For More Information & Accessories,Visit our Website - www.LetsGoAero.comContact Us at 877-474-2376 or 719-630-3800 | Email Support@LetsGoAero.com

HOMANUAL 052517

HideOut Package™

Covered Bicycle Storage and Transport Accessory SystemPart No. H01564

PARTS LIST QTY. DESCRIPTION A 1 V-BASE B 2 HORIZONTAL LEG C 4 LOCK NUT D 4 HEX BOLT E 2 WIRE LOCK PIN F 4 SMALL COTTER PIN G 2 WING H 4 UPPER WHEEL CRADLE J 4 LOWER WHEEL CRADLE K 8 RUBBER STRAPS L 4 FOAM CUSHIONS M 2 CAM BUCKLE STRAP

1/2” (13mm) WRENCH

REQUIRED TOOLS:

J

F

E

D

A

B

H

K

G

L

MC

STEP 2

STEP 1

Attach Adjustable Rubber Straps [K] to the Upper Wheel Cradles [H] and Lower Wheel Cradles [J] With the hammerhead end facing away Peg. [DETAIL 2]To attach Cradle Assembly [H] to Wing [G], remove Small Cotter Pin [F], insert through hole, and reattach Small Cotter Pin [F] as shown in [DETAIL 3].NOTE: Foam Cushion [L] position is not fixed. You can Cushions on Wing [G] to expose additional holes.

Where you choose to attach each cradle assembly will depend on the size and shape of the bicycle(s) to be transported. Attach one Upper Cradle assembly [H] to each side of each Wing [K] (two cradle assemblies per wing).Loosen and slip two Lower Wheel Cradles [J] onto the Wing [G] from below the Foam Cushions [L] with each Peg matching the direction of the Upper Cradle Assemblies [H] as Shown [DETAIL 4].

WARNING: ALWAYS MAKE SURE EACH

CRADLE ASSEMBLY IS HELD IN PLACE WITH A SMALL COTTER PIN

[F] AS SHOWN IN DETAIL 3.

DETAIL 1

Connect the V-Base [A] to the Horizontal Legs using 13 mm Hex Bolts [D] and 13 mm Lock Nuts [C] as shown [Detail 1].

A

K

H

C

D

DETAIL 2 DETAIL 3

KK

G

J

H

F

F

LDETAIL 4

J

G

H

STEP 3

Install Wing [G] onto V-Base [A] using Wire Lock Pin [E].

Open wire lock pin [E] as shown in DETAIL 7. Insert wire lock pin [E] through the interior hole at the end of the Wing [G] and out the exterior side of the carrier. (You may need to slide Wing [G] up slightly to align the holes). Close Wire Lock Pin [E] by positioning the loop end of the wire over the pin and allowing it to spring back against the Wing [G] as shown in DETAIL 7.

Install the remaining Wing [G] using the remaining Wire Lock Pin [E].

D

A

G

E

E

E

DETAIL 5 DETAIL 6

DETAIL 7

ONE YEAR LIMITED WARRANTYLet’s Go Aero warrants this product to be free from defect in material and workmanship for one year (retain your sales re-ceipt for your records). Any product or part thereof found to be defective within that period will be replaced without charge provided that: (1) the product was not misused; (2) no alterations or modifications were made; (3) its failure was not a result of normal wear expected in the use of the product; (4) the product or part is delivered, freight prepaid, to Let’s Go Aero. Manufacturers only obligation shall be to replace such products or parts proved to be defective. A Return Merchan-dise Authorization is required prior to return. Please contact Let’s Go Aero toll-free, at 877-464-2376 or 719-630-3800, or via email to support@letsgoaero.com to get an RMA number. This warranty terminates if a purchaser transfers the product to any other person. No warranty is given for LGA products purchased outside of the United States and Canada.

To register your product, visit the Let’s Go Aero website at www.LetsGoAero.comFor assistance with this product, please contact Let’s Go Aero:4474 Barnes Rd, Colorado Springs, CO 80917

Phone: 877-464-2376 or 719-630-3800Email: Support@LetsGoAero.com

To learn more about our line of bicycle carriers for vehicle, home storage, and accessory options for carrying fat bikes, snowboards/skis, and more, be sure to visit our website: www.LetsGoAero.com

U.S. Patent No: D717716; D717717; D684917; 8,889,456; D722289; Patents Pending

WARRANTY STATEMENT

For More Information & Accessories,Visit our Website - www.LetsGoAero.comContact Us at 877-474-2376 or 719-630-3800 | Email Support@LetsGoAero.comCopyright © 2017 Lets Go Aero Inc.

CARRIER INSTALLATION [CARGO RACK NOT INCLUDED]

STEP 1:Install Foam Cushions [L] on ends of Horizontal Legs [B] as shown. [DETAIL 8 & 9]

STEP 2:Center and place the BikeTree inside the Carrier with the Horizontal Legs [B] running perpendicular to the length of the carrier. [DETAIL 10 & 11]

STEP 3:Remove the End Cap and the highest Upper Wheel Cradle [H] located at the top of each Wing [G]. On the inside of the Wing, slip the looped Connection End of the Cam Buckle Strap [M] around the Wheel Cradle and reconnect the Cradle with Cotter Pin [F]. Reinstall End Cap over Cam Buckle Strap [M]. Complete for both Wings. [DETAIL 12 & 13]

STEP 4:Connect the S-Hook End of the Cam Buckle Strap [M] to the Carrier’s provided tie down position with the S-Hook facing away form the carrier. Using the Slack Side, fully tighten Cam Buckle Strap [M] evenly on both sides to remove shifting. [DETAIL 14 & 15]

PRESS

Connection Side

Slack Side

M

S-HOOK CONNECTION MUST ALWAYS FACE THE EXTERIOR OF THE CARRIER AS

SHOWN. [DETAIL 14]

FAILURE TO USE THE CONNECTION SIDE OF THE CAM BUCKLE STRAP [M] WHEN SECURING THE WINGS TO THE

CARRIER MAY RESULT IN LOSS OR DAMAGE PRODUCTS AND/OR PERSONAL INJURY

WARNING:

WARNING:

L

M

G

BL

DETAIL 8

DETAIL 10

DETAIL 12

DETAIL 14

DETAIL 11

DETAIL 13

DETAIL 15

DETAIL 9

HF

ATTACHMENT OF BICYCLES

Reffer to STEP 2 for proper Cradle and Wing Assembly. Lift the bicycle and hang it on the Upper Wheel Cradles [H] with the drive-train of the bicycle facing away from the rack for a closer fit. Secure each Wheel to Upper Cradles with the top side of the tire centered on the cradle as shown [DETAILS 16].Loosen and adjust the Lower Wheel Cradles [J] until they are flush and resting against the bottom of the tire [DETAIL 17]. [Removing the Wing [G] and rearranging the Upper and Lower Wheel Cradles may be necessary depending on your bicycles size and style.] Once the Cradles have been fit to size, stretch the Adjustable Rubber Straps [K] over the tire and reconnect to the hole position that is one hole tighter than necessary with the wheel sandwiched at the end of the Cradle Peg away from the Wing [G] [DETAIL 18].Note: Bike Tire can be adjusted in and out to remove contact with the BikeTree Rack. The Foam Cushions [L] should be positioned as necessary for added protection to the finish of the bicycle. To attach a second bicycle follow the same procedure using the two remaining Upper and Lower Wheel Cradles attached to the back side of the Wings. Position the second bicycle with the handlebars towards the back of the first bicycle.

BICYCLEWHEEL

BICYCLEWHEEL

IMPORTANT FOR SAFETY! AFTER ATTACHING BIKETREE AND BICYCLE(S), BUT BEFORE DRIVING THE VEHICLE,

DOUBLE CHECK ALL POINTS OF ATTACHMENT TO BE SURE THAT THEY ARE TIGHT AND SECURE!

WARNING:

K

K

KJ

H

DETAIL 16

DETAIL 17 DETAIL 18

H

Assembly and Installation:Unfold your BossHog HideOut Cover and drape over top of your BossHog Carrier, assembled BikeTree, and customer supplied bicycles. Fit the thick Waist-Band of the HideOut Cover snuggly over the corners of the carrier. Locate the adjustable Release Buckle underneath the velcro Storm Flaps and tighten the Waist-Band until taut around the carrier. Once the Waist-Band is secured, tighten and connect the 2nd Horizontal Support Strap located above the Waist-Band. Pull the Vertical Support Straps around the underside of the carrier and back to meet at the top. Connect the Release Buckle and pull tight to secure your HideOut Cover and cargo to the carrier.

Unfold the included DragNet and drape over top the secured HideOut Cover. Fasten all Molded Clips by securing and evenly spacing them to anchor points located on the underside of the carrier.

Daily Operation:Remove your DragNet and completely loosen and disconnect all Release Buckles except for the Waist-Band. Locate the Coiled Zipper spanning along the top of the HideOut Cover and unzip. Remove or store any needed cargo or Bicycles, re-zip the HideOut Cover, and reconnect and tighten all release buckles. Reconnect DragNet.

HideOut Cover & DragNet devices are a weather-resistant (not water-proof) cargo protectant

system, and not a cargo restraint.

Be sure to remove your DragNet and completely loosen and disconnect all

HideOut Cover Release Buckles first before removing the Cover off your cargo carrier to

avoid damage to your product.

WARNING WARNING

PARTS LIST

Qty Description

1 HideOut Cover

1 DragNet Cargo Netting With Clips

Always check that HideOut Cover, DragNet & stored cargo are fully secured to the carrier before transit to avoid loss or damage to your product & cargo. Multiple tie-down and strap positions are located along the BossHog Cargo Carrier for supplemental ratchet and tie-down restraints when

necessary.

WARNING

HIDEOUT COVER & DRAGNET INSTALLATION