gps tracker vt 310 bb manual

7/27/2019 Gps Tracker Vt 310 Bb Manual

1/21

ZY INTERNATIONAL LIMITED GPSTrackerVT310BBManual

GPS Vehicle Tracker VT310BB

USER MANUAL


2/21

ZY INTERNATIONAL LIMITED GPSTrackerVT310BBManual

1.Introduction........................................................................................3

2. VT310BB overview .5

3. Specification .. 12

4. Function .. ..15

5. Get start ....18

6. Trouble shoot .21

7. More SMS command .23


3/21

1.Introduction

VT310BB which come in a compact design is a powerful real

time fleet management and vehicle tracking system using

high sensitivity GPS and wireless GSM/GPRS communication.

This self-contained and autonomous tracking device including

GSM module, GPS receiver, Li-ion battery and Multi analog

input is able to be used as observing the location of

vehicle ,detecting temperature ,detecting fuel costing.

Figure 1. VT310BB appearance


4/21

2.VT310BB overview

2.1 VT310BB unit

VT310BB is designed in a compact and simple ruggedAluminum enclosure. At the end of the unit ,there are 2 LED

indicators shows the status of the unit. And various ports for

vehicle interface, USB interface, external GSM/GPRS antennaconnector ,external GPS antenna connector are on both side of

the device.

No. Name

1 Connect 1

2 Connect 23 External GSM antenna connect port

4 External GPS antenna connect port

5 External Micro phone connect port

6 GSM status indicator

7 GPS status indicator


5/21

2.2 LED indicators

Logo LED name Description

M GSM/GPRS statusindicator

Green LED on: GSM/GPRS connectionstatus

Green LED blinking: Boot completionstatusGreen LED off: Idle status

S GPS status indicator Orange LED on: GPS position fixedOrange LED blinking: During GPS signalreception

2.3 Connect 1

Please refer to the following table to understand the function

of each pin at UART port.

PinNumber

Description

AConfiguration Serial port RXD1(only for update)

BDigital input 3 IN3,which is negative

triggerC GND

DConfiguration Serial port TXD1(only for update)

C D


6/21

2.5 Connect 2

Please refer to the following table to understand the

function of each pin at Connect 3.

Pin

Number

Description

1 Digital input 1,also used asSOS input *

2 Digital input2 *

3 Digital input 4**

4 Digital input 5**

5 GND

6 Analog input 1

7 Analog input 2

8 Power

9 Digital output110 Digital output2

11 Digital output3

12 Digital output4

Remark

*: Digital input 1,Digital input2,Digital input 3 is negative

trigger

**:Digital input 4,Digital input 5 is positive trigger

2.6 External GSM/GPRS antenna

VT310BB has the quad-band GSM/GPRS antenna

according to the supported bandwidth in users areas.

2.7 External GPS antenna

VT310BB has an external GPS antenna.

2.8 Package contents

The basic package is including VT310BB,GPS antenna,

1 2 3 4

5 6 7 8

9 1

1

1


7/21

GSM/GPRS antenna, cables. The optional accessory

including :Hand-free kit, Mobile data terminal, CCD camera,

RFID reader, temperature sensor, tank fuel level sensor. For

more details about optional accessory ,please refer to GPS

AVL Accessory Guide V2[1].0

3Specification

3.1 Software Features

SMS mode/GPRS mode/SMS+GPRS mode

Position request via SMS or GPRS

Data logging capacity: up to max 144,000 pointStore in GSM blind area and forward when GSM signal

re-establish

Mileage reportUpload/download settings, locations, and update firmware via

GPRS

Configurable GEO-fencing

Configurable 2 analog input for status detectionConfigurable 5 digital input for status detection

Configurable 5 digital output for remote control of vehicle

3.2 Hardware Features

GSM/GPRS coreSimcom:SIM300D:900/1800/1900MHz

Simcom:SIM340D:850/900/1800/1900MHz

GSM/GPRS services: Data, SMS/GPRS class B,class 10,TCP

UDP,IP

Physical characteristicsDimensions(L*W*H): 104*73*29.8mm

Weight:approx:160g(including build-in battery)Temperature range

Operation:-20 Celsius degree to +80 Celsius degreePower sources

Input voltage:10~32 Volt DC regulated/Max 2ARechargeable Li-ion battery 1800mAh

Antenna


8/21

External GSM/GPRS antenna

GPS antenna

Indication:2 LED indicator for GSM/GPRS and GPS status

3.3 Technical specification

GSM/GPRS specification

FrequencyBands

Simcom 300D:900/1800/1900MhzSimcom 340D:850/900/1800/1900Mhz

GSM class Small MS

Transmit

power

Class 4(2w) at EGSM900 and GSM850

Class 1(1W) at DCS1800 and PCS 1900GPRSconnectivity

GPRS multi-slot class 10GPRS mobile station class B

Data GPRS Data up/downlink transfer:Max.85.6/42.8kbps

Coding scheme:cs-1,cs-2,cs-3 and cs-4Supports the protocols PAP and CHAP commonlyused for PPP connections

Data CSD CSD transmission rates:2.4,4.8,9.6,14.4 kbps

SMS SMS,MT,MO,CB,Text and PDU mode

Support transmission of SMS alternatively overCSD or GPRSUser can choose preferred mode

TCP/IP stack Internetservices:TCP,UDP,HTTP,FTP,SMTP,POP3

FAX Group 3:Class 1,Class 2

SIM Supported SIM card:3V

GPS module specification

Receive Frequency 1.57542Ghz +/-1.023MhzGeneral

GPS datum WGS-84Acquisition Rate Conventional mode

Cold/warm/hot start.

If you are using GpsGate Software, please contact us forwriting GpsGate protocol before delivery.


15/21

5.3 Device installation

5.3.1 Connect the external GSM antenna and GPS antenna

5.3.2 Open the rear cover and then insert SIM card

5.3.3 Connect the analog port & cables with the device andthe vehicle. The VIN ,GND and ignition signals of the

analog port should be connected to the vehicle. If

these signals are not connected to the vehicle, please

use power supply or 12/24V battery.

5.4 How to use external sensor

5.4.1 Connect external sensor with VT310BB

5.4.2 Control center send related command to tracker unitto set the parameter of using external sensor, suchas time interval of taking photo of CCD camera.

5.4.3 Receiving GPRS package which include detection

data.

For more info about how to use external sensor,

Please refer to GTP GPRS communication

Protocol for GPS Tracker

6 Troubleshooting

Problem: Unit will not turn on

Possible Cause: Resolution:

Wiring was not connected properly Check and make sure wiringconnection is in order.

Battery needs charging Recharge battery

Problem: Unit will not respond to SMS

Possible Cause: Resolution:GSM antenna was not installedproperly

Make VT310BB connected to GSMnetwork.

GSM Network is slow Wait for SMS. Some GSM networksslow down during peak time or whenthey have equipment problems.

Unit is sleeping Cancel sleeping modeWrong password in your SMS or wrong Write correct password or SMS


16/21

SMS format format

The SIM in VT310BB has run out ofcredit

Replace or top up the SIM card

No SIM card Insert working SIM card. Check inphone that the SIM can send SMSmessage.

SIM card has expired Check in phone that the SIM cansend SMS message. Replace SIMcard if needed.

SIM has PIN code set Remove PIN code by inserting SIMin you phone and deleting the code.

SIM is warped or damaged Inspect SIM, clean the contacts. Ifre-inserting does not help try

another to see if it will work.Roaming not enabled If you are in a different country your

SIM account must have roaming

enabled.

Problem: SMS received starts with LastPossible Cause: Resolution:

Unit does not have clear view of thesky

Move the antenna of the unit to alocation where the sky is visible.

VT310BB is in an inner place Wait for the target to come out

Battery is low Recharge the unit and the GPS willstart working.

Problem :Cannot receive /send GPRS packagePossible cause

APN is not setting correctly Check local telecommunicationprovider and set the correct APN

APN is longer than 14 characters Use SMS command to settingAPN ,instead of configuration tool

Local firewall block GPRS package Check with IT and close firewallSIM card cannot support GPRSfunction

Check with local telecommunicationprovider

Problem: Continuous sendinglogon info

Possible cause:Power isnot enough that the trackercontinuous reset

Charge the tracker at least 3 hours

GSM signal is too weak Check if the blue led is light for 0.1sand dark for 2.9s.If yes, it proves

the GSM signal is too weak. Pleaseput the GSM and GPS antenna tooutdoor.

Problem: Preset number for SOSbutton cannot work

Possible cause

SMS format is unique ,addingcountry ,city info

Check local telecommunicationprovider to get local SMS format


17/21

7 SMS Command List

(Remarks: ****** is users password, and the default

password is 000000)

Command Format Remark

Get current location W******,000 Get current location ofunit

Get current location W******,001,****** ****** is old password

###### is newpassword

Set interval forautomatic timed report

W******,002,XXX XXX is the interval inminute. If XXX=000 it willstop tracking

Set preset phone

number for SOS button

W******,003,F,P,T1

(W******,003,F,P,T1,T2)

F=0, to turn off this

function;F=1, only sending SMS;F=2, only calling presetphone number;F=3, both SMS and

calling (default)P=1, set a authorizednumber for SOS buttonP=2, set a authorizednumber for BP=3, set a authorized

number for C

T1: Preset phonenumber. Max. 16 digitsWhen there is T1 only,then it can be set as SMSNo, and the calling No., if

there is also T2, then T1is the preset SMS no.,and T2 will be the callingNo.

Set low power alert W******,004,X X (voltage preset value)

=0 , to turn off thisfunction

=1,


18/21

alert

Set over speed alert W******,005,XX XX (the preset value ofspeed)

=00 , to turn off thisfunction=[01, 20] (unit: 10Km/h)

For example,W000000,005,08, it willsent alert when it is over

80Km/h

Set Geo-fence alert W******,006,XX XX ( preset distance tooriginal place )=00, close=01, 30m

=02, 50m=03, 100m=04, 200m=05, 300m=06, 500m=07, 1000m

=08, 2000m

Extend Settings W******,008,ABCDEFGHIJ### A=0, turn off thefunction of sending anSMS location report tothe authorized phone

number when it makes acall to unit.A=1, turn on the functionof sending an SMSlocation report to theauthorized phone

number when it makes acall to unit.B=0, location data ofNMEA 0183 GPRMC willbe interpreted intonormal text for easy

reading.For example:Longitude = 114 degree -04 cent -57.74 secondLatitude = 22 degree -32cent -40.05 second

B=1, location datacomplies with NMEA 0183GPRMC protocol.For example:$GPRMC,072414.000,V,3114.3763,N,12131.325

5,E,0.00,0.00,050805,*0


19/21

0C=0, turn off the functionto automatically hang up

an incoming call.C=1, turn on the functionto automatically hang up

an incoming call after 4 -5 rings.D=0, Turn off the

function of sending anSMS when unit is turnedon.D=1, Turn on thefunction of sending anSMS to SOS number

when unit is turned on.E=0, reservedE=1,unit shuts down

automatically when thepower voltage lower than3V.

F=0, Turn off the alertwhen unit enters GPSblind area.F=1, Turn on the alertwhen unit enters GPSblind area. SMS is to be

sent to SOS numberG=0, LED light worksnormally

G=1, LED light stopsflashing when unitworking.

H must be 0I=0 , close power cutalaetI=1 , open power cutalertJ=0 , close the beep

sound when callingJ=1 , open beep soundwhen calling

### is the endingcharacter

(default value is:ABCDEFG=1000100001 )

Set ID (14 digits at most) W ******,010,tel 14 digits at most

APN Setting W******,011,APN,APN User name,APN Password

If no APN name andpassword required, just

insert APN only;


20/21

APN defaulted as

CMNET;APN+APN name +

password not over 39characters.(default:CMNET

Set IP Address and Port W******,012,IP,PORT IP: xxx.xxx.xxx.xxxPORT [1,65534]

Enable GPRS TrackingFunction

W******,013,X X=0 closeGPRSdefault

X=1 open TCP

X=2 open UDP

Set Time Interval forSending GPRS Packet

W******,014,TTTTT XXXXX should be in fivedigitals and in unit of 10seconds.XXXXX=00000, to turn

off this function;XXXXX=00001~65535,

time interval for sendingGPRS packet and in unitof 10 seconds.

Set Logo for GPRS (special) W******,016,Logo Logo gets 16 bytes at

most

Output Control W******,020,P,F P =1, Out1=2, Out2=3, Out3=4, Out4

=5, Out5F =0, to close the output=1, to open the output

Output Control (Safemode) W******,120/220,DATA (GPS tracking speed islower than 10Km/h orlower than 20Km/h)

ABCDE represents Out1,Out2, Out3, Out4, andOut5 respectively.If A or B or C or D or E,=0, to close the output

=1, to open the output=2, to remain previousstatus

Set sleep mode

for saving power

W******,021,XX### XX=00 turn off sleep

modeXX=01 sleep mode

XX=02 deep sleep mode### is the endingcharacter

Set power saving modewhen unit(GT60 &

VT310) is inactive

W******,026,XX XX=00, to turn off thisfunction

XX=01~99, to set thisfunction. It is in unit of


21/21

minute.Example:If XX=10, VT310 will

enter power saving modeafter it is immobile for 10minutes.

Set phone number forwiretapping(OPTIONAL)

W******,030,T T is the telephonenumber for wiretappingand max. 16 digits

Set interval forlogging( VT310)(Note: this interval is notrelevant to the interval ofcontinuous tracking)

W******,031,T X=0, to turn off thisfunctionX=[1, 65535] to setinterval in second.For example,

W000000,031,60, VT310will store location dataevery 60 seconds.

Set time zone difference W******,032,T T=0, to turn off thisfunctionT=[1, 65535] to set time

difference in minute toGMT. Default value isGMTFor those ahead of GMT,just input the time

difference in minutedirectly. For example,W000000,032,120

-is required for thosebehind GMT. Forexample,

W000000,032,-120.

Set character for SOSalert message

W******,033,P,char Char is the character inSOS message and max32 characters

Reset mileage report

The mileage report canbe cleared by SMScommand

W******,991,199##

ZY INTERNATIONAL LIMITED (Alibaba Gold Supplier)Website: http://www.zhyichina.com http://www.zhyichina.cn

E-Mail: [email protected] MSN: [email protected]

Wholesale: http://www.zywholesale.com http://www.zyebuy.com
http://www.zhyichina.com/http://www.zhyichina.cn/mailto:[email protected]:[email protected]://www.zywholesale.com/http://www.zyebuy.com/http://www.zyebuy.com/http://www.zywholesale.com/mailto:[email protected]:[email protected]://www.zhyichina.cn/http://www.zhyichina.com/

gps tracker vt 310 bb manual

Documents