REF: 230518

Base Units - Guide for Doors & Drawer Sizes: Standard layout shown. Suitable for Made-to-Measure.

Hinge Drillings – Door Drillings for Standard Base Unit with 100mm Drillings (Includes Clic Box)

• Door Top Hinge = 71mm

• Door Bottom Hinge = 98mm

Base Units – Standard Door Installation:

Cut unit top back 95mm from front edge to allow space for

Universal Connector

Cut units for Single Rail Profile as

shown.

Guide for Fitting Handle-less Rail

Step 2

Square or Radius

Cut. R.6mm

257

257

Step 1

Note: All Layouts Shown Use Standard Clic Box Drilling Patterns

REF: 230518

Drill units for Profile Connectors using 2mm drill bit.

*Note: Careful consideration should be given to the planning and installation of built-in under appliances.

It is advisable to check appliance manufacturers’ technical specifications and set the height of the base

units accordingly.

Some built-in under appliances are not suitable for handle-less rail installations.

Base Units – drawer Installation:

Step 3

Step 4 Step 5

Cut Single Rail Profile

to size and Snap-On to

Profile Connectors.

Step 6

If External Plant-On Gables are

not being used – Use Single Rail

External Caps.

Secure Profile Connectors

to pre-drilled holes using

30mm screws.

Step 1

Step 2

Cut units for Single &

Double Rail Profiles

as shown.

Drill units for Profile

Connectors using

2mm drill bit.

Square or Radius

Cut. R. 6mm

Square or Radius

Cut. R. 6mm

Note: All Layouts Shown Use Standard Clic Box Drilling Patterns

REF: 230518

Base Corner Units Installation:

Step 3

Step 4 Step 5

Secure Profile

Connectors to pre-

drilled holes using

30mm screws.

Cut Single & Double Rail Profiles to

size and Snap-On to the Profile

Connectors.

If External Plant-On Gables are not

being used – Use Single & Double Rail

External Caps.

Step 1 Step 2

Cut & Drill gables

of Corner Unit

the same as a

Standard Door

Installation.

Mitre cut Rail

Profiles at

corner and use

the Single Rail

90° Internal

Corner

Connector to

fix together.

Note: All Layouts Shown Use Standard Clic Box Drilling Patterns

REF: 230518

Island Installation:

Tall/Vertical Unit Installation:

The Single & Double Rail Profiles may be

returned at the ends of a base unit or on an

Island Installation.

For Returns – Mitre cut Rail Profiles at the

end of the unit gables and use 90° External

Corner Connector to fix together. C or G

Gables are recommended for this kind of

installation pending on desired finish.

Step 1

Gables

Tall/Vertical Plan View

Back

17m

m

Cut front of carcass

gables back 17mm.

Step 2 Drill units for Profile Connectors.

Note: All Layouts Shown Use Standard Clic Box Drilling Patterns

REF: 230518

Step 3

Step 4

Step 5

Secure Profile Connectors to pre-drilled holes using

17mm screws.

Connect units by joining Profile

Connectors together.

Cut Rail Profiles to the overall height of the units

and Snap-On to Profile Connectors.

NOTE:

Recommended to

secure Tall units

together with

bracket on Top.

(not supplied)

Note: All Layouts Shown Use Standard Clic Box Drilling Patterns

REF: 230518

Wall Unit Installation:

*Note: Lengthen Plant-on Gables by 48mm to finish them flush with bottom of Profile Rail.

Components List:

Step 1 Step 2

Drill and secure Profile Connectors as

shown.

Cut Single Rail Profile to exact width of unit and

Snap-On to Profile Connectors.

Double Rail Single Rail

Door Height = Carcase Height + 16mm

Hinge Drillings - Door Drillings for Standard Wall

Unit with 100mm Drillings (Includes Clic Box)

• Door Top Hinge = 98mm

• Door Bottom Hinge = 116mm