hipath 3000 hipath 5000 rsm optipoint 500 entry

HiPath 3000HiPath 5000 RSMHiPath AllServe, Hicom 150 E/H

optiPoint 500 entry

Operating Instructions

Before You Begin

2

Before You BeginThese operating instructions describe the optiPoint 500 entry telephone on your HiPath 3000 / 5000 RSM.They describe all functions you can use from your telephone. You may find that some func-tions you wish to use are not available on your telephone. This may be due to one of the following reasons:• The function has not been configured for your telephone - please contact your service

personnel.• Your communications platforms does not support this function - please contact your

service personnel.

Important Notes

Never allow the telephone to come into contact with staining or aggressive liquids such as coffee, tea, juice, or soft drinks.For information on telephone maintenance Page 58.

The information provided in this document contains merely general descriptions or charac-teristics of performance which in case of actual use do not always apply as described or which may change as a result of further development of the products.An obligation to provide the respective characteristics shall only exist if expressly agreed in the terms of contract.

Marks

Do not operate the telephone in environments where there is a danger of explosions.

Use only original Siemens accessories. Using other accessories may cause a hazard and will invalidate the warranty and the CE mark.

Never open the telephone or a key module. If you encounter any problems, contact the service personnel.

The device conforms to the EU guideline 1999/5/EG, as attested by the CE mark.

This device has been manufactured in accordance with our certified environ-mental management system (ISO 14001). This process ensures that energy consumption and the use of primary raw materials are kept to a minimum, thus reducing waste production.

Contents

Contents

Basic operating instructions . . . . . . . . . . . . . . . . . . . . 7optiPoint 500 entry control panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7How to Use these Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . 8Accessing Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

... With Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

... With Function Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Making Calls – Basic Functions . . . . . . . . . . . . . . . . 10Making and Answering Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Answering a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Open Listening in the Room During a Call . . . . . . . . . . . . . . . . . . . . . . 10Dialing Numbers/Making Calls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Answering a Call With the Handset . . . . . . . . . . . . . . . . . . . . . . . . . 11On-Hook Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Ending the call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Redialing a Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Turning the Microphone On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Calling a Second Party (Consultation Hold) . . . . . . . . . . . . . . . . . . . . . . 12

Switching to the Party on Hold (Toggle) . . . . . . . . . . . . . . . . . . . . . 13Transferring a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Call Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Using Variable Call Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Call Forwarding in the Carrier Networkand Forwarding Multiple Subscriber Numbers (MSN) (Not for U.S.) 14

Using Callback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Storing a Callback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Answering a Callback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Deleting (All) Stored Callbacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Telephone Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Adjusting the Ring Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Adjusting the Ring Tone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Adjusting the Receiving Volume During a Call . . . . . . . . . . . . . . . . . 16

Making Calls – Convenience Functions . . . . . . . . . 17Making Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Accepting a Specific Call for Your Colleague . . . . . . . . . . . . . . . . . . 17Rejecting Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Using the Speakerphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Answering Calls from the Entrance Telephoneand Opening the Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3

Contents

Dialing Numbers/Making Calls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Speed-Dial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Using Mailboxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Talking to Your Colleague With a Speaker Call . . . . . . . . . . . . . . . . 20Automatic Connection Setup (Hotline). . . . . . . . . . . . . . . . . . . . . . . 21Reserve Trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Assigning a Station Number (Not for U.S.) . . . . . . . . . . . . . . . . . . . 21Associated Dialing/Dialing Aid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

During a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Using Call Waiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Accepting a Waiting Call (Camp-On) . . . . . . . . . . . . . . . . . . . . . . . . 23Preventing and Allowing Call Waiting (Automatic Camp-On). . . . . . 24Turning the Call Waiting Tone On and Off . . . . . . . . . . . . . . . . . . . . 24Parking a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Picking up (Retrieving) a Held Call . . . . . . . . . . . . . . . . . . . . . . . . . . 25Conducting a Conference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Activating Tone Dialing (DTMF Suffix Dialing) . . . . . . . . . . . . . . . . . 27After a Speaker Call (Announcement) in a Group . . . . . . . . . . . . . . 28Trunk Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

If You Cannot Reach a Destination . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Call Waiting (Camp-On) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Busy Override - Joining a Call in Progress . . . . . . . . . . . . . . . . . . . . 29

Using Night Answer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Appointments Function. . . . . . . . . . . . . . . . . . . . . . . .31Saving Appointments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Using Timed Reminders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Displaying and Assigning Call Charges. . . . . . . . . .32Dialing with Call Charge Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Private Sphere/Security . . . . . . . . . . . . . . . . . . . . . . .33Turning Do Not Disturb On and Off. . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Caller ID Suppression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Silent Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Monitoring a Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Trace Call: Identifying Anonymous Callers (Not for U.S.) . . . . . . . . . . . 35Locking the Telephone to Prevent Unauthorized Use . . . . . . . . . . . . . . 35Locking Another Telephone to Prevent Unauthorized Use . . . . . . . . . . 36Saving Your PIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

4

Contents

Using Other Functions/Services . . . . . . . . . . . . . . . . 37Sending a Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Deleting Sent Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Answering Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Using Another Telephone Like Your Own . . . . . . . . . . . . . . . . . . . . . . . 38Change call number (relocate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39Resetting Services and Functions(System-Wide Cancellation for a Telephone). . . . . . . . . . . . . . . . . . . . . 40Activating Functions for Another Telephone . . . . . . . . . . . . . . . . . . . . . 41Using System Functions from the Outside(DISA: Direct Inward System Access) . . . . . . . . . . . . . . . . . . . . . . . . . . 41Controlling Connected Computers or Other Programs and Telephone Data Service (For HiPath 3500/3550/3700/3750 only) . 43Controlling Relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Radio Paging (Not for U.S.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Simple Paging Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Enhanced Paging Equipment (Hipath 3700/3750 Only) . . . . . . . . . . 45

Using Team Functions . . . . . . . . . . . . . . . . . . . . . . . . 46Turning Group Call On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46Accepting a Call for Another Member of Your Team . . . . . . . . . . . . . . 47Activating and Deactivating a Ringing Group. . . . . . . . . . . . . . . . . . . . . 47Uniform Call Distribution (UCD). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Team and Executive/Secretary Functions WithAssigned Trunk Lines . . . . . . . . . . . . . . . . . . . . . . . . . 49Forwarding Calls on Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Transferring Calls Directly to the Executive (Only in an Executive/Secretary Group) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Testing the Telephone . . . . . . . . . . . . . . . . . . . . . . . . 50Testing the Telephone Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Special Functions in the LAN (PC Network). . . . . . 51Leaving a Hunt Group/Group Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51Transferring Call Forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Using Night Answer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53Activating and Deactivating a Ringing Group. . . . . . . . . . . . . . . . . . . . . 54Controlling Relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55Opening the Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

5

Contents

Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57

Fixing Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58Telephone Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

Overview of Functions and Codes (Alphabetical) .63

FCC and Industry Canada Compliance. . . . . . . . . . .69FCC Certification and Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . 69Equipment Attachment Limitations. . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

6

Basic operating instructions


optiPoint 500 entry control panel

Keys fortelephone settings

Keypad

Handset

Speakerfor ring tones

Eight fixed function keys:ConsultationRedialMessage WaitingCallbackSpeed DialMuteSpeakerRelease

LEDs

Your service personnel can customize the default assignment to meet your preferences and requirements following order placement.

7

Step by Step


How to Use these Operating InstructionsYou will find a graphic representation of the steps in log-ical sequence in the left column. Below is an explana-tion of the symbols:

n Lift the handset (off-hook).

t Replace the handset (on-hook).

s Conduct a call.

o Enter a telephone number or code.

dd Enter the PIN.

u or v Press volume controls on the telephone.

w You hear a tone.A long tone (positive confirmation tone) confirms that you have successfully activated a function or procedure.A short tone (negative confirmation tone) indicates that the function or procedure was rejected.

Press the key.

Press the illuminated key.

Press the flashing key.

8


Step by Step

Accessing Functions... With CodesYou can activate the functions of your system by entering codes such as:

qmk DND (do not disturb) on.

rmk DND (do not disturb) off.

All codes to activate or enable functions are always introduced by pressing the star key, and all codes to deactivate, disable or delete functions are always entered starting with the pound key.

An alphabetically ordered overview of all functions and their corresponding codes can be found in the Appendix (Quick-Reference Operating Instructions).

... With Function KeysFunctions for which a key has been set up can be accessed directly as follows.

Press the "consultation hold" key. The function is executed, provided this is possible in the current situation.

If your service personnel has changed the default assignments and saved functions on keys in ac-cordance with your requests or requirements, you can execute these functions by pressing the appropriate keys.

9

Step by Step

Making Calls – Basic Functions


Making and Answering CallsSpecial default ring signaling is set for your telephone:

• When you receive an internal call, your telephone rings once every four seconds (single-tone se-quence).

• When you receive an external call, your telephone rings twice in rapid succession every four seconds (dual-tone sequence).

• When you receive a call from the entrance tele-phone, your telephone rings three times in rapid succession every four seconds (triple-tone se-quence).

• If a call is waiting, you hear a short tone (beep) every six seconds.

Answering a Call

The telephone rings.

n Lift the handset.

u or v To raise or lower the volume, keep pressing the keys un-til the desired volume is set.

Open Listening in the Room During a CallYou can let other people in the room join in on the call. Let the other party know that you have turned on the speaker.

Precondition: You are conducting a call with the hand-set.

Activating this function:

Press the key. The LED lights up.

Deactivating this function:

Press the key. The LED goes out.

Speaker

Speaker

10


Step by Step

Dialing Numbers/Making Calls

Answering a Call With the Handset

n Lift the handset.

o Internal calls: Enter the station number.External calls: Enter the external code and the station number.

The called party does not answer or is busy:

t Replace the handset. or

Press the key.

On-Hook Dialing

o Internal calls: Enter the station number.External calls: Enter the external code and the station number.

The other party answers with speaker:

n Lift the handset.

The called party does not answer or is busy:

Press the key. The LED goes out.or

Press the key.

Ending the call

t Replace the handset.or

Press the key.

Release

Speaker

Release

Release

11

Step by Step


Redialing a NumberThe last three external telephone numbers dialed are stored automatically.You can redial them simply by pressing a key.

n Lift the handset.

Press this key.

Turning the Microphone On and OffTo prevent the other party from listening in while you consult with someone in your office, you can temporar-ily switch off the handset microphone or the handsfree microphone.

Precondition: You are conducting a call. The microphone is switched on.


Turning off the mute:

Press the illuminated key. The LED goes out.

Calling a Second Party (Consultation Hold)You can call a second party while engaged in a call. The first party is placed on hold.

Press the key. LED flashes.

o Call the second station.

Return to the first party:

Press this key and wait two seconds.

or (depending on the configuration)

Press the key twice.

Redial

If this feature is configured (contact the service personnel), accounts codes entered are also saved Page 32.

Mute

Mute

Consultation

Consultation

Consultation

12


Step by Step

Switching to the Party on Hold (Toggle) qf Press the key. Enter the code. LED continues to flash.

Combining the calling parties into a three-party conference

qg Press the key. Enter the code. The LED goes out.

Connecting the other parties to each other

t Replace the handset.

Transferring a CallIf the person you are speaking to wants to talk to anoth-er colleague of yours, you can transfer the call that col-league.


o Enter the number of the party to which you want to transfer the call.

s Announce the call, if necessary.


Call Forwarding

Using Variable Call ForwardingYou can immediately forward internal or external calls to different internal or external telephones (destinations). (External destinations require special configuration in the system).

n Lift the handset.

qe Enter the code.

e or f or g Enter the line type you wish to use: 1 = all calls, 2 = external calls only, 3 = internal calls only

o w Enter the destination number (without the external code).

Consultation

Consultation

Consultation

Special features must be taken into considera-tion if your telephone operates with HiPath 5000 RSM (system networking via PC network) Page 52!

13

Step by Step


Deactivating call forwarding:

n Lift the handset.

re w Enter the code.

Call Forwarding in the Carrier Networkand Forwarding Multiple Subscriber Num-bers (MSN) (Not for U.S.)

If this function has been configured (contact the service personnel), you can forward calls to your assigned multiple subscriber number (MSN) (DID number) directly within the carrier network.For example, you can forward your phone line to your home phone after business hours.

n Lift the handset.

qjh Enter the code.

e or f or g Enter the line type you wish to use:1= immediate, 2 = on no answer, 3 = on busy

o Enter your DID number.



n Lift the handset.

rjh Enter the code.

e or f or g Enter the activated call forwarding type.1= immediate, 2 = on no answer, 3 = on busy

o w Enter your DID number.

When call forwarding is active, a special dial tone sounds when you lift the handset.

If DID DTMF is active (contact the service per-sonnel), you can also forward calls to this desti-nation. Destinations: fax = 870, DID = 871, fax DID = 872.

14


Step by Step

Using CallbackIf a user is busy or is not answering, you can store an automatic callback. This feature saves you from having to make repeated attempts to reach the user.You receive a callback,• When the other party is no longer busy• When the user who did not answer has conducted

another call.

Storing a CallbackPrecondition: You have reached a busy line or noone answers.


or

qilPress the key. LED flashes. Enter the code.

Answering a CallbackPrecondition: A callback was saved. Your telephone rings. The Callback key lights up (if present).

n Lift the handset. You hear a ring tone.

Deleting (All) Stored Callbacks

n Lift the handset.

ril w Enter the code.

Callback

Consultation

15

Step by Step


Telephone Settings

Adjusting the Ring Volume

u or v Press one of these keys while the phone is idle.

e Press the key.

u or v To raise or lower the volume, keep pressing the keys un-til the desired volume is set.

u v simultaneously Save.

Adjusting the Ring Tone

u or v Press one of these keys while the phone is idle.

f Press the key.

u or v To adjust the ring tone, keep pressing the keys until the desired ring tone is set.


Adjusting the Receiving Volume During a Call

You are engaged in a call.

u or v To raise or lower the volume, keep pressing the keys un-til the desired ring tone is set.


16

Making Calls – Convenience Functions

Step by Step


Making Calls

Accepting a Specific Call for Your Colleague

You hear another telephone ring.

n Lift the handset.

qjm Enter the code.

o Enter the number of the telephone that is ringing.

Rejecting Calls

You can reject calls which you do not wish to take. The call is then signaled at another definable telephone (contact the service personnel).

The telephone rings.

Press the key.

If a call cannot be rejected, your telephone will continue to ring.

Using the Speakerphone

A colleague addresses you directly over the speaker with a speaker call. You hear a tone before the an-nouncement.

You can respond with the handset or in speakerphone mode.

n Lift the handset and answer the call.

Accepting calls in a team Page 47.

Release

Placing a speaker call to a colleague Page 20.

17

Step by Step


Answering Calls from the Entrance Telephoneand Opening the DoorIf an entrance telephone has been programmed, you can use your telephone to speak to someone at the entrance telephone and to activate a door opener. If you are authorized to activate a door opener (contact the service personnel), visitors can open the door them-selves by entering a 5-digit code (e.g. using a DTMF transmitter or installed keypad).

Speaking to visitors via the entrance telephone:

Precondition: Your telephone rings.

n Lift the handset within thirty seconds. You are connect-ed to the entrance telephone immediately.

or

n Lift the handset after more than thirty seconds.

o Dial the entrance telephone number.

Opening the door from your telephone during a call from the entrance telephone:

qjePress the key. LED flashes. Enter the code.

o w Dial the entrance telephone number.

Opening the door with a code (at the door):

o After ringing the bell, enter the five-digit code (using the keypad or a DTMF transmitter). Depending on how the door opener has been programmed, a doorbell call sig-nal may or may not be forwarded.

Consultation


18


Step by Step

Activating the door opener:

n Lift the handset.

qlm Enter the code.

o Dial the entrance telephone number.

o w Enter the five-digit code. Default code = "00000" (con-tact the service personnel).

e or f Enter the type of door opener. 1 = enable with ring, 2 = enable w/o ring = You can also open the door with-out a doorbell ring.

Deactivating the door opener:

n Lift the handset.

rlm Enter the code.

o w Dial the entrance telephone number.

Dialing Numbers/Making Calls

Speed-Dial

Using Station and System Speed-Dial Numbers

Precondition: You have stored station speed-dial num-bers Page 20 or the service personnel has stored system speed-dial numbers.

n Lift the handset.

Press the key. or

qk Enter the code.

o Enter a speed-dial number."*0" to "*9" = station speed-dialing."000" to "999" = system speed-dialing (contact the serv-ice personnel).

Speed-dial

19

Step by Step


Storing Station Speed-Dial Numbers

You can store the ten numbers which you use the most and dial them using your own station speed-dial num-bers: *0 through *9 Page 19.

n Lift the handset.

qmf Enter the code.

o w Enter the speed-dial number you wish to use (*0 to

*9).

o w First enter the external code and then the external sta-tion number (wait approx. 5 seconds).

Using MailboxesIf there are messages waiting for you, you will hear a special dial tone (continuous buzzing) when you lift the handset.

n w Lift the handset.

rjlg Enter the code.or


This connects you to the sender of the message or the mailbox system.

Talking to Your Colleague With a Speaker CallYou can make a loudspeaker announcement through a loudspeaker if connected (ask the service personnel), or to an internal user with an system telephone without any action on their part.

n Lift the handset.

qld Enter the code.

o w Enter the station number.

Message Waiting

20


Step by Step

Automatic Connection Setup (Hotline)If this function is configured (contact the service per-sonnel), the system automatically sets up a connection to a preset internal or external destination.

n Lift the handset.Depending on the setting, the connection is either set up immediately or only after a preset period of time (hotline after a timeout).

Reserve TrunkIf this feature is configured (contact the service person-nel), you can reserve a busy trunk for your own use.When the trunk is free, you receive a call.

n Lift the handset.

o Enter the external code. The external trunk is busy; you hear a busy signal tone. Wait about 5 seconds until the busy tone ends.The trunk is reserved.


When the reserved trunk becomes free:

Your telephone rings.

n Lift the handset. You hear the CO dial tone.

o Enter the number of the external station.

Assigning a Station Number (Not for U.S.)If this function has been configured (contact the service personnel), you can selectively assign a specific number (DID number) to your telephone before making an external call. The assigned number then appears on the called party’s display.

n Lift the handset.

qhe Enter the code.

o Enter the DID number you wish to use.

o Dial the external number.

21

Step by Step


Associated Dialing/Dialing AidIf this function has been configured (contact the service personnel), you can use your telephone as a dialing aid for other telephones.

n Lift the handset.

qjk Enter the code.

o w Enter the internal station number of the party for whom you want to dial.

o Enter the number you wish to dial (external number with external code).

22


Step by Step

During a Call

Using Call WaitingCallers can still reach you while you are engaged in an-other call. A signal alerts you to the waiting call.You can either ignore or accept the waiting call.When you accept the waiting call, you can either end the first call or place it on hold and resume the call later on.You can also bar call waiting or the call waiting tone

Page 24.

Accepting a Waiting Call (Camp-On)Precondition: You are engaged in a phone call and hear a tone (every six seconds).

Ending the first call and answering the waiting call:

t Replace the handset. Your telephone rings.

n Answer the second call. Lift the handset.

Placing the first call on hold and answering the sec-ond call:

qiiPress the key. LED flashes. Enter the code.

You are connected to the call waiting party immediately. The first party is placed on hold.

Ending the second call and resuming the first one:

Press this key and wait two seconds.

or (depending on the configuration)


Consultation

Consultation

Consultation

23

Step by Step


Preventing and Allowing Call Waiting (Auto-matic Camp-On)If this function has been configured (ask the service per-sonnel), you can prevent or allow a second call

Page 23 from being signaled by automatic camp-on during an ongoing call.

n Lift the handset.

rhmdor qhmd

w

Enter the code to "prevent" or "allow" call waiting.

Turning the Call Waiting Tone On and OffYou can suppress the call waiting tone every six sec-onds for external calls. A one-time special dial tone then alerts you to the waiting call.

n Lift the handset.

qlk or rlk w Enter code for "tone off" or "tone on".

Parking a CallYou can park up to ten calls, either internal, external, or both. Parked calls can be displayed on and picked up from another telephone. This feature is useful if you want to continue a call at another phone.

Precondition: You are conducting a call.

qijPress the key. LED flashes. Enter the code.

d ... m w Enter the number of the park slot (0 - 9) and make a note of it.If the park slot number you entered is already being used, you will hear the negative confirmation tone. Please enter another number.


Consultation

24


Step by Step

Retrieving a Parked Call

Precondition: One or more calls have been parked. The telephone is idle.

n Lift the handset.

rij Enter the code.

d ... m Enter the park slot number you noted earlier.If the park slot number you enter is not in use, you can-not retrieve the call.

Picking up (Retrieving) a Held Call

Precondition: One or more calls have been parked. The telephone is idle.

n Lift the handset.

qjg Enter the code.

o Enter the line number you noted earlier.

Conducting a ConferenceIn a conference call, you can talk to as many as four oth-er parties at the same time. These may be internal or external users.

n Lift the handset.

o Call the first party.


o Call the second station. Announce the conference.

qg Press the key. Enter the code. The LED goes out.

A tone sounds every 30 seconds to indicate that a con-ference is in progress. Contact the service personnel for instructions on how to turn it off.

If a parked call is not picked up, after a specific period of time the call is returned to the tele-phone from where it was parked (recall).

Consultation

Consultation

25

Step by Step


If the second party does not answer:

Press this key and wait two seconds.or (depending on the configuration)


Adding Up to Five to the Conference(Initiator Only)


o Call the new party. Announce the conference.

qg Press the key. Enter the code. The LED goes out,etc.

Leaving a Conference


Consultation

Consultation

Consultation

Consultation

26


Step by Step

Ending a Conference (Initiator Only)

rg Press the key. LED flashes. Enter the code.

Removing the ISDN Central Office Party From the Conference (Only for U.S.)


qhme Enter the code.

Activating Tone Dialing (DTMF Suffix Dialing)You can transmit dual-tone multifrequency (DTMF) signals to control devices such as an answering machine or automatic information system.

s You have set up a connection.

qigPress the key. LED flashes. Enter the code.

o You can use the keys "0" through "9", "*", and "#" to transmit DTMF signals.

Consultation

Consultation

Consultation

Ending the call also deactivates DTMF suffix dialing.Your system may be configured so that you can start DTMF suffix-dialing immediately after setting up a connection.

27

Step by Step


After a Speaker Call (Announcement) in a GroupIf this function has been configured (contact the service personnel), you can use a speaker call (announcement,

Page 20) to announce a call in progress to a group of users Page 46.After a member of the group has accepted the call re-quest, you can transfer the waiting party.

Precondition: You are conducting a call.

qldPress the key. LED flashes. Enter the code.

o w Enter the group’s station number.

s Announce the call.When a member of the group accepts the call, you are connected to this party.


Trunk FlashTo activate ISDN-type services and features through the network carrier’s analog trunks or those of other com-munications platforms (such as "consultation hold"), you must send a signal to the trunks before dialing the serv-ice code or telephone number.

Precondition: You have set up an external connection via an analog line.

qiePress the key. LED flashes. Enter the code.

o Enter the service code and/or telephone number.

Consultation

If the connection between the two other parties is not established within 45 seconds, the call from the first party returns to you (recall).

Consultation

28


Step by Step

If You Cannot Reach a Destination

Call Waiting (Camp-On)It is important that you reach the called party, but the number is busy.

n Lift the handset.

o Enter the internal station number.Wait (approx. 5 seconds) until the busy tone is followed by the ring tone.

The called party can then respond Page 23.

Busy Override - Joining a Call in ProgressThis function is only available if it has been configured by the service technician (contact the service person-nel).

Precondition: You have dialed an internal number and hear a busy signal. It is important that you reach the called party.

qjf wPress the key. LED flashes. Enter the code.

The called party and person to whom this party is talk-ing hear an alerting tone every two seconds.If the called party has a system telephone with display, the following appears on the screen: "Override: (station no. or name)".

You can now start talking.

The called party can prevent automatic call wait-ing Page 24.

If this feature is configured (contact the service personnel), you will hear the ring tone immedi-ately.

Consultation

29

Step by Step


Using Night AnswerWhen night answer mode is active, for example during a lunch break or after office hours, all external calls are immediately forwarded to a specific internal telephone (night station). The night station can be defined by the service personnel ( standard night answer service) or by you (temporary night answer service).


n Lift the handset.

qhh Enter the code.

o w Enter the destination number (= temporary night an-swer service) within 5 seconds.

orq w Enter the code or use the default (= standard night an-

swer service).


rhh w Enter the code.


30

Appointments Function

Step by Step

Appointments Function

Saving AppointmentsYou can tell your telephone to give you a call when you want to be reminded of an appointment .To do this, you need to save the time you want the call to be made. The appointment can be set for any time within the next 24 hours.

n Lift the handset.

qhj Enter the code.

o Enter a 4-digit time, such as 0905 for 9:05 (= 9.05 a.m.) or 1430 for 14.30 (= 2.30 p.m.).

f or k If the selected language is "US English" (ask the service personnel) enter the code 2 for "am" or 7 for "pm".

w

Deleting and checking a saved appointment

n Lift the handset.

rhj w Enter the code.

Using Timed RemindersPrecondition: You must have saved a timed reminder

Page 31. The current time is the time stored.

n t Your telephone rings.Lift the handset and replace it again.

If you fail to answer the timed reminder, it re-peats five times and is then erased.

31

Step by Step

Displaying and Assigning Call Charges

Displaying and Assigning Call Charges

Dialing with Call Charge AssignmentYou can assign external calls to certain projects.

Precondition: The service personnel has set up account codes for you.

n Lift the handset.

qjd Enter the code.

o Enter the account code.

If applicabler w Press this key (may be needed, depending on the con-

figuration; contact the service personnel).

o Enter the number of the external station.

You can also enter the account code during an external call.

32

Private Sphere/Security

Step by Step


Turning Do Not Disturb On and OffYou can activate the do not disturb function if you do not want the receive any calls. When do not disturb is acti-vated, internal callers hear a busy signal and external callers are rerouted to a telephone assigned for this pur-pose (contact the service personnel).

n Lift the handset.

qmk or rmk w Enter the code for "on" or "off".

Caller ID SuppressionYou can prevent your station number or name from ap-pearing on the displays of external parties you call. The feature remains active until you deactivate it.

n Lift the handset.

qlj or rlj w Enter code for "suppress" or "restore".

When you lift the handset, a special dial tone (continuous buzzing) reminds you that "do not disturb" is active.

Authorized internal callers can automatically override the "do not disturb" function after five seconds.

The service personnel can turn caller ID suppres-sion on and off for all telephones.

33

Step by Step


Silent MonitorIf this function has been configured (contact the service personnel), you can join a call already in progress at an internal station and listen in unnoticed.

n Lift the handset.

qmhh Enter the code.

o Enter the internal station number.

Monitoring a RoomA telephone can be used to monitor a room. The func-tion must be activated on the telephone that you want to monitor.Calling this telephone lets you hear what is going on in the room.

Activating the telephone to be monitored:

n Lift the handset and direct it towards the noise source.

qll w Enter the code.

Deactivating the telephone to be monitored:


Monitoring the room:

n Lift the handset.

o Enter the internal number of the telephone in the room you wish to monitor.

34


Step by Step

Trace Call: Identifying Anonymous Callers (Not for U.S.)You can have the carrier identify malicious external call-ers. You can save the caller’s station number during the call or for 30 seconds after the call ends. However, it is essential that you do not replace your handset during this time.

s You are engaged in an external call.

qlhPress the key. LED flashes. Enter the code.

Locking the Telephone to Prevent Unauthorized UseYou can prevent unauthorized persons from using your telephone during your absence.

Precondition: You must have configured a personal identification number (PIN) for your telephone

Page 36.

To lock and unlock the telephone:

n Lift the handset.

qjj or rjj Enter the code for "lock" or "unlock".

o w Enter the telephone lock PIN Page 36.

Consultation

After you have finished tracing the call, the data is stored on the carrier’s system. Now contact the service personnel.

While the telephone is locked, a special dial tone sounds when you lift the handset. You can con-tinue to dial internal numbers as usual.

An authorized party Page 36 can also lock and unlock your telephone.

35

Step by Step


Locking Another Telephone to Prevent Unauthorized UseIf this function has been configured (contact the service personnel), you can lock other telephones to prevent unauthorized use, and later unlock them again.

You can use this function to unlock the telephone for us-ers who have locked their telephones and then forgot-ten their PINs.

n Lift the handset.

qmhg Enter the code.

o Enter the internal number of the telephone that you want to lock or unlock.

q Enter the code for "Changeover on".or

r Enter the code for "Changeover off".

Saving Your PINTo use the functions• to prevent unauthorized persons from using your

telephone Page 35• to use another telephone like your own Page 38• to change your call number Page 39

you need to enter a personal identification number, which you can save yourself.

n Lift the handset.

qmg Enter the code.

o Enter the current five-digit PIN.If you have not yet assigned a PIN, use the PIN "00000" the first time you enter it.

o Enter the new PIN.

o Repeat the new PIN.

If you forget your PIN, contact the service per-sonnel, who can reset your PIN to "00000".An authorized party can also lock and unlock your telephone.

36

Using Other Functions/Services

Step by Step


Sending a MessageYou can send short text messages (infotexts) to single users or groups of users who have system telephones.On system telephones with no display (e.g. optiPoint 500 entry), on ISDN, pulse or tone dialling te-lephones, transmitted text messages will be saved as a callback request.

n Lift the handset.

qjl Enter the code.

o Enter the internal station number of the recipient or group.

d ... m w Select the preprogrammed message (which can be changed by the service personnel). Enter the code. For example:

Deleting Sent Messages

n Lift the handset.

rjle w Enter the code.

0 = Please callback 5 = Fax waiting1 = Someone is waiting 6 = Dictation please2 = Appointment 7 = Please come see me3 = Urgent call 8 = Please make copies4 = Do not disturb 9 = Ready to depart

Texts sent to groups can be deleted only by the originator.

37

Step by Step


Answering MessagesIf you have received any messages, the button "mes-sages/info" will light up. After lifting the receiver you will hear a special dial tone or an announcement.

n w Lift the handset.

rjlg Enter the code. or


This connects you to the sender of the message or the mailbox system.

Using Another Telephone Like Your OwnOther people can temporarily use your telephone for outgoing calls as though it were their own.

n Lift the handset.

qidl Enter the code.

o Enter the other user’s station number.

o w Enter the other user’s telephone lock PIN.


This state is canceled at the end of the call.

Message Waiting

38


Step by Step

Change call number (relocate)You can put your call number on every other available telephone when it is set up (contact the service person-nel).Your previous telephone then receives the old call number of your new telephone. The call number togeth-er with the settings (e.g. programmed keys) of the tele-phone are changed.

Precondition: Your old and new telephone are the first telephones at each connection. The telephone are in idle state.

The following procedure is carried out on the new tele-phone.

n Lift the handset.

qmhem Enter the code.

o Enter your own call number.

o Enter code (telephone lock) Page 36.(This is not necessary if you have not determined a code yet).

rmhem Enter the code.

You can, however, connect your telephone to an-other connection and carry out the procedure.

39

Step by Step


Resetting Services and Functions(System-Wide Cancellation for a Telephone)There is a general reset procedure for activated func-tions. The following functions are canceled, if they were activated:

• Forwarding on• Advisory msg. on• Ringing group on• Hunting group off• Suppress call ID• Waiting tone off• DND on• Ringer cutoff on• Messages received:• View callbacks

n Lift the handset.

rd w Enter the code.

40


Step by Step

Activating Functions for Another TelephoneIf this function has been configured (contact the service personnel), you can turn the following functions on and off for other telephones. This feature is also known as associated service.

• Do not disturb, code: *97/#97 Page 33• Call forwarding, code *11, *12, *13/#1 Page 13• Lock and unlock all phones,

code: *66/#66 Page 35• Group ringing, code: *81/#81 Page 47• Group call,

code: *85/#85 Page 46• Reset services and functions,

code #0 Page 40• Control relay,

code: *90/#90 Page 44• Night service, code *44/#44 Page 30• Timed reminders,

code *65 Page 31

n Lift the handset.

qlg Enter the code.

o Enter the internal number of the telephone for which you want to activate the function.

o w Enter the code – e.g. *97 for DND on – and procedure (if relevant).

Using System Functions from the Outside(DISA: Direct Inward System Access)If this function has been configured (contact the service personnel), you can set up external outgoing calls from outside the system, just like an internal user. You can also activate and deactivate the following functions in your system:

• Reset services and functions,code: #0 Page 40

• Call forwarding, code: *1/#1 Page 13

41

Step by Step


• Lock and unlock all phones, code: *66/#66 Page 35

• Save PIN, code: *93 Page 36

• Send a message, code: *68/#68 Page 37

• Group ringing, code: *81/#81 Page 47• Group call, code: *85/#85 Page 46• Suppress caller ID,

code: *86/#86 Page 33• Open door, code: *61 Page 18• Door opener on/off, code: *89/#89 Page 19• Control relay, code *90/#90 Page 44• Do not disturb, code: *97/#97 Page 33• Speed-dialing, code: *7 Page 19• Associated service, code: *83 Page 41

Precondition: You have a telephone that uses tone di-aling (DTMF dialing) or you can switch your telephone to tone dialing. The telephone is not connected to the system.

o Set up a call to the system. Enter the station number (contact the service personnel).

o Wait for a continuous tone (if necessary switch the tel-ephone to tone dialing), then enter the internal number that has been assigned to you and the associated PIN.

r Enter the code (necessary only if programmed in the system).

o Wait for a dial tone and then enter the code, such as

*97 for Do not disturb on. Make other inputs as necessary; (refer to the operating instructions for pulse and DTMF telephones).

or


You can only execute one function at a time, or set up only one outgoing connection. The connection is immediately released after successful activation of a function. In the case of an external-external call, the connection is released as soon as either of the parties ends the call.

42


Step by Step

Controlling Connected Computers or Other Programs and Telephone Data Service (For HiPath 3500/3550/3700/3750 only)If this function has been configured (contact the service personnel), you can control connected computers or programs running on them, such as hotel services or in-formation systems, from your telephone.

Precondition: You have set up a connection.

qhfPress the key. LED flashes. Enter the code.

The connected computer now prompts you to enter the data, which you can do in one of two ways. Contact the service personnel to find out which option is pro-grammed in your system:

• Input in en-bloc mode

d ... m Enter data.

r Press this key at the end of the entry.

or • Input in online mode:The connected computer processes your entries di-rectly.

r Enter the code.

d ... m Enter data.

Consultation

43

Step by Step


Controlling RelaysIf this feature is configured (contact the service person-nel), you can turn up to four relays on and off to control different facilities (such as a door opener).Depending on how they are programmed, you can switch the relays on and off or switch them on and have them switched off automatically after a timeout.

n Lift the handset.

qmd or rmd Enter the code for "on" or "off".

e ... h w Enter the relay.

Radio Paging (Not for U.S.)If paging equipment is connected to your system (con-tact the service personnel), you can contact people via their pocket receivers.

The pocket receiver indicates to the person you are looking for that someone is trying to get in touch. The person you page can then go to the nearest telephone and call you.

The operating procedures differ according to the type of radio paging equipment connected (simple or enhanced paging equipment).

Simple Paging Equipment

Paging:

To be paged, you must have activated a call ringing group Page 47, call forwarding Page 13, or call re-direction (service technician) to the internal station number of your paging equipment.A call request is then signaled automatically.


44


Step by Step

Answering the page from the nearest telephone:

n Lift the handset.

qim Enter the code.

o Enter your own station number.

Enhanced Paging Equipment (Hipath 3700/3750 Only)

Paging:

n Lift the handset.

qhi Enter the code.

o w Enter the number of the party you want to page.

Answering the page from the nearest telephone:

n Lift the handset.

rhi Enter the code.

o Enter your own station number.

45

Step by Step

Using Team Functions


Turning Group Call On and OffIf this function has been configured (contact the service personnel), you belong to one or more groups of users who can each be reached under a hunt group or group call number.Incoming calls are signaled on all group member tele-phones in the order in which they are received ( hunt group) or simultaneously (= group call) until one mem-ber of the group accepts the call.You can also belong to a team (including executive/sec-retary ones) to which multiple lines have been as-signed. Page 49.

Each member of the group remains available under his or her own station number.

You can activate and deactivate the audible signal for a hunt group, group call or individual trunks in a group (in-cluding an executive/secretary team).

You belong to a hunt group or a group call:

n Lift the handset.

rli or qli w Enter the code for "leave" or "join".

You belong to multiple groups or to one group with lines (including executive/secretary teams):

n Lift the handset.

rli or qli Enter the code for "leave" or "join".

r w Enter the code for "Leave all groups".

or

q w Enter the code for "Join all groups.

or

o w Enter a group/trunk number to directly "leave or join".


46


Step by Step

Accepting a Call for Another Member of Your TeamYou can accept calls for other telephones in your team from your telephone even while engaged in another call. To do this, contact the service personnel to find out if a pickup group has been configured.

Precondition: You telephone rings briefly.

n Lift the handset.

qik Enter the code.

Activating and Deactivating a Ringing GroupYou can have calls for your telephone signaled audibly at up to five other phones. The person who answers first receives the call.

Saving telephones for the ringing group:

n Lift the handset.

qle Enter the code.

o w Enter the internal station number.

Removing all telephones in call ringing group:

n Lift the handset.

rle w Enter the code.

If you deactivate the audible tone for another group or trunk, or deactivate it for all groups and trunks to which you belong, a special dial tone sounds when you lift the handset.


47

Step by Step


Uniform Call Distribution (UCD)If this function has been configured (contact the service personnel), you belong to a group of users (agents) to whom calls are distributed.An incoming call is always assigned to the agent who has had the longest break without a call.

Logging on and off at the beginning and end of your shift:

n Lift the handset.

qhde or rhde Enter the code for "Log on" or "Log off".

o w To log on, enter your identification number ("Agent:"). Contact the service personnel to find out what it is.

Logging on and off during your shift:

n Lift the handset.

rhdf or qhdf Enter the code for "Not available" or "Available".

Requesting and activating a work time:

If you want to follow-up on the last call you answered without being disturbed, you can request and activate a work time. This removes your telephone from the call distribution cycle for a programmable period of time un-til you log back on.

s or n You have or had an UCD connection.

qhdg or rhdg Enter the code for "on" or "off".

Turning the night service on and off for UCD:

n Lift the handset.

qhdh or rhdh Enter the code for "on" or "off".

48

Team and Executive/Secretary Functions With Assigned Trunk Lines

Step by Step

Team and Executive/Secretary Functions WithAssigned Trunk LinesIf this function has been configured (contact the service personnel), you belong to a team of users for whom special trunk lines exist. You can then conduct your calls as usual via the trunk assigned to you.In addition, you can also activate call forwarding or a ring transfer for the lines of your group.

Forwarding Calls on LinesYou can immediately forward internal or external calls on lines of your group to different internal or external tel-ephones (destinations); even external destinations are possible in certain system configurations.Activating call forwarding for one line activates the func-tion for all members in your group.

n Lift the handset.

qide Enter the code.

o Enter the desired line number.

e or f or g Enter the line type you wish to use:1 = all calls, 2 = external calls only, 3 =internal calls only



n Lift the handset.

ride Enter the code.

o w Enter the desired line number.

If you have activated call forwarding for a trunk, a special dial tone sounds when the line is seized.

49

Step by Step

Testing the Telephone

Transferring Calls Directly to the Exec-utive (Only in an Executive/Secretary Group)Normally, audible signaling of all calls for the executive is heard only in the secretary’s office.You can activate audible signaling so that calls are only signaled on the executive telephone and on a second telephone assigned to it.


n Lift the handset.

qidf Enter the code.



n Lift the handset.

ridf Enter the code.


Testing the Telephone

Testing the Telephone FunctionsYou can test your telephone functions.

Precondition: Your telephone is idle.

n Lift the handset.

qmhd Enter the code.

If everything is OK,• all LEDs on the telephone start flashing, and• the ringer signal sounds.

50

Special Functions in the LAN (PC Network)

Step by Step

Special Functions in the LAN (PC Network)If your telephone is operating in a HiPath 5000 RSM en-vironment, multiple HiPath 3000 systems are intercon-nected via a LAN (Local Area Network, e.g. proprietary PC network). Your telephone calls are conducted via the LAN (PC network).If this is the case, you must take certain special features into consideration when performing various functions. These are described below.

Leaving a Hunt Group/Group CallPrecondition: you belong to the hunt group/group call

Page 46 of another HiPath 3000:

n Lift the handset.

qhk Enter the code.

o Enter the (DISA) call number of the other HiPath 3000.

r Enter.

o Enter the (DISA) call number of your telephone.

r Enter.

rli or qli w Enter the code for "leave" or "join".

You belong to multiple groups of another HiPath 3000:

o Enter the group number for "Join/Leave, directed".

51

Step by Step


Transferring Call Forwarding

You can activate/deactivate call forwarding Page 13 for your telephones from other HiPath 5000 RSM tele-phones.

n Lift the handset.

qhk Enter the code.

o Enter the (DISA) call number of the HiPath 3000 to which your telephone is connected.

r Enter.

o Enter the (DISA) call number of your telephone.

r Enter.


qe Enter the code.

e or f or g Enter the line type you wish to use:1 = all calls, 2 = external calls only, 3 = internal calls only

o w Enter the destination number (without external code).


re w Enter the code.

52


Step by Step

Using Night AnswerIf authorized (contact the service personnel), you can define telephones in other HiPath 3000 communica-tions platforms as the night answer Page 30.

n Lift the handset.

qhk Enter the code.

o Enter the (DISA) call number of the HiPath 3000 to which the night answer telephone is connected.

r Enter.

o Enter the (DISA) call number of the telephone from which you wish to activate/deactivate the night answer service.

r Enter.


qhh Enter the code.

o w Enter the destination number (= temporary night an-swer service) within 5 seconds.


rhh w Enter the code.

53

Step by Step


Activating and Deactivating a Ringing GroupYou can have calls for your telephone signaled audibly at external telephones or at telephones in other HiPath 3000 communications platforms Page 47.

Saving the telephones for the ringing group:

n Lift the handset.

qle Enter the code.

o Enter the call number.

r w Enter.

Removing all telephones in call ringing group:

n Lift the handset.

rle w Enter the code.

54


Step by Step

Controlling RelaysIf this feature is configured (contact the service person-nel, you can also control relays Page 44 in other HiPath 3000 communications platforms.

n Lift the handset.

qhk Enter the code.

o Enter the (DISA) call number of the HiPath 3000 in which the relay is to be controlled.

r Enter.

o Enter the (DISA) call number of the telephone from which you wish to control the relay.

r Enter.

qmd or rmd Enter the code for "on" or "off".

e ... h w Enter the relay.

55

Step by Step


Opening the DoorIf this feature is configured (contact the service person-nel), you can also activate the door opener Page 18 in other HiPath 3000 communications platforms.

n Lift the handset.

qhk Enter the code.

o Enter the (DISA) call number of the HiPath 3000 in which the door is to be opened.

r Enter.

o Enter the (DISA) call number of the telephone from which you wish to activate the door opener.

r Enter.

qje Enter the code.

o w Enter the call number of the entrance telephone.

56

Documentation

57

DocumentationYou can find these operating instructions in the Internet in PDF format under

http://www.siemens.com/hipath

and on CD-ROM (ask the service personnel) in HTML and PDF format.

In order to look at and print the operating instructions in PDF format, you need a computer on which the free Acrobat Reader software package is installed by Adobe.

To look at the operating instructions in HTML format you need a computer with a www browser, e.g. Microsoft Internet Explorer.

http://www.siemens.com/hipath

Fixing Problems

58

Fixing Problems

Telephone Maintenance• Always use a damp or antistatic cloth to clean the telephone. Never

use a dry cloth.• If the telephone is very dirty, clean it with a diluted neutral cleaner con-

taining surfactants, such as a dish detergent. Afterwards remove all traces of the cleaner with a damp cloth (using water only).

• Never use cleaners containing alcohol, cleaners that corrode plastic, or abrasive powders.

Troubleshooting

Pressed key does not respond:

Check whether the key is stuck.

Telephone does not ring:

Check whether the "do not disturb" function was activated on your tele-phone. On lifting the handset, you will hear a special dial tone. If so, deac-tivate it Page 33.

You cannot dial an external number:

Check whether you telephone is locked. On lifting the handset, you will hear a special dial tone. If so, unlock the telephone Page 35.

To correct any other problem:

First contact the service personnel. If the service personnel is unable to correct the problem, contact Customer Service.

Index

Index

Aaccount code .............................................. 32agents .......................................................... 48announcement ........................................... 20answering a timed reminder .................... 31appointment ................................................ 31assigning a DID number ........................... 21associated dialing/dialing aid .................... 22automatic connection setup ..................... 21

Ccall

accepting, group ..................................... 47answering ................................................ 10entrance telephone ................................ 18forwarding ............................................... 13forwarding in a team .............................. 49forwarding MSN in CO .......................... 14parking ...................................................... 24pickup, directed ...................................... 17rejecting ................................................... 17retrieving from park ............................... 25retrieving held ......................................... 25transfer after announcement ............... 28

call charge assignment ............................. 32call signal ..................................................... 10call transfer .................................................. 13call volume ............................................ 10, 16call waiting

accepting ................................................. 23allowing .................................................... 24preventing ............................................... 24

call waiting (camp-on) ................................ 29tone off .................................................... 24

call waiting on/off ....................................... 24call waiting tone on/off .............................. 24

caller IDrestoring display of

suppressing display of caller ID ....... 33caller ID suppression ................................. 33calling a second party ................................ 12calls

distributing ............................................... 48calls in queue .............................................. 48CE mark ......................................................... 2change call number ................................... 39cleaning the telephone .............................. 58conference .................................................. 13connection setup, automatic .................... 21consultation hold key ................................. 12

Ddialing

internal/external calls ............................. 11dialing internal calls .................................... 11dialing numbers

on-hook dialing ........................................ 11using redial .............................................. 12using speed-dialing ................................ 19

direct inward system access (DISA) ....... 41DISA ............................................................. 41distributing calls .......................................... 48do not disturb ............................................. 33door opener ................................................. 19

Eenhanced paging equipment ................... 45entrance telephone .................................... 18executive/secretary functions .................. 49explanation of symbols ............................... 8external code .............................................. 11

59

Index

Fforwarding ................................................... 13

multiple subscriber number (MSN) ..... 14forwarding MSN in CO ............................. 14functions

activating/deactivating for another tele-phone associated service ..................... 41resetting ................................................... 40

Ggroup call ..................................................... 46

Hhandsfree answerback .............................. 17HiPath 5000 RSM

actuators .................................................. 55group call ................................................. 51hunt group ............................................... 51night answer ........................................... 53opening the door .................................... 56relays ........................................................ 55ringing group ........................................... 54transferring call forwarding .................. 52

hotline .......................................................... 21hunt group ................................................... 46

IIP telephony ................................................ 51

Kkeys

fixed ............................................................ 7

60

LLAN telephony ............................................ 51LEDs=light emitting diodes ....................... 7locking

all phones ................................................ 36locking all phones ....................................... 36locking/unlocking the telephone .............. 35

Mmailbox ........................................................ 20making calls

with the dialing aid ................................. 22making external calls ................................. 11making trunk calls ...................................... 11malfunctions ............................................... 58message

answering ................................................ 38deleting/displaying ................................. 37receiving .................................................. 38sending .................................................... 37

monitoringsilent ......................................................... 34

multiple subscriber number (MSN) ......... 14

Nnight answer ............................................... 30notes .............................................................. 2

Oopen door

with a code .............................................. 18open listening ............................................. 10operating principle ....................................... 9operating steps ............................................. 8override .................................................. 29, 34

Index

Pparking a call ............................................... 24personal identification number ................ 36pickup (call) ........................................... 17, 47PIN ................................................................ 36

for a telephone ....................................... 35preventing and allowing automatic camp-on .................................................................. 24programming your telephone ............ 16, 33project calls ................................................. 32

Rradio paging equipment PSE .................... 44recall ............................................................. 28receiving volume .................................. 10, 16redialing a number ..................................... 12relays ............................................................ 44relocate ........................................................ 39reserving a trunk ........................................ 21resetting functions ..................................... 40resetting services ....................................... 40ring tone ...................................................... 16ring transfer

in an executive/secretary team ............ 50ring volume ................................................. 16ringing group ............................................... 47room monitor .............................................. 34

Ssaving a PIN ................................................ 36secretary functions .................................... 49security ........................................................ 33setting your telephone ........................ 16, 33silent monitor .............................................. 34simple paging equipment ......................... 44speaker call ................................................. 20special dial tone .......................................... 20

speed-dialingdialing numbers ...................................... 19saving station speed-dialing ................. 20system ..................................................... 19

station numberassigning .................................................. 21

station speed-dialing ............................ 19, 20suffix-dialing ................................................ 27switches ...................................................... 44system speed-dialing ................................ 19system-wide cancellation ......................... 40

Ttelephone

cleaning .................................................... 58locking ...................................................... 35locking another ....................................... 36locking/unlocking .................................... 35locking/unlocking all phones ................. 36maintaining .............................................. 58operating .................................................... 9settings .............................................. 16, 33testing ...................................................... 50using another like your own ................. 38

telephone data service .............................. 43telephone maintenance ............................ 58telephone test ............................................ 50temporary phone using a

temporary phone .................................... 38testing the telephone ................................ 50testing the telephone functions .............. 50text message

answering ................................................ 38deleting/displaying ................................. 37receiving ................................................... 38sending ..................................................... 37

three-party conference .............................. 13time-dependent hotline ............................. 21toggle ........................................................... 13tone dialing .................................................. 27tone dialing (DTMF dialing) ....................... 27trace call ....................................................... 35transfer (call)

after announcement .............................. 28transfer call .................................................. 13trunk flash .................................................... 28trunk, reserving .......................................... 21

61

Index

UUCD .............................................................. 48using functions from the outside ............ 41

Vvariable call forwarding ............................. 13

Wwork time .................................................... 48

62

Overview of Functions and Codes (Alphabetical)

Overview of Functions and Codes (Alphabetical)The table below lists all available functions. If these functions have been configured (contact the service personnel), they can be called by entering a code or pressing a function key.

Accept a waiting call (camp-on)

Terminate second call,1. Continue the call

Prevent automatic camp-on

Allow automatic camp-on

Call waiting tone on

Call waiting tone off

t n qii(1x or 2x)

n rhmd wn qhmd wn rlk wn qlk w

Accept call, directed

Accept call, group

n qim o Int.

n qikAdjust ring volume

Adjust ring tone

(u or v) e u v simultaneously

(u or v) f u v simultaneously

Answer call nAssign station number (not for U.S.) n qhe o MSN o Ext.

Associated dialing n qjk o Int. w o Stn No.

Associated service n qlg o Int. o

Call charge assignment / account code n qjd o Code r if appl. w o Ext.

Functions Operating Steps

Consultation

Consultation

63


Call forwarding on

Call forwarding off

Forward Line: On

Forward Line: Off

Call forwarding in carrier network on

Call forwarding in carrier network off

n qee o Stn No. w

n qef o Stn No. w

n qeg o Stn No. w

n re w

n qide o Trk No. e o Stn No. wn qide o Trk No. f o Stn No. wn qide o Trk No. g o Stn No. wn ride o Trk No. w

n qjhe o MSN o Ext. w

n qjhf o MSN o Ext. w

n qjhg o MSN o Ext. w

n rjhe w o MSN wn rjhf w o MSN wn rjhg w o MSN w

Call waiting (camp-on) n o Int. w Stn busy; wait 5 seconds

Change call number n qmhem o own call No.

o Code rmhemChange call volume s (u or v) u v simultaneously

Changeover on (lock)

Changeover off (unlock)

Lock all phones

Unlock all phones

n qjj o Code

n rjj o Code

n qmhg o Int. qn qmhg o Int. r

Consult

Quit consultation,1. Continue the call

Toggle

Start three-party conference

Connect parties

s o Stn No.

(1x or 2x)

qf qg

t


Consultation

Consultation

Consultation

Consultation

64


Control relay on

Control relay off

n qmd (e...h) wn rmd (e...h) w

Conversation (entrance telephone)

Open door

Door release on

Door release off

n or after 30 seconds n o Int.

qje o Int.

n qlm o Int. + Code w (e or f)

n rlm o Int. w

DND on

DND off

n qmk wn rmk w

DTMF dialing/Tone dialing s qig oEnding a call t or

Group call, leave

Group call, join

n rli or

n rlir or

n rli o Group

n qli or

n qlir or

n qli o Group

Hotline nMaking calls n o Stn No. or o Stn No. nMonitoring (only U.S.) n qmhh o Int.

Mute off

Mute on

s

s

Night answer on

Night answer off

n qhh o Int. w or

n qhhq w

n rhh wOverride Stn busy qjf w


Consultation

Consultation

Release

Mute

Mute

Consultation

65


Paging another person (not for U.S.)

Answer page(simple paging equipment)

Answer page(enhanced paging equipment)

n qhi o Int. w

n qim o Int.

n rhi o Int.

Park a call

Retrieve parked call

s qij

(d...m) w tn rij (d...m)

Phone test n qmhdPicking up (retrieving) a held call n qjg o Line No.

Redial n

Reject call

Reserve trunk

When the reserved trunk is free

n o Busy (external); wait 5 seconds tn o Ext.

Reset services n rd wRing transfer on

Ring transfer off

n qidf o Line No. wn ridf o Line No. w

Ringing group on

Ringing group off

n qle o Int. wn rle w

Room monitor on

Room monitor off

Monitoring a room

n qll w s

tn o Int.

Save timed reminder

Delete timed reminder

Accept timed call

n qhj o (Time, e.g. 0905) w

n rhj w

n t

Saving a PIN n qmg o Old code o 2x new code


Consultation

Redial

Release

66


Send message

Delete message (sent)

Accept message

n qjl o Int. (d...m) w

n rjle w

n w rjlgSpeaker call

HF answerback

n qld o Int. w

n

Start conference

The other party does not respond1. Continue the call

Add a party to the conference(max. five)

Leave conference

Remove party

Remove ISDN central office partyfrom the conference (only for U.S.)

n o Stn No.

o Stn No. qg

(1x or 2x)

o Stn No.

qg etc.

t

rg qhme

Store a callback

Delete callback

Accept callback

n ril w

n

Suppress caller ID on

Suppress caller ID off

n qlj wn rlj w

Telephone data service s qhf oTrace call (not for U.S.) s qlhTransferring a call

...after announcement to group

s o Stn No. ts qldo Group w s

Trunk flash s qie o


Consultation

Consultation

Consultation

Consultation

Consultation

Consultation

Consultation

Callback

Consultation

Consultation

Consultation

Consultation

Consultation

67


UCD

Log on at beginning of shift

Log off at end of shift

Log off work

Log on work

Work time on

Work time off

Night answer on

Night answer off

n qhde o Code w

n rhde w

n rhdf w

n qhdf w

(n or s) qhdg w

(n or s) rhdg w

n qhdhq w

n rhdh w

Use speed-dialing

Speed-dialing: store station

n o

(*0...*9 or 000...999) or

n qk o (*0...*9 or 000...999)

n qmf o *0...*9 w o Ext. w

Using another phone temporarily n qidl o Int. o Code wUsing mailboxes n w rjlg or

n w


Speed-dial

Message Waiting

68

FCC and Industry Canada Compliance

FCC and Industry Canada ComplianceThis section describes the requirements for compliance with Federal Communications Commission (FCC) Rules and Industry Canada CS-03 standard.

FCC Certification and RequirementsThe following paragraphs describe requirements and information based on FCC rules.

Service

If you experience problem with the Siemens optiPoint telephone, contact Siemens cus-tomer support at 1-800-835-7656 for information on service and repairs. The telephone company can ask you to disconnect the equipment from the network until the problem is corrected or until you are sure that the equipment is not malfunctioning.

FCC Rules, Part 15

The Siemens optiPoint telephone has been tested and complied with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequen-cy energy and, if not installed and used in accordance with the instruction manual, can cause harmful interference to radio communications. Operation of this equipment in a res-idential area is likely to cause harmful interference, in which case the user will be required to correct the interference in the user’s expense.

FCC Rules, Part 68

FCC Part 68 CertificationThe Siemens optiPoint telephone is certified with FCC under Part 68 as a component de-vice for connection behind FCC Part 68 certified Siemens PBX systems. In order for the FCC certification of the Siemens optiPoint telephone to be retained, all other products used in conjunction with the Siemens optiPoint telephone must also be FCC Part 68 certi-fied for use with the front-end terminal equipment. If any of these components are not cer-tified, Siemens is required to obtain FCC Part 68 certification of the assembled equipment prior to connection to the telephone network. Part 68 certification requires Siemens to maintain this approval and as such are responsible for the following:

– Any component added to the Siemens optiPoint telephone, whether it bears compo-nent certification or not, will require a Part 68 compliance evaluation. Siemens may need to test and make a modification filing to the FCC before that new component can be used;

– Any modification/update made to the Siemens optiPoint telephone will require a Part 68 compliance evaluation. Siemens may need to test and make a modification filing to the FCC before that modified component can be used;

– Siemens optiPoint telephone complies with and will continue to comply with all the applicable rules and regulations in Subpart D of the FCC Part 68 rules during the life-time of the product.

69


If at any time the ownership of Siemens optiPoint telephone is transferred to someone else (whether independently or as part of a system), please supply this manual to the new owner.1. REN

The ringer equivalence number (REN) is used to determine the quality of devices which may be connected to the telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all ar-eas, the sum of RENs should not exceed five (5.0). At the base of the telephone is a label contains, among other information, the REN and the FCC certification number. If requested, this information must be given to the telephone company. To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company.Note: REN is associated with the analog telephones. It is not applicable to SiemensoptiPoint telephone. If requested, please supply the FCC Certification numbers of the front-end host terminal equipment that have a direct Public Switched Telephone Net-work connection (i.e. have a REN stated on the label) and the highest REN.

2. Facility Interface InformationSiemens optiPoint telephone connects to the public switched telephone network through FCC Part 68 certified front-end host PBX equipment which specifies the type of network jacks to be used.

3. Disruption of the NetworkIf the Siemens optiPoint telephone disrupts the telephone network, the telephone company can discontinue your service temporarily. If possible, the telephone company will notify you in advance. If advance notice is not practical, they will notify you as soon as possible. You are also informed of your right to file a complaint with the FCC.

4. Telephone Company Facility ChangesThe telephone company can make changes in its facilities, equipment, operations, or procedures that can affect the operation of your equipment. If they do, you should be notified in advance so you have an opportunity to maintain uninterrupted telephone ser-vice.

5. Hearing-Aid CompatibilityTelephones for emergency use and telephones installed in common areas such as lob-bies, hospital rooms, elevators, and hotel rooms must have handsets that are compat-ible with magnetically coupled hearing aids. Persons who are not in common areas must also be provided with hearing-aid compatible handsets, if needed.The Siemens optiPoint telephone complies with the FCC Rules, Part 68, Section 68.316 Hearing Aid Compatibility and 68.317 volume control requirements.

6. Programmed Dialer FeaturesWhen you program emergency numbers or make test calls to emergency numbers us-ing Siemens products with programmed dialer features, stay on the line and briefly ex-plain to the dispatcher the reason for the call before hanging up. Perform these activi-ties in off-peak hours, such as early morning or late evening.

70


Equipment Attachment LimitationsThe following are notices required by Industry Canada Terminal Attachment Program Cer-tification Procedure CP-01, Part I, Section 14.

Ringer Equivalence Number (REN)

The Ringer Equivalence Number (REN) assigned to each terminal device provides an indi-cation of the maximum number of terminals allowed to be connected to a telephone inter-face. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. The REN is associated with the analog loop-start and ground-start tele-phones. It is not applicable to Siemens optiPoint telephones.

Equipment Attachment Limitations

The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirement documents. The Department does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be in-stalled using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some sit-uations.

Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to dis-connect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are con-nected together. This precaution may be particularly important in rural areas.

DANGER

Users should not attempt to make such connections themselves, but should con-tact the appropriate electric inspection authority, or electrician, as appropriate.

71

© Siemens AG 2004Information and Communication NetworksHofmannstr. 51 • D-81359 München

Ref. No.: A31003-H1012-C120-5-7619

Subject to availability. Right of modification reserved. Printed in the Federal Republic of Germany.24.05.2004

www.siemens.com/hipath

The information provided in this document contains merely general de-scriptions or characteristics of performance which in case of actual use do not always apply as described or which may change as a result of fur-ther development of the products. An obligation to provide the respective characteristics shall only exist if expressly agreed in the terms of contract.

hipath 3000 hipath 5000 rsm optipoint 500 entry

Documents