grundfos catalogue industry and water utility eng 2014

Industry and WaterUtility Catalogue

2014

Grundfos product information

1.General information, pump technology

1.1 Catalogue content (WinCAPS, WebCAPS)

1.2 General pump technology data (Pump curves, interpretation, validity, minimum inlet pressure and. calculation of the inlet pressure, manufacturing standards, certifications, ATEX, etc.)

2. Centrifugal pumps for general applications

Single stage centrifugal pumps 2.1 Single-stage end-suction pumps EN 733 NB/NBE, NK/NKE

ISO 2858 NBG/NBGE, NKG/NKGE

2.2 Horizontal split case pumps HS

Multistage centrifugal pumps2.3 Submersible pumps SP A, SP A-N, SP, SP-N, SPG

2.4 Environmental pumps MP1, SQ-NE, SP A-NE, SP-NE

2.5 Horizontal pumps CM, CME

2.6 Vertical pumps CR, CRI, CRN, CRE, CRIE, CRNE

Pressure booster systems2.7 Pressure booster systems Overview Pressure booster sets Hydro Multi-E Hydro MPC

3.Pumps for special industrial applications

Custom built pumps3.1 Single-stage end-suction pumps EN 733 NB/NBE, NK/NKE


3.2 Custom built CR pumps (high temperature, CR, CRI, CRN, CRT, CRN-SF high pressure demand, agressive liquids, etc.) CRE, CRIE, CRNE, CRTE, CRNE-HS

High pressure equipment3.3 High pressure booster modules with submersible pumps BM, BMB

3.4 High pressure booster modules with external drive BME, BMET

3.5 High pressure piston pumps BMP, BMPE

Coolant and lubricant pumps3.6 Single- and multistage immersible pumps MTR, MTRE, SPK, SPKE, MTH, MTA

3.7 Screw pumps MTS

3.8 Single-stage centrifugal pumps with semi-open impellers

MTB

Table of contents

Grundfos product information

1.General information, pump technology

1.1 Catalogue content (WinCAPS, WebCAPS)

1.2 General pump technology data (Pump curves, interpretation, validity, minimum inlet pressure and. calculation of the inlet pressure, manufacturing standards, certifications, ATEX, etc.)

2. Centrifugal pumps for general applications

Single stage centrifugal pumps 2.1 Single-stage end-suction pumps EN 733 NB/NBE, NK/NKE


2.2 Horizontal split case pumps HS

Multistage centrifugal pumps2.3 Submersible pumps SP A, SP A-N, SP, SP-N, SPG

2.4 Environmental pumps MP1, SQ-NE, SP A-NE, SP-NE

2.5 Horizontal pumps CM, CME

2.6 Vertical pumps CR, CRI, CRN, CRE, CRIE, CRNE

Pressure booster systems2.7 Pressure booster systems Overview Pressure booster sets Hydro Multi-E Hydro MPC

3.Pumps for special industrial applications

Custom built pumps3.1 Single-stage end-suction pumps EN 733 NB/NBE, NK/NKE


3.2 Custom built CR pumps (high temperature, CR, CRI, CRN, CRT, CRN-SF high pressure demand, agressive liquids, etc.) CRE, CRIE, CRNE, CRTE, CRNE-HS

High pressure equipment3.3 High pressure booster modules with submersible pumps BM, BMB

3.4 High pressure booster modules with external drive BME, BMET

3.5 High pressure piston pumps BMP, BMPE

Coolant and lubricant pumps3.6 Single- and multistage immersible pumps MTR, MTRE, SPK, SPKE, MTH, MTA

3.7 Screw pumps MTS

3.8 Single-stage centrifugal pumps with semi-open impellers

MTB

Table of contents

Refrigerant circulation pumps3.9 Multistage centrifugal pumps with a

canned-motor RC

Sanitary pumps3.10 Single- and multi-stage, end-suction centrifugal pumps Euro-HYGIA, F&B-HYGIA, Contra, durietta

3.11 Single-stage, self-priming, side-channel pumps SIPLA

3.12 Single-stage, end-suction centrifugal pumps MAXA, MAXANA

3.13 Rotary lobe, positive displacement pumps NOVAlobe

4.Wastewater and sewage pumps

Wastewater pumps4.1 Submersible drainage and euent pumps Unilift CC/KP/AP/AP-B, DP10, EF30, SL1.50, SLV.65

4.2 Dewatering pumps DW, DWK, DPK

4.3 Self-priming wastewater pumps Pomona (portable or built-in)

Sewage pumps4.4 Grinder sewage pumps SEG

4.5 Sewage pumps - SE/SL, and S series Overview Sewage pumps 1,1-11 KW SE/SL

4.6 Sewage pumps 9-30 KW SE/SL

4.7 High performance sewage pumps, S Grundfos well bottom SMART Bottom

4.8 Axial flow pumps with channel impeller ST

4.9 High performance axial and mixed flow pumps with propeller impeller KPL with channel impeller KWM

5.Wastewater treatment equipment

Mixers and flowmakers5.1 Mixers, flowmakers AMD, AMG, AFG

Recirculation pumps5.2 Submersible recirculation pumps SRP

Aeration equipment5.3 Aeration equipment AeroJet V, Diusers

6.Control and pump protection equipment

Monitoring and control6.1 Grundfos remote control system GRM

(Grundfos Remote Management)

6.2 Communication interface units CIM, CIU

6.3 Local communication devices R 100, PC Tool

Multi-purpose control equipment6.4 Control cabinets Control MPC

6.5 Frequency converters CUE

6.6 Pump monitoring equipment CR/CRE-Monitor

6.7 Dry-running protection LiqTec

6.8 Motor protection and monitoring MP 204, IO 112

6.9 One pump control cabinet Control MP 204

6.10 Transmitters, sensors, additional electric units

Wastewater pumps control equipment6.11 Control cabinets for 1-6 pumps DC

6.12 Control cabinets for 1-2 pumps LC/LCD 108

6.13 Control units for 1 pump CU 100

6.14 Motor protection module IO 111

6.15 Sensor module SM 111

6.16 Transmitters, sensors, flow switches

7.Dosing applications

Dosing pumps7.1 New, digital diaphragm pumps DDA, DDC, DDE

7.2 Digital diaphragm pumps DDI, DME

7.3 Mechanical/hydromechanical diaphragm pumps DMX, DMH

7.4 Dosing pump accessories

Measurement and control technology7.5 Water parameter measuring-controlling instruments ConexDIA-1/-2/-2Q, ConexDIS-PR/-D

and accessories DIP, ConexDIS-C

7.6 Hand-held photometers DIT-M, DIT-L

7.7 Gas leak detection system ConexDIA-G, ConexDIS-G

Disinfection7.8 Vacuum chlorine gas dosing systems Vaccuperm

7.9 Electrolytic chlorination systems Selcoperm

7.10 Chlorine dioxide generation systems Oxiperm

Preparation of chemicals7.11 Powder handling and dosing

systems Polydos, KD

Grundfosproduct description

1Grundfos product description

lsd ezen katalgus XX. rszt

www.grundfos.com WebCAPS





Technical dataFlow Q: max. 3,2 m3/hHead H: max. 6 mLiquid temperature: +2 C +110 CSystem pressure: max. 10 bar

ApplicationsHot and cold water circulation, hot watercirculation systems, heat systems, coolingand air conditioning systems.

Features and benefits requires no maintenance low noise, low power consumption, a wide range of products.

Options AUTOADAPT self-learning mode, automatic power control, easy to mount - outdoor electricconnection,

three speed levels.

Technical dataFlow Q: max. 10 m3/hHead H: max. 8 mLiquid temperature: -25 C +110 CSystem pressure: max. 10 bar

ApplicationsHot and cold water circulation,hot water circulating systems.

Features and benefits requires no maintenance low noise, low power consumption, a wide range of products, stainless steel, brass or bronze housing.

Options 24-hour time switch thermostat


ApplicationsHot and cold water circulation in residentialbuildings, public institutions, in heating-,cooling- and hot water systems of commercialestablishments, district heating systems.

Features and benefits AUTOADAPT self-learning mode, automatic power control, low noise, low power consumption, a wide range of products, easy to mount - no additional equipmentneeded,

safe selection.

Options stainless steel, twin pump Grundfos GO (see above) orR 100 remote control

GENIbus, LONbus communication.

MAGNA, MAGNA3 seriesElectronically controlled,wet-rotor circulator pumps

COMFORTUP-N, N-UPS 100 Series

Wet-rotor, hot water circulator pumps.

ALPHA2, Electronically controlled,wet-rotor circulator pumps

H [m]

1 4 8 15 20 30 601,5

2

34

15

5

12

18

Q[m3/h]00.4 11 2 4 6 1010 15

Q[ m/h]

0.20.2

0.4

1.01.0

2.0

4.06.0

10.010.0H[ m]

ALPHA2

00.1 0.2 0.5 11 2 4 6 1010Q [m/h]

0.1

0.2

0.4

1.01.0

2.0

4.0

8.0H [m]

UP-N, UPS-N Series 100

COMFORT







Technical dataFlow Q: max. 370 m3/hHead H: max. 90mLiquid temperature: -25 C +140 CSystem pressure: max. 16 bar

ApplicationsHot and cold water circulation in heatingsystems, hot water circulation systems,cooling and air conditioning systems.

Features and benefits low power consumption, existing systems can be connected, easy installation.

Options parallel operation R 100 infrared remote control GENIbus, LONbus communication twin pump.

Technical dataFlow Q: max. 4 600 m3/hHead H: max. 170 mLiquid temperature: -25 C +140 CSystem pressure: max. 25 bar

ApplicationsHot and cold water circulation in heatingsystems, district heating systems, domestichot water systems, cooling and airconditioning systems.

Features and benefits compact design, a wide range of products, standard motor easy to maintain, various types of shaft seals dependingon liquid, temperature, and pressure

Options bronze housing, twin pump.

TPE Series 2000Electronically controlled,close coupled in-line circulators

TPClose coupled in-line circulators




Options many control options R 100 infrared remote control GENIbus, LONbus communication.


2 4 10 20 40 100 200 400Q [m/h]

2

4

10

20

40

100H [m]

10 40 100200400 1000 4000Q [m/h]

5

1010

20

50

100100

200H [m]

2 4 10 20 40 100 200 400Q [m/h]

2

4

10

20

40

100H [m]








Technical dataFlow Q: max. 370 m3/hHead H: max. 90mLiquid temperature: -25 C +140 CSystem pressure: max. 16 bar



Options parallel operation R 100 infrared remote control GENIbus, LONbus communication twin pump.

Technical dataFlow Q: max. 4 600 m3/hHead H: max. 170 mLiquid temperature: -25 C +140 CSystem pressure: max. 25 bar

ApplicationsHot and cold water circulation in heatingsystems, district heating systems, domestichot water systems, cooling and airconditioning systems.

Features and benefits compact design, a wide range of products, standard motor easy to maintain, various types of shaft seals dependingon liquid, temperature, and pressure

Options bronze housing, twin pump.


TPClose coupled in-line circulators




Options many control options R 100 infrared remote control GENIbus, LONbus communication.


2 4 10 20 40 100 200 400Q [m/h]

2

4

10

20

40

100H [m]

10 40 100200400 1000 4000Q [m/h]

5

1010

20

50

100100

200H [m]

2 4 10 20 40 100 200 400Q [m/h]

2

4

10

20

40

100H [m]









ApplicationsLiquid transfer in district heating systems,water supply systems, cooling and airconditioning systems, industry, fireprotection systems.

Features and benefits dimensions according to ISO andEN standards

a wide range of products, robust design, applicability in heavy operatingconditions,

wide range of motors.

NK, NKGSingle stage end-suction pumps accordingto EN 733 and ISO 2858


ApplicationsLiquid transfer in district heating systems,residential heating systems, cooling andair conditioning systems, washing systems,industry.

Features and benefits dimensions according to ISO andEN standards

a wide range of products, compact design, broad applicability, standard motor Shaft seal according to EN 12 756.

Options various types of shaft seals dependingon liquid, temperature, and pressure,

cast iron or bronze impeller.


ApplicationsLiquid transfer in district heating systems,residential heating systems, cooling andair conditioning systems, washing systems,industry.

Features and benefits dimensions according to EN standards compact design, a wide range of applications, shaft seal according to EN 12 756, built-in inverter anddigital controller

a number of regulatory options.


cast iron or bronze impeller infrared wireless communication withR 100 remote control.

NBE, NBGEElectronically-controlled, single-stageend-suction pumps according to EN 733and ISO 2858

NB, NBGSingle-stage end-suction pumps according to EN 733 and ISO 2858

4 10 20 50 100 200 500Q [m/h]

610

20

50

100

200H [m]

10004 10 20 40 60 100 200 500Q [m/h]

46

10

20

4060100

H [m]

4 10 20 50 100 200 500Q [m/h]

610

20

50

100

200H [m]

1000








Technical dataFlow Q: max. 2 500 m3/hHead H: max. 148 mLiquid temperature: 0 C +100 CSystem pressure: max. 16 bar

ApplicationsWater supply, pressure boosting, districtheating, air treatment systems, coolingsystems, power plant systems, fireprotection systems.

Features and benefits flanges according to EN 1092-2 (DIN 2501) robust design, double-suction volute design a wide range of products, standard electric motors, unique design options according touser needs

shaft seal according to EN 12756

Options ductile iron and steel housing gland packing, bronze, aluminum and stainless steelimpeller.


ApplicationsWash down systems, water transfersystems, district heating systems, coolingand air conditioning systems, industry.

Features and benefits dimensions according to DIN standards a wide range of products, robust design, applicability in heavy operatingconditions,

wide range of motors, a number of regulatory options R100 infrared remote control.


cast iron or bronze impeller, infrared wireless communication withR 100 remote control.

HSHorizontal split case, single-stage,non-self-priming, centrifugal volute pumps

NKE, NKGEElectronically-controlled, single-stageend-suction pumps according to EN 733and ISO 2858


ApplicationsWater transfer systems, cooling and airconditioning systems, water supplysystems, water treatment plants, fireprotection systems, industry,boiler feeding- and condensate- pumps.

Features and benefits a wide range of products, reliability, in-line design, high eciency, easy to maintain, space saving, for slightly aggressive media.

Options dry-running protection and motorprotection via LiqTec

CR, CRI and CRNVertical, multistage, centrifugal pumps(CRI, CRN parts in contact with liquids,from stainless steel)

4 10 20 40 60 100 200 500Q [m/h]

46

10

20

4060100

H [m]

1 2 4 6 1010 20 40 100100200Q [m/h]

20

4060

100150200

H [m]









ApplicationsWater transfer in water treatment systems,washing systems, seawater systems, acid-and alkali- pumping, fine filter systemsreverse osmosis systems, swimming pools.

Features and benefits high degree of corrosion resistance, reliability, in-line design, high eciency, easy to maintain, space-saving.


CRTMultistage, vertical, centrifugal pumps(all parts in contact with liquids, fromtitanium)


ApplicationsWater transfer systems, water treatmentsystems, industry, boiler- and condensate-pumping.

Features and benefits a wide range of products, reliability, in-line design, high eciency, easy to maintain, space-saving, suitable for slightly aggressiveliquids



ApplicationsWater transfer systems, cooling and airconditioning systems, water supplysystems, water treatment systems, fireprotection systems, industry,boiler feeding pumps.

Features and benefits a wide range of products, reliability, in-line design, high eciency, easy to maintain, space saving.

Options R 100 infrared remote control.

CRN-SF, CRNE-HS for highpressureMultistage, vertical, centrifugal pumps (allparts in contact with liquids, from stainlesssteel)

CRE, CRIE, CRNEElectronically controlled, multistage,vertical, centrifugal pumps (CRIE, CRNE parts in contact with liquids, fromstainless steel)

2 5 10 20 50 100 200Q [m/h]

2

51020

50100200

H [m]

1 2 4 6 1010 20 40 100100 200Q [m/h]

20

4060100

200

400

H [m]







Technical data Supported pumps, CR, CRI, CRN, CRNwith MAGdrive

Motor range: 1.1 to 75 kW, EFF1 Available for pumps with standardMG/Siemens motors, MG/Siemensmotors supplied from a Grundfos CUEfrequency converter and MGE motors with integrated frequency converter

Basic layout: Control / Hydro MPC andLiqTec

Enclosure class: IP 54 Supply voltage: 3 x 400 VAC

Applications Pumps in demanding applicationswhere zero downtime is required, pumpsexposed to extreme wear or cloggingdue to materials in the pumped liquid,and in processes where continuousmonitoring and control are essential.

Features and benefits Detects if the pump eciency is reduced, Detects if the pump is about to cavitate, Detects if the pump is running outsideits normal operating range,

Enables planning of pump maintenancein order to prevent unplanned downtime.

Options 24/7 monitoring of operation andprotection of equipment,

Bus communication to SCADA systemor Web-link,

Data collection, monitoring and settingthrough local PC or via internet.

Technical dataSystem pressure: max. 16 barAmbient temperature: max. 40 CLiquid temperature: max. 40 C

ApplicationsLow power, water supply systems operatingfrom their own well, agricultural and garden irrigation equipment, water supply ofhouses, ranches.

Features and benefits Four sizes and two kinds of materialquality, one type, with all the parts incontact with water from stainless steel,

abstraction from max. 90 m depth, easy to maintain, the pump head and foot are fromgalvanized cast iron.

Options Hose kit (for simple change fromCPE/CPES to CR DW)

CR MonitorMonitoring of pump eciency, cavitationand performance

CR DWDeep well centrifugal pump


ApplicationsWater transfer systems, cooling and airconditioning systems, water supplysystems, irrigation systems, industrialand other water supply systems.

Features and benefits compact design, wide range of applications, high reliability, very low noise level.

Options for dierent liquids, suitable structuralmaterials can be selected,

variety of connection solutions, wide range of shaft seals.

CMMultistage horizontal centrifugal pumps

00,25 0,4 0,6 11 1,5 2 3Q [m/h]

20

30

40

60

80100

HD [m]

0 10 20 30Q [m/h]

0

100

20

40

6080

130H[m]








Technical data Supported pumps, CR, CRI, CRN, CRNwith MAGdrive

Motor range: 1.1 to 75 kW, EFF1 Available for pumps with standardMG/Siemens motors, MG/Siemensmotors supplied from a Grundfos CUEfrequency converter and MGE motors with integrated frequency converter

Basic layout: Control / Hydro MPC andLiqTec

Enclosure class: IP 54 Supply voltage: 3 x 400 VAC

Applications Pumps in demanding applicationswhere zero downtime is required, pumpsexposed to extreme wear or cloggingdue to materials in the pumped liquid,and in processes where continuousmonitoring and control are essential.

Features and benefits Detects if the pump eciency is reduced, Detects if the pump is about to cavitate, Detects if the pump is running outsideits normal operating range,

Enables planning of pump maintenancein order to prevent unplanned downtime.

Options 24/7 monitoring of operation andprotection of equipment,

Bus communication to SCADA systemor Web-link,

Data collection, monitoring and settingthrough local PC or via internet.

Technical dataSystem pressure: max. 16 barAmbient temperature: max. 40 CLiquid temperature: max. 40 C

ApplicationsLow power, water supply systems operatingfrom their own well, agricultural and garden irrigation equipment, water supply ofhouses, ranches.

Features and benefits Four sizes and two kinds of materialquality, one type, with all the parts incontact with water from stainless steel,

abstraction from max. 90 m depth, easy to maintain, the pump head and foot are fromgalvanized cast iron.

Options Hose kit (for simple change fromCPE/CPES to CR DW)

CR MonitorMonitoring of pump eciency, cavitationand performance

CR DWDeep well centrifugal pump


ApplicationsWater transfer systems, cooling and airconditioning systems, water supplysystems, irrigation systems, industrialand other water supply systems.

Features and benefits compact design, wide range of applications, high reliability, very low noise level.


variety of connection solutions, wide range of shaft seals.

CMMultistage horizontal centrifugal pumps

00,25 0,4 0,6 11 1,5 2 3Q [m/h]

20

30

40

60

80100

HD [m]

0 10 20 30Q [m/h]

0

100

20

40

6080

130H[m]








Technical dataFlow Q: max. 9 m3/hHead H: max. 210 mLiquid temperature: 0 C +40 CSystem pressure: max. 150 m

ApplicationsDomestic water supply systems,groundwater supply to waterworks,horticultural and agricultural irrigation,groundwater drainage, industrialapplications.

Features and benefits built-in protection against dry running, soft start, over- and undervoltage protection, high eciency.

Options SQE can be protected, monitored and controlled by the CU 300 and CU 301 unit.

SQ, SQE3" submersible pumps


ApplicationsWater transfer, pressure boosting domesticwater supply systems, cooling and airconditioning systems, irrigation systems,industrial water- and other fluid supplysystems.

Features and benefits compact design, wide range of applications, high reliability, low noise, integrated electronic motor speedregulation.


variety of connection solutions, wide range of shaft seals. infrared wireless communication R 100with remote control

control system connection throughanalog, digital in-and outputs.

Bus communication via GENIbus, orthrough LONbus, Profibus, Modbusprotocol operated networks, with thesurveillance systems.


ApplicationsPressure boosting in residential buildings,irrigation systems, cooling and airconditioning systems, small industrialsystems.

Features and benefits modular and compact design, reliability, low noise.

Options built in to complete booster systems(Hydro Pack, Hydro Dome)

CMVMultistage, vertical, centrifugal pumps

CMEElectronically-controlled, multi-stage,horizontal centrifugal pump

0 10 20 30 36Q [m/h]

100

20

0

40

60

80

120H[m]

1 2 3 4 6 8Q [m/h]

46

10

20

4060

100H [m]








Technical dataFlow Q: max. 90 m3/dayHead H: max. 200 mLiquid temperature: 0 C +40 CPower supply: 30300 VDC or

1 90240 V, 50/60 HzBuilt-in depth: max. 150 m

ApplicationsWater supply and irrigation in areaswithout electricity.

Features and benefits no need for electricity, no maintenance.

Technical dataFlow Q: max. 22 m3/hHead H: max. 215 mLiquid temperature: 0 C +40 CInstallation depth: max. 600 m

ApplicationsContaminated groundwater extraction,sampling, remediation.

Features and benefitsSQE-NE same properties as SQE,SP-NE same properties as SP.

SQ FlexRenewable-energy based water supplysystems

SQE-NE, SP-NE3" and 4" environmental submersiblepumps

Technical dataFlow Q: max. 470 m3/hHead H: max. 670 mLiquid temperature: 0 C +60 CInstallation depth: max. 600 m

ApplicationsGroundwater supply to waterworks,horticultural and agricultural irrigation,groundwater drainage, pressure boosting,industrial use.

Features and benefits high eciency, long service life as all components are of stainless steel.

Options monitoring and control, via MP 204 /R 100 unit.

SP A, SP, SP-G4", 6", 8", 10", 12" submersible pumps

0 20 40 60 80 100Q [m/nap]

0

40

80

120

160

200

240H [m]

1 2 4 1010 20 40 100100 200 600Q [m/h]

10

20

4060

100

200

400600

H [m]








Technical dataFlow Q: max. 2,4 m3/hHead H: max. 95 mLiquid temperature: 0 C +35 C

Applicationssampling.

Features and benefits compact design, fit into 50 mm boreholes.

MP 12", environment submersible pumps

Technical data6" sizes: 3,737 kW8" sizes: 22110 kW10" sizes: 75190 kW12" sizes: 147250 kW

ApplicationsThe Grundfos MMS submersible motors can be fitted on all Grundfos SP andSP-G pumps.

Features and benefits a wide range of products, easily rewound, protection against upthrust, high eciency, 6" and 8" sizes have standardized NEMAflange and shaft.

Options material variants, PA winding, SiC / SiC mechanical shaft seal

overtemperature protection via Pt100.

Technical data4" sizes: 0,37 7,5 kW6" sizes: 5,530 kW

ApplicationsThe Grundfos MS submersible motors canbe fitted on all Grundfos SP A, SP pumpsand can be used in the high- pressurebooster modules, type BM and BMB.

Features and benefits built-in TEMPCON temperaturetransmitter,

standardised NEMA flange and shaft,

completely encapsulated in stainless steel, liquid-cooled and has liquid-lubricatedbearings.

Options material variants.

MMS motorsStainless steel, 6", 8", 10" and 12",rewindable submersible motors

MS motorsStainless steel, 4" and 6" rewindablesubmersible pumps

10

Grundfos product description







Technical dataFlow Q: 6,0 m3/hHead H: up to 75 mLiquid temperature: 0 +40 CInstallation depth: up to 20 m

ApplicationsWater withdrawal and pressure boostingbuildings, irrigation facilities, water supplyfrom wells, reservoirs, cisterns, rivers, lakesand storage wells.

Features and benefits low water level operation, since themotor is permanently wetted by theliquid,

corrosion resistance due to the fullapplication of of stainless steel,

hermetically sealed cable entry, double shaft seal to ensure operatingsafety,

robust design easy installation due to built-in capacitorand motor protection.

Options design with strainer or base plate, water level control with float switch.

Technical dataFlow Q: max. 5 m3/hHead H: max. 48 mLiquid temperature: 0 C +35 CSystem pressure: max. 7,5 bar

ApplicationsRainwater collection and transfer in houses,farms, greenhouses.

Features and benefits automatic changeover betweenrain-water tank and integrated mainswater tank,

manual changeover between rainwater tank and integrated mains water tank,

acoustic/visual alarm in case of overflowin integrated mains water tank.

Options control of additional booster pump,

backflow monitoring equipment.

RMQRainwater collection system

SPOSubmersible Pumps

Technical dataFlow Q: max. 5 m3/hHead H: max. 48 mLiquid temperature: 0 C +35 CSystem pressure: max. 7,5 bar

ApplicationsWater transfer in family houses,apartments, farms and greenhouses.

Features and benefits complete booster system, easy to install, operate, self-priming, protection against dry running,with automatic restart function,

low noise, no maintenance.

MQMulti-stage self-primingcentrifugal pumps

0 1 2 3 4 5 6 7Q [m/h ]

010203040506070

H [m]

11








Technical dataFlow Q: max. 35 m3/hHead H: max. 18 mLiquid temperature: 0 C +55 CSystem pressure: max. 50 mm

ApplicationsDrainage of flooded cellars, pumping ofdomestic wastewater, groundwaterlowering emptying of swimming poolsand excavations emptying of drainwells emptying of tanks and reservoirs.

Features and benefits simple installation, service- and maintenance-free.

Options Unilift AP35B and AP50B have auto-coupling and horizontal outlet.

Unilift CC, AP, AP35B, AP50B stainless steel Wastewater and sewage pumps

Technical dataFlow Q: max. 5 m3/hHead H: max. 48 mLiquid temperature: 0 C +55 CSystem pressure: max. 6 bar


Features and benefits self-priming, stable operation in case of air bubbleappearance.

Demand Automatic start / stop modePress Control Control Unit,

Low Power (Private) booster sets.

Technical dataSupply voltage: 1230 V, 50 Hz 10%Maximum switchingcurrent: PM 1: 6 A PM 2: 10 AMax outputpower:

PM 1: 1200 W

PM 2: 2000 WConsumption(own):

1 W

Enclosure class: IP 65Liquid temperature: 0 +40 CCut-in pressure: PM 1: 1,5 and 2,2 bar PM 2: 15 bar System pressure: 10 bar

ApplicationsWater supply and pressure boosting pumpsystems with automatic On / O switching,houses, cottages, park and gardenirrigation systems.

Features and benefits easy mounting because of the freelyselectable mounting position andadjustable discharge port,

safety: protection against dry runningand protection against switching,

comfort: - adjustable cut-in pressure(2 PM)

- Optional restart modes(2 PM)

- Swivel front panel (2 PM)

PM 1, PM 2Pressure Manager

JPSelf-priming jet pumps

12








Technical dataFlow Q: max. 35 m3/hHead H: max. 18 mLiquid temperature: 0 C +55 CSystem pressure: max. 50 mm

ApplicationsDrainage of flooded cellars, pumping ofdomestic wastewater, groundwaterlowering emptying of swimming poolsand excavations emptying of drainwells emptying of tanks and reservoirs.

Features and benefits simple installation, service- and maintenance-free.

Options Unilift AP35B and AP50B have auto-coupling and horizontal outlet.

Unilift CC, AP, AP35B, AP50B stainless steel Wastewater and sewage pumps



Features and benefits self-priming, stable operation in case of air bubbleappearance.

Demand Automatic start / stop modePress Control Control Unit,

Low Power (Private) booster sets.

Technical dataSupply voltage: 1230 V, 50 Hz 10%Maximum switchingcurrent: PM 1: 6 A PM 2: 10 AMax outputpower:

PM 1: 1200 W

PM 2: 2000 WConsumption(own):

1 W

Enclosure class: IP 65Liquid temperature: 0 +40 CCut-in pressure: PM 1: 1,5 and 2,2 bar PM 2: 15 bar System pressure: 10 bar

ApplicationsWater supply and pressure boosting pumpsystems with automatic On / O switching,houses, cottages, park and gardenirrigation systems.

Features and benefits easy mounting because of the freelyselectable mounting position andadjustable discharge port,

safety: protection against dry runningand protection against switching,

comfort: - adjustable cut-in pressure(2 PM)

- Optional restart modes(2 PM)

- Swivel front panel (2 PM)

PM 1, PM 2Pressure Manager

JPSelf-priming jet pumps







Technical dataFlow Q: max. 88 l/s (315 m3/h)Head H: max. 45 mLiquid temperature: 0 C +40 CDischarge: DN 65 DN 150

ApplicationsThe pumps are suitable for wastewater,industrial wastewater, raw water, waterwith dirt pieces.

Features and benefits S- tube, single channel closed orSuperVortex impeller,

free passage up to 100 mm, low clogging danger, low operating costs, motor cooling without coolant, double cartridge mechanical seal, cable plug connection, modularity.

Options control and protection systems, motor operation control.

Technical dataFlow Q: max. 19,5 l/s (70 m3/h)Head H: max. 25 mLiquid temperature: 0 C +40 CDischarge: Rp 2 DN 65

ApplicationsSuitable for drainage, euent, processwater, wastewater transfer.

Features and benefits cable plug connection, a single channel or Vortex impeller, solids passage up to65 mm,

cartridge shaft seal system, modularity.

Options control and protection systems, motor operation control.

SE / SL from 1.1 to 11 kWWastewater pumps

DP, EF, SL1, SLVWastewater and sewage pumps

Technical dataFlow Q: max. 5 l/s

(max. 18 m3/h)Head H: max. 47 mLiquid temperature: 0 C +40 C

ApplicationsPumping of wastewater with toilet wastethrough pipes small cross-section pipes.

Features and benefits a wide range of products, no maintenance, a wide range of applications.

Options wide range of accessories pump control and motor control andlevel control equipment.

SEGSewage grinder pumps

1 2 3 5 7 1 0 1 0 3 0 Q [ l / s ]

1

2

4 6 1 0 1 0

2 0

H [ m ]

5 10 15 20 30 40 60 100Q [l/s]

2346

10

203040

H [m]

13









(max. 1000 m3/h)Head H: max. 70 mLiquid temperature: see p. of 4.6-3.

sidewaysFree flow-size: max. 160 mm

ApplicationsWastewater (leachate, stormwater)containing solids, fibrous materials,faecal sewage, corrosive and / or aggressiveindustrial wastewater, industrial coolingand process water transfer.


IE3 eciency class motors, H (180 C) insulation class motorwindings,

very high eciency, wide range, SmartTrim system installation on foot or auto-coupling, operation with or without cooling jacket, wet or dry well installation, double cartridge mechanical seal, built-in motor protection sensors.

Options control and protection systems.


(7 200 m3/h)Head H: max. 120 mLiquid temperature: see p. of 4.6-3.


ApplicationsLarge amounts of raw or treated municipaland industrial wastewater, corrosive liquids,drink water lifting and transfer.

Features and benefits wide range, SmartTrim system installation on foot or auto-coupling, operation with or without cooling jacket, wet or dry well installation, various impeller types, built-in motor protection sensors.


Technical dataFlow Q: max. 700 m3/minHead H: max. 20 mLiquid temperature: 0 C +40 C

ApplicationsThe pumps are specifically designed forpumping sewage and wastewater in awide range of municipal and industrialapplications, they are used in flood andstormwater control, drainage/irrigationof large quantities of water, raw-waterintake, transfer of liquids in large-scalemunicipal sewage treatment plants,circulation of large quantities of water inwater theme parks,etc.

Features and benefits high water transfer capacity, robust design, low maintenancerequired,

adaptable mountingoptions,

built-in motor protection units, large free passage cross section, high eciency over the entire life span.

Options explosion-proof (ST) special shaft seals, motor control units.

ST, KPL, KWMAxial and mixed flow pumps

SE/SL 930 kWWastewater pumps

S SeriesHigh performance wastewater pumps

0 20 60 100 200 280Q [l/s]

3

5

101520

406080

H [m]

10 20 40 100 200 400 1000 3000Q [l/s]

4610

20

4060100

H [m]

00 10 20 40 100 200 700

3457

10

1520

30H [m]

Q [m3/min]

14









(max. 1000 m3/h)Head H: max. 70 mLiquid temperature: see p. of 4.6-3.


ApplicationsWastewater (leachate, stormwater)containing solids, fibrous materials,faecal sewage, corrosive and / or aggressiveindustrial wastewater, industrial coolingand process water transfer.


IE3 eciency class motors, H (180 C) insulation class motorwindings,

very high eciency, wide range, SmartTrim system installation on foot or auto-coupling, operation with or without cooling jacket, wet or dry well installation, double cartridge mechanical seal, built-in motor protection sensors.



(7 200 m3/h)Head H: max. 120 mLiquid temperature: see p. of 4.6-3.


ApplicationsLarge amounts of raw or treated municipaland industrial wastewater, corrosive liquids,drink water lifting and transfer.

Features and benefits wide range, SmartTrim system installation on foot or auto-coupling, operation with or without cooling jacket, wet or dry well installation, various impeller types, built-in motor protection sensors.


Technical dataFlow Q: max. 700 m3/minHead H: max. 20 mLiquid temperature: 0 C +40 C

ApplicationsThe pumps are specifically designed forpumping sewage and wastewater in awide range of municipal and industrialapplications, they are used in flood andstormwater control, drainage/irrigationof large quantities of water, raw-waterintake, transfer of liquids in large-scalemunicipal sewage treatment plants,circulation of large quantities of water inwater theme parks,etc.

Features and benefits high water transfer capacity, robust design, low maintenancerequired,

adaptable mountingoptions,

built-in motor protection units, large free passage cross section, high eciency over the entire life span.

Options explosion-proof (ST) special shaft seals, motor control units.

ST, KPL, KWMAxial and mixed flow pumps

SE/SL 930 kWWastewater pumps

S SeriesHigh performance wastewater pumps

0 20 60 100 200 280Q [l/s]

3

5

101520

406080

H [m]

10 20 40 100 200 400 1000 3000Q [l/s]

4610

20

4060100

H [m]

00 10 20 40 100 200 700

3457

10

1520

30H [m]

Q [m3/min]







Technical dataSupply voltage: 1230, 3230 and

3400 V, 50/60 Hz

ApplicationsDedicated controls are suitable in wastewaterapplications for emptying wastewater pits (upto six pumps), they are used in pressurisedpumping stations,network pumping stations,commercial buildings.

Features and benefits automatic energy optimization easy installation and configuration configuration wizard electrical overview advanced data communication advanced alarm and warning priority supports several languages daily emptying mixer control or flush valve user-defined functions anti-blocking start level variation advanced pump alternation withpump groups

SMS scheduling communication to SCADA, BMS, GRM or cell phone.

Options control panel for direct, star-delta orsoft start,

UPS battery supply, IO 111 motor protection and SM 111 sensormodule.

Dedicated ControlsControl Cabinets 1-6for wastewater pumps

LC, LCD 107, 108 and 110Pump controllers with pneumatic signal,float switch or electrodes


3400 V, 50/60 Hz

ApplicationsPumping stations, filling/emptying of tanks.

Features and benefits control of one (LC) or two pumps (LCD) automatic alternating operation (LCD) automatic test run preventing shaft sealsfrom seizing up during long periods ofinactivity

water hammer protection starting delay after power failure stop delays automatic alarm reset (if required) automatic restart (if required) liquid level indication high-level alarm motor overload protection relay protection against motor overheatingvia input from PTC resistor/thermalswitch.

Options SMS modem with built-in hour and startcounter (information on mobile phone)

hour counter start counter signal lamp acoustic signal external mains switch.


3400 V, 50 Hz.

ApplicationsThe control unit CU 100 is designed forthe starting, operation and protection ofsmall pumps.The control unit is suitable for the followingoperating currents: single-phase: up to 9 A. three-phase: up to 5 A

Features and benefits control of one pump start/stop by means of a float switch or manual start/stop.

several variants for single- and three-phase pumps

single-phase control units are supplied with capacitors and with or without float switch.

three-phase control units are supplied with a float switch

IP 54 enclosure, threaded cableglands.

CU100Control unit for a wastewatersewage pump

15









Applications dewatering construction sites, groundwater water level control, park and garden watering, water supply in horticulture andagriculture,

draining vessels, industrial applications.

Features and benefits Pomona can be supplied as bare-shaftpump as well as with the motor on atrolley, carrying frame or base plate.


(5130 m3/h)Head H: max. 2,1 mLiquid temperature: 5 C +40 CDischarge Size: DN 300, DN 500 and

DN 800

ApplicationsSludge and wastewater treatment plants,media moving in recirculation systemsand storm water pumping.

Features and benefits high-eciency stainless steel impeller, completely submerged installation, built-in motor protection.


PomonaPortable, self-priming pumps for temporaryor permanent installation

SRP pumpsSubmersible recirculation pumps

Technical dataLiquid temperature: +5 C +40 CpH: 410Flow Q: max. 17 500 m3/hMax din. Viscosity: 500 mPasMaximum density: 1 060 kg/m3Max instal. depth: 20 mPropeller diameter: 1802 600 mmSpeed: 221400/min

ApplicationsIndustrial and municipal waste watertreatment. Homogenization in variety ofindustrial technology processes. Agriculture.

Features and benefits wide range of flexible installationaccessories,

easy to maintain and service withoutuse of special tools,

electronic leak sensor in gearbox/shaftseal housing,

shaft seal protected against abrasivematerials

Self-cleaning stainless steel or polyamidepropeller.

AMD, AMG, AFGMixers and flowmakers

20 50 100 200 500 1000 2000Q [l/s]

0,2

0,4

0,60,81.01,0

1,52,0

H [m]

1 2 5 1010 20 50 100100 200Q [m/h]

6

1010

1520

30

H [m]

16








Technical dataFlow Q: max. 300 m3/hHead H: max. 100 mLiquid temperature: 0 C +40 C

ApplicationsWater level maintenance and drainage onconstruction sites, excavations, in tunneling,mines, canal building industry.

Features and benefits extremely hard-wearing due to speciallyselected materials,

easy installation no maintenance.

Technical dataFlow Q: max. 432 m3/hHead H: max. 102 mLiquid temperature: 0 C +40 CInstallation. depth: max. 25 m.

ApplicationsDewatering on construction sites,excavation sites in tunnels, mines. Drainingin underground building pits, industrialpits. Water containing solids, max. particlesize 13 mm.

Features and benefits durability, ductile/high-chrome impeller, easy to use, high eciency, compact design, high pressure capabilities.

Technical dataFlow Q: max. 155 m3/hHead H: max. 51 mLiquid temperature: 0 C +40 CInstallation. depth: max. 25 m.

ApplicationsDraining on construction sites, excavationsites. max particle size 20 mm. Wastewater transfer and lifting, with freestanding or fixed installation.

Features and benefits large head, flexible adaptation to the installationconditions,

easy service and maintenance.

Options dierent discharge connections, auto-coupling system, monitoring unit.

DPKSubmersible drainage pumps

DWKHeavy-duty dewatering pumps

DWContractor submersible pumps

1 2 4 1010 20 40 100100Q [m3/h]

4

20

10

20

4060100100

H [m]

400

H [m]

DWK-E

DWK-O

Q [l/s]

10080

504030

20

101 2 4 6 10 20 40 60 100

H [m]

Q [l/s]

5040

30

20

101 2 4 6 10 20 40 60

17







Technical dataFlow rate Q: up to 600 l/hHead H: up to 5,5 mLiquid: pH 200 kW gas-fired boilers, oil-fired boilers,

18








Technical data - B LiftawayInlet dimension: 3DN 100Discharge connection:Eective volume:

DN 4040 l

Technical data - C LiftawayInlet dimension: 3DN 100

+ 1DN 40/50Discharge connection:Eective volume:

DN 40 13 l

ApplicationsCollection of drainage and surface water,pumping of wastewater from basementand laundry rooms below sewer level.

Features and benefits To be fitted with pumps from the Unilift KP and AP range.

Liftaway B telescopic part for easy heightadjustment,

flexible and easy installation.

Liftaway C functional design and easy to clean, overflow protection device, active carbon filter to eliminate odours, compact and slim for easy installationunder a washbasin or in a closet.

Technical dataFlow rate: max. 60 l/sec

(216 m3/h) (recommended 31 l/sec (110 m3/h)

Head H: max. 29 mLiquid temperature: 0 C +40 CDischarge diameter: DN 80DN 100

ApplicationsSingle-and multi-family homes, weekendcottages, public buildings, hotels,restaurants, indoor wastewater lifting.

Features and benefits ready to install, complete factory design, multi-directional pipe connection, cable plug connection, single channel or vortex impeller, solids passage up to 100 mm, low clogging risk, minimal downtime risk, low operating costs outdoor, air-cooled motors easily replaceable shaft seal, modular design.

MultiLift MSS, M, MD, MLD,MD1, MDV lifting stationsHigh performance wastewater liftingstations

Liftaway B and C.Domestic lifting stations


ApplicationsPressure boosting in water supply systems,irrigation systems, water treatment plants,fire protection systems, industry.

Features and benefits constant pressure, easy to install, low power consumption, a wide range of applications.

Options external communication: GENIbus otherbus G 100 module, Ethernet.

Hydro MPC, Hydro Solo-E, -S, Hydro Multi-E,-SPressure boosting systems

1 10 20 30 50Q [l/s]

4

6

10

20

30

H [m]

5 10 20 50 100 200 5001000Q [m/h]

20

40

6080

100

150

H [m]

19








Technical data Mains voltage: 1200240 V 3400500 V 3525600 V 3575690 V

ApplicationsAdjustment of the pump performance to the demand. Together with sensors, the CUE oers these control modes: proportional dierential pressure constant dierential pressure constant pressure constant pressure with stop function constant level constant level with stop function constant flow rate constant temperature.

The CUE can also be controlled by anexternal signal or via GENIbus.

Features and benefits adjustment of the pump performance tothe demand, thus saving energy.

easy installation, as the CUE is designedfor GRUNDFOS pumps.

short-circuit-protected output; nomotor-protective circuit breaker required.

fault indication via display and a relay,if fitted.

external setpoint influence via threeprogrammable inputs.

CUEFrequency converters for three-phase pumps

Technical data Number of pumps: max. 6 db Motor: from 0,3775 kW

(on request up to 315 kW) Enclosure class: IP 54

ApplicationsControl of parallel machine groups inheating and cooling systems, water supplysystems, irrigation systems, water treatmentsystems, fire protection systems, industry.

The Control MPC is designed for thesepump types: CR(E), CRI(E), CRN(E) NB(E), NBG(E) NK(E), NKG(E) TP TPE 1000 TPE 2000 HS SP MAGNA, MAGNA3

Features and benefits simple installation and start-up, simple handling, pump specific software, modular solution with possibility ofexpansion,

data communication via Ethernet, LON,PROFIBUS, etc.

Control MPCControl and monitoring units

Technical dataelectric driveFlow Q: 571100 m3/hHead H: max. 124 mWith diesel engineFlow Q: 57920 m3/hHead H: max. 144 mLiquid temperature: +5 C +40 C

ApplicationsPump station for fire protection systems.

Features and benefits selectable drive: electrical or diesel, FM approved and UL listed, simple installation and easy maintenance, high level of functionality and reliability.

Fire DNF, Fire HSEFFire pump systems

60 100 200 500 1000 2000Q [m/h]

20

40

6080

100

150

H [m]







ApplicationsMonitoring and protection of pumps.

Features and benefits protection against dry running protection against liquid temperaturesexceeding 130 C 5 C

protection against too high motortemperatures

manual or automatic restarting possible from a remote PC

simple installation (plug-and-play technology)

robust sensor.

ApplicationsMonitoring and protection of pumps,protection against dry running andsubmersible motor overheating, constantmonitoring of pump energy consumption,reading data from a remote control (R 100).

Features and benefits protection against dry running andoverheating,

constant monitoring of pump energyconsumption,

reading data from a remotecontrol (R100).

Options connection to large control systems viabus communication.

connection of external sensors (SM 100).

MP 204, CU 300, CU 301Control and monitoring units

LiqTecControl and monitoring units

ApplicationsReading and setting various operating andfault signals of electronically controlledpumps.

Features and benefits simple and quick setting of the pump, reading of various operating and fault signals

printing of status information.

R 100Infrared remote control

20








Technical data Mains voltage: 1200240 V 3400500 V 3525600 V 3575690 V

ApplicationsAdjustment of the pump performance to the demand. Together with sensors, the CUE oers these control modes: proportional dierential pressure constant dierential pressure constant pressure constant pressure with stop function constant level constant level with stop function constant flow rate constant temperature.

The CUE can also be controlled by anexternal signal or via GENIbus.

Features and benefits adjustment of the pump performance tothe demand, thus saving energy.

easy installation, as the CUE is designedfor GRUNDFOS pumps.

short-circuit-protected output; nomotor-protective circuit breaker required.

fault indication via display and a relay,if fitted.

external setpoint influence via threeprogrammable inputs.

CUEFrequency converters for three-phase pumps

Technical data Number of pumps: max. 6 db Motor: from 0,3775 kW

(on request up to 315 kW) Enclosure class: IP 54

ApplicationsControl of parallel machine groups inheating and cooling systems, water supplysystems, irrigation systems, water treatmentsystems, fire protection systems, industry.

The Control MPC is designed for thesepump types: CR(E), CRI(E), CRN(E) NB(E), NBG(E) NK(E), NKG(E) TP TPE 1000 TPE 2000 HS SP MAGNA, MAGNA3

Features and benefits simple installation and start-up, simple handling, pump specific software, modular solution with possibility ofexpansion,

data communication via Ethernet, LON,PROFIBUS, etc.

Control MPCControl and monitoring units

Technical dataelectric driveFlow Q: 571100 m3/hHead H: max. 124 mWith diesel engineFlow Q: 57920 m3/hHead H: max. 144 mLiquid temperature: +5 C +40 C

ApplicationsPump station for fire protection systems.

Features and benefits selectable drive: electrical or diesel, FM approved and UL listed, simple installation and easy maintenance, high level of functionality and reliability.

Fire DNF, Fire HSEFFire pump systems

60 100 200 500 1000 2000Q [m/h]

20

40

6080

100

150

H [m]







ApplicationsMonitoring and protection of pumps.

Features and benefits protection against dry running protection against liquid temperaturesexceeding 130 C 5 C

protection against too high motortemperatures

manual or automatic restarting possible from a remote PC

simple installation (plug-and-play technology)

robust sensor.

ApplicationsMonitoring and protection of pumps,protection against dry running andsubmersible motor overheating, constantmonitoring of pump energy consumption,reading data from a remote control (R 100).

Features and benefits protection against dry running andoverheating,

constant monitoring of pump energyconsumption,

reading data from a remotecontrol (R100).

Options connection to large control systems viabus communication.

connection of external sensors (SM 100).

MP 204, CU 300, CU 301Control and monitoring units

LiqTecControl and monitoring units

ApplicationsReading and setting various operating andfault signals of electronically controlledpumps.

Features and benefits simple and quick setting of the pump, reading of various operating and fault signals

printing of status information.

R 100Infrared remote control

21








Technical dataRPS range: 010 bar100 DPS range: 06 barPower supply: 5 V DC PELVRPS output sign.: 0,53,5 V100 DPS output sign.: 0,54,5 VMeasuring technology: MEMS

Applications Domestic hot-water systems, centralheating systems, dry-running protectionin solar systems and boilers, surveillance of filter eciency,pressure control for manifold systems.

Features and benefits pressure- and temperature-sensorin-one,

dierential pressure sensor in highresolution version,

suitable for wet, aggressive liquids ratiometric output for DedicatedControls

wide range of accessories approved for drinking water.

Options SI 010 CNV power supply and signalconverter for desired 4-20 mA signal output. Additionally, the SI 010 CNVconverts to 2-10 V or 1-5 V.

RPS and DPS 100Relative and dierential pressure sensorsfor liquids

Technical dataFlow Q: 1400 l/minPower supply: 5 V DC PELVOutput signal: 0,53,5 VLiquid temperature: 0 C 100 CMeasuring technology: MEMS

Applications Thermal management in solar heatingsystems, industrial process flow control.Cooling and temperature control for e.g.manifold systems. Floor/radiant heatingand valve systems.

Features and benefits no moving parts, flow and temperature sensor in one,

flow range 1-12 and 2-40 l/min in 42 %glycol mixture with stainless-steel flowpipe and insert,

suitable for wet, aggressive liquids, ratiometric output for Dedicated Controls,

wide range of accessories, approved for drinking water.

Options Power supply and signal converter SI 010CNV for desired 4-20 mA signal output.Additionally, the SI 010 CNV converts to2-10 V or 1-5 V.

VFSVortex flow sensor for liquids

Technical dataThe CIM/CIU interfaces enable theconnection of Grundfos electronic productsto standard fieldbus networks. CIM can be installed as an add-on modulein 11-22 kW E-pumps and CU 361, for otherproducts, use the CIU box with internalpower supply.

ApplicationsThe following product ranges aresupported: MAGNA/UPE 2000* CRE/CRIE/CRNE, MTRE,CME, NBE/NKE, TPE 1000, TPE 2000

Hydro MPC/Multi-E, Control MPC, CUE CR Monitor* MP 204* Dedicated controls*

* Not supported by all CIM/CIU types.

Features and benefits available with GENIbus, LONbus, ModbusRTU and Profibus DP systems,

modular design, standard functional profiles.

CIM / CIUCommunication Interface Units

22








Technical dataRPS range: 010 bar100 DPS range: 06 barPower supply: 5 V DC PELVRPS output sign.: 0,53,5 V100 DPS output sign.: 0,54,5 VMeasuring technology: MEMS

Applications Domestic hot-water systems, centralheating systems, dry-running protectionin solar systems and boilers, surveillance of filter eciency,pressure control for manifold systems.

Features and benefits pressure- and temperature-sensorin-one,

dierential pressure sensor in highresolution version,

suitable for wet, aggressive liquids ratiometric output for DedicatedControls

wide range of accessories approved for drinking water.

Options SI 010 CNV power supply and signalconverter for desired 4-20 mA signal output. Additionally, the SI 010 CNVconverts to 2-10 V or 1-5 V.

RPS and DPS 100Relative and dierential pressure sensorsfor liquids

Technical dataFlow Q: 1400 l/minPower supply: 5 V DC PELVOutput signal: 0,53,5 VLiquid temperature: 0 C 100 CMeasuring technology: MEMS

Applications Thermal management in solar heatingsystems, industrial process flow control.Cooling and temperature control for e.g.manifold systems. Floor/radiant heatingand valve systems.

Features and benefits no moving parts, flow and temperature sensor in one,

flow range 1-12 and 2-40 l/min in 42 %glycol mixture with stainless-steel flowpipe and insert,

suitable for wet, aggressive liquids, ratiometric output for Dedicated Controls,

wide range of accessories, approved for drinking water.

Options Power supply and signal converter SI 010CNV for desired 4-20 mA signal output.Additionally, the SI 010 CNV converts to2-10 V or 1-5 V.

VFSVortex flow sensor for liquids

Technical dataThe CIM/CIU interfaces enable theconnection of Grundfos electronic productsto standard fieldbus networks. CIM can be installed as an add-on modulein 11-22 kW E-pumps and CU 361, for otherproducts, use the CIU box with internalpower supply.

ApplicationsThe following product ranges aresupported: MAGNA/UPE 2000* CRE/CRIE/CRNE, MTRE,CME, NBE/NKE, TPE 1000, TPE 2000

Hydro MPC/Multi-E, Control MPC, CUE CR Monitor* MP 204* Dedicated controls*

* Not supported by all CIM/CIU types.

Features and benefits available with GENIbus, LONbus, ModbusRTU and Profibus DP systems,

modular design, standard functional profiles.

CIM / CIUCommunication Interface Units

compact design. lubricated by the pumped liquid,







Technical dataPressure Range: 010 barPower supply: 1230 V DCOutput Signal: 420 mALiquid temperature: -10 C + 70 CMeasuring technology: MEMS

Applications Pump and pump control systems, heatexchanger control systems (monitoringfouling), filter monitoring, watertreatment systems.

Features and benefits venturi measurement constant dierential pressure, dierential pressure (remote), suitable for wet, aggressive liquids, wide range of accessories. suitable for drinking water.

Options upgrade package for TP1000, power supply SI 001 PSU for cable lengths > 30 m.

Technical dataVolume: 85000 lLiquid temperature: max. +90 CSystem pressure: max. 16 bar

Applications in housing, industry, agriculture,horticulture, in water supply, pressureboosting and irrigation systems.

Features and benefits optimal water supply, reduced numbers of pump starts, ideal for drinking water.

Pressure tanksDiaphragm and bladder tanks

DPIDierential pressure transmitter for liquids

Technical dataFlow Q: max. 10,2 m3/hHead H: max. 1630 mLiquid temperature: +3 C +50 CSystem pressure: max. 160 bar

ApplicationsThe BMP pumps for a wide range ofapplications from drinking water tochemical materials transfer. cleaning / washing, injecting misting processing seawater or brackish water desalination.

Features and benefits high eciency, small, light-weight pump, generates insignificant pulsations in thedischarge line,

no preventive maintenance required, long service life, few wear parts, wide speed control range,

extreme recirculation capability without overheating (up to 90 %),

BMPHigh-pressure piston pumps

23








Technical dataFilter through a / d: 5002500 m3Head H: max. 810 mLiquid temperature: +40 CSystem pressure: max. 80 bar

ApplicationsBrackish and seawater desalination plants.

Features and benefits energy recovery up to 60 %, compared to conventional systems, resulting in shortpayback period,

corrosion- and wear-resistant internalceramic components,

couplings for easy installation, high-grade stainless-steel frame andmanifold,

large flow rates and high heads, motor and bearings are standardcomponents,

maintenance-free shaft seal, V-belt drive with high eciency, easy to dismantle for service.

BMEXBooster systems for energy recovery inseawater reverse osmosis (SWRO) systems


ApplicationsReverse osmosis systems, water supplysystems, water treatment systems, industry.

Features and benefits high pressure / high flow rate low energy consumption, easy to install, compact design.

BME, BMETHigh-pressure booster systems



Features and benefits low noise, easy to install, modularity, compact design, design without seals, wide range of materials.

BM, BMBHigh pressure booster modules

0 400 800 1200 1600Q [m/nap]

0

1

2

3

4

5

[kWh]

tszrs1 2 4 1010 20 40 100100 200400

Q [m3/h]

10

20

4060100

200

400

H [m]

24








Technical dataFilter through a / d: 5002500 m3Head H: max. 810 mLiquid temperature: +40 CSystem pressure: max. 80 bar

ApplicationsBrackish and seawater desalination plants.

Features and benefits energy recovery up to 60 %, compared to conventional systems, resulting in shortpayback period,

corrosion- and wear-resistant internalceramic components,

couplings for easy installation, high-grade stainless-steel frame andmanifold,

large flow rates and high heads, motor and bearings are standardcomponents,

maintenance-free shaft seal, V-belt drive with high eciency, easy to dismantle for service.

BMEXBooster systems for energy recovery inseawater reverse osmosis (SWRO) systems



Features and benefits high pressure / high flow rate low energy consumption, easy to install, compact design.

BME, BMETHigh-pressure booster systems



Features and benefits low noise, easy to install, modularity, compact design, design without seals, wide range of materials.

BM, BMBHigh pressure booster modules

0 400 800 1200 1600Q [m/nap]

0

1

2

3

4

5

[kWh]

tszrs1 2 4 1010 20 40 100100 200400

Q [m3/h]

10

20

4060100

200

400

H [m]








ApplicationsBoiler feed pump, coolant circulation,water treatment.

Features and benefits a wide range of products, reliability, R100 infrared remote accessibility.


ApplicationsLiquid transfer in machine tool systems,components washing machines, chillerunits, industrial washing systems,condensate systems.

Features and benefits flexible installation length, wide range of products, reliability, easy to maintain, easy to install.

MTRE, SPKEMultistage centrifugal immersible pumps - electronically controlled

MTR, SPK, MTHMultistage, immersiblecentrifugal pumps

Technical dataFlow Q: max. 21,3 m3/hHead H: max. 13,5 mLiquid temperature: 0 C +60 C

ApplicationsLiquid transfer in machining centers,filter and conveyor systems.

Features and benefits high-eciency motor and hydraulic, wide range, flexible installation length, reliability, no shaft seal,

easy installation. semi-open impeller,

MTASingle-stage coolant pump

1 2 4 6 1010 20 40 80Q [m/h]

20

4060

100150200300400H [m]

10 20 3040 60 100100 200 400Q [l/min]

1

2

46

101015

H [m]

25








Technical dataFlow Q: max. 90 m3/hHead H: 47 mLiquid temperature: 0 C +90 CSystem pressure: max. 16 bar

Application Liquid transfer, lubricating, cooling,machine tools, machining centers,grinding machines, parts cleaningsystems and industrial processes, wherethe semi-open impeller is preferred.

Features and benefits standard dimensions according to ENand ISO standards,

compact design, semi-open impeller / eective solidhandling,

standard EFF1 motor.

Technical dataFlow Q: max. 8,8 m3/hHead H: max. 55 mLiquid temperature: -55 C + 40 COperating pressure: max. 52 barRefrigerants: R744 (CO2),

R717 (NH3) HFCs

Application refrigerant circulating in cooling systems, refrigerant transport.

Features and benefits designed and optimised for CO2, low-energy consumption, easy integration into system, light weight and compact design.

RCCanned motor refrigerant circulationpumps

MTBSingle-stage centrifugal end-suctionpumps with semi-open impeller

Technical dataFlow Q: max. 51 m3/hHead H: max. 120 barLiquid temperature: 0 C +80 CSystem pressure: max. 130 bar

ApplicationMachine tool industry and other industrialprocesses, metalworking fluids, cutting,grinding, cutting oils, oil-in-wateremulsions, refrigeration fluid transfer.

Features and benefits high eciency, wear resistance compact design, low noise and vibration levels.

Options dry installation special shaft seals, variety of connection methods.

MTSHigh-pressure pumps for tank topinstallation

10,5 11 2 4 6 8 10101

2

46

1010

20

4060

H [m]

Q [m3/h]5 6 10 20 40 60 100

Q [m/h]

5

10

20

4050

H [m]

26








Technical dataFlow Q: max. 90 m3/hHead H: 47 mLiquid temperature: 0 C +90 CSystem pressure: max. 16 bar

Application Liquid transfer, lubricating, cooling,machine tools, machining centers,grinding machines, parts cleaningsystems and industrial processes, wherethe semi-open impeller is preferred.

Features and benefits standard dimensions according to ENand ISO standards,

compact design, semi-open impeller / eective solidhandling,

standard EFF1 motor.

Technical dataFlow Q: max. 8,8 m3/hHead H: max. 55 mLiquid temperature: -55 C + 40 COperating pressure: max. 52 barRefrigerants: R744 (CO2),

R717 (NH3) HFCs

Application refrigerant circulating in cooling systems, refrigerant transport.

Features and benefits designed and optimised for CO2, low-energy consumption, easy integration into system, light weight and compact design.

RCCanned motor refrigerant circulationpumps

MTBSingle-stage centrifugal end-suctionpumps with semi-open impeller

Technical dataFlow Q: max. 51 m3/hHead H: max. 120 barLiquid temperature: 0 C +80 CSystem pressure: max. 130 bar

ApplicationMachine tool industry and other industrialprocesses, metalworking fluids, cutting,grinding, cutting oils, oil-in-wateremulsions, refrigeration fluid transfer.

Features and benefits high eciency, wear resistance compact design, low noise and vibration levels.

Options dry installation special shaft seals, variety of connection methods.

MTSHigh-pressure pumps for tank topinstallation

10,5 11 2 4 6 8 10101

2

46

1010

20

4060

H [m]

Q [m3/h]5 6 10 20 40 60 100

Q [m/h]

5

10

20

4050

H [m]







Technical dataFlow Q: max. 30 l/hPressure p: max. 16 barTurn-down ratio: 1:3000 or

1:1000Liquid temperature: max. +45 C

ApplicationHigh-performance pump series of largeflow rate and pressure ranges for industrialareas: process water, food and beverage industry, ultrafiltration and reverse osmosis, paper production, boiler feed water, CIP (Clean-In-Place) [on site cleaning].

Features and benefits internal stroke-speed and frequencycontrol,

manual, pulse and 0/4-20 mA control, batch, timer cycle, timer week control, FlowControl with selective fault diagnosis, pressure monitoring,

integrated flow measurement andAutoFlowAdapt,

0/4-20 mA and 2 relay outputs

power supply 100-240 V, 50/60 Hz. auto deaeration,

Technical dataFlow Q: max. 15 l/hPressure p: max. 10 barTurn-down ratio: 1:1000Liquid temperature: max. +45 C

ApplicationUser-friendly pump series with standardinputs and outputs for general applications: water, wastewater, swimming pool water, cooling tower, chemical industry.

Features and benefits internal stroke-speed and frequencycontrol with stepper motor,

flexible control cube and mounting plate, click wheel and graphical display, capacity setting in ml/h, l/h, or gph, manual, pulse and 0/4-20 mA control, 2 relay outputs, smooth dosing of degassing liquids, slow Mode, power supply 100-240 V, 50/60 Hz.

Technical dataFlow Q: max. 15 l/hPressure p: max. 10 barTurn-down ratio: 1:1000Liquid temperature: max. +45 C

ApplicationDosing pump series with basic functions: motor vehicle washing, irrigation swimming pool water, cooling tower, chemical processes.

Features and benefits internal stroke-speed and frequency controlwith stepper motor,

only 2 models from 0.006 to 15 l/h, smooth continuous dosing, always full stroke length, flexible mounting plate, capacity adjustment knob, manual control (0.1-100 %), pulse control (1:n), external stop and empty tank input, power supply 100-240 V, 50/60 Hz.

DDEDigital diaphragm dosing pumps

DDCDigital diaphragm dosing pumps

DDADigital diaphragm dosing pumps

11 6 15Q [l/h]

4

1010

p [bar]

00

11 6 9 15Q [l/h]

4

71010

p [bar]

00

0 11 30Q [l/h]

4

71010

16p [bar]

00

7,51217

27








Technical dataFlow Q: max. 150 l/hLiquid temperature: max. 70 CPressure: max. 16 bar

Applications

wastewater treatment, water treatment,

wash systems, swimming pools, process plants, paper production, food and beverage industry.

Features and benefits internal stroke-speed and frequencycontrol with brushless DC-motor,

capacity setting in ml/h or l/h, smooth dosing through variable speed, reliable dosing of viscous liquids, side-fitted control panel, manual/pulse control, 4-20 mA control, easy calibration, pioneering system for flow and pressuremonitoring in the dosing head (controlvariant AF),

PROFIBUS interface (control variant AP).

Technical dataFlow Q: max. 765 l/h

(pump with twodosing heads:2 765 l/h)

Liquid temperature: max. 70 CPressure: max. 16 bar

Applications drinking water treatment, wastewater treatment (sediment /sludge treatment)

paper and textile industry.

Features and benefits robust design, Stroke length adjustment.

Options pulse Control (AR control variant), analog control (control variant AR), level input from storage tank (controlvariant AR),

motor frequency control, ATEX (DMX 226).

DMXMotor-driven diaphragm dosing pumps

DDIDigital diaphragm dosing pumps

Technical dataFlow Q: max. 940 l/hLiquid temperature: max. 50 CPressure: max. 18 bar

Applications water treatment wastewater treatment, wash systems, swimming pools, process plants, filtration systems, reverse osmosis.

Features and benefits capacity setting in ml/h or l/h, internal stroke-speed and frequencycontrol with brushless DC motor,

front- or side-fitted control panel withdisplay,

control panel lock, 4-20 mA control, pulse-/timer-based batch control, anti-cavitation function, easy calibration function, Fieldbus communication module(optional),

diaphragm leakage sensor.

DMEDigital diaphragm dosing pumps

0 2,2 60 150Q [l/h]

1

4

1010

16p [bar]

00

20 190 460 4000Q [l/h]

1

3

6

1010

16p [bar]

00

1 2,5 1010Q [l/h]

1

4

1010

18

p [bar]

376 940







Technical dataMeasured and controlled parameters:Conex DIA-1: Cl2, ClO2, O3, PAA or

H2O2, fluoride, pH or ORP

Conex DIA-2: 1: Cl2, ClO2, O3 and H2O2, 2: pHConex DIA-2Q: 1: Cl2, ClO2, O3, PAA or

H2O2 2: fluoride, pH or

ORPConex DIS-C: Conductivity (inductive

or conductive probes)Conex DIS-PR: pH or ORPConex DIS-D: Cl2, ClO2 or O3.

ApplicationsInstrumentation in disinfection processes: drinking water industrial water

pool water. wastewater (only euent)

grundfos catalogue industry and water utility eng 2014

Documents

horizontal pumps

submersible pumps sp

singlestage centrifugal

vertical pumps cr

submersible pumps bm

high pressure piston

environmental pumps

screw pumps mts3