hil-std-431d 16 september 1986 superseding mil-std-431c …
TRANSCRIPT
HIL-STD-431D16 September 1986SUPERSEDINGMIL-STD-431C28 JU~y 1981
MILITARY STANDARD
COMPRESSORS: CONSTRUCTION, PAINT SPRAY, ANDGARAGE; CLASSIFICATION OF TYPES, CLASSES,
STYLES, GROUPS, AND CAPACITIES
.
IFSC 43101
DSSTRIWTION STATEMENT A. Approved for public release; distribution isunlimited.
AMSC B1/A
Downloaded from http://www.everyspec.com
MIL”STD-431D
DEPARTMENT OF DEFENSEWashington, DC 20301
COMPRESSORS: CONSTRUCTION, PAINT SPRAY, ANDGARAGE; CLASSIFICATION OF TYPES, CLASSES,
STYLES, GROUPS, AND CAPACITIES
1. This military standard is approved for use by all Departments andAgencies o f the Department of Defense.
2. Beneficial conunents(recommendations,additions, deletions) and anypertinent data With may be of use in improving this document should beaddressed to: Commanding Officer (Code 156), Naval Construction BattalionCenter, Port Hueneme, CA 93043-5000, by using the self-addressedStandardization Document Improv~ent Proposal (DD Form 1426) aPPearing at theend of this document or by letter.
ii
Q
Downloaded from http://www.everyspec.com
MIL-STD-431D
Paragraph
Table
1.
1.11.21.3
2*
2.12.22.3
3.
3.1
4.
401
5.
5.15.1.15.1.25.1.3
6.
6.16.26.36.4
I
CONTENTS
SCOPE . . 0 .
Scope .Applicatio~ gu~dan~eClassification .
REFERENCED DOCUMENTS
Government documentsOther publicationsOrder of precedence
DEFINITIONS . ● ,
Capacity . . .
GENERAL REQUIREMENTS
Compressor capacity
DETAILED REQUIREMENTS
.
.●
●
✎
●
●
✎
✎
✎
✃
✎
●
Compressor classificationConstruction applicationPaint spray applicationGarage application .
NOTES . . 0 . .
Intended use . ●
Applicable documen~s .
.
●
●
●
✎
✎
●
●
✎
●
●
●
✎
●
✎
●
●
✎
✎
●
.
.●
✎
✎
✎
✌
●
✎
●
✎
●
✎
✎
●
9
●
●
.
●
Subject term (key word) listingChanges from previous issue .
TABLE
Compressor classification .
.
.●
✎
✎
●
✌
✎
✎
✎
●
✎
●
✎
●
●
✎
✎
●
✎
✎
✎
. .
.
●
●
●
●
☛
✎
●
●
✎
✎
●
●
✎
✎
●
✎
●
✎
●
●
●
●
✎
✎
✎
●
●
✎
●
✎
✎
✎
●
●
✎
✎
✎
●
✎
●
✎
✎
✎
w1
111
2
222
2
2
2
2
2
2223
3
3344
. . 3
.0.
1.11 c
Downloaded from http://www.everyspec.com
MIL-STD-431D
1. SCOPE
1.1 Scope. This standard reflects agreements of the Army, Navy, and theAir Force to limit the types, classes, styles, groups, and capacities of aircompressors for construction, paint spray, and garage use to be procured foruse by the respective military departments.
1.2 Application guidance. All construction, paint spray, and garage useair compressors procured after the effective date of this standard shall be ofthe types, classes, styles, groups, and sizes (capacities) listed in thisstandard. This standard does not apply to:
a. Compressors already in the military supply system purchasedprior to the effective date of this standard.
b. Compressors for construction use in which continuing procurementby an activity of specific types and capacities not coveredherein has been authorized as a means of effectingstandardization and interchangeabilityof replacement parts.
c. Self-propelled, tractor-compressorunits.
1.3 Classification. Air compressors covered by this standard shall be ofthe following classifications (see 5.1):
Type I - Reciprocating.Type II - Rotary.
Group a - Single stage.Group b - Multi-stage.
Style A - Electric motor driven.Style B - Gasoline engine driven.Style C - Diesel engine driven.
Class 1 - Tank mounted.Class 2 - Handtruck or wheelbarrow type mounted.Class 3 - Caster mounted.Class 4 - Skid mounted.Class 5 - Trailer mounted.
Size - Capacity in cubic feet per minute (cfm) at sPecified”discharge pressure in pound-force per square inch gage(psig) (see Table I).
(Example: size 250 = 250 Cfm at 100 psig.)
Downloaded from http://www.everyspec.com
MIL-STD-431D
2. REFERENCED DOCUMENTS
2.1 Government documents. (Not applicable).
2.2 Other publications. The following documents form a part of thisstandard to the extent specified herein. Unless specified, the issue of thisdocument which are Department of Defense (DoD) accepted shall be those listedin the issue of the DoD Index of Specifications and Standards (DODISS)specified in the solicitation. The issue of documents which have not beenadopted shall be those in effect on the date of the cited DODISS.
AMERICAN SOCIETY Oi?MECHANICAL ENGINEERS (ASME)
ASME PTC 9 - Displacement Compressors, Vacuum Pumps and Blowers.
(Application for copies should be addressed to the American Society ofMechanical Engineers, United Engineering Center, 345 East 47th Street, NewYork, NY 10017.)
(Non-Government standards and other publications are normally availablefrom the organizations which prepare or which distribute the documents. Thesedocuments also may be available in or through libraries or other informationalservices.)
2.3 Order of precedence, In the event of a conflict between the text ofthis standard and the references cited herein, the text of this standard shalltake precedence.
3. DEFINITIONS
3.1 Capacity. For purposes of this standard, the capacity of acompressor is defined as the volume rate of air flow compressed and deliveredat the specified discharge pressure when the volume rate is expressed asconditions of total.temperature, static pressure, and specified weightprevailing at the compressor inlet.
4. GENERAL REQUIREMENTS
4.1 Compressor capacity. Compressor capacities at specified dischargepressures shall be in accordance with table 1 and shall be as determined bythe ASME PTC 9.
5. DETAILED REQUIREMENTS
5.1 Compressor classification. Air compressors covered by this standardshall be of the types, groups, styles, classes, and sizes (see ]..3)inaccordance with table I and shall be under one of the following applications.
5.1.1 Construction application. Compressors under this application areused as portable sources of air supFly in constructionproject.
5.1.2 Paint spray application. Compressors under this application areused as sources of air for spraying paint.
Downloaded from http://www.everyspec.com
5.1.3garage and
MIL-S’l’D431D
Garage application. Compressors under this application aL*eused inshop work.
TABLE I. Compressor classification.
lSize/Capacity Type Group Style Class ‘1Discharge
1 (cfm) Pressure (Psix)I
I Construction Application 1
I 125 I, 11 a, b B, c 4, 5 100 I
I 250 I, 11 a, b B, C 4, 5 100 1
I 365 I, 11 a, b c 4, 5 100 1
I 600 I, II a, b c 4, 5 100 I
I 7s0 1, 11 a, b c 4, 5 100 I
I Paint Spray Application II 1.5 I, 11 a, b A, B 1, 2, 4 50 II 2.7 1, II a, b A, B 1, 2, 4 80 I
I 15 I, II a, b A, B 1, 2, 4 80 1I 30 I, II a, b A, B 1, 2, 4 80 I
I 75 I, II a, b A, B 1, 2, 4 80 —1
I Garage Application
I 5 I, II a, b A, B 1, 2, 3 1/3
I 8 1, II a, b A, B 1, 2, 3 175 !
I 15 I, 11 a, b A, B 1, 2, 3, 4, 5 175 I
I 25 I, II a. b A,B. 1, 2, 3, 4, 5 175 I
—1--- 1
6. NOTES
6.1 Intended use. The intended use of this standard is to limit thetypes, groups, styles, classes, and sizes (capacities) of air compressors tobe procured by the Army, Navy, and the Air Force.
6.2 Applicable specifications. The following military specifications
shall conform to the classification specified in this standard.
a. MIL-C-555 -
b. MIL-C-3925 -
c. MIL-C-13874 -
d. MIL-C-52980 -
e. MIL-C-82086 -
Compressors, Air, Reciprocating and Rotary,Diesel Engine Driven.Compressors, Reciprocating and Rotary, Power Driven,Air, (Paint Spray Type).Compressors, Reciprocating and Rotary, Air, ElectricMotor Driven.Compressor, Reciprocating and Rotary, Gasoline EngineDriven, Air.Compressor UniLs: Diesel Engine Driven (CommercialType).
Downloaded from http://www.everyspec.com
.
6.3
6.3
MIL-STD-431D
Subject term (key word) listing.
Compressor, reciprocatingCompressor, rotaryConstruction applicationDiesel engine drivenGasoline engine drivenElectric motor drivenGarage applicationPaint spray application
Changes from Previous issue. Vertical lines or asterisks are not usedin this revision to identify changes with respect to the previous issue due toextensiveness of changes.
.Custodians: Preparing Activity:
Army - ME Navy - YDNavy - YDAir Force - 99 (project 431O-O17O)
Review Activities:
Army - AVNavy - MC
User Activity:
Navy - CG
4
Downloaded from http://www.everyspec.com
lNSTRUCTI ONS: In a continuing effoti to make our standardization documenti better, the DoD provides this form for use in;ubmitting comments and suggestions forimprovemen~.Allusersofmilitarystandardi-tiondocumentiareinvitedtopnavid~wgge~tionc.‘1’hioformmay bedetached,foldedalongthelinesindicated,tapedalongthelooseedge(DONOT STAPLE],●lrnajled.Inblock 5, be as specific as pwsible about pmiculm problem -em such M wording whichrequind interpretation. wastoo rigid, restrictive, loose, ambiguous, or was incompatible, and give proposed wording changes which would allevia~ theproblems. Enterin block 6 any remarks not related to a specific paragraph of the document. Ifblock 7 is filled out, ansckno wledgement w“ll be mailed to you within 30 days to let you know that your comments were received and are being ‘considered.
.!+JOTE:This formmay notbe used to request copies of documenti, nor to request waivers, deviations, or clarificatw]l [Jspecification requirements on cument contracta. Comments submitted on this form do not constitute or imply authorizationto waive any portion of the referenced document(s) or to amend contractual requirement
——.—. . .. . . ——(Fold along thu line;
(Fold along thi$ line)—-.. . —
DEPARTMENT OF THE NAVY
11111I
It 4
)FFICIAL BUSINESS‘E NALTY FOR PRIVATE USE $300 BUSINESS REPLYMAIL
FIRST CLASS PERMIT NO. 12503 WA Sh, fUGTON D C
POSTAGE WILL BE PAID BY THE DEPARTMENT OF THE NAVY
CommanderNaval Facilitj,’sEngineering Command (FAC 04?12C)200 Stoval 1 StreetAlexafidria, I’A 22332
— -— ... . ..NO POSTAGE. -1
NECCSSA$3VIF MAILED
IN TNFUfvllkn STA? ES
Downloaded from http://www.everyspec.com
—
STANDARDIZATION DOCUMENT IMPROVEMENT PROPOSAL(See Instructions - Reverse Side)
1. DOCUMENT NUMBER 2. DOCUMENT TITLE
13a. NAME OF SUBMITTING ORGANIZATION
b. AODRESS (Street. City, State. ZIP Code)
5. PROBLEM AREAS
a Paraoraph Number snd Wording:
b.
f’.
Rocomrnonded We-ding:
Ramon/Rationale for Rocommondmion:
0. TYPE OF ORGANIZATION (Marh one)
•1 VENDOR
c1 USE R
•1 MANUFACTURER
c1 OTHER (SR8cify):
i. REMARKS
7a. NAME OF SUBMITTER (Loet, F’irst, Ml) – Optional b. WORK TELEPHONE NUM6ER (Xnclu&code) - Optional
:. MAILING ADORESS (Strvet, City, State, ZIP Code) - Optional 8. OATE OF SUBMISSION (YYMMDD)
DD FORM 1426 PREvIOUS EDITION IS OBSOLETE.82 MAR
Downloaded from http://www.everyspec.com