how to use this install guidecdncontent2.idatalink.com/corporate/content/manuals/rr... ·...
TRANSCRIPT
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certifi ed technician. Logos and trademarks used here in are the properties of their respective owners.
WARNINGPressing the printer icon or “quick printing” this document will print
all of the guides in this compilation.
Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle.
Print only the pages for your vehicle using the advanced options in the Print menu.
Install your Maestro RR according to the guide for your vehicle.
HOW TO USE THIS INSTALL GUIDE1
2
3
SELECT VEHICLE PRINT PAGES NEEDED
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness
INSTALL GUIDETOyOTA 4 RUNNER
WITh JBL 2014-2016Retains factoRy amplifieR, steeRing wheel contRols, and moRe!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota 4 RunneR with JBl 2014-2016
Automotive Data Solutions Inc. © 2016 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Radio Wire Reference Chart 5
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota 4 RunneR with JBl 2014-2016
Automotive Data Solutions Inc. © 2016 3
INSTALLATION INSTRUCTIONS STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.
• Remove the factory radio.
STEP 2
• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
STEP 3
• Connect the factory harness to the TO2 T-harness.
STEP 4• Plug the male WHITE 2 pin connector of your TO2
T-harness into the OBDII harness.
• Plug the OBDII connector into the OBDII of the vehicle.
STEP 5• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the aftermarket radio (if equipped).
• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).
• Plug the Data cable to the data port of the aftermarket radio.
STEP 6• Connect all the harnesses to the Maestro RR module then
test your installation.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
1
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota 4 RunneR with JBl 2014-2016
Automotive Data Solutions Inc. © 2016 4
AUX INAUX IN
A
G
F
A FG
1
H
H
BACKUP CAMBACKUP CAM
MAINHARNESS
RCA CABLES
RCA CABLES
FACTORY RADIO HARNESS
REVERSE CAMERA HARNESS
TO2 T-HARNESS
STEP 2
STEP 3
STEP 5
WIRES FROMVEHICLE
CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO
CONNECT IF EQUIPPED
CONNECT TOAFTERMARKET RADIO
STEP 6
MAESTRO RR MODULE
DATACABLE
OBDII CONNECTORSTEP 4
WIRING DIAGRAM with an Amplifier
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
YELLOW/BLACK - FOOT BRAKE
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
STEP 1WHITEWHITE/BLACKGRAYGRAY/BLACK
LF RCA INPUT
RF RCA INPUT
SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
CONNECTIONSNOTREQUIREDWITH AMP
YELLOW/GREEN (NOT CONNECTED)YELLOW/GREEN (NOT CONNECTED)
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota 4 RunneR with JBl 2014-2016
Automotive Data Solutions Inc. © 2016 5
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White or Yellow/Green (see Wiring Diagram) Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness
INSTALL GUIDETOyOTA 4 RUNNERWIThOUT JBL 2014-2016
Retains factoRy amplifieR, steeRing wheel contRols, and moRe!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota 4 RunneR without JBl 2014-2016
Automotive Data Solutions Inc. © 2016 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Radio Wire Reference Chart 5
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota 4 RunneR without JBl 2014-2016
Automotive Data Solutions Inc. © 2016 3
INSTALLATION INSTRUCTIONS STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut and remove the front speaker wire junction connectors.
• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.
• Remove the factory radio.
STEP 2
• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
STEP 3
• Connect the factory harness to the TO2 T-harness.
STEP 4• Plug the male WHITE 2 pin connector of your TO2
T-harness into the OBDII harness.
• Plug the OBDII connector into the OBDII of the vehicle.
STEP 5• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the aftermarket radio (if equipped).
• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).
• Plug the Data cable to the data port of the aftermarket radio.
STEP 6• Connect all the harnesses to the Maestro RR module then
test your installation.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
2
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota 4 RunneR without JBl 2014-2016
Automotive Data Solutions Inc. © 2016 4
AUX INAUX IN
A
G
F
A FG
2
H
H
BACKUP CAMBACKUP CAM
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
YELLOW/BLACK - FOOT BRAKE
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
MAINHARNESS
RCA CABLES
FACTORY RADIO HARNESS
REVERSE CAMERA HARNESS
TO2 T-HARNESS
STEP 1
STEP 2
STEP 3
STEP 5
WIRES FROMVEHICLE
CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO
SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
CONNECT TOAFTERMARKET RADIO
STEP 6
MAESTRO RR MODULE
DATACABLE
OBDII CONNECTORSTEP 4
CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)
WIRING DIAGRAM without an Amplifier
CONNECT IF EQUIPPED
YELLOW/GREEN (NOT CONNECTED)YELLOW/GREEN (NOT CONNECTED)
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota 4 RunneR without JBl 2014-2016
Automotive Data Solutions Inc. © 2016 5
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White or Yellow/Green (see Wiring Diagram) Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness
INSTALL GUIDETOyOTA AvALONWITh JBL 2015-2016
Retains factoRy amplifieR, steeRing wheel contRols, and moRe!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota avalon with JBl 2015-2016
Automotive Data Solutions Inc. © 2016 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Radio Wire Reference Chart 5
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota avalon with JBl 2015-2016
Automotive Data Solutions Inc. © 2016 3
INSTALLATION INSTRUCTIONS STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.
• Remove the factory radio.
STEP 2
• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
STEP 3
• Connect the factory harness to the TO2 T-harness.
STEP 4• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the aftermarket radio (if equipped).
• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).
• Plug the Data cable to the data port of the aftermarket radio.
STEP 5• Connect all the harnesses to the Maestro RR module then
test your installation.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
3
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota avalon with JBl 2015-2016
Automotive Data Solutions Inc. © 2016 4
AUX INAUX IN
A
G
F
A FG
3
H
H
BACKUP CAMBACKUP CAM
NOT CONNECTED
MAINHARNESS
RCA CABLES
RCA CABLES
FACTORY RADIO HARNESS
REVERSE CAMERA HARNESS
TO2 T-HARNESS
STEP 2
STEP 3
STEP 4
WIRES FROMVEHICLE
CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO
CONNECT TOAFTERMARKET RADIO
STEP 5
MAESTRO RR MODULE
DATACABLE
WIRING DIAGRAM with an Amplifier
CONNECTION NOT REQUIRED
CONNECT IF EQUIPPED
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
YELLOW/BLACK - FOOT BRAKE
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
WHITEWHITE/BLACKGRAYGRAY/BLACK
LF RCA INPUT
RF RCA INPUT
SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
CONNECTIONSNOTREQUIREDWITH AMP
STEP 1
YELLOW/GREEN (NOT CONNECTED)YELLOW/GREEN (NOT CONNECTED)
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota avalon with JBl 2015-2016
Automotive Data Solutions Inc. © 2016 5
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White or Yellow/Green (see Wiring Diagram) Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness
INSTALL GUIDETOyOTA AvALON
WIThOUT JBL 2015-2016Retains factoRy amplifieR, steeRing wheel contRols, and moRe!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota avalon without JBl 2015-2016
Automotive Data Solutions Inc. © 2016 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Radio Wire Reference Chart 5
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota avalon without JBl 2015-2016
Automotive Data Solutions Inc. © 2016 3
INSTALLATION INSTRUCTIONS STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut and remove the front speaker wire junction connectors.
• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.
• Remove the factory radio.
STEP 2
• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
STEP 3
• Connect the factory harness to the TO2 T-harness.
STEP 4• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the aftermarket radio (if equipped).
• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).
• Plug the Data cable to the data port of the aftermarket radio.
STEP 5• Connect all the harnesses to the Maestro RR module then
test your installation.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
4
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota avalon without JBl 2015-2016
Automotive Data Solutions Inc. © 2016 4
AUX INAUX IN
A
G
F
A FG
4
H
H
BACKUP CAMBACKUP CAM
NOT CONNECTED
CONNECTION NOT REQUIRED
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
YELLOW/BLACK - FOOT BRAKE
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
MAINHARNESS
RCA CABLES
FACTORY RADIO HARNESS
REVERSE CAMERA HARNESS
TO2 T-HARNESS
STEP 1
STEP 2
STEP 3
STEP 4
WIRES FROMVEHICLE
CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO
SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
CONNECT TOAFTERMARKET RADIO
STEP 5
MAESTRO RR MODULE
DATACABLE
CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)
WIRING DIAGRAM without an Amplifier
CONNECT IF EQUIPPED
YELLOW/GREEN (NOT CONNECTED)YELLOW/GREEN (NOT CONNECTED)
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota avalon without JBl 2015-2016
Automotive Data Solutions Inc. © 2016 5
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White or Yellow/Green (see Wiring Diagram) Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness
INSTALL GUIDETOyOTA CAMRy
WITh FACTORy 6.1" SCREEN 2012-2014Retains factoRy amplifieR, steeRing wheel contRols, and moRe!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota camRy with factoRy 6.1" scReen 2012-2014
Automotive Data Solutions Inc. © 2016 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Radio Wire Reference Chart 5
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota camRy with factoRy 6.1" scReen 2012-2014
Automotive Data Solutions Inc. © 2016 3
INSTALLATION INSTRUCTIONS STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut and remove the front speaker wire junction connectors.
• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.
• Remove the factory radio.
STEP 2
• If the vehicle is equipped with an OEM backup camera: Cut the reverse camera plug of the TO2 T-harness and connect the wires as indicated in the wiring diagram next page (BROWN/RED and BROWN/YELLOW wires are not used).
STEP 3
• Connect the factory harness to the TO2 T-harness.
STEP 4• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the aftermarket radio (if equipped).
• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).
• Plug the Data cable to the data port of the aftermarket radio.
STEP 5• Connect all the harnesses to the Maestro RR module then
test your installation.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
5
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota camRy with factoRy 6.1" scReen 2012-2014
Automotive Data Solutions Inc. © 2016 4
23 1456789101213 11141516
AUX INAUX IN
A
G
F
A FG
5
H
H
BACKUP CAMBACKUP CAM
NOT CONNECTED
CONNECTION NOT REQUIRED
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
YELLOW/BLACK - FOOT BRAKE
YELLOW WHITERED
BLACK
BLACK
BLUE/YELLOWBLACK
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
MAINHARNESS
RCA CABLES
FACTORY RADIO HARNESS
REVERSE CAMERA HARNESS
TO2 T-HARNESS
STEP 1
STEP 2
STEP 3
STEP 4
WIRES FROMVEHICLE
CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO
SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
CONNECT TOAFTERMARKET RADIO
STEP 5
MAESTRO RR MODULE
DATACABLE
CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)
WIRING DIAGRAM without an Amplifier
CONNECT IF EQUIPPEDCUT REVERSECAMERACONNECTOR FROMTO2 T-HARNESSAND CONNECTWIRES AS SHOWN.
YELLOW/GREEN (NOT CONNECTED)YELLOW/GREEN (NOT CONNECTED)
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota camRy with factoRy 6.1" scReen 2012-2014
Automotive Data Solutions Inc. © 2016 5
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White or Yellow/Green (see Wiring Diagram) Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness
INSTALL GUIDETOyOTA CAMRy
WITh FACTORy 6.1" SCREEN AND JBL 2012-2014
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota camRy with factoRy 6.1" scReen and JBl 2012-2014
Automotive Data Solutions Inc. © 2016 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Radio Wire Reference Chart 5
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota camRy with factoRy 6.1" scReen and JBl 2012-2014
Automotive Data Solutions Inc. © 2016 3
INSTALLATION INSTRUCTIONS STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.
• Remove the factory radio.
STEP 2
• If the vehicle is equipped with an OEM backup camera: Cut the reverse camera plug of the TO2 T-harness and connect the wires as indicated in the wiring diagram next page (BROWN/RED and BROWN/YELLOW wires are not used).
STEP 3
• Connect the factory harness to the TO2 T-harness.
STEP 4• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the aftermarket radio (if equipped).
• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).
• Plug the Data cable to the data port of the aftermarket radio.
STEP 5• Connect all the harnesses to the Maestro RR module then
test your installation.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
6
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota camRy with factoRy 6.1" scReen and JBl 2012-2014
Automotive Data Solutions Inc. © 2016 4
AUX INAUX IN
23 1456789101213 11141516
A
G
F
A FG
6
H
H
BACKUP CAMBACKUP CAM
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
YELLOW/BLACK - FOOT BRAKE
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
MAINHARNESS
RCA CABLES
RCA CABLES
STEP 1 STEP 4WHITEWHITE/BLACKGRAYGRAY/BLACK
LF RCA INPUT
RF RCA INPUT
CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO
SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
CONNECT TOAFTERMARKET RADIO
WIRING DIAGRAM with an Amplifier
CONNECTIONSNOTREQUIREDWITH AMP
NOT CONNECTED
CONNECTION NOT REQUIRED
YELLOW WHITERED
BLACK
BLACK
BLUE/YELLOWBLACK
FACTORY RADIO HARNESS
REVERSE CAMERA HARNESS
TO2 T-HARNESS
STEP 2
STEP 3
WIRES FROMVEHICLE
STEP 5
MAESTRO RR MODULE
DATACABLECUT REVERSE
CAMERACONNECTOR FROMTO2 T-HARNESSAND CONNECTWIRES AS SHOWN.
CONNECT IF EQUIPPED
YELLOW/GREEN (NOT CONNECTED)YELLOW/GREEN (NOT CONNECTED)YELLOW/GREEN (NOT CONNECTED)YELLOW/GREEN (NOT CONNECTED)
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota camRy with factoRy 6.1" scReen and JBl 2012-2014
Automotive Data Solutions Inc. © 2016 5
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White or Yellow/Green (see Wiring Diagram) Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness
INSTALL GUIDETOyOTA CAMRy
WITh FACTORy SCREEN & hDD & JBL 2012-2014
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota camRy with factoRy scReen & hdd & JBl 2012-2014
Automotive Data Solutions Inc. © 2016 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Radio Wire Reference Chart 5
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota camRy with factoRy scReen & hdd & JBl 2012-2014
Automotive Data Solutions Inc. © 2016 3
INSTALLATION INSTRUCTIONS STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.
• Remove the factory radio.
STEP 2
• If the vehicle is equipped with an OEM backup camera: Cut the reverse camera plug of the TO2 T-harness and connect the wires as indicated in the wiring diagram next page (BROWN/RED and BROWN/YELLOW wires are not used).
STEP 3
• Connect the factory harness to the TO2 T-harness.
STEP 4• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the aftermarket radio (if equipped).
• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).
• Plug the Data cable to the data port of the aftermarket radio.
STEP 5• Connect all the harnesses to the Maestro RR module then
test your installation.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
6
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota camRy with factoRy scReen & hdd & JBl 2012-2014
Automotive Data Solutions Inc. © 2016 4
AUX INAUX IN
23 1456789101213 11141516
A
G
F
A FG
6
H
H
BACKUP CAMBACKUP CAM
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
YELLOW/BLACK - FOOT BRAKE
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
MAINHARNESS
RCA CABLES
RCA CABLES
STEP 1 STEP 4WHITEWHITE/BLACKGRAYGRAY/BLACK
LF RCA INPUT
RF RCA INPUT
CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO
SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
CONNECT TOAFTERMARKET RADIO
WIRING DIAGRAM with an Amplifier
CONNECTIONSNOTREQUIREDWITH AMP
NOT CONNECTED
CONNECTION NOT REQUIRED
YELLOW WHITERED
BLACK
BLACK
BLUE/YELLOWBLACK
FACTORY RADIO HARNESS
REVERSE CAMERA HARNESS
TO2 T-HARNESS
STEP 2
STEP 3
WIRES FROMVEHICLE
STEP 5
MAESTRO RR MODULE
DATACABLECUT REVERSE
CAMERACONNECTOR FROMTO2 T-HARNESSAND CONNECTWIRES AS SHOWN.
CONNECT IF EQUIPPED
YELLOW/GREEN (NOT CONNECTED)YELLOW/GREEN (NOT CONNECTED)YELLOW/GREEN (NOT CONNECTED)YELLOW/GREEN (NOT CONNECTED)
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota camRy with factoRy scReen & hdd & JBl 2012-2014
Automotive Data Solutions Inc. © 2016 5
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White or Yellow/Green (see Wiring Diagram) Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness
INSTALL GUIDETOyOTA CAMRyWITh JBL 2015-2016
Retains factoRy amplifieR, steeRing wheel contRols, and moRe!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota camRy with JBl 2015-2016
Automotive Data Solutions Inc. © 2016 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Radio Wire Reference Chart 5
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota camRy with JBl 2015-2016
Automotive Data Solutions Inc. © 2016 3
INSTALLATION INSTRUCTIONS STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.
• Remove the factory radio.
STEP 2
• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
STEP 3
• Connect the factory harness to the TO2 T-harness.
STEP 4• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the aftermarket radio (if equipped).
• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).
• Plug the Data cable to the data port of the aftermarket radio.
STEP 5• Connect all the harnesses to the Maestro RR module then
test your installation.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
3
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota camRy with JBl 2015-2016
Automotive Data Solutions Inc. © 2016 4
AUX INAUX IN
A
G
F
A FG
3
H
H
BACKUP CAMBACKUP CAM
NOT CONNECTED
MAINHARNESS
RCA CABLES
RCA CABLES
FACTORY RADIO HARNESS
REVERSE CAMERA HARNESS
TO2 T-HARNESS
STEP 2
STEP 3
STEP 4
WIRES FROMVEHICLE
CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO
CONNECT TOAFTERMARKET RADIO
STEP 5
MAESTRO RR MODULE
DATACABLE
WIRING DIAGRAM with an Amplifier
CONNECTION NOT REQUIRED
CONNECT IF EQUIPPED
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
YELLOW/BLACK - FOOT BRAKE
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
WHITEWHITE/BLACKGRAYGRAY/BLACK
LF RCA INPUT
RF RCA INPUT
SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
CONNECTIONSNOTREQUIREDWITH AMP
STEP 1
YELLOW/GREEN (NOT CONNECTED)YELLOW/GREEN (NOT CONNECTED)
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota camRy with JBl 2015-2016
Automotive Data Solutions Inc. © 2016 5
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White or Yellow/Green (see Wiring Diagram) Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness
INSTALL GUIDETOyOTA CAMRy
WIThOUT JBL 2015-2016Retains factoRy amplifieR, steeRing wheel contRols, and moRe!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota camRy without JBl 2015-2016
Automotive Data Solutions Inc. © 2016 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Radio Wire Reference Chart 5
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota camRy without JBl 2015-2016
Automotive Data Solutions Inc. © 2016 3
INSTALLATION INSTRUCTIONS STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut and remove the front speaker wire junction connectors.
• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.
• Remove the factory radio.
STEP 2
• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
STEP 3
• Connect the factory harness to the TO2 T-harness.
STEP 4• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the aftermarket radio (if equipped).
• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).
• Plug the Data cable to the data port of the aftermarket radio.
STEP 5• Connect all the harnesses to the Maestro RR module then
test your installation.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
4
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota camRy without JBl 2015-2016
Automotive Data Solutions Inc. © 2016 4
AUX INAUX IN
A
G
F
A FG
4
H
H
BACKUP CAMBACKUP CAM
NOT CONNECTED
CONNECTION NOT REQUIRED
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
YELLOW/BLACK - FOOT BRAKE
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
MAINHARNESS
RCA CABLES
FACTORY RADIO HARNESS
REVERSE CAMERA HARNESS
TO2 T-HARNESS
STEP 1
STEP 2
STEP 3
STEP 4
WIRES FROMVEHICLE
CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO
SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
CONNECT TOAFTERMARKET RADIO
STEP 5
MAESTRO RR MODULE
DATACABLE
CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)
WIRING DIAGRAM without an Amplifier
CONNECT IF EQUIPPED
YELLOW/GREEN (NOT CONNECTED)YELLOW/GREEN (NOT CONNECTED)
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota camRy without JBl 2015-2016
Automotive Data Solutions Inc. © 2016 5
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White or Yellow/Green (see Wiring Diagram) Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness
INSTALL GUIDETOyOTA COROLLA
WITh FACTORy 6.1" SCREEN 2014-2016Retains factoRy amplifieR, steeRing wheel contRols, and moRe!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota coRolla with factoRy 6.1" scReen 2014-2016
Automotive Data Solutions Inc. © 2016 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Radio Wire Reference Chart 5
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota coRolla with factoRy 6.1" scReen 2014-2016
Automotive Data Solutions Inc. © 2016 3
INSTALLATION INSTRUCTIONS STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut and remove the front speaker wire junction connectors.
• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.
• Remove the factory radio.
STEP 2
• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
STEP 3
• Connect the factory harness to the TO2 T-harness.
STEP 4• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the aftermarket radio (if equipped).
• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).
• Plug the Data cable to the data port of the aftermarket radio.
STEP 5• Connect all the harnesses to the Maestro RR module then
test your installation.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
4
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota coRolla with factoRy 6.1" scReen 2014-2016
Automotive Data Solutions Inc. © 2016 4
AUX INAUX IN
A
G
F
A FG
4
H
H
BACKUP CAMBACKUP CAM
NOT CONNECTED
CONNECTION NOT REQUIRED
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
YELLOW/BLACK - FOOT BRAKE
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
MAINHARNESS
RCA CABLES
FACTORY RADIO HARNESS
REVERSE CAMERA HARNESS
TO2 T-HARNESS
STEP 1
STEP 2
STEP 3
STEP 4
WIRES FROMVEHICLE
CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO
SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
CONNECT TOAFTERMARKET RADIO
STEP 5
MAESTRO RR MODULE
DATACABLE
CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)
WIRING DIAGRAM without an Amplifier
CONNECT IF EQUIPPED
YELLOW/GREEN (NOT CONNECTED)YELLOW/GREEN (NOT CONNECTED)
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota coRolla with factoRy 6.1" scReen 2014-2016
Automotive Data Solutions Inc. © 2016 5
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White or Yellow/Green (see Wiring Diagram) Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness
INSTALL GUIDETOyOTA hIGhLANDER
WITh JBL 2014-2016Retains factoRy amplifieR, steeRing wheel contRols, and moRe!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota highlandeR with JBl 2014-2016
Automotive Data Solutions Inc. © 2016 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Radio Wire Reference Chart 5
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota highlandeR with JBl 2014-2016
Automotive Data Solutions Inc. © 2016 3
INSTALLATION INSTRUCTIONS STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.
• Remove the factory radio.
STEP 2
• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
STEP 3
• Connect the factory harness to the TO2 T-harness.
STEP 4• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the aftermarket radio (if equipped).
• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).
• Plug the Data cable to the data port of the aftermarket radio.
STEP 5• Connect all the harnesses to the Maestro RR module then
test your installation.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
3
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota highlandeR with JBl 2014-2016
Automotive Data Solutions Inc. © 2016 4
AUX INAUX IN
A
G
F
A FG
3
H
H
BACKUP CAMBACKUP CAM
NOT CONNECTED
MAINHARNESS
RCA CABLES
RCA CABLES
FACTORY RADIO HARNESS
REVERSE CAMERA HARNESS
TO2 T-HARNESS
STEP 2
STEP 3
STEP 4
WIRES FROMVEHICLE
CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO
CONNECT TOAFTERMARKET RADIO
STEP 5
MAESTRO RR MODULE
DATACABLE
WIRING DIAGRAM with an Amplifier
CONNECTION NOT REQUIRED
CONNECT IF EQUIPPED
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
YELLOW/BLACK - FOOT BRAKE
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
WHITEWHITE/BLACKGRAYGRAY/BLACK
LF RCA INPUT
RF RCA INPUT
SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
CONNECTIONSNOTREQUIREDWITH AMP
STEP 1
YELLOW/GREEN (NOT CONNECTED)YELLOW/GREEN (NOT CONNECTED)
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota highlandeR with JBl 2014-2016
Automotive Data Solutions Inc. © 2016 5
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White or Yellow/Green (see Wiring Diagram) Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness
INSTALL GUIDETOyOTA hIGhLANDER
WIThOUT JBL 2014-2016Retains factoRy amplifieR, steeRing wheel contRols, and moRe!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota highlandeR without JBl 2014-2016
Automotive Data Solutions Inc. © 2016 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Radio Wire Reference Chart 5
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota highlandeR without JBl 2014-2016
Automotive Data Solutions Inc. © 2016 3
INSTALLATION INSTRUCTIONS STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut and remove the front speaker wire junction connectors.
• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.
• Remove the factory radio.
STEP 2
• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
STEP 3
• Connect the factory harness to the TO2 T-harness.
STEP 4• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the aftermarket radio (if equipped).
• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).
• Plug the Data cable to the data port of the aftermarket radio.
STEP 5• Connect all the harnesses to the Maestro RR module then
test your installation.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
4
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota highlandeR without JBl 2014-2016
Automotive Data Solutions Inc. © 2016 4
AUX INAUX IN
A
G
F
A FG
4
H
H
BACKUP CAMBACKUP CAM
NOT CONNECTED
CONNECTION NOT REQUIRED
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
YELLOW/BLACK - FOOT BRAKE
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
MAINHARNESS
RCA CABLES
FACTORY RADIO HARNESS
REVERSE CAMERA HARNESS
TO2 T-HARNESS
STEP 1
STEP 2
STEP 3
STEP 4
WIRES FROMVEHICLE
CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO
SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
CONNECT TOAFTERMARKET RADIO
STEP 5
MAESTRO RR MODULE
DATACABLE
CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)
WIRING DIAGRAM without an Amplifier
CONNECT IF EQUIPPED
YELLOW/GREEN (NOT CONNECTED)YELLOW/GREEN (NOT CONNECTED)
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota highlandeR without JBl 2014-2016
Automotive Data Solutions Inc. © 2016 5
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White or Yellow/Green (see Wiring Diagram) Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness
INSTALL GUIDETOyOTA RAv 4
WITh FACTORy 6.1" SCREEN 2013-2016Retains factoRy amplifieR, steeRing wheel contRols, and moRe!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota Rav 4 with factoRy 6.1" scReen 2013-2016
Automotive Data Solutions Inc. © 2016 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Radio Wire Reference Chart 5
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota Rav 4 with factoRy 6.1" scReen 2013-2016
Automotive Data Solutions Inc. © 2016 3
INSTALLATION INSTRUCTIONS STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut and remove the front speaker wire junction connectors.
• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.
• Remove the factory radio.
STEP 2
• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
STEP 3
• Connect the factory harness to the TO2 T-harness.
STEP 4• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the aftermarket radio (if equipped).
• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).
• Plug the Data cable to the data port of the aftermarket radio.
STEP 5• Connect all the harnesses to the Maestro RR module then
test your installation.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
4
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota Rav 4 with factoRy 6.1" scReen 2013-2016
Automotive Data Solutions Inc. © 2016 4
AUX INAUX IN
A
G
F
A FG
4
H
H
BACKUP CAMBACKUP CAM
NOT CONNECTED
CONNECTION NOT REQUIRED
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
YELLOW/BLACK - FOOT BRAKE
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
MAINHARNESS
RCA CABLES
FACTORY RADIO HARNESS
REVERSE CAMERA HARNESS
TO2 T-HARNESS
STEP 1
STEP 2
STEP 3
STEP 4
WIRES FROMVEHICLE
CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO
SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
CONNECT TOAFTERMARKET RADIO
STEP 5
MAESTRO RR MODULE
DATACABLE
CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)
WIRING DIAGRAM without an Amplifier
CONNECT IF EQUIPPED
YELLOW/GREEN (NOT CONNECTED)YELLOW/GREEN (NOT CONNECTED)
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota Rav 4 with factoRy 6.1" scReen 2013-2016
Automotive Data Solutions Inc. © 2016 5
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White or Yellow/Green (see Wiring Diagram) Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness
INSTALL GUIDETOyOTA RAv 4
WITh FACTORy 6.1" SCREEN AND JBL 2013-2016
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota Rav 4 with factoRy 6.1" scReen and JBl 2013-2016
Automotive Data Solutions Inc. © 2016 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Radio Wire Reference Chart 5
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota Rav 4 with factoRy 6.1" scReen and JBl 2013-2016
Automotive Data Solutions Inc. © 2016 3
INSTALLATION INSTRUCTIONS STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.
• Remove the factory radio.
STEP 2
• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
STEP 3
• Connect the factory harness to the TO2 T-harness.
STEP 4• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the aftermarket radio (if equipped).
• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).
• Plug the Data cable to the data port of the aftermarket radio.
STEP 5• Connect all the harnesses to the Maestro RR module then
test your installation.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
3
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota Rav 4 with factoRy 6.1" scReen and JBl 2013-2016
Automotive Data Solutions Inc. © 2016 4
AUX INAUX IN
A
G
F
A FG
3
H
H
BACKUP CAMBACKUP CAM
NOT CONNECTED
MAINHARNESS
RCA CABLES
RCA CABLES
FACTORY RADIO HARNESS
REVERSE CAMERA HARNESS
TO2 T-HARNESS
STEP 2
STEP 3
STEP 4
WIRES FROMVEHICLE
CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO
CONNECT TOAFTERMARKET RADIO
STEP 5
MAESTRO RR MODULE
DATACABLE
WIRING DIAGRAM with an Amplifier
CONNECTION NOT REQUIRED
CONNECT IF EQUIPPED
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
YELLOW/BLACK - FOOT BRAKE
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
WHITEWHITE/BLACKGRAYGRAY/BLACK
LF RCA INPUT
RF RCA INPUT
SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
CONNECTIONSNOTREQUIREDWITH AMP
STEP 1
YELLOW/GREEN (NOT CONNECTED)YELLOW/GREEN (NOT CONNECTED)
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota Rav 4 with factoRy 6.1" scReen and JBl 2013-2016
Automotive Data Solutions Inc. © 2016 5
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White or Yellow/Green (see Wiring Diagram) Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness
INSTALL GUIDETOyOTA SIENNAWITh JBL 2015-2016
Retains factoRy amplifieR, steeRing wheel contRols, and moRe!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota sienna with JBl 2015-2016
Automotive Data Solutions Inc. © 2016 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Radio Wire Reference Chart 5
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota sienna with JBl 2015-2016
Automotive Data Solutions Inc. © 2016 3
INSTALLATION INSTRUCTIONS STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.
• Remove the factory radio.
STEP 2
• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
Note: The reverse camera cannot be retained in this vehicle.
STEP 3
• Connect the factory harness to the TO2 T-harness.
STEP 4• Plug the male WHITE 2 pin connector of your TO2
T-harness into the OBDII harness.
• Plug the OBDII connector into the OBDII of the vehicle.
STEP 5• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).
• Plug the Data cable to the data port of the aftermarket radio.
STEP 6• Connect all the harnesses to the Maestro RR module then
test your installation.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
7
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota sienna with JBl 2015-2016
Automotive Data Solutions Inc. © 2016 4
AUX INAUX IN
A
G
F
A FG
7
H
H
BACKUP CAMBACKUP CAM
REVERSE CAMERA HARNESSSTEP 2CONNECT IF EQUIPPED
MAINHARNESS
RCA CABLES
RCA CABLES
FACTORY RADIO HARNESS
TO2 T-HARNESS
STEP 3
STEP 5
WIRES FROMVEHICLE
CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO
CONNECTION NOT REQUIREDREVERSE CAMERA CANNOTBE RETAINED
CONNECT TOAFTERMARKET RADIO
STEP 6
MAESTRO RR MODULE
DATACABLE
OBDII CONNECTORSTEP 4
WIRING DIAGRAM with an Amplifier
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
YELLOW/BLACK - FOOT BRAKE
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
STEP 1WHITEWHITE/BLACKGRAYGRAY/BLACK
LF RCA INPUT
RF RCA INPUT
SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
CONNECTIONSNOTREQUIREDWITH AMP
YELLOW/GREEN (NOT CONNECTED)YELLOW/GREEN (NOT CONNECTED)YELLOW/GREEN (NOT CONNECTED)
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota sienna with JBl 2015-2016
Automotive Data Solutions Inc. © 2016 5
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White or Yellow/Green (see Wiring Diagram) Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness
INSTALL GUIDETOyOTA SIENNA
WIThOUT JBL 2015-2016Retains factoRy amplifieR, steeRing wheel contRols, and moRe!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota sienna without JBl 2015-2016
Automotive Data Solutions Inc. © 2016 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Radio Wire Reference Chart 5
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota sienna without JBl 2015-2016
Automotive Data Solutions Inc. © 2016 3
INSTALLATION INSTRUCTIONS STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut and remove the front speaker wire junction connectors.
• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.
• Remove the factory radio.
STEP 2
• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
STEP 3
• Connect the factory harness to the TO2 T-harness.
STEP 4• Plug the male WHITE 2 pin connector of your TO2
T-harness into the OBDII harness.
• Plug the OBDII connector into the OBDII of the vehicle.
STEP 5• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the aftermarket radio (if equipped).
• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).
• Plug the Data cable to the data port of the aftermarket radio.
STEP 6• Connect all the harnesses to the Maestro RR module then
test your installation.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
2
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota sienna without JBl 2015-2016
Automotive Data Solutions Inc. © 2016 4
AUX INAUX IN
A
G
F
A FG
2
H
H
BACKUP CAMBACKUP CAM
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
YELLOW/BLACK - FOOT BRAKE
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
MAINHARNESS
RCA CABLES
FACTORY RADIO HARNESS
REVERSE CAMERA HARNESS
TO2 T-HARNESS
STEP 1
STEP 2
STEP 3
STEP 5
WIRES FROMVEHICLE
CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO
SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
CONNECT TOAFTERMARKET RADIO
STEP 6
MAESTRO RR MODULE
DATACABLE
OBDII CONNECTORSTEP 4
CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)
WIRING DIAGRAM without an Amplifier
CONNECT IF EQUIPPED
YELLOW/GREEN (NOT CONNECTED)YELLOW/GREEN (NOT CONNECTED)
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota sienna without JBl 2015-2016
Automotive Data Solutions Inc. © 2016 5
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White or Yellow/Green (see Wiring Diagram) Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness
INSTALL GUIDETOyOTA TACOMA
WITh JBL 2016Retains factoRy amplifieR, steeRing wheel contRols, and moRe!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota tacoma with JBl 2016
Automotive Data Solutions Inc. © 2016 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Radio Wire Reference Chart 5
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota tacoma with JBl 2016
Automotive Data Solutions Inc. © 2016 3
INSTALLATION INSTRUCTIONS STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.
• Remove the factory radio.
STEP 2
• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
STEP 3
• Connect the factory harness to the TO2 T-harness.
STEP 4• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the aftermarket radio (if equipped).
• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).
• Plug the Data cable to the data port of the aftermarket radio.
STEP 5• Connect all the harnesses to the Maestro RR module then
test your installation.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
3
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota tacoma with JBl 2016
Automotive Data Solutions Inc. © 2016 4
AUX INAUX IN
A
G
F
A FG
3
H
H
BACKUP CAMBACKUP CAM
NOT CONNECTED
MAINHARNESS
RCA CABLES
RCA CABLES
FACTORY RADIO HARNESS
REVERSE CAMERA HARNESS
TO2 T-HARNESS
STEP 2
STEP 3
STEP 4
WIRES FROMVEHICLE
CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO
CONNECT TOAFTERMARKET RADIO
STEP 5
MAESTRO RR MODULE
DATACABLE
WIRING DIAGRAM with an Amplifier
CONNECTION NOT REQUIRED
CONNECT IF EQUIPPED
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
YELLOW/BLACK - FOOT BRAKE
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
WHITEWHITE/BLACKGRAYGRAY/BLACK
LF RCA INPUT
RF RCA INPUT
SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
CONNECTIONSNOTREQUIREDWITH AMP
STEP 1
YELLOW/GREEN (NOT CONNECTED)YELLOW/GREEN (NOT CONNECTED)
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota tacoma with JBl 2016
Automotive Data Solutions Inc. © 2016 5
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White or Yellow/Green (see Wiring Diagram) Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness
INSTALL GUIDETOyOTA TACOMA
WIThOUT JBL 2016Retains factoRy amplifieR, steeRing wheel contRols, and moRe!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota tacoma without JBl 2016
Automotive Data Solutions Inc. © 2016 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Radio Wire Reference Chart 5
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota tacoma without JBl 2016
Automotive Data Solutions Inc. © 2016 3
INSTALLATION INSTRUCTIONS STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut and remove the front speaker wire junction connectors.
• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.
• Remove the factory radio.
STEP 2
• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
STEP 3
• Connect the factory harness to the TO2 T-harness.
STEP 4• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the aftermarket radio (if equipped).
• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).
• Plug the Data cable to the data port of the aftermarket radio.
STEP 5• Connect all the harnesses to the Maestro RR module then
test your installation.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
4
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota tacoma without JBl 2016
Automotive Data Solutions Inc. © 2016 4
AUX INAUX IN
A
G
F
A FG
4
H
H
BACKUP CAMBACKUP CAM
NOT CONNECTED
CONNECTION NOT REQUIRED
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
YELLOW/BLACK - FOOT BRAKE
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
MAINHARNESS
RCA CABLES
FACTORY RADIO HARNESS
REVERSE CAMERA HARNESS
TO2 T-HARNESS
STEP 1
STEP 2
STEP 3
STEP 4
WIRES FROMVEHICLE
CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO
SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
CONNECT TOAFTERMARKET RADIO
STEP 5
MAESTRO RR MODULE
DATACABLE
CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)
WIRING DIAGRAM without an Amplifier
CONNECT IF EQUIPPED
YELLOW/GREEN (NOT CONNECTED)YELLOW/GREEN (NOT CONNECTED)
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota tacoma without JBl 2016
Automotive Data Solutions Inc. © 2016 5
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White or Yellow/Green (see Wiring Diagram) Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness
INSTALL GUIDETOyOTA TUNDRAWITh JBL 2014-2016
Retains factoRy amplifieR, steeRing wheel contRols, and moRe!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota tundRa with JBl 2014-2016
Automotive Data Solutions Inc. © 2016 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Radio Wire Reference Chart 5
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota tundRa with JBl 2014-2016
Automotive Data Solutions Inc. © 2016 3
INSTALLATION INSTRUCTIONS STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.
• Remove the factory radio.
STEP 2
• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
STEP 3
• Connect the factory harness to the TO2 T-harness.
STEP 4• Plug the male WHITE 2 pin connector of your TO2
T-harness into the OBDII harness.
• Plug the OBDII connector into the OBDII of the vehicle.
STEP 5• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the aftermarket radio (if equipped).
• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).
• Plug the Data cable to the data port of the aftermarket radio.
STEP 6• Connect all the harnesses to the Maestro RR module then
test your installation.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
1
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota tundRa with JBl 2014-2016
Automotive Data Solutions Inc. © 2016 4
AUX INAUX IN
A
G
F
A FG
1
H
H
BACKUP CAMBACKUP CAM
MAINHARNESS
RCA CABLES
RCA CABLES
FACTORY RADIO HARNESS
REVERSE CAMERA HARNESS
TO2 T-HARNESS
STEP 2
STEP 3
STEP 5
WIRES FROMVEHICLE
CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO
CONNECT IF EQUIPPED
CONNECT TOAFTERMARKET RADIO
STEP 6
MAESTRO RR MODULE
DATACABLE
OBDII CONNECTORSTEP 4
WIRING DIAGRAM with an Amplifier
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
YELLOW/BLACK - FOOT BRAKE
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
STEP 1WHITEWHITE/BLACKGRAYGRAY/BLACK
LF RCA INPUT
RF RCA INPUT
SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
CONNECTIONSNOTREQUIREDWITH AMP
YELLOW/GREEN (NOT CONNECTED)YELLOW/GREEN (NOT CONNECTED)
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota tundRa with JBl 2014-2016
Automotive Data Solutions Inc. © 2016 5
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White or Yellow/Green (see Wiring Diagram) Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness
INSTALL GUIDETOyOTA TUNDRA
WIThOUT JBL 2014-2016Retains factoRy amplifieR, steeRing wheel contRols, and moRe!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota tundRa without JBl 2014-2016
Automotive Data Solutions Inc. © 2016 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Radio Wire Reference Chart 5
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota tundRa without JBl 2014-2016
Automotive Data Solutions Inc. © 2016 3
INSTALLATION INSTRUCTIONS STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Cut and remove the front speaker wire junction connectors.
• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.
• Remove the factory radio.
STEP 2
• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
STEP 3
• Connect the factory harness to the TO2 T-harness.
STEP 4• Plug the male WHITE 2 pin connector of your TO2
T-harness into the OBDII harness.
• Plug the OBDII connector into the OBDII of the vehicle.
STEP 5• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the aftermarket radio (if equipped).
• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).
• Plug the Data cable to the data port of the aftermarket radio.
STEP 6• Connect all the harnesses to the Maestro RR module then
test your installation.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
2
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota tundRa without JBl 2014-2016
Automotive Data Solutions Inc. © 2016 4
AUX INAUX IN
A
G
F
A FG
2
H
H
BACKUP CAMBACKUP CAM
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
YELLOW/BLACK - FOOT BRAKE
ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)
PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
MAINHARNESS
RCA CABLES
FACTORY RADIO HARNESS
REVERSE CAMERA HARNESS
TO2 T-HARNESS
STEP 1
STEP 2
STEP 3
STEP 5
WIRES FROMVEHICLE
CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO
SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
CONNECT TOAFTERMARKET RADIO
STEP 6
MAESTRO RR MODULE
DATACABLE
OBDII CONNECTORSTEP 4
CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)
WIRING DIAGRAM without an Amplifier
CONNECT IF EQUIPPED
YELLOW/GREEN (NOT CONNECTED)YELLOW/GREEN (NOT CONNECTED)
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota tundRa without JBl 2014-2016
Automotive Data Solutions Inc. © 2016 5
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White or Yellow/Green (see Wiring Diagram) Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness
INSTALL GUIDETOyOTA vENzA
WITh JBL 2015-2016Retains factoRy amplifieR, steeRing wheel contRols, and moRe!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota venza with JBl 2015-2016
Automotive Data Solutions Inc. © 2016 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Radio Wire Reference Chart 5
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota venza with JBl 2015-2016
Automotive Data Solutions Inc. © 2016 3
INSTALLATION INSTRUCTIONS STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.
• Remove the factory radio.
STEP 2
• If the vehicle is equipped with an OEM backup camera: Cut the reverse camera plug of the TO2 T-harness and connect the wires as indicated in the wiring diagram next page (BROWN/RED and BROWN/YELLOW wires are not used).
STEP 3
• Connect the factory harness to the TO2 T-harness.
STEP 4• Plug the male WHITE 2 pin connector of your TO2
T-harness into the OBDII harness.
• Plug the OBDII connector into the OBDII of the vehicle.
STEP 5• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the aftermarket radio (if equipped).
• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).
• Plug the Data cable to the data port of the aftermarket radio.
STEP 6• Connect all the harnesses to the Maestro RR module then
test your installation.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
8
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota venza with JBl 2015-2016
Automotive Data Solutions Inc. © 2016 4
AUX INAUX IN
A
G
F
A FG
9
H
H
BACKUP CAMBACKUP CAM
MAINHARNESS
RCA CABLES
RCA CABLES
FACTORY RADIO HARNESS
REVERSE CAMERA HARNESS
TO2 T-HARNESS
STEP 2
STEP 3
STEP 5
WIRES FROMVEHICLE
CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO
CONNECT IF EQUIPPED
CONNECT TOAFTERMARKET RADIO
STEP 6
MAESTRO RR MODULE
DATACABLE
OBDII CONNECTORSTEP 4
WIRING DIAGRAM with an Amplifier
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
YELLOW/BLACK - FOOT BRAKE
ORANGE - ILLUMINATION (+)YELLOW/GREEN YELLOW/GREEN - REVERSE LIGHT (+)
PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
STEP 1WHITEWHITE/BLACKGRAYGRAY/BLACK
LF RCA INPUT
RF RCA INPUT
SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
CONNECTIONSNOTREQUIREDWITH AMP
PURPLE/WHITE (NOT CONNECTED)PURPLE/WHITE (NOT CONNECTED)
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota venza with JBl 2015-2016
Automotive Data Solutions Inc. © 2016 5
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White or Yellow/Green (see Wiring Diagram) Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness
INSTALL GUIDETOyOTA vENzA
WITh JBL AND NAv 2013-2014Retains factoRy amplifieR, steeRing wheel contRols, and moRe!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota venza with JBl and nav 2013-2014
Automotive Data Solutions Inc. © 2016 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Radio Wire Reference Chart 5
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota venza with JBl and nav 2013-2014
Automotive Data Solutions Inc. © 2016 3
INSTALLATION INSTRUCTIONS STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.
• Remove the factory radio.
STEP 2
• If the vehicle is equipped with an OEM backup camera: Cut the reverse camera plug of the TO2 T-harness and connect the wires as indicated in the wiring diagram next page (BROWN/RED and BROWN/YELLOW wires are not used).
STEP 3
• Connect the factory harness to the TO2 T-harness.
STEP 4• Plug the male WHITE 2 pin connector of your TO2
T-harness into the OBDII harness.
• Plug the OBDII connector into the OBDII of the vehicle.
STEP 5• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the aftermarket radio (if equipped).
• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).
• Plug the Data cable to the data port of the aftermarket radio.
STEP 6• Connect all the harnesses to the Maestro RR module then
test your installation.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
8
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota venza with JBl and nav 2013-2014
Automotive Data Solutions Inc. © 2016 4
AUX INAUX IN
23 1456789101213 11141516
A FG
A
G
F
8
H
H
BACKUP CAMBACKUP CAM
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
YELLOW/BLACK - FOOT BRAKEPURPLE/WHITE (NOT CONNECTED)PURPLE/WHITE (NOT CONNECTED)
ORANGE - ILLUMINATION (+)YELLOW/GREEN YELLOW/GREEN - REVERSE LIGHT (+)
PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
MAINHARNESS
RCA CABLES
RCA CABLES
STEP 1 STEP 5WHITEWHITE/BLACKGRAYGRAY/BLACK
LF RCA INPUT
RF RCA INPUT
CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO
SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
CONNECT TOAFTERMARKET RADIO
WIRING DIAGRAM with an Amplifier
CONNECTIONSNOTREQUIREDWITH AMP
YELLOW REDWHITE
BLACK
BLACK
BLUE/YELLOWBLACK
FACTORY RADIO HARNESS
REVERSE CAMERA HARNESS
TO2 T-HARNESS
STEP 2
STEP 3
WIRES FROMVEHICLE
STEP 6
MAESTRO RR MODULE
DATACABLE
CUT REVERSECAMERACONNECTOR FROMTO2 T-HARNESSAND CONNECTWIRES AS SHOWN.
CONNECT IF EQUIPPED
OBDII CONNECTORSTEP 4
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota venza with JBl and nav 2013-2014
Automotive Data Solutions Inc. © 2016 5
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White or Yellow/Green (see Wiring Diagram) Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS
PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness
INSTALL GUIDETOyOTA vENzA
WIThOUT JBL 2015-2016Retains factoRy amplifieR, steeRing wheel contRols, and moRe!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota venza without JBl 2015-2016
Automotive Data Solutions Inc. © 2016 2
WELCOME
NEED hELP?
Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.
Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
DURING INSTALLATION
Installation Instructions 3
Wiring Diagram 4
Radio Wire Reference Chart 5
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota venza without JBl 2015-2016
Automotive Data Solutions Inc. © 2016 3
INSTALLATION INSTRUCTIONS STEP 1
• Unbox the aftermarket radio and locate its main harness.
• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.
• Remove the factory radio.
STEP 2
• If the vehicle is equipped with an OEM backup camera: Cut the reverse camera plug of the TO2 T-harness and connect the wires as indicated in the wiring diagram next page (BROWN/RED and BROWN/YELLOW wires are not used).
STEP 3
• Connect the factory harness to the TO2 T-harness.
STEP 4• Plug the male WHITE 2 pin connector of your TO2
T-harness into the OBDII harness.
• Plug the OBDII connector into the OBDII of the vehicle.
STEP 5• Plug the aftermarket radio harnesses into the aftermarket
radio.
• Connect the backup camera RCA cable into the aftermarket radio (if equipped).
• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).
• Plug the Data cable to the data port of the aftermarket radio.
STEP 6• Connect all the harnesses to the Maestro RR module then
test your installation.
TROUBLESHOOTING TIPS:
• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.
• For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
8
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota venza without JBl 2015-2016
Automotive Data Solutions Inc. © 2016 4
AUX INAUX IN
A
G
F
A FG
10
H
H
BACKUP CAMBACKUP CAM
YELLOW - 12V (+)
BLACK - GROUNDRED - ACCESSORY (+)
YELLOW/BLACK - FOOT BRAKE
ORANGE - ILLUMINATION (+)YELLOW/GREEN YELLOW/GREEN - REVERSE LIGHT (+)
PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
MAINHARNESS
RCA CABLES
FACTORY RADIO HARNESS
REVERSE CAMERA HARNESS
TO2 T-HARNESS
STEP 1
STEP 2
STEP 3
STEP 5
WIRES FROMVEHICLE
CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO
SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS
GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)
CONNECT TOAFTERMARKET RADIO
STEP 6
MAESTRO RR MODULE
DATACABLE
OBDII CONNECTORSTEP 4
CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS
WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)
WIRING DIAGRAM without an Amplifier
CONNECT IF EQUIPPED
PURPLE/WHITE (NOT CONNECTED)PURPLE/WHITE (NOT CONNECTED)
ADS-RR(SR)-TOY02-DS maestro.idatalink.com
toyota venza without JBl 2015-2016
Automotive Data Solutions Inc. © 2016 5
RADIO WIRE REFERENCE CHART
WireDescription Polarity Wire Color on Maestro
T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable
Illumination (+) Orange N/A Orange/White Orange/White
Reverse Light (+) Purple/White or Yellow/Green (see Wiring Diagram) Orange/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N/A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink