hawke catalogue.pdf

Over the past 45 years, Hawke has built a world-wide reputation in the Hazardous Area and Hostile Environment markets, with an innovative range of cable connection, termination and barrier products.

The underlying philosophy behind our Corporate Strategy has been a recognition of the fundamental principle that our products are concerned with safety, in an environment where failure can have catastrophic consequences to human life, the environment, expensive plant and valuable production - and in situations where the replacement of faulty components is often difficult.

This philosophy requires an enthusiastic participation in the development of new Safety Standards and Codes of Practice, and a product development programme which embraces these, together with advances in cable construction and materials. It requires that our products should be easy to select and install, because these activities are not only expensive but also affect the safety of the assembly. It requires that we provide informed technical advice, that our staff and customers are thoroughly trained, and that we have quality systems and a manufacturing plant which ensure Zero Defects. It means that we must transcend the mere requirements of having the "appropriate certification" and that we exceed the undemanding requirement that products be "fit for purpose" - whose purpose?

All the products we make (from Fire Barrier Transit systems to Fieldbus Power Supply systems) have a common underlying theme, which forms the basis of our Product Development Strategy :-

Product Development is an ongoing process, in which Hawke continues to invest heavily, and the cable glands described within are the culmination of a particularly concentrated effort over recent years.

The new rear sealing system not only meets the new ATEX Directive, but also uses a unique clamping system, giving higher retention forces than any other similar product on the market. It uses a new thermoset elastomer compound which provides superb resistance to high and low temperatures, to the ageing effects of Oxygen and Ozone, and Compression Set. It has the added benefit of being halogen-free, with low smoke and fume emission . . . . but, above all, it is safe. The system has the versatility to seal the entire range of cable sizes that can be accommodated by a particular entry size, without the need for special outer seals. This makes the cable gland easier and quicker to use, with less likelihood of an installer using the wrong seal. It also means easier product selection, and fewer items for our distributors to keep in stock, which should in turn mean improved stock availability. The cable acceptance range is marked on the rear nut, affording easier inspectability.

An example from our new range of cable glands illustrate these principles :-

As a company, we have all the obvious targets in terms of On-Time Delivery and Customer Service, Zero Defects, Investment in Manufacturing Facilities, and in the Training and Development of our People - and we perform to World-Class Standards,but . . . .

if there is one message we want to get across, it is our overriding concern for SAFETY.

Safety, Integrity and InspectabilityVersatility and ease of product selection

Ease and speed of useLowest lifetime cost solutions

Quality and Reliability

Introduction

1

Smarter productswww.ehawke.com

Cable Gland Selection Chart 4 - 6

ATEX Hazardous Area Cable Glands, (CENELEC, IEC) 7 - 20

Industrial General Purpose Cable Glands 21 - 27

North American Explosionproof and General Purpose Cable Glands 28 - 32

Cable Gland Accessories 33 - 37

Cable Gland Variations and Options 38

Hazardous Area Guidelines 39 - 66

Page No.

1.0 Potentially Explosive Atmospheres 39

2.0 Area Classification (Classification of Locations) 39

3.0 CENELEC and IEC Hazardous (Classified) Locations 39 - 43 3.1 Areas Classification 39 3.2 Classification Society 40 3.3 Design and Installation of Electrical Systems for Hazardous (Classified) Areas 40 3.4 Apparatus Selection According to Zones 41 3.5 Apparatus Selection According to the Ignition Temperature of the Gas or Vapour 41 3.6 Apparatus Selection According to Apparatus Grouping 42 3.7 Apparatus Construction Standards 42 3.8 Installation Standards and Codes 42 3.9 Inspection Standards and Codes 43

4.0 ATEX 94/9/EC Directive 43 - 444.1 ATEX 137 Directive 99/92/EC 44

5.0 Wiring Systems 45 - 48

5.1 CENELEC and IEC Wiring Methods 455.2 Wiring Methods for Type of Protection 'd' - Flameproof Enclosure 46 5.3 Wiring Methods for Type of Protection 'e' - Increased Safety 48

Contents

International2


13.0 Abbreviations, Accronyms and Definitions 62 - 65

Page No.

7.0 CE Marking 49 7.1 EMC, Electromagnetic Compatibility Directive 49 7.2 Low Voltage Directive 49

8.0 Certification/Listing/Approvals 49

9.0 CENELEC and IEC Degree of Protection, IP Code 50 - 56 9.1 Deluge Ingress Protection 51

10.0 IECEx Scheme 51

11.0 North American Hazardous (Classified) Locations 51 11.1 Area Classification 51 11.2 Apparatus Selection According to Class 1 53 11.3 Apparatus Selection According to the Ignition Temperature of the Gas or Vapors 54 11.4 Apparatus Selection According to the Ignition Temperature of the Dust 54 11.5 Apparatus Selection According to Apparatus Grouping 54 11.6 Apparatus Construction Standards 55 11.7 Installation Standards and Codes 56

12.0 Wiring Systems 56 - 61 12.1 National Electrical Code (NEC) Wiring Methods 56 12.2 Cable Seals, Class 1, Division 1 57 12.3 Cable Seals, Class 1, Division 2 57 12.4 United States Coast Guard - Wiring Methods 57 12.5 American Petroleum Institute - Wiring Methods 58 12.6 National Electrical Code (NEC) Zone Equipment Marking 60 12.7 National Electrical Code (NEC) Division Equipment Marking 60 12.8 North American Ingress Protection 61

6.1 Additional ATEX Marking 486.2 Additional CE Marking 49

6.0 Apparatus Marking - CENELEC and IEC (Group II) 48 - 49

Contents

International3


Cable Gland Selection Chart

International

ColourCoded

Catalogue Page No.

Cable GlandType

Pictorial View

Certification

CertificationOptions

IngressProtection

Sealing

Application/Cable Type

PSG 553/RAC

501/453/UNIV

501/453/RAC/L

501/453/RAC

IP66/67/68Deluge

IP66/67/68(Deluge option)



IP66/67/68Deluge

IP66/67/68Deluge

IP66/67/68Deluge

IP66/67/68Deluge

IP66/67/68Deluge

Indoor/outdoorArmoured/braided cable with

inner (optional) and outer sheath


inner lead sheath and outer sheath



Indoor/outdoorNon-armoured cable

Outer cable sheath seal

Two outer cable sheath seals

Inner and outer cable sheath seals

Inner lead sheath seal/electrical bond

and outer cable sheath seal

Inner (diaphragm) and outer

cable sheath seals

Inner (compound) and outer

cable sheath seals

Individual conductor seal


Inner (compound) and outer

cable sheath seals

Inner (compound) seal, lead sheathelectrical bond





inner and outer sheath





501/423

501/4217

8

9

10

11

12

13

14

15

16

ICG 653/UNIV

ICG 653/UNIV/L

ATEXEExd IIC/EExe II

Zone 1, 2, 21 & 22

ICG 623

II 2 GD

IEC

IEC

IEC

IEC

IEC

IEC

IEC

IEC

IEC

IEC

IP66/67/68Deluge

Indoor/outdoorNon-armoured cable,

conduit system


501/414


Zone 1, 2, 21 & 22II 2 GD


Zone 1, 2, 21 & 22II 2 GD


Zone 1, 2, 21 & 22II 2 GD


Zone 1, 2, 21 & 22II 2 GD


Zone 1, 2, 21 & 22II 2 GD


Zone 1, 2, 21 & 22II 2 GD


Zone 1, 2, 21 & 22II 2 GD


Zone 1, 2, 21 & 22II 2 GD


Zone 1, 2, 21 & 22II 2 GD

4

To the best of our knowledge the information contained in this brochure, is accurate at the time of going to print and the company reserves the right to improve or modify any product illustrated without notification. The company is unable to accept liability for any inaccuracies, errors or omissions that may exist. It is the customer's responsibility to ensure that the product is suitable for their application.

All copyright reserved-Hawke Cable Glands Ltd 2001.This document and all copyright therein is the property of: Hawke International a trading name of Hawke Cable GlandsLtd (A member of the McKechnie Group of Companies).Copyright Condition: This document shall be used only for the purpose for which it is provided and no reproduction or publication of the document may be made and no article may be manufactured or assembled in accordance with information contained in the document without prior written consent of the owner.



ColourCoded

Catalogue Page No.

Pictorial View

International5




Cable GlandType

Certification


IngressProtection

Sealing


121

351/RAC

501/453ICG 653

153Sizes G, H & J

CSB 656 IP66/67/68Deluge

IP66/67/68(Delugeoption)

IP66(Delugeoption)

IP66(Delugeoption)

IP66/67/68Deluge

IP66/67/68Deluge

IP66/67/68Deluge

Dry Indoor/outdoorArmoured/braided cable with






Individualconductor

seal

Individualconductor

(compound) seal


Inner and outer cable sheath seals


Indoor/outdoorIndividual conductors,

conduit system

Indoor/outdoorIndividual conductors,

conduit system



SB 47417

18

19

20

21

22

23

24

25

26

27

150/RAC

151/RAC

123


Zone 1, 2, 21 & 22II 2 GD

ATEXEExe II

Zone 1, 2, 21 & 22II 2 GD

EN 50262

EN 50262

BS 6121

EN 50262

EN 50262

EN 50262

EN 50262

IEC

IEC

IEC

IEC

IEC

IEC

IEC

IEC

IEC

IEC



IP66/67/68Deluge

IP66/67(Delugeoption)

IP66/67(Delugeoption)

Indoor/outdoorArmoured/braided cable

with inner and outer cable sheath

Inner (diaphragm) and outer

cable sheath seal


Indoor/outdoorNon-armoured cable,

conduit system 114

153/RAC

153/RAC/L


Two outer cable sheath seals



Inner seal/lead sheath electrical bond and outer

cable sheath seal

IEC


Zone 1, 2, 21 & 22II 2 GD


Zone 1, 2, 21 & 22II 2 GD



Zone 1, 2, 21 & 22II 2 GD

IEC



International

Cable GlandType

Certification

IngressProtection

Sealing


755

753

711

710

70128

29

30

31

32

33 - 36

33 - 36

33 - 36

37

38

IP66/67/68Deluge

IP66/67/68Deluge

IP66/67/68Deluge




Indoor/outdoor

Inner (compound) and outer cable

jacket seals


jacket seals


jacket seals


jacket seals

Outer cablejacket seal

Indoor/outdoorType MC and Teck cables

Indoor/outdoorNon-armored cable

Indoor/outdoorType MC and Teck cables

Indoor/outdoorArmored/braided cable with

inner (option) and outer jacket

Indoor/outdoorArmored MarineShipboard cable

Adaptors/Reducers

Cable GlandVariations& Options

Accessories

Accessories

Accessories

UL/cULUL 514B

UL/cULClass 1 Division 1

Groups A, B, C & D


Groups A, B, C & D


Groups A, B, C & D


Groups A, B, C & D

Colour Coded

CataloguePage No.

Pictorial View


C

C

C

C

C

6


Application

Function

'G' Approx15.0mm

MetricEntry

'B

'

Entr

y Thr

ead

Outdoor or Indoor use. For use with non-armoured elastomer and plastic insulated cables. See technical section of catalogue for installation rules and regulations.

Provides a high pullout resistant seal onto the cables outer sheath. When used in increased safety applications, this cable gland may be used with braided cable where the braid and the cables outer sheath pass into the enclosure. The braid must be suitably terminated into the enclosure.

ATEX Cable Gland Ordering ExamplesCable Gland Type/Size/Thread e.g. 501/421/C/M32 501/421/C/1" NPT

Flameproof and Increased Safety

501/421 Cable Gland Type

ATEX

International7


Materials & FinishesHawke cable glands are manufactured as standard in brass.Alternative materials and plating are available.

Technical Data Flameproof EExd and Increased Safety EExe. II 2 GD BASEEFA Certificate No. BAS 01 ATEX 2070X. For sizes Os - F. BASEEFA Certificate No. BAS 01 ATEX 2294X. For sizes G - J. Suitable for use in Zone 1, Zone 2, Zone 21 and Zone 22. Suitable for use in Gas Groups IIA, IIB and IIC.

IP66, IP67 and IP68 ingress protection to IEC 60529, EN 60529 and NEMA 4X. DTS01 deluge protection certified by ITS. Operating temperature range -60C to +80C as standard. Option available, Exd IIC, Exe II.

Construction and test standards EN 50014, EN 50018, EN 50019 and EN 50281-1-1.IEC 60079-0, IEC 60079-1 and IEC 60079-7.

Option available, BR-Exd IIC/Exe II.certificate No. Ex-017/2001X.

Alternative thread sizes available. See page 38 Accessories including locknuts, sealing washers, shakeproof washers, shrouds, adaptors and reducers available. See pages 33 - 37

All Metric entry threads are 1.5mm pitch medium fit.All dimensions in millimetres (except*). Sizes Os and O are available with an M16 thread size. For O size with M16 thread, the maximum cable outer sheath diameter is 10.9mm.Assembly instruction data sheet No. A.I. 307. For sizes Os to F.Assembly instruction data sheet No. A.I. 326. For sizes G to J.

Cable Gland with Alternative Seal (S)

e.g. 501/421/C/M32/S 501/421/C/1" NPT/S

CABLE GLAND SELECTION TABLE

Entry ThreadSize

Metric

SizeRef.

NPT*

'G'

AcrossFlats

AcrossCorners

HexagonDimensions

OsOABCC2DE

F

HJ

M20M20

M20M25M32M40

M50M63M75M80

M90M100

""

2"

2"3"-

3"4"

3.07.5

11.013.019.025.0

31.542.554.5

8.011.914.320.226.532.5

44.456.368.2

8.59.515.522.027.539.048.5

13.415.421.228.034.846.558.3

24.0383938414342585356565656

24.030.036.046.055.0

65.080.095.0

27.727.734.641.653.163.575.192.4109.6

Min. Max.

Outer Sheath 'B'

Min. Max.

G

Cable Acceptance Details

- -- -

1"1"

""

StandardSeal

AlternativeSeal (S)

- -- -- -

67.067.075.0

73.077.691.6

106.4

115.0127.0

123.0

132.8146.7



Technical Data Flameproof EExd and Increased Safety EExe. II 2 GD BASEEFA Certificate No. BAS 01 ATEX 2071X. For sizes Os - F. BASEEFA Certificate No. BAS 01 ATEX 2295X. For sizes G - J. Suitable for use in Zone 1, Zone 2, Zone 21 and Zone 22. Suitable for use in Gas Groups IIA, IIB and IIC.

IP66, IP67 and IP68 ingress protection to IEC 60529, EN 60529 and NEMA 4X. DTS01 deluge protection certified by ITS. Additional deluge protection seal also available. Operating temperature range -60C to +80C as standard. Option available, Exd IIC, Exe II.


8



International



ATEX Cable Gland Ordering ExamplesCable Gland Type/Size/Thread e.g. 501/423/C/M32 501/423/C/1" NPT


e.g. 501/423/C/M32/S 501/423/C/1" NPT/S


Entry ThreadSize

Metric

SizeRef.

NPT*

'G'

AcrossFlats

AcrossCorners

HexagonDimensions

OsOA

BCC2DEF

HJ

M20M20

M20

M25M32M40M50M63

M75M80M90M100

""

2"2"3"-

3"

4"

3.07.5

11.0

13.019.025.031.542.554.567.067.0

75.0

73.077.691.6

8.011.914.320.226.532.544.456.368.2

8.59.5

15.522.027.539.048.5

13.415.421.228.0

34.846.558.3

24.067686469727310098100

100100100

24.030.0

36.046.0

55.065.080.095.0

27.727.734.6

41.653.1

63.575.192.4109.6

106.4115.0127.0

123.0132.8146.7

Min. Max.

Outer Sheath 'B'

Min. Max.

G


- -- -

1"1"

""

StandardSeal

AlternativeSeal (S)

- -- -- -

'G' Approx15.0mm

'B

'

Entr

y Thr

ead

MetricEntry




ATEX

Application

Function


Outdoor or Indoor use. For use with non-armoured elastomer and plastic insulated cables. May be used on cables incorporating inner and outer cable sheaths. See technical section of catalogue for installation rules and regulations. Provides a high pullout resistant seal onto the cables outer sheath at two independent sealing points. When used in increased safety applications, this cable gland may be used with braided cable where the braid and the cables outer sheath pass into the enclosure. The braid must be suitably terminated inside the enclosure.

Armour/Braid'C'

Technical Data

Function

Application

Materials & Finishes

Outdoor or Indoor use. For use with single wire armoured 'W', wire braided 'X' and steel tape armoured 'Z' elastomer and plastic insulated cables.

Flameproof EExd and Increased Safety EExe. II 2 GD BASEEFA Certificate No. BAS 01 ATEX 2072X. For sizes Os - F. BASEEFA Certificate No. BAS 01 ATEX 2296X. For sizes G - J. Suitable for use in Zone 1, Zone 2, Zone 21 and Zone 22. Suitable for use in Gas Groups IIA, IIB and IIC.

IP66, IP67 and IP68 ingress protection to IEC 60529, EN 60529 and NEMA 4X. Operating temperature range -60C to +80C as standard. Option available, Exd IIC, Exe II.

Provides armour clamping using one clamping arrangement for all armour/braid types 'W', 'X' and 'Z'. Provides a seal on the cables inner sheath. Deluge protection option available.

Hawke cable glands are manufactured as standard in brass.Alternative materials and plating are available.


See technical section of catalogue for installation rules and regulations.

Provides a high pullout resistance and low smoke and fume, zero halogen seal onto the cables outer sheath.

Alternative thread sizes available. See page 38 Alternative non-standard armour clamping rings available. See page 38Accessories including locknuts, sealing washers, shakeproof washers, earth tags, shrouds, adaptors and reducers available. See pages 33 - 37

All Metric entry threads are 1.5mm pitch medium fit.All dimensions in millimetres (except*). Sizes Os and O are available with an M16 thread size. For O size with M16 thread, the maximum cable inner sheath diameter is 10.9mm.# Dedicated armour clamping rings are fitted. Please specify armour type and size.Assembly instruction data sheet No. A.I. 302. For sizes Os to F.Assembly instruction data sheet No. A.I. 329. For sizes G to J.

ATEX Cable Gland Ordering ExamplesCable Gland Type/Size/Thread e.g. 501/453/RAC/C/M32 501/453/RAC/C/1" NPT


e.g. 501/453/RAC/C/M32/S 501/453/RAC/C/1" NPT/S

International9





Entry ThreadSize Standard

SealAlternative

Seal (S)

Outer Sheath'B'

Inner Sheath 'A'

Metric

SizeRef.

NPT*

'G'AcrossFlats

AcrossCorners

HexagonDimensions

OsOABCC2DE

F

H J

M20M20

M20M25M32M40

M50M63M75

M80M90M100

""

2"2"3"

-

3"4"

3.07.5

11.013.019.025.0

31.542.554.5

11.914.320.226.532.5

44.456.368.2

8.59.515.522.027.539.048.5

13.415.421.228.034.846.558.3

24.024.030.036.046.055.065.080.095.0

27.727.734.641.653.163.575.192.4109.6

Min. Max. Min. Min.Max. Max.

G


8.0

12.516.922.028.036.046.057.0

20.526.033.041.052.665.378.0

5.5 12.09.5 16.0

0.9/1.250.9/1.250.9/1.251.25/1.61.6/2.01.6/2.01.8/2.51.8/2.51.8/2.5

0/0.70/0.70/0.70/0.70/0.70/0.70/1.00/1.00/1.0

Larger cable glands available in 501/453 design as shown below. See page 19

1"1"

""

8181

839598105133126

121121121

134

67.067.075.0

73.077.691.6

75.075.088.0

89.589.5

104.5

106.4

115.0127.0

123.0

132.8146.7

###

###

'C'Armour/Braid

Orientation2

Orientation1

- -- -- -

- -- -

'A

'

Entr

y Thr

ead

'G' Approx

MetricEntry

'B

'

15.0mm


501/453/RAC Cable Gland Type

ATEX

Armour/Braid'C'

'B

'

'A

'

Entr

y Thr

ead

MetricEntry

Lead Sheath Bond

15.0mm 'G' Approx

ATEX Cable Gland Ordering ExampleCable Gland Type/Size/Thread/Standard Inner Seal + Bond e.g. 501/453/RAC/C/M32/L 501/453/RAC/C/1" NPT/L

Application

Function

Technical Data

Outdoor or Indoor use. For use with single wire armoured 'W', wire braided 'X' and steel tape armoured 'Z' cables with a lead inner sheath. See technical section of catalogue for installation rules and regulations Provides armour clamping using one clamping arrangement for all armour/braid types 'W', 'X' and 'Z'. Provides a seal and an electrical bond on the cables lead inner sheath. Provides a high pullout resistance and low smoke and fume, zero halogen seal onto the cables outer sheath.

Deluge protection option available.


IP66, IP67 and IP68 ingress protection to IEC 60529, EN 60529 and NEMA 4X. Operating temperature range -60C to +80C as standard.

Zone 21 and Zone 22.Suitable for use in Gas GroupsIIA, IIB and IIC.Construction and test standards EN 50014, EN 50018, EN 50019 and EN 50281-1-1.IEC 60079-0, IEC 60079-1 and IEC 60079-7.

Flameproof EExd IIC and Increased Safety EExe II. II 2 GD BASEEFA Certificate No. BAS 01 ATEX 2072X. Fos sizes O - F. BASEEFA Certificate No. BAS 01 ATEX 2296X. For sizes G - J. Suitable for use in Zone 1, Zone 2


501/453/RAC/L Cable Gland Type

International10




ATEX


Entry ThreadSize

Metric

SizeRef.

NPT*

'G'

AcrossFlats

AcrossCorners

HexagonDimensions

OABCC2DE

F

M20

M20M25M32M40

M50M63M75

"

2"

2"3"

11.015.522.027.539.051.0

15.421.228.034.846.558.3

24.030.036.046.055.0

65.080.095.0

27.734.641.653.163.575.192.4109.6

Inner Lead Sheath 'A'Outer Sheath

'B'Alternative Seal + Bond

Max. Max.Min. Max.Min.Min.


Alternative thread sizes available. See page 38Alternative non-standard armour clamping rings available. See page 38Accessories including locknuts, sealing washers, shakeproof washers, earth tags, shrouds, adaptors and reducers available. See page 33 - 37

All Metric entry threads are 1.5mm pitch medium fit.All dimensions in millimetres (except*). Size O is available with an M16 thread size. For O size with M16 thread, the maximum cable inner sheath diameter is 10.9mm.# Dedicated armour clamping rings are fitted. Please specify armour type and size.Assembly instruction data sheet No. A.I. 302 + 336. For sizes O to F.Assembly instruction data sheet No. A.I. 329 + 336. For sizes G to J.

1"1"

""

H J

M80M90M100

- - -- -- -

3"4"

G

Larger cable glands available in 501/453/L design as shown below.

121

81839598

105133126134

121121

59.968.979.4

68.573.187.1

75.075.088.0

89.589.5104.5

106.4

115.0127.0

123.0

132.8146.7

Cable Gland with Alternative Inner Seal + Bond

e.g. 501/453/RAC/C/M32/K 501/453/RAC/C/1" NPT/K

###

###

'C'Armour/Braid

Orientation2

Orientation1

12.516.922.028.036.046.057.0

20.526.033.041.052.665.378.0

9.5 16.0 0.9/1.250.9/1.251.25/1.61.6/2.01.6/2.01.8/2.51.8/2.51.8/2.5

0/0.70/0.70/0.70/0.70/0.70/1.00/1.00/1.0

8.513.019.025.031.542.054.5

10.8

16.722.528.540.352.063.8

7.5 8.5 - -- -

Standard Seal + Bond

Technical Data

Function

Application


'A

'

Entr

y Thr

ead

'G' Approx15.0mm

MetricEntry

DelugeBoot

DiaphragmSeal

Armour/Braid'C'

'B

'

Outdoor or Indoor use. For use with single wire armoured 'W', wire braided 'X' and steel tape armoured 'Z' elastomer and plastic insulated cables. Suitable for use with cables that exhibit 'cold flow' characteristics.

ATEX Cable Gland Ordering ExamplesCable Gland Type/Size/Thread e.g. 501/453/UNIV/C/M32 501/453/UNIV/C/1" NPT



Provides armour clamping using one clamping arrangement for all armour/braid types 'W', 'X' and 'Z'. Provides a diaphragm seal on the cables inner sheath. A diaphragm seal will not damage cable that has 'cold flow' characteristics. Provides an outer deluge seal to prevent moisture ingress to the cable armour/braid.




Option available, BR-Exd IIC/Exe II.certificate No. Ex-017/2001X.

Provides a high pullout resistance and lowsmoke and fume, zero halogen seal onto thecables outer sheath.


501/453/UNIV Cable Gland Type

ATEX

International11





Entry ThreadSize

Metric

SizeRef.

NPT*

'G'

AcrossFlats

AcrossCorners

HexagonDimensions

OsOABCC2DE

F

H J

M20M20

M20M25M32M40

M50M63M75

M80M90M100

""

1"1"

2"2"3"

-

3"4"

3.07.59.412.117.623.1

28.939.950.5

8.111.914.320.226.532.5

44.456.368.2

12.516.922.028.036.046.057.0

20.526.033.041.052.665.378.0

24.024.030.036.046.055.0

65.080.095.0

27.727.734.641.653.163.575.192.4109.6

Inner Sheath'A'

Min. Max.

Outer Sheath'B'

Min. Max.

G


5.5 12.09.5 16.0

103

0.9/1.250.9/1.250.9/1.251.25/1.61.6/2.01.6/2.01.8/2.51.8/2.51.8/2.5

0/0.70/0.70/0.70/0.70/0.7

0/0.70/1.00/1.00/1.0

878789

100

110133134140

Alternative thread sizes available. See page 38 Alternative non-standard armour clamping rings available. See page 38Accessories including locknuts, sealing washers, shakeproof washers, earth tags, shrouds, adaptors and reducers available. See pages 33 - 37

All Metric entry threads are 1.5mm pitch medium fit.All dimensions in millimetres (except*). Sizes Os and O are available with an M16 thread size. For O size with M16 thread, the maximum cable inner sheath diameter is 10.9mm.# Dedicated armour clamping rings are fitted. Please specify armour type and size.Assembly instruction data sheet No. A.I. 300. For sizes Os to F.Assembly instruction data sheet No. A.I. 329. For sizes G to J.

Larger cable glands available in 501/453 design as shown below. See page 19

""

121121121

67.067.075.0

73.077.691.6

75.075.088.0

89.589.5104.5

106.4

115.0127.0

123.0

132.8146.7

#

##

#

##

'C'Armour/Braid

Orientation2

Orientation1


Technical Data

'G' Approx15.0mm

MetricEntry

Entr

y Thr

ead

'B

'

ATEX Cable Gland Ordering ExamplesCable Gland Type/Size/Thread e.g. PSG 553/RAC/C/M32 PSG 553/RAC/C/1" NPT

The required number of holes for the cores are punched in the seal by means of a special tool to suit the core size.


Flameproof EExd and Increased Safety EExe. II 2 GD BASEEFA Certificate No. BAS 01 ATEX 2074X. Suitable for use in Zone 1, Zone 2, Zone 21 and Zone 22. Suitable for use in Gas Groups IIA, IIB and IIC.

IP66, IP67 and IP68 ingress protection to IEC 60529 and EN 60529. Operating temperature range -60C to +80C as standard.


Armour/Braid'C'



ATEXPSG 553/RAC

Cable Gland Type

International12


Application

Function

Outdoor or Indoor use. For use with single wire armoured 'W', wire braided 'X' and steel tape armoured 'Z' elastomer and plastic insulated cables. For particular use with :- Cables that are not substantially compact and circular, have extruded bedding and the fillers, if any, are hygroscopic (eg. not effectively filled).b) Cables that exhibit "Cold Flow"characteristics. See technical section of catalogue for installation rules and regulations.

Provides armour clamping using one clamping arrangement for all armour/braid types 'W', 'X' and 'Z'.

a)

Provides a barrier seal between the individual insulated cores within the cable and prevententry of the products of an explosion intothe cable.

Deluge protection option available.

Alternative thread sizes available. See page 38Alternative non-standard armour clamping rings available. See page 38Accessories including locknuts, sealing washers, shakeproof washers, earth tags, shrouds, adaptors and reducers available. See pages 33 - 37

All Metric entry threads are 1.5mm pitch medium fit.All dimensions in millimetres (except*).Assembly instruction data sheet No. A.I. 312.

CABLE GLAND SIZE FOR CORE SIZE & NUMBER

Maximum No.of Cores

A & B743

1.5 2.5

Cores Cross Sectional Area mm

4.0 6.0 10.0

---

---

--

PUNCH TOOL SIZE DETAILSPunch Ref.

Core C.S.A. mmNo.1 No.1 No.2 No.2 No.31.5 2.5 4.0 6.0 10.0

A & B B & C C B

C

B


Entry ThreadSize

Metric

SizeRef.

NPT*

'G'

AcrossFlats

AcrossCorners

HexagonDimensions

ABC

M20M25M32

12.516.922.0

20.526.033.0

30.036.046.0

34.641.653.1

Outer Sheath'B'

Min. Max.


0.9/1.251.25/1.61.6/2.0

0/0.70/0.70/0.71"

""

8899101

Punch Tool Ordering Example e.g. Punch Tool Number 1.

'C'Armour/Braid

Orientation2

Orientation1



Application

Technical Data


Function

'G' Approx15.0mm

MetricEntry

'B

'

'D

'

Entr

y Thr

ead

'E

'

InspectableCompound

Outdoor or Indoor use. For use with non-armoured elastomer and plastic insulated cables.For particular use with :- Cables that are not substantially compact and circular, have extruded bedding and the fillers, if any, are hygroscopic (eg. not effectively filled).b) Enclosures containing an ignition source in gas group II C areas.c) Enclosures exceeding 2 litres in volume, containing an ignition source and installed in a Zone 1 area.d) Cables that exhibit "Cold Flow" characteristics. See technical section of catalogue for installation rules and regulations.

ATEX Cable Gland Ordering ExamplesCable Gland Type/Size/Thread e.g. ICG 623/C/M32 ICG 623/C/1" NPT

IP66, IP67 and IP68 ingress protection to IEC 60529, EN 60529 and NEMA 4X. DTS01 deluge tested by ITS. Operating temperature range -60C to +80C as standard. Option available, Exd IIC, Exe II.



Construction and design standards EN 50014, EN 50018, EN 50019 and EN 50281-1-1.IEC 60079-0, IEC 60079-1 and IEC 60079-7.


e.g. ICG 623/C/M32/S ICG 623/C/1" NPT/S

The compound chamber may be seperated from the compound to ensure that the chamber has been effectively filled.

Two part sealing compound and assembly instructions are supplied with the cable gland.


Provides a barrier seal between the individual insulated cores within the cable and prevent entry of the products of an explosion into the cable.Assembly of the cable gland compresses and distributes the compound evenly toeffect a barrier seal at the point of entryinto the enclosure.


ICG 623 Cable Gland Type

ATEX

International13


a)


Entry ThreadSize

Metric

SizeRef.

NPT*

'G'AcrossFlats

AcrossCorners

HexagonDimensions

OABCC2DE

F

M20M20M25M32M40

M50M63M75

"

1"1"2"

2"3"

11.016.221.926.337.1

47.859.0

12.518.424.729.741.7

53.566.2

24.06969

69717778959698

30.036.046.055.0

65.080.095.0

27.734.641.653.163.575.192.4109.6

Inner Sheath/Cores

Outer Sheath 'B'

Max.


'D' 'E'

8.9 10.0 61021426080

100120

Min. Max. Min.

StandardSeal

AlternativeSeal (S)

7.511.013.019.025.0

31.542.554.5

11.914.320.226.532.5

44.456.368.2

8.59.515.522.027.539.048.5

13.415.421.228.034.846.558.3

- -- -

Alternative thread sizes available. See page 38Accessories including locknuts, sealing washers, shakeproof washers, shrouds, adaptors and reducers available.See pages 33 - 37

All Metric entry threads are 1.5mm pitch medium fit.All dimensions in millimetres (except*).

Assembly instruction data sheet No. A.I. 305.

""

Max.OverCores

Max.Inner

Sheath

Max.No.Of

Cores

Os M20 " 8.0 8.0 8.03.0 24.0 27.76



Application

Function


Technical Data

Provides an outer deluge seal to prevent moisture ingress to the cable armour/braid.

Provides a high pullout resistance and lowsmoke and fume, zero halogen seal onto the cables outer sheath.

effect a barrier seal at the point of entryinto the enclosure. The compound chamber may be seperated from the compound to ensure that the chamber has been effectively filled.

Assembly of the cable gland compresses and distributes the compound evenly to

Two part sealing compound and assemblyinstructions are supplied with the cablegland.

Provides armour clamping, using one clamping arrangement for all armour/braid types ' W', 'X' and 'Z'.

'G' Approx15.0mm

MetricEntry

DelugeBoot

'B

'

Armour/Braid'C'

'D

'

Entr

y Thr

ead

'E

'

InspectableCompound

Outdoor or Indoor use. For use with single wire armoured 'W', wire braided 'X' and steel tape armoured 'Z' elastomer and plastic insulated cables.For particular use with :- Cables that are not substantially compact and circular, have extruded bedding and the fillers, if any, are hygroscopic (eg. not effectively filled).b) Enclosures containing an ignition source in gas group II C areas.c) Enclosures exceeding 2 litres in volume, containing an ignition source and installed in a Zone 1 area.d) Cables that exhibit "Cold Flow"characteristics. See technical section of catalogue for installation rules and regulations.

Provides a barrier seal between the individual insulated cores within the cable and prevent entry of the products of an explosion into the cable.

ATEX Cable Gland Ordering ExamplesCable Gland Type/Size/Thread

e.g. ICG 653/UNIV/C/M32 ICG 653/UNIV/C/1" NPT






ICG 653/UNIV Cable Gland Type

ATEX

International14


a)


Entry ThreadSize

Metric

SizeRef.

NPT*

'G'AcrossFlats

AcrossCorners

HexagonDimensions

OOs

ABCC2DE

F

H J

M20M20M25M32M40

M50M63M75

M80M90M100

"M20 "

2"

2"3"

-

3"4"

11.016.221.926.337.1

47.859.0

62.870.980.3

74.083.093.0

12.518.424.729.741.7

53.366.2

24.030.036.046.055.0

65.0

80.095.0

27.734.641.653.163.575.1

92.4109.6

106.4115.0127.0

123.0132.8146.7

Inner Sheath/Cores

Outer Sheath 'B'

G


8724.0 27.787

89100

110133

Alternative thread sizes available. See page 38 Accessories including locknuts, sealing washers, shakeproof washers, earth tags, shrouds, adaptors and reducers available. See pages 33 - 37

All Metric entry threads are 1.5mm pitch medium fit.All dimensions in millimetres (except*).# Dedicated armour clamping rings are fitted. Please specify armour type and size.

Assembly instruction data sheet No. A.I. 301. For sizes Os to F.Assembly instruction data sheetNo. A.I. 327. For sizes G to J.

Larger cable glands available in ICG 653 design as shown below. See page 19

'D' 'E'

8.9 10.0 68.9 10.0 6

1021426080

100120

140160180

Min. Max.

9.512.516.922.028.036.046.057.0

75.075.088.0

89.589.5104.5

16.05.5 12.0

20.526.033.041.052.6

65.378.0

0.9/1.250.9/1.251.25/1.61.6/2.01.6/2.01.8/2.51.8/2.51.8/2.5

0/0.70.9/1.25 0/0.7

0/0.7 0/0.70/0.70/0.70/1.00/1.00/1.0

103

133

133133132

140

""1"

1"

Max.No.Of

Cores

Max.OverCores

Max.Inner

Sheath

###

###

'C'Armour/Braid

Orientation2

Orientation1



'B

'

'G' Approx

InspectableCompound

'E

'

DelugeBoot

Lead Sheath Bond

Entr

y Thr

ead

15.0mm

MetricEntry

'D

'

ATEX Cable Gland Ordering ExampleCable Gland Type/Size/Thread/Bond

e.g. ICG 653/UNIV/C/M32/L ICG 653/UNIV/C/1" NPT/L

Application

Function

Technical Data


IP66, IP67 and IP68 ingress protection to IEC 60529, EN 60529 and NEMA 4X. DTS01 deluge protection certified by ITS. Operating temperature range -60C to +80C as standard.

Zone 21 and Zone 22.Suitable for use in Gas Groups IIA, IIB and IIC.Construction and test standards EN 50014, EN 50018, EN 50019 and EN 50281-1-1.IEC 60079-0, IEC 60079-1 and IEC 60079-7.

Flameproof EExd IIC and Increased Safety EExe II. II 2 GD BASEEFA Certificate No. BAS 01 ATEX 2080X. For sizes Os - F. BASEEFA Certificate No. BAS 01 ATEX 2297X. For sizes G - J. Suitable for use in Zone 1, Zone 2

Two part sealing compound and assemblyinstructions are supplied with the cablegland.

Alternative thread sizes available. See page 38 Accessories including locknuts, sealing washers, shakeproof washers, earth tags, shrouds, adaptors and reducers available. See pages 33 - 37

All Metric entry threads are 1.5mm pitch medium fit.All dimensions in millimetres (except*). Sizes Os and O are available with an M16 thread size. For O size with M16 thread,the maximum cable inner sheath diameteris 10.9mm.# Dedicated armour clamping rings are fitted. Please specify armour type and size.

Assembly instruction data sheet No. A.I. 301 + 336. For sizes Os to F.Assembly instruction data sheetNo. A.I. 327 + 336. For sizes G to J.


ICG 653/UNIV/L Cable Gland Type

effect a barrier seal at the point of entryinto the enclosure. The compound chamber may be seperated from the compound to ensure that the chamber has been effectively filled.

Assembly of the cable gland compresses and distributes the compound evenly to

Provides an outer deluge seal to prevent moisture ingress to the cable armour/braid.

Provides a high pullout resistance and lowsmoke and fume, zero halogen seal onto the cables outer sheath.

Provides armour clamping, using one clamping arrangement for all armour/braid types ' W', 'X' and 'Z'.Provides a seal and an electrical bond onthe cables lead inner sheath.

Outdoor or Indoor use. For use with single wire armoured 'W', wire braided 'X' and steel tape armoured 'Z' elastomer and plastic insulated cables with lead inner sheath.For particular use with :- Cables that are not substantially compact and circular, have extruded bedding and the fillers, if any, are hygroscopic (eg. not effectively filled).b) Enclosures containing an ignition source in gas group II C areas.c) Enclosures exceeding 2 litres in volume, containing an ignition source and installed in a Zone 1 area.d) Cables that exhibit "Cold Flow"characteristics. See technical section of catalogue for installation rules and regulations.

Provides a barrier seal between the individual insulated cores within the cable and prevent entry of the products of an explosion into the cable.

a)

International15


ATEX


Entry ThreadSize

Metric

SizeRef.

NPT*

OABCC2DE

F

M20M20M25M32M40

M50M63M75

"

2"

2"3"

10.816.221.926.3

37.147.859.0

10.816.722.528.5

40.052.063.8

Lead Inner Sheath/Cores

Outer Sheath 'B'


'D' 'E'

8.5 8.54.07.4

11.014.021.0

27.039.051.0

61021426080100120

Min. Max.

9.512.516.922.028.036.046.057.0

16.020.526.033.041.052.6

65.378.0

0.9/1.250.9/1.251.25/1.61.6/2.01.6/2.01.8/2.51.8/2.51.8/2.5

0/0.7Os M20 " 8.5 8.54.0 6 5.5 12.0 0.9/1.25 0/0.7

0/0.7 0/0.70/0.70/0.70/1.00/1.00/1.0

""1"

1"

Max.No.Of

Cores

Max.OverCores

Max.Inner

Sheath

Min.Inner

Sheath

H J

M80M90M100

-

3"4"

62.870.980.3

69.078.087.0

60.064.578.5

G

Larger cable glands available in ICG 653/L design as shown below.

140160180

75.075.088.0

89.589.5104.5

###

###

'G'AcrossFlats

AcrossCorners

HexagonDimensions

24.030.036.046.055.0

65.0

80.095.0

27.734.641.653.163.575.1

92.4109.6

8724.0 27.787

89100

110133

103

133

133132

133

140

106.4115.0127.0

123.0132.8146.7

'C'Armour/Braid

Orientation2

Orientation1



Armour/Braid'C'

Application

Function

Technical Data


'G' Approx15.0mm

MetricEntry

'B

'

Fem

ale

Entr

y Thr

ead

Mal

e En

try T

hrea

d

Outdoor or Indoor use. Provides a seal onto cable at entry to enclosure via conduit. See technical section of catalogue for installation rules and regulations.

ATEX Cable Gland Ordering ExamplesCable Gland Type/Size/Male Thread/Female Thread e.g. 501/414/C/M32/M32 501/414/C/1" NPT/M32





Provides a seal onto cables outer sheath. Provides female running coupler for conduit entry.


e.g. 501/414/C/M32/M32/S 501/414/C/1" NPT/M32/S



ATEX

International16


CABLE GLAND SELECTION TABLEMale EntryThread Size

Metric

SizeRef. NPT

*

'G'AcrossFlats

AcrossCorners

HexagonDimensions

ABCC2DE

F

M20M25M32M40

M50M63M75

2"

2"3"

11.013.019.025.031.5

42.554.5

14.320.226.532.544.456.368.2

30.036.046.055.0

65.080.095.0

34.669617779105105107

41.653.163.575.192.4109.6

Outer Sheath 'B'

Min. Max.

Alternative thread sizes available. See page 38Accessories including locknuts, sealing washers, shakeproof washers,adaptors and reducers available. See pages 33 - 37


1"1"

""

Female EntryThread Size

Metric NPT*

StandardSeal

AlternativeSeal (S)

8.59.515.522.027.539.048.5

13.415.421.228.034.8

46.558.3

Min. Max.

M20M25M32M40

M50M63M75

-------



Application

Function

Technical Data


'G' Approx15.0mm

MetricEntry

Mal

e En

try T

hrea

d

Fem

ale

Entr

y Thr

ead

Outdoor or indoor use. For particular use with :- Cables that are not substantially compact and circular, have extruded bedding and the fillers, if any, are hygroscopic (eg. not effectively filled).b) Cables that exhibit "Cold Flow"characteristics. See technical section of catalogue for installation rules and regulations.

ATEX Cable Gland Ordering ExamplesCable Gland Type/Size/Male Thread/Female Thread e.g. SB 474/C/M32/M32 SB 474/C/1" NPT/M32

Punch Tool Ordering Example e.g. Punch Tool Number 1.



The required number of holes for the conductors are punched in the seal by means of a special tool to suit the core size. Provides female running coupler for conduit entry.



a)

Provides a barrier seal between the individual insulated cores and prevent entry of the products of an explosion into the cable.


ATEXSB 474

Cable Gland Type

International17


CABLE GLAND SELECTION TABLEMale EntryThread Size

MetricSizeRef. NPT

*

'G'AcrossFlats

AcrossCorners

HexagonDimensions

ABC

M20M25M32

30.036.046.0

34.641.653.1

Alternative thread sizes available. See page 38Accessories including locknuts, sealing washers, shakeproof washers, adaptors and reducers available. See pages 33 - 37


1"

""


Metric NPT*

M20M25M32

CABLE GLAND SIZE CORE SIZE & NUMBER

Maximum No.of Cores

A & B743

1.5 2.5

Cores Cross Sectional Area mm

4.0 6.0 10.0

---

---

--

PUNCH TOOL SIZE DETAILSPunch Ref.

Core C.S.A. mmNo.1 No.1 No.2 No.2 No.31.5 2.5 4.0 6.0 10.0

A & B B & C C B

C

B

696177

---



Application

Function

Technical Data


'G' Approx15.0mm

MetricEntry

Mal

e En

try T

hrea

d

Fem

ale

Entr

y Thr

ead

'D

'

'E

'

To seal conductors at entry to enclosure via conduit or to enable an existing cable gland to be converted to a barrier type cable gland. See technical section of catalogue for installation rules and regulations.

ATEX Cable Gland Ordering ExamplesCable Gland Type/Size/Male Thread/Female Thread e.g. CSB 656/C/M32/M32 CSB 656/C/1" NPT/1" NPT





Allen Grub Screw2mm A/F A-C

2.5mm A/F C2-F

Provides a barrier seal between the individual insulated conductors within the cable or conduit and prevent entry of the products of an explosion into the cable or conduit.The device is fitted with a simple compound filled chamber which permits packing aroundindividual insulated conductors.Assembly of the cable gland compresses and distributes the compound evenly toeffect a barrier seal at the point of entryinto the enclosure. The compound chamber may beseperated from the compound to ensure that the chamber has been effectively filled.Provides female running coupler for cablegland or conduit entry.

Two part sealing compound and assembly instructions are supplied with the cable gland.


ATEXCSB 656

Cable Gland Type

International18




Outdoor or Indoor use. CABLE GLAND SELECTION TABLE

Male EntryThread Size

Metric

SizeRef. NPT

*

'D' AcrossFlats

AcrossCorners

HexagonDimensions

ABC

DEF

C2

M20M25M32M40M50M63M75

M80M90M100

M80M90M100

M40M50M63M75

30.036.046.0

34.641.653.1

Alternative thread sizes available. See page 38Accessories including locknuts, sealing washers, shakeproof washers, adaptors and reducers available. See pages 33 - 37

All Metric entry threads are 1.5mm pitch medium fit.All dimensions in millimetres (except*).

Assembly instruction data sheet No. A.I. 311. For sizes A to F.Assembly instruction data sheet No. A.I. 328. For sizes G to J.

1"1"2"

2"3"

1"2"

2"3"

""


Metric NPT*

M20M25M32 1"

""

Inner Sheath/Cores

Max.OverCores

'E'Max.Inner

Sheath

Max.No.Of

Cores

'G'

55.065.080.095.0

11.016.221.926.337.147.859.062.870.980.3

74.083.093.0

12.518.424.7

29.741.753.566.2

1021426080100120140160180

56585864646468707070

63.575.192.4

109.6

H J

G -

3"4"

-

3"4"

106.4115.0127.0

123.0132.8146.7

Inspectable Compound

501/453 Flameproof / Increased Safety

ICG 653 Flameproof / Increased Safety

153 Industrial general purpose

Armour/Braid'C'

'B

'

'A

'

Entr

y Thr

ead

15.0mm

MetricEntry

Armour/Braid'C'

'B

'

15.0mm

MetricEntry

Armour/Braid'C'

'B

'

'A

'

Entr

y Thr

ead

15.0mm

MetricEntry

Cable Gland Ordering ExamplesCable Gland Type/Size and Armour Type/Thread e.g. 501/453/H/M90 501/453/HX/M90

Cable Gland Ordering ExamplesCable Gland Type/Size and Armour Type/Thread e.g. ICG 653/H/M90 ICG 653/HX/M90

Cable Gland Ordering ExamplesCable Gland Type/Size and Armour Type/Thread e.g. 153/H/M90 153/HX/M90

'D

'

Entr

y Thr

ead

'E

'

InspectableCompound

Flameproof / Increased Safety andIndustrial general purpose

Oversize, G, H & J Cable Glands

501/453 ICG 653 and

ATEX153

International19



Entry ThreadSize

Metric

SizeRef.

NPT

H J

M80M90M100

-

3"4"

Inner Sheath'A'

Min. Max.

Outer Sheath'B' Armour/

Braid

Armour/Braid

Min. Max.

G



Entry ThreadSize

Metric

SizeRef.

NPT

H J

M80M90M100

-

3"4"

Inner Sheath'A'

Min. Max.

Outer Sheath'B'

Min. Max.

G



Entry ThreadSize

Metric

SizeRef.

NPT

H J

M80M90

M100

-

3"4"

Inner Sheath/Cores

Outer Sheath 'B'

G


'D'

'C''G'

'E'Min. Max.

Max.No.Of

Cores

Max.OverCores

Max.Inner

Sheath

'C''G'

Armour/Braid

'C''G'

# Please advise type and size of armour to enable correct clamping rings to be fitted. Assembly instruction data sheet No. A.I. 329.



# Please advise type and size of armour to enable correct clamping rings to be fitted.

# Please advise type and size of armour to enable correct clamping rings to be fitted.

67.067.075.0

73.077.691.6

75.075.088.0

89.589.5104.5

67.067.075.0

73.077.691.6

75.0 121121121

121121121

121121121

75.088.0

89.589.5104.5

62.870.9

80.3

74.083.0

93.0

140160180

75.075.088.0

89.589.5104.5

###

###

###



'G' Approx

'G' Approx

'G' Approx

Application

Function

Technical Data


'G' Approx15.0mm

MetricEntry

'B

'

'A

'

Armour/Braid'C'

Entr

y Thr

ead

Outdoor or Indoor use. For use with single wire armoured 'W', wire braided 'X' and steel tape armoured 'Z' elastomer and plastic insulated cables.

ATEX Cable Gland Ordering ExamplesCable Gland Type/Size/Thread e.g. 351/RAC/C/M32 351/RAC/C/1" NPT

Increased Safety EExe. II 2 GD BASEEFA Certificate No. BAS 01 ATEX 2268X. For sizes Os - F. BASEEFA Certificate No. BAS 01 ATEX 2348X. For sizes G - J. Suitable for use in Zone 1, Zone 2, Zone 21 and Zone 22. Suitable for use in Gas Groups IIA, IIB and IIC.

IP66 ingress protection to IEC 60529 and EN 60529. Operating temperature range -60C to +80C as standard.

Provides armour clamping using one clamping arrangement for all armour/braid types 'W', 'X' and 'Z'. Deluge protection option available. Provides a high pullout resistance and low smoke and fume, zero halogen seal onto the cables outer sheath.


Construction and test standards EN 50014, EN 50019 and 50281-1-1.IEC 60079-0 and IEC 60079-7.


Increased Safety

351/RAC Cable Gland Type

ATEX

International20



Entry ThreadSize

Metric

SizeRef.

NPT*

'G'

AcrossFlats

AcrossCorners

HexagonDimensions

OsOABCC2DE

F

H J

M20M20

M20M25M32M40

M50M63M75

M80M90M100

""

2"

2"3"

-

3"4"

8.011.914.320.226.5

32.544.456.368.2

12.516.922.028.036.046.057.0

20.526.033.041.052.665.3

78.0

24.024.030.036.046.055.0

65.080.095.0

27.727.734.641.653.163.575.192.4109.6

Inner Sheath'A'

Max.

Outer Sheath'B'

Min. Max.

G


5.5 12.09.5 16.0

98

0.9/1.250.9/1.250.9/1.251.25/1.61.6/2.01.6/2.01.8/2.51.8/2.51.8/2.5

0/0.70/0.70/0.70/0.70/0.70/0.70/1.00/1.00/1.0

81818395

105133126134

Alternative thread sizes available. See page 38Alternative non-standard armour clamping rings available. See page 38Accessories including locknuts, sealing washers, shakeproof washers, earth tags, shrouds, adaptors and reducers available. See pages 33 - 37

All Metric entry threads are 1.5mm pitch medium fit. All dimensions in millimetres (except*). Sizes Os and O are available with an M16 thread size. For O size with M16 thread, the maximum cable inner sheath diameter is 10.9mm.# Dedicated armour clamping rings are fitted. Please specify armour type and size. Assembly instruction data sheet No. A.I. 308. For sizes O to F.Assembly instruction data sheet No. A.I. 335. For sizes G to J.

Larger cable glands available in 351 design as shown below.

1"1"

""

###

###

'C'Armour/Braid

Orientation2

Orientation1



121121121

72.080.090.0

75.075.088.0

89.589.5104.5

106.4

115.0127.0

123.0

132.8146.7

Application

Function

Technical Data


'G' Approx15.0mm

MetricEntry

'B

'

Entr

y Thr

ead

Cable Gland Ordering ExamplesCable Gland Type/Size/Thread e.g. 121/C/M32 121/C/1" NPT

IP66, IP67 and IP68 ingress protection to IEC 60529 and EN60529.DTS01 deluge protection certified by ITS.Operating temperature range -60C to +80C as standard.


Construction and test standards EN 50262. BS 6121 Part 1. Type A2.

Outdoor or Indoor use. For use with non-armoured elastomer and plastic insulated cables.

Provides a high pullout resistance seal onto the cables outer sheath.

Industrial general purpose

121 Cable Gland Type

International21



Entry ThreadSize

Metric

SizeRef.

NPT*

'G'

AcrossFlats

AcrossCorners

HexagonDimensions

OsOABCC2DE

F

HJ

M20M20

M20M25M32M40

M50M63M75M80

M90M100

""

2"

2"3"-

3"4"

3.07.5

11.013.019.025.0

31.542.554.5

8.011.914.320.226.532.5

44.456.368.2

8.59.515.522.027.539.048.5

13.415.421.228.034.846.558.3

24.0383938414342585356565656

24.030.036.046.055.0

65.080.095.0

27.727.734.641.653.163.575.192.4109.6

Min. Max.

Outer Sheath 'B'

Min. Max.

G


- -- -

1"1"

""

StandardSeal

AlternativeSeal (S)

- -- -- -


e.g. 121/C/M32/S 121/C/1" NPT/S

67.067.075.0

73.077.691.6

106.4

115.0127.0

123.0

132.8146.7

Alternative entry thread types and sizes available. See page 38Accessories including locknuts, sealing washers, shakeproof washers, shrouds, adaptors and reducers available. See pages 33 - 37




Application

Function

Technical Data


'G' Approx15.0mm

'B

'

Entr

y Thr

ead

MetricEntry

Cable Gland Ordering ExamplesCable Gland Type/Size/Thread e.g. 123/C/M32 123/C/1" NPT

IP66, IP67 and IP68 ingress protection to IEC 60529 and EN 60529.DTS01 deluge protection certified by ITS.Additional deluge protection seal also available.Operating temperature range -60C to +80C as standard.


Construction and test standards EN 50262. BS 6121 Part 1. Type A2.

Outdoor or Indoor use. For use with non-armoured elastomer and plastic insulated cables. May be used on cables incorporating inner and outer cable sheaths.

Provides a high pullout resistant seal onto the cables outer sheath at two independent sealing points.


e.g. 123/C/M32/S 123/C/1" NPT/S

Industrial general purpose

123 Cable Gland Type

International22



Entry ThreadSize

Metric

SizeRef.

NPT*

'G'

AcrossFlats

AcrossCorners

HexagonDimensions

OsOABCC2DE

F

HJ

M20M20

M20M25M32M40

M50M63M75M80

M90M100

""

2"

2"3"-

3"4"

3.07.5

11.013.019.025.0

31.542.554.567.067.075.0

73.077.691.6

8.011.914.320.226.532.5

44.456.368.2

8.59.515.522.027.539.048.5

13.415.421.228.034.846.558.3

24.0676864697273

10098

100100100100

24.030.036.046.055.0

65.080.095.0

27.727.734.641.653.163.575.192.4109.6

106.4

115.0127.0

123.0

132.8146.7

Min. Max.

Outer Sheath 'B'

Min. Max.

G


- -- -

1"1"

""

StandardSeal

AlternativeSeal (S)

- -- -

- -





Application

Function

Technical Data

Materials &