how to use this install guide · 2020. 8. 26. · ads-ar-dc-dfo2 products required rockford fosgate...
TRANSCRIPT
-
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WARNING Pressing the printer icon or “quick printing” this document will print
all of the guides in this compilation.
Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle.
Print only the pages for your vehicle using the advanced options in the Print menu.
Install your DSR1 module according to the guide for your vehicle.
HOW TO USE THIS INSTALL GUIDE1
2
3
SELECT VEHICLE PRINT PAGES NEEDED
-
OPTIONAL ACCESSORIES PROGRAMMED FIRMWAREADS-AR-DC-dFO2
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro DSP-FO2 Installation Harness
INSTALL GUIDEFORD CMAx
2013-2018ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,
WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD CMAx 2013-2018
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD CMAx 2013-2018
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory radio and plug the dFO2 T-harness in line with the radio plug.
STEP 2• Connect the wires from the dFO2 T-harness to the
aftermarket amplifi er.
Note 1:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 3• Connect all the harnesses to the DSR1 module.
STEP 4Program the OEM radio to “amplifi ed mode”.
• Close vehicle doors.
• Turn ignition ON-OFF-ON.
• Wait for radio to be completely booted.
• Set the audio source to OFF.
• Cycle the parking brake ON–OFF–ON.
• Push and hold Volume+ button on the steering wheel. The radio screen will change to FM and will show volume 0. Release the button.
• Screen will show Volume 10 – 20 - 30.
The DSR1 module is now locked to this particular vehicle by VIN number.
Note: If you need to return the radio to its factory non-amplifi ed mode, do this programming procedure and press and hold VOL– button on the steering wheel instead. The radio screen will change to FM and will show volume 0. Release the button. The radio screen will show Volume (30 – 20 - 0). The de-programming sequence is complete.
The DSR1 is now unlocked from the vehicle.
CHIME ADJUSTMENTFront chime
Set Audio source to OFF.
Activate front chime (Ex: door chime).
Adjust using the radio’s volume knob.
Rear chime
Set Audio source to OFF
Activate Rear chime (Ex: Rear parking assist)
Adjust using the radio’s volume knob
TROUBLESHOOTING TIPS:
• To reset the DSR1 module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Wait 15 seconds and re-connect all the connectors back to the module.
For technical assistance :
Call : 1-866-427-2999
E-mail : [email protected]
Visit us at : maestro.idatalink.com/support and www.12voltdata.com/forum/
1
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD CMAx 2013-2018
Automotive Data Solutions Inc. © 2020 4
1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
WIRING DIAGRAMSTEP 2
STEP 3DSR1 MODULE
RCA CABLES
AFTERMARKET AMPLIFIER
STEP 1
dFO2 T-HARNESS
WHITE (LEFT FRONT)WHITE/BLACK (LEFT FRONT)GRAY (RIGHT FRONT)GRAY/BLACK (RIGHT FRONT)GREEN (LEFT REAR)GREEN/BLACK (LEFT REAR)
PURPLE/BLACK (RIGHT REAR)
(NC) AMP TURN ON
PURPLE (RIGHT REAR)
CONNECT TO OEMRADIO CONNECTOR
CONNECT TO OEMRADIO HARNESS
-
OPTIONAL ACCESSORIES PROGRAMMED FIRMWAREADS-AR-DC-dFO2
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro DSP-FO2 Installation Harness
INSTALL GUIDEFORD EDGE 2011-2019
ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD EDGE 2011-2019
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD EDGE 2011-2019
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory radio and plug the dFO2 T-harness in line with the radio plug.
STEP 2• Connect the wires from the dFO2 T-harness to the
aftermarket amplifi er.
Note 1:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 3• Connect all the harnesses to the DSR1 module.
STEP 4Program the OEM radio to “amplifi ed mode”.
• Close vehicle doors.
• Turn ignition ON-OFF-ON.
• Wait for radio to be completely booted.
• Set the audio source to OFF.
• Cycle the parking brake ON–OFF–ON.
• Push and hold Volume+ button on the steering wheel. The radio screen will change to FM and will show volume 0. Release the button.
• Screen will show Volume 10 – 20 - 30.
The DSR1 module is now locked to this particular vehicle by VIN number.
Note: If you need to return the radio to its factory non-amplifi ed mode, do this programming procedure and press and hold VOL– button on the steering wheel instead. The radio screen will change to FM and will show volume 0. Release the button. The radio screen will show Volume (30 – 20 - 0). The de-programming sequence is complete.
The DSR1 is now unlocked from the vehicle.
CHIME ADJUSTMENTFront chime
Set Audio source to OFF.
Activate front chime (Ex: door chime).
Adjust using the radio’s volume knob.
Rear chime
Set Audio source to OFF
Activate Rear chime (Ex: Rear parking assist)
Adjust using the radio’s volume knob
TROUBLESHOOTING TIPS:
• To reset the DSR1 module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Wait 15 seconds and re-connect all the connectors back to the module.
For technical assistance :
Call : 1-866-427-2999
E-mail : [email protected]
Visit us at : maestro.idatalink.com/support and www.12voltdata.com/forum/
1
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD EDGE 2011-2019
Automotive Data Solutions Inc. © 2020 4
1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
WIRING DIAGRAMSTEP 2
STEP 3DSR1 MODULE
RCA CABLES
AFTERMARKET AMPLIFIER
STEP 1
dFO2 T-HARNESS
WHITE (LEFT FRONT)WHITE/BLACK (LEFT FRONT)GRAY (RIGHT FRONT)GRAY/BLACK (RIGHT FRONT)GREEN (LEFT REAR)GREEN/BLACK (LEFT REAR)
PURPLE/BLACK (RIGHT REAR)
(NC) AMP TURN ON
PURPLE (RIGHT REAR)
CONNECT TO OEMRADIO CONNECTOR
CONNECT TO OEMRADIO HARNESS
-
OPTIONAL ACCESSORIES PROGRAMMED FIRMWAREADS-AR-DC-dFO2
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro DSP-FO2 Installation Harness
INSTALL GUIDEFORD ESCAPE
2013-2019ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,
WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD ESCAPE 2013-2019
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD ESCAPE 2013-2019
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory radio and plug the dFO2 T-harness in line with the radio plug.
STEP 2• Connect the wires from the dFO2 T-harness to the
aftermarket amplifi er.
Note 1:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 3• Connect all the harnesses to the DSR1 module.
STEP 4Program the OEM radio to “amplifi ed mode”.
• Close vehicle doors.
• Turn ignition ON-OFF-ON.
• Wait for radio to be completely booted.
• Set the audio source to OFF.
• Cycle the parking brake ON–OFF–ON.
• Push and hold Volume+ button on the steering wheel. The radio screen will change to FM and will show volume 0. Release the button.
• Screen will show Volume 10 – 20 - 30.
The DSR1 module is now locked to this particular vehicle by VIN number.
Note: If you need to return the radio to its factory non-amplifi ed mode, do this programming procedure and press and hold VOL– button on the steering wheel instead. The radio screen will change to FM and will show volume 0. Release the button. The radio screen will show Volume (30 – 20 - 0). The de-programming sequence is complete.
The DSR1 is now unlocked from the vehicle.
CHIME ADJUSTMENTFront chime
Set Audio source to OFF.
Activate front chime (Ex: door chime).
Adjust using the radio’s volume knob.
Rear chime
Set Audio source to OFF
Activate Rear chime (Ex: Rear parking assist)
Adjust using the radio’s volume knob
TROUBLESHOOTING TIPS:
• To reset the DSR1 module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Wait 15 seconds and re-connect all the connectors back to the module.
For technical assistance :
Call : 1-866-427-2999
E-mail : [email protected]
Visit us at : maestro.idatalink.com/support and www.12voltdata.com/forum/
1
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD ESCAPE 2013-2019
Automotive Data Solutions Inc. © 2020 4
1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
WIRING DIAGRAMSTEP 2
STEP 3DSR1 MODULE
RCA CABLES
AFTERMARKET AMPLIFIER
STEP 1
dFO2 T-HARNESS
WHITE (LEFT FRONT)WHITE/BLACK (LEFT FRONT)GRAY (RIGHT FRONT)GRAY/BLACK (RIGHT FRONT)GREEN (LEFT REAR)GREEN/BLACK (LEFT REAR)
PURPLE/BLACK (RIGHT REAR)
(NC) AMP TURN ON
PURPLE (RIGHT REAR)
CONNECT TO OEMRADIO CONNECTOR
CONNECT TO OEMRADIO HARNESS
-
OPTIONAL ACCESSORIES PROGRAMMED FIRMWAREADS-AR-DC-dFO2
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro DSP-FO2 Installation Harness
INSTALL GUIDEFORD ExPEDITION
2015-2020ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,
WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD ExPEDITION 2015-2020
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD ExPEDITION 2015-2020
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory radio and plug the dFO2 T-harness in line with the radio plug.
STEP 2• Connect the wires from the dFO2 T-harness to the
aftermarket amplifi er.
Note 1:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 3• Connect all the harnesses to the DSR1 module.
STEP 4Program the OEM radio to “amplifi ed mode”.
• Close vehicle doors.
• Turn ignition ON-OFF-ON.
• Wait for radio to be completely booted.
• Set the audio source to OFF.
• Cycle the parking brake ON–OFF–ON.
• Push and hold Volume+ button on the steering wheel. The radio screen will change to FM and will show volume 0. Release the button.
• Screen will show Volume 10 – 20 - 30.
The DSR1 module is now locked to this particular vehicle by VIN number.
Note: If you need to return the radio to its factory non-amplifi ed mode, do this programming procedure and press and hold VOL– button on the steering wheel instead. The radio screen will change to FM and will show volume 0. Release the button. The radio screen will show Volume (30 – 20 - 0). The de-programming sequence is complete.
The DSR1 is now unlocked from the vehicle.
CHIME ADJUSTMENTFront chime
Set Audio source to OFF.
Activate front chime (Ex: door chime).
Adjust using the radio’s volume knob.
Rear chime
Set Audio source to OFF
Activate Rear chime (Ex: Rear parking assist)
Adjust using the radio’s volume knob
TROUBLESHOOTING TIPS:
• To reset the DSR1 module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Wait 15 seconds and re-connect all the connectors back to the module.
For technical assistance :
Call : 1-866-427-2999
E-mail : [email protected]
Visit us at : maestro.idatalink.com/support and www.12voltdata.com/forum/
1
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD ExPEDITION 2015-2020
Automotive Data Solutions Inc. © 2020 4
1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
WIRING DIAGRAMSTEP 2
STEP 3DSR1 MODULE
RCA CABLES
AFTERMARKET AMPLIFIER
STEP 1
dFO2 T-HARNESS
WHITE (LEFT FRONT)WHITE/BLACK (LEFT FRONT)GRAY (RIGHT FRONT)GRAY/BLACK (RIGHT FRONT)GREEN (LEFT REAR)GREEN/BLACK (LEFT REAR)
PURPLE/BLACK (RIGHT REAR)
(NC) AMP TURN ON
PURPLE (RIGHT REAR)
CONNECT TO OEMRADIO CONNECTOR
CONNECT TO OEMRADIO HARNESS
-
OPTIONAL ACCESSORIES PROGRAMMED FIRMWAREADS-AR-DC-dFO2
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro DSP-FO2 Installation Harness
INSTALL GUIDEFORD ExPLORER
2011-2019ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,
WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD ExPLORER 2011-2019
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD ExPLORER 2011-2019
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory radio and plug the dFO2 T-harness in line with the radio plug.
STEP 2• Connect the wires from the dFO2 T-harness to the
aftermarket amplifi er.
Note 1:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 3• Connect all the harnesses to the DSR1 module.
STEP 4Program the OEM radio to “amplifi ed mode”.
• Close vehicle doors.
• Turn ignition ON-OFF-ON.
• Wait for radio to be completely booted.
• Set the audio source to OFF.
• Cycle the parking brake ON–OFF–ON.
• Push and hold Volume+ button on the steering wheel. The radio screen will change to FM and will show volume 0. Release the button.
• Screen will show Volume 10 – 20 - 30.
The DSR1 module is now locked to this particular vehicle by VIN number.
Note: If you need to return the radio to its factory non-amplifi ed mode, do this programming procedure and press and hold VOL– button on the steering wheel instead. The radio screen will change to FM and will show volume 0. Release the button. The radio screen will show Volume (30 – 20 - 0). The de-programming sequence is complete.
The DSR1 is now unlocked from the vehicle.
CHIME ADJUSTMENTFront chime
Set Audio source to OFF.
Activate front chime (Ex: door chime).
Adjust using the radio’s volume knob.
Rear chime
Set Audio source to OFF
Activate Rear chime (Ex: Rear parking assist)
Adjust using the radio’s volume knob
TROUBLESHOOTING TIPS:
• To reset the DSR1 module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Wait 15 seconds and re-connect all the connectors back to the module.
For technical assistance :
Call : 1-866-427-2999
E-mail : [email protected]
Visit us at : maestro.idatalink.com/support and www.12voltdata.com/forum/
1
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD ExPLORER 2011-2019
Automotive Data Solutions Inc. © 2020 4
1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
WIRING DIAGRAMSTEP 2
STEP 3DSR1 MODULE
RCA CABLES
AFTERMARKET AMPLIFIER
STEP 1
dFO2 T-HARNESS
WHITE (LEFT FRONT)WHITE/BLACK (LEFT FRONT)GRAY (RIGHT FRONT)GRAY/BLACK (RIGHT FRONT)GREEN (LEFT REAR)GREEN/BLACK (LEFT REAR)
PURPLE/BLACK (RIGHT REAR)
(NC) AMP TURN ON
PURPLE (RIGHT REAR)
CONNECT TO OEMRADIO CONNECTOR
CONNECT TO OEMRADIO HARNESS
-
OPTIONAL ACCESSORIES PROGRAMMED FIRMWAREADS-AR-DC-dFO2
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro DSP-FO2 Installation Harness
INSTALL GUIDEFORD F SUPER DUTy
2017-2019ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,
WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD F SUPER DUTY 2017-2019
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD F SUPER DUTY 2017-2019
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory radio and plug the dFO2 T-harness in line with the radio plug.
STEP 2• Connect the wires from the dFO2 T-harness to the
aftermarket amplifi er.
Note 1:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 3• Connect all the harnesses to the DSR1 module.
STEP 4Program the OEM radio to “amplifi ed mode”.
• Close vehicle doors.
• Turn ignition ON-OFF-ON.
• Wait for radio to be completely booted.
• Set the audio source to OFF.
• Cycle the parking brake ON–OFF–ON.
• Push and hold Volume+ button on the steering wheel. The radio screen will change to FM and will show volume 0. Release the button.
• Screen will show Volume 10 – 20 - 30.
The DSR1 module is now locked to this particular vehicle by VIN number.
Note: If you need to return the radio to its factory non-amplifi ed mode, do this programming procedure and press and hold VOL– button on the steering wheel instead. The radio screen will change to FM and will show volume 0. Release the button. The radio screen will show Volume (30 – 20 - 0). The de-programming sequence is complete.
The DSR1 is now unlocked from the vehicle.
CHIME ADJUSTMENTFront chime
Set Audio source to OFF.
Activate front chime (Ex: door chime).
Adjust using the radio’s volume knob.
Rear chime
Set Audio source to OFF
Activate Rear chime (Ex: Rear parking assist)
Adjust using the radio’s volume knob
TROUBLESHOOTING TIPS:
• To reset the DSR1 module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Wait 15 seconds and re-connect all the connectors back to the module.
For technical assistance :
Call : 1-866-427-2999
E-mail : [email protected]
Visit us at : maestro.idatalink.com/support and www.12voltdata.com/forum/
1
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD F SUPER DUTY 2017-2019
Automotive Data Solutions Inc. © 2020 4
1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
WIRING DIAGRAMSTEP 2
STEP 3DSR1 MODULE
RCA CABLES
AFTERMARKET AMPLIFIER
STEP 1
dFO2 T-HARNESS
WHITE (LEFT FRONT)WHITE/BLACK (LEFT FRONT)GRAY (RIGHT FRONT)GRAY/BLACK (RIGHT FRONT)GREEN (LEFT REAR)GREEN/BLACK (LEFT REAR)
PURPLE/BLACK (RIGHT REAR)
(NC) AMP TURN ON
PURPLE (RIGHT REAR)
CONNECT TO OEMRADIO CONNECTOR
CONNECT TO OEMRADIO HARNESS
-
OPTIONAL ACCESSORIES PROGRAMMED FIRMWAREADS-AR-DC-dFO2
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro DSP-FO2 Installation Harness
INSTALL GUIDEFORD F150 2013-2019
ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD F150 2013-2019
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD F150 2013-2019
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory radio and plug the dFO2 T-harness in line with the radio plug.
STEP 2• Connect the wires from the dFO2 T-harness to the
aftermarket amplifi er.
Note 1:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 3• Connect all the harnesses to the DSR1 module.
STEP 4Program the OEM radio to “amplifi ed mode”.
• Close vehicle doors.
• Turn ignition ON-OFF-ON.
• Wait for radio to be completely booted.
• Set the audio source to OFF.
• Cycle the parking brake ON–OFF–ON.
• Push and hold Volume+ button on the steering wheel. The radio screen will change to FM and will show volume 0. Release the button.
• Screen will show Volume 10 – 20 - 30.
The DSR1 module is now locked to this particular vehicle by VIN number.
Note: If you need to return the radio to its factory non-amplifi ed mode, do this programming procedure and press and hold VOL– button on the steering wheel instead. The radio screen will change to FM and will show volume 0. Release the button. The radio screen will show Volume (30 – 20 - 0). The de-programming sequence is complete.
The DSR1 is now unlocked from the vehicle.
CHIME ADJUSTMENTFront chime
Set Audio source to OFF.
Activate front chime (Ex: door chime).
Adjust using the radio’s volume knob.
Rear chime
Set Audio source to OFF
Activate Rear chime (Ex: Rear parking assist)
Adjust using the radio’s volume knob
TROUBLESHOOTING TIPS:
• To reset the DSR1 module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Wait 15 seconds and re-connect all the connectors back to the module.
For technical assistance :
Call : 1-866-427-2999
E-mail : [email protected]
Visit us at : maestro.idatalink.com/support and www.12voltdata.com/forum/
1
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD F150 2013-2019
Automotive Data Solutions Inc. © 2020 4
1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
WIRING DIAGRAMSTEP 2
STEP 3DSR1 MODULE
RCA CABLES
AFTERMARKET AMPLIFIER
STEP 1
dFO2 T-HARNESS
WHITE (LEFT FRONT)WHITE/BLACK (LEFT FRONT)GRAY (RIGHT FRONT)GRAY/BLACK (RIGHT FRONT)GREEN (LEFT REAR)GREEN/BLACK (LEFT REAR)
PURPLE/BLACK (RIGHT REAR)
(NC) AMP TURN ON
PURPLE (RIGHT REAR)
CONNECT TO OEMRADIO CONNECTOR
CONNECT TO OEMRADIO HARNESS
-
OPTIONAL ACCESSORIES PROGRAMMED FIRMWAREADS-AR-DC-dFO2
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro DSP-FO2 Installation Harness
INSTALL GUIDEFORD FOCUS
2012-2018ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,
WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD FOCUS 2012-2018
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD FOCUS 2012-2018
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory radio and plug the dFO2 T-harness in line with the radio plug.
STEP 2• Connect the wires from the dFO2 T-harness to the
aftermarket amplifi er.
Note 1:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 3• Connect all the harnesses to the DSR1 module.
STEP 4Program the OEM radio to “amplifi ed mode”.
• Close vehicle doors.
• Turn ignition ON-OFF-ON.
• Wait for radio to be completely booted.
• Set the audio source to OFF.
• Cycle the parking brake ON–OFF–ON.
• Push and hold Volume+ button on the steering wheel. The radio screen will change to FM and will show volume 0. Release the button.
• Screen will show Volume 10 – 20 - 30.
The DSR1 module is now locked to this particular vehicle by VIN number.
Note: If you need to return the radio to its factory non-amplifi ed mode, do this programming procedure and press and hold VOL– button on the steering wheel instead. The radio screen will change to FM and will show volume 0. Release the button. The radio screen will show Volume (30 – 20 - 0). The de-programming sequence is complete.
The DSR1 is now unlocked from the vehicle.
CHIME ADJUSTMENTFront chime
Set Audio source to OFF.
Activate front chime (Ex: door chime).
Adjust using the radio’s volume knob.
Rear chime
Set Audio source to OFF
Activate Rear chime (Ex: Rear parking assist)
Adjust using the radio’s volume knob
TROUBLESHOOTING TIPS:
• To reset the DSR1 module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Wait 15 seconds and re-connect all the connectors back to the module.
For technical assistance :
Call : 1-866-427-2999
E-mail : [email protected]
Visit us at : maestro.idatalink.com/support and www.12voltdata.com/forum/
1
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD FOCUS 2012-2018
Automotive Data Solutions Inc. © 2020 4
1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
WIRING DIAGRAMSTEP 2
STEP 3DSR1 MODULE
RCA CABLES
AFTERMARKET AMPLIFIER
STEP 1
dFO2 T-HARNESS
WHITE (LEFT FRONT)WHITE/BLACK (LEFT FRONT)GRAY (RIGHT FRONT)GRAY/BLACK (RIGHT FRONT)GREEN (LEFT REAR)GREEN/BLACK (LEFT REAR)
PURPLE/BLACK (RIGHT REAR)
(NC) AMP TURN ON
PURPLE (RIGHT REAR)
CONNECT TO OEMRADIO CONNECTOR
CONNECT TO OEMRADIO HARNESS
-
OPTIONAL ACCESSORIES PROGRAMMED FIRMWAREADS-AR-DC-dFO2
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro DSP-FO2 Installation Harness
INSTALL GUIDEFORD FUSION
2013-2019ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,
WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD FUSION 2013-2019
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD FUSION 2013-2019
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory radio and plug the dFO2 T-harness in line with the radio plug.
STEP 2• Connect the wires from the dFO2 T-harness to the
aftermarket amplifi er.
Note 1:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 3• Connect all the harnesses to the DSR1 module.
STEP 4Program the OEM radio to “amplifi ed mode”.
• Close vehicle doors.
• Turn ignition ON-OFF-ON.
• Wait for radio to be completely booted.
• Set the audio source to OFF.
• Cycle the parking brake ON–OFF–ON.
• Push and hold Volume+ button on the steering wheel. The radio screen will change to FM and will show volume 0. Release the button.
• Screen will show Volume 10 – 20 - 30.
The DSR1 module is now locked to this particular vehicle by VIN number.
Note: If you need to return the radio to its factory non-amplifi ed mode, do this programming procedure and press and hold VOL– button on the steering wheel instead. The radio screen will change to FM and will show volume 0. Release the button. The radio screen will show Volume (30 – 20 - 0). The de-programming sequence is complete.
The DSR1 is now unlocked from the vehicle.
CHIME ADJUSTMENTFront chime
Set Audio source to OFF.
Activate front chime (Ex: door chime).
Adjust using the radio’s volume knob.
Rear chime
Set Audio source to OFF
Activate Rear chime (Ex: Rear parking assist)
Adjust using the radio’s volume knob
TROUBLESHOOTING TIPS:
• To reset the DSR1 module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Wait 15 seconds and re-connect all the connectors back to the module.
For technical assistance :
Call : 1-866-427-2999
E-mail : [email protected]
Visit us at : maestro.idatalink.com/support and www.12voltdata.com/forum/
1
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD FUSION 2013-2019
Automotive Data Solutions Inc. © 2020 4
1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
WIRING DIAGRAMSTEP 2
STEP 3DSR1 MODULE
RCA CABLES
AFTERMARKET AMPLIFIER
STEP 1
dFO2 T-HARNESS
WHITE (LEFT FRONT)WHITE/BLACK (LEFT FRONT)GRAY (RIGHT FRONT)GRAY/BLACK (RIGHT FRONT)GREEN (LEFT REAR)GREEN/BLACK (LEFT REAR)
PURPLE/BLACK (RIGHT REAR)
(NC) AMP TURN ON
PURPLE (RIGHT REAR)
CONNECT TO OEMRADIO CONNECTOR
CONNECT TO OEMRADIO HARNESS
-
OPTIONAL ACCESSORIES PROGRAMMED FIRMWAREADS-AR-DC-dFO2
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro DSP-FO2 Installation Harness
INSTALL GUIDEFORD MUSTANG
2015-2019ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,
WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD MUSTANG 2015-2019
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD MUSTANG 2015-2019
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory radio and plug the dFO2 T-harness in line with the radio plug.
STEP 2• Connect the wires from the dFO2 T-harness to the
aftermarket amplifi er.
Note 1:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 3• Connect all the harnesses to the DSR1 module.
STEP 4Program the OEM radio to “amplifi ed mode”.
• Close vehicle doors.
• Turn ignition ON-OFF-ON.
• Wait for radio to be completely booted.
• Set the audio source to OFF.
• Cycle the parking brake ON–OFF–ON.
• Push and hold Volume+ button on the steering wheel. The radio screen will change to FM and will show volume 0. Release the button.
• Screen will show Volume 10 – 20 - 30.
The DSR1 module is now locked to this particular vehicle by VIN number.
Note: If you need to return the radio to its factory non-amplifi ed mode, do this programming procedure and press and hold VOL– button on the steering wheel instead. The radio screen will change to FM and will show volume 0. Release the button. The radio screen will show Volume (30 – 20 - 0). The de-programming sequence is complete.
The DSR1 is now unlocked from the vehicle.
CHIME ADJUSTMENTFront chime
Set Audio source to OFF.
Activate front chime (Ex: door chime).
Adjust using the radio’s volume knob.
Rear chime
Set Audio source to OFF
Activate Rear chime (Ex: Rear parking assist)
Adjust using the radio’s volume knob
TROUBLESHOOTING TIPS:
• To reset the DSR1 module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Wait 15 seconds and re-connect all the connectors back to the module.
For technical assistance :
Call : 1-866-427-2999
E-mail : [email protected]
Visit us at : maestro.idatalink.com/support and www.12voltdata.com/forum/
1
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD MUSTANG 2015-2019
Automotive Data Solutions Inc. © 2020 4
1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
WIRING DIAGRAMSTEP 2
STEP 3DSR1 MODULE
RCA CABLES
AFTERMARKET AMPLIFIER
STEP 1
dFO2 T-HARNESS
WHITE (LEFT FRONT)WHITE/BLACK (LEFT FRONT)GRAY (RIGHT FRONT)GRAY/BLACK (RIGHT FRONT)GREEN (LEFT REAR)GREEN/BLACK (LEFT REAR)
PURPLE/BLACK (RIGHT REAR)
(NC) AMP TURN ON
PURPLE (RIGHT REAR)
CONNECT TO OEMRADIO CONNECTOR
CONNECT TO OEMRADIO HARNESS
-
OPTIONAL ACCESSORIES PROGRAMMED FIRMWAREADS-AR-DC-dFO2
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro DSP-FO2 Installation Harness
INSTALL GUIDEFORD TAURUS
2013-2019ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,
WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD TAURUS 2013-2019
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD TAURUS 2013-2019
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory radio and plug the dFO2 T-harness in line with the radio plug.
STEP 2• Connect the wires from the dFO2 T-harness to the
aftermarket amplifi er.
Note 1:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 3• Connect all the harnesses to the DSR1 module.
STEP 4Program the OEM radio to “amplifi ed mode”.
• Close vehicle doors.
• Turn ignition ON-OFF-ON.
• Wait for radio to be completely booted.
• Set the audio source to OFF.
• Cycle the parking brake ON–OFF–ON.
• Push and hold Volume+ button on the steering wheel. The radio screen will change to FM and will show volume 0. Release the button.
• Screen will show Volume 10 – 20 - 30.
The DSR1 module is now locked to this particular vehicle by VIN number.
Note: If you need to return the radio to its factory non-amplifi ed mode, do this programming procedure and press and hold VOL– button on the steering wheel instead. The radio screen will change to FM and will show volume 0. Release the button. The radio screen will show Volume (30 – 20 - 0). The de-programming sequence is complete.
The DSR1 is now unlocked from the vehicle.
CHIME ADJUSTMENTFront chime
Set Audio source to OFF.
Activate front chime (Ex: door chime).
Adjust using the radio’s volume knob.
Rear chime
Set Audio source to OFF
Activate Rear chime (Ex: Rear parking assist)
Adjust using the radio’s volume knob
TROUBLESHOOTING TIPS:
• To reset the DSR1 module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Wait 15 seconds and re-connect all the connectors back to the module.
For technical assistance :
Call : 1-866-427-2999
E-mail : [email protected]
Visit us at : maestro.idatalink.com/support and www.12voltdata.com/forum/
1
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD TAURUS 2013-2019
Automotive Data Solutions Inc. © 2020 4
1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
WIRING DIAGRAMSTEP 2
STEP 3DSR1 MODULE
RCA CABLES
AFTERMARKET AMPLIFIER
STEP 1
dFO2 T-HARNESS
WHITE (LEFT FRONT)WHITE/BLACK (LEFT FRONT)GRAY (RIGHT FRONT)GRAY/BLACK (RIGHT FRONT)GREEN (LEFT REAR)GREEN/BLACK (LEFT REAR)
PURPLE/BLACK (RIGHT REAR)
(NC) AMP TURN ON
PURPLE (RIGHT REAR)
CONNECT TO OEMRADIO CONNECTOR
CONNECT TO OEMRADIO HARNESS
-
OPTIONAL ACCESSORIES PROGRAMMED FIRMWAREADS-AR-DC-dFO2
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro DSP-FO2 Installation Harness
INSTALL GUIDEFORD TRANSIT
2015-2019ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,
WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD TRANSIT 2015-2019
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD TRANSIT 2015-2019
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory radio and plug the dFO2 T-harness in line with the radio plug.
STEP 2• Connect the wires from the dFO2 T-harness to the
aftermarket amplifi er.
Note 1:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 3• Connect all the harnesses to the DSR1 module.
STEP 4Program the OEM radio to “amplifi ed mode”.
• Close vehicle doors.
• Turn ignition ON-OFF-ON.
• Wait for radio to be completely booted.
• Set the audio source to OFF.
• Cycle the parking brake ON–OFF–ON.
• Push and hold Volume+ button on the steering wheel. The radio screen will change to FM and will show volume 0. Release the button.
• Screen will show Volume 10 – 20 - 30.
The DSR1 module is now locked to this particular vehicle by VIN number.
Note: If you need to return the radio to its factory non-amplifi ed mode, do this programming procedure and press and hold VOL– button on the steering wheel instead. The radio screen will change to FM and will show volume 0. Release the button. The radio screen will show Volume (30 – 20 - 0). The de-programming sequence is complete.
The DSR1 is now unlocked from the vehicle.
CHIME ADJUSTMENTFront chime
Set Audio source to OFF.
Activate front chime (Ex: door chime).
Adjust using the radio’s volume knob.
Rear chime
Set Audio source to OFF
Activate Rear chime (Ex: Rear parking assist)
Adjust using the radio’s volume knob
TROUBLESHOOTING TIPS:
• To reset the DSR1 module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Wait 15 seconds and re-connect all the connectors back to the module.
For technical assistance :
Call : 1-866-427-2999
E-mail : [email protected]
Visit us at : maestro.idatalink.com/support and www.12voltdata.com/forum/
1
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD TRANSIT 2015-2019
Automotive Data Solutions Inc. © 2020 4
1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
WIRING DIAGRAMSTEP 2
STEP 3DSR1 MODULE
RCA CABLES
AFTERMARKET AMPLIFIER
STEP 1
dFO2 T-HARNESS
WHITE (LEFT FRONT)WHITE/BLACK (LEFT FRONT)GRAY (RIGHT FRONT)GRAY/BLACK (RIGHT FRONT)GREEN (LEFT REAR)GREEN/BLACK (LEFT REAR)
PURPLE/BLACK (RIGHT REAR)
(NC) AMP TURN ON
PURPLE (RIGHT REAR)
CONNECT TO OEMRADIO CONNECTOR
CONNECT TO OEMRADIO HARNESS
-
OPTIONAL ACCESSORIES PROGRAMMED FIRMWAREADS-AR-DC-dFO2
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro DSP-FO2 Installation Harness
INSTALL GUIDEFORD TRANSIT CONNECT
2014-2019ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,
WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD TRANSIT CONNECT 2014-2019
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD TRANSIT CONNECT 2014-2019
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory radio and plug the dFO2 T-harness in line with the radio plug.
STEP 2• Connect the wires from the dFO2 T-harness to the
aftermarket amplifi er.
Note 1:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 3• Connect all the harnesses to the DSR1 module.
STEP 4Program the OEM radio to “amplifi ed mode”.
• Close vehicle doors.
• Turn ignition ON-OFF-ON.
• Wait for radio to be completely booted.
• Set the audio source to OFF.
• Cycle the parking brake ON–OFF–ON.
• Push and hold Volume+ button on the steering wheel. The radio screen will change to FM and will show volume 0. Release the button.
• Screen will show Volume 10 – 20 - 30.
The DSR1 module is now locked to this particular vehicle by VIN number.
Note: If you need to return the radio to its factory non-amplifi ed mode, do this programming procedure and press and hold VOL– button on the steering wheel instead. The radio screen will change to FM and will show volume 0. Release the button. The radio screen will show Volume (30 – 20 - 0). The de-programming sequence is complete.
The DSR1 is now unlocked from the vehicle.
CHIME ADJUSTMENTFront chime
Set Audio source to OFF.
Activate front chime (Ex: door chime).
Adjust using the radio’s volume knob.
Rear chime
Set Audio source to OFF
Activate Rear chime (Ex: Rear parking assist)
Adjust using the radio’s volume knob
TROUBLESHOOTING TIPS:
• To reset the DSR1 module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Wait 15 seconds and re-connect all the connectors back to the module.
For technical assistance :
Call : 1-866-427-2999
E-mail : [email protected]
Visit us at : maestro.idatalink.com/support and www.12voltdata.com/forum/
1
-
ADS-DSR1-dFO2-AR-IG-EN maestro.idatalink.com
FORD TRANSIT CONNECT 2014-2019
Automotive Data Solutions Inc. © 2020 4
1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
WIRING DIAGRAMSTEP 2
STEP 3DSR1 MODULE
RCA CABLES
AFTERMARKET AMPLIFIER
STEP 1
dFO2 T-HARNESS
WHITE (LEFT FRONT)WHITE/BLACK (LEFT FRONT)GRAY (RIGHT FRONT)GRAY/BLACK (RIGHT FRONT)GREEN (LEFT REAR)GREEN/BLACK (LEFT REAR)
PURPLE/BLACK (RIGHT REAR)
(NC) AMP TURN ON
PURPLE (RIGHT REAR)
CONNECT TO OEMRADIO CONNECTOR
CONNECT TO OEMRADIO HARNESS
ADS-DSR1-DFO2-ARFord Cmax 2013-2018Table of ContentsInstallation InstructionsWiring Diagram
Ford Edge 2011-2019Table of ContentsInstallation InstructionsWiring Diagram
Ford Escape 2013-2019Table of ContentsInstallation InstructionsWiring Diagram
Ford Expedition 2015-2020Table of ContentsInstallation InstructionsWiring Diagram
Ford Explorer 2011-2019Table of ContentsInstallation InstructionsWiring Diagram
Ford F Super Duty 2017-2019Table of ContentsInstallation InstructionsWiring Diagram
Ford F150 2013-2019Table of ContentsInstallation InstructionsWiring Diagram
Ford Focus 2012-2018Table of ContentsInstallation InstructionsWiring Diagram
Ford Fusion 2013-2019Table of ContentsInstallation InstructionsWiring Diagram
Ford Mustang 2015-2019Table of ContentsInstallation InstructionsWiring Diagram
Ford Taurus 2013-2019Table of ContentsInstallation InstructionsWiring Diagram
Ford Transit 2015-2019Table of ContentsInstallation InstructionsWiring Diagram
Ford Transit Connect 2014-2019Table of ContentsInstallation InstructionsWiring Diagram