hp 6200 yl switch series - andover consulting group · 2015-11-30 · quickspecs hp 6200 yl switch...

QuickSpecs HP 6200 yl Switch Series

Overview

c04123297 — DA – 12437 Worldwide — Version 21 — July 24, 2015

HP 6200 yl Switch Series (Retired)

Models HP 6200-24G-mGBIC yl Switch J8992A

Introduction The HP 6200-24G-mGBIC yl Switch is an advanced Layer 3 stackable switch in 1U height. It has 24 mini-GBIC slots and an expansion slot for an optional 4-port 10GbE module.

Designed to be deployed as an aggregator of traffic from the edge to the core of the network, this switch supports a variety of Gigabit mini-GBICs, such as SX, LX, LH, and 1000BASE-T. The foundation for this switch is a purpose-built ProVision ASIC that allows the most demanding networking features, such as quality of service (QoS) and security, to be implemented in a scalable yet granular fashion. With its high-performance architecture, 10GbE capability, and programmable ASIC, this switch offers excellent investment protection, flexibility, and scalability.

Key features Distribution layer Layer 2 to 4 and intelligent edge feature set High performance Low-cost mini-GBIC connectivity 10GbE uplinks

Features and Benefits Software-defined networking

NEW OpenFlow supports OpenFlow 1.0 and 1.3 specifications to enable SDN by allowing separation of the data (packet forwarding) and control (routing decision) paths

Quality of Service (QoS)

Advanced classifier-based QoS classifies traffic using multiple match criteria based on Layer 2, 3, and 4 information; applies QoS policies such as setting priority level and rate limit to selected traffic on a per-port or per-VLAN basis

Layer 4 prioritization enables prioritization based on TCP/UDP port numbers

Traffic prioritization allows real-time traffic classification into eight priority levels mapped to eight queues

Bandwidth shaping: o Port-based rate limiting

provides per-port ingress/egress enforced maximum bandwidth o Classifier-based rate limiting

uses access control list (ACL) to enforce maximum bandwidth for ingress traffic on each port o Reduced bandwidth

provides per-port, per-queue egress-based reduced bandwidth Class of Service (CoS)


Overview


sets the IEEE 802.1p priority tag based on IP address, IP Type of Service (ToS), Layer 3 protocol, TCP/UDP port number, source port, and DiffServ

Management

Remote intelligent mirroring mirrors selected ingress/egress traffic based on ACL, port, MAC address, or VLAN to a local or remote HP 8200 zl, 6600, 6200 yl, 5400 zl, or 3500 Switch located anywhere on the network

RMON, XRMON, and sFlow provide advanced monitoring and reporting capabilities for statistics, history, alarms, and events

IEEE 802.1AB Link Layer Discovery Protocol (LLDP) advertises and receives management information from adjacent devices on a network, facilitating easy mapping by network management applications

Command authorization leverages RADIUS to link a custom list of CLI commands to an individual network administrator's login; an audit trail documents activity

Friendly port names allow assignment of descriptive names to ports

Dual flash images provide independent primary and secondary operating system files for backup while upgrading

Multiple configuration files can be stored to the flash image

Uni-Directional Link Detection (UDLD) monitors a cable between two switches and shuts down the ports on both ends if the cable is broken, turning the bidirectional link into a unidirectional one; this prevents network problems such as loops

Management simplicity provides common software features and CLI implementation across all ProVision-based switches (including the zl and yl switches)

Comware-compatible CLI: o Comware-compatible CLI

bridges the experience of HP Comware CLI users who are using the HP ProVision software CLI o Display and fundamental Comware CLI commands

are embedded in the switch CLI as native commands; display output is formatted as on Comware-based switches, and fundamental commands provide a Comware-familiar initial switch setup

o Configuration Comware CLI commands when Comware commands are entered, CLI help is elicited to formulate the correct ProVision software CLI command

Connectivity

Jumbo frames on Gigabit Ethernet and 10-Gigabit Ethernet ports, jumbo frames allow high-performance remote backup and disaster-recovery services

IPv6: o IPv6 host

enables switches to be managed in an IPv6 network o Dual stack (IPv4 and IPv6)

transitions from IPv4 to IPv6, supporting connectivity for both protocols o MLD snooping

forwards IPv6 multicast traffic to the appropriate interface o IPv6 ACL/QoS

supports ACL and QoS for IPv6 network traffic o IPv6 routing

supports static and OSPFv3 routing protocols


Overview


o 6in4 tunneling supports encapsulation of IPv6 traffic in IPv4 packets

Performance

High-speed/capacity architecture 105.6 Gbps crossbar switching fabric provides intramodule and intermodule switching with 75.7 million pps throughput on the purpose-built ProVision ASICs

Selectable queue configurations allows for increased performance by selecting the number of queues and associated memory buffering that best meet the requirements of the network applications

Resiliency and high availability

NEW Virtual Router Redundancy Protocol (VRRP) allows groups of two routers to dynamically back each other up to create highly available routed environments in IPv4 and IPv6 networks

IEEE 802.1s Multiple Spanning Tree Protocol provides high link availability in multiple VLAN environments by allowing multiple spanning trees; encompasses IEEE 802.1D Spanning Tree Protocol and IEEE 802.1w Rapid Spanning Tree Protocol

IEEE 802.3ad Link Aggregation Control Protocol (LACP) and HP port trunking support up to 144 trunks, each with up to eight links (ports) per trunk

Distributed trunking enables loop-free and redundant network topology without using Spanning Tree Protocol; allows a server or switch to connect to two switches using one logical trunk for redundancy and load sharing

Uplink Failure Detection provides active-standby network path redundancy for servers that are configured for active-standby NIC teaming

NEW SmartLink provides easy-to-configure link redundancy of active and standby links

Layer 2 switching

IEEE 802.1ad Q-in-Q increases the scalability of an Ethernet network by providing a hierarchical structure; connects multiple LANs on a high-speed campus or metro network

HP switch meshing dynamically load balances across multiple active redundant links to increase available aggregate bandwidth

VLAN support and tagging supports complete IEEE 802.1Q standard and 2,048 VLANs simultaneously

IEEE 802.1v protocol VLANs isolate select non-IPv4 protocols automatically into their own VLANs

GARP VLAN Registration Protocol allows automatic learning and dynamic assignment of VLANs

Rapid Per-VLAN Spanning Tree (RPVST+) allows each VLAN to build a separate spanning tree to improve link bandwidth usage; is compatible with PVST+

Layer 3 services

User Datagram Protocol (UDP) helper function allows UDP broadcasts to be directed across router interfaces to specific IP unicast or subnet broadcast addresses and prevents server spoofing for UDP services such as DHCP

Loopback interface address defines an address in Routing Information Protocol (RIP) and Open Standard Path First (OSPF), improving diagnostic


Overview


capability Route map

provide more control during route redistribution; allow filtering and altering of route metrics

Layer 3 routing

Static IP routing provides manually configured routing for both IPv4 and IPv6 networks

Routing Information Protocol (RIP) provides RIPv1 and RIPv2 routing

OSPF provides OSPFv2 for IPv4 routing and OSPFv3 for IPv6 routing

Border Gateway Protocol (BGP) provides IPv4 Border Gateway Protocol routing, which is scalable, robust, and flexible

Security

Switch CPU protection provides automatic protection against malicious network traffic trying to shut down the switch

Virus throttling detects traffic patterns typical of WORM-type viruses and either throttles or entirely prevents the virus from spreading across the routed VLANs without requiring external appliances

ICMP throttling defeats ICMP denial-of-service attacks by enabling any switch port to automatically throttle ICMP traffic

Multiple user authentication methods: o IEEE 802.1X users per port: provides authentication of multiple IEEE 802.1X users per port; prevents user

"piggybacking" on another user's IEEE 802.1X authentication o Web-based authentication: authenticates from Web browser for clients that do not support IEEE 802.1X

supplicant; customized remediation can be processed on an external Web server o MAC-based authentication: client is authenticated with the RADIUS server based on client's MAC address o Concurrent IEEE 802.1X, Web, and MAC authentication schemes per port: switch port will accept up to 32

sessions of IEEE 802.1X, Web, and MAC authentications Access control lists (ACLs)

provide filtering based on the IP field, source/destination IP address/subnet, and source/destination TCP/UDP port number on a per-VLAN or per-port basis

Identity-driven ACL enables implementation of a highly granular and flexible access security policy and VLAN assignment specific to each authenticated network user

DHCP protection blocks DHCP packets from unauthorized DHCP servers, preventing denial-of-service attacks

STP BPDU port protection blocks Bridge Protocol Data Units (BPDUs) on ports that do not require BPDUs, preventing forged BPDU attacks

Dynamic IP lockdown works with DHCP protection to block traffic from unauthorized hosts, preventing IP source address spoofing

Dynamic ARP protection blocks ARP broadcasts from unauthorized hosts, preventing eavesdropping or theft of network data

Detection of malicious attacks monitors 10 types of network traffic and sends a warning when an anomaly that potentially can be caused by malicious attacks is detected

Port security allows access only to specified MAC addresses, which can be learned or specified by the administrator

MAC address lockout prevents particular configured MAC addresses from connecting to the network

Source-port filtering


Overview


allows only specified ports to communicate with each other RADIUS/TACACS+

eases switch management security administration by using a password authentication server Secure Shell

encrypts all transmitted data for secure remote CLI access over IP networks Secure Sockets Layer (SSL)

encrypts all HTTP traffic, allowing secure access to the browser-based management GUI in the switch Secure FTP

allows secure file transfer to and from the switch; protects against unwanted file downloads or unauthorized copying of a switch configuration file

Management Interface Wizard helps secure management interfaces such as SNMP, telnet, SSH, SSL, Web, and USB at the desired level

Secure management access securely encrypts all access methods (CLI, GUI, or MIB) through SSHv2, SSL, and/or SNMPv3

Switch management logon security can require either RADIUS or TACACS+ authentication for secure switch CLI logon

Security banner: displays customized security policy when users log in to the switch USB Secure Autorun (requires HP PCM+)

deploys, diagnoses, and updates a switch using a USB flash drive; works with a secure credential to prevent tampering STP Root Guard

protects the root bridge from malicious attacks or configuration mistakes

Convergence

IP multicast routing includes PIM Sparse and Dense modes to route IP multicast traffic

IP multicast snooping (data-driven IGMP) automatically prevents flooding of IP multicast traffic

LLDP-MED (Media Endpoint Discovery) is a standard extension of LLDP that stores values for parameters such as QoS and VLAN to automatically configure network devices such as IP phones

Auto VLAN configuration for voice: o RADIUS VLAN: uses a standard RADIUS attribute and LLDP-MED to automatically configure a VLAN for IP phones o CDPv2: uses CDPv2 to configure legacy IP phones

NEW Local MAC Authentication assigns attributes such as VLAN and QoS using locally configured profile that can be a list of MAC prefixes

Warranty and support

Lifetime Warranty 2.0 advance hardware replacement for as long as you own the product with next-business-day delivery (available in most countries)†

Electronic and telephone support (for Lifetime Warranty 2.0) limited 24x7 telephone support is available from HP for the first 3 years; limited electronic and business hours telephone support is available from HP for the entire warranty period; to reach our support centers, refer to http://www.hp.com/networking/contact-support; for details on the duration of support provided with your product purchase, refer to www.hp.com/networking/warrantysummary

Software releases to find software for your product, refer to http://www.hp.com/networking/support; for details on the software releases available with your product purchase, refer to www.hp.com/networking/warrantysummary

†HP warranty includes repair or replacement of hardware for as long as you own the product, with next business day advance replacement (available in most countries). The disk drive included with HP AllianceOne Advanced Services and Services zl Modules, HP Threat Management Services zl Module, HP AllianceOne Extended zl Module with Riverbed Steelhead, HP MSM765zl Mobility

http://www.hp.com/networking/warrantysummary

http://www.hp.com/networking/warrantysummary


Overview


Controller and HP Survivable Branch Communication zl Module powered by Microsoft Lync has a five-year hardware warranty. For details, refer to the Software license and hardware warranty statements at http://www.hp.com/networking/warranty.


Configuration


Build To Order: BTO is a standalone unit with no integration. BTO products ship standalone are not part of a CTO or Rack-Shippable solution.

HP 6200-24G-mGBIC yl Switch J8992A

24 open mini-GBIC (SFP) slots min=0 \ max=24 SFP Transceivers 1U - Height

See Configuration Note:1, 2

PDU Cable NA/MEX/TW/JP J8992A#B2B

C15 PDU Jumper Cord (NA/MEX/TW/JP)

PDU Cable ROW J8992A#B2C

C15 PDU Jumper Cord (ROW)

Configuration Rules:

Note 1 The following Transceivers install into this switch:

HP X121 1G SFP LC SX Transceiver J4858C

HP X121 1G SFP LC LX Transceiver J4859C

HP X111 100M SFP LC FX Transceiver J9054C

HP X121 1G SFP RJ45 T Transceiver J8177C

HP X112 100M SFP LC BX-D Transceiver J9099B

HP X112 100M SFP LC BX-U Transceiver J9100B

HP X121 1G SFP LC LH Transceiver J4860C

HP X122 1G SFP LC BX-D Transceiver J9142B

HP X122 1G SFP LC BX-U Transceiver J9143A

HP X131 10G X2 SC ER Transceiver J8438A

HP X131 10G X2 SC SR Transceiver J8436A

HP X131 10G X2 SC LR Transceiver J8437A

HP X131 10G X2 SC LRM Transceiver J9144A

Note 2 Localization required on orders without #B2B or #B2C options.

Remarks:

Drop down under power supply should offer the following options and results: Switch/Router/Power Supply to PDU Power Cord - #B2B in North America, Mexico, Taiwan, and Japan or #B2C ROW. (Watson Default B2B or B2C for Rack Level CTO) Switch/Router/Power Supply to Wall Power Cord - Localized Option (Watson Default for BTO and Box Level CTO)

Factory Racked Models

HP 6200-24G-mGBIC yl Switch J8992A

24 open mini-GBIC (SFP) slots min=0 \ max=24 SFP Transceivers



Configuration


1U - Height
















Note 2 If this switch is factory installed in HP Universal Racks, Then the J9583A#0D1 is required. AMS then J9583A#0D1is required. EMEA then J9583A#0D1 is required. APD, Japan and China then J9583A#0D1 is required. CLIC Only - Allow the J9583AZ in all regions.

Enter the following menu selections as integrated to the CTO Model X server above if order is factory built.

Modules

System (std 0 // max=2) User Selection (min 0 / max=2) per Chassis

HP 10GbE 2-port SFP+/2-port CX4 yl Mod J9312A

min=0 \ max=2 SFP Transceivers See Configuration Note:1

HP 10GbE 2-port X2 / 2-port CX4 yl Module J8694A












Configuration







Transceivers

SFP Transceivers







HP X122 1G SFP LC BX-U Transceiver J9143B







Cables

Multi-Mode Cables

HP .5m Multi-mode OM3 LC/LC FC Cable AJ833A

HP 1m Multi-mode OM3 LC/LC FC Cable AJ834A

HP 2 m Multimode OM3 LC/LC FC Cable AJ835A





HP Premier Flex LC/LC OM4 2f 1m Cbl QK732A






Switch Options

Rack Mount kits

HP X410 1U Univ 4-post Rack Mnt Kit J9583A



Configuration


Rack Shelf AB469A

See Configuration Note:3


Note 1 Default with switch.

Note 2 If this Mounting Kit is order with #0D1 then it integrates to the HP Universal Rack. (not the switch)

Note 3 This has existing rules that say 1 per 20 if 1U and 1 per 10 if its 3U or more. This rule is fine for ProCurve. Note: Both parts above are required to ship the 62xx Series Switches installed in a rack. Exceptions- The Shelf Kit (AB469A) may be removed if the Switch is supported underneath by a full depth Server of 3U height or greater mounted on fixed rails


Technical Specifications


HP 6200-24G-mGBIC yl Switch (J8992A)

I/O ports and slots 24 open mini-GBIC (SFP) slots Supports a maximum of 4 10-GbE ports, with optional module

Physical characteristics Dimensions 17.44(w) x 15.43(d) x 1.73(h) in (44.3 x 39.2 x 4.4 cm) (1U height)

Weight 14.11 lb (6.4 kg)

Memory and processor Processor Freescale PowerPC 8540 @ 666 MHz, 4 MB flash, 256 MB DDR SDRAM

Mounting and enclosure Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included); horizontal surface mounting only

Performance 1000 Mb Latency < 3.7 µs (FIFO 64-byte packets)

10 Gbps Latency < 2.1 µs (FIFO 64-byte packets)

Throughput up to 75.7 million pps

Routing/Switching capacity

101.8 Gb/s

Switch fabric speed 105.6 Gb/s

Routing table size 10000 entries (IPv4)

Environment Operating temperature 32ºF to 131ºF (0ºC to 55ºC); 32°F to 104°F (40°C) when used with any X2 10-GbE

Operating relative humidity

15% to 95% @ 104ºF (40ºC), noncondensing

Non-operating/ Storage temperature

–40°F to 158°F (-40°C to 70°C)

Non-operating/ Storage relative humidity

15% to 95% at 149°F (65°C), noncondensing

Altitude up to 15,000 ft (4.6 km)

Acoustic Power: 55.1 dB; DIN 45635T.19 per ISO 7779

Electrical characteristics Description The switch automatically adjusts to any voltage between 100-127 and 200-240 V with either 50 or 60 Hz.

Maximum heat dissipation

829 BTU/hr (875 kJ/hr)

AC v oltage 100-127/200-240 VAC

Current 1.8/0.9 A

Power consumption 243 W

Frequency 50/60 Hz

Safety CSA 22.2 No. 60950; UL 60950; IEC 60950; EN 60950

Emissions FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A

Immunity EN EN 55024, CISPR 24

ESD IEC 61000-4-2; 4 kV CD, 8 kV AD

Radiated IEC 61000-4-3; 3 V/m

EFT/Burst IEC 61000-4-4; 1.0 kV (power line), 0.5 kV (signal line)

Surge IEC 61000-4-5; 1 kV/2 kV AC

Conducted IEC 61000-4-6; 3 V

Power frequency magnetic field

IEC 61000-4-8; 1 A/m, 50 or 60 Hz




Voltage dips and interruptions

IEC 61000-4-11; >95% reduction, 0.5 period; 30% reduction, 25 periods

Harmonics EN 61000-3-2, IEC 61000-3-2

Flicker EN 61000-3-3, IEC 61000-3-3

Management HP PCM+; HP PCM (included); command-line interface; Web browser; configuration menu; out-of-band management (serial RS-232C)

Notes Supported 1G SFP transceivers are revision "B" or later (product number ends with the letter "B" or later; for example, J9142B, J8177C).

Services 3-year, 4-hour onsite, 13x5 coverage for hardware (U2855E) 3-year, 4-hour onsite, 24x7 coverage for hardware (U2856E) 3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 SW phone support and SW updates (U6304E) 3-year, 24x7 SW phone support, software updates (UE262E) 1-year, post-warranty, 4-hour onsite, 13x5 coverage for hardware (HR889E) 1-year, post-warranty, 4-hour onsite, 24x7 coverage for hardware (HR890E) 1-year, post-warranty, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone support (HR891E) Installation with minimum configuration, system-based pricing (U4826E) Installation with HP-provided configuration, system-based pricing (U4830E) 4-year, 4-hour onsite, 13x5 coverage for hardware (UR868E) 4-year, 4-hour onsite, 24x7 coverage for hardware (UR869E) 4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (UR870E) 4-year, 24x7 SW phone support, software updates (UR871E) 5-year, 4-hour onsite, 13x5 coverage for hardware (UR872E) 5-year, 4-hour onsite, 24x7 coverage for hardware (UR873E) 5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone (UR874E) 5-year, 24x7 SW phone support, software updates (UR875E) 3 Yr 6 hr Call-to-Repair Onsite (UW356E) 4 Yr 6 hr Call-to-Repair Onsite (UW357E) 5 Yr 6 hr Call-to-Repair Onsite (UW358E) 1-year, 6 hour Call-To-Repair Onsite for hardware (HR893E) 1-year, 24x7 software phone support, software updates (HR892E) 1-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange (HS610E) 1-year, 24x7 software phone support, software updates + 4 hour hardware exchange (HS611E) 3-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange (HS612E) 3-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HS613E) 4-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange (HS614E) 4-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HS615E) 5-year, 24x7 software phone support, software updates + Next Business Day Hardware Exchange (HS616E) 5-year, 24x7 software phone support, software updates + 4 hour Hardware Exchange (HS617E)




Refer to the HP website at www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office.

Standards and protocols BGP RFC 1997 BGP Communities Attribute RFC 2918 Route Refresh Capability RFC 4271 A Border Gateway Protocol 4 (BGP-4) RFC 4456 BGP Route Reflection: An Alternative to Full Mesh Internal BGP (IBGP) RFC 5492 Capabilities Advertisement with BGP-4

Device Management RFC 1591 DNS (client) HTML and telnet management

General Protocols IEEE 802.1ad Q-in-Q IEEE 802.1AX-2008 Link Aggregation IEEE 802.1D MAC Bridges IEEE 802.1p Priority IEEE 802.1Q VLANs IEEE 802.1s Multiple Spanning Trees IEEE 802.1v VLAN classification by Protocol and Port IEEE 802.1w Rapid Reconfiguration of Spanning Tree IEEE 802.3ad Link Aggregation Control Protocol (LACP) IEEE 802.3x Flow Control RFC 768 UDP RFC 783 TFTP Protocol (revision 2) RFC 792 ICMP RFC 793 TCP RFC 826 ARP RFC 854 TELNET RFC 868 Time Protocol RFC 951 BOOTP RFC 1058 RIPv1 RFC 1350 TFTP Protocol (revision 2) RFC 1519 CIDR RFC 1542 BOOTP Extensions RFC 2030 Simple Network Time Protocol (SNTP) v4 RFC 2131 DHCP RFC 2453 RIPv2 RFC 2548 (MS-RAS-Vendor only) RFC 3046 DHCP Relay Agent Information Option RFC 3576 Ext to RADIUS (CoA only) RFC 3768 VRRP RFC 4675 RADIUS VLAN & Priority UDLD (Uni-directional Link Detection)

IP Multicast RFC 3376 IGMPv3 (host joins only) RFC 3973 PIM Dense Mode RFC 4601 PIM Sparse Mode

IPv6 RFC 1981 IPv6 Path MTU Discovery RFC 2375 IPv6 Multicast Address Assignments

http://www.hp.com/networking/services




RFC 2460 IPv6 Specification RFC 2464 Transmission of IPv6 over Ethernet Networks RFC 2710 Multicast Listener Discovery (MLD) for IPv6 RFC 2925 Definitions of Managed Objects for Remote Ping, Traceroute, and Lookup Operations (Ping only) RFC 3019 MLDv1 MIB RFC 3315 DHCPv6 (client and relay) RFC 3484 Default Address Selection for IPv6 RFC 3587 IPv6 Global Unicast Address Format RFC 3596 DNS Extension for IPv6 RFC 3810 MLDv2 for IPv6 RFC 3810 Multicast Listener Discovery Version 2 (MLDv2) for IPv6 RFC 4022 MIB for TCP RFC 4087 IP Tunnel MIB RFC 4113 MIB for UDP RFC 4213 Basic Transition Mechanisms for IPv6 Hosts and Routers RFC 4251 SSHv6 Architecture RFC 4252 SSHv6 Authentication RFC 4253 SSHv6 Transport Layer RFC 4254 SSHv6 Connection RFC 4291 IP Version 6 Addressing Architecture RFC 4293 MIB for IP RFC 4294 IPv6 Node Requirements RFC 4419 Key Exchange for SSH RFC 4443 ICMPv6 RFC 4541 IGMP & MLD Snooping Switch RFC 4861 IPv6 Neighbor Discovery RFC 4862 IPv6 Stateless Address Auto-configuration RFC 5095 Deprecation of Type 0 Routing Headers in IPv6 RFC 5340 OSPF for IPv6 RFC 5453 Reserved IPv6 Interface Identifiers RFC 5519 Multicast Group Membership Discovery MIB (MLDv2 only) RFC 5722 Handling of Overlapping IPv6 Fragments

MIBs IEEE 802.1ap (MSTP and STP MIB's only) RFC 1213 MIB II RFC 1493 Bridge MIB RFC 1724 RIPv2 MIB RFC 1850 OSPFv2 MIB RFC 2021 RMONv2 MIB RFC 2096 IP Forwarding Table MIB RFC 2613 SMON MIB RFC 2618 RADIUS Client MIB RFC 2620 RADIUS Accounting MIB




RFC 2665 Ethernet-Like-MIB RFC 2668 802.3 MAU MIB RFC 2674 802.1p and IEEE 802.1Q Bridge MIB RFC 2737 Entity MIB (Version 2) RFC 2787 VRRP MIB RFC 2863 The Interfaces Group MIB RFC 2925 Ping MIB RFC 2933 IGMP MIB

Network Management IEEE 802.1AB Link Layer Discovery Protocol (LLDP) RFC 2819 Four groups of RMON: 1 (statistics), 2 (history), 3 (alarm) and 9 (events) RFC 3176 sFlow ANSI/TIA-1057 LLDP Media Endpoint Discovery (LLDP-MED) SNMPv1/v2c/v3 XRMON

OSPF RFC 2328 OSPFv2 RFC 3101 OSPF NSSA RFC 5340 OSPF for IPv6

QoS/Cos RFC 2474 DiffServ Precedence, including 8 queues/port RFC 2597 DiffServ Assured Forwarding (AF) RFC 2598 DiffServ Expedited Forwarding (EF)

Security IEEE 802.1X Port Based Network Access Control RFC 1492 TACACS+ RFC 2865 RADIUS (client only) RFC 2866 RADIUS Accounting RFC 3579 RADIUS Support For Extensible Authentication Protocol (EAP) Secure Sockets Layer (SSL) SSHv2 Secure Shell


Accessories


HP 6200 yl Switch Series accessories HP 6200-24G-mGBIC yl Switch (J8992A)

HP 10GbE 2-port SFP+ / 2-port CX4 yl Module J9312A

HP 10GbE 2-port X2 / 2-port CX4 yl Module J8694A



HP X131 10G X2 CX4 Transceiver J8440C











HP X122 1G SFP LC BX-U Transceiver J9143B

HP LC to LC Multi-mode OM3 2-Fiber 0.5m 1-Pack Fiber Optic Cable AJ833A

HP Premier Flex LC/LC Multi-mode OM4 2 fiber 1m Cable QK732A






HP 620 Redundant/External Power Supply J8696A


Accessory Product Details


HP 10GbE 2-port X2/2-port CX4 yl Module (J8694A)

Ports 2 open 10-GbE X2 transceiver slots 2 10-GbE ports (IEEE 802.3ak Type 10GBASE-CX4); Duplex: full only

Physical characteristics Dimensions 7.76(d) x 7.52(w) x 14.29(h) in. (19.7 x 19.1 x 36.3 cm)

Weight 1.54 lb. (0.7 kg)

Environment Operating temperature 32°F to 131°F (0°C to 55°C)


15% to 95%, noncondensing

Nonoperating/Storage temperature

-40°F to 158°F (-40°C to 70°C)

Nonoperating/Storage relative humidity


Cabling Maximum distance: • CX4: 15 m using CX4 cable or 300 m using media converter with ribbon MMF

Notes Operating temperature is 32°F to 104°F (0°C to 40°C) if any X2 10-GbE optic or transceiver is inserted in any X2 slot. One 0.5 m CX4 cable is included.

Services Refer to the HP website at: http://www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office.

HP 10GbE 2-port SFP+/2-port CX4 yl Module (J9312A)

Ports 2 SFP+ 10-GbE ports (IEEE 802.3ae Type 10GBASE-LR); Duplex: full only 2 CX4 10-GbE ports (IEEE 802.3ak Type 10GBASE-CX4); Duplex: full only







-40°F to 158°F (-40°C to 70°C)



Cabling Maximum distance: • CX4: 15 m using CX4 cable or 300 m using media converter with ribbon MMF

Notes Operating temperature is 32°F to 104°F (0°C to 40°C) if any SFP+ 10-GbE optic or transceiver is inserted in any SFP+ slot. One 0.5 m CX4 cable is included.

Services Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office.

HP 620 Redundant/External Power Supply (J8696A)

Ports 2 redundant power supply ports Restrictions: 195 W available per port





2 external power supply ports Restrictions: 398 W available per port

Physical characteristics Dimensions 15.4(d) x 17.4(w) x 1.73(h) in. (39.12 x 44.2 x 4.39 cm) (1U height)


Mounting Mounts in an EIA-standard 19 in. telco rack or equipment cabinet (hardware included); horizontal surface mounting only



15% to 95% @ 104°F (40°C), noncondensing


-40°F to 158°F (-40°C to 70°C)


15% to 90% @ 149°F (65°C), noncondensing

Altitude up to 10,000 ft. (3 km)

Acoustic LwA per ISO 7779: 54.2 dB

Electrical characteristics Maximum heat dissipation

400 BTU/hr (422 kJ/hr), for the actual 620 itself. PoE-powered device heat dissipation assumed to be outside the 620.

Voltage 100-127/200-240 VAC

Current 16/8 A

Maximum power rating 1440 W

RPS power 390 W

PoE power 796 W

RPS 12 V

PoE -50 V

Frequency 50/60 Hz

Notes Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated. Above figures are for maximum RPS and PoE power being supplied to two switches simultaneously. 200 - 240 V power cords shipped with the 620 have a wall plug rated as close to 13 A as specific country standards allow.

Safety CSA 22.2 No. 60950; EN 60950/IEC 60950; UL 60950

Emissions FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A

Immunity EN EN 55024, CISPR 24

ESD IEC 61000-4-2

Radiated IEC 61000-4-3

EFT/Burst IEC 61000-4-4

Surge IEC 61000-4-5

Conducted IEC 61000-4-6

Power frequency IEC 61000-4-8




magnetic field

Voltage dips and interruptions

IEC 61000-4-11

Harmonics EN 61000-3-2, IEC 61000-3-2

Flicker EN 61000-3-3, IEC 61000-3-3

Management Unmanaged power supply; provides information via LEDs (LEDs repeated on front and back panel) or through port interfaces of attached devices

Notes The 620 supports the HP Switch 2900 Series (RPS) and 3500yl Series (RPS/PoE), as well as 6200yl (RPS) switches. The HP Switch 5400zl Series is not supported. The 620 includes four 2 m RPS/EPS cables. These cables can be used to carry either RPS or PoE power to the switch being powered.

Services 3-year, 4-hour onsite, 13x5 coverage for hardware (U9270E) 3-year, 4-hour onsite, 24x7 coverage for hardware (U9271E) 4-year, 4-hour onsite, 13x5 coverage for hardware (UR854E) 4-year, 4-hour onsite, 24x7 coverage for hardware (UR855E) 5-year, 4-hour onsite, 13x5 coverage for hardware (UR857E) 5-year, 4-hour onsite, 24x7 coverage for hardware (UR858E) 3 Yr 6 hr Call-to-Repair Onsite (UW371E) 4 Yr 6 hr Call-to-Repair Onsite (UW372E) 5 Yr 6 hr Call-to-Repair Onsite (UW373E) Refer to the HP website at: http://www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office.

HP X131 10G X2 SC ER Transceiver (J8438A)

HP X131 10G X2 SC ER Transceiver: An X2 format 10-gigabit transceiver with SC connectors using ER technology.

Ports 1 SC 10-GbE port (IEEE 802.3ae Type 10GBASE-ER); Duplex: full only

Connectivity Connector type SC

Wavelength 1550 nm



Transceiver form factor X2

Environment Operating temperature 32ºF to 104ºF (0ºC to 40ºC)



Electrical characteristics Power consumption typical

3 W

Power consumption maximum

4.5 W

Cabling Cable type:: Low metal content, single-mode fiber-optic, complying with ITU-T G.652 and ISO/IEC 793-2 Type B1;

Cable length 2m to 30km (max 40km on engineered links)

Fiber type Single Mode

Notes Conditioning patch cord cables are not supported For fiber patch cords, use Ultra Physical Contact (UPC) surface termination/polish. Angled Physical Contact (APC) is not recommended.

Services Refer to the HP website at www.hp.com/networking/services for details on





the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office.

HP X131 10G X2 SC SR Transceiver (J8436A)

HP X131 10G X2 SC SR Transceiver: An X2 format 10-gigabit transceiver with SC connectors using SR technology.

Ports 1 SC 10-GbE port (IEEE 802.3ae Type 10GBASE-SR); Duplex: full only


Wavelength 850 nm








-40ºF to 185ºF (-40ºC to 85ºC)





1.7 W


2.4 W

Cabling Cable type:: 62.5/125 µm or 50/125 µm (core/cladding) graded-index, low metal content, multimode fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2 Type A1b or A1a, respectively;

Maximum distance:

2-26m with 62.5 µm multimode cable @ 160 MHz*km 2-33m with 62.5 µm multimode cable @ 200 MHz*km 2-66m with 50 µm multimode cable @ 400 MHz*km 2-82m with 50 µm multimode cable @ 500 MHz*km 2-300m with 50 µm multimode cable @ 2000 MHz*km

Cable length 2-300m

Fiber type Multi Mode

Notes For fiber patch cords, use Ultra Physical Contact (UPC) surface termination/polish. Angled Physical Contact (APC) is not recommended.

Services Refer to the HP website at http://www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office.

HP X131 10G X2 CX4 Transceiver (J8440C)

HP X131 10G X2 CX4

Ports 1 CX4 10-GbE port (IEEE 802.3ak Type 10GBASE-CX4); Duplex: full only

Connectivity Connector type CX4





Transceiver: An X2 format 10-gigabit CX4 transceiver.










1.0 W


3.3 W

Cabling Maximum distance: • 15m with CX4 cables • 300m with optical media converter and multimode fiber cable

Notes Connector: CX4; Duplex: full For suggested vendors of CX4 cables, please see the "Cabling" answers on the "HP 10-GbE Transceivers" FAQs Web page.

Services Refer to the HP website at www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office.

HP X111 100M SFP LC FX Transceiver (J9054C)

Ports 1 LC 100BASE-FX port (IEEE 802.3u Type 100BASE-FX); Duplex: half or full





5% to 95%


-40°F to 185°F (-40°C to 85°C)


5% to 85%


Cabling Cable type: 62.5/125 ìm or 50/125 ìm (core/cladding) diameter, graded-index, low metal content, multimode fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2 Type A1b or A1a, respectively; Maximum distance: • 2 km (full duplex) or 412 m (half duplex)

Notes Transmitter wavelength: 1310nm Power consumption is 1.1 watt maximum. For supported platforms and minimum software requirements to support this product, see the document titled "Support for the J9054C 100-FX SFP-LC Transceiver" on the "ProCurve Mini-GBICs and SFPs" Manuals Web page.






HP X131 10G X2 SC LR Transceiver (J8437A)

An X2 form-factor transceiver that supports the 10-Gigabit LR standard, providing 10-Gigabit connectivity up to 10 km on single-mode fiber.

Ports 1 SC 10-GbE port (IEEE 802.3ae Type 10GBASE-LR); Duplex: full only


Wavelength 1310 nm











2 W


3 W

Cabling Cable type:: Low metal content, single-mode fiber-optic, complying with ITU-T G.652 and ISO/IEC 793-2 Type B1;

Maximum distance:

10 km

Cable length 2m to 10km with 9/125 ìm single-mode cable

Fiber type Single Mode

Notes Conditioning patch cord cables are not supported For fiber patch cords, use Ultra Physical Contact (UPC) surface termination/polish. Angled Physical Contact (APC) is not recommended


HP X131 10G X2 SC LRM Transceiver (J9144A)

An X2 form-factor transceiver that supports the 10-Gigabit LRM standard, providing 10-Gigabit connectivity up to 220 m on legacy multimode fiber.

Ports 1 SC 10-GbE port (IEEE 802.3aq Type 10GBASE-LRM); Duplex: full only











3.2 W






4.2 W

Cabling Cable type: 62.5/125 µm or 50/125 µm (core/cladding) diameter, graded-index, low metal content, multimode fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2 Type A1b or A1a, respectively (a mode conditioning patch cord may be needed in some multimode fiber installations);

Maximum distance: • 0.5-220m with 62.5 µm multimode cable @ 160/500 MHz*km • 0.5-220m with 62.5 µm multimode cable @ 200/500 MHz*km • 0.5-100m with 50 µm multimode cable @ 400/400 MHz*km • 0.5-220m with 50 µm multimode cable @ 500/500 MHz*km • 0.5-220m with 50 µm multimode cable @ 1500/500 MHz*km

Cable length .5m to 220m

Fiber type Multi Mode

Notes Wavelength: 1310nm For OM3 cable (50 ìm multimode @ 1500/500 MHz*km), a mode-conditioning patch cord is not required. Other multimode cables may require mode-conditioning patch cords to achieve the maximum distances listed above. For supported platforms and minimum software requirements to support this product, see the document titled "Support for the J9144A 10-GbE X2-SC LRM Optic" on the "HP 10-GbE Transceivers" Manuals Web page. Power Consumption: 4W Max


HP X112 100M SFP LC BX-D Transceiver (J9099B)

A small form-factor pluggable (SFP) 100-Megabit BX (bi-directional) "downstream" transceiver that provides 100 Mbps full-duplex connectivity up to 10 km on one strand of singlemode fiber. The J9099B connects to the J9100B "upstream" transceiver, or to any IEEE-standard 100BASE-BX10-U ("upstream") device.

Ports 1 LC 100BASE-BX10 port (IEEE 802.3ah Type 100BASE-BX10-D); Duplex: full only








Cabling Type:

Single-mode fiber optic, complying with ITU-T G.652;

Maximum distance:

0.5-10,000 m (single-mode fiber)

Notes Transmit wavelength: 1550 nm. Receive wavelength: 1310 nm. Power consumption is 1.1 watt maximum. For supported platforms and minimum software requirements to support




this product, see the document titled "Support for the HP BX Transceivers" on the "HP Mini-GBICs and SFPs" Manuals Web page. The J9099B connects to the J9100B "upstream" transceiver, or to any IEEE-standard 100BASE-BX10-U ("upstream") device. (A 100-BX-D transceiver can only connect to a 100-BX-U product. You cannot connect two 100-BX-D transceivers together.)


HP X112 100M SFP LC BX-U Transceiver (J9100B)

A small form-factor pluggable (SFP) 100-Megabit BX (bi-directional) "upstream" transceiver that provides 100 Mbps full-duplex connectivity up to 10 km on one strand of singlemode fiber. The J9100B connects to the J9099B "downstream" transceiver, or to any IEEE-standard 100BASE-BX10-D ("downstream") device.

Ports 1 LC 100BASE-BX10 port (IEEE 802.3ah Type 100BASE-BX10-U); Duplex: full only


Weight 0.07 lb. (.03 kg)






Cabling Type:

Single-mode fiber optic, complying with ITU-T G.652;

Maximum distance:


Notes For supported platforms and minimum software requirements to support this product, see the document titled "Support for the HP BX Transceivers" on the "HP Mini-GBICs and SFPs" Manuals Web page. The J9100B connects to the J9099B "downstream" transceiver, or to any IEEE-standard 100BASE-BX10- D ("downstream") device. (A 100-BX-U transceiver can only connect to a 100-BX-D product. You cannot connect two 100-BX-U transceivers together.) Transmit wavelength: 1310 nm. Receive wavelength: 1550 nm. Power consumption is 1.1 watts maximum.


HP X121 1G SFP LC LH Transceiver (J4860C)

A small form-factor pluggable (SFP) Gigabit LH transceiver that provides a full-duplex Gigabit solution up to 70 km on

Ports 1 LC 1000BASE-LH port (no IEEE standard exists for 1550 nm optics); Duplex: full only

Physical characteristics Dimensions: 2.17(d) x 0.60(w) x 0.46(h) in. (5.5 x 1.53 x 1.18 cm) Weight: 0.04 lb. (0.02 kg)

Environment Operating temperature: -40°F to 185°F (-40°C to 85°C)

Operating relative humidity: 0% to 95% @ 77°F (25°C), noncondensing

Nonoperating/Storage temperature: -40°F to 185°F (-40°C to 85°C)

Altitude: up to 10,000 ft. (3 km)





single-mode fiber. Cabling Cable type:

Low metal content, single-mode fiber-optic, complying with ITU-T G.652 and ISO/IEC 793-2 Type B1;

Maximum distance:

10-70,000 m (single-mode fiber)

Notes Power consumption is 0.8 watts typical with 1 watt maximum at 100% utilization. For distances less than 20 km, a 10 dB attenuator must be used. For distances between 20 km and 40 km, a 5 dB attenuator must be used. Attenuators can be purchased from most cable vendors.


HP X121 1G SFP LC SX Transceiver (J4858C)

A small form-factor pluggable (SFP) Gigabit SX transceiver that provides a full-duplex Gigabit solution up to 550 m on multimode fiber.

Ports 1 LC 1000BASE-SX port; Duplex: full only

Physical characteristics Dimensions: 2.24(d) x 0.54(w) x 0.48(h) in. (5.69 x 1.37 x 1.22 cm) Weight: 0.04 lb. (0.02 kg) Transceiver form factor: SFP

Environment Operating temperature: 32°F to 158°F (0°C to 70°C)

Operating relative humidity: 5% to 85%, noncondensing



Electrical characteristics Power consumption typical: 0.4 W

Power consumption maximum: 0.7 W

Cabling Type:

62.5/125 µm or 50/125 µm (core/cladding) diameter, graded-index, low metal content, multimode fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2 Type A1b or A1a, respectively;

Maximum distance:

2-220 m (62.5 µm core diameter, 160 MHz*km bandwidth 2-275 m (62.5 µm core diameter, 200 MHz*km bandwidth 2-500 m (50 µm core diameter, 400 MHz*km bandwidth) 2-550 m (50 µm core diameter, 500 MHz*km bandwidth)

Cable length: 2-550m

Fiber type: Multi Mode


HP X121 1G SFP LC LX Ports 1 LC 1000BASE-LX port (IEEE 802.3z Type 1000BASE-LX); Duplex: full only

Physical characteristics Dimensions: 2.24(d) x 0.54(w) x 0.486(h) in. (5.69 x 1.37 x 1.23 cm) Weight:0.04 lb. (0.02 kg)





Transceiver (J4859C)

HP X121 1G SFP LC LX Transceiver: An SFP format gigabit transceiver with LC connectors using LX technology.

Environment Operating temperature: 32°F to 158°F (0°C to 70°C)

Operating relative humidity: 0% to 85%, noncondensing



Cabling Type:

Either single mode or multimode; 62.5/125 µm or 50/125 µm (core/cladding) diameter, graded-index, low metal content, multimode fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2 Type A1b or A1a, respectively; Low metal content, single-mode fiber-optic, complying with ITU-T G.652 and ISO/IEC 793-2 Type B1;

Maximum distance:

2-550 m (multimode 62.5 µm core diameter, 500 MHz*km bandwidth)

2-550 m (multimode 50 µm core diameter, 400 MHz*km bandwidth)

2-550 m (multimode 50 µm core diameter, 500 MHz*km bandwidth)

2-10,000 m (single-mode fiber)

Notes A mode conditioning patch cord may be needed in some multimode fiber installations. Wavelength: 1310nm Power Consumption: < 500mW Typical


HP X122 1G SFP LC BX-D Transceiver (J9142B)

A small form-factor pluggable (SFP) Gigabit-BX (bi-directional) "downstream" transceiver that provides a full-duplex Gigabit solution up to 10 km on one strand of single-mode fiber. The J9142B connects to the J9143B "upstream" transceiver, or to any IEEE-standard 1000BASE-BX10-U ("upstream") device.

Ports 1 LC 1000BASE-BX10 port (IEEE 802.3ah Type 1000BASE-BX10-D); Duplex: full only





0% to 95%, non-condensing


–40ºF to 185ºF –40ºC to 85ºC)

Cabling Type: Single-mode fiber optic, complying with ITU-T G.652;

Maximum distance:


Notes Transmit wavelength: 1490 nm. Receive wavelength: 1310 nm. Power consumption is 1 watt maximum.





For supported platforms and minimum software requirements to support this product, see the document titled "Support for the HP BX Transceivers" on the "HP Mini-GBICs and SFPs" Manuals Web page. The J9142B connects to the J9143B "upstream" transceiver, or to any IEEE-standard 1000BASE-BX10-U ("upstream") device. (A 1000-BX-D transceiver can only connect to a 1000-BX-U product. You cannot connect two 1000-BX-D transceivers together.)


HP X122 1G SFP LC BX-U Transceiver (J9143B)

A small form-factor pluggable (SFP) Gigabit-BX (bi-directional) "upstream" transceiver that provides a full-duplex Gigabit solution up to 10 km on one strand of single-mode fiber. The J9143B connects to the J9142B "downstream" transceiver, or to any IEEE-standard 1000BASE-BX10-D ("downstream") device.

Ports 1 LC 1000BASE-BX10 port (IEEE 802.3ah Type 1000BASE-BX10-U); Duplex: full only





0% to 95%, non-condensing


–40ºF to 185ºF –40ºC to 85ºC)

Cabling Type: Single-mode fiber optic, complying with ITU-T G.652;

Maximum distance:


Notes Transmit wavelength: 1310 nm. Receive wavelength: 1490 nm. For supported platforms and minimum software requirements to support this product, see the document titled "Support for the HP BX Transceivers" on the "HP Mini-GBICs and SFPs" Manuals Web page. The J9143B connects to the J9142B "downstream" transceiver, or to any IEEE-standard 1000BASE-BX10-D ("downstream") device. (A 1000-BX-U transceiver can only connect to a 1000-BX-D product. You cannot connect two 1000-BX-U transceivers together.) Power consumption is 1 watt maximum.

Services Refer to the HP website at: www.hp.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local HP sales office.

HP 0.5 m Multimode OM3 LC/LC Optical Cable (AJ833A)

Cabling Cable type: 50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of up to 300 m

Maximum distance: 10Gbps Transfer Rate (Ethernet): 300m

Notes Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um fiber optic cable and Ethernet assembly with LC duplex connectors on one





end and LC duplex connectors on other end.

Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um Coating diameter: 245 ± 10um

Optical glass: Bandwidth: For LED sources: 1500/500 MHz-km @850/1300nm.

Optical glass: Bandwidth: For Laser sources: 2000/500 MHz-km @850/1300nm. VCSEL Laser sources: 600 / 600 meters @850/1300nm for Gigabit Ethernet compliant links.

CABLE: The cable is duplex zipcord graded index 50/125um multimode optical fiber and designed to work in both the 850 and 1300 nm wavelength windows.

BULK CABLE & CABLE ASSEMBLY CONFIGURATION: Jacket Material: Riser Grade - Low Smoke Zero Halogen

thermoplastic. Jacket Color: Aqua for OM3 multimode per TIA 598 Boot Color: White Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003

dB/M added for lengths > 30 meters. Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @

1310 nm @ 23°C as tested in accordance with EIA 455-46. Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg


HP Premier Flex LC/LC Multi-mode OM4 2 fiber 1m Cable (QK732A)

Notes Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um duplex cable and Ethernet assembly with LC duplex connectors on each end.

• Core Diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating diameter: 245 ± 10um • Bandwidth: 3000 MHz-km @ 850nm (Laser) • Jacket Color: Blue • Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH) thermoplastic • Boot Color: White • Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white stripe that runs the entire length of the cable. • Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added for lengths >30m • Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @ 23°C as tested in accordance with EIA 455-45


HP Premier Flex LC/LC Multi-mode OM4 2 fiber

Notes Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um duplex cable and Ethernet assembly with LC duplex connectors





2m Cable (QK733A) on each end.

• Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating diameter: 245 ± 10um • Bandwidth: 3000 MHz-km @ 850nm (Laser) • Jacket Color: Blue • Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH) thermoplastic • Boot Color: White • Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white stripe that runs the entire length of the cable. • Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added for lengths >30m • Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @ 23°C as tested in accordance with EIA 455-45








• Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating diameter: 245 ± 10um • Bandwidth: 3000 MHz-km @ 850nm (Laser) • Jacket Color: Blue • Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH) thermoplastic





• Boot Color: White • Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white stripe that runs the entire length of the cable. • Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added for lengths >30m • Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @ 23°C as tested in accordance with EIA 455-45











Summary of Changes


Date Version History Action Description of Change: 24-Jul-2015 From Version 20 to

21 Changed This QuickSpecs was retired; no further updates will be

made. 09-Oct-2014 From Version 19 to

20 Changed Accessory Product Details were revised

15-Apr-2014 From Version 18 to 19

Changed Notes sections were revised throughout Configuration.

17-Jan-2014 From Version 17 to 18

Changed Factory Racked Models and Switch Options were revised.

09-Dec-2013 From Version 16 to 17

Changed Updated Features and Benefits, Introduction, the specifications, and Accessories, as well as the title of the document.

11-Nov-2013 From Version 15 to 16

Added Configuration was added.

10-Jun-2013 From Version 14 to 15

Added OM4 cables were added.

24-Sep-2012 From Version 13 to 14

Changed Updated Features and Benefits, Introduction, the specifications, and Accessories.


Changed Updated Features and Benefits, Introduction, the specifications, and Accessories.

29-Nov-2011 From Version 11 to 12

Changed The Features and Benefits section was updated.


Changed Updated the Accessories section.

14-Dec-2010 From Version 9 to 10 Changed Corrected the Accessories section. 09-Sep-2010 From Version 8 to 9 Changed The document was updated throughout to reflect the new

name of this products as well as other HP Networking products.

02-Jun-2010 From Version 7 to 8 Changed Updated the Notes section of Technical Specifications.

Updated Standards and Protocols

Added new cables to the Accessories section. 04-Mar-2010 From Version 6 to 7 Changed The QuickSpec was completely revised. 16-Mar-2009 From Version 5 to 6 Changed The Features, Accessories, Services, and Specifications

(Performance, Environment, Electrical characteristics, Management, Standards and protocols) have changed for this product

01-Dec-2008 From Version 3 to 5 Added "HP" to ProCurve Switch 6200yl-24G-mGBIC throughout the QuickSpec, including in the title

IPv6 to Connectivity in the Features and Benefits section and Standards and Protocols in the Technical Specifications section

USB Secure Autorun and STP Root Guard to Security

Classified-based rate limits to Quality of Services (QoS)

HP ProCurve 100-BX-D SFP-LC and HP ProCurve 100-BX-U SFP-LC Transceivers, HP ProCurve 1000-Bx-D SFP-LC


Summary of Changes


Mini-GBIC, HP ProCurve 1000-BX-U SFP-LC Mini-GBIC and HP ProCurve 10-GbE X2-SC LRM Optic to Accessories

Changed Remote intelligent mirror in Management in the Features and Benefits section

ProCurve trunking increased to 60 trunks in IEEE 802.3ad Link Aggregation Control Protocol (LACP) in the Features and Benefits section

Static IP Routing and OSPF in Layer 3 Routing in the Features and Benefits section

Multiple user authentication methods in the Features and Benefits section

16-Nov-2006 From Version 2 to 3 Changed Corrected the Current and Power consumption specifications.

18-Aug-2006 From Version 1 to 2 Changed Changes made throughout the QuickSpec.

To learn more, visit www.hp.com/networking

© Copyright 2015 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.

http://www.hp.com/networking

hp 6200 yl switch series - andover consulting group · 2015-11-30 · quickspecs hp 6200 yl switch...

Documents