gtstar 4g gps tracker user manual-zx
TRANSCRIPT
GTSTAR NEW 4G TRACKER USER MANUAL (ZX)
Preface
Content
3G:WCDMA:B1/B5/B82G:900/1800 MHz
±0.1ppm
-159dBm5--10m
Cold status 35-80sWarm status 35s
Hot status 1s
Spreadtrum SC9820ES
Build-in 3.7V Voltage Polymer battery-40°C to +85°C-20°C to +55°C
5%--95% non-condensing
Network
Frequency errorGPS chipGPS sensitivityGPS accuracy
Time To First Fix
BatteryStorage TempOperation TempHumidity
Specs4G: FDD-LTE:B1 B2 B3 B4 B5 B7 B8 B12(17) B20 B28
TDD-LTE: B38 B39 B40 B41
1.Summary
4.Usage
5.Battery And Charger
2. Applications
3. Hardware Description
Thank you for purchasing the tracker. This manual shows how to operate the devicesmoothly and correctly. Make sure to read this manual carefully before using thisproduct. Please note that specification and information are subject to changes withoutprior notice in this manual. Any change will be integrated in the latest release. Themanufacturer assumes no responsibility for any errors or omissions in this document.
Working Based on existing 4G/3G/2G (4G Version FDD-LTE/TDD-LTE) network andGPS satellites, this product can locate and monitor any remote targets by SMS orinternet. The most advanced technology of GPS and AGPS dual positioning.
Green LED for Network working status
Blue LED for GPS working status
Status of indicator
Status of indicator MeaningGPS location successfulSearching GPS signalDevice fault or dormant
MeaningCharging Low batteryFull battery or charged full
Blue led off
Status of indicator Red led on all the timeRed led flashRed led off
Slow flash (flash 1s after every 2s)Continuously in bright status
Meaning
No Network signalDevice fault or dormant
Continuously in bright statusGSM/GPRS(WCDMA)conversation start
Green Led off
Slow flash (flash 1s after every 2s)
• Vehicle rental / Fleet management etc• Outdoor sports• Protect child / the elder/ the disabled / pet etc• Provide peace-of-mind for businessmen• Personnel Management • Criminals Tracking
• Please charge 12hours at first use. • Insert SIM card in right way. Please put the unit outside and make sure the trademark side facing up.• Confirm your SIM card have calling, send SMS function.• Confirm your SIM card have enough balance (money).• Confirm your SIM card can show caller ID and don not use call forwarding function.
Do charge the battery to capacity in 8 -12 hours for first time. Please use the batteryand charger provided by the manufacturer. This unit adopts built-in Li-ion battery.
Cautions:a: For it’s Polymer battery, which contains harmful chemicals and may burst, please don’t bump, puncture it violently and keep it off fire.b: Please charge the battery in time to keep it working normally.
6.Startup Steps• Put the SIM card and battery in place.• Turn on the unit outdoors by pressing the “On/Off” button until the indicator is on. (some of model just need to insert the sim card, it willbe turn on by itself).• For first use, please initialize the unit and restore it to default setting. • In 10 or 40 seconds, the unit will begin to work and acquire the GSM signals as well as the GPS signals. The indicator will keep flashing every 3 seconds when the unit has received the signals.• When this unit receives GPS signals normally, you can use it and do any setting as the instructions of this manual.
- 1 - - 2 -
Red LED for GPS working status
A: Set admin number,by sending a SMS command to the SIM card inside device. For example: admin123456 +86186*********(+86186********should be your phone number) B: Set APN: APN123456 CMNET (please use your local APN instead of CMNET,if you do not know the APN content,you should contact your SIM card supplier)
8. Tracking Server
Platform : www.zg666gps.com
Select “Log in by ID” on the bottom of
screen IMEI No. : on the back side of
cover Password: 123456
9. Cautions
10. Faults & The solutions
Please comply with the instructions to extend the unit life: 1. Keep the unit dry. Any liquid, i.e. rain, moisture, may destroy or damage the inside circuitry.2. Don’t use & store the unit in dusty places.3. Don’t put the unit in overheated or overcooled places.4. Handle carefully. Don’t vibrate or shake it violently.5. Clear the unit with a piece of dry cloth. Don’t clean in chemicals, detergent.6. Don’t paint the unit, this may cause some foreign materials left in between the parts.7. Don’t disassemble or refit the unit.8. Please use the battery and charger provided by manufacturer. Using other batteries and chargers will cause unwanted situation.
Faults
Startup Fail
Hang up Fail
Monitoring failure
No Network Signal
SolutionCheck the battery and see if it is fully charged or correctly installed.
Please check the authorization number is set to the correct time
Please make sure SIM Card is GSM/GPRS Network and installed correctly; also call display should be on; but no call transfer and PIN code off.
Hang up Fail In existence of an authorized number, anunauthorized number dials up the unit. Please initialize the unitand re-set up the authorized numbers.
8.1 Application For Android/IOS
Download Phone APP:
Scan the QR code to download;
- 3 - - 4 -
7. SMS Command
SFunction Instruction format Reply Delete Example
Admin No. admin123456+blank+No. admin ok admin123456 0 admin123456 18188629875
APNapn+123456+blank+content
apn123456,content,username,password
apn ok apn123456 cmnet
GPRS on gprson123456,1gprs keep on set
ok,1gprson123456,1
Time zone timezone+123456+blank+GMT No. time ok timezone123456 8
SOS Sos,No.1,No.2SOS!
S1:No.1,S2:No.2
Vibrationsleep(default)
sleep123456+blank+shock sleep shock ok sleep123456 shock
No sleep sleep123456+blank+off sleep off ok sleep123456 off
Uploadfrquency
upload123456+blank+time upload ok upload123456 30
Vibrationsensitivity
vibxyz123456,3,3,3,3vibxyz:t=3,x=3,y
=3,z=3vibxyz123456,3,3,3,3
Monitor JT
Parameterquery
param1
param2
status
Vibrationalert
vibx,yOK! VibrationTime:3S Alarm
mode:Call&SMSvib3,3
Move alert move300OK! Movealarm: on
move300
Over-speedalert
speed123456+blank+speed speed ok speed123456 080
Google link g123456
Restart rstThe tracker will
immediatelyrestart!
Reset format
Firmwareupdate
checkupdateupdate
success!(noupdate)
Note: Please notice the format of command
Status