hose guide - pirtekprivate.pirtekusa.com/admin/hoseguide2015web.pdf · will handle petroleum based...

1

HOSE GUIDE

2

PFMU - 18

PFMU - 21

High Pressure Hose

High Pressure Hose

ConstructionInner Tube: Oil resistant synthetic rubber.Reinforcement: Spiraled high tensile steel wire.Cover: Black synthetic rubber, abrasion resistant PIRTEKTOR cover - MSHA approved.

ApplicationMedium to high pressure hydraulic oil lines.

FeaturesWill handle petroleum based hydraulic fluids, air, andlubricating oils.Conforms to SAE 1754B.

Temperature Range-40° F to +210° F. Air Max +158° F, Water +185° F.

Burst Pressure4 times working pressure (4:1 safety factor)

ConstructionInner Tube: Oil resistant synthetic rubber.Reinforcement: Spiraled high tensile steel wire.Cover: Black synthetic rubber, abrasion resistant PIRTEKTOR cover - MSHA approved.


FeaturesWill handle petroleum based hydraulic fluids, air, andlubricating oils.Conforms to SAE 1754B. Temperature Range-40° F to +210° F. Air Max +158° F, Water +185° F.


Nominal I.D. Type Hose I.D.* Wire O.D.* Hose O.D.* Bend* WPInches mm Min Max Min Max Min Max Radius (PSI)

1 1/2 40 PFMU18-24 1.484 1.547 1.937 2.031 2.043 2.110 17 2500


1 1/4 32 PFMU21-20 1.236 1.299 1.681 1.776 1.787 1.854 13 1/2 3000

3

PFMU - 25 High Pressure Hose

ConstructionInner Tube: Oil and heat resistant synthetic rubber.Reinforcement: Braided high tensile steel wire or spiraled high tensile steel wire.Cover: Black synthetic rubber, abrasion resistant PIRTEKTOR cover - MSHA approved.


FeaturesWill handle petroleum based hydraulic fluids, air, diesel fuels and lubricating oils.Conforms to SAE 1754B, 1942-1, ISO18752. Sizes -04 to -16, US Coast Guard approved.




1/4 6.5 PFMU25-04 0.244 0.276 0.382 0.413 0.445 0.500 3 36003/8 9.5 PFMU25-06 0.366 0.398 0.520 0.567 0.591 0.665 4 36001/2 13 PFMU25-08 0.484 0.531 0.642 0.697 0.709 0.776 6 36005/8 16 PFMU25-10 0.610 0.657 0.811 0.866 0.913 0.980 7 36003/4 19 PFMU25-12 0.740 0.780 0.976 1.031 1.059 1.126 8 3/4 36001 25 PFMU25-16 0.984 1.039 1.280 1.343 1.354 1.441 11 3600

1 1/4 32 PFMU25-20 1.236 1.299 1.646 1.740 1.748 1.854 12 1/2 36001 1/2 38 PFMU25-24 1.484 1.547 1.882 1.961 2.043 2.169 17 3600

2 51 PFMU25-32 1.984 2.047 2.449 2.528 2.618 2.744 22 1/2 3600

PFMU - 35 High Pressure Hose

ConstructionInner Tube: Oil and heat resistant synthetic rubber.Reinforcement: Braided high tensile steel wire.Cover: Black synthetic rubber, abrasion resistant PIRTEKTOR cover - MSHA approved.


FeaturesWill handle petroleum based hydraulic fluids, air, diesel fuels and lubricating oils.Conforms to SAE 1754B, 1942-1, ISO18752.US Coast Guard approved.ABS Approved




1/4 6.5 PFMU35-04 0.244 0.276 0.417 0.457 0.500 0.555 3 1/2 50003/8 9.5 PFMU35-06 0.366 0.398 0.575 0.622 0.646 0.709 4 3/4 50001/2 13 PFMU35-08 0.484 0.531 0.689 0.748 0.768 0.846 6 3/4 50005/8 16 PFMU35-10 0.610 0.657 0.874 0.937 0.953 1.031 7 1/2 5000

4

PFMU - 35S High Pressure Hose

ConstructionInner Tube: Oil and heat resistant synthetic rubber.Reinforcement: Spiraled high tensile steel wire.Cover: Black synthetic rubber, abrasion resistant PIRTEKTOR cover - MSHA approved.


FeaturesWill handle petroleum based hydraulic fluids, air, diesel fuels and lubricating oils.Conforms to SAE 1754B, 1942-1, ISO18752.US Coast Guard approved.ABS Approved




3/4 19 PFMU35S-12 0.740 0.780 1.059 1.122 1.157 1.236 10 1/4 50001 25 PFMU35S-16 0.984 1.039 1.343 1.406 1.457 1.535 14 1/4 5000

1 1/4 32 PFMU35S-20 1.236 1.299 1.646 1.740 1.748 1.854 15 3/4 50001 1/2 38 PFMU35S-24 1.484 1.547 2.091 2.185 2.197 2.315 19 3/4 5000

2 51 PFMU35S-32 1.984 2.047 2.634 2.728 2.736 2.862 24 3/4 5000

PFMU - 42 Ultra High Pressure Hose


Application: Ultra high pressure hydraulic oil lines.

FeaturesWill handle petroleum based hydraulic fluids, air, diesel fuels and lubricating oils.Conforms to SAE 1754B, 1942-1, ISO18752. US Coast Guard approved.




1/4 6.5 PFMU42-04 0.244 0.276 0.425 0.465 0.484 0.547 4 60003/8 9.5 PFMU42-06 0.366 0.398 0.661 0.709 0.811 0.874 6 60001/2 13 PFMU42-08 0.484 0.531 0.787 0.835 0.937 1.000 8 60005/8 16 PFMU42-10 0.610 0.657 0.921 0.976 1.091 1.154 9 60005/8 16 PFMU42HB-10 0.610 0.657 0.870 0.902 0.909 0.972 4 1/2 60003/4 19 PFMU42-12 0.740 0.780 1.059 1.122 1.173 1.236 10 1/4 60001 25 PFMU42-16 0.984 1.039 1.374 1.437 1.480 1.567 13 6000

1 1/4 32 PFMU42-20 1.236 1.299 1.795 1.890 1.902 2.020 17 60001 1/2 38 PFMU42-24 1.484 1.547 2.091 2.185 2.197 2.315 20 1/2 6000

2 51 PFMU42-32 1.984 2.047 2.638 2.756 2.776 2.894 27 1/2 6000

5

100STH Teflon Medium Pressure Smooth Bore Hose

ConstructionInner Tube: Extruded white PTFE tube.Reinforcement: Stainless steel wire braid.

ApplicationAutomotive, transportation, food and beverage and injection molding.

FeaturesWill handle petroleum based hydraulic fluids, diesel fuels and lubricating oils.

Temperature Range-65° F to +450° F For more information on specific high temperature ratings please contact your local Pirtek Center.

Burst Pressure4 times WP (4:1) as below at 71°

Nominal I.D. Type Hose O.D.* Bend* Vacuum WPInches mm Nominal Radius Hg (PSI)

3/16 5 100STH-03 0.30 2 28.90 30001/4 6.5 100STH-04 0.37 2 3/8 28.90 3000

5/16 8 100STH-05 0.40 4 28.90 25003/8 10.5 100STH-06 0.49 2 1/4 28.90 22501/2 13 100STH-08 0.59 5 1/2 28.90 17505/8 16 100STH-10 0.80 6 1/2 15.00 15003/4 19 100STH-12 0.87 7 1/2 15.00 11001 25 100STH-16 1.15 10 3/4 13.00 900

SAE 100R2/AT High Pressure Hose



FeaturesWill handle petroleum based hydraulic fluids, air, diesel fuels and lubricating oils.Conforms to SAE EN 853 2SN, SAE 1942-1.US Coast Guard approved.




1 1/4 32 100R2AT-20 1.236 1.299 1.705 1.799 1.854 1.949 16 1/2 18001 1/2 38 100R2AT-24 1.484 1.547 1.953 2.047 2.098 2.201 19 3/4 1300

2 51 100R2AT-32 1.984 2.047 2.453 2.547 2.598 2.701 25 1/2 1140

6

SAE 100R5 Medium Pressure Textile Braided Hose

ConstructionInner Tube: Oil and heat resistant synthetic rubber.Reinforcement: One textile braid and one braid of high tensile steel wire.Cover: Black textile braid impregnated with rubber, resistant to oil, fuel and weathering.

ApplicationMedium pressure hydraulic oil lines.

FeaturesWill handle petroleum based hydraulic fluids, air, water,

diesel fuels, lubricating oils and anti-freeze solution.Meets or exceeds SAE 100R5 requirements.Meets SAE 1402 standard for automotive air brake hose and hose assemblies.

Temperature Range-40° F to +302° F the maximum working pressure shown in the table are for service up to a maximum of 212° F. Exceptions: Air - Max +158° F, Water - Max +185° F. For more information on specific high temperature ratings please contact your local Pirtek Center.

Nominal I.D. Type Hose I.D.* Hose O.D.* Bend* WPInches mm Min Max Min Max Radius (PSI)

3/16 5 100R5-04 0.19 0.20 0.50 0.54 3 30001/4 6.5 100R5-05 0.25 0.28 0.56 0.60 3 1/2 3000

5/16 8 100R5-06 0.31 0.34 0.66 0.69 4 225013/32 10.5 100R5-08 0.41 0.44 0.74 0.79 4 1/2 2000

1/2 13 100R5-10 0.50 0.54 0.90 0.94 5 1/2 17505/8 16 100R5-12 0.63 0.67 1.06 1.10 6 1/2 15007/8 22 100R5-16 0.87 0.92 1.20 1.27 7 1/4 800

1 1/8 29 100R5-20 1.13 1.17 1.47 1.53 9 6251 3/8 35 100R5-24 1.37 1.42 1.72 1.78 10 1/2 500

1 13/16 46 100R5-32 1.81 1.86 2.17 2.27 13 1/4 350

SAE 100R4 Medium Pressure Textile Braided Hose

ConstructionInner Tube: Seamless black synthetic rubber.Reinforcement: One braid of textile fiber with two helix wires to prevent collapse under vacuum. Cover: Black synthetic rubber. Resistant to abrasion, fuel and weathering.

Meets or exceeds SAE 100R4 requirements.

ApplicationPetroleum and water-based hydraulic fluids in suction lines or in low pressure return lines. Suction up to 28 in. of mercury.


Nominal I.D. Type Hose O.D. Min Bend Pressures (PSI)Inches mm Max Radius Working

3/4 19 100R4-12 1.380 5.0 3001 25 100R4-16 1.630 6.0 250

1 1/4 32 100R4-20 2.000 8.0 2001 1/2 38 100R4-24 2.250 10.0 150

2 51 100R4-32 2.750 12.0 1002 1/2 63.5 100R4-40 3.250 14.0 62

3 76 100R4-48 3.780 18.0 56

7

100R7NC Thermoplastic Medium Pressure Non-Conductive Hose

ConstructionPolyester core tube, fiber reinforcement, abrasion resistant. Special electrically non-conductive polyester cover. High density braid for maximum impulse life without loss of flexibility. Standard cover is orange, non-perforated.

ApplicationsMedium pressure hydraulic and pneumatic service. For hydraulic systems found on industrial, and mobile equipment.

FeaturesMeets or exceeds SAE 100R7 specifications for non-conductive hose.

Temperature Range-40°F to +212°F (-40°C to 100°C) except limited to +135°F (+57°C) for synthetic hydraulic fluids and water based fluids .

Nominal I.D. Type Hose O.D.* Bend* WPInches mm Maximum Radius (PSI)

3/16 5 100R7NC-03 0.43 3/4 32501/4 6.5 100R7NC-04 0.51 1 1/4 3000

5/16 8 100R7NC-05 0.57 1 3/4 25003/8 9.5 100R7NC-06 0.65 2 22501/2 13 100R7NC-08 0.81 3 2000

100R7 Thermoplastic Medium Pressure Hose

ConstructionPolyester core tube with fiber reinforcement. All layers bonded. Standard cover is black and perforated for pneumatic service.

ApplicationsMedium pressure hydraulic and pneumatic service. For hydraulic and pneumatic circuits and systems found on agricultural, industrial, and construction equipment.

Ideal for use at low temperature on fork trucks in refrigerated warehouses.

FeaturesMeets or exceeds SAE 100R7 specifications.

Temperature Range-70°F to +212°F (-57°C to 100°C) except limited to +135°F (+57°C) for synthetic hydraulic fluids and water based fluids.


1/8 3 100R7-02 0.34 1/2 30003/16 5 100R7-03 0.43 3/4 32501/4 6.5 100R7-04 0.51 1 1/4 3000

5/16 8 100R7-05 0.57 1 3/4 25003/8 9.5 100R7-06 0.65 2 22501/2 13 100R7-08 0.81 3 2000

Also available in Twinline Hose. For Twinline Hose part number place T after 100R7.

8

100R8NC Thermoplastic High Pressure Non-Conductive Hose

100R8 Thermoplastic High Pressure Hose


3/16 5 100R8-03 0.43 1 1/2 50001/4 6.5 100R8-04 0.51 2 5000

5/16 8 100R8-05 0.57 2 1/2 45003/8 9.5 100R8-06 0.65 2 1/2 40001/2 13 100R8-08 0.81 4 3500

ConstructionNylon core tube, fiber reinforcement, abrasion resistant cover. All layers bonded for optimum kink resistance and flexibility. High density braid for maximum impulse life without loss of flexibility. Standard cover is orange, non-perforated.

ApplicationsHydraulic and pneumatic circuits and systems. Replaces 100R2 rubber hose wherever greater flexibility, fluid compatibility and cover durability are required, lighter weight and smaller O.D. than 100R2. Aramid reinforcement yarn provides low volumetric expansion

in a minimum O.D. hose. Ideal for use in hot water applications. Not recomended for use over the sheave.

FeaturesAramid reinforcement for compact strength and flexibility.Meets or exceeds SAE 100R8 requirements for non-conductive hose.

Temperature Range-40°F to +212°F (-40°C to 100°C) except limited to +135°F (+57°C) for synthetic hydraulic fluids and water based fluids .


3/16 5 100R8NC-03 0.43 1 1/2 50001/4 6.5 100R8NC-04 0.51 2 5000

5/16 8 100R8NC-05 0.57 2 1/2 45003/8 9.5 100R8NC-06 0.65 2 1/2 40001/2 13 100R8NC-08 0.81 4 3500

ConstructionNylon core tube, aramid reinforcement, abrasion resistant urethane cover. All layers bonded. Standard cover is black and perforated for pneumatic service.

ApplicationsHydraulic and pneumatic circuits and systems. Replaces 100R2 rubber hose wherever greater flexibility, fluid compatibility and cover durability are required, lighter weight and smaller O.D. than 100R2. Aramid reinforcement yarn provides low volumetric expansion

in a minimum O.D. hose. Ideal for use in hot water applications. Not recomended for use over the sheave.

FeaturesMeets or exceeds SAE 100R8 requirements.Aramid reinforcement for compact strength and flexibility.

Temperature Range-40°F to +212°F (-40°C to 100°C).

9

Size Nominal I.D. Hose ID Hose OD BendInches MM MM Inch MM Inch Radius

6 5/16 8 7.87 0.31 19.10 0.75 38 13/32 10.5 10.60 0.42 23.00 0.91 3 3/4

10 1/2 13 12.78 0.50 35.40 1.00 412 5/8 16 16.20 0.64 28.60 1.12 4 1/2

ConstructionInner Tube: Chlorinated Polyethylene.Reinforcement: PVA spiral reinforcement.Cover: EPDM for heat & ozone resistance.

ApplicationAit conditioning using refrigerants.

FeaturesLow effusion capabilities, good vacuum characteristics.Meets or Exceeds SAE J 2064.

Temperature Range-20F to +250F.

Barrier Air Conditioning Hose 13/32

100AC5 Air Conditioning Hose

100R5HT High Temperature Textile Braided Hose

ConstructionInner Tube: Synthetic rubber.Reinforcement: One textile braid and one braid of high tensile steel wire.Cover: Blue polyester braid.

ApplicationLow to medium pressure hose.

FeaturesWill handle petroleum based hydraulic fluids, air, water and fuel. Meets or Exceeds SAE J517 (100R5).

Temperature Range-55 F to +302 F. Air Max +250 F. Water Max +150 F. For more information on specific high temperature ratings please contact your local Pirtek Center.

Type Hose ID Hose OD Min Bend Radius Max WP

Inches mm Inches mm Inches (PSI)100R5HT-04 3/16 5 0.52 13.2 3 3000100R5HT-06 5/16 8 0.67 17.3 4 2250100R5HT-08 13/32 10.5 0.76 19.6 4 1/2 2000100R5HT-10 1/2 13 0.93 23.4 5 1/2 1750100R5HT-12 5/8 16 1.08 27.4 6 1/2 1500100R5HT-16 7/8 22 1.27 31.2 7 1/4 800100R5HT-20 1 1/8 29 1.50 38.1 9 625

10

PJK High Pressure Hose

ConstructionInner Tube: Nitrile.Reinforcement: Spiraled high tensile steel wire.Cover: Black synthetic rubber, abrasion resistant

ApplicationStatic Jack Hose.

FeaturesWill Handle petrolium based hydraulic fluids, andlubricating oils. Temperature Range-40° F to +120° F.

PIRJACK Hose as a 2:1 design factor. Meets Flame resistance designation MSHA 1C 40-26. Pirtektor abraision resistant cover.

Nominal I.D. Type Hose I.D.* Hose O.D.* Bend* WPInches mm Inches mm Inches mm Radius (PSI)

1/4 6.5 PJK-04 1/4 6.5 0.52 13.1 3 10,000

‘PIRTEK PIRJACK PJK-04 1/4’ (6.5 mm) WP 10,000 psi 9 700 bar) STATIC . PIRTEKTOR Cover MSHA 1C 40-26 IJ1OO www.pirtekusa.com

11

The Benefits of Using PIRTEK ETA 1 Hour On-Site 24 Hours – 7 Days Removal & Installation Assemble Hoses On-Site Wide Range of Inventory Metric Specialists National – Regional Network Hose Cleaning Hose Tagging Reduce Costly Downtime

hose guide - pirtekprivate.pirtekusa.com/admin/hoseguide2015web.pdf · will handle petroleum based...

Documents