gross star hood install manual
TRANSCRIPT
Field Installation Instructions for the Gross Star-Grossing
Station Hood Assembly
MATERIALSB21113-03 – Sliding door assembly (1 supplied)
B21113-09 – Side shield (2 supplied)B21113-10 – Left cover guide or “hockey stick” (with
mounting bracket attached) (1 supplied)B21113-11 – Right cover guide or “hockey stick” (with
mounting bracket attached) (1 supplied)1001432 – 8 MM x 20 screws (8 supplied)
¾” OD x .312 ID x 1/8” plastic washers (6 supplied)¼ x 20 x 5/8 screws (4 supplied)
B21113 – Hood Assembly drawings C8007058 – Hood Assembly Install Instructions
TOOLSPower drill
# 39 drill bit (supplied)# 5 drill bit (supplied)¼ - 20 tap (supplied)3/16” Allen wrench
Phillips head screwdriverTape measure
MarkerCenter punch
Gross Star Hood Assembly
PAGE 2
B121113-03 – Sliding door assembly
B121113-09 – side shield
B121113-10 – Front cover guide
Fig. 1
Fig. 3
Fig. 2
MATERIALSB21113-09 – Side shield
1001432 – 8 MM x 20 screws ¾” OD x .312 ID x 1/8” plastic washers
PROCEDURESBefore you can begin the installation, you need to remove the 8 screws and 6 washers from the 2 inside corners (4 screws on each side) of the canopy section of the Gross Star-Grossing Station (Fig. 1).
To attach the side shields, start by sliding (6) ¾” OD plastic washers onto (6) 8 MM screws (Fig. 2).
Position a side shield with its flat end on the bottom and cutout end on top. Slide a screw with washer through the center hole on the side shield (Fig. 3).
TOOLS3/16” Allen wrench
Gross Star Hood Assembly
PAGE 3
Fig. 1
Fig. 3
Fig. 2
MATERIALSB21113-09 – Side shield
B21113-10 – Left hockey stick (with mounting bracket attached) B21113-11 – Right hockey stick (with mounting bracket attached)
1001432 – 8 MM x 20 screws¾” OD x .312 ID x 1/8” plastic washers
PROCEDURESAlign the side shield screw and washer over the second hole from the bottom. Tighten the screw using a 3/16” Allen wrench. Add a screw and washer to the top and bottom hole in the side panel and tighten (Fig. 1).
Attach a second side shield to the opposite side the same way (Fig. 2).
Position a hockey stick with its groove side facing inward and insert (1) 8 MM screw through the hole. The hockey sticks do not use a washer (Fig. 3).
TOOLS3/16” Allen wrench
Gross Star Hood Assembly
PAGE 4
Fig. 1
Fig. 3
Fig. 2
MATERIALSB21113-10 – Left hockey stick (with mounting bracket attached)
B21113-11 – Right hockey stick (with mounting bracket attached) — right 1001432 – 8 MM x 20 screws
TOOLS3/16” Allen wrench
Gross Star Hood Assembly
Page | 5
Fig. 2
Fig. 3
Fig. 2
MATERIALSB21113-10 – Left hockey stick (with mounting bracket attached) B21113-11 – Right hockey stick (with mounting bracket attached)
PROCEDURESTrace around the inside edge of the mounting bracket’s screw slots (Fig. 1).
Remove the hockey stick from the unit and tighten the screws on its mounting bracket. Repeat these same procedures for the second hockey stick (Fig. 2).
Verifying the location of the mounting holes will require a number of measurements. Start by finding the center of each traced mark (Fig. 3).
TOOLSTape measure
Marker 3/16” Allen wrench
Gross Star Hood Assembly
Page | 6
Fig. 1
Fig. 3
Fig. 2
MATERIALSGross Star backsplash
TOOLSTape measure
Marker
Gross Star Hood Assembly
Page | 7
Fig. 1
Fig. 3
Fig. 2
MATERIALSGross Star backsplash
TOOLSTape measureCenter punch
Power drill#39 drill bit
Gross Star Hood Assembly
Page | 8
Fig. 2
Fig. 1
Fig. 3
MATERIALSGross Star backsplash
¼ x 20 x 5/8 screws
TOOLSPower drill#5 drill bit¼-20 tap
Gross Star Hood Assembly
Page | 9
Fig. 3
Fig. 1
Fig. 2
MATERIALSB21113-03 – Sliding door assembly
PROCEDURESUsing 2 hands align the front roller bearings attached to the sliding door assembly with the notches in the hockey sticks (Fig. 1).
With the front bearings located in the hockey sticks, lower the door assembly slightly and push forward to slide it along the guide tracks in the hockey sticks (Fig. 2).
Lower the second set of roller bearings into the notch on each hockey stick (Fig. 3).
TOOLS
Gross Star Hood Assembly
Page | 10
Fig. 1
Fig. 3
Fig. 2
MATERIALSB21113-03 – Sliding door assembly
PROCEDURESGently glide the door all the way in and rest it in its open position (Fig. 1).
Verify the sliding door is operating smoothly by sliding it open and closed a few times (Fig. 2 and Fig. 3).
After checking the door operation, verify that all fasteners are tight. Once verified, remove the protective paper from all the plastic parts to complete the assembly.
TOOLS
Gross Star Hood Assembly
Page | 11
Fig. 1
Fig. 3
Fig. 2