greensmaster 1000 series – a new legend is born....greensmaster® flex 1820 & 2120 the...

432019 Toro Commercial Equipment Guide 19-003-T Rev. 1/19

Greensmaster® 1000 Series – A new legend is born.Toro’s new line of fixed-head walk behind greensmowers have been thoughtfully engineered to bring each operator and greensmower into

perfect harmony. Multiple innovations, starting with an industry-first telescoping handle, come together to deliver unparalleled cut quality

and consistent playability on each and every green. The uniquely modular design also makes the new Greensmaster 1000 Series mowers

easier to maintain, saving significant time and money.

NEW


* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only. Actual products offered for sale may vary in use, design, required attachments and safety features. Consult your local Toro Distributor.

The Greensmaster 1018 is manufactured in Tomah, WI ISO 9002 Certified Plant.

Greensmaster® 1018 Specifications*

GREENSMASTER 1018, MODEL 04820ENGINE Honda GX120 - 3.5 hp (2.6 kW) @3600 rpm, gasoline with integral lighting coil.

FUEL CAPACITY 2.1 qts (2L)

FRAME Fully modular design allows quick disassembly for service / maintenance of all major components.

TRACTION DRIVE Full gear drive transmission with integral traction differential and traction drive disconnect to ease movement during service / maintenance operations. Interchangeable drum drive gear cases.

TRACTION DRUM Dual position traction drum with positions for contour following or forward weight bias at higher heights of cut.

GROUND SPEED Mowing Speed: 2.0 mph (3.2 km/h) to 3.5 mph (5.6 km/h) Transport Speed: 5.3 mph (8.5 km/h)

CLUTCH Externally-mounted two sided dry disc clutch actuated by dual motion bail.

BRAKE Service / parking – band type.

CUTTING UNIT DRIVE Quick change dual speed gear drive.

CUTTING UNIT ATTACHMENT Detachable cutting unit allows easy removal for service / maintenance or cutting unit exchange for different uses.

CUTTING UNIT OPTIONS 11-blade cutting unit 14-blade cutting unit

CONTROLS Engine mounted: recoil starter, choke, fuel shutoff. Handle mounted: on/off switch, throttle lever, dual motion traction / safety bail, reel engage lever, service/park brake lever, hour meter, light switch (optional).

HANDLE Loop handle with telescoping adjustment with 5" (12.7 cm) total travel, rubber isolated to minimize operator influence during mowing.

TRANSPORT TIRES / KICKSTAND Optional – Two, quick-detachable pneumatic tires (3.00X3.25-6). Kickstand is standard.

WIDTH OF CUT 18" (45.7 cm)

HEIGHT OF CUT RANGEFor Greens: (Drum Position One) 0.062" to 0.312" (1.5 mm to 8 mm) For Tees: (Drum Position Two) 0.25" to 0.625" (6 mm to 16 mm) High Height of Cut Kit: (Drum Position Two) 1.18" (30 mm)

WEIGHT 210 lbs (95.2 kg) with 11-blade cutting unit, aluminum Wiehle roller.

MAINTENANCE REQUIREMENTS No daily greasing required.

CERTIFICATION Designed in accordance to applicable ANSI and CE specifications.

WARRANTY Two-year limited warranty. Refer to the Operator’s Manual for further details.















CUTTING UNIT OPTIONS 8-blade cutting unit 11-blade cutting unit 14-blade cutting unit






WEIGHT 224 lbs (100 kg) with 11-blade cutting unit, aluminum Wiehle roller.

MAINTENANCE REQUIREMENTS No daily greasing required. On board backlapping available with optional kit.



462019 Toro Commercial Equipment Guide 19-003-T Rev. 7/19The Greensmaster 1026 is manufactured in Tomah, WI ISO 9002 Certified Plant.

* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only. Actual products offered for sale may vary in design, required attachments and safety features. Consult your local Toro Distributor.












CUTTING UNIT OPTIONS 8-blade cutting unit 11-blade cutting unit 14-blade cutting unit




WIDTH OF CUT 26" (66 cm)


WEIGHT 240 lbs (108.8 kg) with 11-blade cutting unit, aluminum Wiehle roller.

MAINTENANCE REQUIREMENTS No daily greasing required. On board backlapping available with optional kit.




Greensmaster® Flex™ 1820 & 2120The Greensmaster® Flex™, available in both 18 and 21 inch cutting widths, takes Toro’s industry leading

cutting performance to a whole new level. Additional innovations in the areas of productivity, operational

versatility and serviceability combine to make this mower an outstanding value.


Greensmaster® Flex 1820 & 2120 Specifications*


The Greensmaster Flex 1820 & 2120 are manufactured in Tomah, WI ISO 9002 Certified Plant.

GREENSMASTER FLEX 1820, MODEL 04045 GREENSMASTER FLEX 2120, MODEL 04044

ENGINE Subaru® Heavy-Duty Industrial, 4.3 hp (3.2 kW) @ 4000 rpm, OHC, 4-cycle, CARB, EPA, EU, China certified gasoline engine with integral lighting coil. Displacement: 7.7 cu in. (126 cc). Cast iron cylinder sleeve. Electronic ignition. Maximum noise suppression muffler.

FUEL CAPACITY .79 gallons (3.0 liters) regular grade unleaded gasoline.

TRANSMISSION Engine powered multi-disk wet clutch to the first stage of a multi-ribbed poly V-belt drive. The traction drums are belt driven through a spur gear planetary differential with integral band style service/parking brake.

MAINTENANCE No grease zerks, sealed bearing design reduces daily maintenance.

GROUND SPEED Mowing speed: 1.6-3.7 mph (2.5-5.9 km/h). Transport speed (maximum): 5.7 mph (9.2 km/h).

TRACTION DRUM Dual cast aluminum 7.5” (19 cm) diameter with taper on outer 2” (5 cm).

CONTROLS Engine Controls: Recoil starter, choke, fuel shut-off. Handle Controls: on/off (‘ignition’) switch, hour meter, throttle, dual function traction/reel control lever, operator presence control, service/park brake lever, on/off light switch (optional blank slot in console).

HANDLE Loop style, molded contour upper, 1” (2.5 cm) diameter lower tube. Two angular adjustments and lift assist kickstand with 2.0 inches of telescoping adjustment.

TRANSPORT TIRES/KICKSTAND Quick detachable 3.00/3.25 x 6 pneumatic. Lift assist kickstand standard equipment. Loop style with service position lock, 1” (2.5 cm) diameter tube.

REEL CONSTRUCTION8-Blade Reel: 5” (12.7 cm) diameter, 8-EdgeSeries™ steel blades welded to 5 steel spiders (no 8-blade, 18” available). 11-Blade Reel: 5” (12.7 cm) diameter, 11-EdgeSeries™ steel blades welded to 5 steel spiders. 14-Blade Reel: 5” (12.7 cm) diameter, 14-EdgeSeries™ steel blades welded to 5 steel spiders.

SUSPENSION Semi-floating cutting unit separable from drive unit, pivoting around reel centerline (pitch axis) and pivoting around bedknife centerline side to side (roll axis).

WIDTH OF CUT 18" (45.7 cm) 21" (53.3 cm)

HEIGHT OF CUT Cutting height is adjusted on front roller by two vertical screws and held by two locking cap screws. Bench height of cut range is .062"-.297" (1.6-7.5 mm) with high height of cut kit, range is .297"-1.0" (7.5-25.4 mm). Effective height of cut may vary depending on turf conditions and bedknife installed.

CLIP FREQUENCIES Reel drive consists of three pulleys of different diameter. 6-clip adjustments per reel, based on pulley configuration.

REEL DRIVE Transmission reel clutch shaft to a drive shaft with a pair of beam style couplers.

CUTTING UNIT CONSTRUCTION Machined cast aluminum frame.

CUTTING UNIT ADJUSTMENT/SERVICE Cutting unit detachable from traction unit. Dual screw “click” adjustments to reel. Front roller height of cut adjustment. Sealed stainless steel reel bearings.

BEDKNIFE EdgeMaxTM Microcut Bedknife is standard on 11 & 14-blade cutting unit. EdgeMax bedknife is heat treated solid tool steel.

GRASS BASKET Molded polyethylene with integrated graphics highlighting overlap guidelines, vented for high-efficiency collection.

ROLLERS Front Roller: Optional – must be ordered. Rear Roller: Aluminum full roller 2” (5.1 cm) diameter with sealed bearings.

WORKING WEIGHT 254 lbs. (115 kg) w/basket, w/o transport tires and groomer. 260 lbs. (118 kg) w/basket, w/o transport tires and groomer.

CERTIFICATION / WARRANTY Designed in accordance to ANSI B71.4-2012 and European Community (CE) specifications. Two-year limited warranty. Refer to the Operator’s Manual for further details.

GREENSMASTER FLEX 2120 ACCESSORIESGREENSMASTER FLEX 1820 ACCESSORIES

GROOMER OPTIONS04648 Universal Groomer Drive04802 Groomer Reel – Twin Tip127-6119 Groomer Quick Up Kit (w/o groomer)04270 Greens Grooming Brush (21") – Soft04271 Greens Grooming Brush (21") – Stiff

CUTTING UNITS & REEL OPTIONS04290 11-Blade DPA Cutting Unit04292 14-Blade DPA Cutting Unit

BEDKNIFE & BEDBAR OPTIONS93-4263 Tournament Bedknife93-4264 Low Cut Bedknife108-4303 Extended Microcut Bedknife93-4262 Microcut Bedknife108-4302 Extended Tournament Bedknife115-1881 EdgeMaxTM Tournament Bedknife120-9600 High Height of Cut Kit99-3794-03 Aggressive Bedbar

TRACTION UNIT ACCESSORIES04064 LED Light Kit04266 Push Broom Brush04123 Wheel Kit SCRAPER OPTIONS

125-3503 Narrow Wiehle Roller Scraper125-3504 Wide Wiehle Roller Scraper125-3505 Full Roller Scraper115-7377 Narrow Wiehle Roller Scraper Brush115-7378 Wide Wiehle Roller Scraper Brush115-7379 Full Roller Scraper Brush115-7380 Narrow Wiehle Roller Scraper Comb115-7381 Wide Wiehle Roller Scraper Comb115-7382 Full Roller Scraper Comb115-7383 Rear Roller Scraper

ROLLER OPTIONS04255 Front Narrow Wiehle Roller04256 Front Wide Wiehle Roller04250 Split Narrow Wiehle Roller107-3514 Front Wide Wiehle Roller – Steel04257 Front Full Roller04249 Split Full Front Roller04258 Long Front Narrow Wiehle Roller04267 Paspalum Roller115-7356 Rear Full Roller – Aluminum120-9595 Rear Full Roller – Steel115-7361 Front Roller Extension Kit120-9602 Rear Roller Adjustment Kit

STANDARD CUTTING UNIT EQUIPMENT115-1880 EdgeMaxTM Microcut Bedknife106-2648-01 Less Aggressive Bed Bar

CUTTING UNITS & REEL OPTIONS04291 14-Blade DPA Cutting Unit04289 11-Blade DPA Cutting Unit

BEDKNIFE & BEDBAR OPTIONS98-7260 Tournament Bedknife110-2301 Low Cut Bedknife110-2300 Extended Microcut Bedknife98-7261 Microcut Bedknife117-1532 EdgeMaxTM Tournament Bedknife117-1530 EdgeMaxTM Microcut Bedknife120-9600 High Height of Cut Kit110-2281-03 Aggressive Bedbar

ROLLER OPTIONS120-9607 Front Narrow Wiehle Roller120-9609 Front Wide Wiehle Roller120-9611 Front Full Steel Roller (2.5” dia.)121-4680 Front Full Extended Width Roller121-4681 Front Extended Wiehle Roller120-9602 Rear Roller Adjustment Kit121-4682 Rear Full Roller – Steel115-7361 Auxiliary Roller Kit

TRACTION UNIT ACCESSORIES04064 LED Light Kit04266 Push Broom Brush04123 Wheel Kit

SCRAPER OPTIONS120-9615 Narrow Wiehle Roller Scraper120-9616 Wide Wiehle Roller Scraper120-9617 Full Roller Scraper120-9621 Narrow Wiehle Roller Scraper Brush120-9622 Wide Wiehle Roller Scraper Brush120-9623 Full Roller Scraper Brush120-9624 Narrow Wiehle Roller Scraper Comb120-9625 Wide Wiehle Roller Scraper Comb120-9626 Full Roller Scraper Comb120-9627 Scraper Kit with Rear Roller (steel tube)

GROOMER OPTIONS04648 Universal Groomer Drive04801 Groomer Reel, Twin Tip127-6119 Groomer Quick Up Kit (w/o groomer)04268 Grooming Brush (18") – Soft04269 Grooming Brush (18") – Stiff

STANDARD CUTTING UNIT EQUIPMENT110-2282-01 Less Aggressive Bedbar

TOOLS04399 Turf Evaluator125-5610 Paper – Reel125-5611 Shim – Reel94-9010 Height of Cut Adjustment Bar04399 Turf Evaluator

TOOLS04399 Turf Evaluator125-5610 Paper – Reel125-5611 Shim – Reel94-9010 Height of Cut Adjustment Bar04399 Turf Evaluator131-6828 Angle Indicator131-6829 Mount-Angle Indicator


Greensmaster® eFlex® 2120The Greensmaster eFlex takes Toro’s industry leading cutting performance to a whole new level. Game-changing Lithium Ion battery technology combined with Toro innovations for improved cutting performance, allow you to quietly mow up to 7 average greens (35,000 sq. feet / 3251 sq. m) on a single charge! Additional innovations in the areas of productivity, operational versatility and serviceability combine to provide a more environmentally friendly “EnergySmart™” solution and ROI.


Greensmaster® eFlex® 2120 Specifications*

The Greensmaster eFlex 2120 is manufactured in Tomah, WI ISO 9002 Certified Plant.

GREENSMASTER eFLEX 2120, MODEL 04049

POWER Lithium-Ion battery pack – nominal 50.4-Volt 26.7 A-Hr (42 – 56 volt, 1.345 kW-hr) with integrated battery management system utilizing CAN communication with the machine controller and charger. Single battery affixed to unit and charged onboard.

ELECTRIC MOTOR Brushless permanent magnet DC motor – nominal 1.2 kW (~20A continuous, 30A peak) with integral motor controller and helical gear reduction.

BATTERY CHARGER Voltage and current controlled with CAN communication to manage storage wake-up and maintenance features. Complies to max voltage and current limits directed by the battery management system.

TRANSMISSION Permanent Magnet DC motor directly coupled to the first stage of a multi-ribbed poly-V belt drive. The traction drums are belt driven through a spur gear planetary differential with integral band style service/parking brake.

MAINTENANCE No grease zerks, sealed bearing design reduces daily maintenance.

GROUND SPEED Mowing speed: 0.9-3.7 mph (1.4-5.9 km/h). Transport speed (maximum): 5.7 mph (9.2 km/h).

TRACTION DRUM Dual cast aluminum 7.5” (19 cm) diameter with taper on outer 2” (5 cm).

CONTROLS Start/On/Off (‘ignition’) switch, LCD Information Center (reports multiple parameters including hours, battery life, faults, etc.) throttle, dual function traction/reel control lever, operator presence control, on/off ‘EZ-Turn’ switch, service/park brake lever, on/off light switch (optional blank slot in console).

HANDLE Loop style, molded contour upper, 1” (2.5 cm) diameter lower tube. Two angular adjustments and lift assist on kickstand with 2.0 inches of telescoping adjustment.

TRANSPORT TIRES/KICKSTAND Quick detachable 3.00/3.25 x 6 pneumatic. Lift assist kickstand standard equipment. Loop style with service position lock, 1” (2.5 cm) diameter tube.

REEL CONSTRUCTION 11/14-Blade Reel: 5” (12.7 cm) diameter, 8 high carbon steel blades welded to 5 steel spiders. 11-Blade Reel: 5” (12.7 cm) diameter, 11 high carbon steel blades welded to 5 steel spiders. 14-Blade Reel: 5” (12.7 cm) diameter, 14 high carbon steel blades welded to 5 steel spiders.

SUSPENSION Semi-floating cutting unit separable from drive unit, pivoting around reel centerline (pitch axis) and pivoting around bedknife centerline side to side (roll axis).


HEIGHT OF CUT Cutting height is adjusted on front roller by two vertical screws and held by two locking cap screws. Bench height of cut range is .062"-.297" (1.6-7.5 mm) with high height of cut kit, range is .297"-1.0" (7.5-25.4 mm). Effective height of cut may vary depending on turf conditions and bedknife installed.

CLIP FREQUENCIES Reel drive consists of three pulleys of different diameter. 6-clip adjustments per reel, based on pulley configuration.

REEL DRIVE Transmission reel clutch shaft to a drive shaft with a pair of beam style couplers.

CUTTING UNIT CONSTRUCTION Machined cast aluminum frame.

CUTTING UNIT ADJUST./SERVICE Cutting unit detachable from traction unit. Dual screw “click” adjustments to reel. Front roller height of cut adjustment. Sealed stainless steel reel bearings.

BEDKNIFE Bedknife is high carbon through-hardened steel. EdgeMaxTM Microcut Bedknife is standard on 11 & 14-blade cutting unit. EdgeMax bedknife is solid tool steel.

GRASS BASKET Molded polyethylene with integrated graphics highlighting overlap guidelines, vented for high-efficiency collection.

ROLLERS Front Roller: Optional – must be ordered. Rear Roller: Aluminum full roller 2” (5.1 cm) diameter with sealed bearings.

WORKING WEIGHT 293 lbs. (133 kg) w/basket, w/o transport tires and groomer.

CERTIFICATION /WARRANTY Designed in accordance to ANSI/CE/WEEE/ROHS/C-TICK. Two-year limited warranty. Years 3-5 prorated warranty on Lithium-Ion Battery. Refer to the Operator’s Manual for further details.

GREENSMASTER eFLEX 2120 ACCESSORIES


GROOMER OPTIONS04648 Universal Groomer Drive04802 Groomer Reel – Twin Tip04270 Greens Grooming Brush (21") – Soft04271 Greens Grooming Brush (21") – Stiff

CUTTING UNITS & REEL OPTIONS04290 11-Blade DPA Cutting Unit04292 14-Blade DPA Cutting Unit137-8511 11-Blade Edge SeriesTM Reel137-8517 8-Blade HD Reel

BEDKNIFE & BEDBAR OPTIONS93-4263 Tournament Bedknife93-4264 Low Cut Bedknife108-4303 Extended Microcut Bedknife93-4262 Microcut Bedknife108-4302 Extended Tournament Bedknife115-1881 EdgeMaxTM Tournament Bedknife137-0879 EdgeMaxTM Fairway Bedknife63-8610 Fairway Bedknife94-6392 High Height of Cut Bedknife120-9600 High Height of Cut Kit99-3794-03 Aggressive Bedbar

TRACTION UNIT ACCESSORIES04064 LED Light Kit04070 Battery04065 Battery Charger04266 Push Broom Brush04123 Wheel Kit

SCRAPER OPTIONS125-3503 Narrow Wiehle Roller Scraper125-3504 Wide Wiehle Roller Scraper125-3505 Full Roller Scraper115-7377 Narrow Wiehle Roller Scraper Brush115-7378 Wide Wiehle Roller Scraper Brush115-7379 Full Roller Scraper Brush115-7380 Narrow Wiehle Roller Scraper Comb115-7381 Wide Wiehle Roller Scraper Comb115-7382 Full Roller Scraper Comb115-7383 Rear Roller Scraper

ROLLER OPTIONS04255 Front Narrow Wiehle Roller04256 Front Wide Wiehle Roller04250 Split Narrow Wiehle Roller107-3514 Front Wide Wiehle Roller – Steel04257 Front Full Roller04249 Split Full Front Roller04258 Long Front Narrow Wiehle Roller04267 Paspalum Roller115-7356 Rear Full Roller – Aluminum120-9595 Rear Full Roller – Steel115-7361 Front Roller Extension Kit120-9602 Rear Roller Adjustment Kit

STANDARD CUTTING UNIT EQUIPMENT115-1880 EdgeMaxTM Microcut Bedknife106-2648-01 Less Aggressive Bed Bar

TOOLS04399 Turf Evaluator125-5610 Paper – Reel125-5611 Shim – Reel94-9010 Height of Cut Adjustment Bar131-6828 Angle Indicator131-6829 Angle Indicator Mount


Greensmaster® 800Uniquely weighted, front to rear, the Greensmaster 800 deeply penetrates the turf’s surface for a lower, more consistent height of cut,

and straight tracking. (This product will be discontinued April 2019.)




GREENSMASTER 800, MODEL 04054 (This product will be discontinued April 2019)



TRACTION AND IMPLEMENT DRIVE Engine to countershaft drive: two “A” section V-belts. Timing belts from countershaft to differential, drive drum and reel.

REEL DRIVE Positive drive belt powered reel. Manually activated jaw-type clutch provides drive engagement/disengagement.

GROUND SPEED Mowing speed: 1.5 mph (2.4 km/h) to 3.3 mph (5.3 km/h). Transport speed (maximum): 5.0 mph (8.0 km/h) with transport tires installed.

DIFFERENTIAL Peerless Series 100.

CLUTCHES Traction: inside belt idler. Reel: jaw type.

BRAKE Service/parking-band type.

TRACTION DRUM Dual cast aluminum, 7.5" (19 cm) diameter.

CONTROLSEngine mounted; recoil starter, choke, fuel shutoff. Handle mounted: hour meter, on/off switch, throttle lever, traction engage lever, service/park brake lever, on/off light switch (optional). Frame mounted: reel drive engage lever. Safety devices: neutral interlock system, servicing/park brake, enclosed drive system. Optional: Operator Presence Control.

HANDLE Loop style; 1" (2.5 cm) diameter with easy pull pin height adjustment, operator selected.

TRANSPORT TIRES/KICKSTAND Optional – Two quick detachable pneumatic tires, 3.00 x 3.25-6. 15 psi (1.03 bars) tire pressure. Lift assist kickstand is standard.

REEL CONSTRUCTION 5" (12.7 cm) diameter, 14 high-carbon steel blades welded to 5 stamped steel spiders. Optional 11-blade reel.


HEIGHT OF CUT .078" to 1.0" (1.98-25.4 mm)

CLIP Standard w/Clip Kit Standard 14-Blade: .13" (3.3 mm) .19" (4.9 mm)Optional 11-Blade: .16" (4.3 mm) .25" (6.4 mm)

BEDKNIFE/BEDBAR Dual screw “click” adjustment to reel. EdgeMaxTM Microcut Bedknife standard

GRASS BASKET Patented design: molded polyethylene, baffled and vented for high efficiency collection.

FRONT ROLLER Aluminum Wiehle roller standard; 2" (5.1 cm) diameter, .200 spacing.

WEIGHT 216 lbs. (97.9 kg) with aluminum Wiehle roller, kickstand and grass basket, without transport tires and groomer.

CERTIFICATION Designed in accordance to ANSI specifications B71.4-2012 and European Community (CE) specifications with required kits installed.



TRACTION UNIT ACCESSORIES112-9282 Operator Presence Bail Kit (ANSI/CE req.)

04266 Push Broom Brush

04123 Wheel Kit

115-1886 Traction Slow Down Kit

65-9000 Clip Kit

115-4754 Wireless Hour Meter (requires 04295)

117-0073 High Altitude Kit

04063 LED Light Kit

GREENSMASTER 800 ACCESSORIES

BEDKNIFE & BEDBAR OPTIONS117-1530 EdgeMaxTM Microcut Bedknife

98-7261 Microcut Bedknife

110-2300 Extended Microcut Bedknife

117-1532 EdgeMaxTM Tournament Bedknife

98-7260 Tournament Bedknife

110-2301 Low Cut Bedknife

120-2731-03 Bedbar – Aggressive

ROLLER & ROLLER SCRAPER OPTIONS99-6240 Narrow Wiehle Roller (Standard)

98-7264 Wide Wiehle Roller

104-2640 Full Roller

65-8560 Roller Extension

98-7257 Full Roller Scraper

121-2617 Wide Wiehle Scraper

99-6239-01 Narrow Wiehle Scraper

121-2616 Scraper Brush

GROOMING OPTIONS04134 Groomer Drive Reverse

125-3451 Forward Rotating Kit

120-2742 Grooming Brush

04268 Grooming Brush – Soft

04269 Grooming Brush – Stiff

04801 Grooming Reel – Twin Tip

REEL OPTIONS132-7353 11-Blade Reel

132-7354 14-Blade Reel (standard)

TOOLS04399 Turf Evaluator

125-5610 Paper – Reel

125-5611 Shim – Reel

94-9010 Height of Cut Bar Assembly

131-6828 Angle Indicator

131-6829 Mount-Angle Indicator


Greensmaster® 1000Uniquely weighted, front to rear, the Greensmaster 1000 deeply penetrates the turf’s surface for a lower, more consistent height of cut, and straight tracking. (This product will be discontinued February 2019 – Honda® engine will be introduced thereafter.)


* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only. Actual products offered for sale may vary in use, design, required attachments and safety features. Consult your local Toro Distributor. The Greensmaster 1000 is manufactured

in Tomah, WI ISO 9002 Certified Plant.

TRACTION UNIT ACCESSORIES04063 LED Light Kit

112-9282 Operator Presence Bail Kit (ANSI/CE req.)

04266 Push Broom Brush

04123 Wheel Kit


65-9000 Clip Kit


117-0073 High Altitude Kit



ROLLER OPTIONS88-6790 Wide Wiehle Roller

93-9045 Long Front Wiehle Roller 2.5" (63.5 mm) dia.

71-1550 Cast Iron Wiehle Roller

104-2642 Full Roller

65-8560 Front Roller Extension Kit

GROOMING OPTIONS04134 Reverse Groomer Drive




04802 Grooming Reel – Twin Tip

SCRAPER OPTIONS112-9285 Smooth Scraper

112-9288 Wide Wiehle Roller Scraper

112-9286 Scraper Brush

112-9289 Narrow Wiehle Roller Scraper

112-9287 Scraper Comb

BEDKNIFE & BEDBAR OPTIONS115-1880 EdgeMaxTM Microcut Bedknife (standard)

93-4262 Microcut Bedknife




108-4302 Extended Tournament Bedknife


112-7475 EdgeMax Fairway Bedknife

63-8600 Fairway Bedknife

94-6392 High Cut Bedknife

112-9279-03 Bedbar – Aggressive

REEL OPTIONS132-7312 8-Blade Reel


132-7314 14-Blade Reel

04109 Dethatching Reel









TRACTION DRIVE Positive drive belt driven split drums through a differential. Two "A" section v-belts with manually activated idler pulley provide drive engagement/disengagement. Gear reduction ratio (2:1), mounted to engine.





BRAKE Service/parking-band type.

TRACTION DRUM Dual cast aluminum, 7.5" (19 cm) diameter.

CONTROLSEngine mounted; recoil starter, choke, fuel shut-off. Handle mounted: hour meter, on/off switch, throttle lever, traction engage lever, service/park brake lever, on/off light switch (optional). Frame mounted: reel drive engage lever. Safety devices: neutral interlock system, servicing/park brake, enclosed drive system. Optional: Operator Presence Control.


TRANSPORT TIRES/KICKSTAND Optional – Two quick detachable pneumatic tires, 3.00 x 3.25-6. 15 psi (1.03 bars) tire pressure. Lift assist kickstand is standard.

REEL CONSTRUCTION 5" (12.7 cm) diameter, 11 high-carbon steel blades welded to 5 stamped steel spiders. Optional 8-blade & 14-blade reel.


HEIGHT OF CUT .078" to 1.0" (1.98-25.4 mm)

CLIP Standard w/Clip Kit Standard 11-Blade: .16" (4.3 mm) .25" (6.4 mm) Optional 8-Blade: .23" (5.8 mm) .34" (8.6 mm) Optional 14-Blade: .13" (3.3 mm) .19" (4.9 mm)

BEDKNIFE/BEDBAR Dual screw “click” adjustment to reel. EdgeMaxTM Microcut Bedknife standard

GRASS BASKET Patented design: molded polyethylene, baffled and vented for high efficiency collection.

FRONT ROLLER Aluminum Wiehle roller standard; 2" (5.1 cm) diameter, .200 spacing.

WEIGHT 220 lbs. (99.8 kg) with aluminum Wiehle roller, kickstand and grass basket, without transport tires and groomer.

CERTIFICATION Designed in accordance to ANSI specifications B71.4-2017 and European Community (CE) specifications with required kits installed.



Greensmaster® 1600Its wider 26" cut and extended height of cut range offers greater productivity. Ideal for tees, aprons, even large greens. (This product will be discontinued April 2019.)




GREENSMASTER 1600, MODEL 04056



TRACTION AND IMPLEMENT DRIVE Engine to countershaft drive: two “A” section V-belts. Timing belts from countershaft to differential, drive drum and reel.





BRAKE Servicing brake; band type.

TRACTION DRUM Dual cast aluminum. 7.5" (19 cm) diameter.

CONTROLS Engine mounted: recoil starter, choke, fuel shut-off. Handle mounted: Hour meter, on/off switch, throttle lever, traction engage lever, service/part brake lever, on/off light switch (optional). Frame mounted: reel drive engage lever. Safety devices: neutral interlock system, servicing/park brake, enclosed drive system.


TRANSPORT/TIRES/ KICKSTAND Optional – Two quick detachable pneumatic tires, 3.00 x 3.25-6. 15 psi (1.03 bar) tire pressure. Lift assist kickstand is standard.

REEL CONSTRUCTION 5" (12.7 cm) diameter, 8 high carbon steel blades welded to 6 stamped steel spiders. Optional 11-blade reel.


HEIGHT OF CUT .125"-1.25" (3.2 -31.8 mm)

CLIP Standard w/Clip Kit Standard 8-Blade: .23" (5.8 mm) .34" (8.6 mm) Optional 11-Blade: .17" (4.3 mm) .25" (6.4 mm)

BEDKNIFE/BEDBAR Dual screw “click” adjustment to reel. Low-cut bedknife standard.

GRASS BASKET Molded polyethylene. 2 position.

FRONT ROLLER Aluminum Wiehle roller standard; 2" (5.1 cm) diameter, .200" spacing.

DIMENSIONS Overall Length Overall Width Overall Height Weight 59" (150 cm) 41" (104 cm) 48" (122 cm) w/o transport tires 232 lbs. (146.5 kg) w/o transport tires

CERTIFICATION Designed in accordance to ANSI specifications, B71.4-2012 and European Community (CE) specifications with required kits.



TRACTION UNIT ACCESSORIES04063 LED Light Kit

112-9282 Operator Presence Bail Kit (ANSI/CE req.)


65-9000 Clip Kit

04123 Wheel Kit

117-0073 High Altitude Jet


ROLLER & ROLLER SCRAPER OPTIONS95-0930 Full Roller

65-8560 Front Roller Extension Kit

112-9290 Wiehle Roller Scraper

BEDKNIFE & BEDBAR OPTIONS112-9275 Microcut Bedknife





112-9278-03 Bedbar - Aggressive (Black)

99-4286 High Height of Cut Arm

STANDARD EQUIPMENT93-9039 Narrow Wiehle Roller

112-9280-01 Bedbar - Standard (Red)



REEL OPTION132-7362 11-Blade Reel

GROOMING OPTIONS04134 Reverse Groomer Drive



04803 Grooming Reel – Twin Tip TOOLS04399 Turf Evaluator







TransPro® 80 & 100Safely and easily transports one or two walk greensmowers to and from the green.

TRANSPRO 80, MODEL 04238* TRANSPRO 100, MODEL 04240*LOAD CAPACITY 400 lbs. (181.6 kg) including weight of trailer. 800 lbs. (363 kg) including weight of trailer.

SUSPENSION Large low pressure tires (20 x 10-8).

TRANSPORT SPEED Maximum of 15 mph (24 km/h).

RAMP Quick latch to secure loading ramp during transport. Rubber mats to protect front roller. Flat Ramp Kit or Rail or Ramp Kit required.

Quick latch to secure loading ramp during transport. Rubber to protect front roller and provide safe surface during loading unloading of Greensmaster. High Rail Ramp Kit optional.

HITCH Pin type hitch is standard; tongue is 2.5" (6.4 cm) wide and adjustable in length (will accept standard ball hitch).

Pin type hitch is standard; tongue is 2" (5 cm) wide and adjustable in length (will accept standard ball hitch).

TOWING Designed to tow behind a utility vehicle; tongue height 7"-13" (18-33 cm); maximum tongue load 55 lbs. (25 kg). Incorporates a tongue stand and tongue lift handle.

BED Hold down bails fold around mower tires to during transport. Drain holes in trailer bed for greensmower on trailer, allowing water and trailer floor.

FINISH Rust/corrosion-resistant paint.

AXLES Heavy-duty stub. Greaseable.

DIMENSIONSHeight: 19" (48.3 cm) Width: 62" (157.5 cm) Length: 81" (205.7 cm)

Height: 36" (91.4 cm) Width: 60.5" (153.7 cm) Length: 101" (256.5 cm)

Easily adjustable to fit all Toro walk greensmowers.For 21" mowers with transport tires (standard), conversion kits available for 18" mowers. Rail kits available for both 18" and 21" mowers. Not recommended for Greensmaster® 1600.

TRANSPRO 80 ACCESSORIES TRANSPRO 100 ACCESSORIES04245 Flat Ramp Kit 04248 Rail Ramp Conversion Kit (RoHS Compliant)

04247 Rail Ramp Kit 110-7355 18" Transport Wheel Conversion Kit

107-8188 Hitch Kit 110-7345 18" Rail Conversion Kit

136-7287 Extended Axle for Rail Ramp Using 04648 Groomer 136-8548 Flex 21" Retrofit Kit for 04648 Groomer (does not work with rail ramp)

136-8551 Flex 18" Retrofit Kit for 04648 Groomer (does not work with rail ramp)



Greensmaster® 3120The Greensmaster 3120 delivers the quality cutting performance you expect from a Toro. Equipped with patented DPA cutting units for a superior cut and minimal maintenance, convenient controls for easy operation, and power to handle any application – it’s nowonder the 3120 delivers the performance golf courses demand. And it's easy on your budget too.





8 BLADE DPA CUTTING UNITS 11-BLADE DPA CUTTING UNITS 14-BLADE CUTTING UNITSTRACTOR These cutting units will mount on any Toro riding Greensmaster (excluding Greensmaster TriFlexTM 33xx/34xx series).

HEIGHT OF CUT (HOC) RANGE

Cutting height is adjusted on front roller by two vertical screws and held by two locking cap screws. Bench HOC range is .062"-.297" (1.6-7.5 mm). With high HOC kit, range is .285-1" (7.3-25.4 mm). Effective HOC may vary depending on turf conditions and bedknife installed.

REEL WELDMENT Reels are 5" (13 cm) in diameter, 21" (53.3 cm) in length. EdgeSeries™ Reels are welded to 5 stamped steel spiders, and heat treated. The reel is ground for diameter and concentricity, and relief ground.

REEL BEARINGS Two stainless steel ball bearings, 30 +/-.1 mm inside diameter slip fit onto reel shaft retained by internally splined threaded insert. Low drag seals/slingers for added protection with o-ring sealed motor and counterweight. Reel position maintained by a wave washer with no adjusting nut.

MAINTENANCE No grease zerks, sealed bearing design eliminates daily maintenance.

REEL DRIVE The reel weldment shaft is a 1.375" (35 mm) diameter tube with internally splined threaded insert.

FRAME Precision machined, die-cast aluminum cross member with two bolt-on die-cast aluminum side plates.

AGGRESSIVENESS Aggressiveness stays constant throughout the life of the reel. Patented design.

BEDKNIFE Replaceable single edged EdgeMaxTM Microcut Bedknife is standard.

BEDKNIFE ADJUSTMENT Dual screw, indexed “click” adjustment to the reel; detents corresponding to .0007" (.018 mm) bedknife movement for each position.

FRONT & REAR ROLLERS Front: Not included with cutting unit, purchased separately. Option between full, narrow-spaced and wide-spaced Wiehle roller. Rear: Steel full, 2" (5.1 cm) diameter with sealed bearings and through-shaft.

GRASS SHIELD Non-adjustable shield with adjustable cut-off bar to improve grass discharge from reel in wet conditions.

TOTAL WEIGHT 8-blade: 72 lbs. (32.7 kg) with aluminum Wiehle Roller. 11-blade: 75 lbs. (34 kg) with aluminum Narrow Wiehle Roller. 14-blade: 78 lbs. (35 kg) with aluminum Wiehle Roller.

GREENSMASTER 3120, MODEL 04355ENGINE 16 hp (11.9 kW) @3600 rpm, Briggs & Stratton® gasoline engine, governed to 2850 rpm high idle, 1650 rpm low idle. Air-cooled.

FUEL CAPACITY 7 gallon (26.5 liter) capacity; unleaded gasoline.

TRACTION DRIVE Hydraulic piston pump, closed loop system. 2WD Parallel Hydrostatic. Foot pedal forward and reverse; infinitely variable.

GROUND SPEEDForward-mowing speed is variable from 2-5 mph (3.2-8 km/h), adjusted by stop on pedal mechanism. Mow speed setting does not affect transport speed. Maximum Greensmaster 3120 transport speed is 7.0 mph (11.3 km/h), may be reduced by adjusting stop in footrest pan without affecting mow speeds. Reverse is 2.5 mph (4.0 km/h) maximum.

TURF COMPACTION 8-10 psi (dependent on tire pressure) with operator and cutting units down.

IMPLEMENT DRIVE Single gear pump, mono valve block, series reel drive to 3 motors.

STEERING Power steering. Adjustable steering wheel tilt and a 5-position steering arm tilt.

CONTROLS/GAUGES Raise/lower-mow lever (joystick). Functional control lever (neutral, mow, transport). Foot operated traction drive and brakes. Hour meter. Hand operated throttle and choke. Mechanical engine speed control.

ELECTRICAL FEATURES 12-volt lead acid, group size U1, with 300 minimum cold cranking amps at 0° F and 34 minutes reserve capacity at 85° F/25 amps draw. 16 amp alternator. Ignition switch/key. Seat switch. Harness terminals and fuse slot available for optional lights installation.

TIRES/WHEELS/PRESSURE Three tires: Three 18 x 10.5-8, 4-ply pneumatic tubeless demountable and interchangeable with smooth tread. 8-12 psi front; 8-15 psi rear. Optional Traction Tire (4-ply): P/N 119-3516.

BRAKES Two 6" (15.2 cm) drum type.

HYDRAULIC OIL 5.0 gallon (18.9 liter) tank with internal baffle. 1.0 gallon (3.8 liter) auxiliary tank.

SOUND LEVEL 82 dB(A) at operator’s ear under normal conditions.

OVERALL DIMENSIONS Wheel Tread: 49.5" (149.9 cm), Wheel Base: 47" (119 cm), Length: 90" (229 cm), Width: 69.7" (177 cm) w/reels, Height: 74.5" (189 cm), Weight: 1,087 lbs. (493 kg).


REEL SPEED Approximately 1975 RPM at 2850 engine RPM.

BACKLAPPING Standard equipment.

CUTTING UNIT SUSPENSION Cutting units are completely free-floating, each attaching to the tractor by direct pull links and lifted by a centered lift arm. Baskets are supported by carrier frames that are ground following. Cutting unit floatation is unaffected by basket content. Grass baskets are all interchangeable and accessible from the front of the machine.

ROPS Roll Over Protection System standard.

CERTIFICATION Certified to meet ANSI specification B71.4-2012.




Greensmaster® 3120 Accessories*

THATCHING REEL ACCESSORIES

117-6824 Thin dynaBLADE, (1.2mm Thickness)(Individual)

119-1128 Regular dynaBlade, (2mm Thickness)(Individual)

117-6839 Replacement Kit, 1.2mm dynaBlade (36 Blades)

117-6840 Replacement Kit, 2mm dynaBlade (36 Blades)

121-6675 Spring Steel Kit

121-6674 Blade, Spring Steel

121-9525 Thatching Reel Quick Change Kit

GROOMER OPTIONS04648 Universal Groomer Drive (Set of 1)

04802 Groomer Reel



106-2643 Groomer Pull Link Kit

SCRAPER OPTIONS125-5303 Front Narrow Wiehle Roller Scraper

125-5304 Front Wide Wiehle Roller Scraper

125-5305 Front Full Roller Scraper

115-7377 Front Narrow Wiehle Roller Scraper Brush

115-7378 Front Wide Wiehle Roller Scraper Brush

115-7379 Front Full Roller Scraper Brush

115-7380 Front Narrow Wiehle Roller Scraper Comb

115-7381 Front Wide Wiehle Roller Scraper Comb

115-7382 Front Full Roller Scraper Comb

115-7383 Rear Roller Scraper

121-2260 Adjustable Rear Roller Scraper

04646 Spring Loaded Rear Roller Scraper (Set of 3)

107-9561 Anti-Bobbing Roller Scraper Kit

04650 Rotating Rear Roller Brush (LH) (Set of 1)








115-1880 EdgeMaxTM Microcut Bedknife (Standard)


112-7475 EdgeMaxTM Fairway Bedknife

106-2648-01 Bedbar (Standard)

99-3794-03 Aggressive Bedbar

CUTTING UNIT & REEL OPTIONS04652 8-Blade Cutting Unit

04654 11-Blade Cutting Unit


121-6651 8-Blade Reel, Heavy-Duty (Individual)


BIO-HYDRAULIC FLUID / HYDRAULIC FLUID / OIL119-2157 Bio-Hydraulic Fluid, 5 gal. (18.9 L)

119-2158 Bio-Hydraulic Fluid, 55 gal. (208.2 L)

108-1178 Premium Hydraulic Fluid, 5 gal. (18.9 L)


108-1197 Premium Engine Oil SAE 30, 5 gal. (18.9 L)






TRACTION UNIT ACCESSORIES04495 Greens Tri-Roller Kit

30707 Armrest Kit

119-3516 Traction Tires

04554 Light Kit

130-6536 Hydraulic Oil Cooler Kit

108-6472 Traction Speed Control Kit

104-6540 Spark Arrestor Screen

115-4510 Bimini Folding Shade

100-6442 2WD Weight Kit

115-4754 Wireless Hour Meter

ROLLER OPTIONS04626 Front Narrow Wiehle Roller (set of 3)

04627 Front Wide Wiehle Roller (set of 3)

04625 Front Full Roller (set of 3)

04628 Solid Steel Roller Kit (front Wiehle & rear steel rollers)

04629 Anti-Bobbing Roller

71-1550 Cast Iron Rear Wiehle Roller

107-3514 Steel Wide Wiehle Roller

121-4675 Extended Wiehle Roller

04258 Extended Narrow Wiehle Roller

04267 Narrow Wiehle Roller (for paspalum)

107-3510 Steel Narrow Wiehle Roller

120-9595 Steel Rear Roller (standard)

125-5180 DPA Rear Roller Extension Kit

120-9600 High Height of Cut Kit

04249 Split Full Front Roller

04250 Split Narrow Wiehle Roller


Greensmaster® 3150-QThe Greensmaster 3150-Q is distinguished for its field-proven performance and exceptional quality of cut. Equipped with patented DPA cutting units for a superior cut and minimal maintenance, convenient controls for easy operation, and ample power to handle any application – it’s no wonder this classic model has been trusted over the years to deliver the performance golf courses demand with a putting surface that exceeds expectations.

622019 Toro Commercial Equipment Guide 19-003-T Rev. 6/19The Greensmaster 3150-Q is manufactured in Tomah, WI ISO 9002 Certified Plant.

Greensmaster® 3150-Q Specifications*

* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only. Actual products offered for sale may vary in use, design, required attachmentsand safety features. Consult your local Toro Distributor.

8 BLADE DPA CUTTING UNITS 11-BLADE DPA CUTTING UNITS 14-BLADE CUTTING UNITSTRACTOR These cutting units will mount on any Toro riding Greensmaster (excluding Greensmaster TriFlexTM 33xx/34xx series).


Cutting height is adjusted on front roller by two vertical screws and held by two locking cap screws. Bench HOC range is .062"-.297" (1.6-7.5 mm). With high HOC kit, range is .297-1.0" (7.5-25.4 mm). Effective HOC may vary depending on turf conditions and bedknife installed.

REEL WELDMENT Reels are 5" (13 cm) in diameter, 21" (53.3 cm) in length. EdgeSeries™ Reels blades are welded to 5 stamped steel spiders, and heat treated. The reel is ground for diameter and concentricity, and relief ground.

REEL BEARINGS Two stainless steel ball bearings, 30 +/-.1 mm inside diameter slip fit onto reel shaft retained by internally splined threaded insert. Low drag seals/slingers for added protection with o-ring sealed motor and counterweight. Reel position maintained by a wave washer with no adjusting nut.






BEDKNIFE ADJUSTMENT Dual screw, indexed “click” adjustment to the reel; detents corresponding to .0007" (.018 mm) bedknife movement for each position.



TOTAL WEIGHT 8-blade: 72 lbs. (32.7 kg) with aluminum Wiehle Roller. 11-blade: 75 lbs. (34 kg) with aluminum Narrow Wiehle Roller.14-blade: 78 lbs. (35 kg) with aluminum Wiehle Roller.

GREENSMASTER 3150-Q, MODEL 04358ENGINE 18 hp (13.4 kW) @3600 rpm, Briggs & Stratton® gasoline engine, governed to 2850 rpm high idle, 1650 rpm low idle. Air-cooled.

FUEL CAPACITY 7 gallon (26.5 liter) capacity; unleaded gasoline.

TRACTION DRIVE Hydraulic piston pump, closed loop system. 2WD Parallel Hydrostatic or 3WD Series Parallel piston pump closed loop system. Foot pedal forward and reverse; infinitely variable.

GROUND SPEEDForward-mowing speed is variable from 2-5 mph (3.2-8 km/h), adjusted by stop on pedal mechanism. Mow speed setting does not affect transport speed. Maximum Greensmaster 3150-Q transport speed is 8.8 mph (14.4 km/h), may be reduced by adjusting stop in footrest pan without affecting mow speeds. Reverse is 2.5 mph (4.0 km/h) maximum.

TURF COMPACTION 8-12 psi (.55-.83 bar) (dependent on tire pressure) with operator and cutting units down.

IMPLEMENT DRIVE Single gear pump, mono valve block, series reel drive to 3 motors.

STEERING Power steering. Adjustable steering wheel tilt and a 5-position steering arm tilt.

CONTROLS/GAUGES Raise/lower-mow lever (joystick). Functional control lever (neutral, mow, transport). Foot operated traction drive and brakes. Hour meter. Hand operated throttle and choke. Mechanical engine speed control.

ELECTRICAL FEATURES 12-volt lead acid, group size U1, with 300 minimum cold cranking amps at 0° F. 16 amp alternator. Ignition switch/key. Seat switch. Harness terminals and fuse slot available for optional lights installation.

TIRES/WHEELS/PRESSURE Three tires: Three 18 x 10.5-8, 4-ply pneumatic tubeless demountable and interchangeable with smooth tread. 8-12 psi front; 8-15 psi rear. Optional Traction Tire (4-ply): P/N 119-3516.

BRAKES Two 6" (15.2 cm) drum type.

HYDRAULIC OIL 7.5 gallon (28.4 liter) tank with internal baffle. 1.0 gallon (3.8 liter) auxiliary tank.

LEAK DETECTION Equipped with Turf Guardian™ leak detection system.

SOUND LEVEL 82 dB(A) at operator’s ear under normal conditions.

OVERALL DIMENSIONS Wheel Tread: 49.5" (149.9 cm), Wheel Base: 47" (119 cm), Length: 90" (229 cm), Width: 69.7" (177 cm) w/reels, Height: 74.5" (189 cm), Weight: 1,087 lbs. (493 kg).


REEL SPEED Approximately 1975 RPM at 2850 engine RPM. Adjustable.


CUTTING UNIT SUSPENSION Cutting units are completely free-floating, each attaching to the tractor by direct pull links and lifted by a centered lift arm. Baskets are supported by carrier frames that are ground following. Cutting unit floatation is unaffected by basket content. Grass baskets are all interchangeable and accessible from the front of the machine.

ROPS Roll Over Protection System standard.

CERTIFICATION Certified to meet ANSI specification B71.4-2012 and European CE standards with appropriate kits installed.


632019 Toro Commercial Equipment Guide 19-003-T Rev. 1/19The Greensmaster 3150-Q is manufactured in Tomah, WI ISO 9002 Certified Plant.


Greensmaster® 3150-Q Accessories*

TRACTION UNIT ACCESSORIES04476 3-Wheel Drive Kit

04479 Thatching Reel (Set of 1)

04495 Greens Tri-Roller Kit

30707 Armrest Kit


04554 Light Kit


108-6472 Traction Speed Control Kit

104-6540 Spark Arrestor Screen





















THATCHING REEL ACCESSORIES117-6824 Thin dynaBlade, (1.2mm Thickness)(Individual)








04802 Groomer Reel

















04650 Rotating Rear Roller Brush (Set of 1)
















119-4103 8-Blade Reel (Individual)




GREENSMASTER 3150-Q ACCESSORIES












Greensmaster® 3250-DUnmatched diesel power, innovative design and a lighter footprint make this the ideal greensmower for greens and surrounding areas.

652019 Toro Commercial Equipment Guide 19-003-T Rev. 6/19The Greensmaster 3250-D is manufactured in Tomah, WI ISO 9002 Certified Plant.

Greensmaster® 3250-D Specifications*


GREENSMASTER 3250-D, MODEL 04384

ENGINE Kubota® 902 tier 4i, 3-cylinder liquid-cooled diesel engine. 55.0 cu. in. (902 cc). Full pressure lubrication, oil filter. 24.8 hp (18.5 kW) @ 3600 rpm. Engine governed to 2760 rpm high idle, 1500 rpm low idle (no load).

FUEL CAPACITY 6 gallons (22.7 liters). Biodiesel-Ready for use up to B-20 (20% biodiesel and 80% petroleum blend).

TRACTION DRIVE Hydraulic piston pump, closed loop system. 2WD Parallel Hydrostatic or 3WD Series Parallel piston pump closed loop system. Foot pedal forward and reverse; infinitely variable.

GROUND SPEEDForward-mowing speed is variable from 2-5 mph (3.2-8 km/h), adjusted by stop on pedal mechanism. Mow speed setting does not affect transport speed. Maximum Greensmaster 3250-D transport speed is 8.8 mph (14.4 km/h), may be reduced by adjusting stop in footrest pan without affecting mow speeds. Reverse is 2.5 mph (4.0 km/h) maximum.

TURF COMPACTION 8-12 psi (.55-.83 bar) average at recommended minimum tire pressures, with a 200 lb.. operator, and cutting units down.

STEERING Power steering. No-tool quick adjust steering arm position, with arm motion allowing a wide range of operator sizes. Steering cylinder has through shaft design for accurate straight line steering.

CONTROLS/GAUGES Raise/lower-mow lever. Functional control lever (neutral, mow, transport). Foot operated traction drive and brakes. Hour meter and 4 bulb warning cluster. Hand operated choke, throttle. Mechanical engine speed control.

ELECTRICAL FEATURES Maintenance-free 12-volt battery with 530 minimum cold cranking amps at 0° F. 40 amp alternator, circuit fused at 40 amps. Ignition switch/key. Seat switch. High temperature engine kill override switch. Harness terminals, fuse slot, and console switch location available for optional lights installation.

SOUND LEVEL 84 dBA at operator ear under normal conditions.

OVERALL DIMENSIONS

Width of Cut: 59.0" (150 cm) Overall Height: 77.5" (197 cm) Wheel Tread: 50.5" (128 cm) Net Weight (no fuel, no operator): 1,216 lbs. (552 kg) Wheel Base: 48.6" (123 cm) Reel Speed: Approx.1,950 rpm @ 2760 rpm (Adjustable) Overall Length (w/baskets): 93.9" (238 cm) Overall Width: 68.0" (173 cm)

TIRES Three 19 x 10.5-8, 2 ply pneumatic tubeless demountable and interchangeable. Smooth tread (approx. 1290 rev/mile). 8-12 psi front; 8-15 psi rear.

LEAK DETECTION Turf Guardian™ optional.


BRAKES 6" (15.2 cm) drum type mechanical with rack and pawl lock for parking.

SEAT Contour seat with high backrest. 7" (17.8 cm) fore/aft slider adjustment with two mounting positions, allowing 9" (22.8 cm) total seat travel. Operator manual tube mounted on the seat back for easy access.

ROPS Roll over protection system standard.

CERTIFICATION Certified to meet ANSI specification B71.4-2012 and European CE standards with appropriate kits installed.


8 BLADE DPA CUTTING UNITS 11-BLADE DPA CUTTING UNITS 14-BLADE CUTTING UNITSTRACTOR These cutting units will mount on any Toro riding Greensmaster (excluding Greensmaster TriFlex 33xx/34xx series).

HEIGHT OF CUT (HOC) RANGE Cutting height is adjusted on front roller by two vertical screws and held by two locking cap screws. Bench HOC range is .062"-.297" (1.6-7.5 mm). With high HOC kit, range is .297-1.0" (7.5-25.4 mm). Effective HOC may vary depending on turf conditions and bedknife installed.

REEL WELDMENT Reels are 5" (13 cm) in diameter, 21" (53.3 cm) in length. EdgeSeries™ Reels blades are welded to 5 stamped steel spiders, and heat treated to RC 48-54 hardness. The reel is ground for diameter and concentricity, and backgrind.

REEL BEARINGS Two stainless steel ball bearings, 30 mm inside diameter slip fit onto reel shaft retained by internally splined threaded insert. Low drag seals/slingers for added protection with o-ring sealed motor and counterweight. Reel position maintained by a wave washer with no adjusting nut.






BEDKNIFE ADJUSTMENT Dual screw, indexed “click” adjustment to the reel; detents corresponding positively to .0007" (.018 mm) bedknife movement for each position.

FRONT & REAR ROLLERS Front: Not included with cutting unit, purchased separately. Option between full, narrow-spaced and wide-spaced roller. Rear: Steel full, 2" (5.1 cm) diameter with sealed bearings and through-shaft.


TOTAL WEIGHT 8-blade: 72 lbs. (32.7 kg) with aluminum Wiehle Roller. 11-blade: 75 lbs. (34 kg) with aluminum Narrow Wiehle Roller. 14-blade: 78 lbs. (35 kg) with aluminum Wiehle Roller.



The Greensmaster 3250-D is manufactured in Tomah, WI ISO 9002 Certified Plant.

Greensmaster® 3250-D Accessories*

GREENSMASTER 3250-D ACCESSORIES

TRACTION UNIT ACCESSORIES04477 3-Wheel Drive Kit

04479 Thatching Reel (Set of 1)

04495 Greens Tri-Roller Kit

30707 Armrest Kit



04554 Light Kit

120-1951 Spark Arrestor

04497 Leak Detector

112-0279 Front Wheel Weight Kit



100-6430 Hose Adapter Kit

105-9766 Radiator Screen Kit

104-9400 Ground Follow Kit



















THATCHING REEL ACCESSORIES

117-6824 Thin dynaBLADE, (1.2mm Thickness)(Individual)








04802 Groomer Reel

















04650 Rotating Rear Roller Brush (Set of 1)
























121-6393 Premium Engine Oil SAE 10W30, 5 gal. (18.9 L)

121-6392 Premium Engine Oil SAE 10W30, 55 gal. (208.2 L)






Greensmaster® TriFlex™ 3300/3320 Hybrid 3400/3420 HybridThe Greensmaster TriFlex and TriFlex Hybrid models are the first riding greens mowers delivering the productivity of a rider and the precision of a walker.

682019 Toro Commercial Equipment Guide 19-003-T Rev. 1/19The Greensmaster® TriFlexTM is manufactured in Tomah, WI ISO 9002 Certified Plant.

Greensmaster® TriFlex® 3300/3320/3400/3420 Specifications*


GREENSMASTER 3300 TriFlex, MODEL 04510

GREENSMASTER 3320 TriFlex Hybrid, MODEL 04530

GREENSMASTER 3400 TriFlex, MODEL 04520

GREENSMASTER 3420 TriFlex Hybrid, MODEL 04540

ENGINEBriggs & Stratton® Vanguard®, 21 HP (15.6 kW) @ 3600 rpm, 2-cylinder, air cooled, gasoline engine, governed to 2920 high idle, 1650 rpm low idle. Displacement: 38.3 cu-in. (627 cc)

Kubota® D902, Tier 4i, 24.8 HP (18.5 kW) @ 3600 rpm, 3-cylinder, liquid cooled, diesel engine, governed to 2880 high idle, 1560 rpm low idle. Displacement: 55.0 cu-in. (902 cc) Radiator: cooled with a 12-volt electric fan

FUEL CAPACITY 6 gallons (22.7 liter) capacity. 6 gallons (22.7 liter) capacity. Biodiesel ready up to B20

TRACTION DRIVE 2WD parallel hydrostatic or 3WD series-parallel piston pump closed loop system. Foot pedal forward and reverse; infinitely variable.

GROUND SPEEDForward-mowing speed is variable from 0-5 mph (0-8 km/h), adjusted by stop on pedal mechanism. Mow speed setting does not affect transport speed. Maximum Greensmaster TriFlex transport speed is 10 mph (16.1 km/h), may be reduced by adjusting stop in footrest pan without affecting mow speeds. Reverse is 3 mph (4.8 km/h) maximum.

CUTTING UNIT DRIVE Single gear pump, valve block, series reel drive to 3 reel motors.

48V-5400 watt air-cooled brushless permanent magnet generator in parallel with 48V 9Ah battery set powers three 48V- 1100 watt brushless permanent magnet reel motors.

Single gear pump, valve block, series reel drive to 3 reel motors.

48V-5400 watt air-cooled brushless permanent magnet generator in parallel with 48V 9Ah battery set powers three 48V- 1100 watt brushless permanent magnet reel motors.

AUTOMATIC CLIP CONTROL N/A Yes N/A Yes

STEERING Power steering. No-tool quick adjust steering arm position with power assist, with arm motion allowing a wide range of operator sizes. Steering cylinder has a through shaft design for accurate straight line steering.

ELECTRICAL SYSTEM12-volt lead acid, group size U1, with 300 minimum cold cranking amps at 0° F and 34 minutes reserve capacity at 85° F/25 amps draw. 50 amp alternator. Ignition switch/key. Seat switch. Harness terminals and fuse slot available for optional lights installation.

Maintenance-free 12-volt battery with 585 minimum cold cranking amps at 0° F (-17.7° C) and 95 minutes minimum reserve capacity at 85° F (29.4° C) 60 amp alternator, circuit fused at 60 amps. Ignition switch/key. Seat switch. High temperature engine shut down. Harness terminals, fuse slot, and console switch location available for optional lights installation.

48-VOLT SYSTEM FOR ELECTRIC REELS N/A

4-12V 9Ah sealed, maintenance-free, VRLA batteries. 48-volt system is isolated from 12-volt including the frame/chassis.

N/A4-12V 9Ah sealed, maintenance-free, VRLA batteries. 48-volt system is isolated from 12-volt including the frame/chassis.

CONTROLSIgnition: Off/Run/Start. Throttle: Low - High Idle. Choke (AC only): Open /Closes choke plate. Parking Brake: Off - On. Traction Pedal: Rev/Neutral/Forward Joystick: Raises/lowers reels also tap off feature for clean up pass. Functional Control Lever sets neutral/mow/transport limits for traction pedal. Diagnostic Light: Indicates system faults to assist in resolving issues (04510 & 04520). InfoCenterTM Diagnostics (04530 & 04540).

GAUGESFuel and hydraulic sight gauges, hour meter. Low oil pressure warning light.

Fuel and hydraulic sight gauges. InfoCenter™: Onboard LCD display shows gauges, alerts/faults, service reminders, electrical system diagnostics, low oil pressure, alternator, engine hours, engine rpm, voltage, functional control status, parking brake applied, reel speed setting, backlap control. New clip selection feature.

Fuel and hydraulic sight gauges, hour meter. Low oil pressure warning light, alternator warning light (on if not charging), glow plug indicator, high engine temperature.

Fuel and hydraulic sight gauges. InfoCenter™: Onboard LCD display shows gauges, alerts/faults, service reminders, electrical system diagnostics, low oil pressure, alternator, engine hours, engine rpm, voltage, functional control status, parking brake applied, reel speed setting, backlap control. New clip selection feature.

TIRES/WHEELS/PRESSURE Three, 19 x 10.5 x 8, 4-ply rating pneumatic tubeless and demountable. Smooth tread. Tire pressure recommended: 12 - 18 psi front and rear.

BRAKES Hand-actuated parking brake lever with two 6” (15.2 cm) diameter drum brakes mounted on the front wheel motors.

HYDRAULIC OIL 6.8 gallon (25.7 liter) tank 5.5 gallon (20.8 liter) tank 6.8 gallon (25.7 liter) tank 5.5 gallon (20.8 liter) tank

LEAK DETECTION

Equipped with Turf GuardianTM Leak Detection System. System sounds an alarm and turns on a warning light with the loss of 3 to 5 ounces of hydraulic oil.

Optional

SOUND LEVEL 80 dB(A) at operator’s ear under normal conditions. 84 dB(A) at operator’s ear under normal conditions.

OVERALL DIMENSIONS

Wheel Tread: 50.5" (128.3 cm) Wheel Base: 47" (119 cm) Length: 98" (249 cm) Width: 70.62" (179 cm) w/reels Height: 80.83" (205 cm)

Wheel Tread: 50.5” (128.3 cm)Wheel Base: 47” (119 cm)Length: 98” (249 cm) Width: 70.84” (180 cm) w/reels Height: 80.83” (205 cm)

Wheel Tread: 50.5” (128.3 cm) Wheel Base: 48.6” (123 cm) Length: 98” (249 cm) Width: 70.62” (179 cm) w/reels Height: 80.83” (205 cm)

Wheel Tread: 50.5” (128.3 cm)Wheel Base: 48.6” (123 cm)Length: 98” (249 cm) Width: 70.84” (180 cm) w/reels Height: 80.83” (205 cm)

WEIGHT 1161 lbs. (526 kg) 1257 lbs. (570 kg) 1286 lbs. (586 kg) 1406 lbs. (638 kg)


GROUND CLEARANCE 4.5” (11.4 cm)

CUTTING UNIT SUSPENSION Double A-arm suspension utilizing sealed ball joints allows free cutting unit motion in pitch, roll, and yaw. The basket is directly mounted to the cutting unit displacing weight evenly over both cutting unit rollers eliminating the carrier frame, roller and pull links.

QUICK CONNECT CUTTING UNITS Quick connect/disconnect feature for both the reel drive motor and cutting unit. No tools required.

REEL SPEED Approximately 2050 RPM at 2850 engine RPM. Adjustable.


OPTIONAL ACCESSORIES Canopy, verticutters, greens rollers, dethatchers, oil cooler.

CERTIFICATION Certified to meet ANSI specification B71.4 - 2004 and European CE standards.


692019 Toro Commercial Equipment Guide 19-003-T Rev. 1/19The Greensmaster® TriFlexTM is manufactured in Tomah, WI ISO 9002 Certified Plant.


Greensmaster® TriFlex® 3300/3320/3400/3420 Accessories*

8-BLADE DPA CUTTING UNITS 11-BLADE DPA CUTTING UNITS 14-BLADE CUTTING UNITSDPA CUTTING UNITS These cutting units will fit on the Greensmaster TriFlex Series.


Cutting height is adjusted on front roller by two vertical screws and held by two locking cap screws. Bench HOC range is .062"-.297" (1.6-7.5 mm). With high HOC kit, range is ..297-1.0" (7.5-25.4 mm). Effective HOC may vary depending on turf conditions and bedknife installed.

REEL WELDMENT Reels are 5" (13 cm) in diameter, 21" (53.3 cm) in length. EdgeSeries™ Reels blades are welded to 5 stamped steel spiders, and heat treated. The reel is ground for diameter and concentricity, and relief grind.

REEL BEARINGS Two stainless steel ball bearings, 30 mm inside diameter slip fit onto reel shaft retained by internally splined threaded insert. Low drag seals/slingers for added protection with o-ring sealed motor and counterweight. Reel position maintained by a wave washer with no adjusting nut.





BEDKNIFE Replaceable single edged, EdgeMaxTM Microcut Bedknife is standard on all cutting units.

BEDKNIFE ADJUSTMENT Dual screw, indexed “click” adjustment to the reel; detents correspond to .0007" (.018 mm) bedknife movement for each position.



TOTAL WEIGHT 8-blade: 80 lbs. (30.4 kg) with aluminum Wiehle Roller. 11-blade: 83 lbs. (37.7 kg) with aluminum Wiehle Roller. 14-blade: 86 lbs. (39 kg) with aluminum Wiehle Roller.


The Greensmaster® TriFlexTM is manufactured in Tomah, WI ISO 9002 Certified Plant.


Greensmaster® TriFlex® 3300/3320/3400/3420 Accessories*

TRIFLEX DPA CUTTING UNITS04651 8-Blade Cutting Unit



GREENSMASTER TRIFLEX ACCESSORIES

OPTIONAL TRIFLEX ACCESSORIES04720 Thatching Reel - TriFlex (set of 1)

119-1128 Individual dynaBLADE, 2mm thickness

117-6824 Individual dynaBLADE, 1.2mm thickness

117-6839 Replacement dynaBLADE kit, 1.2mm thickness (36 blades)

117-6840 Replacement dynaBLADE kit, 2mm thickness (36 blades)

121-6674 Individual Spring Steel Blade

121-6675 Replacement Spring Steel Blade Kit (36 pcs)

04722 Greens Tri-Roller - TriFlex (set of 1)

04723 Greens Spiker - TriFlex (set of 1)TOOLS

04399 Turf Evaluator




TRIFLEX SERVICE KITS

44969 1000 hour filter Maintenance Kit - Greensmaster TriFlex 3300 / 3320

44970 400 hour filter Maintenance Kit - Greensmaster TriFlex 3400 / 3420

TRIFLEX DPA CUTTING UNIT ROLLER SCRAPERS / BRUSHES / COMBS

04646 Rear Roller Scraper (Spring Loaded)

125-3503 Front Wiehle Roller Scraper - Narrow

125-3504 Front Wiehle Roller Scraper - Wide

125-3505 Front Roller Scraper - Full

115-7377 Front Wiehle Roller Scraper Brush - Narrow

115-7378 Front Wiehle Roller Scraper Brush - Wide

115-7379 Front Roller Scraper Brush - Full

115-7380 Front Wiehle Roller Scraper Comb - Narrow

115-7381 Front Wiehle Roller Scraper Comb - Wide

115-7382 Front Roller Scraper Comb - Full

107-9561 Anti Bobbing Roller - Scraper Kit (Front and Rear)

121-2260 Rear Roller Scraper - Adjustable

TRIFLEX TRACTION UNIT ACCESSORIES04716 Off-Greens Kit (Anti Bobbing)

04722 Tri-Roller Kit

04723 Spiker Kit

04714 3WD Kit

04730 Leak Detector

04554 Light Kit

04508 Seat Kit, Standard

04719 Seat Kit, Premium

92-7307 Armrest Kit - Standard

119-7105 Armrest Kit - Premium

119-1691 Hydraulic Oil Cooler Kit (Gas)

117-9314 Hydraulic Oil Cooler Kit (Diesel)

119-7129 2WD Weight Kit (Gas) (ANSI compliant)

121-6665 2WD Weight Kit (Diesel) (ANSI compliant)

120-5750 3WD Weight Kit (Gas) (ANSI compliant)

104-6540 Spark Arrestor Kit (Gas)

120-1951 Spark Arrestor Kit (Diesel)

115-4510 Canopy

119-1715 Utility Bag Kit


BIO-HYDRAULIC FLUID / HYDRAULIC FLUID / OIL108-1178 Premium Hydraulic Fluid, 5 gal. (18.9 L)




TRIFLEX DPA CUTTING UNIT ROLLERS04625 Full Roller DPA

04626 Narrow Wiehle Roller DPA

04627 Wide Wiehle Roller DPA

04249 Full Split Roller

04250 Wiehle Split Roller

04628 Solid Steel Roller Kit (Front Wide Wiehle, Rear Full)

04716 Anti Bobbing Kit

71-1550 2” Rear Wiehle Roller (cast iron)

125-5180 Rear Roller Extension Kit

120-9600 High Height of Cut Kit (.35 - .94)

04258 Extended Wiehle Roller


TRIFLEX DPA CUTTING UNIT ACCESSORIES04648 Universal Groomer Drive

04802 Groomer Reel – Twin Tipped

04270 Grooming Brush, Soft

04271 Grooming Brush, Stiff

04650 Rotating Rear Roller Brush

115-1880 EdgeMaxTM Microcut Bedknife


93-4262 Microcut Bedknife (HOC Range 1.58mm - 3.18mm)

93-4263 Tournament Bedknife (HOC Range 3.2mm - 6.35mm)

93-4264 Low Cut Bedknife (HOC Range 6.35mm and higher)

94-6392 Bedknife – High Cut



63-8600 Bedknife – Fairway

99-3794-03 DPA Bedbar, Aggressive (optional)

106-2648-01 DPA Bedbar, Less Aggressive (standard equipment)


greensmaster 1000 series – a new legend is born....greensmaster® flex 1820 & 2120 the...

Documents