hammer strength equipment plab-a00, - … loaded... · page 2 of 17 hammer strength equipment plab...
TRANSCRIPT
WEIGHT = 309 lbLENGTH = 56"WIDTH = 57 5/8"HEIGHT = 65 7/8"
PAGE 1 OF 17
HAMMER STRENGTH EQUIPMENT
PLAB-A00,
PAGE 2 OF 17
HAMMER STRENGTH EQUIPMENT
PLAB EXPLODED
B
619
2
10
28
9
15
7
7
4
21
9 8
117
99
28
20
5
22
13
25
23
17
26
24
14
17
16
1
7
6
3
9
8
11
27
18
19
NOTE: 1. WHEN ATTACHING RODENDSBOLT HEAD IS ON RODEND SIDE IN ALL CASES.2. WHEN INSTALLING #13, YOU MUST LIFT THE REARRELEASE HANDLE SO THE ASSEMBLY WILL GO FARENOUGH ON THAT THE REAR ROLLER CAN BEINSTALLED.
ITEM NO. QTY. PART NO. DESCRIPTION
1 1 PLAB-CHX-0 ASSY, PLAB, BOTTOM X-MEM
2 1 PLAB-CRSF-0 ASSY, PLAB, RIGHT SIDE FRAME
3 1 PLAB-CLSF-0 ASSY, PLAB, LEFT SIDE FRAME
4 1 PLAB-CMAT-0 ASSY, PLAB, TOP WORKARM
5 1 PLAB-CMAB-0 ASSY, PLAB, BOTTOM WORKARM
6 26 WASH.5STAR 1/2" INTERNAL LOCK WASHER
7 24 NUT.5LOCK 1/2 DIA THICK LOCK NUT
8 22 H-BACK-WASH BACKING WASHER
9 22 HHB.5X3 1/2 X 3 BOLT
10 1 PLAB-CTX-0 ASSY, PLAB, TOP X-MEM
11 4 HHB.5X4 1/2 X 4 BOLT
12 4 NUT.5JAMLOCK 1/2 THIN LOCK NUT
13 1 PLAB-CSM-0 ASSY, PLAB, ADJ. ROLLER SEAT
14 1 PLAB-CST-0 ASSY, PLAB, SEAT PAD MOUNT
15 1 PLAB-BX-0 WLDMT, PLAB, REAR X-MEM
16 8 WASH.375SAE 3/8" SAE FLAT WASHER
17 8 3236204 SCREW, M10 X1.5 35MM
18 2 3236210 SCREW, M10 X1.5 65MM
19 2 HHB.5X2.5 1/2 X 2 1/2 BOLT
20 1 U-PLAB PAD, PLAB SEAT
21 1 7499301 PAD, 13-3/4 X 10 -3/4
22 1 7399300 PAD. 7 X 11-1/4
23 2 7424701 ASSY, ROLLER PAD - SHORT
24 2 7357901 SHAFT COLLAR, 1-1/2" ID ALUM
25 2 7308701 CAP, BEARING HOUSING
26 2 7322301 PLATE, 1.97 OD X .44 ID 10GA
27 1 LP-EX-SPRNG LEG PRESS EXTENSION SPRING
28 3 H-HORN-ASSY ASSY, WEIGHT HORN
SCALE 1 : 8DETAIL B
NOTE: BOLT HEADON BEARING SIDEINSTALL #4 AND #5BEFORE INSTALLING#10
WEIGHT = 10.8lbLENGTH = 30"WIDTH = 6" HEIGHT = 3 3/4"
PAGE 3 OF 17
HAMMER STRENGTH EQUIPMENT
PLAB-CHX-0, "ASSY, PLAB, BOTTOM X-MEM
4
3
2
5
6
ITEM NO. QTY. PART NO. DESCRIPTION
2 1 H-BUMP-SML SMALL BUMPER (VEN# MM3)
3 2 WASH.5STAR 1/2" INTERNAL LOCK WASHER
4 2 NUT.5LOCK 1/2 DIA THICK LOCK NUT
5 2 WASH.5SAE 1/2" SAE FLAT WASHER
6 2 HHB.5X3 1/2 X 3 BOLT
WEIGHT = 56.2 lbLENGTH = 38 1/8"WIDTH = 12"HEIGHT = 44"
PAGE 4 OF 17
HAMMER STRENGTH EQUIPMENT
PLAB-CRSF-0, "ASSY, PLAB, RIGHT SIDE FRAME
2
9
14
13
5
16
10
11
2
8
6
12
2
11
1057
2
15
3
5
4BOLT HEADS ON BEARING SIDE
NOTE: #12 IS SHIPPEDUNINSTALLED. #4 AND #5 AND #10ON "EXPLODE" PAGE MUT BE INSTALLEDBEFORE INSTALLING #12
ITEM NO. QTY. PART NO. DESCRIPTION
2 4 RC1530-1Q1 CAP:1-1/2 X 3 RECTANGLE PLUG
3 4 HHB.5X3 1/2 X 3 BOLT
4 4 H-BACK-WASH BACKING WASHER
5 6 NUT.5LOCK 1/2 DIA THICK LOCK NUT
6 2 WASH.5SAE 1/2" SAE FLAT WASHER
7 2 WASH.5STAR 1/2" INTERNAL LOCK WASHER
8 2 HHB.5X4.5 1/2 X 4 1/2 BOLT
9 2 MM-9 3 X 6 FLANGE RUBBER SLIPPER
10 2 H-BEAR-SML SMALL BEARING
11 2 ACCORDIAN SHAFT GUARD
12 1 H-BUMP-MED MM2 MEDIUM
13 1 H-NAME PLATE NAMEPLATE (45156-P)
14 1 NONSKID 1 X 9 PLASTIC NON SKID STRIP 1 X 9
15 1 PLAB-CCRANK-0 ASSY, PLAB, CRANK
16 1 8039501 LABEL, WARNING,TRIANGLE
WEIGHT = 38.46 lbLENGTH = 38 1/8"WIDTH = 6 3/4"HEIGHT = 44"
PAGE 5 OF 17
HAMMER STRENGTH EQUIPMENT
PLAB-CLSF-0, "ASSY, PLAB, LEFT SIDE FRAME
3
2
7
6
5
4
3
4
5
QTY. PART NO. DESCRIPTION
2 2 MM-9 3 X 6 FLANGE RUBBER SLIPPER
3 2 RC1530-1Q1 CAP:1-1/2 X 3 RECTANGLE PLUG
4 2 ACCORDIAN SHAFT GUARD
5 2 H-BEAR-SML SMALL BEARING
6 1 H-NAME PLATE NAMEPLATE (45156-P)
7 1 NONSKID 1 X 9 PLASTIC NON SKID STRIP 1 X 9
WEIGHT = 51.8 lbLENGTH = 57 1/2"WIDTH = 41 3/16"HEIGHT = 20 3/4"
PAGE 6 OF 17
WEIGHT =LENGTH =WIDTH =HEIGHT =
PAGE 6 OF 17
WEIGHT =LENGTH =WIDTH =HEIGHT =
PAGE 6 OF 17
HAMMER STRENGTH EQUIPMENT
PLAB-CMAT-0, "ASSY, PLAB, TOP WORKARMHAMMER STRENGTH EQUIPMENT
PLAB-CMAT-0, "ASSY, PLAB, TOP WORKARMHAMMER STRENGTH EQUIPMENT
PLAB-CMAT-0, "ASSY, PLAB, TOP WORKARM
10
6
2
3
7
2
8
9
5
4
3
11
13
1412
12
NOTE: BOLT HEAD ONRODEND SIDE
ITEM NO. QTY. PART NO. DESCRIPTION
2 2 RUBCAP1-2 RUBBER CAP #1
3 5 RC1530-1Q1 CAP:1-1/2 X 3 RECTANGLE PLUG
4 1 RC1520-1Q1 CAP:1-1/2 X 2 RECTANGLE PLUG
5 2 H-GRIP HANDLE GRIPS (.938X16)
6 1 H-RUBRNG MM5 RING
7 1 SELECTOR PIN-3 SELECTOR PIN 3 IN.
8 1 IDAB PRODUCT DECAL
9 1 8773701 ASTM LABEL10 1 MAX WEIGHT 25 LB MAX WEIGHT 25lb
11 1 PLAB-CSLINK-0 ASSY, PLAB, SHORT LINK
12 2 WASH.5STAR 1/2" INTERNAL LOCK WASHER
13 1 HHB.5X4.5 1/2 X 4 1/2 BOLT
14 1 NUT.5JAMLOCK 1/2 THIN LOCK NUT
15 4 H-HPLUG (REG) 9/16IN HOLE PLUG
WEIGHT = 3.06 lbLENGTH = 21 7/8"WIDTH = 1 5/16"HEIGHT = 1"
PAGE 7 OF 17
HAMMER STRENGTH EQUIPMENT
PLAB-CSLINK-0, "ASSY, PLAB, SHORT LINK
2
3
3
2
FROM RODEND BASE TO RODEND BASE
16 3/16"
INITIAL LENGTH
NOTE: WHEN ATTACHING RODENDSBOLT HEAD IS ON RODEND SIDE IN ALL CASES
ITEM NO. QTY. PART NO. DESCRIPTION
2 2 ROD END.5 .375 RT. TH. Hyme j
3 2 NUT 1-2 X 20 PLAIN 1/2IN JAM NUT FINE
WEIGHT = 6.705 lbLENGTH = 9"WIDTH = 10 13/16"HEIGHT = 4 7/16"
PAGE 8 OF 17
HAMMER STRENGTH EQUIPMENT
PLAB-CCRANK-0, "ASSY, PLAB, CRANK
2
3
3
2
ITEM NO. QTY. PART NO. DESCRIPTION
2 2 H-BEAR-SML SMALL BEARING
3 2 ACCORDIAN SHAFT GUARD
2
3
3
2
ITEM NO. QTY. PART NO. DESCRIPTION
2 2 ROD END.5 .375 RT. TH. Hyme j
3 2 NUT 1-2 X 20 PLAIN 1/2IN JAM NUT FINE
WEIGHT = 3.56 lbLENGTH = 24 9/16"WIDTH = 1 5/16"HEIGHT = 1"
PAGE 9 OF 17
HAMMER STRENGTH EQUIPMENT
PLAB-CLLINK-0, "ASSY, PLAB, LONG LINK
NOTE: WHEN ATTACHING RODENDSBOLT HEAD IS ON RODEND SIDE IN ALL CASES
FROM RODEND BASE TO RODEND BASE
18 5/8"
INITIAL LENGTH
WEIGHT = 45.8 lbLENGTH = 31"WIDTH = 14 1/8"HEIGHT = 30"
PAGE 10 OF 17
HAMMER STRENGTH EQUIPMENT
PLAB-CMAB-0, "ASSY, PLAB, BOTTOM WORKARM
9
10
7
3
54
82
12
13
14
13
15
16
ITEM NO. QTY. PART NO. DESCRIPTION
2 1 7564401 SEATRACK, FLAT
3 1 8416801 SEATRACK, SERRATED
4 1 3235802 GRIP, SHADOW GRAY, 1.5"
5 1 7570601 STOP, ROLLER SEAT
6 1 3238318 M10x1.5x110mm
7 1 3236218 SCREW, M10 X1.5 110MM
8 1 3236801 NUT, M10 HEX NYLOCK SS
9 2 RC1520-1Q1 CAP:1-1/2 X 2 RECTANGLE PLUG
10 1 RC-2030-1 CAP, END 2 X 3
11 1 SERIAL NUMBER SERIAL NUMBER
12 1 PLAB-CLLINK-0 ASSY, PLAB, LONG LINK
13 2 WASH.5STAR 1/2" INTERNAL LOCK WASHER
14 1 HHB.5X3 1/2 X 3 BOLT
15 1 NUT.5JAMLOCK 1/2 THIN LOCK NUT
16 1 7422002 LABEL, SEAT ADJUST
8
4
5
7
6
2
3
9
9
9
9
10
10
ITEM NO. QTY. PART NO. DESCRIPTION
2 2 WASH.5SAE 1/2" SAE FLAT WASHER
3 2 NUT.5JAMLOCK 1/2 THIN LOCK NUT
4 2 WASH.5STAR 1/2" INTERNAL LOCK WASHER
5 2 HHB.5X3 1/2 X 3 BOLT
6 1 H-BUMP-SML SMALL BUMPER (VEN# MM3)
7 2 RC1530-1Q1 CAP:1-1/2 X 3 RECTANGLE PLUG
8 1 PATENT PATENT DECAL
9 4 H-HPLUG (REG) 9/16IN HOLE PLUG
10 2 8039501 LABEL, WARNING,TRIANGLE
WEIGHT = 17.9 lbLENGTH = 38 3/4"WIDTH = 12 1/2"HEIGHT = 6"
PAGE 11 OF 17
HAMMER STRENGTH EQUIPMENT
PLAB-CTX-0, "ASSY, PLAB, TOP X-MEM
WEIGHT = 20.87 lbLENGTH = 22 7/16"WIDTH = 12 3/4"HEIGHT = 6 7/8"
PAGE 12 OF 17
HAMMER STRENGTH EQUIPMENT
PLAB-CSM-0, "ASSY, PLAB, ADJ. ROLLER SEAT
NOTE POSITION OF TORSION SPRING
SIDE PLATE AND DECAL REMOVED FOR VIEW
2
3
4
9
8
65
10
8
7
12
ITEM NO. QTY. PART NO. DESCRIPTION
2 3 7564201 ASSY, SEAT ROLLER
3 1 8417301 WLDMT, SEAT HANDLE
4 5 3236217 SCREW, M10 X1.5 100MM
5 5 3236601 WASHER, 3/8 SAE SS
6 5 3236801 NUT, M10 HEX NYLOCK SS
7 1 7442701 SPRNG, PRO2 HANDLE TORSION
8 2 H-BEAR-SML SMALL BEARING
9 2 HHB.5X2.5 1/2 X 2 1/2 BOLT
10 2 NUT.5LOCK 1/2 DIA THICK LOCK NUT
11 1 3238502 CAP, 1/2 X 3
12 1 7422001 LABEL, SEAT INST
WEIGHT = 13.75 lbLENGTH = 21 5/16"WIDTH = 12 3/4"HEIGHT = 10 5/8"
PAGE 13 OF 17
HAMMER STRENGTH EQUIPMENT
PLAB-CST-0, "ASSY, PLAB, SEAT PAD MOUNT
3
2
2
3
2
5
NOTE THE POSITION OFTHE TORSION SPRING
ITEM NO. QTY. PART NO. DESCRIPTION
2 3 RC1520-1Q1 CAP:1-1/2 X 2 RECTANGLE PLUG
3 2 7347301 NUT, SPIDER M10 X 1.5
4 2 H-PLATE-G1 SMALL PLATE GUARD
5 1 PLAB-CSRH-0 ASSY, PLAB, SEAT RELEASE HANDLE
6 2 WASH.5STAR 1/2" INTERNAL LOCK WASHER
7 1 NUT.5LOCK 1/2 DIA THICK LOCK NUT
8 1 HHB.5X3.5 1/2 X 3 1/2 BOLT
9 1 7442701 SPRNG, PRO2 HANDLE TORSION
WEIGHT = 3.8 lbLENGTH = 11 1/8"WIDTH = 5 9/16"HEIGHT = 3 3/8"
PAGE 14 OF 17
HAMMER STRENGTH EQUIPMENT
PLAB-CSRH-0, "ASSY, PLAB, SEAT RELEASE HANDLE
2
ITEM NO. QTY. PART NO. DESCRIPTION
2 1 H-GRIP-75 STANDARD 3/4" BICYCLE GRIP
WEIGHT = 19.73 lbLENGTH = 35 1/4"WIDTH = 9 1/2"HEIGHT = 2"
PAGE 15 OF 17
HAMMER STRENGTH EQUIPMENT
PLAB-BX-0, "WLDMT, PLAB, REAR X-MEM
WEIGHT = 3 1/4 lbLENGTH = 8 5/8"WIDTH = 6"HEIGHT = 3"
PAGE 16 OF 17
HAMMER STRENGTH EQUIPMENT
H-HORN-ASSY, "ASSY, WEIGHT HORN
2
3
ITEM NO. QTY. PART NO. DESCRIPTION
2 1 8078001 CAP, END 1.75 DIA RD 14-20 GA
3 1 H-RUBRNG MM5 RING
HAMMER STRENGTH EQUIPMENT
NOTES
HORIZONTAL X-MEM TOP OF
SEAT
NOTE: BEFORE TIGHTENING SEAT BEARINGBOLTS, MAKE SURE TOP OF SEAT IS PARALLELTO HORIZONTAL CROSS MEMBER OF THE MACHINE. YOU MAY HAVE TO TWIST THE SEAT CLOCKWISE OR ANTI-CLOCKWISE TOALIGN IT.