ha new matrix

Upload: ahmad5335

Post on 02-Jun-2018

239 views

Category:

Documents


0 download

TRANSCRIPT

  • 8/10/2019 Ha New Matrix

    1/79

    This document contains information about the POWER systems, IBM storage, adapters, and AIXlevels currently supported by versions of PowerHA 5.5 through PowerHA 7.1. This is a compilation ofthe official support flashes. It was created by and maintained by Shawn Bodily. Please feel free toemail questions/suggestions/errors to [email protected]

    Historically, newer versions of PowerHA have inherited device support from previous versions, unless

    specific support was removed by the product. Over time this has not been common to removesupport for very old hardware. Technically, if it was supported in the past, and the hardware can run aversion of AIX that is supported by the current version of PowerHA, then it is supported.

    Since PowerHA 7.1 is not supported on any AIX level before 6.1.6, if the hardware is not supportedon 6.1.6, then by definition PowerHA 7.1 would not support it either. Also, if the hardware has notmade any statement of support for AIX 7.1, though the table may show PowerHA supports it, it is notvalid until such support is stated. It is my intention to make it as complete as possible at the time ofwriting; however it only focuses on hardware support from the last five year or so. This consistsmainly of POWER5 and above.

    All POWER5 and above systems are supported on AIX 7.1 and HACMP 5.4.1 and above. Thespecific HACMP/PowerHA requirements forAIX 7.1support and are listed below:

    PowerHA 5.5 SP7

    PowerHA 6.1 SP3

    PowerHA 7.1

    Full software support details are always in the official support flash. The support flashes are usuallyavailable for five years and are embedded in the documented at the end.

    POWER Systems

    POWER5

    p Models PowerHA 5.5 PowerHA 6.1 PowerHA 7.1.1 PowerHA 7.1.2 PowerHA 7

    7037-A50 AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    9110-510 AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    9110-51A AIX 5.3 TL9

    AIX 6.1 TL2 SP3

    AIX 5.3 TL9

    AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2

    AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1

    AIX 7.1 TL2 SP1

    AIX 6.1 TL9 S

    AIX 7.1 TL3 S

    9111-285 AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    9111-520 AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    9113-550 AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    9115-505 AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

  • 8/10/2019 Ha New Matrix

    2/79

    9116-561+ AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    9117-570 AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    9118-575 AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    9119-590 AIX 5.3 TL9AIX 6.1 TL2 SP3 AIX 5.3 TL9AIX 6.1 TL2 SP3 AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2 AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1 AIX 6.1 TL9 SAIX 7.1 TL3 S

    9119-595 AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    9131-52A AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    9133-55A AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    i Models PowerHA 5.5 PowerHA 6.1 PowerHA 7.1.1 PowerHA 7.1.2 PowerHA 7

    9406-520 AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    9406-550 AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    9406-570 AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    9406-590 AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    9406-595 AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

  • 8/10/2019 Ha New Matrix

    3/79

    POWER6

    p Models PowerHA 5.5 PowerHA 6.1 PowerHA 7.1.1 PowerHA 7.1.2 PowerHA 7

    8203-E4A/520 AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    8203-E8A/550 AIX 5.3 TL9

    AIX 6.1 TL2 SP3

    AIX 5.3 TL9

    AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2

    AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1

    AIX 7.1 TL2 SP1

    AIX 6.1 TL9 S

    AIX 7.1 TL3 S

    8204-E8A/550 AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    8234-EMA/560 AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    9117-MMA AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    9119-FHA/595 AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    9125-F2A/575 AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    Note:Built-in serial ports in POWER6 servers are not available forPowerHA use. It is suggested to use disk heartbeating instead. Howeverthe built-in ethernet (IVE) adapters are supported for PowerHA use.

  • 8/10/2019 Ha New Matrix

    4/79

    POWER7

    p Models PowerHA 5.5 PowerHA 6.1 PowerHA 7.1.1 PowerHA 7.1.2 PowerHA 7

    8202-E4B/720 AIX 5.3 TL12AIX 6.1 TL5

    AIX 5.3 TL12AIX 6.1 TL5AIX 7.1,

    HA SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    8202-E4C/720 AIX 5.3 TL12RSCT 2.4.13.0

    AIX 6.1 TL5RSCT 2.5.5.2

    AIX 7.1 HA TL11RSCT 3.1.0.3

    AIX 5.3 TL12RSCT 2.4.13.0

    AIX 6.1 TL5RSCT 2.5.5.2

    AIX 7.1,HA SP3RSCT 3.1.0.3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    8202-E4D/720 N/A HA V6.1 TL 6AIX V6.1 TL 8 orAIX 7.1 TL2

    N/A AIX V6.1 TL 8 orAIX 7.1 TL2

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    8205-E6B/740 AIX 5.3 TL12AIX 6.1 TL5

    AIX 5.3 TL12AIX 6.1 TL5AIX 7.1, HA SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    8205-E6C/740 AIX 5.3 TL12RSCT 2.4.13.0

    AIX 6.1 TL5RSCT 2.5.5.2

    AIX 7.1 HA TL11RSCT 3.1.0.3

    AIX 5.3 TL12RSCT 2.4.13.0

    AIX 6.1 TL5RSCT 2.5.5.2

    AIX 7.1,HA SP3RSCT 3.1.0.3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    8205-E6D/740 N/A HA V6.1 TL 6AIX V6.1 TL 8 orAIX 7.1 TL2

    N/A AIX V6.1 TL 8 orAIX 7.1 TL2

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    8231-E1C/710AIX 5.3 TL12RSCT 2.4.13.0

    AIX 6.1 TL5RSCT 2.5.5.2

    AIX 7.1 HA TL11RSCT 3.1.0.3

    AIX 5.3 TL12RSCT 2.4.13.0

    AIX 6.1 TL5RSCT 2.5.5.2

    AIX 7.1,HA SP3RSCT 3.1.0.3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    8231-E1D/710 N/A HA V6.1 TL 6AIX V6.1 TL 8 orAIX 7.1 TL2

    N/A AIX V6.1 TL 8 orAIX 7.1 TL2

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    8231-E2B/710 AIX 5.3 TL12AIX 6.1 TL5

    AIX 5.3 TL12AIX 6.1 TL5AIX 7.1,

    HA SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    8231-E2B/730 AIX 5.3 TL12AIX 6.1 TL5

    AIX 5.3 TL12AIX 6.1 TL5AIX 7.1,HA SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    8231-E1C/730 AIX 5.3 TL12RSCT 2.4.13.0

    AIX 6.1 TL5RSCT 2.5.5.2

    AIX 7.1 HA TL11

    AIX 5.3 TL12RSCT 2.4.13.0

    AIX 6.1 TL5RSCT 2.5.5.2

    AIX 7.1,

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

  • 8/10/2019 Ha New Matrix

    5/79

    RSCT 3.1.0.3 HA SP3RSCT 3.1.0.3

    8231-E2D/730 N/A HA V6.1 TL 6AIX V6.1 TL 8 orAIX 7.1 TL2

    N/A AIX V6.1 TL 8 orAIX 7.1 TL2

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    8233-E8B/750 AIX 5.3 TL11 SP1AIX 6.1 TL4 SP3

    AIX 5.3 TL11AIX 6.1 TL4 SP3

    AIX 7.1 SP2,HA SP3,RSCT 3.1.0.3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    8408-E8D/750 N/A AIX 6.1 TL8AIX 7.1 TL2HA TL6

    N/A AIX 6.1 TL8AIX 7.1 TL2HA TL6

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    9109-RMD/760 N/A HA V6.1 TL 6AIX V6.1 TL 8 orAIX 7.1 TL2

    N/A AIX V6.1 TL 8 orAIX 7.1 TL2

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    9117-MMB/770 AIX 5.3 TL11AIX 6.1 TL4 SP3

    AIX 5.3 TL11AIX 6.1 TL4 SP3AIX 7.1,

    HA SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    9117-MMC/770 AIX 5.3 TL12RSCT 2.4.13.0

    AIX 6.1 TL5RSCT 2.5.5.2

    AIX 7.1 HA TL11RSCT 3.1.0.3

    AIX 5.3 TL12RSCT 2.4.13.0

    AIX 6.1 TL5RSCT 2.5.5.2

    AIX 7.1,HA SP3RSCT 3.1.0.3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    9117-MMD/770 N/A AIX 6.1 TL6 SP10AIX 7.1 TL2HA TL6

    N/A AIX 6.1 TL8AIX 7.1 TL2HA TL6

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    9119-FHB/795 AIX 5.3 TL12

    AIX 6.1 TL5

    AIX 5.3 TL12

    AIX 6.1 TL5AIX 7.1,HA SP3

    AIX 6.1 TL7 SP2

    AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1

    AIX 7.1 TL2 SP1

    AIX 6.1 TL9 S

    AIX 7.1 TL3 S

    9125-F2C/775 AIX 5.3 TL12RSCT 2.4.13.0

    AIX 6.1 TL5RSCT 2.5.5.2

    AIX 7.1 HA TL11RSCT 3.1.0.3

    AIX 5.3 TL12RSCT 2.4.13.0

    AIX 6.1 TL5RSCT 2.5.5.2

    AIX 7.1,HA SP3RSCT 3.1.0.3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    9179-FHB/780 AIX 5.3 TL11AIX 6.1 TL4 SP3

    AIX 5.3 TL11 orAIX 6.1 TL4 SP3

    AIX 7.1,HA SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    9179-FHC/780 AIX 5.3 TL12RSCT 2.4.13.0

    AIX 6.1 TL5RSCT 2.5.5.2

    AIX 7.1 HA TL11RSCT 3.1.0.3

    AIX 5.3 TL12RSCT 2.4.13.0

    AIX 6.1 TL5RSCT 2.5.5.2

    AIX 7.1,HA SP3RSCT 3.1.0.3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    9179-MHDx/780 N/A AIX 6.1 TL6 SP10 N/A AIX 6.1 TL8 SP1 AIX 6.1 TL9 S

  • 8/10/2019 Ha New Matrix

    6/79

  • 8/10/2019 Ha New Matrix

    7/79

  • 8/10/2019 Ha New Matrix

    8/79

    Blades

    p Models PowerHA 5.5 PowerHA 6.1 PowerHA 7.1.1 PowerHA 7.1.2 PowerHA 7.1.3

    2458-002 AIX 5.3 TL12RSCT 2.4.13.0

    AIX 6.1 TL05

    RSCT 3.1.0.4

    AIX 5.3 TL12RSCT 2.4.13.0

    AIX 6.1 TL05

    RSCT 3.1.0.4AIX 7.1 HA SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    7778-23X/JS23

    AIX 5.3 TL9AIX 6.1 TL2 SP1

    AIX 5.3 TL9AIX 6.1 TL2 SP1

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    7778-43X/JS43

    AIX 5.3 TL9AIX 6.1 TL2 SP1

    AIX 5.3 TL9AIX 6.1 TL2 SP1

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    7891-73Y/PS703

    AIX 5.3 TL12AIX 6.1 TL5AIX 7.1PowerHA SP8

    AIX 5.3 TL12AIX 6.1 TL5AIX 7.1PowerHA SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    7998-60X/JS12

    AIX 5.3 TL9AIX 6.1 TL2 SP1 AIX 5.3 TL9AIX 6.1 TL2 SP1 AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2 AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1 AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    7998-61X/JS22

    AIX 5.3 TL7AIX 6.1 TL2 SP1

    AIX 5.3 TL9AIX 6.1 TL2 SP1

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    8406-70Y/PS700

    AIX 5.3 TL12AIX 6.1 TL5

    AIX 5.3 TL12AIX 6.1 TL5

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    8406-71Y/PS701PS702

    AIX 5.3 TL12AIX 6.1 TL5

    AIX 5.3 TL12AIX 6.1 TL5

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    8406-

    74Y/PS704

    AIX 5.3 TL12

    AIX 6.1 TL5AIX 7.1HA SP8

    AIX 5.3 TL12

    AIX 6.1 TL5AIX 7.1HA SP3

    AIX 6.1 TL7 SP2

    AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1

    AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1

    AIX 7.1 TL3 SP1

    8844-31U/JS218844-51U/JS21

    AIX 5.3 TL9AIX 6.1 TL2 SP1

    AIX 5.3 TL9AIX 6.1 TL2 SP1

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    IBM zEnterprise BladeCenter Extension (zBX)

    Blade support does include support for both IVM and IVE on both POWER6 and POWER7 blades.The following cards are supported in the P6 and P7 blades:

    1641 10Gb Ethernet Pass-Thru Module8240 Emulex 8Gb FC Expansion Card (CIOv)8241 QLogic 4Gb FC Expansion Card (CIOv)8242 QLogic 8Gb Fibre Channel Expansion Card (CIOv)

  • 8/10/2019 Ha New Matrix

    9/79

    8243 Broadcom 2-port Gb Ethernet Expansion Card (CIOv)8246 SAS Connectivity Card (CIOv)8251 Emulex 4Gb FC Expansion Card (CFFv)8252 QLogic combo Ethernet and 4 Gb Fibre Channel Expansion Card (CFFh)8271 QLogic Ethernet/8Gb FC Expansion Card (CFFh)8291 Broadcom 4-port 1 Gigabit Ethernet Expansion Card (CFFh/PCI-E)

  • 8/10/2019 Ha New Matrix

    10/79

    Flex Systems

    p Models PowerHA 5.5 PowerHA 6.1 PowerHA 7.1.1 PowerHA 7.1.2 PowerHA 7

    7895-22x/p260 NA AIX 6.1 TL07 SP3

    AIX APAR IV14283RSCT 3.1.0.3PowerHA SP3

    AIX 7.1 TL01 SP03AIX APAR IV14284

    AIX 6.1 TL07 SP3

    AIX APAR IV14283RSCT 3.1.0.3

    AIX 7.1 TL01 SP03AIX APAR IV14284

    AIX 6.1 TL8 SP1

    AIX 7.1 TL2 SP1

    AIX 6.1 TL9 S

    AIX 7.1 TL3 S

    7895-23x/p260 NA PowerHA V6.1 SP3,AIX 6.1 TL 8 SP 3

    NA PowerHA V7.1.2SP2,

    AIX 6.1 TL 8 SP 3

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    7895-42x/p460 NA AIX 6.1 TL07 SP3AIX APAR IV14283RSCT 3.1.0.3PowerHA SP3

    AIX 7.1 TL01 SP03AIX APAR IV14284

    AIX 6.1 TL07 SP3AIX APAR IV14283RSCT 3.1.0.3

    AIX 7.1 TL01 SP03AIX APAR IV14284

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    7895-43x/p460 NA PowerHA V6.1 SP3,AIX 6.1 TL 8 SP 3

    NA PowerHA V7.1.2SP2,

    AIX 6.1 TL 8 SP 3

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    The following cards are supported in the PureFlex nodes:

    EC23 IBM Flex System FC5052 2-port 16Gb FC AdapterEC24 IBM Flex System CN4058 8-port 10Gb ConvergedEC2E IBM Flex System FC5054 4-port 16Gb FC Adapter

    IBM Storage

    It is common to use multipathing drivers with storage. If utilizing MPIO, SDD, and/or SDDPCM on anyPowerHA controlled storage, it is a requirement to use enhanced concurrent volume groups (ECVGs)This requirement also applies to vSCSIand NPIVdevices.

    Fiber Channel

    DS Units

    Model PowerHA 5.5 PowerHA 6.1 PowerHA 7.1.1 PowerHA 7.1.2 PowerHA 7

    DS3400 AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    DS3500 AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    DS4100 AIX 5.3 TL7AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

  • 8/10/2019 Ha New Matrix

    11/79

    DS4200 AIX 5.3 TL7AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    DS4300 AIX 5.3 TL7AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    DS4400 AIX 5.3 TL7AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    DS4500 AIX 5.3 TL7AIX 6.1 TL2 SP3 AIX 5.3 TL9AIX 6.1 TL2 SP3 AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2 AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1 AIX 6.1 TL9 SAIX 7.1 TL3 S

    DS4700 AIX 5.3 TL9AIX TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    DS4800 AIX 5.3 TL7AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    DS5020 AIX 5.3 TL9AIX 6.1 TL2 SP1

    AIX 5.3 TL9AIX 6.1 TL2 SP1

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    DS6000DS6800 522

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    DS5100

    SSDs

    AIX 5.3 TL9

    AIX 6.1 TL2 SP1

    AIX 5.3 TL9

    AIX 6.1 TL2 SP1

    AIX 6.1 TL7 SP2

    AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1

    AIX 7.1 TL2 SP1

    AIX 6.1 TL9 S

    AIX 7.1 TL3 S

    DS5300

    SSDs

    AIX 5.3 TL9AIX 6.1 TL2 SP1

    AIX 5.3 TL9AIX 6.1 TL2 SP1

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    DS8000931,932,9B2

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    DS8700 AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    DS8800 HA SP11

    AIX 6.1 TL5RSCT 2.5.5.2AIX 7.1RSCT 3.1.0.3

    HA SP3

    AIX 6.1 TL5RSCT 2.5.5.2AIX 7.1RSCT3.1.0.3

    AIX 6.1 TL7 SP2

    AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1

    AIX 7.1 TL2 SP1

    AIX 6.1 TL9 S

    AIX 7.1 TL3 S

    DS5100 and DS5300 Notes:

    These storage units support MPIO only.

    Testing was performed with DS5100/5300 Microcode levels 7.30.21 and 7.36.08

    This support includes using SDDPCM, with the caveat that SDDPCM support requires the use ofenhanced concurrent volume groups.

    DS4700 and DS4800 Notes:

  • 8/10/2019 Ha New Matrix

    12/79

    This support announcement is for the addition of MPIO support. These units have been supportedsince 2005 using RDAC.

    Testing was performed with DS4700/4800 Microcode levels 7.10.23 and 7.15.07

    This support includes using SDDPCM, with the caveat that SDDPCM support requires the use of

    enhanced concurrent volume groups.

    Using MPIO with PowerHA always requires the use of enhanced concurrent vgs. Also, in general,support for DS units require switch attachment. Otherwise if direct attaching, ONLY cluster nodesmust be connected to them, AND the use of ECVGs is required.

    XIV

    Model PowerHA 5.5 PowerHA 6.1 PowerHA 7.1.1 PowerHA 7.1.2 PowerHA 7

    XIV 2810-A14 AIX 5.3 TL9AIX TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    XIV 2812-114 HA SP7AIX 6.1 TL5 SP1RSCT 2.5.5.2

    AIX 7.1RSCT 3.1.0.3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    San Volume Controller (SVC)

    Model PowerHA 5.5 PowerHA 6.1 PowerHA 7.1.1 PowerHA 7.1.2 PowerHA 7

    2145-4F2 PowerHA SP6AIX 5.3 TL9

    AIX 6.1 TL2 SP3

    PowerHA SP1AIX 5.3 TL9

    AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    2145-8F2 PowerHA SP8AIX 5.3 TL9AIX 6.1 TL2 SP3

    PowerHA SP1AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SAIX 7.1 TL3 S

    SVC Software levels supported up through SVC v7.2. The levels shown in the table above are thebare minimum requirements for v5.1. Other individual supported SVC levels are listed below,

    SVC v6.4.1

    SVC v6.4SVC v6.3SVC v6.2SVC v6.1SVC v5.1SVC 4.3 & 4.3 1SVC 4.2SVC 4.1

  • 8/10/2019 Ha New Matrix

    13/79

  • 8/10/2019 Ha New Matrix

    14/79

    RSCT 2.4.13.0AIX 6.1 TL5RSCT 2.5.5.2

    AIX 7.1HA TL11RSCT 3.1.0.3

    RSCT 2.4.13.0AIX 6.1 TL5RSCT 2.5.5.2

    AIX 7.1HA SP3RSCT 3.1.0.3

    AIX 7.1 TL1 SP2 AIX 7.1 TL2 SP1 AIX 7.1 TL3 S

    SSD

    Model PowerHA 6.1 PowerHA 7.1.1 PowerHA 7.1.2 PowerHA 7.1.3

    5888-EXP30 AIX 6.1 TL8AIX 7.1 TL2HA TL6

    N/A AIX 6.1 TL8AIX 7.1 TL2HA TL6

    AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    EDR1-EXP30 AIX 6.1 TL8AIX 7.1 TL2HA TL6

    N/A AIX 6.1 TL8AIX 7.1 TL2HA TL6

    AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    SCSI

    Model PowerHA 5.5 PowerHA 6.1 PowerHA 7.1.1 PowerHA 7.1.2 PowerHA 7.1.3

    7031-D24 AIX 5.3 TL7AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    NAS

    Model PowerHA 5.5 PowerHA 6.1 PowerHA 7.1.1 PowerHA 7.1.2 PowerHA 7.1.3

    N3300 2859-A20N3400 2859-

    A21N3600 2862-

    A20

    HA 5.5 SP7AIX 5.3 TL12RSCT 2.4.13.0

    AIX 6.1 TL05RSCT 2.5.5.0

    AIX 7.1RSCT 3.1.0.3

    HA 6.1 SP3AIX 5.3 TL12RSCT 2.4.13.0

    AIX 6.1 TL05RSCT 2.5.5.0

    AIX 7.1RSCT 3.1.0.3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    N3700 (A20) AIX 5.3 TL7AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    N5200 (A20) AIX 5.3 TL7AIX 6.1 TL2 SP3 AIX 5.3 TL9AIX 6.1 TL2 SP3 AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2 AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1 AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    N5200 (G20) AIX 5.3 TL7AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    N5300 AIX 5.3 TL7AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    N5500 (A20) AIX 5.3 TL7AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2

    AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    N5500 (G20) AIX 5.3 TL7 AIX 5.3 TL9 AIX 6.1 TL7 SP2 AIX 6.1 TL8 SP1 AIX 6.1 TL9 SP1

  • 8/10/2019 Ha New Matrix

    15/79

    AIX 6.1 TL2 SP3 AIX 6.1 TL2 SP3 AIX 7.1 TL1 SP2 AIX 7.1 TL2 SP1 AIX 7.1 TL3 SP1

    N5600 AIX 5.3 TL7AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    N6040 AIX 5.3 TL7AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    N6060 AIX 5.3 TL7

    AIX 6.1 TL2 SP3

    AIX 5.3 TL9

    AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2

    AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1

    AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1

    AIX 7.1 TL3 SP1N6070 AIX 5.3 TL7

    AIX 6.1 TL2 SP3AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    N6210N6240N6270

    HA 5.5 SP7AIX 5.3 TL12RSCT 2.4.13.0

    AIX 6.1 TL05RSCT 2.5.5.0

    AIX 7.1RSCT 3.1.0.3

    HA 6.1 SP3AIX 5.3 TL12RSCT 2.4.13.0

    AIX 6.1 TL05RSCT 2.5.5.0

    AIX 7.1RSCT 3.1.0.3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    N7600 (A20) AIX 5.3 TL7AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    N7600 (G20) AIX 5.3 TL7AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    N7700 (A21) AIX 5.3 TL7AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    N7700 (G21) AIX 5.3 TL7AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    N7800 (A20) AIX 5.3 TL7AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    N7800 (G20) AIX 5.3 TL7AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    N7900 (A21) AIX 5.3 TL7

    AIX 6.1 TL2 SP3

    AIX 5.3 TL9

    AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2

    AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1

    AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1

    AIX 7.1 TL3 SP1N7900 (G21) AIX 5.3 TL7

    AIX 6.1 TL2 SP3AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

    Adapters

    Fiber Channel

    #1768 Dual 10 Gb Copper + Dual 1 Gb Ethernet#1905 4 Gb Single Port Fibre Channel PCI-X 2.0 DDR Adapter#1910 4 Gb Dual Port Fibre Channel PCI-X 2.0 DDR Adapter#1957 2 Gigabit Fibre Channel PCI-X Adapter#1977 2 Gigabit Fibre Channel PCI-X Adapter#5273 LP 8 Gb PCI-Express Dual Port Fibre Channel Adapter*#5716 2 Gigabit Fibre Channel PCI-X Adapter#5276 LP 4 Gb PCI Express Fibre Channel Adapter

  • 8/10/2019 Ha New Matrix

    16/79

    #5729 LP 4 Gb PCI-E2 8Gb 4-port Fibre Channel Adapter#5735 8 Gb PCI-Express Dual Port Fibre Channel Adapter*#5758 4 Gb Single Port Fibre Channel PCI-X 2.0 DDR Adapter

    #5759 4 Gb Dual Port Fibre Channel PCI-X 2.0 DDR Adapter

    #5773 4 Gb PCI Express Fibre Channel Adapter#5774 4 Gb PCI Express Fibre Channel Adapter

    #6228 1-and 2-Gigabit Fibre Channel Adapter for 64-bit PCI Bus#6239 2 Gigabit FC PCI-X Adapter

    #EC23 IBM Flex System FC5054 4-port 16Gb FC Adapter#EC2E IBM Flex System FC5054 4-port 16Gb FC Adapter#EN0A PCIe2 16 Gb 2-port Fibre Channel#EN0B PCIe2 16 Gb 2-port Fibre Channel

    *5273/5735 bare minimum requirements are PowerHA 5.4.1 SP2 or 5.5 SP1.

    FCoE/CNA

    #5437 Brocade 2-port 10GbE Converged Network Adapter for IBM Blades #5708 10Gb FCoE PCIe Dual Port Adapter#EC24 IBM Flex System CN4058 8-port 10Gb Converged Adapter#EN0H PCIe2 LP 2x10Gb FCoE 2x1GbE SFP+ Adapter#EN0J PCIe2 LP 2x10Gb FCoE 2x1GbE SFP+ Adapter

    SAS

    #5278 LP 2x4port PCI-Express SAS Adapter 3Gb#5805 PCI-Express 380MB Cache Dual x4 3GB SAS RAID Adapter#5901 PCI-Express SAS Adapter

    #5902 PCI-X DDR Dual x4 Port SAS RAID Adapter#5903 PCI-Express SAS Adapters#5912 PCI-X DDR External Dual x4 Port SAS Adapter

    SAS software support requirements are shown in the following table.

    PowerHA 5.5 PowerHA 6.1 PowerHA 7.1.1 PowerHA 7.1.2 PowerHA 7.1.3

    PowerHA SP2AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 5.3 TL9AIX 6.1 TL2 SP3

    AIX 6.1 TL7 SP2AIX 7.1 TL1 SP2

    AIX 6.1 TL8 SP1AIX 7.1 TL2 SP1

    AIX 6.1 TL9 SP1AIX 7.1 TL3 SP1

  • 8/10/2019 Ha New Matrix

    17/79

    Ethernet

    #1768 Dual 10 Gb Copper + Dual 1 Gb Ethernet#1769 Dual 10 Gb Optical + Dual 1 Gb Ethernet

    #1954 4-Port 10/100/100 Base-TX PCI-X Adapter#1959 IBM 10/100/1000 Base-TX Ethernet PCI-X Adapter#1978 IBM Gigabit Ethernet-SX PCI-X Adapter#1979 IBM 10/100/1000 Base-TX Ethernet PCI-X Adapter#1981 IBM 10 Gigabit Ethernet-SR PCI-X Adapter#1982 IBM 10 Gigabit Ethernet-LR PCI-X Adapter#1983 IBM 2-port 10/100/1000 Base-TX Ethernet PCI-X#1984 IBM Dual Port Gigabit Ethernet-SX PCI-X Adapter#1990 IBM 2-port 10/100/1000 Base-TX Ethernet PCI-X#4961 IBM Universal 4-Port 10/100 Ethernet Adapter#4962 IBM 10/100 Mbps Ethernet PCI Adapter II

    #5260 PCIe2 LP 4-port 1GbE Adapter#5271 LP 4-Port Ethernet 10/100/1000 Base-TX PCI-X Adapter#5274 LP 2-Port Gigabit Ethernet-SX PCI Express#5284 PCIe2 2-port LP 10GbE SR Adapter#5286 PCIe2 2-port LP 10GbE SFP+ Copper Adapter#5288 PCIe2 2-port 10GbE SFP+ Copper Adapter#5287 PCIe2 2-port 10GbE SR Adapter#5700 IBM Gigabit Ethernet-SX PCI-X Adapter#5701 IBM 10/100/1000 Base-TX Ethernet PCI-X Adapter#5706 IBM 2-Port 10/100/1000 Base-TX Ethernet PCI-X Adapter#5707 IBM 2-Port Gigabit Ethernet-SX PCI-X Adapter#5717 IBM 4-Port Ethernet 10/100/1000 Base-TX PCI-X Adapter#5718 IBM 10 Gigabit -SR/-LR Ethernet PCI-x adapters#5719 IBM 10 Gigabit -SR/-LR Ethernet PCI-x adapters#5721 IBM 10 Gigabit Ethernet-SR PCI-X 2.0 Adapter#5722 IBM 10 Gigabit Ethernet-LR PCI-X 2.0 Adapter#5740 4-Port 10/100/100 Base-TX PCI-X Adapter#5767 Adapter 2-Port 10/100/1000 Base-TX Ethernet PCI Express#5768 Adapter 2-Port Gigabit Ethernet-SX PCI Express#5769 10Gb Ethernet-SR PCI Express Adapter#5772 10Gb Ethernet-LR PCI Express Adapter#5899: PCIe2 4-port 1GbE Adapter

    Infiniband

    #1809 IBM GX Dual-port 4x IB HCA#1810 IBM GX Dual-port 4x IB HCA#1811 IBM GX Dual-port 4x IB HCA#1812 IBM GX Dual-port 4x IB HCA#1820 IBM GX Dual-port 12x IB HCA

  • 8/10/2019 Ha New Matrix

    18/79

    SCSI and iSCSI

    #1912 IBM PCI-X DDR Dual Channel Ultra320 LVD SCSI Adapter#1913 PCI-X DDR Dual Channel Ultra320 SCSI RAID Adapter#1975 PCI-X Dual Channel Ultra320 SCSI RAID Adapter#1986 1 Gigabit-TX iSCSI TOE PCI-X adapter (copper connector)

    #1987 1 Gigabit-SX iSCSI TOE PCI-X adapter (optical connector)#5703 PCI-X Dual Channel Ultra320 SCSI RAID Adapter#5710 PCI-X Dual Channel Ultra320 SCSI Adapter#5711 PCI-X Dual Channel Ultra320 SCSI RAID Blind Swap Adapter#5712 PCI-X Dual Channel Ultra320 SCSI Adapter#5713 1 Gigabit-TX iSCSI TOE PCI-X adapter (copper connector)#5714 1 Gigabit-SX iSCSI TOE PCI-X adapter (optical connector)#5736 IBM PCI-X DDR Dual Channel Ultra320 SCSI Adapter#5737 PCI-X DDR Dual Channel Ultra320 SCSI RAID Adapter

    RS232

    PowerHA 7.1 no longer supports RS-232, so the following adapters are supported up throughPowerHA 6.1 only.

    #2943 8-Port Asynchronous EIA-232/RS-422, PCI bus Adapter#2944 128-Port Asynchronous Controller, PCI bus#5277 IBM LP 4-Port Async EIA-232 PCIe Adapter#5723 2-Port Asynchronous EIA-232/RS-422, PCI bus Adapter#5785 IBM 4-Port Async EIA-232 PCIe Adapter*

    *The 5277/5785 adapter above is only supported by PowerHA 5.5 and 6.1.

  • 8/10/2019 Ha New Matrix

    19/79

    IBM PowerHA SystemMirror for AIX Adds Support for the IBM Power 8 Family of Servers

    June 10, 2014

    IBM PowerHA SystemMirror for AIX* adds support for the new IBM Power 8 family of servers.

    Please refer to the following information for support details:

    1. This support announcement is for PowerHA SystemMirror version v6.1 and v7 products.Recommended levels are: PowerHA v6.1 SP12 and PowerHA v7.1.3 SP1.

    2. Note that these PowerHA SystemMirror products can be used with AIX v6 or v7 OperatingSystems on Power 8 System.

    3. For requirements regarding the level of AIX needed for Power 8 support, refer to AIX relatedsupport publications

    4. This support is based on the requirement that deployment meets the generic clustering

    requirements.

    Examples of which are:

    Ensure that redundant network communication links between the cluster nodes is availableand operating correctly

    If multicast based v7 cluster is deployed, mping based multicast packet communication checkshould pass for more than 5 minutes (some routers block multicast traffic after 3 minutes or so)

    Shared storage is configured as necessary based on the needs and is operating correctly.Note that repository disk in v7 product is minimally required and be shared across all the

    nodes in the cluster

    Clients are advised to obtain the latest service updates for this support.

    References:1. AIX needs to be updated to correct levels to be deployed on Power 8 systems. More informationabout the same can be found at: http://www-304.ibm.com/support/docview.wss?uid=ssm1maps 2. IBM Service can be obtained from the IBM Electronic Fix Distribution site at:http://www.ibm.com/support/fixcentral/

    For questions or concerns, please send a note to HA Feedback at:

    HA Solutions Feedback/Poughkeepsie/IBM or [email protected]

    * Trademark or registered trademark of International Business Machines Corporation.Other company, product, and service names may be trademarks or service marks of others.

  • 8/10/2019 Ha New Matrix

    20/79

    IBM PowerHA SystemMirror for AIX Supports for IBM System Storage SVC SoftwareV7.1 and 7.2

    February 28, 2014

    IBM PowerHA SystemMirror for AIX*, V6.1 and V7.1 adds support for the IBM System Storage SAN Volume Controller(SVC) Software V7.1 & V7.2. This includes the High Availability and Disaster Recovery (HA/DR) capabilities of IBMPowerHA SystemMirror for AIX V6.1, V7.1.2 and v7.1.3 Enterprise Edition.

    This support includes SVC V7.1 orV7.2 software running on the IBM Storwize family of storage controllers.

    SVC V7.1/v7.2 was tested and qualifiedwith the following AIX/PowerHA levels:.

    AIX V6.1 AIX V7.1

    PowerHA V6.1Enterprise Edition

    PowerHA V6.1 SP6AIX V6.1 TL 8

    PowerHA V6.1 SP6AIX V7.1 TL 2

    PowerHA V7.1Enterprise Edition

    PowerHA V7.1.2AIX 6.1 TL 8

    PowerHA V7.1.2AIX V7.1 TL 2

    Restrictions:

    The support in this Flash does not cover the 'Change Volumes' facility of SVC Global Mirror.

    This support does not include SVC Native IP Replication.

    Notes:This support includes FC-attach, VIOS/vSCSI, and VIOS/NPIV

  • 8/10/2019 Ha New Matrix

    21/79

    IBM PowerHA SystemMirror for AIX: Adapter Support Updates

    September 30, 2013 (Updated 7/24/2014)

    IBM PowerHA SystemMirror for AIX has added support for the following adapters. Unless otherwise noted, this supportincludes vSCSI/NPIV through an underlying VIOS where applicable (F/C adapters).

    Please refer to the following information for support details.

    Power Adapters

    FeatureCode

    Description Min. AIX Level Support Date SANComSupport

    EN0H,EN0J

    (1)

    PCIe2 LP 2x10Gb FCoE2x1GbE SFP+ Adapter

    6.1 TL 7 SP 96.1 TL 8 SP 47.1 TL 1 SP 97.1 TL 2 SP 4

    9/30/2013 No

    EN10, EN11(1) PCIe2 2-port (2 10GbE)Integrated FCoE + NICCNA Adapter

    6.1 TL 7 SP 96.1 TL 8 SP 47.1 TL 1 SP 97.1 TL 2 SP 4

    9/30/2013 No

    EN0A, EN0B PCIe2 16 Gb 2-port FibreChannel Adapter

    6.1 TL 7 SP 96.1 TL 8 SP 47.1 TL 1 SP 97.1 TL 2 SP 4

    9/30/2013 No

    5284/5287 PCIe2 2-port 10GbE SRAdapter

    6.1 TL 7 SP 96.1 TL 8 SP 47.1 TL 1 SP 97.1 TL 2 SP 4

    07/23/2014 No

    5286/5288 PCIe2 2-port 10GbESFP+ Adapter

    6.1 TL 7 SP 96.1 TL 8 SP 47.1 TL 1 SP 97.1 TL 2 SP 4

    02/07/2014 No

    5899/5260 PCIe2 4-port 1 GbEAdapter

    6.1 TL 7 SP 96.1 TL 8 SP 47.1 TL 1 SP 97.1 TL 2 SP 4

    02/07/2014 No

    1768 Dual 10 Gb Copper +Dual 1 Gb Ethernet

    6.1 TL 7 SP 96.1 TL 8 SP 47.1 TL 1 SP 97.1 TL 2 SP 4

    02/07/2014 No

    1769 Dual 10 Gb Optical anddual 1 Gb Ethernet

    6.1 TL 7 SP 96.1 TL 8 SP 47.1 TL 1 SP 97.1 TL 2 SP 4

    02/07/2014 No

    PureFlex Adapters

    FeatureCode

    Description Min. AIX Level Support Date SANComSupport

  • 8/10/2019 Ha New Matrix

    22/79

    EC24 IBM Flex System CN40588-port 10Gb Converged

    Adapter

    6.1 TL 8 SP 47.1 TL 2 SP 4

    9/30/2013 No

    EC23 IBM Flex System FC50544-port 16Gb FC Adapter

    6.1 TL 8 SP 47.1 TL 2 SP 4

    9/30/2013 No

    EC2E IBM Flex System FC50544-port 16Gb FC Adapter

    6.1 TL 8 SP 47.1 TL 2 SP 4

    9/30/2013 No

    Notes:

    1. This support requires the following AIX APAR (please contact support for the appropriate fix):

    AIX Level APAR

    6.1 TL 7 SP 9 IV49291

    6.1 TL 8 SP 4 IV49271

    7.1 TL 1 SP 9 IV49472

    7.1 TL 2 SP 4 IV49023

    Clients are advised to obtain the latest service updates for this support.

  • 8/10/2019 Ha New Matrix

    23/79

    IBM PowerHA SystemMirror for AIX Supports for IBM System Storage SVC Software V6.4.1May 10, 2013

    IBM PowerHA SystemMirror for AIX*, V6.1 and V7.1 adds support for the IBM System Storage SANVolume Controller (SVC) Software V6.4.1. This includes the High Availability and Disaster Recovery(HA/DR) capabilities of IBM PowerHA SystemMirror for AIX V6.1 and V7.1.2 Enterprise Edition.

    This support includes SVC V6.4.1 software running on the IBM Storwize v7000.

    Please refer to the following information for support details.

    IBM System Storage SVCV6.4.1

    AIX V6.1 AIX V7.1

    PowerHA V6.1Enterprise Edition

    PowerHA V6.1 SP3PowerHA V6.1 APAR IV39049PowerHA V6.1 APAR IV33779

    AIX V6.1 TL06 SP03

    PowerHA V6.1 SP3PowerHA V6.1 APAR IV39049PowerHA V6.1 APAR IV33779

    AIX V7.1 TL0 SP02

    PowerHA V7.1Enterprise Edition

    PowerHA V7.1.2 SP2PowerHA V7.1 APAR IV41377PowerHA V7.1 APAR IV33782

    AIX V6.1 TL08 SP01

    PowerHA V7.1.2 SP2PowerHA V7.1 APAR IV41377PowerHA V7.1 APAR IV33782

    AIX V7.1 TL02 SP01

    Restrictions:

    The support in this Flash does not cover the 'Change Volumes' facility of SVC Global Mirror.PowerHA SystemMirror does not, at this time, support - and will reject as erroneous -configurations with this facility. IBM intends to remove this restriction in a future release.

  • 8/10/2019 Ha New Matrix

    24/79

    IBM PowerHA SystemMirror for AIX Adds Support for the New IBM Power7+ 760 (9109-RMDx)

    May 02, 2013

    IBM PowerHA SystemMirror for AIX* adds support for the new IBM Power7+ 760 (/9109-RMDx).

    Please refer to the following information for support details.Power 7+ 760 (9109-

    RMDx)AIX V6.1 AIX V7.1

    PowerHA SystemMirrorV6.1

    PowerHA V6.1 TL 6AIX V6.1 TL 8

    PowerHA V6.1 TL 6AIX V7.1 TL 2

    PowerHA SystemMirrorV7.1

    PowerHA V7.1.2AIX 6.1 TL 8

    PowerHA V7.1.2AIX V7.1 TL 2

    Clients are advised to obtain the latest service updates for this support.

    Notes:

    Integrated Virtualization Manager (IVM) is also supported.

  • 8/10/2019 Ha New Matrix

    25/79

    IBM PowerHA SystemMirror for AIX Adds Support for the New IBM Power7+ 720/740 (8202-E4D/8205-E6D)

    May 02, 2013

    IBM PowerHA SystemMirror for AIX* adds support for the new IBM Power7+ 720/740 (8202-

    E4D/8205-E6D).

    Please refer to the following information for support details.

    Power 7+ 720/740 (8202-E4D/8205-E6D)

    AIX V6.1 AIX V7.1

    PowerHA SystemMirrorV6.1

    PowerHA V6.1 TL 6AIX V6.1 TL 8

    PowerHA V6.1 TL 6AIX V7.1 TL 2

    PowerHA SystemMirrorV7.1

    PowerHA V7.1.2AIX 6.1 TL 8

    PowerHA V7.1.2AIX V7.1 TL 2

    Clients are advised to obtain the latest service updates for this support.

    Notes:

    Integrated Virtualization Manager (IVM) is also supported.

  • 8/10/2019 Ha New Matrix

    26/79

    IBM PowerHA SystemMirror for AIX Adds Support for the New IBM Power7+ 710/730 (8231-E1D/E2D)

    May 02, 2013

    IBM PowerHA SystemMirror for AIX* adds support for the new IBM Power7+ 710/730 (8321-

    E1D/E2D).

    Please refer to the following information for support details.

    Power 7+ 710/730 (8321-E1D/E2D)

    AIX V6.1 AIX V7.1

    PowerHA SystemMirrorV6.1

    PowerHA V6.1 TL 6AIX V6.1 TL 8

    PowerHA V6.1 TL 6AIX V7.1 TL 2

    PowerHA SystemMirrorV7.1

    PowerHA V7.1.2AIX 6.1 TL 8

    PowerHA V7.1.2AIX V7.1 TL 2

    Clients are advised to obtain the latest service updates for this support.

  • 8/10/2019 Ha New Matrix

    27/79

  • 8/10/2019 Ha New Matrix

    28/79

    IBM PowerHA SystemMirror for AIX Adds Support for the New IBM Power7+ 750 (8408-E8Dx)

    April 12, 2013

    IBM PowerHA SystemMirror for AIX* adds support for the new IBM Power7+ 750 (8408-E8Dx).

    Please refer to the following information for support details.Power 7+ 750 (8408-

    E8Dx)AIX V6.1 AIX V7.1

    PowerHA SystemMirrorV6.1

    PowerHA V6.1 SP6AIX V6.1 TL 8

    PowerHA V6.1 SP6AIX V7.1 TL 2

    PowerHA SystemMirrorV7.1

    PowerHA V7.1.2AIX 6.1 TL 8

    PowerHA V7.1.2AIX V7.1 TL 2

    Clients are advised to obtain the latest service updates for this support.

    Notes: Integrated Virtualization Manager (IVM) is also supported.

  • 8/10/2019 Ha New Matrix

    29/79

    IBM PowerHA SystemMirror Adds Suppor t for the IBM FlashSystem 710/720 and 810/820March 31, 2013

    IBM PowerHA* SystemMirror for AIX V6.1 adds support for the IBM FlashSystems 710/720 and810/820.

    Please refer to the following information for support details.

    IBM FlashSystem710/720 and 810/820

    AIX V6.1 AIX V7.1

    PowerHA SystemMirrorV6.1

    PowerHA V6.1 SP 6AIX V6.1 TL 8 SP1AIX APAR IV38225

    PowerHA V6.1 SP 6AIX V7.1 TL 2

    AIX APAR IV38226

    PowerHA SystemMirrorV7.1

    PowerHA V7.1.2 SP2AIX 6.1 TL 8

    AIX APAR IV38225

    PowerHA V7.1.2 SP2AIX V7.1 TL 2

    AIX APAR IV38226

    Notes: This support is for Standard Edition only, as the device does not support replication.

  • 8/10/2019 Ha New Matrix

    30/79

    IBM PowerHA SystemMirror for AIX Supports IBM VIO Server V2.2.2 Shared Storage Pool March 31, 2013

    IBM* PowerHA SystemMirror for AIX*, Versions 6.1 and 7.1 extend support to include IBM Virtual I/OServer (VIOS) V2.2.2 Shared Storage Pool virtual SCSI, virtual Ethernet, and NPIV devices on allPowerHA supported IBM POWER6* and POWER7* processor-based servers along with IBM Blades.

    Please refer to the following table for support details.

    AIX Client LPARs Running PowerHA VIOServer

    AIX v6.1 AIX v7.1

    PowerHASystemMirror

    v6.1

    AIX V6.1 TL05, PowerHA V6.1SP3,

    AIX V7.1

    2.2.2

    PowerHASystemMirrorV7.1

    AIX V6.1 TL06 AIX V7.1 2.2.2

    Notes:

    PowerHA XD GLVM is supported with VIO PowerHA 7.1 supports cluster communication between hosts using SAN connections that exist

    between them. More information about the SAN communication can be found in the PowerHA7.1 documentation. With the release of VIOS 2.2.0.11-FP24SP01 SAN communication can be

    established for PowerHA LPARs/nodes even when the storage adapters are virtualizedthrough VIOS. SAN communication is enabled by establishing a VLAN between the VIOSclient and the VIOS (setup instructions are available in AIX documentation). SANcommunication through VIOS can be setup for both NPIV and vSCSI environments.

    PowerHA 7.1 is fully supported with all supported previous levels of IBM VIO Server. However,these levels do not provide support for SANCOM, which requires features only available in VIOServer 2.2.

    All support and restrictions associated with Virtual Ethernet provided by IBM VIO Server V2.2 apply tothe corresponding level of IVE.

  • 8/10/2019 Ha New Matrix

    31/79

    IBM PowerHA SystemMirror for AIX Standard Edition Adds Support for the IBM Flex SystemV7000 Storage Node (4939-A49, 4939-X49, 4939-H49)March 31, 2013

    IBM PowerHA SystemMirror Standard Edition for AIX v6.1 and v7.1 adds support for the IBM FlexSystem V7000 Storage Node (4939-A49, 4939-X49, 4939-H49) running IBM SAN Volume Controller

    (SVC) Software v6.4.1.

    Please refer to the following information for support details.

    IBM Flex SystemV7000 Storage

    Node

    AIX V6.1 AIX V7.1

    PowerHA V6.1 PowerHA V6.1 TL 6AIX V6.1 TL 8

    PowerHA V6.1 TL6

    AIX V7.1 TL 2

    PowerHA V7.1 PowerHA V7.1.2AIX 6.1 TL 8

    PowerHA V7.1.2AIX V7.1 TL 2

  • 8/10/2019 Ha New Matrix

    32/79

    IBM PowerHA SystemMirror Adds Suppor t for the IBM EXP30 Ultra SSD I/O Drawer (F/C5888 an EDR1)March 31, 2013July 29, 2013

    IBM PowerHA* SystemMirror for AIX V6.1 and V7.1 adds support for the IBM EXP30 SSD I/ODrawer (F/C 5888 and F/C EDR1).

    Please refer to the following information for support details.

    IBM EXP Ultra SSD I/ODrawer

    AIX V6.1 AIX V7.1

    PowerHASystemMirror V6.1

    PowerHA V6.1 SP 6AIX V6.1 TL 8

    PowerHA V6.1 SP 6AIX V7.1 TL 2

    PowerHASystemMirror V7.1

    PowerHA V7.1.2 SP2AIX 6.1 TL 8

    PowerHA V7.1.2 SP2AIX V7.1 TL 2

    Notes:

    This support is for Standard Edition only, as the device does not support replication.

  • 8/10/2019 Ha New Matrix

    33/79

    IBM PowerHA SystemMirror for AIX Supports IBM System Storage SVC Software V6.4December 28, 2012

    IBM PowerHA SystemMirror for AIX*, V6.1 and V7.1 adds support for the IBM System StorageSAN Volume Controller (SVC) Software V6.4. This includes the High Availability and DisasterRecovery (HA/DR) capabilities of IBM PowerHA

    SystemMirror for AIX V6.1 and V7.1.2 Enterprise Edition.

    This support includes SVC V6.4 software running on the IBM Storwize v7000.

    Please refer to the following information for support details.

    IBM SystemStorage SVC

    V6.4AIX V6.1 AIX V7.1

    PowerHA V6.1Enterprise

    Edition

    PowerHA 6.1 APARsIV28142, IV33778, IV33779

    AIX V6.1 TL06 SP03RSCT 3.1.0.3

    PowerHA 6.1 SP3PowerHA 6.1 APARs

    IV28142, IV33778, IV33779AIX V7.1 TL0 SP02

    RSCT 3.1.0.3

    PowerHA V7.1.2Enterprise

    Edition

    PowerHA V7.1 APARsIV33034, IV33780, IV33781,

    IV33782AIX V6.1 TL08 SP01

    RSCT 3.1.0.3

    PowerHA V7.1 APARsIV33034, IV33780, IV33781,

    IV33782AIX V7.1 TL02 SP01

    RSCT 3.1.0.3

    Restrictions:

    The support in this Flash does not cover the 'Change Volumes' facility of SVC Global Mirror.PowerHA SystemMirror does not, at this time, support - and will reject as erroneous -configurations with this facility.IBM intends to remove this restriction in a future release.

    Notes:

    This support includes FC-attach, VIOS/vSCSI, and VIOS/NPIV

    Service can be obtained from the IBM Electronic Fix Distribution site at:http://www.ibm.com/support/fixcentral/

  • 8/10/2019 Ha New Matrix

    34/79

    IBM PowerHA SystemMirror for AIX Supports IBM System Storage SVC Software V6.3November 21, 2012

    IBM PowerHA SystemMirror for AIX*, V6.1 and V7.1 adds support for the IBM System Storage SANVolume Controller (SVC) Software V6.3. This includes High Availability and Disaster Recovery(HA/DR) capability of the IBM PowerHA SystemMirror for AIX V6.1 and V7.1.2 Enterprise Edition.

    This support includes SVC V6.3 software running on the IBM Storwize v7000.

    Please refer to the following information for support details.

    IBM System StorageSVC V6.3

    AIX V5.3 AIX V6.1 AIX V7.1

    PowerHA V6.1Enterprise Edition

    AIX V5.3 TL11, SP01RSCT 2.4.13.0

    AIX V6.1 TL06 SP03RSCT 3.1.0.3

    PowerHA 6.1 SP3AIX V7.1 TL0 SP02

    RSCT 3.1.0.3

    PowerHA V7.1.2Enterprise Edition

    N/A AIX V6.1 TL08 SP01RSCT 3.1.0.3

    AIX V7.1 TL02 SP01RSCT 3.1.0.3

    Notes:

    This support includes FC-attach, VIOS/vSCSI, and VIOS/NPIV

    Restrictions:

    The support in this Flash does not cover the 'Change Volumes' facility of SVC Global Mirror.

    PowerHA SystemMirror does not, at this time, support - and will reject as erroneous -configurations with this facility. IBM intends to remove this restriction in a future release.

  • 8/10/2019 Ha New Matrix

    35/79

    IBM PowerHA SystemMirror for AIX Supports IBM PCI 10Gb Ethernet Adapters (FC 5769/5772)

    July 20, 2012

    IBM PowerHA SystemMirror for AIX* adds support for IBM PCI 10Gb Ethernet Adapters (FC5769/5772).

    Please refer to the following information for support details.

    PCI 10Gb EthernetAdapters (FC 5769/5772)

    AIX V5.3 AIX V6.1 AIX V7.1

    PowerHA V5.5 AIX V5.3 TL12,RSCT 2.4.13.0

    AIX V6.1 TL05,RSCT 2.5.5.2

    PowerHA TL11,AIX V7.1,

    RSCT V3.1.0.3

    PowerHA SystemMirrorV6.1

    AIX V5.3 TL12,RSCT 2.4.13.0

    AIX V6.1 TL05,RSCT 2.5.5.2

    PowerHA V6.1 SP3,AIX V7.1,

    RSCT V3.1.0.3

    PowerHA SystemMirrorV7.1

    Not Supported AIX V6.1 TL06,RSCT V3.1.0.3

    AIX V7.1,RSCT V3.1.0.3

    Clients are advised to obtain the latest service updates for this support.

    Notes:

    Information on Power 7 server support with HACMP V5.3, which is currently supported only viaextended support agreement, is provided in information APAR IZ77613, available online viaIBM support: http://www.ibm.com/support

  • 8/10/2019 Ha New Matrix

    36/79

    IBM PowerHA SystemMirror for AIX V6.1 and V7.1 Supports IBM AIX v5.2 and v5.3 WorkloadPartitions for AIX V7.1July 6, 2012

    IBM PowerHA SystemMirror for AIX* V6.1 and V7.1 for AIX V7.1 supports IBM AIX v5.2 and v5.3Workload Partitions for AIX V7.1 (Compatibility WPARs).

    It is recommended to obtain the latest service updates for this support.

    Please refer to the following information for support details. The specified levels, or later, are requiredfor this support.

    PowerHA SystemMirror AIX

    PowerHA V7.1, SP2PowerHA APAR IZ90890PowerHA APAR IZ91056

    AIX 7.1 TL0 SP2RSCT V3.1.0.3

    PowerHA V6.1, SP3 AIX V7.1 TL0 SP2RSCT V3.1.0.3

    The prerequisites for AIX 5.2 Workload partitions are as follows:

    Versioned WPARs only support POWER7 hardware. Versioned WPARs can be installed only on an AIX 7.1 operating system. The latest available, and supported version of AIX 5.2 is technology level (TL) 10, and service

    pack (SP) 8.Therefore, any backup image that is used to create an AIX 5.2 WPAR must be from an AIX 5.2system running the latest version.

    Restrictions:

    PowerHA does not support devices that are exported to WPARs. Due to this, rootvg disks forVersionedWPARs are not supported by PowerHA.

    PowerHA 7.1 support for Versioned WPAR is restricted to 32 Service IP addresses (perWPAR-enabledResource Group).

    Mixed mode operation, where in some of the nodes of the WPAR-enabled resource group hasVersionedWPAR software installed whereas some other nodes do not, shall not be supported byPowerHA.

    Cloning (via the PowerHA corrective action) of WPAR profile, shall not be supported forVersionedWPARs (in PowerHA).

  • 8/10/2019 Ha New Matrix

    37/79

  • 8/10/2019 Ha New Matrix

    38/79

    PowerHA SystemMirror for AIX Adds Support for the IBM zEnterprise BladeCenter Extension(zBX).June 11, 2012

    IBM PowerHA* (formerly HACMP*) for AIX, V6.1 and V7.1 adds support for the IBM zEnterpriseBladeCenter Extension attached to zEnterprise Systems.

    This support is with IBM BladeCenter* PS701 (8406-71Y) Blades.

    It is recommended to obtain the latest service updates for this support. Please refer to the followinginformation for minimum support levels.

    IBM zEnterpriseBladeCenterExtension

    AIX V5.3 AIX V6.1 AIX V7.1

    PowerHA V5.5 AIX V5.3 TL12,RSCT 2.4.13.0

    AIX V6.1 TL05RSCT 2.5.5.0

    PowerHA V5.5 SP8AIX V7.1

    RSCT V3.1.0.3

    PowerHASystemMirror V6.1

    AIX V5.3 TL12,RSCT 2.4.13.0

    AIX V6.1 TL05RSCT 2.5.5.0

    PowerHA V6.1 SP3AIX V7.1

    RSCT V3.1.0.3

    PowerHASystemMirror V7.1

    Not Supported AIX V6.1 TL06RSCT V3.1.0.3

    AIX V7.1RSCT V3.1.0.3

    Clients are advised to obtain the latest service updates for this support.

    Notes:

    (*) AIX 6.1 TL06 SP3 preferred with RSCT 3.1.0.4 (packaged in CSM PTF 1.7.1.10 installed with AIX 6.1.6.3) isthe preferred baseline for zBX Virtual Servers.

    When using PowerHA 7.1 on AIX 7.1, PowerHA must be at minimum level 7.1.1 and AIX bos.cluster.rte filesetmust be at minimum level 7.1.1.15.

    For blades in zBX model 2458-002, a minimum level MCL011 in the N48129 EC Stream is required. This providesVIOS 2.2.0.12-FP24 SP-02.

    For blades in zBX model 2458-003 the GA level of the H09137 EC Stream is sufficient. It provides VIOS 2.2.1.3.

    When setting up disk volumes used for Power HA, care must be taken to define zBX Virtual Server bootable diskssuch that they are discovered prior to the shared disks used for Power HA resource groups. In most cases this isachieved by defining the bootable disks with LUN IDs lower than the LUN IDs of the shared disks.

    POWER HA DLPAR control is not supported.

    PowerHA is not supported managing IPAT on IPv6 network interfaces/addresses used for zManager PPM control(i.e. "red" network). This network must be unused and left for zManager sole use. Please refer to the zManagerPPM Administration Guide.

    PowerHA is intended for failover within an ensemble and not for business continuity across ensembles.

  • 8/10/2019 Ha New Matrix

    39/79

    IBM PowerHA SystemMirror for AIX Supports the New IBM Flex System p260/p460 ComputeNode (7895-22X/42X)

    May 21, 2012

    IBM PowerHA SystemMirror for AIX adds support for the new IBM Flex System p260/460 Compute

    Node (model 7895-22X/42X).

    Please refer to the following information for support details.

    Flex System p260/p460Compute Node (7895-22X/42X)

    AIX V6.1 AIX V7.1

    PowerHA SystemMirror V6.1 AIX V6.1 TL07 SP03,AIX APAR IV14283,

    RSCT 3.1.0.3

    PowerHA V6.1SP3,

    AIX V7.1 TL01SP03,

    AIX APARIV14284,

    RSCT V3.1.0.3

    PowerHA SystemMirror V7.1 AIX V6.1 TL07 SP03,AIX APAR IV14283,

    RSCT V3.1.0.3

    AIX V7.1 TL01SP03,

    AIX APARIV14284,

    RSCT V3.1.0.3

    Clients are advised to obtain the latest service updates for this support.

    Notes:

    This support includes the built-in: PCIe2 4-port 10GbE Mezz Adapter Dual Port 8Gb FC Mezzanine Card

  • 8/10/2019 Ha New Matrix

    40/79

    IBM PowerHA SystemMirror Supports the IBM System Storage DS8800February 29, 2012

    IBM PowerHA SystemMirror for AIX* V6.1 Enterprise Edition and V7.1 Standard Edition add supportfor the IBM System Storage* DS8800 (2107-951).

    This support includes F/C-attach and NPIV.

    Please refer to the following information for support details.

    DS8800 (2107-951) AIX V6.1 AIX V7.1

    PowerHA V5.5 AIX V6.1 TL05,RSCT 2.5.5.2

    PowerHA TL11,AIX V7.1,

    RSCT V3.1.0.3

    PowerHA SystemMirror V6.1 AIX V6.1 TL05,RSCT 2.5.5.2

    PowerHA V6.1 SP3,AIX V7.1,

    RSCT V3.1.0.3

    PowerHA SystemMirror V7.1 AIX V6.1 TL06,RSCT V3.1.0.3

    AIX V7.1,RSCT V3.1.0.3

    Note: The DS8800 is supported at the same level of function by PowerHA as the currentlysupported DS8000 family.

  • 8/10/2019 Ha New Matrix

    41/79

    IBM PowerHA SystemMirror for AIX Supports the New IBM Power 7 710/730 (8231-E1C/E2C)

    December 09, 2011

    IBM PowerHA SystemMirror for AIX* (formerly HACMP*) adds support for the new IBM Power

    7 710/730 (model 8231-E1C/E2C).

    Please refer to the following information for support details.

    Power 7 710/730(8231-E1C/E2C)

    AIX V5.3 AIX V6.1 AIX V7.1

    PowerHA V5.5 AIX V5.3 TL12,RSCT 2.4.13.0

    AIX V6.1 TL05,RSCT 2.5.5.2

    PowerHA TL11,AIX V7.1,

    RSCT V3.1.0.3

    PowerHASystemMirror V6.1

    AIX V5.3 TL12,RSCT 2.4.13.0

    AIX V6.1 TL05,RSCT 2.5.5.2

    PowerHA V6.1SP3,

    AIX V7.1,RSCT V3.1.0.3

    PowerHASystemMirror V7.1

    Not Supported AIX V6.1 TL06,RSCT V3.1.0.3

    AIX V7.1,RSCT V3.1.0.3

    Clients are advised to obtain the latest service updates for this support.

    Notes: Integrated Virtualization Manager (IVM) is also supported. Information on Power 7 server support with HACMP V5.3, which is currently supported only via

    extended support agreement, is provided in information APAR IZ77613, available online via IBMsupport: http://www.ibm.com/support

  • 8/10/2019 Ha New Matrix

    42/79

    IBM PowerHA SystemMirror for AIX Supports the New IBM Power 7 720/740 (8202-E4C/8205-E6C)

    October 28, 2011

    IBM PowerHA SystemMirror for AIX* (formerly HACMP*) adds support for the new IBM Power 7

    720/740 (model 8202-E4C/8205-E6C).

    Please refer to the following information for support details.

    Power 7 720/740(8202-E4C/8205-E6C)

    AIX V5.3 AIX V6.1 AIX V7.1

    PowerHA V5.5 AIX V5.3 TL12,RSCT 2.4.13.0

    AIX V6.1 TL05,RSCT 2.5.5.2

    PowerHA TL11,AIX V7.1,

    RSCT V3.1.0.3

    PowerHASystemMirror V6.1

    AIX V5.3 TL12,RSCT 2.4.13.0

    AIX V6.1 TL05,RSCT 2.5.5.2

    PowerHA V6.1SP3,

    AIX V7.1,RSCT V3.1.0.3

    PowerHASystemMirror V7.1

    Not Supported AIX V6.1 TL06,RSCT V3.1.0.3

    AIX V7.1,RSCT V3.1.0.3

    Clients are advised to obtain the latest service updates for this support.

    Notes: Integrated Virtualization Manager (IVM) is also supported. Information on Power 7 server support with HACMP V5.3, which is currently supported only via

    extended support agreement, is provided in information APAR IZ77613, available online via IBMsupport: http://www.ibm.com/support

  • 8/10/2019 Ha New Matrix

    43/79

    IBM PowerHA SystemMirror for AIX Supports the New IBM Power 7 770/780 (9117-MMC/9179-MHC)

    December 09, 2011

    IBM PowerHA SystemMirror for AIX* adds support for the new IBM Power 7 770/780 (model 9117-

    MMC/9179-MHC).

    Please refer to the following information for support details.

    Power 7 770/780(9117-MMC/9179-

    MHC)

    AIX V5.3 AIX V6.1 AIX V7.1

    PowerHA V5.5 AIX V5.3 TL12,RSCT 2.4.13.0

    AIX V6.1 TL05,RSCT 2.5.5.2

    PowerHA TL11,AIX V7.1,

    RSCT V3.1.0.3

    PowerHASystemMirror V6.1

    AIX V5.3 TL12,RSCT 2.4.13.0

    AIX V6.1 TL05,RSCT 2.5.5.2

    PowerHA V6.1SP3,

    AIX V7.1,RSCT V3.1.0.3

    PowerHASystemMirror V7.1

    Not Supported AIX V6.1 TL06,RSCT V3.1.0.3

    AIX V7.1,RSCT V3.1.0.3

    Clients are advised to obtain the latest service updates for this support.

    Notes:

    Integrated Virtualization Manager (IVM) is also supported.

    Information on Power 7 server support with HACMP V5.3, which is currently supported only viaextended support agreement, is provided in information APAR IZ77613, available online viaIBM support: http://www.ibm.com/support

  • 8/10/2019 Ha New Matrix

    44/79

    December 09, 2011

    IBM PowerHA SystemMirror for AIX adds support for the new IBM Power 7 775 (model 9125-F2C).

    Please refer to the following information for support details.

    Power 7 775 (9125-

    F2C)

    AIX V5.3 AIX V6.1 AIX V7.1

    PowerHA V5.5 AIX V5.3 TL12,RSCT 2.4.13.0

    AIX V6.1 TL05,RSCT 2.5.5.2

    PowerHA TL11,AIX V7.1,

    RSCT V3.1.0.3

    PowerHASystemMirror V6.1

    AIX V5.3 TL12,RSCT 2.4.13.0

    AIX V6.1 TL05,RSCT 2.5.5.2

    PowerHA V6.1SP3,

    AIX V7.1,RSCT V3.1.0.3

    PowerHASystemMirror V7.1

    Not Supported AIX V6.1 TL06,RSCT V3.1.0.3

    AIX V7.1,RSCT V3.1.0.3

    Clients are advised to obtain the latest service updates for this support.

    Notes: Integrated Virtualization Manager (IVM) is also supported. Information on Power 7 server support with HACMP V5.3, which is currently supported only viaextended support agreement, is provided in information APAR IZ77613, available online via IBMsupport: http://www.ibm.com/support

  • 8/10/2019 Ha New Matrix

    45/79

    IBM PowerHA SystemMirror for AIX supports the IBM Converged Switch B32 (3758-B32)March 31, 2011

    IBM PowerHA SystemMirror for AIX*, v5.4.1, v5.5, v6.1 and v7.1 for AIX v5.3, v6.1 and v7.1 addssupport for the IBM Converged Switch B32 (3758-B32), in combination with the QLogic 10Gb CNA forIBM Power Systems (Feature 5708, 10 Gb FCoE PCIe Dual Port Adapter) and 10Gb Ethernet Pass-

    Thru Module for IBM BladeCenter (FC 1641) and Brocade 2-port 10GbE Converged Network Adapter(FC 5437) for IBM Blades.

    Please refer to the following information for support details.

    IBM Converged SwitchB32

    AIX V5.3 AIX V6.1 AIX V7.1

    HACMP V5.4.1 AIX V5.3, TL11,SP01

    RSCT 2.4.13.0

    AIX V6.1 TL06 SP03RSCT 3.1.0.3

    PowerHA 5.4.1 SP10PowerHA APAR

    IZ96232

    AIX V7.1 TL0 SP02RSCT 3.1.0.3

    PowerHA V5.5 AIX V5.3, TL11,SP01

    RSCT 2.4.13.0

    AIX V6.1 TL06 SP03RSCT 3.1.0.3

    PowerHA 5.5 SP7PowerHA APAR

    IZ96233AIX V7.1 TL0 SP02

    RSCT 3.1.0.3

    PowerHA V6.1 AIX V5.3 TL11,SP01

    RSCT 2.4.13.0

    AIX V6.1 TL06 SP03RSCT 3.1.0.3

    PowerHA 6.1 SP3AIX V7.1 TL0 SP02

    PowerHA APAR

    IZ96235RSCT 3.1.0.3

    PowerHA V7.1 N/A AIX V6.1 TL06 SP03RSCT 3.1.0.3

    AIX V7.1 TL0 SP02PowerHA APAR

    IZ96236RSCT 3.1.0.3

  • 8/10/2019 Ha New Matrix

    46/79

    IBM PowerHA SystemMirror for AIX V6.1 Enterprise Edition Supports the IBM System StorageStorwize V7000September 30, 2011

    IBM PowerHA SystemMirror for AIX* V5.5/6.1 Enterprise Edition adds support for the IBM SystemStorage Storwize V7000 running IBM SAN Volume Controller (SVC) Software v6.2.

    Please refer to the following information for support details.

    IBM SystemStorage Storwize

    V7000

    AIX V5.3 AIX V6.1 AIX V7.1

    PowerHA V5.5 AIX 5.3, TL11,SP01

    RSCT 2.4.13.0

    AIX V6.1 TL04SP03

    RSCT 3.1.0.3

    PowerHA 5.5 SP8AIX V7.1 TL0

    SP02RSCT 3.1.0.3

    PowerHA V6.1 AIX 5.3 TL11,SP01

    RSCT 2.4.13.0

    AIX 6.1 TL06 SP03RSCT 3.1.0.3

    PowerHA 6.1 SP3AIX 7.1 TL0 SP02

    RSCT 3.1.0.3

    Notes:

    Standard Edition already fully supports the Storwize V7000. This announcement is for theaddition of full support with PowerHA SystemMirror V6.1 Enterprise Edition.

    This support includes FC-attach, VIOS/vSCSI, and VIOS/NPIV

  • 8/10/2019 Ha New Matrix

    47/79

    IBM PowerHA SystemMirror for AIX Supports IBM System Storage SVC Software V6.2September 30, 2011

    IBM PowerHA SystemMirror for AIX*, V5.5, V6.1 and V7.1 adds support for the IBM System StorageSAN Volume Controller (SVC) Software V6.2. This includes High Availability and Disaster Recovery(HA/DR) capability of the IBM PowerHA SystemMirror for AIX V6.1 Enterprise Edition.

    Please refer to the following information for support details.

    IBM SystemStorage SVC V6.2

    AIX V5.3 AIX V6.1 AIX V7.1

    PowerHA V5.5 AIX V5.3, TL11,SP01

    RSCT 2.4.13.0

    AIX V6.1 TL04SP03

    RSCT 3.1.0.3

    PowerHA 5.5 SP8AIX V7.1 TL0

    SP02RSCT 3.1.0.3

    PowerHA V6.1 AIX V5.3 TL11,SP01

    RSCT 2.4.13.0

    AIX V6.1 TL06SP03

    RSCT 3.1.0.3

    PowerHA 6.1 SP3AIX V7.1 TL0

    SP02RSCT 3.1.0.3

    PowerHA V7.1 N/A AIX V6.1 TL06SP03

    RSCT 3.1.0.3

    AIX V7.1 TL0SP02

    RSCT 3.1.0.3

    Notes:

    This support includes FC-attach, VIOS/vSCSI, and VIOS/NPIV

  • 8/10/2019 Ha New Matrix

    48/79

    IBM PowerHA SystemMirror for AIX Enterprise Edition Adds Support for the Hewlett Packard(HP) P9500 Disk Array

    August 19, 2011

    IBM PowerHA SystemMirror for AIX V6.1 Enterprise Edition* for AIX V6.1 and V7.1 is adding supportfor the Hewlett Packard (HP) P9500 Disk Array.

    IBM PowerHA SystemMirror for AIX V6.1 Enterprise Edition for AIX V6.1 and V7.1 will now supportHigh Availability and Disaster Recovery (HA/DR) capability with HP P9000 Continuous AccessSynchronous Software replication for the HP P9500 Disk Array.

    Support is available for both FC-attach and NPIV.

    Please refer to the following information for support details.

    Testing was performed with the following levels:

    HP P9500 AIX V6.1 AIX V7.1PowerHA SystemMirror

    V6.1PowerHA V6.1 SP3

    AIX V6.1 TL05RSCT V3.1.0.3

    PowerHA V6.1 SP3AIX V7.1

    RSCT V3.1.0.3

    Clients are advised to obtain the latest available service updates from IBM and HP.

    The following HP software and microcode were used as part of the testing:

    1 HP P9000 Continuous Access Synchronous Software

    2 HP P9000 RAID Manager: 01-23-03/063 P9500 Microcode: 70-02-05-00/004 MPIO: MPIO ODM (5403) devices.fcp.disk.HP.xparray.mpio.rte 5.4.0.3

  • 8/10/2019 Ha New Matrix

    49/79

    PowerHA SystemMirror for AIX Adds Support for the IBM BladeCenter PS703/704June 24, 2011

    IBM PowerHA SystemMirror* for AIX, V5.5, V6.1, and V7.1 adds support for the IBM BladeCenter*PS703 (model 7891-73X) and PS 704 (model 7891-74X).

    Please refer to the following information for support details.

    PS703/704(7891-73Y/74Y)

    AIX V5.3 AIX V6.1 AIX V7.1

    PowerHA V5.5 AIX V5.3 TL12,RSCT 2.4.13.0

    AIX V6.1 TL05RSCT 2.5.5.0

    PowerHA V5.5 SP8AIX V7.1

    RSCT V3.1.0.3

    PowerHASystemMirror V6.1

    AIX V5.3 TL12,RSCT 2.4.13.0

    AIX V6.1 TL05RSCT 2.5.5.0

    PowerHA V6.1 SP3AIX V7.1

    RSCT V3.1.0.3

    PowerHASystemMirror V7.1 Not Supported AIX V6.1 TL06RSCT V3.1.0.3 AIX V7.1RSCT V3.1.0.3

    Clients are advised to obtain the latest service updates for this support.

    Notes:

    Integrated Virtualization Manager (IVM) is also supported. Information on Power 7 server support with HACMP V5.3, which is currently supported only via

    extended support agreement, is provided in information APAR IZ77613, available online viaIBM support: http://www.ibm.com/support

  • 8/10/2019 Ha New Matrix

    50/79

    IBM PowerHA supports IBM System Storage N series N3000, N5000, N6000 and N7000 SystemHardwareMay 11, 2011

    IBM* PowerHA SystemMirror for AIX Versions 5.4.1, 5.5, 6.1 and 7.1 expands support to include the following dualnode models of the IBM System Storage N series:

    N3000 SystemHardware

    N33002859-A20, N34002859-A21, N36002862-A20

    N5000 SystemHardware

    N52002864-(A20, G20), N55002865-(A20, G20)N53002869-(A20, G20), N56002868-(A20, G20)

    N6000 SystemHardware

    N60402858-A20, N60602858-A22, N60702858-A21or with Gateway Feature Code 9551N62102858-C20, N62402858-(C21, E21), N62702858-(C22, E22)or with Gateway Feature Code 9551

    N7000 SystemHardware

    N76002866-(A20, G20), N78002867-(A20, G20)N77002866-(A21, G21), N79002867-(A21, G21)or with Gateway Feature Code 9551

    The N series models are designed to provide fast data access, simultaneous multiprotocol support, expandability, abilityto upgrade, and low maintenance requirements.

    Please refer to the following table for support details.

    IBM System Storage*(models noted above) AIX V5.3 AIX 6.1 AIX 7.1

    PowerHA V5.4.1 AIX 5.3 TL07

    RSCT 2.4.5.4

    AIX 6.10 TL02

    RSCT 2.5.0.0

    HACMP SP10

    AIX V7.1RSCT V3.1.0.3

    PowerHA V5.5 AIX V5.3 TL12RSCT 2.4.13.0

    AIX V6.1 TL05RSCT 2.5.5.0

    PowerHA V5.5 SP7AIX V7.1

    RSCT V3.1.0.3

    PowerHASystemMirror v6.1

    AIX V5.3 TL12RSCT 2.4.13.0

    AIX V6.1 TL05RSCT 2.5.5.0

    PowerHA V6.1 SP3AIX V7.1

    RSCT V3.1.0.3

    PowerHASystemMirror v7.1

    Not Supported AIX V6.1 TL06RSCT V3.1.0.3

    AIX V7.1RSCT V3.1.0.3

    Notes: *Requires Data ONTAP version 7.2.x, 7.3.x and 8.0.x. **Minimum Technology Level/Service Pack.

    Restriction Note:Multipath I/O via iSCSI is not supported at this time. IBM intends to remove this restriction in a futureproduct update.

  • 8/10/2019 Ha New Matrix

    51/79

    IBM PowerHA SystemMir ror for AIX supports the IBM Converged Switch B32 (3758-B32)March 31, 2011

    IBM PowerHA SystemMirror for AIX*, v5.4.1, v5.5, v6.1 and v7.1 for AIX v5.3, v6.1 and v7.1 addssupport for the IBM Converged Switch B32 (3758-B32), in combination with the QLogic 10Gb CNA forIBM Power Systems (Feature 5708, 10 Gb FCoE PCIe Dual Port Adapter) and 10Gb Ethernet Pass-

    Thru Module for IBM BladeCenter (FC 1641) and Brocade 2-port 10GbE Converged Network Adapter(FC 5437) for IBM Blades.

    Please refer to the following information for support details.

    IBM Converged SwitchB32

    AIX V5.3 AIX V6.1 AIX V7.1

    HACMP V5.4.1 AIX V5.3, TL11,SP01

    RSCT 2.4.13.0

    AIX V6.1 TL06 SP03RSCT 3.1.0.3

    PowerHA 5.4.1 SP10PowerHA APAR

    IZ96232

    AIX V7.1 TL0 SP02RSCT 3.1.0.3

    PowerHA V5.5 AIX V5.3, TL11,SP01

    RSCT 2.4.13.0

    AIX V6.1 TL06 SP03RSCT 3.1.0.3

    PowerHA 5.5 SP7PowerHA APAR

    IZ96233AIX V7.1 TL0 SP02

    RSCT 3.1.0.3

    PowerHA V6.1 AIX V5.3 TL11,SP01

    RSCT 2.4.13.0

    AIX V6.1 TL06 SP03RSCT 3.1.0.3

    PowerHA 6.1 SP3AIX V7.1 TL0 SP02

    PowerHA APAR

    IZ96235RSCT 3.1.0.3

    PowerHA V7.1 N/A AIX V6.1 TL06 SP03RSCT 3.1.0.3

    AIX V7.1 TL0 SP02PowerHA APAR

    IZ96236RSCT 3.1.0.3

  • 8/10/2019 Ha New Matrix

    52/79

  • 8/10/2019 Ha New Matrix

    53/79

    IBM PowerHA SystemMirror for AIX supports the IBM System Storage SVC Software v6.1

    March 18, 2011

    IBM PowerHA SystemMirror for AIX*, v5.4.1, v5.5, v6.1 and v7.1 for AIX v5.3, v6.1 and v7.1 addssupport for the IBM System Storage SAN Volume Controller (SVC) Software v6.1. This includes High

    Availability and Disaster Recovery (HA/DR) capability by the Extended Distance (XD) feature of theIBM PowerHA SystemMirror v6.1 Enterprise Edition.

    Please refer to the following information for support details.

  • 8/10/2019 Ha New Matrix

    54/79

    IBM PowerHA SystemMirror for AIX V6.1 and V7.1 adds Support for IBM AIX 5.2 WorkloadPartitions for AIX V7.1

    January 21, 2011

    IBM PowerHA SystemMirror for AIX* V6.1 and V7.1 for AIX V7.1 add support for IBM AIX 5.2 Workload Partitions for AIXV7 (Compatibility WPARs).

    It is recommended to obtain the latest service updates for this support.

    Please refer to the following information for support details. The specified levels, or later, are required for this support.

    PowerHA SystemMirror AIX

    PowerHA V7.1, SP2

    PowerHA APAR IZ90890

    PowerHA APAR IZ91056

    AIX 7.1 TL0 SP2

    RSCT V3.1.0.0

    AIX APAR IZ91004*

    PowerHA V6.1, SP3 AIX V7.1 TL0 SP2

    RSCT V3.1.0.0

    AIX APAR IZ91004*

    The prerequisites for AIX 5.2 Workload partitions are as follows:

    Versioned WPARs only support POWER7 hardware.

    Versioned WPARs can be installed only on an AIX 7.1 operating system.

    The latest available, and supported version of AIX 5.2 is technology level (TL) 10, and service pack (SP) 8.Therefore, any backup image that is used to create an AIX 5.2 WPAR must be from an AIX 5.2 system running

    the latest version.

    Restrictions:

    PowerHA 7.1 support for Versioned WPAR is restricted to 32 Service IP addresses (per WPAR-enabledResource Group).

    Mixed mode operation, where in some of the nodes of the WPAR-enabled resource group has Versioned WPARsoftware installed whereas some other nodes do not, shall not be supported by PowerHA.

    Cloning (via the PowerHA corrective action) of WPAR profile, shall not be supported for Versioned WPARs (inPowerHA).

    Notes:

    APAR IZ91004 is included in RSCT V3.1.0.0 SP4

    WPAR property changes do not take effect until the next time the resource group is brought on line

  • 8/10/2019 Ha New Matrix

    55/79

    IBM PowerHA SystemMirror for AIX Supports IBM VIO Server V2.2 Shared Storage Pool December 10, 2010

    IBM* PowerHA SystemMirror for AIX*, Versions 5.5, 6.1, and 7.1 extends support to include IBMVirtual I/O Server (VIOS) V2.2 Shared Storage Pool virtual SCSI, virtual Ethernet, and NPIV deviceson all PowerHA supported IBM POWER6* and POWER7* processor-based servers along with IBM

    Blades.

    Please refer to the following table for support details.

    AIX Client LPARs Running PowerHA VIOServer

    AIX v5.3 AIX v6.1 AIX v7.1

    PowerHA v5.5 AIX V5.3 TL12,RSCT 2.4.13.0

    AIX 6.1 TL3RSCT 2.5.3.0

    PowerHA V5.5APAR IZ84440,

    AIX V7.1

    2.2.0.11-FP24SP01

    PowerHASystemMirror

    v6.1

    AIX V5.3 TL12,RSCT 2.4.13.0

    AIX V6.1 TL05,RSCT 2.5.5.0

    PowerHA V6.1SP3,

    AIX V7.1,RSCT V3.1.0.0

    2.2.0.11-FP24SP01

    PowerHASystemMirror

    V7.1

    Not Supported AIX V6.1 TL06,RSCT V3.1.0.0

    AIX V7.1,RSCT V3.1.0.0

    2.2.0.11-FP24SP01

    Notes:

    PowerHA XD GLVM is supported with VIO

    PowerHA 7.1 supports cluster communication between hosts using SAN connections that exist between them.More information about the SAN communication can be found in the PowerHA 7.1 documentation. With therelease of VIOS 2.2.0.11-FP24SP01 SAN communication can be established for PowerHA LPARs/nodes evenwhen the storage adapters are virtualized through VIOS. SAN communication is enabled by establishing a VLANbetween the VIOS client and the VIOS (setup instructions are available in AIX documentation). SANcommunication through VIOS can be setup for both NPIV and vSCSI environments.

    PowerHA 7.1 is fully supported with all supported previous levels of IBM VIO Server. However, these levels donot provide support for SANCOM, which requires features only available in VIO Server 2.2.

    Requirements:

    PowerHA and Virtual SCSI/NPIVThe volume group must be defined as Enhanced Concurrent Mode. In general, Enhanced Concurrent Mode is therecommended mode for sharing volume groups in PowerHA clusters because volumes are accessible by multiplePowerHA nodes, resulting in faster fallover in the event of a node failure. If file systems are used on the standby nodes,they are not mounted until the point of fallover so accidental use of data on standby nodes is impossible. If sharedvolumes are accessed directly (without file systems) in Enhanced Concurrent Mode, these volumes are accessible frommultiple nodes so access must be controlled at a higher layer such as databases.

    If any cluster node provides access to shared volumes through VIOS provided by IBM VIO Server V2.1, or by IBM VIO

  • 8/10/2019 Ha New Matrix

    56/79

    Server V2.2 without NPIV, all nodes must do so. This means that disks cannot be shared between an LPAR using by IBMVIO Server V2.1, or by IBM VIO Server V2.2 without NPIV and a node directly accessing those disks. Disks can beshared between an LPAR using VIOS provided by IBM VIO Server V2.1 or 2.2 with NPIV and a node directly accessingthose disks.

    From the point of view of the VIO Server, physical disks (hdisks) are shared, not logical volumes or volume groups. Allvolume group construction and maintenance on these shared disks is done from the PowerHA nodes, not from the VIOServer.

    PowerHA and Virtual EthernetIP Address Takeover (IPAT) via Aliasing must be used. IPAT via Replacement and MAC Address Takeover are notsupported. In general, IPAT via Aliasing is recommended for all PowerHA networks that can support it.

    PowerHAs PCI Hot Plug facility cannot be used. PCI Hot Plug operations are available through the VIO Server. Notethat when a PowerHA node is using Virtual I/O, PowerHAs PCI Hot Plug facility is not meaningful because the I/Oadapters are virtual rather than physical.

    All Virtual Ethernet interfaces defined to PowerHA should be treated as single-adapter networks as described in thePowerHA Planning and Installation Guide. In particular, the netmon.cf facility must be used to monitor and detect failuresof the network interfaces. The netmon.cf file should contain a list of IP addresses chosen so that the physical interfacesmust be up in order to ping. These addresses must be preceded by "!REQ". See the text of APAR IZ01331 for further

    details, available from techlink.austin.ibm.com. Due to the nature of Virtual Ethernet, other mechanisms to detect thefailure of network interfaces are not effective.

    Further configuration-dependent attributes of PowerHA with Virtual EthernetIf the VIO Server has multiple physical interfaces on the same network or if there are two or more PowerHA nodes usingone or more VIO Servers in the same frame, PowerHA will not be informed of (and hence will not react to) individualphysical interface failures. This does not normally limit the availability of the entire cluster because VIOS itself routestraffic around individual failures. The VIOS support is analogous to EtherChannel in this regard. Even in the extreme casewhere all physical interfaces managed by VIO Servers have failed, the VIOS will continue to route traffic from one LPARto another in the same frame, and the virtual Ethernet interface used by PowerHA will not be reported as having failed andPowerHA will not react. Other methods (based on the VIO Server and not PowerHA) must be used for providingnotification of individual adapter failures.

    If the VIO Server has only a single physical interface on a network then a failure of that physical interface will be detectedby PowerHA. However, that failure will isolate the node from the network.

    Although some of these may be viewed as configuration restrictions, many are direct consequences of I/O virtualization.

    All support and restrictions associated with Virtual Ethernet provided by IBM VIO Server V2.2 apply to the correspondinglevel of IVE.

  • 8/10/2019 Ha New Matrix

    57/79

    September 10, 2010

    IBM PowerHA SystemMirror for AIX* (formerly HACMP*) for AIX, V5.4.1, V5.5, V6.1, and V7.1 addssupport for the IBM Power 7 795 (model 9119-FHB).

    Please refer to the following information for support details.

    Power 7 795 (9119-FHB)

    AIX V5.3 AIX V6.1 AIX V7.1

    HACMP V5.4.1 AIX 5.3 TL11 SP1,RSCT 2.4.13.0

    AIX V6.1 TL04SP02,

    RSCT 2.5.4.2

    HACMP V5.4.1APAR IZ84442,

    AIX V7.1,RSCT V3.1.0.0

    PowerHA V5.5 AIX V5.3 TL12,RSCT 2.4.13.0

    AIX V6.1 TL05,RSCT 2.5.5.0

    PowerHA V5.5APAR IZ84440,

    AIX V7.1,RSCT V3.1.0.0

    PowerHASystemMirror V6.1

    AIX V5.3 TL12,RSCT 2.4.13.0

    AIX V6.1 TL05,RSCT 2.5.5.0

    PowerHA V6.1SP3,

    AIX V7.1,RSCT V3.1.0.0

    PowerHASystemMirror V7.1

    Not Supported AIX V6.1 TL06,RSCT V3.1.0.0

    AIX V7.1,RSCT V3.1.0.0

    Clients are advised to obtain the latest service updates for this support.

    Notes:

    Integrated Virtualization Manager (IVM) is also supported. Information on Power 7 server support with HACMP V5.3, which is currently supported only via

    extended support agreement, is provided in information APAR IZ77613, available online viaIBM support: http://www.ibm.com/support

  • 8/10/2019 Ha New Matrix

    58/79

    IBM PowerHA SystemMirror for AIX adds support for the IBM Power 7 720/740 (8205-E4B/E6B)

    September 10, 2010

    IBM PowerHA SystemMirror for AIX* (formerly HACMP*) for AIX, V5.4.1, V5.5, V6.1, and V7.1 addssupport for the IBM Power 7 720/740 (model 8205-E4B/E6B).

    Please refer to the following information for support details.

    Power 7 720/740(8205-E4B/E6B)

    AIX V5.3 AIX V6.1 AIX V7.1

    HACMP V5.4.1 AIX 5.3 TL11 SP1,RSCT 2.4.13.0

    AIX V6.1 TL04SP02,

    RSCT 2.5.4.2

    HACMP V5.4.1APAR IZ84442,

    AIX V7.1,RSCT V3.1.0.0

    PowerHA V5.5 AIX V5.3 TL12,RSCT 2.4.13.0

    AIX V6.1 TL05,RSCT 2.5.5.0

    PowerHA V5.5APAR IZ84440,

    AIX V7.1,RSCT V3.1.0.0

    PowerHASystemMirror V6.1

    AIX V5.3 TL12,RSCT 2.4.13.0

    AIX V6.1 TL05,RSCT 2.5.5.0

    PowerHA V6.1SP3,

    AIX V7.1,RSCT V3.1.0.0

    PowerHASystemMirror V7.1

    Not Supported AIX V6.1 TL06,RSCT V3.1.0.0

    AIX V7.1,RSCT V3.1.0.0

    Clients are advised to obtain the latest service updates for this support.

    Notes:

    Integrated Virtualization Manager (IVM) is also supported. Information on Power 7 server support with HACMP V5.3, which is currently supported only via

    extended support agreement, is provided in information APAR IZ77613, available online viaIBM support: http://www.ibm.com/support

  • 8/10/2019 Ha New Matrix

    59/79

  • 8/10/2019 Ha New Matrix

    60/79

    IBM PowerHA SystemMirror for AIX adds support for IBM AIX V7.1

    September 10, 2010

    IBM PowerHA SystemMirror for AIX* (formerly HACMP*) for AIX V5.4.1, V5.5, V6.1, and V7.1 addssupport for IBM AIX V7.1.

    Please refer to the following information for support details.

    IBM PowerHA AIX V7.1

    HACMP V5.4.1 HACMP V5.4.1 APAR IZ84442,AIX V7.1

    PowerHA V5.5 PowerHA V5.5 APAR IZ84440,AIX V7.1

    PowerHA SystemMirror V6.1 PowerHA V6.1 SP3,AIX V7.1,

    RSCT V3.1.0.0

    PowerHA SystemMirror V7.1 AIX V7.1,RSCT V3.1.0.0

    Clients are advised to obtain the latest service updates for this support.

  • 8/10/2019 Ha New Matrix

    61/79

    IBM PowerHA SystemMirror for AIX supports IBM BladeCenter S with RSSM RAIDed SharedStorage Module

    July 30, 2010

    IBM PowerHA SystemMirror* (formerly HACMP*) for AIX, V5.4.1, V5.5, and V6.1 adds support for the

    IBM BladeCenter* S (model 8886-AC1) with the RSSM RAIDed Shared Storage Module (43W3584)using the following Power Blade models:

    PS700 (model 8406-70Y) and PS701/702 (model 8406-71Y) p7 Blade servers. JS23 (model 7778-23X) and JS43 (model 7778-43X) p6 Blade servers.

    It is recommended to obtain the latest service updates for this support.

    Please refer to the following information for support details.

    BladeCenter S (8886-AC1)with RSSM (43W3584)

    AIX V5.3 AIX V6.1

    HACMP V5.4.1 AIX 5.3, TL12RSCT 2.4.13.0

    AIX V6.1, TL05RSCT 2.5.4.2

    PowerHA V5.5 AIX V5.3 TL12RSCT 2.4.13.0

    AIX V6.1, TL05RSCT 2.5.5.0

    PowerHA SystemMirrorV6.1

    AIX V5.3 TL12RSCT 2.4.13.0

    AIX V6.1, TL05RSCT 2.5.5.0

    Notes:

    Internal SAS storage must be configured as a RAID device. All such devices shared betweenPowerHA nodes must be part of enhanced concurrent mode volume groups.

    This support requires the SAS Connectivity Card (CIOv) for IBM BladeCenter (Part #43W4068/Feature Code 1041).

    Built-in Ethernet adapters are supported for PowerHA use. This includes Integrated VirtualEthernet (IVE).

    Integrated Virtualization Manager (IVM) is also supported.

  • 8/10/2019 Ha New Matrix

    62/79

    IBM PowerHA supports the IBM Total Storage DS3500

    June 15, 2010

    IBM PowerHA* (formerly HACMP*) V5.4.1, V5.5, and V6.1 for AIX V5.3 and V6.1 adds support for theIBM Total Storage DS3500 (1746-C2A/C4A).

    Please refer to the following information for support details.

    IBM TotalStorage DS3500 (1746-C2A/C4A)

    AIX V5.3 AIX V6.1

    PowerHA V5.4.1

    PowerHA 5.4.1SP2

    AIX V5.3 TL8

    RSCT V2.4.8.0

    PowerHA 5.4.1SP2

    AIX V6.1 TL2

    RSCT V2.5.0.0

    PowerHA V5.5

    AIX 5.3 TL9

    RSCTV2.4.10.0

    AIX 6.1 TL2 SP1

    AIX APAR#IZ31208

    RSCT V2.5.2.0

    PowerHA V6.1

    AIX 5.3 TL9

    RSCTV2.4.10.0

    AIX 6.1 TL2 SP1

    AIX APAR#IZ31208

    RSCT V2.5.2.0

    Notes:

    This support is Fibre Channel only. Testing was performed with DS3500 Microcode level 7.70.16.00

  • 8/10/2019 Ha New Matrix

    63/79

  • 8/10/2019 Ha New Matrix

    64/79

    IBM PowerHA SystemMirror Supports the IBMPOWER7 770/780 (9117-MMB/9179-MHB)March 19, 2010Updated to include 5.4.1 and 7.1 support

    IBM PowerHA SystemMirror for AIX* (formerly HACMP*) V5.5 and 6.1 for AIX V6.1 adds support forthe IBM POWER7 770/780 (9117-MMB/9179-MHB).

    Please refer to the following information for support details.

    IBM POWER 7 770/780(9117-MMB/9179-MHB)

    AIX 5.3 AIX 6.1 AIX 7.1

    PowerHA V5.4.1 AIX V5.3, TL11, SP01RSCT 2.4.13.0

    AIX V6.1, TL04, SP02RSCT 2.5.4.2

    PowerHA 5.4.1 SP10AIX V7.1, RSCT 3.1.0.0

    PowerHA V5.5 AIX V5.3, TL11, SP01RSCT 2.4.13.0

    AIX V6.1, TL04, SP03RSCT 2.5.5.0

    PowerHA 5.5 SP5AIX V7.1, RSCT 3.1.0.0

    PowerHA V6.1 AIX V5.3 TL11, SP01RSCT 2.4.13.0

    AIX V6.1, TL04, SP03RSCT 2.5.5.0

    PowerHA 6.1 SP3AIX V7.1, RSCT 3.1.0.0

    PowerHA V7.1 N/A AIX V6.1, TL6RSCT 3.1.0.0

    AIX V7.1, RSCT 3.1.0.0

    Notes

    Built-in serial ports in Power 7 servers are not available for PowerHA use. It is suggested touse disk heart beating instead.

    Built-in Ethernet adapters are supported for PowerHA use. IBM strongly recommends the application of APAR IZ72927 on PowerHA 6.1 clusters that use

    both DLPAR and sub-processor partitions.

  • 8/10/2019 Ha New Matrix

    65/79

    IBM PowerHA SystemMirror for AIX suppor ts the IBM Power 750 (8233-E8B)

    February 12, 2010Updated 6/29/10 to include AIX 5.3 supportUpdated 7/21/10 to include HACMP V5.4.1 supportUpdated 1/21/11 to correct RSCT version numbers

    IBM PowerHA SystemMirror for AIX* (formerly HACMP*) V5.4.1, V5.5, V6.1, and V7.1 for AIX V5.3,V6.1 and V7.1 adds support for the IBM Power 750 (8233-E8B).

    It is recommended to obtain the latest service updates for this support.

    Please refer to the following information for support details.

    IBM POWER 7750

    (8233-E8B)

    AIX V5.3 AIX V6.1 AIX V7.1

    HACMP V5.4.1 AIX V5.3, TL11,

    SP01RSCT 2.4.13.0

    AIX V6.1 TL04 SP03

    RSCT 2.5.4.2

    PowerHA 5.4.1

    SP10AIX V7.1

    RSCT 3.1.0.3

    PowerHA V5.5 AIX V5.3, TL11,SP01

    RSCT 2.4.13.0

    AIX V6.1 TL04 SP03RSCT 2.5.4.2

    PowerHA 5.5 SP7AIX V7.1

    RSCT 3.1.0.3

    PowerHA V6.1 AIX V5.3 TL11, SP01RSCT 2.4.13.0

    AIX V6.1 TL04 SP03RSCT 2.5.4.2

    PowerHA 6.1 SP3AIX V7.1 TL0 SP02

    RSCT 3.1.0.3

    PowerHA V7.1 N/A AIX V6.1 TL06 SP03

    RSCT 3.1.0.3

    AIX V7.1 TL0 SP02

    RSCT 3.1.0.3

    Notes:

    Built-in serial ports in POWER7 servers are not available for PowerHA use. It is suggested touse disk heartbeating instead.

    Built-in Ethernet (IVE) adapters are supported for PowerHA use. Information on POWER7 server support with HACMP V5.3, which is currently supported only

    via extended support agreement, is provided in information APAR IZ77613, available online viaIBM support:

  • 8/10/2019 Ha New Matrix

    66/79

    IBM PowerHA supports the IBM System Storage SVC Software V5.1

    December 22, 2009Updated 2/12/2010 to include 5.5 and 5.4.1 support info.Updated 6/29/2010 replaced APAR #s with appropriate SP levels instead.

    IBM PowerHA SystemMirror for AIX* (formerly HACMP*), V6.1 for AIX V5.3 and V6.1 adds supportfor the IBM System Storage SAN Volume Controller (SVC) Software V5.1. This includes HighAvailability and Disaster Recovery (HA/DR) capability by the Extended Distance (XD) feature of theIBM PowerHA SystemMirror V6.1 Enterprise Edition.

    Please refer to the following information for support details.

    SVC V5.1 AIX V5.3 AIX V6.1

    PowerHA V6.1 PowerHA v6.1 SP1

    AIX 5.3 TL9

    RSCT V2.4.12.0

    PowerHA v6.1 SP1

    AIX 6.1 TL2 SP1

    RSCT V2.5.4.0

    PowerHA V5.5* PowerHA v5.5 SP6

    AIX 5.3 TL9

    RSCT V2.4.10.0

    PowerHA v5.5 SP6

    AIX 6.1 TL2 SP1

    RSCT V2.5.2.0

    PowerHA V5.4.1*

    PowerHA v5.4.1SP8

    AIX 5.3 TL9

    RSCT V2.4.5.0

    PowerHA v5.4.1SP8

    AIX 6.1 TL2 SP1

    RSCT V2.5.2.0

    *Restriction: The Alternate IP address features of the SVC is not available in PowerHA v5.5 andv5.4.1.

  • 8/10/2019 Ha New Matrix

    67/79

    IBM PowerHA SystemMirror supports the IBM System Storage DS5020

    November 6, 2009

    IBM PowerHA SystemMirror for AIX* (formerly HACMP*) V5.4.1, V5.5, and V6.1 for AIX V5.3 andV6.1 adds support the IBM System Storage* DS5020 (1814-20A).

    Please refer to