h configuration capacities - imperial crane...

13
Sany Science & Technology Co., Ltd. 20 Apr 2011 1/13 ANSI B30.5 SCC8300 SERIES 2 SCC8300.H.002.US H CONFIGURATION CAPACITIES Boom 2825A 281,600 Upper Counterweight 125,400 Carbody Counterweight 360 Degree Rating The capacities in the rating chart meet ANSI B30.5 requirements, including SAE J987 and SAE J765. Ratings in this chart are in POUNDS and do not exceed the percentage of tipping specified for this crane by ANSI B30.5. Weight of all load blocks, slings, buckets, hoist lines and other load carrying devices beneath the boom point sheaves, is considered part of the main boom load. Do not lift loads in excess of those shown on this chart. Lifting loads in excess of those shown or operation not in accordance with good operating practice can cause tipping, structural damage or catastrophic failure, Where no capacity is shown, operation is not intended or approved. Shaded areas on this chart indicate ratings that are limited by strength of material or factors other than stability (tipping). WARNING This rating chart is invalid if the crane has been modified or altered by use of other than genuine SANY parts as such modifications or alterations may affect its capacity or safe operation. OPERATING CONDITIONS: Machine to operate in a level position on a firm uniformly supporting surface. Crane operator judgment must be used to allow for dynamic load effects of swinging, hoisting or lowering, travel, wind conditions, as well as adverse operating conditions and physical machine depreciation. Refer to Operator's Manual for operating guidelines. MACHINE TRAVEL: Machine to travel on a firm, level and uniformly supporting surface and boom within boom angle range shown in capacity chart. Refer to Maximum Allowable Travel Specification chart. OPERATING RADIUS: Operating radius is horizontal distance from axis of rotation to center of vertical hoist line or load block. BOOM POINT ELEVATION: Boom point elevation is vertical distance from ground level to centerline of boom point shaft. BOOM ANGLE: Boom angle in degree is angle between horizontal and centerline of boom butt and inserts, and is an indication of operating radius. in all cases, operating radius shall govern capacity.

Upload: votuyen

Post on 15-Aug-2018

231 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: H CONFIGURATION CAPACITIES - Imperial Crane …imperialcrane.com/wp-content/uploads/pdf/specsheets/300 ton Sany... · ANSI B30.5 SCC8300 SERIES 2 SCC8300.H.002.US H CONFIGURATION

Sany Science & Technology Co., Ltd.20 Apr 2011

1/13

ANSI B30.5SCC8300 SERIES 2

SCC8300.H.002.US

H CONFIGURATION CAPACITIESBoom 2825A 281,600 Upper Counterweight125,400 Carbody Counterweight360 Degree Rating

The capacities in the rating chart meet ANSI B30.5 requirements, including SAE J987 and SAE J765. Ratings in this chart are in POUNDS and do not exceed the percentage of tipping specified for this crane by ANSI B30.5.

Weight of all load blocks, slings, buckets, hoist lines and other load carrying devices beneath the boom point sheaves, is considered part of the main boom load. Do not lift loads in excess of those shown on this chart. Lifting loads in excess of those shown or operation not in accordance with good operating practice can cause tipping, structural damage or catastrophic failure, Where no capacity is shown, operation is not intended or approved.

Shaded areas on this chart indicate ratings that are limited by strength of material or factors other than stability (tipping).

WARNING

This rating chart is invalid if the crane has been modified or altered by use of other than genuine SANY parts as such modifications or alterations may affect its capacity or safe operation.

OPERATING CONDITIONS: Machine to operate in a level position on a firmuniformly supporting surface. Crane operator judgment must be used to allow for dynamic load effects of swinging, hoisting or lowering, travel, wind conditions, as well as adverse operating conditions and physical machine depreciation. Refer to Operator's Manual for operating guidelines.

MACHINE TRAVEL:Machine to travel on a firm, level and uniformly supporting surface and boom within boom angle range shown in capacity chart. Refer to Maximum Allowable Travel Specification chart.

OPERATING RADIUS: Operating radius is horizontal distance from axis of rotation to center of vertical hoist line or load block.

BOOM POINT ELEVATION: Boom point elevation is vertical d i s tance f rom ground leve l to centerline of boom point shaft.

BOOM ANGLE: Boom angle in degree is angle between horizontal and centerline of boom butt and inserts, and is an indication of operating radius. in all cases, operating radius shall govern capacity.

Page 2: H CONFIGURATION CAPACITIES - Imperial Crane …imperialcrane.com/wp-content/uploads/pdf/specsheets/300 ton Sany... · ANSI B30.5 SCC8300 SERIES 2 SCC8300.H.002.US H CONFIGURATION

Sany Science & Technology Co., Ltd.20 Apr 2011

2/13

ANSI B30.5SCC8300 SERIES 2

SCC8300.H.002.US

WIRE ROPE

Ratings shown in this chart only apply to cranes equipped with wire ropes that meet the diameter, minimum breaking strength and parts of line requirements as indicated. Consult the SCC8300 Operator’s Manual for a complete listing of current wire rope specifications.

MAST HOIST LINE –20 parts of 26.0 mm diameter DIEPA SKZ 8 1960 wire rope with a minimum breaking strength of 638.0 kN.

MAIN LOAD LINE (ROTATION RESISTANT) –28.0 millimeter diameter DIEPA D 1315 CZ 2160 rotation resistant wire rope with a minimum breaking strength of 778.0 kN.

WIND CONDITIONS

No account is taken of the wind force on the load. The user must consider this effect, which can be substantial for loads with large surface areas. In any wind it is strongly recommended that taglines be used to control the load.

Operation is permitted in steady winds or wind gusts provided capacities are reduced as indicated in the table below.

MAXIMUM WIND SPEED 15 MPH 20 MPH 25MPH 30MPH 35MPH

BOOM LENGTH(FEET)

PERCENT REDUCTION

65.6 ~ 154.2 0 % 0 % 0 % 0 % 0 %

164.0 ~ 213.3 0 % 0 % 0 % 10 % 20 %

223.1 ~ 301.8 0 % 0 % 10 % 20 % 30 %

No operation is permitted when wind conditions exceed 35 MPH. When this condition exists, the following applies.

WINDS UP TO 50 MPH : Lower the load block(s) and weight ball(s) to the ground. Orient the boom in-line with the sideframes / crawlers. Set the boom at a 70 degree boom angle.

WINDS 50 MPH AND ABOVE : Lower the boom to the ground.

Refer to the SCC8300 Operator's Manual for additional information concerning operating the crane in wind.

Page 3: H CONFIGURATION CAPACITIES - Imperial Crane …imperialcrane.com/wp-content/uploads/pdf/specsheets/300 ton Sany... · ANSI B30.5 SCC8300 SERIES 2 SCC8300.H.002.US H CONFIGURATION

Sany Science & Technology Co., Ltd.20 Apr 2011

3/13

ANSI B30.5SCC8300 SERIES 2

SCC8300.H.002.US

ERECTION

Note: Blocks,slings and other load carrying devices must be on the ground during erection.

Erection " OVER-THE-SIDE " is with the boom 90° to the side frames.Erection " OVER-THE-END " is with the boom over the drive end or idler end of the sideframes.

Erection " OVER-THE-END BLOCKED " is with the boom over the idler end of the sideframe with the idler tumblers blocked (See SCC8300 Operator's Manual for blocking instructions).

MAXIMUM BOOM & JIB SELF-ERECTION DATA

BOOM + JIB( CONFIGURATION )

OVER-THE-SIDEOR

OVER-THE-ENDOVER-THE-END BLOCKED

BOOM LENGTH(FEET)

JIB LENGTH(FEET)

BOOM LENGTH(FEET)

JIB LENGTH(FEET)

2825A (H) 282.1 301.8

2825A + 1412A (FJ)

223.0 80.4 223.0 137.8

213.2 100.0

203.4 118.1

193.5 137.8

2825A + 2316A (FJh)223.0 39.4 242.7 59.0

203.4 59.0

Page 4: H CONFIGURATION CAPACITIES - Imperial Crane …imperialcrane.com/wp-content/uploads/pdf/specsheets/300 ton Sany... · ANSI B30.5 SCC8300 SERIES 2 SCC8300.H.002.US H CONFIGURATION

Sany Science & Technology Co., Ltd.20 Apr 2011

4/13

ANSI B30.5SCC8300 SERIES 2

SCC8300.H.002.US

Explanation of Symbols

2825A Boom No.2825A

Crane Counterweight+

Carbody Counterweight

360°360 Degree Rating

Lifting Capacities

Boom Length

Boom Angle

OperatingRadius

Boom Elevation

Page 5: H CONFIGURATION CAPACITIES - Imperial Crane …imperialcrane.com/wp-content/uploads/pdf/specsheets/300 ton Sany... · ANSI B30.5 SCC8300 SERIES 2 SCC8300.H.002.US H CONFIGURATION

2825A281.6Klb

+125.4Klb 360°

Sany Science & Technology Co., Ltd.20 Apr 2011

5/13

ANSI B30.5SCC8300 SERIES 2

SCC8300.H.002.US

17.1 83.1 62.6 660 18 83.1 62.6 630.9 20 81.1 62.2 568.4 22 79.4 61.9 536.3 24 77.6 61.4 498.9 26 75.7 60.8 456.2 28 73.9 60.0 424.2 30 72.0 59.2 394.9 32 70.2 58.4 369.8 34 68.2 57.5 348.9 36 66.2 56.5 330.7 38 64.3 55.5 312.5 40 62.3 54.4 295.8 45 57.0 50.8 262.6 50 51.3 46.5 234.5 55 45.1 41.4 208.7 60 34.1 31.6 162.2

20 82.4 72.4 565.8 22 80.8 71.8 531.1 24 79.2 71.3 492.0 26 77.6 70.9 448.5 28 76.0 70.4 419.5 30 74.4 69.7 392.9 32 72.8 68.9 368.3 34 71.2 68.1 347.6 36 69.6 67.3 329.5 38 67.9 66.5 311.4 40 66.3 65.5 294.7 45 61.9 62.5 261.0 50 57.3 59.1 233.8 55 52.5 55.3 208.8 60 47.4 50.8 185.4 65 41.6 45.0 165.9 70 34.8 37.7 150.1

20 83.2 82.2 563.2 22 81.9 81.9 525.8 24 80.5 81.5 485.0 26 79.0 81.0 440.9 28 77.7 80.5 414.8 30 76.3 79.9 390.8 32 74.9 79.3 366.7 34 73.4 78.7 346.3 36 72.0 78.0 328.3 38 70.6 77.3 310.2 40 69.2 76.5 293.5 45 65.5 74.0 259.6 50 61.6 71.1 233.1 55 57.6 67.9 208.6 60 53.4 64.2 185.2 65 48.8 59.6 165.9 70 44.0 54.2 150.2 75 38.5 47.9 136.5

65.6ft 75.4ft 85.3ft

° ° °ft Klbft ft Klbft ft Klbft

Page 6: H CONFIGURATION CAPACITIES - Imperial Crane …imperialcrane.com/wp-content/uploads/pdf/specsheets/300 ton Sany... · ANSI B30.5 SCC8300 SERIES 2 SCC8300.H.002.US H CONFIGURATION

2825A281.6Klb

+125.4Klb 360°

Sany Science & Technology Co., Ltd.20 Apr 2011

6/13

ANSI B30.5SCC8300 SERIES 2

SCC8300.H.002.US

24 81.5 91.7 479.1 26 80.2 91.2 436.4 28 79.0 90.7 412.2 30 77.8 90.1 389.7 32 76.5 89.7 365.6 34 75.3 89.2 345.1 36 74.0 88.5 327.0 38 72.8 87.8 308.8 40 71.5 87.0 292.1 45 68.2 84.7 258.5 50 64.8 82.3 232.3 55 61.4 79.5 208.1 60 57.8 76.4 185.2 65 54.1 72.7 165.9 70 50.1 68.5 150.2 75 45.8 63.5 136.5 80 41.2 57.6 124.6 85 36.2 50.9 114.6

24 82.3 101.5 475.3 26 81.1 101.0 434.0 28 80.0 100.7 410.6 30 78.9 100.3 388.5 32 77.8 99.9 363.9 34 76.7 99.4 343.3 36 75.6 98.8 325.3 38 74.4 98.2 307.4 40 73.2 97.6 290.8 45 70.3 95.5 257.3 50 67.4 93.3 231.7 55 64.3 90.8 207.9 60 61.2 88.0 185.1 65 58.0 85.0 165.9 70 54.6 81.3 150.2 75 51.0 77.2 136.6 80 47.3 72.4 124.8 85 43.3 67.2 114.6 90 39.0 60.8 106.0 95 34.1 53.4 98.1

24 83.0 111.4 468.0 26 81.9 111.2 427.4 28 80.9 110.9 402.2 30 79.9 110.5 378.8 32 78.9 110.1 355.0 34 77.9 109.5 335.5 36 76.9 108.9 318.9 38 75.8 108.3 302.2 40 74.8 107.7 286.9 45 72.1 105.9 255.8 50 69.4 104.0 231.2 55 66.7 101.9 207.6 60 64.0 99.5 184.4 65 61.1 96.5 165.2 70 58.1 93.3 149.7 75 55.0 89.7 136.2 80 51.8 85.7 124.3 85 48.5 81.3 114.1 90 45.0 76.1 105.7 95 41.1 70.4 98.0 100 36.9 63.8 91.0 105 32.4 56.1 84.9

95.1ft 105.0ft 114.8ft

° ° °ft Klbft ft Klbft ft Klbft

Page 7: H CONFIGURATION CAPACITIES - Imperial Crane …imperialcrane.com/wp-content/uploads/pdf/specsheets/300 ton Sany... · ANSI B30.5 SCC8300 SERIES 2 SCC8300.H.002.US H CONFIGURATION

2825A281.6Klb

+125.4Klb 360°

Sany Science & Technology Co., Ltd.20 Apr 2011

7/13

ANSI B30.5SCC8300 SERIES 2

SCC8300.H.002.US

24 83.5 121.5 460.6 26 82.6 121.1 420.7 28 81.6 120.7 393.8 30 80.7 120.3 369.5 32 79.8 119.9 348.1 34 78.8 119.5 329.9 36 77.9 119.0 313.9 38 77.0 118.5 297.8 40 76.0 117.9 283.1 45 73.5 116.4 254.3 50 71.1 114.7 230.7 55 68.7 112.7 207.4 60 66.1 110.4 184.1 65 63.6 107.9 164.8 70 61.0 105.0 149.2 75 58.2 101.8 135.8 80 55.4 98.4 124.1 85 52.5 94.4 113.9 90 49.5 90.2 105.5 95 46.2 85.3 97.8 100 42.9 79.8 90.8 105 39.3 73.8 84.4 110 35.2 66.5 78.9

28 82.2 130.9 388.9 30 81.4 130.5 364.7 32 80.5 130.1 342.0 34 79.7 129.6 323.3 36 78.8 129.1 307.3 38 77.9 128.6 291.4 40 77.0 128.1 277.0 45 74.8 126.8 250.4 50 72.6 125.2 225.6 55 70.4 123.3 202.5 60 68.1 121.3 181.5 65 65.7 119.1 163.9 70 63.3 116.4 148.7 75 60.8 113.5 135.4 80 58.3 110.3 123.7 85 55.8 106.8 113.7 90 53.0 103.1 105.1 95 50.2 98.9 97.4 100 47.3 94.2 90.4 105 44.3 89.2 84.2 110 41.0 83.2 78.6 115 37.5 76.7 73.7

28 82.8 140.7 384.0 30 82.0 140.4 360.0 32 81.2 140.2 335.9 34 80.4 139.8 316.8 36 79.6 139.3 300.9 38 78.8 138.8 285.1 40 78.0 138.3 270.9 45 75.9 137.0 245.1 50 73.8 135.6 220.1 55 71.7 133.8 198.0 60 69.6 131.8 179.2 65 67.5 129.8 163.3 70 65.3 127.4 148.3 75 63.0 124.7 135.0 80 60.7 121.9 123.3 85 58.3 119.0 113.3 90 56.0 115.5 104.7 95 53.5 111.7 96.9 100 51.0 107.5 89.9 105 48.3 103.0 83.8 110 45.5 98.0 78.3 115 42.5 92.5 73.3 120 39.4 86.5 68.7 125 36.1 79.9 64.6 130 32.3 71.8 60.6

124.6ft 134.5ft 144.3ft

° ° °ft Klbft ft Klbft ft Klbft

Page 8: H CONFIGURATION CAPACITIES - Imperial Crane …imperialcrane.com/wp-content/uploads/pdf/specsheets/300 ton Sany... · ANSI B30.5 SCC8300 SERIES 2 SCC8300.H.002.US H CONFIGURATION

2825A281.6Klb

+125.4Klb 360°

Sany Science & Technology Co., Ltd.20 Apr 2011

8/13

ANSI B30.5SCC8300 SERIES 2

SCC8300.H.002.US

28 83.2 150.7 377.9 30 82.5 150.5 353.7 32 81.8 150.1 331.0 34 81.0 149.7 312.0 36 80.3 149.3 295.6 38 79.5 148.9 279.1 40 78.8 148.5 264.6 45 76.8 147.2 239.7 50 74.9 145.8 215.6 55 72.9 144.1 194.2 60 70.9 142.4 175.8 65 68.9 140.6 160.4 70 67.0 138.5 146.9 75 64.9 136.1 134.3 80 62.7 133.4 122.6 85 60.6 130.4 112.8 90 58.4 127.2 104.2 95 56.2 123.8 96.6 100 53.8 120.1 271.5 105 51.5 116.1 833.3 110 49.0 111.9 251.0 115 46.4 107.1 73.0 120 43.7 101.8 68.5 125 40.9 96.1 64.2 130 37.9 89.5 60.4 135 34.6 82.3 56.9

30 82.9 160.3 347.4 32 82.3 159.9 326.0 34 81.6 159.6 307.7 36 80.8 159.3 291.3 38 80.1 159.0 275.0 40 79.4 158.7 260.4 45 77.6 157.4 235.0 50 75.8 156.1 211.3 55 74.0 154.6 190.5 60 72.2 152.9 172.6 65 70.3 151.1 157.7 70 68.4 149.2 145.0 75 66.5 146.9 133.1 80 64.6 144.4 122.0 85 62.6 141.9 111.9 90 60.6 138.9 103.5 95 58.5 135.7 95.8 100 56.4 132.4 88.8 105 54.3 128.9 82.7 110 52.0 124.9 77.2 115 49.7 120.6 72.2 120 47.4 115.9 67.6 125 44.8 110.9 63.5 130 42.2 105.3 59.5 135 39.5 99.3 56.1 140 36.6 92.6 52.9

30 83.3 170.2 336.5 32 82.7 170.0 318.2 34 82.0 169.7 301.2 36 81.3 169.3 284.9 38 80.7 168.9 268.7 40 80.0 168.5 254.4 45 78.3 167.5 230.2 50 76.6 166.3 207.2 55 74.9 164.9 186.9 60 73.2 163.4 169.5 65 71.5 161.6 154.8 70 69.7 159.7 142.4 75 67.9 157.7 131.4 80 66.1 155.6 121.3 85 64.3 153.1 111.5 90 62.4 150.3 103.1 95 60.5 147.4 95.4 100 58.6 144.3 88.4 105 56.6 141.1 82.2 110 54.5 137.3 76.8 115 52.5 133.4 71.8 120 50.4 129.2 67.2 125 48.2 124.7 63.1 130 45.8 119.9 59.3 135 43.4 114.6 55.8 140 40.9 108.8 52.5 145 38.2 102.5 49.5 150 35.3 95.5 46.6 155 32.3 87.4 44.1

154.2ft 164ft 173.8ft

° ° °ft Klbft ft Klbft ft Klbft

Page 9: H CONFIGURATION CAPACITIES - Imperial Crane …imperialcrane.com/wp-content/uploads/pdf/specsheets/300 ton Sany... · ANSI B30.5 SCC8300 SERIES 2 SCC8300.H.002.US H CONFIGURATION

2825A281.6Klb

+125.4Klb 360°

Sany Science & Technology Co., Ltd.20 Apr 2011

9/13

ANSI B30.5SCC8300 SERIES 2

SCC8300.H.002.US

30 83.7 180.3 325.8 35 82.1 179.5 286.6 40 80.6 178.7 248.5 45 79.0 177.7 225.3 50 77.4 176.5 203.0 55 75.8 175.1 183.3 60 74.1 173.6 166.5 65 72.5 172.1 152.1 70 70.8 170.4 139.9 75 69.2 168.4 129.1 80 67.5 166.1 119.4 85 65.8 163.8 110.7 90 64.1 161.4 102.4 95 62.3 158.7 94.7 100 60.4 155.9 87.7 105 58.6 152.9 81.6 110 56.8 149.4 76.1 115 54.8 145.9 71.2 120 52.9 142.2 66.7 125 50.9 138.2 62.4 130 48.8 133.6 58.7 135 46.6 128.8 55.3 140 44.4 123.6 52.0 145 42.1 118.1 48.9 150 39.6 112.0 46.1 155 37.0 105.4 43.4 160 34.2 98.0 40.9

35 82.5 189.5 282.0 40 81.0 188.5 245.6 45 79.6 187.5 221.1 50 78.1 186.5 199.2 55 76.5 185.4 180.0 60 75.0 184.1 163.5 65 73.4 182.3 149.4 70 71.9 180.8 137.6 75 70.3 179.0 127.0 80 68.7 176.9 117.5 85 67.1 174.6 109.2 90 65.4 172.4 101.4 95 63.8 169.9 94.0 100 62.1 167.1 87.2 105 60.4 164.4 81.1 110 58.6 161.3 75.7 115 56.9 158.0 70.7 120 55.1 154.4 66.1 125 53.3 150.7 62.0 130 51.4 146.7 58.2 135 49.4 142.3 54.8 140 47.4 137.7 51.5 145 45.2 132.8 48.4 150 43.1 127.3 45.7 155 40.8 121.4 43.0 160 38.4 115.1 40.5 165 35.9 108.4 38.2 170 33.2 100.6 36.1

35 82.9 199.5 277.3 40 81.5 198.7 242.5 45 80.1 197.7 216.9 50 78.6 196.7 195.2 55 77.2 195.6 176.4 60 75.7 194.3 160.2 65 74.3 192.8 146.5 70 72.8 191.1 134.9 75 71.3 189.3 124.5 80 69.8 187.5 115.2 85 68.3 185.5 107.0 90 66.7 183.3 99.9 95 65.1 180.8 93.0 100 63.6 178.3 86.4 105 62.0 175.9 80.2 110 60.4 172.8 74.8 115 58.7 169.7 69.9 120 57.0 166.5 65.4 125 55.3 163.2 61.3 130 53.5 159.4 57.3 135 51.7 155.3 53.9 140 49.9 150.9 50.7 145 48.1 146.4 47.7 150 46.1 141.6 44.8 155 44.0 136.5 42.3 160 41.9 130.9 39.8 165 39.6 124.7 37.5 170 37.4 118.3 35.4 175 34.9 111.1 33.3

183.7ft 193.5ft 203.4ft

° ° °ft Klbft ft Klbft ft Klbft

Page 10: H CONFIGURATION CAPACITIES - Imperial Crane …imperialcrane.com/wp-content/uploads/pdf/specsheets/300 ton Sany... · ANSI B30.5 SCC8300 SERIES 2 SCC8300.H.002.US H CONFIGURATION

2825A281.6Klb

+125.4Klb 360°

Sany Science & Technology Co., Ltd.20 Apr 2011

10/13

ANSI B30.5SCC8300 SERIES 2

SCC8300.H.002.US

35 83.2 209.3 252.8 40 81.9 208.6 234.9 45 80.5 207.8 211.4 50 79.2 206.9 191.0 55 77.8 205.8 173.1 60 76.4 204.4 157.4 65 75.0 203.0 143.8 70 73.6 201.5 132.5 75 72.2 199.8 122.3 80 70.7 198.0 113.2 85 69.3 196.0 105.2 90 67.8 194.0 98.1 95 66.4 191.8 91.7 100 64.9 189.5 85.6 105 63.4 187.0 79.6 110 61.9 184.2 74.1 115 60.3 181.3 69.3 120 58.7 178.3 64.8 125 57.1 175.0 60.6 130 55.5 171.4 56.9 135 53.8 167.8 53.4 140 52.1 163.9 50.1 145 50.4 159.9 47.1 150 48.5 155.3 44.4 155 46.7 150.5 41.9 160 44.8 145.3 39.4 165 42.8 139.9 37.1 170 40.7 134.2 34.9 175 38.6 128.0 32.9 180 36.4 121.2 30.9 185 34.0 113.7 29.1 190 31.5 105.8 27.4

40 82.2 218.7 228.9 45 80.9 217.7 207.5 50 79.6 216.7 187.5 55 78.4 215.7 169.7 60 77.1 214.6 154.3 65 75.7 213.1 141.2 70 74.4 211.8 130.0 75 73.0 210.3 120.0 80 71.6 208.5 111.1 85 70.3 206.8 103.2 90 68.9 204.8 96.3 95 67.5 202.7 89.9 100 66.1 200.3 84.1 105 64.7 197.8 78.7 110 63.2 195.3 73.5 115 61.7 192.6 68.6 120 60.3 189.8 64.1 125 58.8 186.8 60.0 130 57.3 183.5 56.0 135 55.7 180.1 52.6 140 54.1 176.4 49.4 145 52.5 172.4 46.4 150 50.8 168.4 43.7 155 49.1 164.0 41.2 160 47.3 159.3 38.7 165 45.5 154.5 36.4 170 43.7 149.2 34.3 175 41.8 143.6 32.2 180 39.7 137.6 30.3 185 37.6 131.1 28.5 190 35.4 124.1 26.8 195 33.1 116.3 25.1

40 82.6 228.6 223.7 45 81.3 227.8 204.1 50 80.1 226.9 184.2 55 78.9 225.8 166.4 60 77.6 224.5 151.4 65 76.3 223.2 138.5 70 75.0 222.0 127.5 75 73.8 220.6 117.7 80 72.5 219.0 108.9 85 71.2 217.3 101.3 90 69.8 215.3 94.3 95 68.5 213.3 88.0 100 67.2 211.2 82.3 105 65.8 209.0 76.9 110 64.4 206.5 72.2 115 63.0 203.8 67.6 120 61.7 201.1 63.2 125 60.2 198.3 59.1 130 58.8 195.3 55.4 135 57.3 192.0 51.9 140 55.8 188.5 48.7 145 54.3 184.9 45.7 150 52.8 181.1 42.8 155 51.2 177.0 40.3 160 49.6 172.7 37.8 165 47.9 168.3 35.5 170 46.2 163.3 33.4 175 44.5 158.4 31.4 180 42.6 152.9 29.6 185 40.7 147.0 27.8 190 38.8 140.8 26.1 195 36.7 134.0 24.4 200 34.5 126.8 22.8

213.2ft 223.0ft 232.9ft

° ° °ft Klbft ft Klbft ft Klbft

Page 11: H CONFIGURATION CAPACITIES - Imperial Crane …imperialcrane.com/wp-content/uploads/pdf/specsheets/300 ton Sany... · ANSI B30.5 SCC8300 SERIES 2 SCC8300.H.002.US H CONFIGURATION

2825A281.6Klb

+125.4Klb 360°

Sany Science & Technology Co., Ltd.20 Apr 2011

11/13

ANSI B30.5SCC8300 SERIES 2

SCC8300.H.002.US

40 82.9 238.4 218.4 45 81.7 237.6 200.7 50 80.5 236.7 181.0 55 79.3 235.7 163.3 60 78.1 234.7 148.5 65 76.8 233.4 136.0 70 75.6 232.2 125.2 75 74.4 230.8 115.6 80 73.2 229.3 106.9 85 72.0 227.8 99.3 90 70.7 225.8 92.5 95 69.4 223.8 86.2 100 68.2 221.8 80.6 105 66.9 219.8 75.4 110 65.6 217.3 70.8 115 64.2 214.8 66.5 120 62.9 212.4 62.4 125 61.6 209.8 58.4 130 60.2 206.7 54.7 135 58.9 203.8 51.3 140 57.5 200.6 48.1 145 56.0 197.1 45.1 150 54.6 193.5 42.2 155 53.1 189.7 39.7 160 51.5 185.7 37.2 165 50.0 181.5 34.9 170 48.4 177.0 32.8 175 46.8 172.4 30.9 180 45.2 167.3 29.0 185 43.4 162.0 27.2 190 41.6 156.5 25.5 195 39.8 150.3 23.7 200 37.8 143.8 22.3 205 35.8 137.0 20.9 210 33.8 129.6 19.4 215 31.5 121.3 18.0

40 83.2 248.3 211.7 45 82.0 247.5 197.5 50 80.9 246.8 177.9 55 79.7 245.9 160.1 60 78.6 244.9 145.7 65 77.3 243.6 133.3 70 76.2 242.3 122.9 75 75.1 241.1 113.4 80 73.9 239.7 105.0 85 72.7 238.0 97.5 90 71.5 236.3 90.9 95 70.2 234.5 84.7 100 69.0 232.6 79.1 105 67.8 230.6 74.1 110 66.6 228.4 69.3 115 65.3 226.0 65.1 120 64.0 223.5 61.2 125 62.8 220.9 57.6 130 61.5 218.2 54.0 135 60.2 215.3 50.6 140 58.8 212.2 47.4 145 57.5 208.9 44.4 150 56.1 205.7 41.5 155 54.8 202.0 39.0 160 53.4 198.2 36.6 165 51.9 194.4 34.4 170 50.4 190.1 32.3 175 48.9 185.7 30.2 180 47.3 181.0 28.3 185 45.8 176.2 26.5 190 44.1 171.2 24.8 195 42.4 165.5 23.3 200 40.7 159.6 21.7 205 38.9 153.4 20.3 210 37.0 147.0 19.0 215 35.0 139.7 17.6 220 32.9 132.1 16.4

40 83.5 258.4 205.1 45 82.3 257.6 194.2 50 81.2 256.7 174.8 55 80.1 255.8 157.0 60 79.0 255.0 143.1 65 77.8 253.7 130.9 70 76.8 252.5 120.6 75 75.7 251.3 111.3 80 74.5 249.9 103.0 85 73.4 248.5 95.5 90 72.2 246.8 89.0 95 71.0 245.0 83.0 100 69.8 243.1 77.5 105 68.7 241.1 72.3 110 67.5 239.1 67.9 115 66.3 236.8 63.7 120 65.1 234.4 59.7 125 63.9 232.1 56.0 130 62.7 229.4 52.8 135 61.4 226.6 49.8 140 60.1 223.8 46.8 145 58.8 220.7 43.7 150 57.5 217.5 40.8 155 56.2 214.0 38.3 160 54.9 210.5 35.8 165 53.5 206.9 33.6 170 52.2 202.9 31.5 175 50.8 198.7 29.6 180 49.3 194.4 27.6 185 47.8 190.1 25.8 190 46.4 185.3 24.1 195 44.8 180.0 22.6 200 43.2 174.6 21.1 205 41.6 169.0 19.7 210 39.9 163.1 18.3 215 38.1 156.8 16.9 220 36.2 149.8 15.7 225 34.3 142.4 14.5

242.7ft 252.6ft 262.4ft

° ° °ft Klbft ft Klbft ft Klbft

Page 12: H CONFIGURATION CAPACITIES - Imperial Crane …imperialcrane.com/wp-content/uploads/pdf/specsheets/300 ton Sany... · ANSI B30.5 SCC8300 SERIES 2 SCC8300.H.002.US H CONFIGURATION

2825A281.6Klb

+125.4Klb 360°

Sany Science & Technology Co., Ltd.20 Apr 2011

12/13

ANSI B30.5SCC8300 SERIES 2

SCC8300.H.002.US

40 83.7 268.3 180.1 45 82.6 267.5 169.7 50 81.5 266.8 163.0 55 80.5 265.9 153.4 60 79.4 264.9 140.3 65 78.3 263.9 128.4 70 77.3 262.7 118.3 75 76.2 261.4 109.3 80 75.0 260.1 101.1 85 74.0 258.6 93.7 90 72.9 257.1 87.3 95 71.8 255.5 81.4 100 70.6 253.6 76.0 105 69.5 251.6 71.0 110 68.3 249.6 66.4 115 67.2 247.5 62.2 120 66.1 245.2 58.4 125 64.9 242.9 54.9 130 63.7 240.4 51.5 135 62.5 237.7 48.4 140 61.4 235.0 45.5 145 60.2 232.2 42.9 150 58.9 229.2 40.2 155 57.6 226.0 37.7 160 56.4 222.6 35.3 165 55.1 219.1 33.1 170 53.8 215.3 30.9 175 52.5 211.6 28.9 180 51.1 207.6 27.0 185 49.7 203.2 25.2 190 48.3 198.8 23.5 195 46.8 194.0 22.0 200 45.4 189.1 20.4 205 43.9 184.0 19.0 210 42.3 178.5 17.6 215 40.7 172.4 16.3 220 39.0 166.3 15.1 225 37.3 159.8 13.9 230 35.5 152.7 12.7 235 33.6 145.2 11.7 240 31.5 137.1 10.6

50 81.8 276.6 159.6 55 80.8 275.9 149.9 60 79.8 275.1 137.5 65 78.7 274.0 126.0 70 77.7 272.8 116.1 75 76.6 271.6 107.1 80 75.6 270.3 98.9 85 74.6 268.8 91.7 90 73.5 267.3 85.3 95 72.4 265.8 79.4 100 71.4 264.1 74.0 105 70.3 262.1 69.2 110 69.1 260.3 64.8 115 68.1 258.3 60.7 120 67.0 256.0 56.9 125 65.8 253.8 53.4 130 64.8 251.5 50.0 135 63.6 248.9 47.0 140 62.5 246.3 44.2 145 61.3 243.7 41.4 150 60.1 240.7 38.9 155 58.9 237.7 36.6 160 57.7 234.4 34.4 165 56.5 230.9 32.2 170 55.2 227.4 30.1 175 54.0 223.9 28.0 180 52.8 220.2 26.1 185 51.4 216.1 24.3 190 50.1 211.9 22.6 195 48.7 207.3 21.1 200 47.3 202.7 19.5 205 45.9 197.9 18.1 210 44.5 192.9 16.8 215 43.0 187.4 15.4 220 41.4 181.7 14.2 225 39.9 175.7 13.0 230 38.3 169.5 11.8 235 36.5 162.7 10.8 240 34.7 155.6 9.9 245 32.9 147.9 8.8

50 82.1 286.8 150.8 55 81.1 285.9 142.1 60 80.1 284.9 132.6 65 79.1 283.9 123.2 70 78.1 282.9 113.8 75 77.1 281.8 104.9 80 76.0 280.5 97.0 85 75.1 279.3 89.9 90 74.1 277.8 83.7 95 73.0 276.1 77.9 100 72.0 274.3 72.5 105 71.0 272.6 67.7 110 69.9 270.8 63.2 115 68.9 268.9 59.2 120 67.8 266.9 55.5 125 66.7 264.7 52.0 130 65.7 262.4 48.9 135 64.5 259.9 45.8 140 63.4 257.4 42.9 145 62.4 254.9 40.3 150 61.2 252.1 37.8 155 60.1 249.2 35.4 160 58.9 246.0 33.2 165 57.8 242.8 31.1 170 56.6 239.6 29.1 175 55.4 236.1 27.3 180 54.2 232.5 25.6 185 53.0 228.7 23.8 190 51.7 224.6 22.1 195 50.4 220.6 20.4 200 49.1 216.3 18.9 205 47.8 211.8 17.5 210 46.5 207.0 16.1 215 45.0 202.0 14.9 220 43.6 196.6 13.6 225 42.2 191.0 12.3 230 40.7 185.3 11.1 235 39.1 179.0 10.1 240 37.5 172.6 9.2 245 35.8 165.8 8.2 250 34.0 158.3 7.2 255 32.2 150.3 6.4

272.2ft 282.1ft 291.9ft

° ° °ft Klbft ft Klbft ft Klbft

Page 13: H CONFIGURATION CAPACITIES - Imperial Crane …imperialcrane.com/wp-content/uploads/pdf/specsheets/300 ton Sany... · ANSI B30.5 SCC8300 SERIES 2 SCC8300.H.002.US H CONFIGURATION

2825A281.6Klb

+125.4Klb 360°

Sany Science & Technology Co., Ltd.20 Apr 2011

13/13

ANSI B30.5SCC8300 SERIES 2

SCC8300.H.002.US

50 82.4 296.6 142.3 55 81.4 295.9 134.4 60 80.4 295.1 127.7 65 79.5 294.1 122.2 70 78.5 293.1 111.4 75 77.5 292.0 101.7 80 76.5 290.7 93.9 85 75.6 289.5 87.0 90 74.6 288.0 81.0 95 73.6 286.4 75.4 100 72.6 284.8 70.1 105 71.6 283.1 65.0 110 70.6 281.3 60.9 115 69.6 279.4 57.0 120 68.5 277.5 53.3 125 67.5 275.5 49.8 130 66.5 273.2 46.7 135 65.5 270.9 43.6 140 64.4 268.6 40.8 145 63.4 266.1 38.3 150 62.3 263.3 35.9 155 61.2 260.6 33.6 160 60.1 257.7 31.4 165 59.0 254.6 29.4 170 57.8 251.4 27.3 175 56.7 248.1 25.6 180 55.6 244.7 24.0 185 54.4 241.1 22.3 190 53.2 237.4 20.6 195 51.9 233.4 19.1 200 50.7 229.3 17.7 205 49.5 225.0 16.4 210 48.2 220.5 15.0 215 46.9 215.7 13.8 220 45.6 210.8 12.6 225 44.3 205.7 11.4 230 42.8 200.4 10.0 235 41.4 194.6 8.9 240 39.9 188.5 7.7 245 38.4 182.1 6.6 250 36.8 175.5 5.4 255 35.1 168.6 4.6

301.8ft

°ft Klbft