heat roller unit - teamnisca.com · the unit consists of change path block,card transport block,...
TRANSCRIPT
Heat Roller Unit
PR5302
Service Manual
Ver.1.1 Jan.'10
Heat Roller Unit Service Manual
Contents Section 1 Explanation of the unit Section 2 Installation Section 3 Maintenance Section 4 Exchange of parts and adjustment Section 5 Trouble Shooting Section 6 Parts List
Section 7 Sheets of details
1-1
Section 1 Explanation of the unit
1.1 Outline of the unit
1.1.1 Explanation of the unit
This unit is a Heat Roller Unit to be connected to full color card printer
and to print the heat transfer ribbon (hologram ribbon, reinforced protec-
tive overcoat ribbon) on the printed surface of plastic card. Printing
system is heat transfer printing by halogen lamp energized heat roller.
1-2
1.1.2 Basic specification of the unit
1. Printing system Heat transfer printing by heat roller
2. Print media PVC card (Heat resist type recommended by Nisca)
3. Size of the media Size: 54 x 86 mm
Thickness: 0.76 mm
4. Print area Whole area of the card
5. Printing speed Within 30 sec. ( Warm-up time within 2 min.)
6. Transfer ribbon Protective coating ribbon recommended by Nisca
7. Communication Communication with the printer via RS-422
compatible interface
8. Power source AC power source for heater: AC100/120V 50/60Hz.
AC200/240V 50/60Hz.
* common unit for 100V and 200V series is not
available.
9. Size of the unit 400mm(H) x 180mm(W) x 300mm(L)
10. Weight 10kg or less. (with transformer :13kg or less )
1-3
1.2 Function of the mechanism
The unit consists of change path block,card transport block, heat roller
block, ribbon block,and card ejection block.
① path change block
To change the card path direction to transport a card to heat roller block.
② Card transport block
To transport the card to heat roller block with making the card position
straight.
③ Heat roller block
This block is used to heat transfer printing of heat transfer ribbon (hol-
ogram and protective overlay). Positioning (up and down) of the heat
roller is controlled by cams. For printing of thin ribbon (such as normal
hologram) it is controlled to two positions, printing and retraction.
Printing is done on the platen roller where the ribbon is nipped between
the heat roller and card.
②CARDTRANSPORTBLOCK
③HEATROLLERBLOCK
④RIBBONBLOCK
⑤CARDEJECTIONBLOCK
①CARD PATHCHANGEBLOCK
1-4
④ Ribbon block
Ribbon cartridge consists of supply spool and take up spool. Both spools
are driven via torque limitters for constant tension and transportation
making the stable printing possible.
⑤ Card ejection block
A transparent stacking box is attached to the card ejection exit to stack
the printed cards (up to 100 standard cards). The cards are easily taken
out from the opening located at the back side of the box.
1-5
1.3 Explanation of electrical function
1.3.1 Constitution of the electrical part
Heat roller is controlled and driven by the following parts.
◇ Control board (PBA-CONT) Controls the heat roller unit by the commands received from the printer.
Communication is made via RS-422 compatible interface.
◇ Power source DC+5V and DC+24V are supplied from the printer.
AC100/120V is supplied to the heat roller independently.
◇ Heat roller The heat roller supplies thermal energy to print the protective overcoat
film on the card.
◇ Input/output part This part consists of the motors and sensors to transport the card and
print the coating film.
CPU(IC1)
CommunicationCircuit
Power
Supply
SN1 Sensor InputCircuit
Sensor InputCircuit
SN8 Sensor InputCircuit
SN2
PRINTER
DC24VPGNDDC+5VSGND
Sensor InputCircuit
Sensor InputCircuit
Sensor InputCircuit
Sensor InputCircuit
SN5
SN3
SN6
SN9
SN4
24.57MHz(OSC1)
PM 3
Drive Circuit
Watch DogTimer
(IC2)
EEPROM(IC5)
COVER OPEN SWInput Circuit
ACINPUT
LMP
SW1,2,3
PM1
PM2
PM3
Power SupplyAC120
/240V
+24VPGND+5VSGND
HEAT ROLLER UNIT BLOCK DIAGRAM
PBA-CONT
Sensor InputCircuit
SN7
Sensor InputCircuit
PM 2
Drive Circuit
PM 2
Drive Circuit
1-6
1.3.2 Control circuit board ( PBA-CONT)
This circuit is to control card feeding, card transportation, stop, eject-
ion and printing the coating film on the card, and consists of the input
circuit to receive signals from sensors, switches and control signals from
the printer, output circuit to drive various motors and CPU and its perip-
herals.
(Input circuit)
This is the circuit to input the information form the sensors into CPU
(IC1).
The following is the explanation of each input circuit.
◇ SN1 ( Card feed sensor )
The card feed sensor is a pass-through type sensor with connector,
consisting of an LED and a phototransistor facing each other across the
card path. The card is sensed by blocking the light entering to the
phototransistor from the LED.
Input signals to the CPU are, H for no card and L for card existence.
◇ SN2( Card path change and eject sensor )
Card path change sensor is a pass-through type sensor with connector,
consisting of an LED and a phototransistor facing each other across the
card path. The card is sensed by blocking the light entering to the
phototransistor from the LED.
Input signals to the CPU are, H for no card and L for card existence.
◇ SN3,4( Card path change block position sensor )
This sensor is a pass-through type sensor with connector, consisting of
an LED and a phototransistor facing each other.
A disk with some slit will rotate according with card path change block
rotated. Block position will be detected by Conbination of the level of SN3
and SN4.
◇ SN5 (Heat roller position up sensor)
Heat roller position sensor is a small photo interrupter with connector
using an LED and a phototransistor.
◇ SN6 (Ribbon Supply sensor)
Ribbon empty sensor is a small photo interrupter with connector using an
LED and a phototransistor. A clock disc (disc with slots) rotates as the
ribbon take up motor rotates and the light from the LED is chopped. Exist-
ence of the ribbon is sensed by the chopping signal because the disc will
stops when the ribbon becomes empty.
◇ SN7 (Card detection sensor)
Card detection sensor is a small photo interrupter with connector using an
LED and a phototransistor.
This sensor detects the leading edge of a card.
H:No Card, L:Card is detected.
1-7
◇ SN8 ( Ribbon position sensor )
Ribbon position sensor is a pass-through type sensor, consisting of an LED
a the phototransistor facing each other across the ribbon path. When the
light from the LED is blocked by the mark on the ribbon, light amount ente
-ring the phototransistor decreases and the ribbon is recognized. This
circuit has automatic adjustment function as following:
Light amount of the LED is controlled by adjusting the amount of current
by the DA output of the CPU (IC1). The phototransistor is set at a
specified voltage level, when there is no ribbon, by adjusting the light
amount emitted from the LED. When the ribbon mark comes to the position,
the light is blocked and the voltage level changes beyond the threshold of
the comparator and the ribbon is recognized. Signals to the CPU are, H for
no mark and L for a mark detected.
◇ SN9 (Heat roller surface temperature sensor 1)
Heat roller surface temperature sensor 1 is a bead type thermister for
sensing and controlling the temperature of the heat roller. As the temp-
erature of the heat roller increases, the resistance of the sensor decrea-
ses. As the result, the voltage of the proportional resistance on the cir-
cuit board is increased. This voltage is amplified by ope-amp and input
to the input.
◇ SW1,2,3 (Cover open sensor)
A small high capacity door switch is used to automatically shut off the AC
power supply when the covers are opened and also used as a cover open
sensors. Supply of +24V for the drive circuit will also be shut off by the
above switches. There is a surge protection circuit for the input circuit
and the signal is input through a transistor.
H:Open, L:Close
Output circuit
This is the circuit to drive motors and fans etc. by the signal from CPU
(IC1).
Following is the explanation of each output circuits.
◇ PM1 (Card transport motor)
A hybrid stepping motor is used to transport the card. Card is transport-
ed from the entrance to the exit.
The motor is controlled by the unipolar constant current chopper type 4
phase stepping motor driver circuit.
◇ PM2 (Heat Roll Up/Down, Ribbon winding motor)
A hi-brid stepping motor is used for Heat roll Up/Down and also used for
Winding ribbon.
The function for Heat roll Up/Down or winding ribbon will be changed by
direction of rotation.
◇ PM3 (Path change motor)
A PM type stepping motor is used for changing card path.
1-8
This motor drives the whole card path change block.
Other
Other than mechanical control.
◇ EEPROM (IC5)
This is the memory to store the adjustment data such as level of the pass-
through sensors and card position, and the count data such as the number
of the cards passed the sensor etc. Communication with the CPU is done
through 3 wire serial interface. Stored data is kept even after the power
is turned off.
◇ EPROM (IC4)
This is the memory containing the firmware of the CPU (IC1). It is excha-
ngeable as it is mounted on the IC socket(R38, IC9, 11).
◇ WDT (IC2)
This is the circuit to create the reset signal of the CPU (IC1), consisti-
ng of IC2 and its peripheral circuits.
In the IC2, most of the reset function is compiled such as power-on reset,
abnormal low voltage of the +5V source, and has a watchdog timer function.
1-9
1.3.3 Input/output mechanisms
Mechanical part of the Heat roller unit is composed of sensors and motors.
<Input mechanism>
Symbol Component Function
SN1 Photo sensor Card position detection
(single unit type) (after the card feeding block)
SN2 Photo sensor Card position detection
(single unit type) (before card ejection block)
SN3
Photo sensor
(single unit type)
Path change block position detection. 1
SN4
Photo sensor
(single unit type)
Path change block position detection. 2
SN5 Photo sensor
(single unit type) Heat roller position detection
SN6 Photo sensor Ribbon set detection
(single unit type)
SN7 Photo sensor Card position detection
(single unit type)
SN8 Photo sensor Ribbon empty detection
(separate type)
SN9 Thermister Heat roller temperature sensing
SW1,2,3 Microswitch Detection for Open/Close of the covers
<Output mechanism>
Symbol Component Function
PM1 Pulse motor Card transport from feeding to ejection
PM2 Pulse motor Ribbon take up
Heat roller Up/Down
PM3 Pulse motor Rotating the path change block
Section 2 Installation
2.1 Installation
2.1.1 Caution for installation
Dusty room must be avoided for installing this unit because dust will affect the
print quality due to its printing system. A place where magnetic field emitting
equipment is installed must be avoided for the printing the cards with magnetic
stripe.
General caution for installing OA equipment shall be paid for selecting the
place of installation. Refer to the operation manual for the details.
2.1.2 Space for installation
Secure enough space around the printer and this unit for smooth operation as
shown in the following fig. At least 50cm of space above the unit must be
secured.
The table to install the unit shall meet the following conditions:
◆ The table must be able to bear the weight of the printer and this unit
(approx.26Kg)
◆ The table with a flat top. ( all 8 legs of the printer and this unit must
contact the table top.)
◆ Table top must be kept horizontal ( within 1°of incline).
6in15cm
12in30cm
12in30cm
6in15cm
2-1
3-1
Section 3 Maintenance
3.1 Maintenance list
To keep optimum performance of this unit, Periodical maintenance work will be
required.
In this section, the items which may be performed considering the actual condition
of the customers usage are described including the maintenance by the customer.
Part Maintenance Materials to be used
Rubber roller
◆ Print roller
◆ Other
Same time with printer
( every 10000 frames )
Clean when needed
Symptom: Mall-transportation
→ Troubleshoot
Philips screw driver
Cotton swab
Alcohol
Philips screw driver
Cotton swab
Alcohol
3.2 Maintenance method
Actual method of maintenance is described in this section.
3.2.1 Cleaning of rubber roller
To maintain its performance, this unit uses rubber rollers with high
transportation capability which can easily be cleaned periodically by users with a
certain level of experience. However, it may be heavily
stained and may cause a transportation error if cards with heavy stain or with
special coating are printed. In such case, clean the rollers in the following
method.
(1) Transport roller in the card Path change block
Open the top cover and rotate the card path change block to make rubber rollers
coming up side.
Put a cotton swab with alcohol on the surface of rubber roller then rotate the
Ccard transfer rollers by using grren knob which located at front access block.
(2) Transport roller in the card transport block
Rmove the right side cover, put a cotton swab with alcohol on the surface of
rubber roller then rotate the card transfer rollers by using grren knob which
located at front access block.
Section 4 Exchange of parts and adjustment
4.1 Exchange of Control circuit board (PBA-control)
Step 1. Remove R-cover. ( 6 screws )
Step 2. Loosen 2 screws at bottom and take two screws of at top of main board
bracket.
Lie down the bracket toward back side.
Step 3. Disconnect the connectors of harness of the control circuit board.
(CN1-CN9)
Step 4. Remove control circuit board. ( 6 screws )
Step 5. Pull out EPROM (IC4) on the board with ROM remover and plug into
the new control board. Fix the new control circuit board.
( 6 screws )
Step 6. Connect the connectors to the harness of the new control circuit board.
Step 7. Attach R-cover and fix. ( 6 screws )
Step 8. Turn the power on and set the inside setting of the heat roller unit.
◇ Adjust the sensor level.
◇ Adjust the printing position.
◇ Adjust the heat roller temperature and card transportation speed.
Caution: Turn off the printer (PR5300) and all units connected to it including
PC when performing the above exchange work. Also, plug off the cord
of the heat roller unit. ( It may cause electric shock/trouble.)
CN13 CN3
IC4
CN6
CN1
CN10
CN4CN2CN11
CN5
CN12
PR5302K001*(EPROMクミ)
CN7CN8CN9
4-1
4-2
4.2 Adjustment to be performed when control circuit board is exchanged
4.2.1 Sensor level adjustment
Levels of all sensors of the heat roller unit are adjusted at factory
before shipment. However, they must be re-adjusted in the following cases.
◇ Control circuit board (PBA-control) is exchanged.
◇ Sensor is exchanged. ( Light emitter, receiver )
◇ Mechanical change is done affecting the light path of sensor.
◇ Card jam occurs frequently.
◇ Ribbon related error occurs frequently.
If the output voltage level of sensors can not reach the specified value
in spite of adjusting the them as the following instruction, refer to item 3) and
repair the defective part.
Note: Adjust the sensors at the place where outer light will not affect.
Use the voltage tester with the resolving power of 0.1V or higher if
a tester is used to measure the output voltage of the sensors.
1) Steps to adjust automatic adjustment of the sensor
Step 1. Check that there is no card inside the unit with the power off.
Step 2. Turn the power on. ( continue to further steps even if an error
occurs.)
Step 3. Remove ribbon from the unit.
Step 4. Set the ribbon type to "NO RIBBON TYPE".
Step 5. Select the "H.Roller Check" in Service Mode after initialization.
See the PR5300 Service Manual for operation of sevice mode.
Step 6. Reset the ribbon type to previous type.
The above will complete the automatic adjustment of the sensors.
2) Checking the output of the sensors
The following is the set value and checking point on the control circuit board
for checking the output voltage of the sensors with tester.
◇ SN8 ( detection of the mark on the ribbon )
Checking position: TP38 (SN8AD)
Clear: 1.2V or lower ( at no mark position )
Blocked: 3.8V or higher ( at mark position) Note: The above voltages are against TP4 ( SGND ) on the control circuit board.
CN13 CN3
IC4
CN6
CN1
CN10
CN4CN2CN11
CN5
CN12
PR5302K001*(EPROMクミ)
CN7CN8CN9
Checking position of sensor output ( PBA-CONT )
4-3
4-4
3) Measures for the case where the normal output voltage is not obtained.
If the sensor output voltage as shown in 2) is not obtained, find the defective
part and repair.
Possible defect Check and repair
Defective connection of harness
connecting sensor to the PCB.
Check all connectors connecting the
light emitter and receiver to the
control circuit board.
Use circuit tester and check
connection of all harnesses referring
the circuit diagram. If broken wire
is found, exchange the harness.
Defective mounting of sensor.
Check the mounting condition of both
light emitter and receiver. If loose
screw or incorrect setting is found,
correct it.
Sensor itself is defective.
Exchange the light emitter and
receiver with the normal ones and
check the operation.
Defective control circuit board
Exchange the control circuit board
( PBA-control) with normal one and
check the operation.
4.2.2 Adjusting the print position
Adjust the print position in the following steps after replacing the
control printed circuit board( In case of Hard Coat type ribbon).
Step 1. Turn on the power switch of the printer (PR5300).
Step 2. Get the menu as shown below in the service mode
" H. Roller Check"
Press EXE, The display will be changed as shown below
"Position Adj. "
EXE:Test Print
Press EXE to print test patern.
Check the print position of the overcoat.
A+direction
If there is a shear of print position, adjust it as following:
Step 3. Set the operation panel display to
" Position Adj"
**.
Change the setting values ** by EXE key and CLEAR key.
EXE key : increase value
CLEAR Key: decrease value
The distance A as shown in the following fig. becomes larger by
increasing the value and smaller by decreasing.
The amount of shifting of the overcoat position is :
0.0846mm ( approximately 0.1mm) per one step of change of the
value.
Step 4. Finish the "HeatRoller Check" mode.
Note) Regarding the operation of the operation panel, refer to the
Section 3, " Operating the Operation Panel" of the Service Manual of
the Card Printer (PR5300).
4-5
4.2.3. Adjustment of the print condition
Print conditions (card transport speed, heater temperature etc.) are
adjustable with this unit according to the type of the heat transfer
ribbon. The conditions must be re-adjusted when the control board is
replaced.
Step 1. Turn on the power of this unit while connected to the printer
(PR5300).
Step 2. Set the operation panel display of the printer (PR5300) to:
"H.Roller Ribbon"
***********Type "HARD COAT TYPE" OR "SOFT COAT TYPE"
Set each value for "HARD COAT TYPE" "SOFT COAT TYPE" again.
Step 3. While either one of the above is displayed, press CLEAR key
holding the EXE key pressed. This will set the mode to adjust the
print condition for the corresponding ribbon type.
Operation panel display:
"Heat Adjustment"
Push Menu Key
Step 4. Setting print speed
In the state of the Step 3 above, press MENU key and set to Print
Speed Set mode.
Operation panel display:
"Heat Speed "
Adjustment *
* : Speed set value
EXE key : increase value
CLEAR key: decrease value
Following shows the interrelation of set value and the card
transport speed.
For HARD COAT TYPE : approx. 0.5mm/s per digit.
For SOFT COAT TYPE : approx. 3.0mm/s per digit.
Step 5. Setting the printing temperature
After competing to set the printing speed, switch to the Print
Temperature Setting mode by pressing the MENU key.
Operation panel display:
"Heat Temperature"
Adjustment *
* : Setting value
EXE key : increase value 2 degree C / digit
CLEAR key: decrease value 2 degree C / digit
4-6
4-7
4.3 Exchange of EPROM assembly
Step 1. Remove R-cover. ( 6 screws )
Step 2. Loosen 2 screws at bottom and take two screws of at top of main board
bracket.
Lie down the bracket toward back side.
Step 3. Pull out EPROM (IC4) on the board with ROM remover and plug into
the new control board. Fix the new control circuit board.
( 6 screws )
Step 4. Attach R-cover and fix. ( 6 screws )
Note: Turn off the printer (PR5300) and all units connected to it including
PC when performing the above exchange work. Also, plug off the cord
of the heat roller unit. ( It may cause electric shock/trouble.)
4.4 Exchange of the Heat roller
If the following defects of the heat roller occurs, repair or exchange of
the heat roller in the following steps.
◇ Halogen lamp in the heat roller does not turn on.
◇ Halogen lamp in the heat roller turns on after turning the power switch of
the unit but turns off after about 30 second.
◇ Halogen lamp in the heat roller is turned on but warming up does not
complete after 5 minutes or longer
Possible defect Check and repair
Defective connection of the harness
which connects lamp and powercord,
thermister and control circuit
board board.
Referring the circuit diagram,
check whether each harnesses are
securely connected.
Referring the circuit diagram,
check with tester whether there
is broken harness wire.
Thermister or Lamp or Thermal huse
is defect
Replace the Hotroll unit
The circuit board is defect Replace the circuit board
(PBA-CONT)
Caution: Turn off the printer (PR5300) and all units connected to it including
PC when performing the above exchange work. Also, plug off the cord
of the heat roller unit. ( It may cause electric shock/trouble.)
5-1
Section 5 Troubleshooting
In this section, causes and countermeasures for troubles in heat roller
unit are explained.
5.1 Troubleshooting for troubles displayed on LCD panel
If a trouble in the heat roller unit is detected, error LED on the
operation panel of
the printer turns on and the type of the error is displayed on the LCD
panel.
In this section, cause and the method of recovering from the error is
explained based on the display on the LCD.
◆ The user should do recovery operation following the messages shown on the
LCD panel as the most of the error can easily be cleared by users.
However, if it is not cleared by user in the normal method, or the same
error occurs repeatedly, service person will be called.
◆ When service person call is received, ask the contents of the error
message and detailed error code, and ask the user to explain the detailed
symptom of the trouble.
◆ There are some messages that do not have the detailed error code.
The detailed error code is very important to know the cause of the error.
Error codes relating to the heat roller has H before the 4 digits hexadecimal
number. (ie. H10-01) In this section, detailed error codes are shown by wild
card (**) or two digits of hexadecimal figures.
◆ The numbers in the table in the following section (No.) are for the listing
number of the errors, not detailed error codes.
5-2
5.1.1 Messages on LCD panel and method to recover
(1) Errors in the normal use
These are the errors which occur in the normal usage. These errors are
easily recovered by the users. However, they may be caused by some
troubles of sensors etc. in which case service person has to be called for
checking and repairing.
No. Message on LCD Contents Method of recovery
1
H.Roller Cover
Open H01-**
Cover(s) is (are)
open.
Check and confirm that
the cover(s) is(are)
closed, and press "Clear"key.
H.Roller Ribbon
Empty H02-01
The ribbon is used up
A remaining card will be
continued processing.
2
H.Roller Ribbon
Empty H02-02
The ribbon is used up
A remaining card will be
quited processing.
Set new ribbon and press
"Clear" key.
3
Ribbon type
Incorrect H1B-12
The ribbon setting on the
printer is not same as
actual ribbon
Check wheter the type of the
ribbon maches with the setting
of printer panel.
If it is different, change the
setting of the operation
panel of the printer.
4
Check H.Roller
Power H25-**
The heat roller temperature
does not reach the set
value.
Check whether the power cable
is connected correctly.
5-3
(2) Errors relating to card transportation
If the card is not correctly transported in the heat roller unit as the
sequence, it becomes Card Jam error. The following is the method of
recovering in such case. Card Jam error may also be caused by defective cards
such as out of specification ( size, thickness etc.), bend, surface conditions
( special treatment such as anti-static coating ). Check and confirm if there is
no problem on the card.
No. Message on LCD Contents Method of recovery
Card JAM HR Unit
Area 10 H11-**
Card JAM HR Unit
Area 10 H13-**
Card JAM HR Unit
Area 10 H14-**
Card JAM HR Unit
Area 10 H15-**
A card jam error has
occurred in card path
change block.
Card JAM HR Unit
Area 11 H12-**
A card jam error has
occurred in Heat Roll block
Press "Clear" key. If it does
Not recover, turn off the
power switch and remove the
card by hand by rotating the
knob on the front panel of
the unit.
5
Card JAM HR Unit
Unknown H16-**
A card jam error has
occurred in Heat Roll block
Press "Clear" key. If it does
Not recover, turn off the
power switch and remove the
card by hand by rotating the
knob on the front panel of
the unit.
(3) Errors relating to ribbon transportation
The errors related to taking up ribbon will be occurred when transporting ribbon
process does not meet correct sequense.
In this case, the factor of this kind of erros may depend on a ribbon it self.
Please use correct ribbon.
No. Message on LCD Contents Method of recovery
Ribbon Wind up
Miss H1A-13
There is no ribbon set in
the heat roller. or
The ribbon is not set
correctly.
6
Ribbon Wind up
Miss H1A-13
Taking up ribbon does not
work correctly.
Check and confirm the ribbon
is set correctly and press
"Clear" key. or
Check wheter the type of the
ribbon maches with the setting
of printer panel.
If it is different, change the
setting of the operation panel
of the printer.
5-4
(4) Errors relating to internal problem of the heat roller unit
The following is the errors caused by the internal problems of the heat roller
unit. Almost all of these errors must be checked and repaired by service person.
No. Message on LCD Contents Method of recovery
7
Service Call
Error code H**-**
Unrecoverable error
has occurred on heat
roller unit.
Turn off and on the power
switch.
If the error repeats, service
person has to be called for
check and repair.
5-5
5.1.2 Method of checking and repairing the troubles
For troubles which users can not recover, service person should perform
the check and repair service in the following procedures.
Caution: Read carefully before troubleshooting.
The numbers used in the following explanation (No) accord with the numbers used in
the above table of error messages.
◆ When doing the following works, don't forget to turn off the power switch and
unplug the cord.
・Removing front or rear cover of the heat roller unit.
・Checking connection of the harnesses.
・Exchanging the parts such as printed circuit board, sensors, motors, etc.
・Connecting the cable to the printer.
・Exchanging the heat roller.
◆ Card jam errors are detected by the sensors placed on the card path.
The errors are classified by the block where a card jam has occurred.
◆ If error of sensors with level adjustment occurs frequently, it is
possible that the adjustment of the sensor is not correct. Remove card
and ribbon form the unit and re-adjust the sensors following the instruct-
ions in Section 4.2.1.
"Sensor level adjustment".
Note: Check and confirm that there is no card and ribbon in the unit without
fail.
◆ Follow the instruction of Section 3.2.1, "Cleaning of rubber roller" when
cleaning rubber rollers.
5-6
No. Code Error status Method of checking and repairing
1 H01-** Cover(s) is(are) open. (1) If the sensor is not working
normally, check the connection
of the harness.
・ ASM-I/L-SW
(2) If the connection of the harness
is normal, replace the following:
・ SW1,2,3
・ PBA-CONT SUB
2
H02-01
H02-02
Ribbon marak is detected
while printing
3 H1B-**
Ribbon mark was not detected
when using the ribbon of
which has mark.
(1) Check the type of the ribbon type
setting on the printer.
(2) Adjust the sensor level of SN8.
If it is unadjustable, exchange the
following.
・ PBA-RIBBON PT
・ PBA-RIBBON LD
・ ASM-SENSOR 2
・ PBA-CONT SUB
4
H25-01
H25-02
The heat roller temperature
does not reach the set value
while heat roller warming up
operation.
(1) Check the power source of the
heat roller.
(2) Turn on the power and check if the heat
roller lamp is turned on while display
showing as
"Ready to Print "
H.Roller Warm up.
(3) If the lamp is turned on, it may be
some trouble with thermister.
Check the following items and replace
if neccesary
・ASM-THERMISTER
・ASM-SENSOR1
・PBA-CONT SUB
(4) If the lamp is turned on.
Check the following items and replace
these if neccesary.
・ASM-BK/NF
・ASM-NF/RY (100V series)
・TRN (200V series)
・ASM-HEAT
・HR-FUSE-UNIT
・HR-HLGN-UNIT
・PBA-CONT SUB
・LMP
5-7
No. Code Error status Method of checking and repairing
H11-**
A card jam has occurred in
Card path change block.
The card is stopping at:
SN1 or 2 or 7
H12-**
A card jam has occurred
between Card path cange and
Heat roll blaok.
The card is stopping at:
SN7
H13-**
A card jam has occurred in
Card path change block.
The card is stopping at:
SN2
H14-**
H15-**
A card jam has occurred in
Card path change block.
The card is stopping at:
SN1
5
H16-** Un supposed sensor is
detecting a card.
SN1,2,7
(1) Check the card is stopping at the
sensor.
Make cleaning on card transport rollers
when card is there.
(2) If card jam repeats even after made
cleaning,check the parts of the card
transport drive system.
Replace following parts when PM1 does
not work.
・ASM-MOTOR
・PBA-CONT SUB
・PM1
(3) If there is no card at the position
where specified by error message, it i
s possible that card position sensor do
es not work.
Check the following items and replace
these if neccesary.
・ ASM-SENSOR 2
・ SN1,2,7
・ PBA-CONT SUB
6
H1A-01
H1A-03
Ribbon winding clock is not
generaed.
Or.
Clock is generaed even ribbon
type is set at
“No Ribbon Type”.
(1) Check and confirm the ribbon is set
correctly.
(2) Check wheter the type of the ribbon
maches with the setting of printer
panel.
(3) Check the parts related to ribbon
winding are fixed correctly.
Check the parts themselves of the
ribbon winding drive system (From PM2
to ribbon winding spool ).
If PM2 does not work, check the
following items and replace these if
neccesary.
・ASM-MOTOR
・PM2
・PBA-CONT SUB
(4) The error occurs even ribbon is
transpoted correctly.
Then, it is possible that ribbon clock
sensor is does not work.
Check the following items and replace
these if neccesary.
・ASM-SENSOR 1
・SN6
・PBA-CONT SUB
5-8
No. Code Error status Method of checking and repairing
H1D-**
There is no edge detected
from sensor 1 which located
card path change block.
SN3
7
H1E-**
There is no edge detected
from sensor 2 which located
card path change block.
SN4
(1) Remove the remaing card in the unit.
Then turn power off and on again.
(2) Check the parts themselves of the
card path change drive system (From PM3
to card path change block ).
If PM3 does not work, check the
following items and replace these if
neccesary.
・ASM-MOTOR
・PM3
・PBA-CONT SUB
(3) The error occurs even card path change
block works.
Then, it is possible that sensor which
detects the position of card path
change block does not wrok.
Check the following items and replace
these if neccesary.
・SN3
・SN4
・ASM-SENSOR1
・PBA-CONT SUB
H1F-**
There is no signal detected
from card path position
sensor.
(1) Check the parts themselves of the
H/R drive system (From PM2 to H/R ).
Especialy watch carefully in area of
open cover.
If PM2 does not work, check the
following items and replace these if
neccesary.
・ASM-MOTOR
・PM2
・PBA-CONT SUB
(2) If error occurs even H/R block works.
Then, it is possible that sensor which
detects the position of H/R block does
not wrok.
Check the following items and replace
these if neccesary.
ASM-SENSOR 1
SN5
PBA-CONT SUB
5-9
No. Code Error Status Method of checking and repairing
H20-01
There is a trouble in the
automatic adjustment of
the ribbon mark sensor.
(1) Check the light axis of the sensor.
If the light axis is not correct,then
put the LED or photo transistor at
correct position.
(2) If the sensor is fixed at correct
position, check the following items and
replace these if neccesary.
・PBA-RIBBON PT
・PBA-RIBBON LD
・ASM-SENSOR 2
・PBA-CONT SUB
・
H21-01
The heat roller temperature
does not reach the set value
while heat roller warming up
operation.
(1) The temperature of surface of H/R is
not detected correctly.
Check the thermister is fixed
correctly.
Or
Theremister device does not work
correctly.
Check the following items and replace
these if neccesary.
・ASM-THERMISTER
・ASM-SENSOR 1
・AMS-BK/NF
・ASM-NF/RY
・ASM-RY (100V sries)
・TRN (200V series)
・ASM-HEAT
・HR-FUSE-UNIT
・HR-HLGN-UNIT
・PBA-CONT SUB
H23-** Read/write error occurred
in EEPROM on the circuit
board.
(1) Turn off and on the power.
If the error repeats, exchange
the following:
・PBA-CONT SUB
7
H24-** Communication error with
the printer.
(1) Turn off and on the power.
If the error repeats, exchange
the following:
・ASM-INTERFACE 1
・PBA-CONT SUB
Card Printer PR5302 Parts LISTRef. No. Part No. 部品名 Part Name Qty
B1 020100FWWS SCR-020-100WWS SCR-020-100WWS 3B2 030060FNBI SCR-030-060 SCR-030-060 10B3 030060FPWP SCR-030-060PWP SCR-030-060PWP 1B4 030060FWNB SET-SCREW SET-SCREW 2B5 030060FWNS SCR-030-060 SCR-030-060 8B6 030060FWSA SCR-030-060WSA SCR-030-060WSA 2B7 030060FWTP SCR-030-060WTP SCR-030-060WTP 40B8 030060FWWS SCR03M060-WS-W SCR03M060-WS-W 44B9 NS-SCR00016BSCR03T060SR-W SCR03T060SR-W 2
B10 030080FNBI SCR-030-080NBI SCR-030-080NBI 1B11 030080FWNS SCR-030-080 SCR-030-080 1B12 030080FWWS SCR030080FWWS SCR030080FWWS 7B13 040060FWIT SCR-040-060WIT SCR-040-060WIT 2B14 NS-SCR00045BSCR04T070SR-W SCR04T070SR-W 4B15 040080FNBI SCR-040-080NBI SCR-040-080NBI 8B16 040080FWBI SCR-040-080 SCR-040-080 1B17 040080FWWS SCR040080FWWS SCR040080FWWS 8B18 NS-SCR00221BSCR04T060-D050050-W SCR04T060-D050050-W 2B19 040100FWSW SCR-040-100 SCR-040-100 2B20 NS-SCR00201BSCR03M025-D040014 SCR03M025-D040014 3B21 NS-SCR00206CSCR03M030-D040022 SCR03M030-D040022 6B22 030060FWIT SCR-030-060WIT SCR-030-060WIT 1
C1 CL030016FW CL-030 CL-030 1C2 CL030045FW CL-030 CL-030 4C3 CL060150FW CL-060 CL-060 1
E1 ER020SKP ER-020 ER-020 1E2 ER030SKP ER-030 ER-030 2E3 ER040SKP ER-040 ER-040 6E4 ER050SKP ER-050 ER-050 29E5 ER070SKP ER-070 ER-070 4E6 NS-CLP00003B CLIP040100G CLIP040100G 14E7 NS-CLP00008C CLIP050140W CLIP050140W 22
P1 HP02010SCH HP-020 HP-020 5P2 SP02008S-B SP-020 SP-020 3P3 SP02010S-B SFT-020-100SP-B SFT-020-100SP-B 8P4 SP02012FPA SP-020 SP-020 2P5 SP03012S-B SP-030 SP-030 1P6 SP02010FPA SP-020 SP-020 2
1 NS-BSH00004 BUSH080070MYU BUSH080070MYU 12 NS-BSH00002 BUSH060060MYU BUSH060060MYU 63 PR5500K047 ASM-RIBBON-PT ASM-RIBBON-PT 14 PF2144P013 センサー ホルダー Sensor holder 15 PF2147P021 PLY-18-RK PLY-18-RK 26 PF2147P032 FLNG-17-RK FLNG-17-RK 57 NS-MTL00009 METAL060060FC METAL060060FC 158 PF2185P009 GER-080-24 GER-080-24 29 PF2205P008 GER-080-22-OW GER-080-22-OW 3
10 PF2205P019 PLY-S2M-64-G26 PLY-S2M-64-G26 111 PF2205P026 DFスペーサー L 212 PF2210P054 PULLEY-G-IDOL-40-0.8 PULLEY-G-IDOL-40-0.8 213 PF2210P080 PULLEY-G-18-0.8 PULLEY-G-18-0.8 114 PF2210P092 PULLEY(G-18-0.8-5) PULLEY(G-18-0.8-5) 615 PF2210P375 PULLEY-MOT-S2M18 PULLEY-MOT-S2M18 117 PF2254P141 MSWレバーN 318 PF4048P114 GER.1.0-23 GER.1.0-23 219 PF4051P009 GER-1.0-24 GER-1.0-24 120 PF4051P033 GER-0.8-50-20 GER-0.8-50-20 1
6-1
Ref. No. Part No. 部品名 Part Name Qty21 PF4051P034 GER-0.8-20 GER-0.8-20 222 NS-MTL00017 METAL080070FC METAL080070FC 223 PR5002P225 テマワシローラー 124 PR5002P248 クロックディスク CLOCK DISK 125 PR5002P565 ASM-AC CODE SET-E ASM-AC CODE SET-E 126 PR5005P201 ハンテンプレート FT-PLATE 127 PR5100K038 ASM-LD RELAY 2 ASM-LD RELAY 2 128 PR5100P202 GER-0.8-50 GER-0.8-50 229 PR5100P218 PLY.S2M-22-60 PLY.S2M-22-60 130 PR5100P220 PLY.S2M-16-70 PLY.S2M-16-70 131 PR5100P247 PLY.S2M-43-18 PLY.S2M-43-18 132 PR5300P490 CL-BRUSH-3T CL-BRUSH-3T 133 PR5100P545 ASM-AC CORD 3M ASM-AC CORD 3M 134 PR5101K081 HR-HLGN-UNIT HR-HLGN-UNIT 135 PR5101P030 HR-CABLE-BKT HR-CABLE-BKT 136 PR5101P209 HR-SPOOL HR-SPOOL 137 PR5101P211 HR-CAM-ROLLER HR-CAM-ROLLER 238 PR5101P411 HR-CAUTION-LABEL HR-CAUTION-LABEL 139 PR5101P501 MOT-TP42FP8-505 MOT-TP42FP8-505 140 PR5200P034 START-SEN-BKT START-SEN-BKT 141 PR5200P410 PINCH-SPRING PINCH-SPRING 842 PR5200P441 SAFTY-STD-LABEL SAFTY-STD-LABEL 143 PR5200P524 MOT-KH56JM2B025 MOT-KH56JM2B025 144 PR5500K045 PBA-RIBBON-LD PBA-RIBBON-LD 145 PR5500K046 PBA-RIBBON-PT PBA-RIBBON-PT 146 PR5300K030 MOT-KH42JM2-UNIT MOT-KH42JM2-UNIT 147 PR5300K031 ASM-SENSOR RELAY ASM-SENSOR RELAY 148 PR5300K113 FT-PLT-R-ASSY FT-PLT-R-ASSY 149 PR5302K176 HR-FT-PLT-UNIT HR-FT-PLT-UNIT 150 PR5300K147 FT-WEIGHT-SHAFT-UNITFT-WEIGHT-SHAFT-UNIT 251 PR5300K151 FT-P0S-SEN-UNIT FT-P0S-SEN-UNIT 152 PR5300K181 RIBBON-COVER-UNIT RIBBON-COVER-UNIT 153 PR5300K198 MOVE-GUIDE-PLT-UNIT MOVE-GUIDE-PLT-UNIT 154 PR5300P109 FT-PLT-STAY FT-PLT-STAY 155 PR5300P120 FT-P0S-SEN-BKT FT-P0S-SEN-BKT 156 PR5300P121 FT-WEIGHT-PLT FT-WEIGHT-PLT 157 PR5300P156 MOVE-GUIDE-PLATE MOVE-GUIDE-PLATE 158 PR5300P205 RIBBON-COVER RIBBON-COVER 159 PR5300P225 PINCH-GAP PINCH-GAP 1060 PR5300P226 MOVE-GUIDE MOVE-GUIDE 161 PR5300P243 GEAR-1.0-14-0.8-56 GEAR-1.0-14-0.8-56 162 PR5300P272 RBN-COVER-SWITCH RBN-COVER-SWITCH 163 PR5300P283 FT-PLT-F FT-PLT-F 164 PR5300P285 FT-PINCH-ROLLER FT-PINCH-ROLLER 465 PR5300P286 FT-PST-PLY FT-PST-PLY 166 PR5302P217 GER-0.8-50-20-W GER-0.8-50-20-W 167 PR5300P341 FT-WEIGHT-SHAFT FT-WEIGHT-SHAFT 168 PR5300P400 TM166-8 TM166-8 569 PR5300P417 MOVE-GUIDE-SPRING MOVE-GUIDE-SPRING 170 PR5300P431 FT-ROLLER FT-ROLLER 271 PR5300P457 RBN-COV-SPRING RBN-COV-SPRING 172 PR5300P458 LINE-SEAL LINE-SEAL 173 PR5300P459 C-96-2 C-96-2 174 PR5002P488 ニスカロゴ niscalogo 175 PR5002P458 リビジョンカンリヒョウ RIBIZYONMARK 176 NS-BRG00125 BEARINGBB200320F BEARINGBB200320F 277 PR5500K050 PBA-SENSOR PBA-SENSOR 178 PR5302K168 HR-FRAME-UNIT-D HR-FRAME-UNIT-D 179 PR5302K156 HR-MAIN-UNIT HR-MAIN-UNIT 1
6-2
Ref. No. Part No. 部品名 Part Name Qty80818283848586878889 PR5302K005 EPROMクミ EPROM-ASSY 190 PR5302K002 PBA-CONT PBA-CONT 191 PR5302K011 ASM-BK/NF ASM-BK/NF 192 PR5302K012 ASM-NF/RY ASM-NF/RY 193 PR5300K013 ASM-RY ASM-RY 194 PR5350K017 ASM-FGND ASM-FGND 195 PR5302K015 ASM-HEAT ASM-HEAT 196 PR5302K016 ASM-I/L-SW ASM-I/L-SW 197 PR5302K017 ASM-MOTOR1 ASM-MOTOR1 198 PR5302K018 ASM-SENSOR1 ASM-SENSOR1 199 PR5302K019 ASM-SENSOR2 ASM-SENSOR2 1
100 PR5302K020 ASM-INTERFACE ASM-INTERFACE 1101 PR5302K021 ASM-TLP1241-RL ASM-TLP1241-RL 1102 PR5302K022 ASM-FUSE ASM-FUSE 1103 PR5302K031 HR-FUSE-UNIT HR-FUSE-UNIT 1104 PR5302P001 HR-FT-BKT HR-FT-BKT 1105 PR5302P003 HR-FT-FRAME-F HR-FT-FRAME-F 1106 PR5302P004 HR-CF-BKT HR-CF-BKT 1107 PR5302P007 HR-MAIN-MOT-BKT HR-MAIN-MOT-BKT 1108 PR5302P013 HR-BRAKE-BKT HR-BRAKE-BKT 1109 PR5302P071 HR-ROLL-BKT HR-ROLL-BKT 1110 PR5302P017 HR-PUSH-BKT HR-PUSH-BKT 1111 PR5302P018 HR-RBN-GID-BKT HR-RBN-GID-BKT 1112 PR5302P019 HR-SEPARATION-BKT HR-SEPARATION-BKT 1113 PR5302P020 HR-LOCK-HOOK HR-LOCK-HOOK 1114 PR5302P021 HR-LOCK-LEVER HR-LOCK-LEVER 1115 PR5302P022 HR-RBN-SEN-BKT-U HR-RBN-SEN-BKT-U 1116 PR5302P070 HR-LUMP-HOLDER-RL HR-LUMP-HOLDER-RL 2117 PR5302P029 HR-BOARD-BKT HR-BOARD-BKT 1118 PR5302P030 HR-BOARD-PLT HR-BOARD-PLT 1119 PR5302P031 HR-NF-PLT HR-NF-PLT 1120 PR5302P032 HR-FT-SEN-BKT HR-FT-SEN-BKT 1121 PR5302P035 HR-TRN-BKT HR-TRN-BKT 1122 PR5302P037 HR-RIGHT-COVER HR-RIGHT-COVER 1123 PR5302P038 HR-LEFT-COVER HR-LEFT-COVER 1124 PR5302P039 HR-BASE-GUIDE-U HR-BASE-GUIDE-U 1125 PR5302P040 HR-BASE-GUIDE-M HR-BASE-GUIDE-M 1126 PR5302P041 HR-MOVE-GUIDE-BKT HR-MOVE-GUIDE-BKT 1127 PR5302P042 HR-F-FRAME HR-F-FRAME 1128 PR5302P044 HR-BASE-FRAME HR-BASE-FRAME 1129130 PR5302P048 HR-FRM-STOPPER HR-FRM-STOPPER 1131 PR5302P049 HR-CARD-GID-BKT HR-CARD-GID-BKT 1132 PR5302P050 HR-SP-PLT HR-SP-PLT 1133 PR5302P052 HR-FUSE-BKT HR-FUSE-BKT 1134 PR5302P053 HR-FRM-STAY HR-FRM-STAY 1135 PR5302P062 HR-FT-SEN-BKT-2 HR-FT-SEN-BKT-2 1136 PR5302P064 HR-R-COVER HR-R-COVER 1137 PR5302P065 HR-JOINT-BKT HR-JOINT-BKT 1138 PR5302P066 HR-FT-POS-SEN-BKT HR-FT-POS-SEN-BKT 1139 PR5302P202 GER-0.8-32 GER-0.8-32 4
6-3
Ref. No. Part No. 部品名 Part Name Qty140 PR5302P203 GER-0.8-50-CHACK GER-0.8-50-CHACK 2141 PR5302P204 HR-RBN-JOINT HR-RBN-JOINT 1142 PR5302P206 HR-CAM HR-CAM 2143 PR5302P207 HR-CAM-POS-PLT HR-CAM-POS-PLT 1144 PR5302P134 HR-HOLDER-SLIDE HR-HOLDER-SLIDE 2145 PR5302P209 HR-PUSH-GUIDE HR-PUSH-GUIDE 4146 PR5302P210 GER-0.8-15 GER-0.8-15 1147 PR5302P212 HR-F-COVER HR-F-COVER 1148 PR5302P214 HR-TOP-COVER HR-TOP-COVER 1149 PR5302P215 HR-OPEN-COVER HR-OPEN-COVER 1150 PR5302P304 HR-CF-SFT HR-CF-SFT 1151 PR5302P308 HR-MOT-SFT HR-MOT-SFT 1152 PR5302P311 HR-WIND-OW-SFT HR-WIND-OW-SFT 1153 PR5302P312 HR-RBN-STUD HR-RBN-STUD 1154 PR5302P314 HR-CLOCK-SFT HR-CLOCK-SFT 1155 PR5302P316 HR-LOCK-SFT HR-LOCK-SFT 3156 PR5302P318 HR-CAM-SFT HR-CAM-SFT 1157 PR5302P320 HR-FRAME-SFT HR-FRAME-SFT 1158 PR5302P321 HR-WEIGHT-SFT HR-WEIGHT-SFT 1159 PR5302P324 HR-TOP-PUSH-SFT HR-TOP-PUSH-SFT 1160 PR5302P328 HR-RBN-GID-SFT HR-RBN-GID-SFT 1161 PR5302P401 HR-PUSH-SPR HR-PUSH-SPR 2162 PR5302P403 HR-RB-CHA-SPR HR-RB-CHA-SPR 2163 PR5302P404 HR-LOCK-HOOK-SPR HR-LOCK-HOOK-SPR 2164 PR5302P458 HR-PLATEN-ROLLER HR-PLATEN-ROLLER 1165 PR5302P406 HR-CAPSTAN-ROLLER HR-CAPSTAN-ROLLER 1166 PR5302P407 HR-CAPSTAN-ROLLER-1 HR-CAPSTAN-ROLLER-1 2167 PR5302P408 HR-PINCH-ROLLER HR-PINCH-ROLLER 3168 PR5302P409 HR-EJECT-ROLLER HR-EJECT-ROLLER 1169 PR5302P411 OTLC6-1700C OTLC6-1700C 1170 PR5302P413 OTLC6-100A OTLC6-100A 1171 PR5302P415 OTLC-400B OTLC-400B 1172 PR5302P418 HR-PULL-SPR HR-PULL-SPR 2173 PR5302P437 BM0504FN BM0504FN 6174 PR5302P423 HR-OPEN-SPR HR-OPEN-SPR 1175176 PR5302P459 HR-ROLL-HEAT HR-ROLL-HEAT 1177 PR5302P427 HR-TNS-SPR HR-TNS-SPR 2178 PR5302P428 AP-197-2-1 AP-197-2-1 1179 PR5302P510 1PT5S-312-N10 1PT5S-312-N10 1180 PR5101P513 TRN-デンゲントランス TRN 1181 PR5302P429 HR-MARKING-LABEL-10 HR-MARKING-LABEL-10 1182 PR5302P430 HR-MARKING-LABEL-20 HR-MARKING-LABEL-20 1183 PR5302K206 HR-FRAME-ASSY HR-FRAME-ASSY 1184 PR5302K208 HR-R-FRAME-ASSY HR-R-FRAME-ASSY 1185 PR5302P434 DMP-8 DMP-8 1186 PR5302K207 HR-MAIN-TNS-SPR HR-MAIN-TNS-SPR 1187 PR5302K201 HR-MAIN-TEN-ASSY HR-MAIN-TEN-ASSY 1188 PR5302K205 HR-RBN-MOT-UNIT HR-RBN-MOT-UNIT 1189 PR5302P055 HR-CARD-STOPPER HR-CARD-STOPPER 1190191192193194195196197198199
6-4
Ref. No. Part No. 部品名 Part Name Qty200 D022700000 DAT-104-619 DAT-104-619 2201 E120001199 W28XQ1A6 W28XQ1A6 1202 E120001551 DE2L-FAAA DE2L-FAAA 3203 E240000321 SUP-B3G-ER SUP-B3G-ER 1204205 E314000729 TLP1241(C5,F) TLP1241(C5,F) 4206 E314000780 KI1220-NA02LF KI1220-NA02LF 2207 E314000732 TLN119(B,F) TLN119(B,F) 1208 E314000731 TPS616(C,F) TPS616(C,F) 1209 E450000005 SKB-1M SKB-1M 3210 E450000204 SRー7Pー2 SRー7Pー2 1211 E450000566 EDSー1717U EDSー1717U 2212 E450000696 EDSー1208U EDSー1208U 4213 E450000734 LEDー0300 LEDー0300 1214 E450000850 FGC-8 FGC-8 1215 E450001134 RLWS-2T V0 RLWS-2T V0 5216 E450001139 RLWS-1T V0 RLWS-1T V0 5217 E450001140 RLWS-3T V0 RLWS-3T V0 7218 E450001146 RLMC-01T V0 RLMC-01T V0 4219 E450001148 RLMC-05T V0 RLMC-05T V0 8220221 E74585WE02SN53254-0270 53254-0270 1222 E314000781 GP1A57HRJ00F GP1A57HRJ00F 1223 E70009J511 CFS1/4C511J CFS1/4C511J 1224 E73110Z1041H RPEF11H104Z2K1A01 RPEF11H104Z2K1A01 1225 E74594WE03SN53253-0370 53253-0370 1226 PF2144K130 PCBーセンサー キバン PCBーセンサー キバン 1227 PR5500K044 PCB-SENSOR PCB-SENSOR 1228 PR5101P503 CBP-PR5101 I/F CBP-PR5101 I/F 1229 PR5101P515 HR-HALOGEN-LAMP HR-HALOGEN-LAMP 1230 PR5101P516 LMP-ハーネス LMP-ハーネス 1231 PR5101P517 LMP-コネクタ LMP-コネクタ 1232 NS-BLT00047 BELTS2M050040 BELTS2M050040 1233 NS-BLT00064 BELTS2M071040 BELTS2M071040 1234 NS-BLT00071 BELTS2M080040 BELTS2M080040 2235 NS-BLT00083 BELTS2M093040 BELTS2M093040 1236 NS-BLT00104 BELTS2M150060 BELTS2M150060 1237 NS-BRG00118 BEARINGRBB060130F BEARINGRBB060130F 2238 T0559BK009 チューブ TUBE 1239 E450001163 RLWS-1015T RLWS-1015T 1240241242243244245246247248249250
6-5
7-1
7-2
77
B8
B8
7-3
7-4
7-5
7-6