hand protection... · en374-2 resistance to penetration by micro- ... 0 denotes a fail and x...
TRANSCRIPT
3
4
The Personal Protective Equipment Directives (89/686/CEE) and (93/68/CEE) have been enacted by the European Community to ensure harmonisation of regulations regarding testing of all PPE sold within the community.
All gloves of intermediate and complex design must now be tested independently to ascertain their performance and ensure their safety. They must, if they meet these standards, carry a CE Mark on the gloves, or on their packaging when this is not practical.
CATEGORISATIONUnder the terms of the above directive, gloves fall into the following three categories:
CAT I - Simple DesignFor minimal risks only. Suitable only for low risk applications where hazards can be identifi ed by the wearer in time to deal with them.
CAT II - Intermediate DesignReversible risks. Products are type examined by an approved body where they examine the manufacturers technical specifi cations and conduct tests for the relevant standards to ascertain their conformity and/or performance.
CAT III - Complex DesignFor protection against mortal danger or risks of irreversible harm. Products are type examined by an approved body as for category II. In addition, the products and manufacturer are subject to EC quality control according to an approved quality system.
A detailed guide to EN standards is on Page 52
EUROPEAN STANDARDS (ENs)
GENERAL REQUIREMENTS EN420
Defi nes the general requirements for most types of protective gloves including:• Design and construction• Suitability for purpose• Sizing• Comfort and effi ciency• Innocuousness
Ratings
MECHANICAL HAZARDS EN388
a b c d
Resistance to abrasionBlade cut resistanceTear resistancePuncture resistance
0-40-50-40-4
THERMAL (HEAT) HAZARDS EN407
a b c def
Resistance to fl amabilityContact heat resistanceConvective heat resistanceRadiant heat resistanceResistance to small molten metal splashResistance to large molten metal splash
0-40-40-40-40-40-4
ANTISTATIC
New EN1149 standard
No pictogram is to be shown
PassorFail
CHEMICAL AND MICRO-ORGANISMS EN374
EN374-2 Resistance to penetration by micro-organisms.Referred to as acceptable quality level (AQL).
1-3
EN374-3 Resistance to chemical hazards - permeation
1-6
PROTECTION FROM COLD EN511
a. b. c.
Resistance to convective coldResistance to contact coldPermeability of water
0-40-40-1
When scores are given, the higher the score the better the performance. 0 denotes a fail and X denotes no test.
OTHER HAND PROTECTION STANDARDS
FOOD HANDLING
RADIOACTIVE CONTAMINATION
IONISING RADIATION
LOW CHEMICAL RESISTANT
Identifi cation of manufacturer
Size
Glove designation
Approved body number
The CE mark
SKYTECNINJA LITE
9/L
98/0120
CHEMICAL RESISTANCE PERMEATION
In compliance with EN374 Standard, the breakthrough time is given as a permeation index according to the following table:
The breakthrough time (in minutes) of a chemical through the glove is measured in conditions simulating a total immersion of the glove in the chemical at 23˚C. The gloves scoring the highest index have the best resistance to permeation. Index 0 denotes breakthrough time is less than 10 minutes.
Breakthrough timehigher than (in minutes)
10 30 60 120 240 480
Permeation index 1 2 3 4 5 6
5
Skytec offers a wide range of liners and coatings. Compare the strengths of each and choose the compositions that best meet your needs!
NylonA lightweight elastic polyamide which is largely lint-free and washable, dries quickly and is resistant to abrasion and deformation. When mixed with cotton and acrylic, it makes the glove more fl exible and extends its lifetime.
LatexNatural rubber that is supple, elastic, robust, highly resistant to mechanical impacts and hazards. Waterproof and detergent-safe.
Polyurethane (PU)Elastomer that is resistant to wear, abrasion, tearing and harsh oils and chemicals. Does not go hard in the cold or soft in the heat. It is microporous and provides the hand with ventilation. It is very elastic and adapts to all of the hand’s movements.
HPPEHigh performance polyethylene is fl exible, light and durable. As resistant to cutting as a para-aramid but with more resistance to abrasion, the fi bre remains resistant to chemicals, in particular solvents.
NitrileA hard-wearing synthetic polymer. Flexible and can withstand abrasion and puncturing, with maximum resistance to oil with enhanced grip.
CottonNatural Cellulose fi bre. Supple, soft, non-irritating, it provides protection from mechanical hazards, absorbs perspiration and makes continuous wearing of dipped protective gloves very comfortable.
HPTHydropellent Technology coating. The HPT process creates a spongy, soft and durable coating that repels liquids to provide a fi rm wet or dry grip. Encapsulated air molecules provide an inherent vibration absorption feature.
Para-aramidA para-aramid is lightweight, supple, comfortable, and washable. It provides effective protection from cuts, typically levels 4 and 5, and offers durability and performance that far exceeds leather.
APGNew patent pending Neoprene Bi-Polymer coating. Flexible, light and durable it provides great comfort and wearer satisfaction. Rough, chipped fi nish provides excellent grip in dry and wet applications. Solvent free process, silicone free formulation, and protein free. Excellent oil repellency.
NFTNitrile Foam Technology, a unique nitrile foam coating that is made by a Patented manufacturing process, offering breathability and dexterity along with excellent oil and wet grip properties.
Nitrile SpongeA patent pending micro-foam coating with excellent durability, and aiding breathability for long-term comfort. Unique micropore technology limits ingress of oils and greases.
6
APG
APG
APG
APG
Skytec provide the very best in all-round, multi-purpose hand protection, to protect the hand from common mechanical or chemical hazards while preserving mobility and dexterity.
Whether the job calls for small parts handling, general maintenance or heavy lifting and contractor work, we have the best glove for the job.
8
Order No.SKY051SKY052SKY053SKY054
EN388: 2003
Precision operations
Light engineering
Component assembly
Packaging
Warehousing and distribution
Seamless nylon liner with a HPT foam coated palm
Exceptional grip in wet and dry conditions
Foam coating has encapsulated air molecules that provides an inherent cushioning effect
A durable glove with excellent flexibility and tactile touch
Anatomically designed for comfort, dexterity and fit
Breathable back of hand to reduce perspiration and skin irritation
Resistant to abrasion and tearing
Lint free and silicone free
Black colouring to hide soiling
Treated with Actifresh to kill bacteria and promote freshness
9
Order No.SKY061SKY062SKY063SKY064SKY065
Seamless nylon liner with a ¾ HPT foam coating
A ¾ coated version of the Ohio glove for extra durability
Unique HPT foam coating with encapsulated air molecules that provides an inherent cushioning effect
Exceptional grip in wet and dry conditions
Anatomically designed for comfort, dexterity and fi t
Resistant to abrasion and tearing
Durable and cost effective
Lint free and silicone free
Black colouring to hide soiling
Treated with Actifresh to kill bacteria and promote freshness
Precision operations
Light engineering
Component assembly
Packaging
Warehousing and distribution
Oil and gas
EN388: 2003
10
Order No.SKY101SKY102SKY103SKY104SKY105
Construction
Handling rough objects
Wire and cable handling
Handling castings or pre-fabricated metals
Handling steel bars
Cotton liner with a full, crinkle fi nish latex coating
A durable and mechanically strong grip glove, suitable for heavy duty tasks
Excellent grip in wet and dry environments
Abrasion and tear resistance
Comfortable fi t with a knit wrist for extra protection
Anti-bacterial treatment to reduce odours
Blue and red colouring
EN388: 2003
11
Order No.SKY491SKY492SKY493SKY494
Seamless nylon/spandex liner
Anatomically engineered for maximum fi t, superior comfort and dexterity
An Oeko-Tex® certifi ed product
Patented NFTTM nitrile foam palm coating enhances protection
Excellent grip in wet and dry conditions
Enhanced lifecycle through increased resistance to abrasion and tearing
Grey and black aesthetics for extended use
Treated with Actifresh to kill bacteria and promote freshness
Automotive
Quality inspection
Goods handling
Assembly
Maintenance
Light fabrication
EN388: 2003
12
Order No.SKY121SKY122SKY123SKY124SKY125
Precision operations
Optics
Component assembly
Packaging
Printed circuits and electronics
Surveying and Quality Inspection
18gg seamless nylon/lycra liner with a polyurethane coated palm
An ultra-lightweight glove, with exceptional fl exibility and tactile touch for the most delicate of tasks
‘Second skin’ dexterity provides superior sensitivity and comfort
Breathable through front and back of the hand to reduce perspiration and skin irritation
Elasticated wrist for a secure fi t
Lint free, reducing the risk of product contamination
Blue and black colouring
Treated with Actifresh to kill bacteria and promote freshness
EN388: 2003
13
Light engineering
Component assembly
Construction
DIY
Precision operations
Order No.SKY191SKY192SKY193SKY194
Seamless nylon/spandex liner with an ultra-light latex coated palm
The lightweight nylon/lycra liner (15gg) maintains a superthin ‘feel’ for improved dexterity, fi t and comfort
Excellent grip in wet and dry environments
Abrasion and tear resistant
Anatomically designed for high levels of comfort and tactile touch
Breathable back of the hand to reduce perspiration and skin irritation
Elasticated wrist for a secure fi t
Silicone and lint free
Red and grey colouring
Treated with Actifresh to kill bacteria and promote freshness
EN388: 2003
14
Manufacturing
Construction
Assembly
Automotive
General maintenance
Ceiling fi xing
Seamless nylon liner with a PU coated palm
Ideal for precision tasks requiring dexterity and fl exibility
Comfortable with anatomical shaped fi t, allowing excellent freedom of movement and reduction of hand fatigue
Abrasion and tear resistant, with a secure grip
Breathable back of the hand to reduce perspiration and skin irritation
Lint free, reducing the risk of product contamination
Elasticated wrist for a secure fi t
Black colouring to hide soiling
Basalt R Order No.SKY410SKY411SKY412SKY413SKY414SKY415
Quartz Order No.-SKY441SKY442SKY443SKY444Available to order
EN388: 2003
15
Order No.SKY300SKY301SKY302SKY303SKY304SKY305
Manufacturing
Construction
Assembly
Automotive
General maintenance
Seamless nylon liner with a PU coated palm
Ideal for precision tasks requiring dexterity and fl exibility
Comfortable with anatomical shaped fi t, allowing excellent freedom of movement and reduction of hand fatigue
Abrasion and tear resistant, with a secure grip
Breathable back of the hand to reduce perspiration and skin irritation
Lint free, reducing the risk of product contamination
Elasticated wrist for a secure fi t
Grey colouring
EN388: 2003
16
Order No.SKY501SKY502SKY503SKY504
Automotive
Quality Inspection
Goods handling
Assembly and Maintenance
Light fabrication
Handling mild abrasive surfaces
18gg seamless liner glove with solid knit wrist
One of the lightest gloves in the industry for maximum comfort
Patented NFTTM nitrile foam coating for better grip in wet, oily and dry conditions
Excellent resistance to abrasion
Flexible and comfortable
Excellent dexterity
Red colouring
Treated with Actifresh to kill bacteria and promote freshness
EN388: 2003
17
Ultra-lightweight 18gg liner provides unrivalled dexterity and fi t allowing users to wear for longer periods
Rough fi nish provides incredible grip in all environments
Solvent free manufacturing process
Silicone and latex protein free
Exceptional abrasion resistance compared to PU, Foam Nitrile and Latex coatings
Excellent oil repellency
Dark blue and black colouring
Treated with Actifresh to kill bacteria and promote freshness
Order No.SKY531SKY532SKY533SKY534
Precision operations
Light engineering
Component assembly
Packaging
Warehousing and distribution
Oil and gas
Aerospace
Automotive
EN388: 2003
18
Automotive
Aerospace
Precision operations
General assembly
Transport and distribution
Engineering
Order No.SKY011SKY012SKY013SKY014
Seamless nylon liner with a nitrile foam coated palm
Excellent protection and grip in wet, oily and dry environments
Coating works with moisture to provide a superb grip
Anatomically designed for high levels of comfort and dexterity
Offers the user fl exibility and a tactile touch
Breathable back of hand to reduce perspiration and skin irritation
Elasticated wrist for a secure fi t
Silicone free
White and grey colouring
Treated with Actifresh to kill bacteria and promote freshness
EN388: 2003
19
Construction
Automotive assembly
Wire and cable handling
Plastics manufacture
Handling castings or pre-fabrication
Order No.SKY231SKY232SKY233SKY234
Seamless nylon liner with a nitrile coated palm
A secure grip with excellent fl exibility and tactile touch
A durable glove, tear and abrasion resistant
Anatomically designed to follow the natural curve of the hand and help reduce hand fatigue
Elasticated wrist for a secure fi t
Lint free, reducing the risk of product contamination
Anti-bacterial treatment to reduce odours
White and dark green colouring
EN388: 2003
20
Cotton liner with a lightweight nitrile coated palm and knuckles
Durable with an excellent grip
Warm and comfortable to wear
Knitted wrist for a secure fi t
Anti-bacterial treatment to reduce odours
Ideal for dirty tasks
Yellow colouring for increased visibility
EN388: 2003
Construction
Engineering
Maintenance
Public works
Packaging
Neon Order No.SKY241SKY242SKY243SKY244
Neon Xtra Order No.-SKY222SKY223SKY224
More than 80-percent of all hand and arm injuries are due to cuts and lacerations. We make gloves and protective sleeves that not only resist cuts, but are also comfortable to wear, ensuring compliance as well as safety.
High levels of dexterity and grip are also essential in the prevention of cuts. Our pioneering designs and innovations lead the fi eld for these applications with next generation solutions.
22
Engineering
Glass industries
Component assembly
Packaging
Bottling or canning
Ceiling fi xing
Final fi x internal construction work
Seamless HPPE liner with a PU coated palm
A supple and light glove, with level 3 cut and puncture protection
Outstanding fl exibility and tactile touch
Excellent grip in both wet and dry environments
High abrasion and tear resistance
Anatomically designed for comfort, dexterity and fi t
Breathable knitted liner to reduce perspiration and skin irritation
Elasticated wrist for a secure fi t
Mottled grey colouring
Treated with Actifresh to kill bacteria and promote freshness
Cirrus Order No.SKY461SKY462SKY463SKY464
Veritas Order No.SKY451SKY452SKY453SKY454
EN388: 2003
23
Engineering
Glass industries
Final fi x internal construction
Automotive
Metal fabrication
Order No.SKY541SKY542SKY543SKY544
HPPE/lycra liner with APG palm coating
Combined technology offering ultimate precision cut resistant performance
Flexible, light glove providing protection against cuts with high levels of resistance to abrasion and tears
Rough fi nish allows objects and tools to be gripped fi rmly in both dry and wet applications
Solvent and silicone free manufacturing process
Blue and black colouring
Treated with Actifresh to kill bacteria and promote freshness
24
Automotive
Light fabrication
Goods handling
Assembly
Maintenance
Construction
Order No.SKY511SKY512SKY513SKY514
HPPE liner
Sponge nitrile palm coating (patent pending)
Micro-capillaries draw liquids away from the surface providing better grip in all applications
Ventilated liner keeps hand cool to reduce perspiration and skin irritation
Elasticated wrist for a secure fi t
Amber colouring
Treated with Actifresh to kill bacteria and promote freshness
ip
n
EN388: 2003
25
Glass industry
Castings
Sheet metal handling
Automotive
Aerospace
Order No.JSK10HJSK14HJSK18H
Double-ply medium weight sleeve
Para-aramid fi bres in the knit of the sleeve provide cut level 3 resistance
Thumbhole prevents slipping and wrist exposure
Gives increased protection from cuts, slash, tear and certain puncture
Comfortable and protective, the seamless knitted liner avoids skin irritation and is elasticated for extra protection
Machine washable
Available in three lengths: 10”, 14”, 18”
Yellow colouring
EN388: 2003
26
Order No.SKY031SKY032SKY033SKY034SKY035
Engineering
Glass industries
Component assembly
Packaging
Bottling or canning
Seamless nylon/glass fi bre liner with a unique bi-polymer coated palm
A supple and light glove, with cut level 4 resistance
Excellent grip in wet and dry environments
High abrasion and tear resistance
Anatomically designed to follow the natural curve of the hand and help reduce hand fatigue
Breathable back of the hand to reduce perspiration and skin irritation
Silicone free
Elasticated wrist for a secure fi t
Mottled grey and black colouring, suitable for the dirtiest of environments
Treated with Actifresh to kill bacteria and promote freshness
EN388: 2003
27
Seamless HPPE and glass cut resistant liner with an advanced sponge nitrile (patent pending) palm coating
Excellent grip in wet, oily and dry conditions
Anatomically designed for comfort, dexterity and fi t - glove retains fl exibility despite its high protection levels
Breathable back of hand to reduce perspiration and skin irritation
Elasticated wrist for a secure fi t
Green colouring for high visibility
Treated with Actifresh to kill bacteria and promote freshness
Injection moulding
Glass industries
Engineering
Metal fabrication
Transport
Aerospace
Automotive
Precision operations
Order No.SKY521SKY522SKY523SKY524
EN388: 2003
28
Order No.SKY551SKY552SKY553SKY554
HPPE liner with APG palm coating
Maximum cut resistance at cut level 5
Flexible, lightweight glove providing maximum cut protection in dry, oily and greasy environments
Rough fi nish provides excellent grip in all environments
Enhanced durability due to good adhesion to the liner
Silicone and protein free, with a solvent free manufacturing process
Grey and black aesthetics for extended life
Treated with Actifresh to kill bacteria and promote freshness
ry, oily and
ss
Injection moulding
Glass industries
Engineering
Metal fabrication
Transport
Aerospace
Automotive
Precision operations
EN388: 2003
29
Injection moulding
Glass industries
Engineering
Metal fabrication
Transport
Aerospace
Automotive
Precision operations
Seamless HPPE and glass liner with a bi-polymer coated palm
Maximum EN388 mechanical protection of 4-5-4-4
High durability and grip, with tear and abrasion resistance
Excellent grip in wet and dry environments
Superb dexterity and sensitivity - even the most precise of task can be completed
Anatomically designed for comfort, dexterity and fi t, glove retains fl exibility despite its high protection levels
Elasticated wrist for a secure fi t
Grey and black colouring
Treated with Actifresh to kill bacteria and promote freshness
Order No.SKY271SKY272SKY273SKY274SKY275
EN388: 2003
30
Order No.SKY291SKY292SKY293SKY294
Automotive
Mechanical inspection
Paint spraying
Metal fabrication
Transport
Seamless HPPE and glass liner with a PU coated palm
Maximum cut resistance at cut level 5
Excellent grip in wet, oily and dry conditions
High durability with high tear and abrasion resistance
Anatomically designed for comfort, dexterity and fi t, glove retains fl exibility despite its high protection levels
Breathable to reduce perspiration and skin irritation
Elasticated wrist for a secure fi t
Mottled grey colouring
Treated with Actifresh to kill bacteria and promote freshness
EN388: 2003
31
Order No.SKY0222SKY0223SKY0224
Wet and dry glass handling
Glass manufacture including soft coat
Sheet metal handling
Injection or blow moulding
Machine shop work
Automotive
Seamless aramid/glass fi bre liner with leather palm
Lightweight, fl exible glove, para-aramid stitched for durability and strength
Soft, supple leather palm gives a water resistant grip and is suitable for oily conditions
Breathable back of hand to reduce perspiration and skin irritation
Good dexterity and fl exibility together with high cut resistance
Anatomically designed for comfort and fi t
Elasticated wrist
Anti-bacterial treatment to reduce odours
Yellow and grey colouring
EN388: 2003
32
Order No.SKY471SKY472SKY473SKY474
Injection moulding
Glass industries
Engineering
Wet and oily applications
Waste recycling
High risk handling
Fibre-Glass/HPPE liner with a full crinkle latex coating
Cut level 5 for maximum protection
Excellent mechanical performance and durability
Ultra-supple fully coated glove with a crinkled fi nish to ensure maximum grip in wet and dry conditions
The natural latex coating provides protection against oils, lubricants and contaminants
Anatomically designed for comfort, dexterity and fi t - the glove retains fl exibility without reducing high protection levels
Elasticated wrist for a secure fi t
Blue and black colouring
EN388: 2003
33
Order No.SKY042SKY043SKY044
EN388: 2003EN374-3
A K L
EN374-2
Offshore applications
Oil and gas cold storage
Maintenance
Utilities
Packaging
Sheet metal handling
Light or heavy engineering
Glass handling and manufacture
Wire and cable handling
Wet or oily applications
Cut resistant, seamless lined PVC gauntlet with a coral palm/knuckle coating (patent pending)
Cut level 5 resistant, enhanced protection from the double dipped PVC coating and special cut-resistant liner
Maximum durability and grip, with tear and abrasion resistance
Unique coral coating presents the wearer with secure grip in the most extreme environments, including chemical, oils and greases, and wet and dry conditions
Anatomically designed for comfort, dexterity and fi t - glove retains fl exibility despite its level of protection
Black colouring to hide soiling
Treated with Actifresh to kill bacteria and promote freshness
The human body is in a comfortable situation when the heart is beating at a regular speed. This happens at an average blood temperature of 37° C. Using the right cold protection equipment is not a luxury. It will protect the wearer against cold blisters, slipping and excessive cold, while providing a satisfying level of comfort and protection.
Skytec gloves provide unrivalled levels of dexterity and fl exibility while retaining their performance in extreme conditions.
35
Order No.SKY071SKY072SKY073SKY074SKY075
EN388: 2003
Oil industries
Sheet metal handling
Glass industries
Heavy engineering
Paper/cardboard industries
Knitted seamless terry outer with a comfortable oil resistant coated nylon inner liner
Offers excellent protection, the outer absorbs oils to improve grip and feel whilst the inner liner protects against the ingress of contaminants
Excellent heat resistance and protection from the cold
Breathable nylon inner for reduced perspiration and skin irritation
Anatomically designed for comfort and fi t
Elasticated wrist
Knitted grey colouring
Treated with Actifresh to kill bacteria and promote freshness
EN407 EN511
36
Offshore applications
Oil and gas cold storage
Maintenance
Utilities
Packaging
Double insulated nylon liner with a HPT foam ¾ coating
Durable glove that remains fl exible to temperatures as low as –50ºC
Secure grip in wet and dry environments
Additional foam coating across the palm, knuckles and fi ngers provides greater protection even in wet environments
Encapsulated air molecules provide an inherent cushioning effect
Warm and soft lining, anatomically designed for comfort and fi t
Excellent dexterity, fl exibility and durability
Silicone free
Black colouring to hide soiling
Treated with Actifresh to kill bacteria and promote freshness
Order No.SKY082SKY083SKY084
EN388: 2003 EN511
37
Order No.SKY482SKY483SKY484
Utilities
Packaging
Offshore applications
Oil and gas cold storage
Maintenance
Double insulated Nylon liner with full PVC coating
Additional coral palm/knuckle coating (patent pending)
Excellent durability and grip in wet, oily and dry conditions
Durable glove that remains flexible to temperatures as low as -50˚C
Ideal for wet conditions
Enhanced protection from the double-dipped PVC coating
Encapsulated air molecules provide an inherent cushioning effect
Warm and soft lining, anatomically designed for comfort and fit
Silicone free
Black colouring to hide soiling
Treated with Actifresh to kill bacteria and promote freshness
EN388: 2003 EN511
38
18gg seamless liner glove with solid knit wrist
One of the lightest gloves in the industry for maximum comfort
Patented NFTTM nitrile foam palm coating for better grip in wet, oily and dry conditions
Excellent dexterity
Cut level 3 glove with HPPE liner
Sponge nitrile palm coating (patent pending)
Micro-capillaries draw liquids away from the surface providing better grip in all applications
Ventilated liner keeps hand cool to reduce perspiration and skin irritation
Cut level 5 seamless HPPE and glass cut resistant liner with a sponge nitrile palm coating (patent pending)
Excellent grip in wet, oily and dry conditions
Anatomically designed for comfort, dexterity and fi t - glove retains fl exibility despite its high protection levels
Breathable back of hand to reduce perspiration and skin irritation
g)
39
Seamless nylon liner
Tough, fl exible unique patented Coral fi nish coating (patent pending), especially formulated to provide the highest level of grip
Excellent durability and grip in wet, oily and dry conditions
Flared gauntlet for ease of removal
Seamless HPPE liner
Cut level 3
Tough, fl exible unique Coral fi nish coating (patent pending), especially formulated to provide the highest level of grip
Excellent durability and grip in wet, oily and dry conditions
Seamless HPPE liner
Cut level 5
Tough, fl exible unique Coral fi nish coating (patent pending), especially formulated to provide the highest level of grip
Excellent durability and grip in wet, oily and dry conditions
The Tricolore System of gloves and gauntlets is Skytec’s latest development. We continue to strengthen our product offering, and this exciting new range enables you to quickly and efficiently identify the correct glove for the job.
To protect the hands from direct contact with oils, hydrocarbons and corrosive substances, we provide the solutions to whatever conditions you may be working in.
Also of critical importance is the dexterity of the glove and the ability to correctly perform applications whilst wearing the gloves. Skytec have pioneered fl exible high dexterity chemical gloves thereby reducing the risk of chemical related accidents.
41
Order No.GLODAK01GLODAK02GLODAK03GLODAK04
Chemical handling
Petroleum and oil industry
Paintshop applications
Commercial printing
Agriculture and pesticide handling
NBR nitrile unsupported gauntlet
Flock lined for extra comfort and ease of donning
Textured palm and fi ngertips for grip in wet and dry conditions
Resistance to a wide variety of chemicals and solvents
EN374 and Category III approved
Chlorinated and sanitised to reduce odours
Straight cuff, 33cm in length
Green colouring
EN388: 2003 EN374-3 EN374-2
42
35cm gauntlet with a seamless nylon liner
Tough, fl exible unique Coral fi nish coating (patent pending), especially formulated to provide the highest level of grip
Excellent durability and grip in wet, oily and dry conditions
Flared gauntlet for ease of removal
Treated with Actifresh to kill bacteria and promote freshness
35cm gauntlet with a seamless HPPE liner
Cut level 3
Tough, fl exible unique Coral fi nish coating (patent pending), especially formulated to provide the highest level of grip
Excellent durability and grip in wet, oily and dry conditions
Flared gauntlet for ease of removal
Treated with Actifresh to kill bacteria and promote freshness
35cm gauntlet with a seamless double wall HPPE liner
Cut level 5
Tough, fl exible unique Coral fi nish coating (patent pending), especially formulated to provide the highest level of grip
Excellent durability and grip in wet, oily and dry conditions
Flared gauntlet for ease of removal
Treated with Actifresh to kill bacteria and promote freshness
43
Order No.SKY593SKY594
Order No.SKY583SKY584
Chemical handling
Offshore oil and gas
Recycling / waste industry
Bottling and canning
Chemical handling
Offshore oil and gas
Recycling / waste industry
Bottling and canning
Chemical handling
Refining - oil and petrol
Offshore oil and gas
Maintenance
Order No.SKY572SKY573SKY574
EN388: 2003
EN374-3
A K L
EN374-2
EN374-3
A K L
EN374-2
EN374-3
A K L
EN374-2
EN388: 2003
EN388: 2003
44
Refining - oil and petrol
Chemical handling
Agriculture and pesticide handling
Maintenance
100% cotton interlock liner with black APG full hand coating for exceptional grip
Combines the features of several synthetic materials to produce a CAT III gauntlet with true vice-like grip in wet, greasy and chemical envrionments
APG coating provides enhanced performance with greater comfort and wearer satisfaction
Superbly fl exible, comfortable and durable
35cm long gauntlet provides protection from a wide spectrum of chemicals and oils
Silicone and protein free, with a solvent free manufacturing process
Green and black colouring
Treated with Actifresh to kill bacteria and promote freshness
Order No.SKY562SKY563SKY564
EN388: 2003 EN374-3
A K L
EN374-2
45
Order No.SKY042SKY043SKY044
EN388: 2003EN374-3
A K L
EN374-2
Offshore applications
Oil and gas cold storage
Maintenance
Utilities
Packaging
Sheet metal handling
Light or heavy engineering
Glass handling and manufacture
Wire and cable handling
Wet or oily applications
Cut resistant, seamless lined PVC gauntlet with a coral palm/knuckle coating (patent pending)
Cut level 5 resistant, enhanced protection from the double dipped PVC coating and special cut-resistant liner
Maximum durability and grip, with tear and abrasion resistance
Unique coral coating presents the wearer with secure grip in the most extreme environments, including chemical, oils and greases, and wet and dry conditions
Anatomically designed for comfort, dexterity and fi t, glove retains fl exibility despite its level of protection
Black colouring to hide soiling
Treated with Actifresh to kill bacteria and promote freshness
Skytec is one of the most accomplished innovators and manufacturers of disposable hand protection.
Setting the standard for others to follow we continue to lead with high comfort and performance while cost in use remains low.
47
Commercial paint spraying
Petroleum and oil industry
Laboratory work
Emergency services
Chemical applications
High performance NBR nitrile disposable gloves, non-sterile, powder-free
Textured fi nish for grip and touch
Resistant to oils, acids and many chemicals
Category III, EN374 and EN455 approved
Latex free
Comfortable with a ‘second skin’ feel
Signifi cantly stronger alternative to latex
AQL 1.5
Blue colouring
Order No.SKYUTAH1SKYUTAH2SKYUTAH3SKYUTAH4
EN374-3 EN374-2
48
Order No.SKYIRIS1SKYIRIS2SKYIRIS3SKYIRIS4
Commercial paint spraying
Petroleum and oil industry
Laboratory work
Emergency services
Chemical applications
High performance NBR nitrile disposable gloves, non-sterile, powder-free
Strong grip in wet and dry conditions
Resistant to oils, acids and many chemicals
Category III, EN374 and EN455 approved
Latex and powder free to eliminate risk of contamination in food applications
Comfortable with a ‘second skin’ feel
Durable, high performance alternative to latex disposables
AQL 1.5
Rolled cuff for secure fi t
Distinctive colouring
EN374-3 EN374-2
49
Commercial paint spraying
Petroleum and oil industry
Laboratory work
Emergency services
Chemical applications
Premium performance NBR nitrile disposable gloves, non-sterile, powder-free
Textured fi nish for grip and touch
Greater chemical resistance and durability than normal nitrile disposable gloves
Resistant to oils, acids and many chemicals
Category III, EN374 and EN455 approved
Latex free
Comfortable with a ‘second skin’ feel
Up to four times the puncture resistance of latex
AQL 1.5
Green colouring
Order No.SKYTEAL1SKYTEAL2SKYTEAL3SKYTEAL4
EN374-3 EN374-2
50
Product protection
Automotive
Laboratory work
Hair and beauty industry
Chemical applications
High quality, low protein latex disposable gloves, non-sterile
Smooth finish with a high tensile strength
EN455 approved
Comfortable with a ‘second skin’ feel
Beaded cuff
AQL 1.5
Natural colouring
Order No.SKYIOWA1SKYIOWA2SKYIOWA3SKYIOWA4
51
Blue Order No.SKYMICHBL1SKYMICHBL2SKYMICHBL3SKYMICHBL4
Natural Order No.SKYMICHCL1SKYMICHCL2SKYMICHCL3SKYMICHCL4
Food manufacturer and handling
Product protection
Fabrication
Janitorial/Domestic work
High quality vinyl disposable gloves, non-sterile
Smooth finish with a high tensile strength
Comfortable with a ‘second skin’ feel
Powder free
Beaded cuff
AQL 4.0
Food handling approved
Clear and blue colouring available
52
The Single European Act includes a specifi c pledge to improve healthand safety at work for all European workers.
The commitment to ‘level up’ to the best practice currently employedwithin the Union has been enshrined in a legally binding FrameworkDirective (89/391/EEC), which not only lays down broad guidelines forhealth and safety but also places upon the employer an absolute duty“to ensure the safety and health of employees in their workplace”. Thisdirective is amplifi ed by fi ve daughter directives, of which one directlygoverns the use of protective gloves.
The Use of Personal Protective Equipment Directive 89/656/EECFour articles of the Directive merit particular attention, as they placesubstantial responsibilities on employers:
ARTICLE 3 states that before selecting any PPE, a basic assessmentmust be made to identify and evaluate the risk. Where possible, the riskmust be reduced or eliminated by a modifi cation of workplace practice.This option is always to be preferred to the use of PPE.
Under ARTICLE 4, the employer must inform his workers of the risksin the workplace, supply appropriate and correctly fi tting PPE whichcomplies with EU standards, and give adequate instruction in its use.He should further ensure that the PPE is used only for the purposeintended by the manufacturer, and in accordance with themanufacturer’s instructions.
ARTICLE 5 requires the employer to:1. Audit workplace hazards and assess the level of risk to employees.2. Defi ne the properties necessary in the gloves to protect the employees.3. Ensure that all gloves used in the workplace conform to the PPE Directive and relevant EN standards.4. Compare the merits of the various types of protection available.5. Keep full records of assessments and reasons for selecting a particular type of glove. If the risk should alter in any way, for instance by the introduction of a new chemical or industrial process, the assessment must be repeated.
Finally, ARTICLE 6 requires Member States to introduce written rulesfor workplace situations in which the use of PPE shall be consideredcompulsory. Naturally, employers will have to be aware of and complywith these rules.
To comply with the new regulations, you must select gloves which notonly adhere to the above Directive and relevant safety standards, butalso are demonstrably of good quality and fi ttest for the intended task.
COMPLYING WITH THE PPE DIRECTIVE: 89/686/EECThe Directive specifi es two classes of glove meeting two levels of risk:‘Minimal’ and ‘mortal’ or ‘irreversible’ risk. A risk which falls betweenthese two levels may be described as ‘intermediate’. To comply withthe 89/656/EEC Directive, you must establish the level of risk and selectgloves of the appropriate class.
A GREATER COMMITMENT TO HEALTH AND SAFETY EN STANDARDS FOR HAND PROTECTION
A system of marking has been developed to help you in that selection.
Gloves of simple design - for minimal risk onlyFor gloves of simple design offering protection from low level risks, e.g.janitorial gloves, manufacturers are permitted to test and certify glovesthemselves.
Gloves of this category are CE-marked as follows:
Gloves of intermediate design - for intermediate riskGloves designed to protect against intermediate risk, e.g. generalhandling gloves requiring good cut, puncture and abrasion performance,must be subjected to independent testing and certifi cation by a Notifi edBody. Only these approved Bodies may issue a CE mark, without whichthe gloves may not be sold. Each Notifi ed Body has its own identifi cationnumber. The name and address of the Notifi ed Body that certifi es theproduct has to appear on the instructions for use that will accompanythe gloves.
Gloves of intermediate design are CE-marked as follows:
Gloves of complex design - for irreversible or mortal riskGloves designed to protect against the highest levels of risk e.g.chemicals, must also be tested and certifi ed by a Notifi ed Body. Inaddition, the quality assurance system used by the manufacturer toguarantee homogeneity of production must be independently checked.The Body carrying out this evaluation will be identifi ed by a numberwhich must appear alongside the CE mark (in this case, 0120).
Gloves of complex design are CE-marked as follows:
Please note that the original PPE Directive 89/686/EEC has beenamended by both the 93/95/EEC Directive and the CE MarkingDirectives 93/68/EEC and 95/58 EEC.
RAISING STANDARDS IN EUROPEThe primary aim of the Personal Protective Equipment Directive is toimprove safety at work. This is achieved by establishing standards formanufacture and use that will apply throughout the Union; and thisis the remit of the Committee for European Normalisation (CEN). Thecommittee is made up of representatives of the national standardsorganisations in each of the Member States plus EFTA, along with majorEuropean PPE manufacturers.
If you would like any further clarifi cation of these Directives, or furtherinformation on testing and certifi cation procedures, please contact ourTechnical Service.
0120
53
SCOPEThis standard defi nes the general requirements for glove designand construction, innocuousness, comfort, effi ciency, marking andinformation applicable to all protective gloves. This standard can also apply to arm guards. The key points are given below. Some gloves designed for very specialist applications, such as electrician’s or surgical gloves are governed by other stringent job-specifi c standards (Details are available on request).
DEFINITIONA glove is an item of personal protective equipment which protects the hand or any part of the hand from hazards. It may also cover part of the forearm and arm. A performance level is a number (between 0 and 4) which shows how a glove has performed in a specifi c test, and by which the results of that testing may be graded. Level 0 indicates that the glove is either untested or falls below the minimum performance level. A performance level X means that the testing method is not suitable for the glove sample. Higher numbers indicate higher levels of performance.
GLOVE CONSTRUCTION AND DESIGN• Gloves have to offer the greatest degree of protection in the foreseeable conditions of end use.• When seams are included, the strength of these seams should not reduce the overall performance of the glove.
INNOCUOUSNESS• The gloves themselves shouldn’t cause any harm to the user• PH of the glove should be between 3.5 and 9.5• Chromium (VI) content should be below detection (<10 ppm)• Natural rubber gloves shall be tested on extractable proteins as per EN 455-3.
CLEANING INSTRUCTIONS• If care instructions are provided, the levels of performance should not be reduced after the maximum recommended number of cleaning cycles.
ELECTROSTATIC PROPERTIES• Antistatic gloves that are designed to reduce the risk of electrostatic discharges shall be tested as per EN 1149• Obtained test values are to be reported on the Instructions for Use• An electrostatic pictogram shall NOT be used
SIZING (SEE TABLE BELOW)• Gloves that are below the minimum length are to be called ‘Fit for Special Purpose’.
STANDARD EN 420: 2003GENERAL REQUIREMENTS FOR PROTECTIVE GLOVES
DEXTERITY• If required, performance to be graded as per table at the foot of the page.
WATER VAPOUR TRANSMISSION AND ABSORPTION• If required, gloves shall allow water vapour transmission (5mg cm2.h)• If gloves exclude water vapour transmission, it should be at least 8mg/cm2 for 8 hours.
MARKING & INFORMATION:Marking of the glove• Each glove should be marked with: - Name of manufacturer - Glove and size designation - CE mark - Appropriate pictograms accompanied by the relevant performance levels and the reference of the EN standard.
• The marking should be legible throughout the life of the glove. Where marking of the glove is not possible in view of the characteristics of the glove, it should be mentioned on the fi rst packaging enclosure.
Marking of the packaging immediately containing the gloves• Name and address of the manufacturer or representative• Glove and size designation• CE mark• Usage info - Simple design: “for minimal risks only” - Intermediate design or complex design: relevant pictograms - When protection is limited to part of the hand, this shall be mentioned (e.g. “Palm Protection style only”)• Reference to where information can be obtained
Instructions for Use (To be supplied when the glove is placed on the market)• Name and address of the manufacturer or representative• Glove designation• Size range available• CE mark• Care and storage instruction• Instructions and limitations of use• A list of substances used in the glove which are known to cause allergies• A list of all substances in the glove shall be made available upon request• Name and address of Notifi ed Body that certifi ed the product
SIZING OF GLOVESGlove size Fits hand size Hand circumference/length (mm) Minimum length of the glove (mm)
6 6 152/160 2207 7 178/171 2308 8 203/182 2409 9 229/192 25010 10 254/204 26011 11 279/215 270
Performance level Smallest diameter of pin that can be picked up with gloved hand 3 times/30 seconds (mm)1 11.02 9.53 8.04 6.55 5.0
54
SCOPEThis standard applies to gloves to protect from Ionising Radiation andRadioactive Contamination.
DEFINITION AND REQUIREMENTSThe nature of protection is shown by a pictogram relating to the specifi c protective qualities.• To protect from radioactive contamination, the glove has to be liquidproof and needs to pass the penetration test defi ned in EN 374.
STANDARD EN 421: 1994GLOVES GIVING PROTECTION FROM RADIOACTIVE CONTAMINATION AND IONISING RADIATION
• For gloves used in containment enclosures, the glove shall offer high resistance to permeability of water vapour.• To protect from ionising radiation, the glove has to contain a certain amount of lead, quoted as “lead equivalence”. This Lead Equivalence must be marked on each glove.• Materials exposed to ionising radiation may be modelled by their behaviour to ozone cracking. This test is optional and can be used as an aid to selecting gloves which require resistance to ionising radiation.
SCOPEThis standard applies to all kinds of protective gloves in respect ofphysical and mechanical aggressions caused by abrasion, blade cut,puncture and tearing.
DEFINITION AND REQUIREMENTSProtection against mechanical hazards is expressed by a pictogram followed by four numbers (performance levels), each representing test performance against a specifi c hazard.
STANDARD EN 388: 2003GLOVES GIVING PROTECTION FROM MECHANICAL RISKS
The ‘Mechanical Risks’ pictogram is accompanied by a 4-digit code:
a. Resistance to abrasion Based on the number of cycles required to abrade through the sample given.
b. Blade cut resistance Based on the number of cycles required to cut through the sample at a constant speed.
c. Tear resistance Based on the amount of force required to tear the sample.
d. Puncture resistance Based on the amount of force required to pierce the sample with a standard sized point.
In all cases, (0) indicates the lowest level of performance, as follows:
a b c d
EN388 TEST PERFORMANCE LEVEL RATING:0 1 2 3 4 5
a. Abrasion resistance (cycles) < 100 100 500 2000 8000
b. Blade cut resistance (factor) < 1.2 1.2 2.5 5.0 10.0 20.0
c. Tear resistance (newton) < 10 10 25 50 75
d. Puncture resistance (newton) < 20 20 60 100 150
These performance levels must be prominently displayed alongside the pictogram on the packaging which immediately contains the gloves.
55
SCOPEThis standard specifi es the capability of gloves to protect the useragainst chemicals and/or micro-organisms.
DEFINITIONS:PenetrationThe movement of a chemical and/or micro-organism through porousmaterials, seam, pinholes or other imperfections in a protective glovematerial at a non-molecular level.
PermeationThe rubber and plastic fi lms in gloves do not always act as barriers to
The ‘Chemical resistant’ glove pictogram must be accompanied by a 3-digit code. This code refers to 3 chemicals (from a list of 12 standard defi ned chemicals) for which a breakthrough time of at least 30 minutes has been obtained.
The ‘Low Chemical resistant’ or ‘Waterproof’ glove pictogram is to be used for those gloves that do not achieve a breakthrough time of at least 30 minutes against at least three chemicals from the defi ned list, but which comply with the Penetration test.
The ‘Micro-organism’ pictogram is to be used when the glove conforms to at least a performance level 2 for the Penetration test.
Warning: The chemical data information does not necessarily refl ect the actual duration in the workplace.
Permeation: Each chemical tested is classifi ed in terms of breakthrough time (performance level 0 to 6):
STANDARD EN 374: 2003GLOVES GIVING PROTECTION FROM CHEMICALS AND MICRO-ORGANISMS
liquids. Sometimes they can act as sponges, soaking up the liquidsand holding them against the skin. It is therefore necessary to measurebreakthrough times, or the time taken for the hazardous liquid to comein contact with the skin.
REQUIREMENTS• The minimum liquid proof section of the glove shall be at least equal to the minimum length of the glove specifi ed in EN 420.• Penetration: A glove shall not leak when tested to an air and/or water leak test, and shall be tested and inspected in compliance with the Acceptable Quality Level.
AQL: Performance level Acceptable quality level unit Inspection levels
Level 3 < 0.65 G1
Level 2 < 1.5 G1
Level 1 < 4.0 S4
Code Chemical CAS Number Class
A Methanol 67-56-1 Primary alcohol
B Acetone 67-64-1 Ketone
C Acetonitrile 75-05-8 Nitrile compound
D Dichloromethane 75-09-2 Chlorinated paraffi n
E Carbone disulphide 75-15-0 Sulphur containing Organic compound
F Toluene 108-88-3 Aromatic hydrocarbon
G Diethylamine 109-89-7 Amine
H Tetrahydrofurane 109-99-9 Heterocyclic and Ether compound
I Ethyl acetate 141-78-6 Ether
J N-Heptane 142-85-5 Saturated Hydrocarbon
K Sodium hydroxide 40% 1310-73-2 Inorganic base
L Sulphuric acid 96% 7664-93-9 Inorganic mineral acid
Measured breakthrough time Protection Index Measured breakthrough time Protection Index
> 10 minutes Class 1 > 120 minutes Class 4
> 30 minutes Class 2 > 240 minutes Class 5
> 60 minutes Class 3 > 480 minutes Class 6
A B C
56
SCOPEThis standard applies to any gloves to protect the hands againstconvective and contact cold down to -50oC.
DEFINITION AND REQUIREMENTSProtection against cold is expressed by a pictogram followed by a seriesof 3 performance levels, relating to specifi c protective qualities.The ‘cold hazard’ pictogram is accompanied by a 3-digit number:a. Resistance to convective cold (performance level 0 - 4)
b. Resistance to contact cold (performance level 0 - 4)
c. Permeability by water (0 or 1)
STANDARD EN 511: 1994GLOVES GIVING PROTECTION FROM COLD
All gloves must achieve at least EN388 performance level 1 for abrasionand tear.
• Convective cold resistance: based on the thermal insulation properties of the glove which are obtained by measuring the transfer of cold via convection.
• Contact cold resistance: based on the thermal resistance of the glove material when exposed to contact with a cold object.
• Water impermeability: 0 = water penetration after 30 minutes of exposure 1 = no water penetration.
A B C
SCOPEThis standard specifi es thermal performance for protective glovesagainst heat and/or fi re.
DEFINITION AND REQUIREMENTSThe nature and degree of protection is shown by a pictogram followed by a series of six performance levels, relating to specifi c protective qualities. Gloves must also achieve at least Performance level 1 for abrasion and tear.
The ‘heat and fl ame’ pictogram is accompanied by a 6-digit number:
a. Resistance to fl ammability (performance level 0-4) Based on the length of time the material continues to burn and glow after the source of ignition is removed. The seams of the glove shall not come apart after an ignition time of 15 seconds.
b. Contact heat resistance (performance level 0-4) Based on the temperature range (100-500oC) at which the user will feel no pain for at least 15 seconds. If an EN level 3 or higher is obtained, the product shall record at least EN level 3 in the fl ammability test Otherwise, the maximum contact heat level shall be reported as level 2.
STANDARD EN 407: 2004GLOVES GIVING PROTECTION FROM THERMAL HAZARDS
c. Convective heat resistance (performance level 0-4) Based on the length of time the glove is able to delay the transfer of heat from a fl ame. A performance level shall only be mentioned if a performance level of 3 or 4 is obtained in the fl ammability test.
d. Radiant heat resistance (performance level 0-4) Based on the length of time the glove is able to delay the transfer of heat when exposed to a radiant heat source. A performance level shall only be mentioned if a performance level 3 or 4 is obtained in the fl ammability test.
e. Resistance to small splashes of molten metal (performance level 0-4) The number of molten metal drops required to heat the glove sample to a given level. A performance level shall only be mentioned if a performance level 3 or 4 is obtained in the fl ammability test.
f. Resistance to large splashes of molten metal (performance level 0-4) The weight of molten metal required to cause smoothing or pinholing across a simulated skin placed directly behind the glove sample. The test is failed if metal droplets remain stuck to the glove material or if the specimen ignites.
a b c d e f
EN420 StandardThe way the glove fi ts the user is a crucial factor in the dexterity of the working hand. Here is all the information you need to make the right choice.
Testing prior to usingIf the glove is too small, it cuts off the blood circulation and restricts the movement of the hand. On the contrary, loose gloves slip off at the slightest movement and make your handling very imprecise. To be sure of your size and fi t contact Skytec.
Glove size further to EN420
Hand (mm) Glove
Palm circumference Length Minimum Length
6 152 160 220
7 178 170 230
8 203 182 240
9 229 192 250
10 254 204 260
11 279 215 270
57
Individual useTo prevent any risk of microbial, organic or chemical contamination, use of any glove should be ‘personal’ and not shared with other wearers, even after washing. (European directive 89/656/EEC).
Checking wearEach user must carefully monitor the condition of their gloves and replace them as soon as they lose the properties required for the task undertaken. This is notably the case for chemical protection gloves, which may show signs of excessive softening, becoming porous, brittle or displaying cracks when in contact with corrosive substances. This is normal but potentially harmful to hands, therefore precautions must be taken. (See box opposite).
WashingSkytec gloves can be washed at 40°C with a neutral detergent (pH ≥ 5), but the machine should not be fi lled completely as this affects the removal of soiling. Mechanical and/or chemical resistant properties typically remain after three washes but this depends on the degree of wear to the glove which must be checked.
Before putting on the gloves, wash and dry your hands carefully.
In the event of prolonged use, do not use gloves beyond the recommended exposure time as highlighted within a COSHH assessment.
Regularly check that the gloves have not become porous or are displaying any signs of degradation.
Where appropriate, folding the sleeve of the glove over slightly can help prevent substances coming into contact with arms.
Before removing gloves follow the advice on the user instructions.
When removing the second glove, do not touch the outside with the bare hand, but grip it by the inside of the sleeve. (Glove removal protocols are available from Globus upon request).
Before reusing gloves, check that they are dry both inside and out.
Your LogoYour DetailsYour Glove Range
A range of high-quality hand protection posters and charts, customised with your logo, details and product range - a genuine aid to worker compliance.
A Globus hand protection expert is available to assess your applications and current protection to provide guidance, advice and product evaluation without any requirement for commitment. This is a quick and easy way to validate or ensure the most suitable products are being utilised to deliver workers’ safety.
Globus will visit your workplace and conduct a comprehensive survey report. This will highlight areas of potential improvement, cost saving as well as developing a personalised plan that will incorporate all your aspirations, be they injury reduction, cost control or enhancing your ‘green’ credentials.
58
59
© 2012 Globus (Shetland) Ltd. This catalogue replaces all previously published catalogues and is the exclusive property of Globus (Shetland) Ltd. It may not be copied, duplicated or reproduced by any means without our expressed, written permission.
Globus (Shetland) Ltd, Globus Building, 38 Wheel Forge Way, Trafford Park, Manchester, M17 1EHwww.globus.co.uk