>>>tech hot licks exhaust hot licks exhaust

of 3/3
94 - MARCH 2012 - URBANBAGGER.COM URBANBAGGER.COM - MARCH 2012 - 95 >>>TECH HOT LICKS EXHAUST Reinstall the exhaust system onto the bike. Loosen and remove the footboard mounting hardware. 6 Tighten the spark plug. 15 Remove the rear exhaust mounting hardware. 9 Drill a hole through the center punch mark. 12 Remove the footboard. 7 16 Unplug the oxygen sensor. 10 Tap the exhaust pipe for the spark plug. 13 Loosen the exhaust flange nuts. 8 Install the exhaust flange nuts. 17 Remove the exhaust system from the bike. 11 Thread the spark plug into the exhaust pipe. 14 Hot Licks Exhaust Flame Thrower Kit for single pipe. Mark the exhaust 8 to 10 inches from the tip. Remove the right-side saddlebag and set it aside. 3 This ’06 Softail Bagger is getting the flame thrower treatment. BEFORE 4 Remove the seat to access the wiring. 1 Center punch the exhaust pipe. 5 Disconnect the saddlebag lighting harness. 2 Hot Licks Exhaust’s Flame Thrower Kit comes with everything you need to install the kit and shoot flames out of your ex- haust pipe(s). So how does it work? When the momentary switch is depressed it transfers the power from the ignition coil to the Hot Licks module. The interrupted power to the coil will allow un-burnt gas to flow through the exhaust pipe and ignite when it passes the installed spark plug. Hot Licks’ Flame Thrower Kits are de- signed with solid state electronic circuitry and they’re covered by a lifetime warranty. If you need a setup for duals or 2-into-1 pipes, Hot Licks offers it. Story by Nate Kersjes Photos by Jesse B. Nelson HOT LICKS EXHAUST Flame Thrower Kit

Post on 18-Mar-2022

12 views

Category:

Documents

1 download

Embed Size (px)

TRANSCRIPT

>>>TECH HOT LICKS EXHAUST
6
9
12
13
8
17
11
14
Mark the exhaust 8 to 10 inches from the tip.
Remove the right-side saddlebag and set it aside.
3
This ’06 Softail Bagger is getting the flame thrower treatment.
BEFORE
4
1
5
2
Hot Licks Exhaust’s Flame Thrower Kit comes with everything you need to install the kit and shoot flames out of your ex- haust pipe(s). So how does it work? When the momentary switch is depressed it transfers the power from the ignition coil to the Hot Licks module. The interrupted power to the coil will allow un-burnt gas to flow through the exhaust pipe and ignite when it passes the installed spark plug. Hot Licks’ Flame Thrower Kits are de- signed with solid state electronic circuitry and they’re covered by a lifetime warranty. If you need a setup for duals or 2-into-1 pipes, Hot Licks offers it.
Story by Nate Kersjes Photos by Jesse B. Nelson
HOT LICKS EXHAUST Flame Thrower Kit
96 - MARCH 2012 - URBANBAGGER.COM URBANBAGGER.COM - MARCH 2012 - 97
>>>TECH HOT LICKS EXHAUST
30
Crimp a ring terminal onto the ground wire from the Hot Licks module.
39
33
31
40
34
37
Crimp the ring terminal onto the other end of the plug wire.
32
Route the module’s power wire to the switch location.
41
35
38
Route the plug wire through the bag, to the module.
Install and tighten the rear mounting hardware.
18
Drill a hole in the bag for the spark plug wire.
27
21
Route the wires through the grommet that the lighting wires pass through.
24
19
28
Extend the wiring the necessary amount for the Hot Licks module.
22
25
20
29
23
26
>>>TECH HOT LICKS EXHAUST
Disconnect the ignition coil wiring.
42
Terminal (A) is the coil side of the wire from step 44, (B) is where the Hot Licks module connects, and (C) is the power side of the wire from step 44.
51
45
These two wires will provide power to the coil. When the button is pushed the power will divert from the ignition coil to the Hot Licks module.
48
Test for battery voltage with the key in the “on” position.
43
52
46
49
Cut the wire that provides 12 volts to the coil. The flame thrower switch will complete the connection in the end.
44
53
47
50
Plug the spark plug cables into the ignition coil. Install the seat and mounting hardware.
54 55
With a twist of the throttle and push of the button, this bike is spitting fire.
AFTER HOT LICKS EXHAUST Flame Thrower Kit - Single Exhaust
850.473.0465 www.hotlicksexhaust.com