Item Component Item Component1 Kensington lock notch 10 Lights Out 100c management port (with option installed)2 Access panel thumbscrew 11 Embedded NIC port (RJ-45)3 Cable lock provision notch 12 Rear USB 2.0 ports4 PCI slot cover retainer 13 Serial port5 PCI slot cover retainer 14 Video port thumbscrew6 PCI1 slot cover 15 PS/2 keyboard port7 PCI2 slot cover 16 PS/2 mouse port 8 PCI3 slot cover 17 Power supply cable socket9 PCI4 slot cover

System board components

Item Code Component1 DIMM 4B Channel B 2nd DIMM slot2 DIMM 3B Channel B 1st DIMM slot3 DIMM 2A Channel A 2nd DIMM slot4 DIMM 1A Channel A 1st DIMM slot5 JP5 Heat sink fan (HSF) cable connector6 CN11 HDD LED connector7 SATA6 2nd removable media drive SATA cable connector8 SATA5 1st removable media drive SATA cable connector 9 SATA4 4th HDD SATA cable connector10 SATA3 3rd HDD SATA cable connector11 SATA2 2nd HDD SATA cable connector12 SATA1 1st HDD SATA cable connector 13 FPCN1 Front panel board connector14 FPUSBCONN1 Front panel USB port connector15 USBCONN3 Internal USB connector for STD USB16 USBCONN2 Internal USB connector for tape device17 BAT1 System battery18 PCI1 32-bit/33 MHz 3.3 V PCI slot19 PCI2 PCI Express x1 link with x8 slot

20 PCI3 PCI Express x1 link with x8 slot21 PCI4 PCI Express x8 link with x8 slot22 CN5 Lights Out 100c upgrade slot23 JP4 System fan connector24 CPU1 Processor 125 PWRCN1 4-pin ATX processor power connector26 ATXPWRCN1 24-pin ATX system board power connector

Opening the serverAccess panel removal

Front bezel removal

Installing a memory moduleThe system has four DIMM slots that support up to 8 GB maximum system memory (2 GB in each of the four DIMM slots).

Observe the following important guidelines when installing memory modules:• Use only HP supported 533/667/800 MHz unbuffered ECC DDR II DIMM in

512 MB, 1 GB, or 2 GB capacities.• Supported DIMM configurations include:

o Single DIMM (non-interleaving) – It must be installed in the DIMM 1A slot.o Two DIMMs (interleaving) – For optimum memory performance, populate

DIMM slots 1A and 3B.o Four DIMMs

ImportantSafetyInformation

Les "Viktig sikkerhetsinformasjon" på dokumentasjons-CDen før du installerer dette produktet.

Læs dokumentet Vigtige sikkerhedsoplysninger på dokumentations-cd'en, før produktet installeres.

Prima dell'installazione, leggere sul CD le Informazioni importanti sulla sicurezza.

Tärkeisiin turvatietoihin" Documentation CD -levyllä ennen tuotteen asentamista.Läs dokumentet Viktig säkerhetsinformation på dokumentations-cd:n innan du installerar denna produkt.

Configuring the server 1. Connect all peripheral to your ProLiant server.

o Keyboardo Mouseo Monitor

2. Determine the server BIOS version.

a. Power up the server.b. Press the Esc key at the HP logo screen, and then press the Pause key to halt

screen movement.c. Note the server BIOS version.d. Verify the server BIOS version against the latest BIOS version listed for this

server on the HP website: http://www.hp.com

e. If you do not have the latest BIOS, update the BIOS now. Refer to the HP ProLiant ML110 Generation 5 Server Maintenance and Service Guide available on the HP website: http://www.hp.com

Default boot priorityBy default, the server searches for boot devices in the following order:

1. Optical disc drive (CD-ROM/DVD-ROM)

2. Removable drive

3. Hard disk drive

4. Embedded NIC

Server configuration guidelinesRead the following items before performing any of the installation procedures described in later sections.

WARNING:Failure to properly turn off the system power before you open the server or before you start removing or installing hardware components may cause serious damage as well as bodily harm.

WARNING:To reduce the risk of personal injury from hot surfaces, allow the chassis and any installed hardware component to cool before touching them.

CAUTION:Observe the ESD precautions, pre- and post-installation procedures, and proper cabling management described in Chapter 2 of the HP ProLiant ML110 Generation 5 Server Maintenance and Service Guide when performing any installation procedure.

Identifying server componentsFront panel components

Item Component Item Component1 Optical disc drive (ODD) 5 Front USB 2.0 ports2 ODD manual eject hole 6 Hard disk drive (HDD) EMI shield3 ODD eject button 7 HDD EMI shield screw4 Power button 8 2nd removable media drive bay EMI shieldNOTE: The location of items 1 and 2 may vary depending on the model of the installed removable media drive.

HP ProLiant ML110 Generation 5 Server Installation Sheet

First edition (July 2007) Part number 446743-001

Rear panel components

Item Component Item Component1 Kensington lock notch 10 Lights Out 100c management port (with option installed)2 Access panel thumbscrew 11 Embedded NIC port (RJ-45)3 Cable lock provision notch 12 Rear USB 2.0 ports4 PCI slot cover retainer 13 Serial port5 PCI slot cover retainer 14 Video port thumbscrew6 PCI1 slot cover 15 PS/2 keyboard port7 PCI2 slot cover 16 PS/2 mouse port 8 PCI3 slot cover 17 Power supply cable socket9 PCI4 slot cover

System board components

Item Code Component1 DIMM 4B Channel B 2nd DIMM slot2 DIMM 3B Channel B 1st DIMM slot3 DIMM 2A Channel A 2nd DIMM slot4 DIMM 1A Channel A 1st DIMM slot5 JP5 Heat sink fan (HSF) cable connector6 CN11 HDD LED connector7 SATA6 2nd removable media drive SATA cable connector8 SATA5 1st removable media drive SATA cable connector 9 SATA4 4th HDD SATA cable connector10 SATA3 3rd HDD SATA cable connector11 SATA2 2nd HDD SATA cable connector12 SATA1 1st HDD SATA cable connector 13 FPCN1 Front panel board connector14 FPUSBCONN1 Front panel USB port connector15 USBCONN3 Internal USB connector for STD USB16 USBCONN2 Internal USB connector for tape device17 BAT1 System battery18 PCI1 32-bit/33 MHz 3.3 V PCI slot19 PCI2 PCI Express x1 link with x8 slot

20 PCI3 PCI Express x1 link with x8 slot21 PCI4 PCI Express x8 link with x8 slot22 CN5 Lights Out 100c upgrade slot23 JP4 System fan connector24 CPU1 Processor 125 PWRCN1 4-pin ATX processor power connector26 ATXPWRCN1 24-pin ATX system board power connector

Opening the serverAccess panel removal

Front bezel removal

Installing a memory moduleThe system has four DIMM slots that support up to 8 GB maximum system memory (2 GB in each of the four DIMM slots).

Observe the following important guidelines when installing memory modules:• Use only HP supported 533/667/800 MHz unbuffered ECC DDR II DIMM in

512 MB, 1 GB, or 2 GB capacities.• Supported DIMM configurations include:

o Single DIMM (non-interleaving) – It must be installed in the DIMM 1A slot.o Two DIMMs (interleaving) – For optimum memory performance, populate

DIMM slots 1A and 3B.o Four DIMMs

ImportantSafetyInformation

Les "Viktig sikkerhetsinformasjon" på dokumentasjons-CDen før du installerer dette produktet.

Læs dokumentet Vigtige sikkerhedsoplysninger på dokumentations-cd'en, før produktet installeres.

Prima dell'installazione, leggere sul CD le Informazioni importanti sulla sicurezza.

Tärkeisiin turvatietoihin" Documentation CD -levyllä ennen tuotteen asentamista.Läs dokumentet Viktig säkerhetsinformation på dokumentations-cd:n innan du installerar denna produkt.

Memory module installation

Installing an expansion board The ProLiant server supports four expansion slots with three separate bus channels (from top to bottom):• PCI Express x8 link with x8 slot (PCI4)• PCI Express x1 link with x8 slots (PCI2 and PCI3)• 32-bit/33 MHz 3.3 V PCI slot (PCI1)

Expansion board installation1. Remove the PCI slot cover retainer and the slot cover opposite the PCI slot

compatible with your expansion board.

2. Install the expansion board.

Installing a hard driveThe server supports a maximum of six internal drives. The two upper drive bays are primarily for removable media drives, while the four lower drive bays are only for hard drives.

Item Component Item Component1 1st removable media drive 5 2nd SAS/SATA hard drive2 2nd removable media drive 6 1st SAS/SATA hard drive3 4th SAS/SATA hard drive 7 Removable media drive spare screws4 3rd SAS/SATA hard drive 8 HDD spare screws

IMPORTANT:SAS hard drives require that you also install a SAS controller board. This board should be installed in the PCI3 slot.

System drives cablingThe figures in this section illustrate the system drives’ data and power cable connections. Observe the proper cabling guidelines described in Chapter 2 of the HP ProLiant ML110 Generation 5 Server Maintenance and Service Guide when routing the cables.

Datacableconnections

SATA model

SAS model

Item Cable HPpartnumberA SATA cables 448180-001B SAS HDD cables 451375-001C SAS HDD LED cable 438884-001

Powercableconnections

Item PSUcablelabel ConnecttoA P5 1st removable driveB P4 2nd removable driveC P6 4th hard driveD P6 3rd hard driveE P10 2nd hard driveF P9 1st hard driveG P1 ATXPWRCN1 (24-pin power connector)H P3 PWRCN1 (4-pin power connector)

Hard drive installation1. Remove the HDD EMI shield.

2. Install the new hard drive. SATA hard drive installation

SAS hard drive installation

Getting additional documentationRefer to the HP ProLiant ML110 Generation 5 Server Support CD for additional information and updates not provided in this installation sheet. You can also access additional information and documentation from the HP website at http://www.hp.com/,either by connecting directly or through the Support CD.

The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.

Intel and Intel Core are trademarks or registred trademarks of Intel Corporation or its subsidiaries in the United States and other countries.

Memory module installation

Installing an expansion board The ProLiant server supports four expansion slots with three separate bus channels (from top to bottom):• PCI Express x8 link with x8 slot (PCI4)• PCI Express x1 link with x8 slots (PCI2 and PCI3)• 32-bit/33 MHz 3.3 V PCI slot (PCI1)

Expansion board installation1. Remove the PCI slot cover retainer and the slot cover opposite the PCI slot

compatible with your expansion board.

2. Install the expansion board.

Installing a hard driveThe server supports a maximum of six internal drives. The two upper drive bays are primarily for removable media drives, while the four lower drive bays are only for hard drives.

Item Component Item Component1 1st removable media drive 5 2nd SAS/SATA hard drive2 2nd removable media drive 6 1st SAS/SATA hard drive3 4th SAS/SATA hard drive 7 Removable media drive spare screws4 3rd SAS/SATA hard drive 8 HDD spare screws

IMPORTANT:SAS hard drives require that you also install a SAS controller board. This board should be installed in the PCI3 slot.

System drives cablingThe figures in this section illustrate the system drives’ data and power cable connections. Observe the proper cabling guidelines described in Chapter 2 of the HP ProLiant ML110 Generation 5 Server Maintenance and Service Guide when routing the cables.

Datacableconnections

SATA model

SAS model

Item Cable HPpartnumberA SATA cables 448180-001B SAS HDD cables 451375-001C SAS HDD LED cable 438884-001

Powercableconnections

Item PSUcablelabel ConnecttoA P5 1st removable driveB P4 2nd removable driveC P6 4th hard driveD P6 3rd hard driveE P10 2nd hard driveF P9 1st hard driveG P1 ATXPWRCN1 (24-pin power connector)H P3 PWRCN1 (4-pin power connector)

Hard drive installation1. Remove the HDD EMI shield.

2. Install the new hard drive. SATA hard drive installation

SAS hard drive installation

Getting additional documentationRefer to the HP ProLiant ML110 Generation 5 Server Support CD for additional information and updates not provided in this installation sheet. You can also access additional information and documentation from the HP website at http://www.hp.com/,either by connecting directly or through the Support CD.

The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.

Intel and Intel Core are trademarks or registred trademarks of Intel Corporation or its subsidiaries in the United States and other countries.

hp proliant ml110 generation 5 server installation...

Documents